Beruflich Dokumente
Kultur Dokumente
ANALOG (HTTPS://CIRCUITDIGEST.COM/ANALOG-ELECTRONICS)
Water tank over ow is a common problem which leads to the wastage of water. Though there are many solutions to it like ball valves which automatically
stop the water ow once the tank gets full. But being an electronics enthusiastic wouldn’t you like an electronic solution for it? So here is a simple and
handy DIY that will guide you to make a circuit which will detect the water level and will raise an alarm upon getting the water tank full or a preset level.
SPONSORED SEARCHES
Circuit PCB
Level Measurement
https://circuitdigest.com/electronic-circuits/water-level-indicator-alarm-circuit 1/23
11/28/2018 Simple Water Level Indicator Alarm Circuit Diagram
This simple transistor based water level indicator circuit is very useful to indicate the water levels in a tank. Whenever tank gets lled, we get alerts on
particular levels. Here we have created 4 levels (low, medium, high and full), we can create alarms for more levels. We have added 3 LEDs to indicate initial
three levels (A, B, C), and one Buzzer to indicate FULL level (D). When tanks gets lled completely we get beep sound from Buzzer.
Circuit Components
4 - BC547 transistors
6 - 220 ohm resistors
3 - Colour led
1 – Buzzer
5 - 9v battery + battery clip
Circuit Diagram
SPONSORED SEARCHES
Electronic Circuit
Level Measurement
(http://circuitdigest.com/fullimage?i=circuitdiagram/Water-Level-Indicator-Alarm.gif)
We can consider this whole circuit as 4 small circuits, each one for indicating/alarming, when a particular level (A,B,C,D) of water have been reached.
When water level reaches to point A, circuit with RED LED & transistor Q1 gets completed and RED LED glows. Similarly when water level reaches to point
B, circuit with YELLOW LED and transistor Q2 gets completed and Yellow LED glows, same goes with point C. And nally when tank gets full (Point D),
circuit with buzzer gets completed and buzzer starts beeping.
Working
Here we are using transistor (of NPN type) as a Switch. Initially there is no voltage applied to the base of the Transistor Q1 and the transistor is in OFF
state and no current is owing through collector and emitter and LED is OFF (See below diagram to understand Transistor Pin structure).
https://circuitdigest.com/electronic-circuits/water-level-indicator-alarm-circuit 2/23
11/28/2018 Simple Water Level Indicator Alarm Circuit Diagram
SPONSORED SEARCHES
Level Gauge
Water Detector
Water System
When the water level reaches to Point A in the tank, the positive side of the battery gets connected to the base of the Transistor Q1 through the water. So
when a positive voltage has been applied to the base of the Transistor Q1, it gets into ON state and current starts owing from collector to emitter. And
RED LED glows.
You can see resistors (R1, R2, R3) at the base of each transistor, which is used to limit the maximum Base current. Generally a transistor gets its ON state
fully when a voltage of 0.7 V is applied to the base. There are also resistors (R4, R5, R6) with each of the LEDs, to drop the voltage across LEDs, otherwise
LED may blow up.
Same phenomenon happens when water level reaches to Point B. As soon as water level reaches to Point B, a positive voltage gets applied to the
Transistor Q2, it gets ON and current started owing through YELLOW LED, and LED glows. With same principle, GREEN LED glow when water level
reaches to Point C.And nally Buzzer beeps when water level reaches to D.
Note that Left most wire in the tank must be lengthier than other four wires in the tanks, because this is the wire which is connected to positive voltage.
Video
https://circuitdigest.com/electronic-circuits/water-level-indicator-alarm-circuit 3/23
11/28/2018 Simple Water Level Indicator Alarm Circuit Diagram
JLCPCB Prototype: Only $2 for 10 pcs PCBs, 48 Hours Quick Turn (https://jlcpcb.com/)
JLCPCB, with 300,000+ Customers Worldwide, 8,000+ PCB Orders Per Day. (https://jlcpcb.com)
Email Address *
Name
Country
United States of America
https://circuitdigest.com/electronic-circuits/water-level-indicator-alarm-circuit 4/23
11/28/2018 Simple Water Level Indicator Alarm Circuit Diagram
Subscribe
PREVIOUS POST
Transistor Tester using 555 Timer IC (https://circuitdigest.com/electronic-circuits/transistor-tester)
NEXT POST
One Bit Memory Cell (https://circuitdigest.com/electronic-circuits/one-bit-memory-cell)
COMMENTS
Yashaswi
Nov 16, 2015
mahantesh angadi
Oct 08, 2016
Joy Biswas
Apr 21, 2017
can i use this water lavel indecator for 500 liter tank ?
