Beruflich Dokumente
Kultur Dokumente
All Regions
Version: 00b
Date:2010/09/02
Notice:
For RO to input specific “Legal Requirement” in specific NS regarding to responsibility and
liability statements.
Please check BenQ’s eSupport web site, http://esupport.benq.com, to ensure that you have the
most recent version of this manual.
1
Update History
2
Content Index
Abbreviations & Acronyms....................................................................................................................... 5
About This Manual................................................................................................................................... 6
Trademark ................................................................................................................................................ 6
Introduction ............................................................................................................................................. 6
Important Service Information ................................................................................................................ 6
RoHS (2002/95/EC) Requirements – Applied to all countries require RoHS. ................................. 6
Safety Notice ..................................................................................................................................... 7
Compliance Statement ..................................................................................................................... 7
General Descriptions ........................................................................................................................ 7
Related Service Information ............................................................................................................. 7
Product Overview ..................................................................................................................................... 8
1. Specifications ................................................................................................................................ 9
2. Timing Table ................................................................................................................................. 9
3. Input/output connectors ............................................................................................................ 12
4. Control Key Pad and LED ........................................................................................................... 12
5. Remote Controller ...................................................................................................................... 15
6. Packing ........................................................................................................................................ 16
Customer Acceptance ............................................................................................................................. 34
1. SCOPE ........................................................................................................................................ 34
2. PURPOSE ................................................................................................................................... 34
3. APPLICATION ........................................................................................................................... 34
4. DEFINITION ............................................................................................................................. 35
5. OPERATIONAL INSPECTION CRITERIA ............................................................................... 35
6. Function Test Criteria ................................................................................................................. 35
Level 1 Cosmetic / Appearance / Alignment Service .............................................................................. 40
1. Cosmetic / Appearance Inspection Criteria ................................................................................ 40
2. Software/Firmware Upgrade Process .......................................................................................... 41
2.1 Firmware Upgraded Process ............................................................................................. 41
2.2 Method to enter factory menu.......................................................................................... 46
3. Adjustment / Alignment Procedure ............................................................................................ 47
3.1 Color Wheel Delay Alignment .......................................................................................... 47
3.2 ADC Calibration Procedure ............................................................................................. 50
4. Check Lamp hour information .................................................................................................. 51
5. How to reset lamp hours ............................................................................................................ 51
Level 2 Circuit Board and Standard Parts Replacement ......................................................................... 53
1. Product Exploded View .............................................................................................................. 53
2. Product Disassembly / Assembly ................................................................................................ 54
2.1 Tools.................................................................................................................................. 54
3
2.2 Disassembly Procedure ..................................................................................................... 55
2.3 Replacing the Lamp Module ............................................................................................. 61
2.4 Disassembly the Optical Engine ....................................................................................... 64
3. System Block Diagram ................................................................................................................ 66
4. Troubleshooting .......................................................................................................................... 67
4.1 Confirm Software and hardware ...................................................................................... 67
4.2 Error Count Messages Definition ..................................................................................... 74
Appendix 1 – Screw List / Torque ........................................................................................................... 75
Appendix 2 - Code List: IR / RS232 / DDC Data.................................................................................... 75
1. Remote Control Code................................................................................................................. 77
2. RS232 code table......................................................................................................................... 78
3. DDC Data ................................................................................................................................... 81
Appendix 3 - Ceiling Mount Drawing.................................................................................................... 84
4
Abbreviations & Acronyms
A
A/D Analog to Digital
ADC Analog-Digital Convert
B
BenQ BenQ Corporation
C
CW Color Wheel
D
DLP Digital Light Processing / Texas Instruments®
DMD Digital Micro mirror Device
L
LED Light-Emitting Diode
R
RS232 Interface Between Data terminal Equipment and
Data Communications Equipment Employing
Serial Binary Data Interchange
S
SVGA Super Video Graphics Array, A screen resolution
of 800 x 600 pixels.
SXGA Super XGA. A screen resolution of 1280x1024
pixels.
V
VGA Video Graphics Array. A screen resolution of
640x480 pixels.
X
XGA A screen resolution of 1024x768 pixels.
5
About This Manual
This manual contains information about maintenance and service of BenQ products. Use this manual
to perform diagnostics tests, troubleshoot problems, and align the BenQ product.
