Beruflich Dokumente
Kultur Dokumente
ATSM880079RCS
MODEL
GF4760A
GF-1770A
GF4760X
GF-1770X
SPECIFICATIONS
Playback key-+----
Stop key A
Eject key/
Mode selector
V o l u m e control
_ Tuning control
- Built-in Microphone
Cassette _L
compartment
Mains voltage
- selector (GF-1760X
and GF-1770x Only)
Figure 2-1
Iv lonitor switch-
-External microphone socket
Battery compartment
Figure 2-2
-2- (, -, .^
_;
DISASSEMBLY
BACK CABINET REMOVAL (Refer to Figure 3-l) PRINTED WIRING BOARD REMOVAL
1, Take out the cassette tape from the cassette compartment. (Refer to Figure 3-2)
2. Remove the battery compartment lid and take out four 1. Remove four (4) screws retaining the main P.W. Board
(4) batteries and main switch P.W. Board.
3. Remove the tuning control, and volume control knobs.
4. Remove five (5) screws retaining the back cabinet and
lightly open it.
5. Disconnect the antenna lead wire and battery lead from
the battery terminals.
6. Then the back cabinet can be removed
Figure 3-3
-3-
T O R Q U E A D J U S T M E N T (Refer to Figure 6-1, 6-2
and 6-3)
1 Set the torque measuring reel to the turntable (to the
take-up side at play or fast forward mode and to the
supply side at rewind mode). Turntable
2. Then, rotate the reel in the same direction as for turntable
and read the torque value when the pointer is stabrlized.
3. Normal torque values are tabulated below.
Adjustment point
J Figure 6-3
Figure 6-2
Make sure that the auto stop mechanism acts rightly at the
tape end.
If not, adjust the auto stop lever stroke as indicated right.
Figure 6-4
-6-
MECHANICAL ADJUSTMENT
RECORD/PLAYBACK
HEAD
External
speaker
Play mode socket IJlOl)
6 . 3 kHz
Recorded
Tape
. 4ohm
/ Playback 12Wb
Head
Figure 5-I
\
Tension gauge
Figure 5-2
-5-
VOLTAGE SELECTION (GF-1760X and GF-1770X)
(Refer to Figure 4-l 1
Figure 4 - l
Pointer
/
Pullev
Figure 4-2
-4-
MAIN SWITCH POSITION ADJUSTMENT
(Refer to Figure 7-1 and 7-2)
While the unit in stop mode, adjust the main switch (SW4)
position as illustrated in Figure 7-1 and 7-2. After finished
adjustment, check the main switch operates normally.
MAIN SWITCH
Opened (SW4)
/
Adjustment pad
Normal
ii
-7-
ELECTRICAL CHECK
1. Connect a 4 ohm (2W, 5%) dummy load resistor to external 4. Place the unit in play mode with the volume control
speaker socket (JlOl) and connect V.T.V.M. across the at maximum.
load. 5. If the playback sensitivity is normal, the reading on the
2. Set the mode selector switch (SWI) to “TAPE” position. V.T.V.M. should be approximately 0.N.
3. Insert the test tape (MTT - 112 SP. 333 Hz, -20 dB
recorded)
Oscilloscope
I I
V.T.V.M.
External I I
speaker r-----I I/ITT42
socket (JIOI)
PLAY MODE
TEST
TAPE 1 4ohm
MTT WV)
IIZSP I
Figure 8-1
1. Connect a 4 ohm (2W, 5%) dummy load resistor to external 4. Connect the signal generator for 1 kHz, -60 dB (0 dB:
speaker socket (JlOl) and connect V.T.V.M. across the 1V) to external microphone socket (J102).
load. 5. If the record sensitivity is normal, the reading on the
2. Set the mode selector switch (SWI) to “TAPE” position. V.T.V.M. should be approximately 520mV f 2 dB.
3. Insert the tape.
Oscilloscooe
External
External V.T.V.M.