Log in (/user/login?destination=node/14%23comment-form) or register (/user/register?destination=node/14%23comment-form)
to post comments
Ankit
Oct 18, 2016
Kalaimani
Feb 02, 2017
linkan
Oct 31, 2017
its a demo project...if u will make a large base project then it will work....bt d concept z same...
Log in (/user/login?destination=node/14%23comment-form) or register (/user/register?destination=node/14%23comment-form) to
post comments
Jayant (/users/jayant)
Nov 21, 2015
(/users/jayant)
Of course, it will work, but you need a proper installation.
Log in (/user/login?destination=node/14%23comment-form) or register (/user/register?destination=node/14%23comment-form) to post
comments
kelly
Nov 26, 2015
https://circuitdigest.com/electronic-circuits/water-level-indicator-alarm-circuit 5/23
11/28/2018 Simple Water Level Indicator Alarm Circuit Diagram
Log in (/user/login?destination=node/14%23comment-form) or register (/user/register?destination=node/14%23comment-form) to post
comments
Jayant (/users/jayant)
Nov 28, 2015
(/users/jayant)
We are already using BC547 transistor, any General Purpose small signal NPN transistor should work here.
Log in (/user/login?destination=node/14%23comment-form) or register (/user/register?destination=node/14%23comment-form) to
post comments
Prakash Koppal
Nov 03, 2016
ya you can use ....or any other general purpose transistors also
Log in (/user/login?destination=node/14%23comment-form) or register (/user/register?destination=node/14%23comment-form) to
post comments
uk
Nov 29, 2015
Sir may I use it in my 1500L tank .. Will it woperfectly ? And me fast sir.
Log in (/user/login?destination=node/14%23comment-form) or register (/user/register?destination=node/14%23comment-form) to post
comments
Jayant (/users/jayant)
Dec 05, 2015
(/users/jayant)
As previously stated, it will de nitively work in any tank but you need a proper installation, concept will
Log in (/user/login?destination=node/14%23comment-form) or register (/user/register?destination=node/14%23comment-form) to
post comments
remain the same.
pankaj
Dec 19, 2015
Sir, why not you have used resistor with the transister connected with the buzzer?
Log in (/user/login?destination=node/14%23comment-form) or register (/user/register?destination=node/14%23comment-form) to post
comments
Maddy (/users/maddy)
Jan 01, 2016
(/users/maddy)
Yes, you can also use current limiting Resistor for the forth Transistor, to prevent it from any kind of
Log in (/user/login?destination=node/14%23comment-form) or register (/user/register?destination=node/14%23comment-form) to
post comments
damage.
Priyanka
Dec 27, 2015
Sir, will it work with long wires like from terrace to room
Log in (/user/login?destination=node/14%23comment-form) or register (/user/register?destination=node/14%23comment-form) to post
comments
Maddy (/users/maddy)
Jan 01, 2016
(/users/maddy)
yes
Log in (/user/login?destination=node/14%23comment-form) or register (/user/register?destination=node/14%23comment-form) to
post comments
Lihan
Jan 30, 2016
Yes
Log in (/user/login?destination=node/14%23comment-form) or register (/user/register?destination=node/14%23comment-form) to
post comments
https://circuitdigest.com/electronic-circuits/water-level-indicator-alarm-circuit 6/23
11/28/2018 Simple Water Level Indicator Alarm Circuit Diagram
Raj
Sep 10, 2016
sourav shome
Mar 21, 2017
pragya
Jan 29, 2016
mish
Oct 09, 2016
hi same thing happening with me too. I made 2 circuits and 1 led glowed when i connected with the battery and with the
Log in (/user/login?destination=node/14%23comment-form) or register (/user/register?destination=node/14%23comment-form) to
post comments
2nd circuit the buzzer is buzzing without pouring water. The circuit looks right but idk what the problem is? Can you help please.
Thanks
hemantdhakad
Jan 29, 2016
Sir
Log in (/user/login?destination=node/14%23comment-form) or register (/user/register?destination=node/14%23comment-form) to post
comments
I am making your project but sir me use transistor bc548 so sir any problem
Please rply
Maddy (/users/maddy)
Feb 08, 2016
(/users/maddy)
yes, you can use bc548.
Log in (/user/login?destination=node/14%23comment-form) or register (/user/register?destination=node/14%23comment-form) to
post comments
sandy
Jan 29, 2016
its super
Log in (/user/login?destination=node/14%23comment-form) or register (/user/register?destination=node/14%23comment-form) to post
comments
muzzammil
Feb 06, 2016
i want to attach buzzer on each LED then what should i do, please guid...
