Beruflich Dokumente
Kultur Dokumente
99 M
5.961-117
11/03_2006738
Operating Instructions
PRESSURE WASHER
2
Contents
Before first use of the unit read these operating instructions and act in accordance with
them. Keep these operating instructions in a safe place for later use or for a subsequent
owner.
For additional
information
see page 8
and following
4
Operation with high pressure
5
Operation with Detergent
6
Finishing the operation Care, storage
7
Environmental protection ! Never touch the mains plug and the
socket with wet hands.
! The connection between connection line
Dispose of packaging
and extension line must not lie in the
The packaging materials are recyclable. water.
Please hand in the packaging for recycling. ! All current-carrying components within
the working area must be jet-proof.
Dispose of old equipment
- The appliance may only be connected to
In the development of this appliance careful an electrical connection that was performed
attention has been given to its ability to be by an electrician according to IEC 60364.
easily recycled. Nevertheless, it contains - Only connect the appliance to alternating
parts or substances which should not go current. The voltage must comply with
into the household rubbish. You can obtain the voltage specified on the typeplate.
information from any Kärcher sales house
- Minimum fuse protection of the socket 10
about disposal facilities which protect the
A (delay-action fuse).
environment.
- To avoid electric accidents, we recommend
Save water to use sockets with a series connected
In comparison to other cleaning methods, residual current operated device (rated
by the use of this unit you save up to 85 % breaking current max. 30 mA).
of the water otherwise needed. The unit can - Warning: Inappropriate extension lines
also be operated with rain-water (use a water may be dangerous. If you work outside,
filter). only use extension lines that are approved
and specifically labelled and provide of a
Ease the burden on waste water sufficient conductor cross section:
Please use the cleaning agents sparingly. 1 to 10 m: 1.5 mm² 10 to 30 m: 2.5 mm²
Observe the dosage recommendations which - The plug and the coupling of an extension
are supplied with the cleaning agents. line must be waterproof.
- Always unwind the extension line
Before the First Use completely from the cable drum.
Connection to the Water Conduit
Assembly
Please observe the provisions of the local
Check the contents of the box when unpacking water supply company.
the appliance. If you detect any transport
damages, please contact your dealer. Only use supply hoses (not included in the
delivery) with the following dimensions:
Electrical Connection - minimum length 7.5 m
! Never use defect connection or - minimum diameter ½‘‘
extension lines! If the connection line is Please see the typeplate or the section
damaged, it must be replaced with a ”Specifications” for the connection values.
special connection line that is available
from the manufacturer or his customer
service.
! Please make sure that the connection or
extension lines are not damaged by being
ran over, pulled or dragged. Protect the
connection lines from heat, oil, and sharp
edges.
8
Operation • Screw the suction hose with filter (not
included, order-no. 4.440-238) onto the
! Serious danger! water connection of the unit.
Vehicle tyres and tyre valves can be damaged • Hang the filter in the container.
by the high-pressure jet and become • Vent the unit before operation.
perforated. The first sign of this is a – Unscrew the high-pressure line at the
discoloration of the tyre. When cleaning high-pressure outlet of the unit.
them maintain a distance of at least 30 cm. – Switch on the unit and let it run until
Never grasp the power plug with wet hands. water free of bubbles emerges at the
Before each use check the power cord and high-pressure outlet.
power plug for damage. Have a damaged – Switch off the unit and screw on the
power cord replaced immediately by an high-pressure hose again.
authorized Kärcher service point or an
Preparation
electrical specialist.
Before each use check the high-pressure • Insert power plug.
hose for damage. Replace a damaged high- • Turn master switch to “I”.
pressure hose immediately.
Switching on
! Danger of injury! • Press safety ratchet on the handgun and
Owing to the water jet emerging from the pull the lever.
high-pressure nozzle a recoil force operates
on the handgun. Ensure you have a secure Switching off
footing and hold the handgun and spray • Release the lever.
lance firmly. During breaks in work and when leaving
If necessary wear protective clothing for the unit secure it against inadvertent
protection against return spray. switching on by pressing the safety ratchet.
