Beruflich Dokumente
Kultur Dokumente
Application
Benefits Features
www.frese.eu
Technote Page 2 of 15
4 5 4
2
3 1
Function
Frese OPTIMA Compact can be flushed and commissioned
Design before the actuator is installed.
The design of Frese OPTIMA Compact combines high The presetting of the dial is user-friendly requiring only a simple
performance with small size and compact construction. flow vs. presetting graph. Once the flow is set, the actuator can
The main components of the valve are: be mounted and the valve ready to operate.
1 Differential pressure control For lowest energy consumption, check the differential pressure
at the index valve to set the pump at minimum speed.
2 Modulating control component
Pre-setting
scale
1 & 2
Diaphragm based combined
pressure control, flow
balancing & modulating unit
Operation principle
The innovative design of Frese OPTIMA Compact features a Whilst the control component provides proportional modu-
modulating control component that retains 100% authority lation irrespective of the preset flow, the automatic balancing
at all times. guarantees that the flow will never exceed the maximum preset
flow.
With the Frese OPTIMA Compact, there are two independent
movements for the presetting and the modulating function. Regardless of pressure fluctuations in the system, the maxi-
During presetting, the inlet area moves radially without mum flow is kept constant up to a maximum differential pres-
interfering with the length of the stroke. During modulating, sure of 800 kPa.
the inlet area moves axial taking advantage of the full stroke.
250
200
100
50
220
200 4
180
160
Preset flow: 200 l/h 140
3
120
LIN 2
100
80
Strainer
G
LO
60
1
40
20
0
0 2 4 6 8 10
Voltage (V)
250
7V
200
Ball Valve
100 3V
50
www.frese.eu
Technote Page 4 of 15
Technical data
Valve housing:
DN10-15-20-25-32 DZR Brass
L5
L6
DN40-50 Ductile Iron
DP controller: PPS 40% glass
Spring: Stainless steel
Diaphragm: HNBR
O-rings: EPDM L1 L7
Pressure class: PN25 M/M with couplings
Max. differential pressure: 800 kPa
Needles for DP measurement: Max diameter, ø3.2 mm
Length, 25 - 40 mm
Thread: ISO 228
Medium temperature range: -10°C to 120°C
L3
L4
When used at temperatures below 0°C, a stem heater Thermo Motoric
must be used, to prevent ice on the spindle actuator actuator
The pipe system shall be properly ventilated to avoid risk of air
pockets. Glycolic mixtures up to 50% are applicable (both ethylene
L2
L2
and propylene).
Recommendation: Water treatment to VDI 2035.
Frese A/S can accept no responsibility if another actuator is used L L
instead of the Frese actuator.
Weight Basic 0.36 0.38 0.42 0.40 0.45 0.51/1.02 0.55/1.04 1.17 1.17 - -
kg P/T 0.45 0.47 0.52 0.50 0.54 0.62/1.12 0.65/1.14 1.27 1.27 3.28 3.71
EN Frese OPTIMA Compact DN10-DN50 JUL 20
Flow
Dim. DN10 - DN15 DN15 - DN20 DN20 DN25 DN25L DN32 DN40 DN50
Type Low High High Low High - - -
l/h 30 - 200 65 - 370 100 - 575 220 - 1,330 300-1,800 280-1,800 600-3,609 550-4,001 1,370-9,500 1,400-11,500
Flow l/s 0.008-0.056 0.018-0.103 0.028-0.160 0.061-0.369 0.083-0.500 0.078-0.500 0.167-1.003 0.153-1.111 0.381-2.639 0.389-3.194
gpm 0.13 - 0.88 0.29 - 1.63 0.44 - 2.53 0.97 - 5.85 1.32-7.93 1.23-7.93 2.64-15.89 2.42-17.62 6.03-41.83 6.16-50.63