Log in (/user/login?destination=node/14%23comment-form) or register (/user/register?destination=node/14%23comment-form) to post
comments
thx
https://circuitdigest.com/electronic-circuits/water-level-indicator-alarm-circuit 7/23
11/28/2018 Simple Water Level Indicator Alarm Circuit Diagram
Maddy (/users/maddy)
Feb 08, 2016
(/users/maddy)
you can directly connect Buzzers with LEDs.
Log in (/user/login?destination=node/14%23comment-form) or register (/user/register?destination=node/14%23comment-form) to
post comments
Cesar
Feb 10, 2016
Sir
Log in (/user/login?destination=node/14%23comment-form) or register (/user/register?destination=node/14%23comment-form) to post
comments
How long is the maximum distance in meters form a 5 volts or 9 volts battery ? Like with an UTP network cable.
vineet
Feb 12, 2016
Dear Sir,
Log in (/user/login?destination=node/14%23comment-form) or register (/user/register?destination=node/14%23comment-form) to post
comments
My query is that I want to install the system at ground oor and put the wires in the water tank located on second oor. For that I
have to pull the wires for approximately 40 feet . So for such a long length wouldn't there be copper losses and would it function
with 9V battery
Jayant (/users/jayant)
Mar 11, 2016
(/users/jayant)
The voltage drop is dependent upon the resistance of wire, load resistance and current through the wire.
Log in (/user/login?destination=node/14%23comment-form) or register (/user/register?destination=node/14%23comment-form) to
post comments
But roughly according to this circuit, we can use it upto 100-150 feets. You can check some online voltage drop calculators to
nd the accurate length according to your wire.
vikram shetty
Feb 27, 2016
Sir as on 28 Feb we are celebrating science day I am going to exhibit this model but sir.... Asci have tested once I observed
Log in (/user/login?destination=node/14%23comment-form) or register (/user/register?destination=node/14%23comment-form) to post
comments
that the Buzzer will not scream loudly as it just sounds in small amount only like a whistle. so myvdoubt is ... Is this buzzer will be
able to warn the person.... Plz reply
Jayant (/users/jayant)
Mar 11, 2016
(/users/jayant)
You can either use some Alarm with external power supply and transistor as a trigger or You can use AC
Log in (/user/login?destination=node/14%23comment-form) or register (/user/register?destination=node/14%23comment-form) to
post comments
alarm with a Relay in place of Buzzer. Check How to use Relay here (http://circuitdigest.com/electronic-circuits/automatic-
room-lights-using-pir-sensor-and-relay).
Siyam
Mar 22, 2016
Hi, I have made this water level indicator but it is not working properly because the water is not connecting the wires inside it.
Log in (/user/login?destination=node/14%23comment-form) or register (/user/register?destination=node/14%23comment-form) to post
comments
However when I put salt in the water it works. If possible help me in this issue.
Jayant (/users/jayant)
Mar 29, 2016
(/users/jayant)
https://circuitdigest.com/electronic-circuits/water-level-indicator-alarm-circuit 8/23
11/28/2018 Simple Water Level Indicator Alarm Circuit Diagram
Log in (/user/login?destination=node/14%23comment-form) or register (/user/register?destination=node/14%23comment-form) to
post comments
Probably you are using Puri ed Water or Distilled Water, which does not conduct electricity. And after adding salt (ionized
substances), it becomes conductor.
Naseer Hakeem
Mar 26, 2016
ankit tomer
Mar 29, 2016
sir, i have completed this project on pcb board with proper designing of pcb.but the problem is that not even a single LED is
Log in (/user/login?destination=node/14%23comment-form) or register (/user/register?destination=node/14%23comment-form) to post
comments
glowing.can you please suggest where may be the fault??
and sir i have connected the base of the transistor to the sensor,emitter to -ve termonal of battery and collector to LED.Is it
right,sir??
Jayant (/users/jayant)
Mar 29, 2016
(/users/jayant)
This is a very simple circuit and should work without any issue, have you connected LED terminals properly
Log in (/user/login?destination=node/14%23comment-form) or register (/user/register?destination=node/14%23comment-form) to
post comments
according to polarity.
Sunny Yadav
Mar 29, 2016
Hasan
Apr 01, 2016
Sir,
Log in (/user/login?destination=node/14%23comment-form) or register (/user/register?destination=node/14%23comment-form) to post
comments
Can I use motor by replacing the buzzer ??
Is any possibilities here when the water will have reached the top of the tank then the motor will off??
I mean the pump motor which is using to enlarge the water level of the tank!!
Can I use motor by replacing the buzzer ??
