Beruflich Dokumente
Kultur Dokumente
COMPETENCY BASED
LEARNING MATERIALS (C B L M)
SECTOR: ELECTRONICS
CBLM
Electronic Product Date Develop: Module:
Assembly Servicing April 16, 2016 Terminating and Connecting
NCII Electrical Wiring and Electronic
Plan Training Session Developed by: Circuit
Version No.1
Joel S. Milan
ACKNOWLEDGEMENT
TESDA Provincial Director, Supervisors and Staff for the scholarship grant
for the trainers’ training in service to the community.
USAT School President, Vice President for Academic Affairs, Vice President
for Personnel and Academic Affairs, Vice President for Finance and
Administrators for the unwavering support and inspiring the EPAS
Administrators and faculty to excel in their field of specialization.
La Salle Tech TM1 Trainers, facilitators, and staff for the patience and
endurance in coaching and mentoring the trainees for the completion of all
the requirements.
Our beloved family for the encouragement, love and care for believing in us
that we can make it.
And finally to almighty God for the endless love, provision, strength and
sustaining powers and for making the impossible possible.
Joel S. Milan
CBLM
Electronic Product Date Develop: Module:
Assembly Servicing April 16, 2016 Terminating and Connecting
NCII Electrical Wiring and Electronics
Plan Training Session Developed by: Circuit
Page |1
Joel S. Milan
HOW TO USE THIS COMPETENCY- BASED LEARNING
MATERIALS
Welcome!
Remember to:
Read information sheets and complete the self-checks. Suggested
References are included to supplement the materials provided in this
Module. Perform the Task Sheets and Job Sheets until you are confident
that your outputs conform to the Performance Criteria Checklist that
Follows the sheets. Submit outputs of the Task Sheets and Job Sheets to
your facilitator For evaluation and recording in the Accomplishment Chart.
Outputs shall serve as your portfolio during the Institutional Competency
Evaluation. When you feel confident that you have had sufficient
Practice, asks your trainer to evaluate you. The results of your
Assessment will be recorded in your Progress Chart and
Accomplishment Chart. You must pass the Institutional Competency
Evaluation for this Competency before moving to another competency. A
Certificate of Achievement will be awarded to you after passing the
evaluation. You need to complete this module before you can perform the
module On Facilitating Learning Sessions.
CBLM
Electronic Product Date Develop: Module:
Assembly Servicing April 16, 2016 Terminating and Connecting
NCII Electrical Wiring and Electronics
Plan Training Session Developed by: Circuit
Page |2
Joel S. Milan
Consumer Electronics Servicing NCII
COMPETENCY-BASED LEARNING MATERIALS
List of Competencies
ELC315202
1. Apply quality standards Applying quality standards
ELC724201
5. Use hand tools Using hand tools
CBLM
Electronic Product Date Develop: Module:
Assembly Servicing April 16, 2016 Terminating and Connecting
NCII Electrical Wiring and Electronics
Plan Training Session Developed by: Circuit
Page |3
Joel S. Milan
Table of Contents
Cover page
Acknowledgement………………………………………………………..… i
Learning Experiences…………………………………………………….4-5
Self-Check 5.5-1
Answer Key 5.5-1
Task Sheet 5.5-1
Performance Criteria Checklist 5.5-1
CBLM
Electronic Product Date Develop: Module:
Assembly Servicing April 16, 2016 Terminating and Connecting
NCII Electrical Wiring and Electronics
Plan Training Session Developed by: Circuit
Page |4
Joel S. Milan
UNIT OF COMPETENCY: Terminate and Connect Electrical Wiring and
Electronics Circuit
QUALIFICATION LEVEL: NC II
INTRODUCTION:
CBLM
Electronic Product Date Develop: Module:
Assembly Servicing April 16, 2016 Terminating and Connecting
NCII Electrical Wiring and Electronics
Plan Training Session Developed by: Circuit
Page |5
Joel S. Milan
SUMMARY OF LEARNING OUTCOMES:
CBLM
Electronic Product Date Develop: Module:
Assembly Servicing April 16, 2016 Terminating and Connecting
NCII Electrical Wiring and Electronics
Plan Training Session Developed by: Circuit
Page |6
Joel S. Milan
Learning Outcome # 05
CONTENTS:
Assessment Criteria:
CBLM
Electronic Product Date Develop:
Assembly Servicing Module:
April 16, 2016
NCII Terminating and Connecting
Electrical Wiring and Electronics
Plan Training Session Developed by: Circuit
Page |2
Joel S. Milan
CONDITIONS:
METHODOLOGIES:
Lecture/discussion
Demonstration
Self-paced instructions
ASSESSMENT METHODS:
Written test
Practical test
Direct observation
CBLM
Electronic Product Date Develop:
Assembly Servicing Module:
April 16, 2016
NCII Terminating and Connecting
Electrical Wiring and Electronics
Plan Training Session Developed by: Circuit
Page |3
Joel S. Milan
Learning Experiences
Learning Outcome:
Conduct Test
Learning Activities Special Instructions
1. Read Information Sheet 1.2-1 for Plan and Read and understand
prepare for tasks to be undertaken, equipments the information sheet
and testing instruments the page 6-15 in CBLM and Check yourself by
2. Answer Self-Check 1.2-1 in CBLM page 16 answering the Self-
Compare your answers with Answer Key 1.2-1 Check. You must answer
page 17 in CBLM all questions correctly
3. Do Task Sheet 1.2-1 Plan and prepare for before proceeding to the
tasks to be undertaken, equipments and testing next activity
instruments page 18 of the CBLM
4. Do performance Criteria Checklist 1.2-1Plan
and prepare for tasks to be undertaken ,
equipments and testing instruments page 19 Job Sheet /Operation
5. Read Information sheet 1.2-2 in CBLM Sheet will help you
(Prepare hand tools) pages 20-26
practice your skills on
6. Answer Self-Check 1.2-2 page 27 of the the particular learning
CBLM Compare your answers with answer key outcome completed
1.2-2 page 28
7. Do Task Sheet 1.2-2 Prepare hand tools page
29 of the CBLM
8. Do Performance Criteria Checklist 1.2-2 The Performance Criteria
Prepare hand tools page 30 of the CBLM Checklist will guide and
help you evaluate your
work as you are
9. Read Information Sheet 1.2-3 for Use
practicing your skill
appropriate hand tools and test equipment
pages 31-35 in CBLM
10. Answer Self-Check 1.2-3 page 36 in CBLM
Compare answers to Answer Key 1.2-3 page 37 Evaluate your own work
in CBLM
using Performance
11. Perform Task Sheet 1.2-3 (Use appropriate Criteria. When you are
hand tools and test equipment) of the CBLM
ready, present your work
page 38
to your trainer for final
12. Do Performance Criteria Checklist 1.2-3
(Use appropriate hand tools and test equipment) evaluation and
of the CBLM page 39 recording. Your output
13. Read Information Sheet 1.2-4 for Maintain shall serve as one of your
hand tools pages 40-49 in CBLM portfolio for Using Hand
Tools
14. Answer Self-Check 1.2-4 page 50 in CBLM
Compare answers to Answer Key 1.2-4 pages 51
in CBLM
15. Perform Task Sheet 1.2-4 (Maintain hand
tools)of the CBLM page 52