Sie sind auf Seite 1von 14

updat30.

book Page i Wednesday, March 15, 2000 3:06 PM

<<< Index

PERSONAS86 CURRENCY DISPENSER - STAGE 1

CONTENTS

personaS86
Currency Dispenser - Stage 1

Appendix 17.6A

INTRODUCTION ........................................................................... 17.6A-1

DESCRIPTION................................................................................ 17.6A-4
PRESENTER TRANSPORT SENSORS ...................................... 17.6A-4

STRAPPING .................................................................................... 17.6A-5

ADJUSTMENTS ............................................................................. 17.6A-5

TEST TOOLS .................................................................................. 17.6A-6

INTERNAL CABLES ..................................................................... 17.6A-6


DISPENSER INTERCONNECTION DIAGRAM ....................... 17.6A-7
PRESENTER CABLING ............................................................. 17.6A-8
PRESENTER MOTOR .............................................................. 17.6A-11

TROUBLESHOOTING................................................................. 17.6A-11
DIAGNOSTICS........................................................................... 17.6A-11

17.6A-i
updat30.book Page ii Wednesday, March 15, 2000 3:06 PM

<<< Index

PERSONAS86 CURRENCY DISPENSER - STAGE 1

17.6A-ii
updat30.book Page 1 Wednesday, March 15, 2000 3:06 PM

<<< Index

PERSONAS86 CURRENCY DISPENSER - STAGE 1

CONTENTS

Appendix 17.6-A

personaS86
Currency Dispenser - Stage 1

INTRODUCTION
This appendix to Chapter 17.6 describes the unique features of the
Stage 1 Currency Dispenser in the personaS86 ATM. The Stage 1
dispenser will appear only in the first out personaS86 ATMs and
will be superseded by a dispenser to be known as the personaS86
Currency Dispenser and to be described in a separate chapter of
this publication.
The list below is a guide to which sections of Chapter 17.6
describe the P86 Stage 1 Currency Dispenser:
z Only the Note Thickness Sensor is used
z Only the ASIC Currency Dispenser Control Board is used
z The shutter is mounted on the facia of the P86 ATM (refer to
Chapter 17.3)
z All currency containers are the same
z The pick modules are the same
z The presenter has increased in length but the operation is the
same
z The sensors are as before with the exception of the arrangement
of presenter transport sensors T3, T4, and T5 (described in this
appendix)
z The harnessing arrangement is slightly different (described in
this appendix)
z Diagnostics are the same with the exception of the return from
T6 on the sensor test (described in Chapter ).

17.6A-1
updat30.book Page 2 Wednesday, March 15, 2000 3:06 PM

<<< Index

PERSONAS86 CURRENCY DISPENSER - STAGE 1

The following illustrations show two views of the personaS86


presenter assembly.

Pre LVDT Sensor


Pre LVDT LED
Purge Transport Sensor T1
Clamp Down Sensor

Clamp Up Sensor
Stack Sensor
Purge Overfill Sensor
Purge Bin Microswitch
Purge Overfill LED
and

17.6A-2
updat30.book Page 3 Wednesday, March 15, 2000 3:06 PM

<<< Index

PERSONAS86 CURRENCY DISPENSER - STAGE 1

Present Timing
Disk Sensor

Main Timing Disk


Sensor
T3
T4
T5

17.6A-3
updat30.book Page 4 Wednesday, March 15, 2000 3:06 PM

<<< Index

PERSONAS86 CURRENCY DISPENSER - STAGE 1

DESCRIPTION
The Stage 1 personaS86 (P86) Currency Dispenser uses the 5670
electronics described in the main body of Chapter 17.6. The unique
features of the Stage 1 P86 dispenser is described under the
following headings:
z Presenter Transport Sensors
z Internal Cables
z Diagnostics

PRESENTER TRANSPORT SENSORS


The following illustration shows the location of the sensors and
LEDs throughout the presenter. These are the same as in other
through-the-wall ATMs except for the arrangement of the exit
sensors and LEDs T3, T4 and T5.