Abhishek (/users/abhishek)
Apr 02, 2016
(/users/abhishek)
@Hasan and @Sunny Yes you can use Pump motor. A Relay will be used for this. To switch Off the
Log in (/user/login?destination=node/14%23comment-form) or register (/user/register?destination=node/14%23comment-form) to
post comments
motor, use Relay with PNP transistor and to switch On the motor use Relay with NPN transistor. Check this for Relay
connections (http://circuitdigest.com/electronic-circuits/remote-controlled-light-switch).
amit
Apr 02, 2016
https://circuitdigest.com/electronic-circuits/water-level-indicator-alarm-circuit 9/23
11/28/2018 Simple Water Level Indicator Alarm Circuit Diagram
Log in (/user/login?destination=node/14%23comment-form) or register (/user/register?destination=node/14%23comment-form) to post
comments
Vikas
Apr 02, 2016
Why do we need the transistor, i know that it works as a switch here, but what happens if i directly connect the led cathode to
Log in (/user/login?destination=node/14%23comment-form) or register (/user/register?destination=node/14%23comment-form) to post
comments
the wire and drop it into the water instead of connecting the transistor? Theoretically it will work, but what happens if I implement it
practically?
Abhishek (/users/abhishek)
Apr 17, 2016
(/users/abhishek)
Water is not a perfect conductor, but it can conduct enough to trigger Transistors to Glow LEDs. Hence
Log in (/user/login?destination=node/14%23comment-form) or register (/user/register?destination=node/14%23comment-form) to
post comments
Transistor is also used here as Ampli ers.
Shubham Sawant
May 27, 2017
You can do this by increasing current of supply by using mobile charger or else and check with multimeter to nd excess
Log in (/user/login?destination=node/14%23comment-form) or register (/user/register?destination=node/14%23comment-form) to
post comments
voltage to use appropriate resistor.
I have made such a working circuit and using it in perfect working condition.
Sunaabh Sarkar
Oct 30, 2017
Most mobile chargers are small SMPS devices that reduce the mains voltage to 5.1v etc etc, and usually there is no
Log in (/user/login?destination=node/14%23comment-form) or register (/user/register?destination=node/14%23comment-form)
to post comments
isolation of the mains from the output, so one runs the risk of electrocution if a mobile charger is used to run the device so a
mobile charger would not be a good idea to power the device. Use a 9v battery or a power supply using s step down
transformer... the battery eliminator kind of thing.
venkatesh
Jun 29, 2018
conductivity of water is less compared to conductor.power loss is acquired in water so it not enough for gloving led.we are
Log in (/user/login?destination=node/14%23comment-form) or register (/user/register?destination=node/14%23comment-form) to
post comments
using trasister required 0.7v input for switching transister.
anusha
Apr 03, 2016
Sir ,What happens if we change the resistor values?? And can i replace the buzzer with an 8 ohm speaker.if yes shall i need to
Log in (/user/login?destination=node/14%23comment-form) or register (/user/register?destination=node/14%23comment-form) to post
comments
connect resistor at fouth trasistor also??
Abhishek (/users/abhishek)
Apr 17, 2016
(/users/abhishek)
You can use Speaker with some musical IC, check this circuit Siren Generator Circuit
Log in (/user/login?destination=node/14%23comment-form) or register (/user/register?destination=node/14%23comment-form) to
post comments
(http://circuitdigest.com/electronic-circuits/um3561-siren-generator-circuit). And search more circuits on Speaker on this site.
https://circuitdigest.com/electronic-circuits/water-level-indicator-alarm-circuit 10/23
11/28/2018 Simple Water Level Indicator Alarm Circuit Diagram
Joe Jose
Apr 07, 2016
Hi, I have made this water level indicator but it is not working properly because the water is not conducting elecyricity. If
Log in (/user/login?destination=node/14%23comment-form) or register (/user/register?destination=node/14%23comment-form) to post
comments
possible help me in this issue.
neel gohel
Apr 08, 2016
Abhishek (/users/abhishek)
Apr 17, 2016
(/users/abhishek)
@Joe: Check above comments for Water conductivity problem.
Log in (/user/login?destination=node/14%23comment-form) or register (/user/register?destination=node/14%23comment-form) to
post comments
@neel: Yes you can use BC548 and 470 Ohm resistor
mahi
Apr 11, 2016
Gopi
Apr 13, 2016
Shanmuk
Apr 15, 2016
May I get single led glow at particular level.if possible can you suggest me sir.as I am facing di culty with that.
