Beruflich Dokumente
Kultur Dokumente
Method of Procedure
Table of contents
1. Document History..............................................
History.............................................................................
..........................................................................................
.............................................3
..............3
2. Content............................................................................................
Content...............................................................................................................4
................4
3. Recommended SW………………………………………………………………………..4
4. Prerequisites...................................................................................
Prerequisites.......................................................................................................
..................5
................5
5. WBTS C&I and WN_9.1_2 WN_9.1_2.0
_9.1_2.0 Upgrade Procedure
................................
.........................................
.....................5
.........5
Test.......................................................................
6. IP Connectivity Test.................................................................... ....
...................28
...............28
7. Final check ......................................................................................
.......................................................................................................
.................30
.................30
1. Document History
2. Content
Purpose of this document is to provide the procedure to be followed for WBTS
Commissioning and Integration also Actual WBTS software Upgrade on filed.
This procedure should be practiced as standard process for the said task. However there
may be deviation from the sequence or steps depending upon observation, system
configuration and its behavior during the activity performed. So please read each comment
carefully before proceeding to further step.
3. Recommended SW
BTSSiteEM--WN91
WBTS Site Manager Ver.: BTSSiteEM WN91--1408_055_00
4. Prerequisites
Tools Required:
Required:-
equired:-
a. Pre-
Pre-Check
Hardware Installed as per site Requirement*
Requirement*
i.e.: FSMF, FRGT
FRGT**, FXDB*
FXDB*, FBBA*
FBBA* etc.
etc.
Routing of Optical Cable between SM & RF module done as
per standard.
SFP Installed in FSMF, FRGT, FXDB, FBBA Module should be
greater than or equal to 6 Gig and should be of 850 nm.
nm.
b. Precaution
RF Optical cable shouldn’t bent & shouldn’t tightly tighten
with tie.
Jumper cable should be connected properly on RF Port.
d. SW Upgrade.
Step: - 5.1.
5.1.1
Step: - 5.1.
5.1.2
Install
Install the BTS Site Manager of WN_8.0_4.1 & WN_9.1_1.0 after the new
hardware is ready for power on.
Open BTS Manager and insert Credential and click connect.
Step: - 5.1.
5.1.3
Verify the factory version is correct and applicable as per Below Upgrade
path.
Step: - 5.1.4
On BTS Manger Click on software Tab
Tab-- Update SW to
BTS Site
Note:
Note: - Once Upgrade started please insure Laptop Power & LAN connection should not disconnect
at any stage during complete upgrade.
In next ~2-
~2-3 Minutes both System ModuleModule (FSMF) and RF
Module (FRGT/FXD
(FRGT/FXDB)B) will be visible on BTS manager, Please
Verify the Installed number of RF module should appeared
on window.
Step: - 5.1.
5.1.5
SW upgrade again for target build when BTSSM is
reporting the “Incompatible SW version detected (0023)”
Note: In this step, only the RF Module software is downloaded,
downloaded, it’s only to
reset RF and no need to reset BTS.
Re-
Re-Upgrade wil
willl take ~2 Minute to Upgrade RF Module.
Module.
Click Close once Upgarde has completed.
Step: - 5.1.7
Select the port speed ( It may vary according to the Transmission Port BW
(1Gig/100Mbit/s/10 Mbit/s) of FSM.
Step: - 5.1.8
Step: - 5.1.9
Define Far end SCTP subnet as per planning sheet along with
SCTP Port no. & all parameters as shown below.
Step: - 5.1.10
Step: - 5.1.11
Step: - 5.1.11
Step: - 5.1.12
Step: - 5.1.13
Note: Each Site can have different License as per site config same can be asked
from RF team.
Step: - 5.1.14
Step: - 5.1.15
Step: - 5.1.16
Step: - 5.1.17
Step: - 5.1.18
Step: - 5.1.19
Step: - 5.1.20
Step: - 5.1.21
Please Check
Check,, there shouldn’t be any alarm on
on Alarm
window post site on-on-air.
If there is any alarm please clear it accordingly.
accordingly.
6 IP Connectivity Test
Please verify All configured Host IP’s are reachable by Below
Process.
Click on Tests IP Connectivity Test
New window will appear, select All Configured host and click
start.
If all Hosts are reachable then in Test Result it’ll show Connected and if
any of host is not reachable then it’ll show “Not connected”.
Also if need to ping any specific i.e. gateway IP, then Insert the
IP of gateway on address Box and select source address and
check the Test Result.
7 Final check
Ensure there is no alarm in BTS manager before leaving from site.
Ensure you have taken the Complete Snapshot of current BTS
configuration.
Before removing LAN cable from LMP port make sure the BTS Site
Manger has been closed properly.
*At last FSMF Box has packed with TOP Cover and screws have
tightened as required.
Note: License quantity & all features must be confirmed from RF team before
putting them in SCF file.
Thank You