Important
Only trained service personnel who are familiar with this BenQ Product shall perform
service or maintenance to it. Before performing any maintenance or service, the
engineer MUST read the “Important Safety Information”
Trademark
The following terms are trademarks of BenQ Corporation:
BenQ
Other companies, products, or service names may be the trademarks of their respective companies.
Introduction
This section contains general service information, please read through carefully. It should be stored for
easy access place.
6
Safety Notice
1 Make sure your working environment is dry and clean, and meets all government safety
requirements.
2 Ensure that other persons are safe while you are servicing the product.
3 DO NOT perform any action that may cause a hazard to the customer or make the product
unsafe.
4 Use proper safety devices to ensure your personal safety.
5 Always use approved tools and test equipment for servicing.
6 Never assume the product’s power is disconnected from the mains power supply. Check that it is
disconnected before opening the product’s cabinet.
7 Modules containing electrical components are sensitive to electrostatic discharge (ESD). Follow
ESD safety procedures while handling these parts.
8 Some products contain more than one battery. Do not disassemble any battery, or expose it to
high temperatures such as throwing into fire or it may explode.
9 Refer to government requirements for battery recycling or disposal.
Compliance Statement
Caution: This Optical Storage Product contains a Laser device. Refer to the product specifications and
your local Laser Safety Compliance Requirements.
General Descriptions
This Service Manual contains general information. There are 2 levels of service:
Level 1: Cosmetic / Appearance / Alignment Service
Level 2: Circuit Board or Standard Parts Replacement
7
Product Overview
8
1. Specifications
All specifications are subject to change without notice.
Optical Control
Resolution RS-232 serial control
(MP615P) 9 pin× 1
800×600 SVGA IR receiver× 1
USB Type B× 1
Input terminals
Display system Computer input
1-CHIP DMD RGB input
D-Sub 15-pin (female) × 2
Lens F/Number
F=2.51 to 2.69 Video signal input
f=21.95 to 24.18 mm S-VIDEO
Mini DIN 4-pin port × 1
Lamp VIDEO
185 W lamp RCA jack × 1
SD/HDTV signal input
Electrical Analog – Component RCA jack × 3
Power supply (through RGB input)
AC100-240V, 2.9A
50-60 Hz (Automatic)
Audio signal input
Power consumption Audio in
260 W (Max);<1 W(Standby) PC audio jack × 1
2. Timing Table
9
Supported timing for PC input
Horizontal
Vertical Pixel
Resolution Frequency Mode
Frequency(Hz) Frequency(MHz)
(kHz)
720×400 31.469 70.087 28.322 720×400_70
31.469 59.940 25.175 VGA_60
37.861 72.809 31.500 VGA_72
640×480
37.500 75.000 31.500 VGA_75
43.269 85.008 36.000 VGA_85
37.879 60.317 40.000 SVGA_60
48.077 72.188 50.000 SVGA_72
800×600
46.875 75.000 49.500 SVGA_75
53.674 85.061 56.250 SVGA_85
48.363 60.004 65.000 XGA_60
56.476 70.069 75.000 XGA_70
1024×768
60.023 75.029 78.750 XGA_75
68.677 84.997 94.500 XGA_85
1024×576 35.82 60.00 46.996 Netbook_1
1024×600 37.5 60.00 45.000 Netbook_2
1024×600 41.467 64.995 51.419 Netbook_3
49.702 59.810 83.500 WXGA_60
1280×800 62.795 74.934 106.500 WXGA_75
71.554 84.880 122.500 WXGA_85
63.981 60.020 108.000 SXGA_60
1280×1024 79.976 75.025 135.000 SXGA_75
91.146 85.024 157.500 SXGA_85
60.000 60.000 108.000 1280×960_60
1280×960
85.938 85.002 148.500 1280×960_85
1440×900 55.935 59.887 106.500 WXGA+_60
1400×1050 65.317 59.978 121.750 SXGA+_60
1600×1200 75.000 60.000 162.000 UXGA
640×480@67Hz 35.000 66.667 30.240 MAC13
832×624@75Hz 49.722 74.546 57.280 MAC16
1024×768@75Hz 60.241 75.020 80.000 MAC19
1152×870@75Hz 68.680 75.060 100.000 MAC21
10
Horizontal Frequency
Signal Format Vertical Frequency(Hz)
(kHz)
480i(525i)@60Hz 15.73 59.94
480p(525p)@60Hz 31.47 59.94
576i(625i)@50Hz 15.63 50.00
576p(625p)@50Hz 31.25 50.00
720p(750p)@60Hz 45.00 60.00
720p(750p)@50Hz 37.50 50.00
1080i(1125i)@60Hz 33.75 60.00
1080i(1125i)@50Hz 28.13 50.00
1080p@60Hz 67.50 60.00
1080p@50Hz 56.25 50.00
11
3. Input/output connectors
(1). USB
This connector is for firmware update and mouse function support.