Log in (/user/login?destination=node/14%23comment-form) or register (/user/register?destination=node/14%23comment-form) to post
comments
som
Apr 15, 2016
Dear,
Log in (/user/login?destination=node/14%23comment-form) or register (/user/register?destination=node/14%23comment-form) to post
comments
The buzzer will produce a steady sound. Instead of that, if I need to sound like a siren, then how I can achieve this. I assume some
capacitor/resistor may solve the problem. But I don't know how to connect those components to the base of the transistor.
som
Apr 15, 2016
Dear - How to make the buzzer sound like a siren instead of just producing a steady sound?
Log in (/user/login?destination=node/14%23comment-form) or register (/user/register?destination=node/14%23comment-form) to post
comments
Abhishek (/users/abhishek)
Apr 17, 2016
(/users/abhishek)
Check this circuit: Melody or Sound Generator Circuit (http://circuitdigest.com/electronic-
circuits/melody-sound-generator-circuit)
https://circuitdigest.com/electronic-circuits/water-level-indicator-alarm-circuit 11/23
11/28/2018 Simple Water Level Indicator Alarm Circuit Diagram
Log in (/user/login?destination=node/14%23comment-form) or register (/user/register?destination=node/14%23comment-form) to
post comments
falesh
Apr 16, 2016
Can I increase the no of LED indicators to 7 by repeating the Transistor circuit 4 more times?
Log in (/user/login?destination=node/14%23comment-form) or register (/user/register?destination=node/14%23comment-form) to post
comments
Abhishek (/users/abhishek)
Apr 17, 2016
(/users/abhishek)
yes
Log in (/user/login?destination=node/14%23comment-form) or register (/user/register?destination=node/14%23comment-form) to
post comments
Yogendra Singh
Apr 19, 2016
hello
Log in (/user/login?destination=node/14%23comment-form) or register (/user/register?destination=node/14%23comment-form) to post
comments
i made the circuit according to above shown gure but i connect mobile charger as a source in place of 9v battery all LEDs works
ne but there is problem with buzzer there is no sound from it when i complete circuit by dropping wires in water tank but it works
ne if i connect wire directly..
Gayan
Apr 21, 2016
Sir
Log in (/user/login?destination=node/14%23comment-form) or register (/user/register?destination=node/14%23comment-form) to post
comments
How can use this circuit reverse type. Because i wan't measure water level in my water well. Actually I want low level indicator.
Water level is gone down i want indicate the led. How can use this. Pls help me.
Abhishek (/users/abhishek)
May 06, 2016
(/users/abhishek)
Use PNP transistor BC557 in place of BC547 and reverse the order of LED/buzzer.
Log in (/user/login?destination=node/14%23comment-form) or register (/user/register?destination=node/14%23comment-form) to
post comments
Lokesh
Apr 26, 2016
Aju mallik
Apr 29, 2016
Thanks sir.
Log in (/user/login?destination=node/14%23comment-form) or register (/user/register?destination=node/14%23comment-form) to post
comments
Tahir Aleem
May 04, 2016
sir which type of transistor we are using in this project i mean pnp or npn???
Log in (/user/login?destination=node/14%23comment-form) or register (/user/register?destination=node/14%23comment-form) to post
comments
Maddy (/users/maddy)
May 17, 2016
https://circuitdigest.com/electronic-circuits/water-level-indicator-alarm-circuit 12/23
11/28/2018 Simple Water Level Indicator Alarm Circuit Diagram
NPN
(/users/maddy)
adithya
May 12, 2016
Maddy (/users/maddy)
May 17, 2016
(/users/maddy)
This demo project can be made in less than 100 Rupees.
Log in (/user/login?destination=node/14%23comment-form) or register (/user/register?destination=node/14%23comment-form) to
post comments
Junaid
May 17, 2016
The circuit is complete when voltage ows through the water.. But if the voltage ows, then the current may also ow. So, if I
Log in (/user/login?destination=node/14%23comment-form) or register (/user/register?destination=node/14%23comment-form) to post
comments
use it for my houses tank, would current owing in the water be a problem, or the water does not get electrocuted, please do give
me a quick and su cient answer.
Thanks.
Maddy (/users/maddy)
Jul 12, 2016
(/users/maddy)
Yes current will ow through the water, but current from 9v battery is not harmful.