speaker
IV microphone rnrl,n+
a”,,\,; I\dI1 I”
n’
1 )
socket (J 102)
Signal generator
0 o--
0 *-
4 ohm
1 kHz (2W)
Figure 8-2
-8-
EQUIVALENT CIRCUIT OF IC (ICl)
I C I : 92LIC-035 (HA1361)
INPUT
I
E-
I --r&
4, WC--
8
L ---c
GND
Figure 9
-9-
GENERAL ALIGNMENT INSTRUCTIONS
Should it become necessary at anytime to check the align- 3) Attenuate the signals from the generator enough to swing
ment of this receiver, proceed as follows; the most sensitive range of the output meter.
I) Connect an output meter across the speaker voice coil lugs. 4) Use a non-metallic alignment tool.
2) Set the volume control at maximum. 5) Repeat adjustments to insure good results.
ALIGNMENT POINTS
TP2 TPI
TC2
TCI
TP3
TC3
Tl
T6
Figure 10
-lO-
AM ALIGNMENT CHART
1. Set the Band Selector switch at “AM” position.
STE
TEST SIGNAL GENERATOR
- r RECEIVER
ADJUSTMENT
;TAGf CONNECTION TO INPUT SIGNAL
DIAL SETTING REMARKS
RECEIVER FREQUENCY
i-
IF Connect signal generator 455 kHz. (400 Hz, T4
through a 1OK ohm resistor 30%. AM modulated.) T5
to the antenna tuning capaci- T6
tor.
Sround lead to the receiver
chassis.
__-
Use radiation loop. Loop Exactly 510 kHz. Tiijii Sameassw 1. Adjust the AM
of several turns of wire, or 1400 Hz. 30%. AM oscillator coil
place generator lead close modulated.) (L8).
to receiver for adequate
signal pickup. Connect
generator output to one
Band end of this wire.
Cover i
3 age Same as step 2 Exactly 1650 kHz. High end of dial Same as step I. Adjust the AM
(400 Hz, 30%, AM [minimum capacity) oscillator trim-
modulated.) mer (TC3j.
A Same as step 2 Exactly 600 kHz 600 kHz Adjust the AM an-
1400 Hz, 30%, AM tenna coil iL7).
modulated (See NOTE A.)
Track
ing ,r Same as steo 2. I- Exactly 1400 kHz
(400 Hz, 30%, AM
1400 kHz Adjust the AM
antenna trimmer
modulated.) (TC4).
(See NOTE A.)
i
Repeat steps 2, 3, 4 and 5 until no further improvement can be made
Check the alignment of the receiver antenna coil by bringing requires less inductance. Change loop inductance by sliding
a piece of ferrite (such as a coil slug) near the antenna loop the bobbin toward the center of ferrite core to increase
stick, then a piece of brass. if ferrite increase output, loop inductance, or away to decrease inductance.
reauires more inductance. If brass increases output, loop
FM ALIGNMENT CHART
Connect signal generator Exactly 10.7 MHz iigh end of dial Connect V.T.V.M 3etune 12, T3
througil a 5PF capacitcr (400 Hz, 30%. F M [minimum capacity) across the resistor Tune Tl for
1 IF to the emitter of Q2. (TP3) modulated) R28 naximum
Connect generator ground indication.
lead to the receiver chassis.
t
i
I Exactly See NOTE B See NOTE B.
Ratio 10.7 MHz. Same as step 1.
T
Same as step 1.
2
Detector (Unmodulated)
+
Connect signal generator Exactly 87 MHz. Low end of dial Adjust for maxi- Adjust the FM
throught a FM dummy, (400 Hz, 30%, FM (maximum capacity) mum output speaker oscillator coil L5 &
including output impedance modulated) voice coil lugs. L6.
of signal generator to the
Band
rod antenna. (TPl)
Coverage
(Refer to Figure 12-l)
Ground lead of generator
connected to the receiver
chassis.