www.frese.eu
Technote Page 5 of 15
www.frese.eu
Technote Page 6 of 15
X
2.5 mm stroke = 11.4 mm M3
5.0 mm stroke = 9.3 mm
0x
1,5
mm
www.frese.eu
Technote Page 7 of 15
Product programme
Dim. Type Flow l/h Flow l/s M/M M/M, PT plugs F/F F/F, PT plugs
Low 2.5 mm 30-200 0.008-0.056 53-1300 53-1320 - -
DN10
Low 5.0 mm 65-370 0.018-0.103 53-1309 53-1329 - -
Low 2.5 mm 30-200 0.008-0.056 53-1302 53-1322 53-1342 53-1362
Low 5.0 mm 65-370 0.018-0.103 53-1310 53-1330 53-1350 53-1370
DN15
High 2.5 mm 100-575 0.028-0.160 53-1304 53-1324 53-1344 53-1364
High 5.0 mm 220-1,330 0.061-0369 53-1305 53-1325 53-1345 53-1365
High 2.5 mm 100-575 0.028-0.160 53-1312 53-1332 53-1352 53-1372
DN20 High 5.0 mm 220-1,330 0.061-0369 53-1308 53-1328 53-1348 53-1368
High 5.5 mm 300-1,800 0.083-0.500 53-1311 53-1331 53-1318 53-1338
DN25 Low 5.5 mm 280-1,800 0.078-0.500 53-1317 53-1337 53-1319 53-1339
DN25L High 5.5 mm 600-3,609 0.167-1.003 53-1313 53-1333 53-1353 53-1373
DN32 5.5 mm 550-4,001 0.153-1.111 53-1314 53-1334 53-1354 53-1374
DN40 15 mm 1,370-9,500 0.381-2.639 - - - 53-1375-01
DN50 15 mm 1,400-11,500 0.389-3.194 - - - 53-1376-01
Accessories
Frese no. Product Dimension Thread Material
43-1330 DN10 G 1/2 - R3/8
Couplings 2 pcs,
43-2330 DN15 G 3/4 - R1/2 DZR Brass, CW602N
incl gasket
43-3330 DN20 G 1 - R3/4
38-0857 DN10-15-20
For heating EPP, Max temperature
38-0858 Insulation DN25
applications only 1200C
38-0859 DN25L-32
Frese no. Product Type Suitable for valves Suitable for actuators
All variants
58-8956 Stem Heater 24 V AC/DC, 10 W DN10-DN32
DN10- DN32
www.frese.eu
Technote Page 8 of 15
0.050 180
0.044 160
15.4
0.039 140
0.033 120
0.022 80
0.017 60
14.5
0.011 40
14.3
0.006 20
0 0
0 1 2 3 4
Pre-set
17.2
0.083 300
16.5
0.056 200
15.7
EN Frese OPTIMA Compact DN10-DN50 JUL 20
14.6
0 0
0 1 2 3 4
Pre-set
www.frese.eu
Technote Page 9 of 15
0.139 500
17.6
0.111 400
0.056 200
15.5
0 0
0 1 2 3 4
Pre-set
0.333 1200
0.306 1100
0.250 900
0.222 800
0.194 700
19.2
0.167 600
0.139 500
EN Frese OPTIMA Compact DN10-DN50 JUL 20
0.111 400
17.0
0.083 300
16.0
0.056 200
0.028 100
0 0
0 1 2 3 4
Pre-set
www.frese.eu
Technote Page 10 of 15
0.444 1600
0.389 1400
29.5
0.333 1200
0.278 1000
22.9
0.222 800
0.167 600
22.1
0.111 400
17.8
0.056 200
0 0
0 1 2 3 4
Pre-set
0.444 1600
0.389 1400
24.2
0.333 1200
0.278 1000
0.167 600
EN Frese OPTIMA Compact DN10-DN50 JUL 20
16.1
0.111 400
15.3
0.056 200
0 0
0 1 2 3 4
Pre-set
www.frese.eu
Technote Page 11 of 15
23.0
0.972 3500
0.833 3000
19.5
0.694 2500
0.556 2000
18.0
0.417 1500
17.3
0.139 500
0 0
0 1 2 3 4
Pre-set
0.972 3500
0.694 2500
0.417 1500
EN Frese OPTIMA Compact DN10-DN50 JUL 20
0 0
0 1 2 3 4
Pre-set
www.frese.eu
Technote Page 12 of 15
2.222 8000
1.944 7000
17
1.667 6000
1.389 5000
1.111 4000 11
0.833 3000
0.556 2000 10
10
0.278 1000
0 0
0 1 2 3 4
Pre-set
2.778 10000
2.222 8000
22
1.667 6000
1.111 4000 13
EN Frese OPTIMA Compact DN10-DN50 JUL 20
0.556 2000 11
10
0 0
0 1 2 3 4
Pre-set
www.frese.eu
Technote Page 13 of 15
www.frese.eu
Technote Page 15 of 15
Documentation formula
Valve ID Valve type Dimension Pre-setting Verified Δp Min. Δp Flow
(own choice) [kPa] (see flow rate graph)
[kPa]
www.frese.eu