Log in (/user/login?destination=node/14%23comment-form) or register (/user/register?destination=node/14%23comment-form) to
post comments
ajithkumar g
May 24, 2016
Dureste
Jun 10, 2016
Thank you for the brie ng man! but is it necessary to use a battery? is there any change that would happen if i apply a bridge
Log in (/user/login?destination=node/14%23comment-form) or register (/user/register?destination=node/14%23comment-form) to post
comments
recti er circuit instead of battery? if yes, do i have to change the resistor value if the output of recti er is 12v?? thanks man.
dharmendra
Jun 13, 2016
Sir.. I complete the ckt. Of water level indicator bt one doubt is that if my tank is full then buzzer will start bt till the level of
Log in (/user/login?destination=node/14%23comment-form) or register (/user/register?destination=node/14%23comment-form) to post
comments
water is full the buzer will operate on for long time so how i can stop to this
https://circuitdigest.com/electronic-circuits/water-level-indicator-alarm-circuit 13/23
11/28/2018 Simple Water Level Indicator Alarm Circuit Diagram
kaushik
Jun 14, 2016
Dear sir,
Log in (/user/login?destination=node/14%23comment-form) or register (/user/register?destination=node/14%23comment-form) to post
comments
How we convert 5-9 V into 220/230V ??
Please tell me...
Bobby
Jul 02, 2016
respected sir
Log in (/user/login?destination=node/14%23comment-form) or register (/user/register?destination=node/14%23comment-form) to post
comments
can i use transformer in place of 9 V battery and motor as buzzer
if yes
what will be connection
Maddy (/users/maddy)
Jul 12, 2016
(/users/maddy)
@kaushik @bobby: yes you can, check our Cell Phone Charger Circuit (http://circuitdigest.com/electronic-
Log in (/user/login?destination=node/14%23comment-form) or register (/user/register?destination=node/14%23comment-form) to
post comments
circuits/cell-phone-charger-circuit-diagram)
Waqas
Jul 10, 2016
For how long will the buzzer sound? I mean, once you are alerted, how can you stop the sound of buzzer? turning the circuit off
Log in (/user/login?destination=node/14%23comment-form) or register (/user/register?destination=node/14%23comment-form) to post
comments
wouldn't be a good idea as it would be in e cient to turn the circuit on and off again.
vipool
Jul 11, 2016
the buzzer used in this ckt is having very low sound . i want to increase the strength of the buzzer or use some other device for
Log in (/user/login?destination=node/14%23comment-form) or register (/user/register?destination=node/14%23comment-form) to post
comments
that purpose. what is the solution for dat?
Maddy (/users/maddy)
Jul 12, 2016
(/users/maddy)
Trigger some 220/110V AC alarm with the help of Relay and be careful while working with 220v, it can be
Log in (/user/login?destination=node/14%23comment-form) or register (/user/register?destination=node/14%23comment-form) to
post comments
lethal.
Muhammed Hussei...
Jul 15, 2016
sandeep
Jul 21, 2016
https://circuitdigest.com/electronic-circuits/water-level-indicator-alarm-circuit 14/23
11/28/2018 Simple Water Level Indicator Alarm Circuit Diagram
Abhishek (/users/abhishek)
Aug 13, 2016
(/users/abhishek)
NO, use 9v volt general purpose battery.
Log in (/user/login?destination=node/14%23comment-form) or register (/user/register?destination=node/14%23comment-form) to
post comments
waleed
Jul 26, 2016
why not we use PNP instead of NPN. let suppose we use PNP what will be the impact on the circuit.
Log in (/user/login?destination=node/14%23comment-form) or register (/user/register?destination=node/14%23comment-form) to post
comments
Arun
Jul 29, 2016
Super idea sir...But I have to implement using wireless technique sir..I have an Arduino board..Give me an idea sir
Log in (/user/login?destination=node/14%23comment-form) or register (/user/register?destination=node/14%23comment-form) to post
comments
Abhishek (/users/abhishek)
Aug 13, 2016
(/users/abhishek)
Check this one: Automatic Water Level Indicator and Controller using Arduino
Log in (/user/login?destination=node/14%23comment-form) or register (/user/register?destination=node/14%23comment-form) to
post comments
(http://circuitdigest.com/microcontroller-projects/water-level-indicator-project-using-arduino)
Abhijeet Gawande
Aug 01, 2016
Sir, the circuit is working properly on 9v battery.but I have used a 9v transformer here and seven colors led .the problem is
Log in (/user/login?destination=node/14%23comment-form) or register (/user/register?destination=node/14%23comment-form) to post
comments
that,I am getting the output but the led's a are not blinking and the buzzer is not making proper sound.
Please help.
Abhishek (/users/abhishek)
Aug 13, 2016
(/users/abhishek)
You rst need to have proper 9v regulated power supply from the Transformer, you cant just directly
Log in (/user/login?destination=node/14%23comment-form) or register (/user/register?destination=node/14%23comment-form) to
post comments
connect the Transformer. Check this circuit: Cell Phone Charger Circuit (http://circuitdigest.com/electronic-circuits/cell-phone-
charger-circuit-diagram)
John
Aug 04, 2016
If we add a diode in the forward biased direction anywhere in the circuit, will it change the outcome?