Water supply Working with accessory
Caution! Impurities in the intake water
■ Washing brush
damage the pump. To prevent this we
expressly urge you to use the Kärcher water The washing brush is ideally suited for the
filter (not included, order no. 4.730-097). cleaning of vehicles.
The operation of the high-pressure cleaner Note: Please make sure that the washing
with a closed water supply line causes brush is free from dirt or other particles.
damage to the pump. Please never operate Otherwise, it may cause defects in the paint
the high-pressure cleaner with a closed work. Please make also sure that the water
water supply tap. flow is ensured.
The unit can either be supplied from the ■ Spray lance with 4-jet nozzle
water main or from water in an open container. • Release the trigger of the handgun.
Water supply from the water main • Rotate the nozzle head until the symbol
• Connect a supply hose (not included) to is aligned with the marking on the spray
the water inlet of the unit and to the water lance.
supply (e.g. water tap). Note: The marking on the spray lance must
• Open the water supply. be up during operation.
Water supply from an open container
• Unscrew the coupling part for the water
inlet.
9
Meaning of the symbols Safekeeping
Low-pressure fan jet; for operating with Caution! Frost can destroy an incompletely
detergent or for cleaning with low emptied unit. In the winter keep the unit in
pressure.
a frost-free room.
High-pressure pencil jet; for especially • Separate the spray lance from the handgun.
stubborn spot soiling.
• Wind up the power cord and, for example,
High-pressure fan jet; for large area
hang it around the handgun.
soiling.
High-pressure rotating pencil jet; for
Transportation
stubborn large area soiling.
Adding the cleaning agent • Switch off the unit before transporting it.
• Draw the cleaning agent suction hose out • To transport it over stairs or obstacles lift
of the housing to the required length. the unit at the transportation handle.
• Hang the cleaning agent suction hose in • To transport the unit over even surfaces
the cleaning agent container. draw it by the drawing bar.
• Rotate the spray lance in the direction of
( ) until reaching the stop.
Cleaning agents
If cleaning agent has been added: For trouble-free operation and for matching
• Hang the cleaning agent suction hose in to the relevant cleaning task we recommend
a container of clear water, switch on the our Kärcher cleaning agents and care range.
unit for about one minute and flush through. Please let us advise you or ask for information
about them. Here is a small selection:
Recommended cleaning method Universal cleaner Profi RM 555 ULTRA
1. Spray the cleaning agent on the dry surface Automobile cleaner Profi RM 565 ULTRA
sparingly and let it react (but not dry out). House and garden cleaner Profi RM 570 ULTRA
2. Wash off the loosened dirt with the high- Boat cleaner Profi RM 575 ULTRA
pressure jet.
Finishing operations
• Master switch to “0”.
• Draw out power plug.
Water supplied from the water main
• Close the water supply tap.
• Separate the unit from the water
connection.
Water supplied from an open container
• Unscrew the suction hose with filter at the
water inlet of the unit.
• Pull the lever on the handgun until the unit
is without pressure.
• Press in the safety ratchet to protect the
unit against inadvertent switching on.
10
Care and Maintenance you detect an excessive leakage, please
contact the authorized customer service.
Cleaning Detergent is not taken in
Before long periods of storage, e.g. in winter: - Clean filter of detergent suction hose
• Pull out the strainer in the water inlet with - Set to low-pressure jet
flat-nose pliers and clean it under running No detergent in high-pressure mode
water. Replacement parts
Maintenance Use exclusively Kärcher original replacement
The unit is maintenance-free. parts. You will find a replacement parts
summary at the end of these operating
Help with faults instructions.
11
Technical Data Special accessories
Circuit Diagram
C1 Capacitor
M1 Motor
Q1 Switch
T Temperature limiter
S1 Pressure switch
12
13
14
15
Karcher Pty Ltd
40 Koornang Road
Scoresby 3179
Victoria, Australia
Tel. 61 3 9765 2300