Stack Sensor T2

Exit Sensor T5
T4
T3

Purge Overfill
Sensor
Purge Transport Sensor T1

Pre-LVDT Sensor

The sensors T3 and T4 and the LEDs T3, T4, and T5 are
attached to a single bracket as shown in the following illustration.
Sensor T5 is attached to a separate plastic holder between the exit
shafts. The sensors and LEDs are discrete components, each indi-
vidually wired back to the Dispenser Control Board (see “Internal
Cables”).

17.6A-4
updat30.book Page 5 Wednesday, March 15, 2000 3:06 PM

<<< Index

PERSONAS86 CURRENCY DISPENSER - STAGE 1

T4 T3
T5

STRAPPING
The wiring loop between pins 6 and 7 of control board connector J6
identifies the personaS 86 Stage 1 harness to software. See main
chapter for ASIC Dispenser Control Board and Fuse F1.

ADJUSTMENTS
See main chapter for Drive Belt Tension.

17.6A-5
updat30.book Page 6 Wednesday, March 15, 2000 3:06 PM

<<< Index

PERSONAS86 CURRENCY DISPENSER - STAGE 1

TEST TOOLS
None.

INTERNAL CABLES
The following schematic diagrams show the internal cables of the
personaS86 Stage 1 Currency Dispenser. Differences between these
schematics and those for the 56XX Currency Dispenser are:
z Plug number changes in connections to motors
z Transport sensors individually connected to Dispenser Control
Board
z The loop on connector J6 between pins 7 and 8 to identify the
personaS86 Stage 1 harness to software.

NOTE: The pick module connections remain the same and are not
repeated here.

17.6A-6
updat30.book Page 7 Wednesday, March 15, 2000 3:06 PM

<<< Index

PERSONAS86 CURRENCY DISPENSER - STAGE 1

DISPENSER INTERCONNECTION DIAGRAM


AC Interlock Main
P1 SSR P5 Motor

24 V DC Interlock

P Clamp
UNI 10 Motor
DC J1 J13
M1
Present
P9
Motor

Motorized Shutter
J1 Control Board
SDC Bus J2
personaS86 Harness
Detection Loop
Dispenser Control Board

J6 Exit Sensor, Transport Sensors


Purge Overfill (P21), Purge Path (P18)
Pre-LVDT (P14), Stack Sensor (P24)

Exit LED, Transport LEDs, Purge


J3 Overfill LED (P22), Pre-LVDT LED (P16),
Stack LED (P17), Purge LED (P23),
Purge Bin Present Switch (P23)

J4 Timing Disks - Main (P27), Present (P26)


Clamp Sensors, Up (P19) Down (P20)

J8 Note Thickness Sensor

Pick Sensor (P1)


J5 J1 Pick LED (P3)
Pick Interface

Gulp Feed Switch


J2
Solenoid Valve
Pick Arm
Timing Disk (P4)

To Lower Pick
J4
Module I/F (P1)

17.6A-7
updat30.book Page 8 Wednesday, March 15, 2000 3:06 PM

<<< Index

PERSONAS86 CURRENCY DISPENSER - STAGE 1

PRESENTER CABLING (SHEET 1 OF 3)


J3
T5 LED (BLACK)
BL
V V V V V V V V V V
1

V V
T5 LED+ (RED) T5 LED
2 R
T4 LED (BLACK) BL

V V
3 T4 LED
T4 LED+ (RED)
4 R
5 T3 LED (BLACK) BL

V V
T3 LED+ (RED) T3 LED
6 R
PUROF LED Purge
13 2

V V
Overflow
PUROF LED+
14 3 LED P16
PLVDT LED
17 4

V V V
PLVDT LED+ Pre-LVDT
18 1
LED
KEY 3
T2 LED P17
1 Stack
V V V V V V

19
V V

T2 LED+ LED
20 2 P23
Dispenser Control Board

T1LED
15 4
16
T1LED+ V V V V 3 Purge Path
PURGE IN LED and
23 2
Microswitch
GND
24 1

J4 P27
MAIN TD LED-
V V V

1
V V V

4
MAIN TD LED Main
3 2
MAINTD Timing Disk
4 1

P19
CLUP LED-
V V V

5
V V V

4
CLUP LED Clamp Up
7 2
CLAMP UP Sensor
8 1

P26
PRESTD LED-
V V V

9
V V V

4
Present
PRESTD LED
11 2 Timing
PRTDINT- 1 Disk
12

P20
CLDOWN LED-
V V V

13
V V V

4
Clamp
CLDOWN LED
15 2 Down
CLAMPDN Sensor
16 1

17.6A-8
updat30.book Page 9 Wednesday, March 15, 2000 3:06 PM

<<< Index

PERSONAS86 CURRENCY DISPENSER - STAGE 1

PRESENTER CABLING (SHEET 2 OF 3)