-i
Same as step 3. Exactly 109 MHz. High end of dial Same as step 3. Adjust the FM
(400 Hz, 30%. FM (minimum capacity) oscillator trimmer
Band modulated) TCI.
Coverage
Same as step 3. Exactly 108 MHz. 108 MHz Same as step 3. Adjust the FM RF
(400 Hz, 30%. FM trimmer TCZ.
modulated)
6 Tracking
7
1
Repeat steps 3,4, 5 and 6 until no further improvement can be made.
-!l
1) ConnectV.T.V.M. (0.1 volts range DC scale) across the 3) Change signal generator frequency 10.7 MHz + 100 kHz
resistor (R39). and -100 kHz approximately.
2) Adjust 13 for 0 volt on V.T.V.M. 4) Adjust T2 for balanced peaks. Peak separation should
be approximately 200 kHz.
TO ANTENNA
R I - 37.5 ( o h m )
’- 75 (ohm) <R2 s 7 5 (ohm )
* TO C H A S S I S G R O U N D .
z = OUTPUT IMPEDANCE OF SIGNAL GENERATOR
-12-
- -.--mm
QI 2SC 1417G 02 2X 1417F 08 2SC458D
FM ANT
FM RF AMP FM CONV.
BUILT
IN MIC 6.0”
3
MAIN AMP
SWP-A SWP-E
REC - PB
sw2-a SWP-c p
ci
I,!
I
Q7 2SC458C
MIC MIX AMP ’ 3*.0-.9w ,“,. ^
VOLUME
SW1 (6-D): Mode selector (FM/AM/TAPE) switch shown SW3 : Monitor switch shown in
in “AM” position. sw4: Main (motor) switch she’
SW2 (A-F) : Record/playback switch shown in “record” sw5: AC/BATTERY selector sw
position. Y” position.
SW6 : Mains voltage selector s’
24OV” position. (GF-1761
(Specifications or wiring diagrams of this model are subject to change for the improvement witho
Figure 13 SCHEMATIC
-13-
c1417G 04 2SCl417G Q5 2SCl417G
I IF AMP FM/AM IF AMP FM/AM IF AMP
SW5
AC- BATTERY
SELECTOR
SW4
MAIN SWITCH
\
\
\
\
-- L
CHEMATIC DIAGRAM
-14-
-~_. __..-_--.- - - I - - - - -
I - mode switch
ROD ANTENNA
-15-
I I f-1 I
139--- - 138
I
II8
124 _//__i
2 3
-19-
107
108
143
-2o-
PARTS LIST
REF.
NO.
PART NO. D E SC R I P T I ON jC()DE~ REF.
NO PART NO. D E S C R I P T I ON
-23-
PARTS LIST
REF. REF.
PART NO. DESCRIPTION /C( 3DE PART NO. DESCRIPTION DDE
NO. NO.
-22-
REPLACEMENT PARTS LIST
“HOW TO ORDER REPLACEMENT PARTS”
To have your order filled promptly and correctly, please furnish the following information.
1. MODEL NUMBER 2. REF. NO.
3. PART NO, 4. DESCRIPTION
NOTES: Be sure to use regular parts for securing the safety and reliability of the set. Parts marked with ”A ” and parts cross
hatched (in black) are especially important for maintaining the safety and protecting ability of the set.
Be sure to replace them with parts of specified part number.
REF. REF.
PART NO. DESCRIPTION C ODt PART NO. DESCRIPTION ODI
NO. NO.
T2 SZLIFT-OllB FM Discriminator AD
INTEGRATED CIRCUIT T3 SZLIFT-OIIC FM Discriminator AD
T4 92LI FT-011 D AM 1st IF AE
ICl 92LIC035 Audio (HA1 361) AQ T5 92Li FT-011 E AM 2nd IF AE
AE
(CR
TRANSISTORS AT,
_/. /
-21-
(A8008-1.55~
P r i n t e d i n Ja