Beruflich Dokumente
Kultur Dokumente
employs network-based application recognition (NBAR) to classify and mark voice traffic
generates interface configurations, policy maps, class maps, and access control lists
Cisco AutoQoS is supported on which three interfaces and PVCs? (Choose three.)
ATM PVCs
ATM SVCs
Gigabit Ethernet
Refer to the exhibit. The AutoQoS for the Enterprise feature has been configured on the interface. What
two steps should be performed if the bandwidth on the interface gets changed to 500 kb/s? (Choose two.)
Re-enter the auto discovery qos command to resume the autodiscovery phase.
Use the no auto discovery qos command to stop the autodiscovery (data collection) configuration phase
and apply the auto discovery qos command to resume the autodiscovery phase.
Use the no auto qos command to remove the AutoQoS and apply the auto qos command to resume the
AutoQoS services.
No additional configuration is required. The AutoQoS for the Enterprise feature will respond
automatically to changes made to the bandwidth.
What requirement should be taken into consideration when running Cisco AutoQoS on the network?
The speed of the link determines the configurations that are generated by Cisco AutoQoS.
What command is used on a Cisco router to display the Cisco AutoQoS interface templates, policy maps,
class maps, and ACLs?
What is the function of the show mls qos maps dscp-cos command?
to display the DSCP values that AutoQoS is using to classify traffic on a switch
to display the the DSCP values that AutoQos is using to classify traffic on a router
When the Cisco router interface command auto discovery qos is entered, what is the default time interval
for the autodiscovery phase?
1 day
2 days
3 days
1 week
Cisco AutoQoS classifies voice, video, and data traffic using NBAR.
When the command auto qos voip trust is used on an interface of a Cisco IOS-based switch, which
statement is true?
The ingress interface will trust the ingress CoS QoS marking.
The egress interface will trust the ingress CoS QoS marking.
The egress interface will trust the egress CoS QoS marking.
The ingress interface will trust the egress CoS QoS marking.
What two requirements should be taken into consideration when configuring AutoQoS? (Choose two.)
The amount of bandwidth that is configured must be the same on both ends of the link.
Multilink PPP (MLP) must be configured for serial interfaces with a link speed of 768 kb/s or lower.
Which two statements are true when the AutoQoS for Enterprise feature is enabled?
All QoS policies must be removed from the interfaces before AutoQoS is enabled.
All WAN settings for fragmentation, compression, encapsulation, and Frame Relay must be preconfigured
before AutoQoS is enabled.
All QoS settings for switch ports where IP phones are connected must be preconfigured before the
AutoQoS is enabled.
The class map and policy map must be preconfigured for all subinterfaces before the AutoQoS is enabled.
Which three key elements of QoS deployment does Cisco AutoQoS address? (Choose three.)
application marking
policy evaluation
configuration
monitoring
consistency
redundancy
Which two prerequisites should be verified prior to the implementation of Cisco AutoQoS in any
environment? (Choose two.)
QoS policy should be configured on the interface before Cisco AutoQoS is implemented.
Routers that support the modular QoS CLI (MQC) reserve up to 50% of the interface bandwidth for user-
defined classes.
If the device is reloaded after Cisco AutoQoS is configured and after the configuration is saved to
NVRAM, Remote Monitoring (RMON) threshold commands may generate some warning messages.
Cisco AutoQoS is supported only on ATM PVCs, serial interfaces with PPP or HDLC, and Frame Relay
multipoint subinterfaces.
What output does the show auto qos command display on a Cisco router?
the data that is collected during the autodiscovery phase of Cisco AutoQoS
the policies that are applied specifically to Frame Relay DLCIs and ATM PVCs
What output does the show policy-map interface command display on a Cisco router?
packet statistics of all classes that are configured for all service policies on the specified interface
Frame Relay policy information that is related to generic traffic shaping (GTS)
Before an administrator can use the auto qos voip command, which two steps should be completed?
(Choose two.)
provisions LLQ for the VoIP bearer and bandwidth guarantees for control traffic
enables link efficiency mechanisms, such as LFI and compressed RTP (cRTP) where required
What information can be verified when the command show auto discovery qos is issued on a Cisco router?