J6
TSEN5 E (GREEN)

V V V V V V V V V V V V
G

V V
1 T5
TSEN5 E+ (WHITE) Sensor
2 W
TSEN4 (GREEN) T4
3

V V
G
TSEN4+ (WHITE) Sensor
4 W
5 TSEN3 (GREEN) G

V V
T3
TSEN3+ (WHITE) Sensor
6 W
7
P21
8 LOOP
KEY 4

V V V
Purge
13 PUR OVER Overflow
2
PUR OVER+ Sensor
14 3
TSEN1 P18
15 2
16
TSEN1+ V V V T1 Sensor
3 (Purge Path)
KEY 4 P14
PRE LVDT
V V V V

17 4

V V
Pre-LVDT
PRE LVDT+
18 1 Sensor
TSEN2 P24
19 1
V V

T2 Sensor
TSEN2+ (Stack)
20 4

J13 P9
PRES A+
V V V V

1 1
V V V V

PRES C+
2 2 Presenter
7 PRES B+
3 Motor
PRES D+
8 4

P10
3 CLAMP A+
V V V V

1
V V V V

CLAMP C+
4 2 Clamp
CLAMP B+
9 3 Motor
CLAMP D+
10 4

+5 V
SSR
V V V

5 3
V

6 GND
MOTOR ON-
12 4 SSR
V

17.6A-9
updat30.book Page 10 Wednesday, March 15, 2000 3:06 PM

<<< Index

PERSONAS86 CURRENCY DISPENSER - STAGE 1

PRESENTER CABLING (SHEET 3 OF 3)


J5 J1
CAS ID1-
1C
V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V
1

V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V
2 GND
2
CAS ID2- 3
3
GND 4
4
CAS ID3-
5 5
6 GND
6
CAS ID4-
7 7
GND
8 8
CAS TEMP-
9 9
GND
10 10
CASLOW-
11 11
12 GND
12
13 GULP-
13
LEDON_PICK
14 14
Dispenser Control Board

Pick Interface Board


GND 15
15
GND
16 16
S0
17 17
S1
18 18
DISABLE-
19 19
COILEN-
20 20
PICK
21 21
PSEN1
22 22
PSEN2
23 23
PSEN3
24 24
PSEN4
25 25
PICKTXD
26 26
27 PICK RXD
27
GND
28 28
29 GND
29
+12 V
30 30
+5 V
31 31
+5 V
32 32
GND
33 33
GND
34 34
35 GND
35
36 GND
36
+24 V
37 37
+24 V
38 38
+24 V
39 39
+24 V
40 40

17.6A-10
updat30.book Page 11 Wednesday, March 15, 2000 3:06 PM

<<< Index

PERSONAS86 CURRENCY DISPENSER - STAGE 1

PRESENTER MOTOR

P7
P5A
NEUTRAL
1
V V
1

V V V
Presenter
LIVE SSR/CAP1

V
1 SSR SSR 2 2

V
2
Motor
CAP2
V V 3
3 GROUND Frame
V

V
1
Ground Motor Run
Capacitor

TROUBLESHOOTING
For diagnostic testing refer to the following chapters:
z Level 0 Diagnostics - Chapters 4.2.6 (SDC) and 4.2.17 (Dis-
penser control circuit)
z Level 1 Diagnostics - Chapter 4.3.17
z Level 3 Diagnostics - Chapter 4.4.17

DIAGNOSTICS
In the Level 1 Diagnostics Sensor/Switch Status test the value of
M_DATA returned for Byte 19 (TSEN6) should be greater than
80H. This input detects the personaS86 harness and, therefore, the
dispenser.

17.6A-11
updat30.book Page 12 Wednesday, March 15, 2000 3:06 PM

<<< Index

PERSONAS86 CURRENCY DISPENSER - STAGE 1

17.6A-12

Das könnte Ihnen auch gefallen