Log in (/user/login?destination=node/14%23comment-form) or register (/user/register?destination=node/14%23comment-form) to post
comments
shiv singh
Aug 24, 2016
Transistor burn when prob short please give the solution of prob short transistor not burn.
Log in (/user/login?destination=node/14%23comment-form) or register (/user/register?destination=node/14%23comment-form) to post
comments
Thanks
shiv singh
waleed sajjad
Aug 24, 2016
https://circuitdigest.com/electronic-circuits/water-level-indicator-alarm-circuit 15/23
11/28/2018 Simple Water Level Indicator Alarm Circuit Diagram
Can anyone tell me how to use buzzer at low level to indicate empty tank?
last » (/electronic-circuits/water-level-indicator-alarm-circuit?page=1)
TI TRAINING VIDEOS
Comprehensive Battery Pack Monitoring for Hybrid & Electric Vehicles (https://ad.doubleclick.net/ddm/clk/427653252;229621325;d?
https://training.ti.com/comprehensive-battery-pack-monitoring-hybrid-electric-vehicles?HQS=sys-null-null-adtrainingseries-asset-tr-
CircuitDigest-in&DCM=yes &https%3A%2F%2Ftraining.ti.com%2Fcomprehensive-battery-pack-monitoring-hybrid-electric-
vehicles%3FHQS=sys-null-null-adtrainingseries-asset-tr-CircuitDigest-in&DCM=yes_)
Ultrasonic Sensing for More Accurate and Precise Water Flow Meters (https://ad.doubleclick.net/ddm/clk/427653252;229621325;d?
https://training.ti.com/ultrasonic-sensing-more-accurate-and-precise-water- ow-meters?HQS=sys-null-null-adtrainingseries-asset-tr-
CircuitDigest-in&DCM=yes &https%3A%2F%2Ftraining.ti.com%2Fultrasonic-sensing-more-accurate-and-precise-water- ow-
meters%3FHQS=sys-null-null-adtrainingseries-asset-tr-CircuitDigest-in&DCM=yes_)
https://circuitdigest.com/electronic-circuits/water-level-indicator-alarm-circuit 16/23
11/28/2018 Simple Water Level Indicator Alarm Circuit Diagram
tr-CircuitDigest-in&DCM=yes &https%3A%2F%2Ftraining.ti.com%2Flevel-1-and-2-ac-charging-pile-station-design-
considerations%3Fcu=1128055&HQS=sys-null-null- owmeter-asset-tr-CircuitDigest-in&DCM=yes_)
LATEST POSTS
SPONSORED
(https://ad.doubleclick.net/ddm/clk/427653252;229621325;d?
https://training.ti.com/comprehensive-battery-pack-monitoring-hybrid-electric-vehicles?HQS=sys-null-null-adtrainingseries-asset-tr-
CircuitDigest-in&DCM=yes &https%3A%2F%2Ftraining.ti.com%2Fcomprehensive-battery-pack-monitoring-hybrid-electric-vehicles%3FHQS=sys-
null-null-adtrainingseries-asset-tr-CircuitDigest-in&DCM=yes_)
Comprehensive Battery Pack Monitoring for Hybrid & Electric Vehicles (https://ad.doubleclick.net/ddm/clk/427653252;229621325;d?
https://training.ti.com/comprehensive-battery-pack-monitoring-hybrid-electric-vehicles?HQS=sys-null-null-adtrainingseries-asset-tr-
CircuitDigest-in&DCM=yes &https%3A%2F%2Ftraining.ti.com%2Fcomprehensive-battery-pack-monitoring-hybrid-electric-vehicles%3FHQS=sys-
null-null-adtrainingseries-asset-tr-CircuitDigest-in&DCM=yes_)
(/microcontroller-projects/arm7-lpc2148-adc-tutorial-to-measure-
analog-voltage)
How to use ADC in ARM7 LPC2148 - Measuring Analog Voltage (/microcontroller-projects/arm7-lpc2148-adc-tutorial-to-measure-analog-
voltage)
https://circuitdigest.com/electronic-circuits/water-level-indicator-alarm-circuit 17/23
11/28/2018 Simple Water Level Indicator Alarm Circuit Diagram
(/electronic-circuits/single-transistor-audio-mixer-circuit)
(/news/secora-pay-w-turns-fashion-wearables-into-payment-devices)
In neon’s SECORA™ Pay W turns fashion wearables into payment devices (/news/secora-pay-w-turns-fashion-wearables-into-payment-devices)
(/news/iot-asset-management-solution-pinpoint-and-track-cars-for-
vehicle-lot-operators)
New IoT Asset Management Solution Pinpoints and Tracks Cars for Vehicle Lot Operators (/news/iot-asset-management-solution-pinpoint-and-
track-cars-for-vehicle-lot-operators)
(/article/all-you-want-to-know-about-electric-vehicle-batteries)
https://circuitdigest.com/electronic-circuits/water-level-indicator-alarm-circuit 18/23
11/28/2018 Simple Water Level Indicator Alarm Circuit Diagram
(/news/32-bit-rx66t-mcu-for-motor-control-in-industrial-home-
appliances-and-robotics)
32-Bit RX66T MCU for Motor Control in Industrial, Home Appliance, and Robotics Devices (/news/32-bit-rx66t-mcu-for-motor-control-in-
industrial-home-appliances-and-robotics)
In neon’s SECORA™ Pay W turns fashion wearables into payment devices (/news/secora-pay-w-turns-fashion-wearables-into-payment-
devices)
(/news/secora-
pay-w-turns-
fashion-
wearables-
into-payment-
devices)
New IoT Asset Management Solution Pinpoints and Tracks Cars for Vehicle Lot Operators (/news/iot-asset-management-solution-
pinpoint-and-track-cars-for-vehicle-lot-operators)
(/news/iot-
asset-
management-
solution-
pinpoint-and-
track-cars-for-
vehicle-lot-
operators)
32-Bit RX66T MCU for Motor Control in Industrial, Home Appliance, and Robotics Devices (/news/32-bit-rx66t-mcu-for-motor-control-in-
industrial-home-appliances-and-robotics)
(/news/32-bit-
rx66t-mcu-for-
motor-
control-in-
industrial-
home-
appliances-
and-robotics)
(/news/ultra-
low-power-
omnipolar-
hall-effect-
sensors)
Tiny MEMS Pressure Sensor Enhances Measurement Accuracy and Avoids Time-Consuming Calibration (/news/tiny-mems-
piezoelectric-absolute-pressure-sensor-enhance-measurement-accuracy)
(/news/tiny-
mems-
piezoelectric-
absolute-
https://circuitdigest.com/electronic-circuits/water-level-indicator-alarm-circuit 19/23
11/28/2018 Simple Water Level Indicator Alarm Circuit Diagram
pressure-
sensor-
enhance-
measurement-
accuracy)
ADC (/forums/embedded/adc)
(/users/baiju) Baiju (/users/baiju) Replies: 1
Inclinomter (/forums/arduino-and-raspberry-pi/inclinomter)
(/users/pete) Pete (/users/pete) Replies: 3
User login
E-mail or username *
Password *
Log in
https://circuitdigest.com/electronic-circuits/water-level-indicator-alarm-circuit 20/23
11/28/2018 Simple Water Level Indicator Alarm Circuit Diagram
pack-
monitoring-
hybrid-
electric-
vehicles%3FHQS=sys-
null-null-
adtrainingseries-
asset-tr-
CircuitDigest-
in&DCM=yes_)
https://circuitdigest.com/electronic-circuits/water-level-indicator-alarm-circuit 21/23
11/28/2018 Simple Water Level Indicator Alarm Circuit Diagram
density?
cu=1134585
&HQS=sys-
null-null-
owmeter-
asset-tr-
CircuitDigest-
in&DCM=yes
&https%3A%2F%2Ftraining.ti.com%2Fgan-
path-high-
power-
density%3Fcu=1134585%20&HQS=sys-
null-null-
owmeter-
asset-tr-
CircuitDigest-
in&DCM=yes_)
more » (https://circuitdigest.com/ti-training/electric-vehicles-videos)
Connect with us on social media and stay updated with latest news, articles and projects!
(https://www.linkedin.com/company/circuit-
(https://www.facebook.com/circuitdigest/)
(https://twitter.com/CircuitDigest)
(https://plus.google.com/+Circuitdigest)
(https://www.youtube.com/channel/UCy3CUAIYgZdAOG9k3IPdL
(https://www.instagram.com/circuit_digest/)
(https://www.pinterest.com/circuitdigest/)
digest/)
CATEGORIES
https://circuitdigest.com/electronic-circuits/water-level-indicator-alarm-circuit 22/23
11/28/2018 Simple Water Level Indicator Alarm Circuit Diagram
POPULAR
NEWSLETTER
Subscribe
Privacy Policy (http://circuitdigest.com/privacy-policy) | Cookie Policy (https://circuitdigest.com/cookie-policy) | Terms of Use (https://circuitdigest.com/terms-of-use) | Contact
Us (http://circuitdigest.com/contact) | Advertise (http://circuitdigest.com/advertise)
https://circuitdigest.com/electronic-circuits/water-level-indicator-alarm-circuit 23/23