(2). S-VIDEO
Connect composite video output from video equipment to this jack.
(4). COMPUTER 1
Connect image input signal (analog RGB or component) to this jack.
(5). COMPUTER 2
Connect image input signal (analog RGB or component) to this jack.
(6). AUDIO
Connect an audio output from video equipment to this jack.
(7). VIDEO
Connect composite video output from video equipment to this jack.
(8). RS-232
When operating the projector via a computer, connect this to the controlling computer’s RS-232 port.
12
1. Focus ring
Adjusts the focus of the projected image.
2. Zoom ring
Adjusts the size of the image.
5. ◄Left/BLANK
Used to hide the screen picture.
6. Mode/Enter
Selects an available picture setup mode.
Activates the selected On-Screen Display(OSD)menu item.
7. SOURCE
Displays the source selection bar.
13
Toggles the projector between standby mode and on.
Lights up or flashes when the projector is under operation.
10. ►Right/AUTO
When the On-Screen Display(OSD) menu is activated, the #4,#5,and #10 keys menu are used as
directional arrows to select the desired menu items and to make adjustments.
Automatically determines the best picture timing for the displayed image.
11. Menu/Exit
Turns on the On-Screen Display(OSD) menu. Goes back to previous OSD menu, exits and saves menu
settings.
14
5. Remote Controller
(1) POWER
Toggles the projector between standby mode and on.
(2) ∥/►Freeze
Freeze the projected image.
(3)
Starts the FAQ function.
(4) BLANK
Used to hide the screen picture.
(7) Menu/Exit
Turns on the On-Screen Display(OSD)menu. Goes back to previous OSD menu, exits and saves menu
settings.
15
(8) Keystone/Arrow keys ( /▲ Up , /▼ Down)
Manually corrects distorted images resulting from an angled projection.
(9) AUTO
Automatically determines the best picture timings for the displayed image.
(10) ◄Left/►Right
When the On-Screen Display(OSD) menu is activated, the #8 and #10 keys are used as directional
arrows to select the desired menu items and to make adjustments.
(11) Mode/Enter
Selects an available pictures setup mode.
Activates the selected On-Screen Display(OSD) menu item.
(12) SOURCE
Display the source selection bar.
(14) Timer On
Activates or displays an on-screen timer based on your own timer setting.
6. Packing
16
【NOTE】The updated Service BOM is on SPO system. Please check it to order service parts.
For E SKU
17
For A SKU
For C SKU
18
For J SKU
For K SKU
19
For P SKU
20
For S SKU For T SKU
21
For U SKU
22
CTN LBL PRINTING
1. For E SKU
2. For A SKU
23
3. For C SKU
4. For J SKU
24
5. For K SKU
25
6. For P SKU
26
7. For S SKU
27
8. For T SKU
28
9. For U SKU
29
SPEC LBL PRINTING
1. For E SKU
2. For A SKU
30
3. For C SKU
4. For J SKU
5. For K SKU
31
6. For P SKU
7. For S SKU
8. For T SKU
32
9. For U SKU
33
Customer Acceptance
1. SCOPE
This document establishes the general workmanship standards and functional acceptance criteria for
PROJECTOR produced by BENQ.
2. PURPOSE
The purpose of this publication is to define a procedure for inspection of the PROJECTOR by means
of a customer acceptance test, the method of evaluation of defects and rules for specifying acceptance
levels.
3. APPLICATION
The "Customer Acceptance Criteria" is applicable to the inspection of the PROJECTOR, completely
packed and ready for dispatch to customers. Unless otherwise specified, the customer acceptance
34
inspection should be conducted at manufacturer's site.
4. DEFINITION
The "Customer Acceptance Criteria" is the document defining the process of examining, testing or
otherwise comparing the product with a given set of specified technical, esthetic and workmanship
requirements leading to an evaluation of the "degree of fitness for use", including possible personal
injury or property damage for the use of the product.
36
I/O port Audio input
Test Equipment Connect audio input to audio output of DVD player
Signal format 480i
VGA
I/O port COMPUTER1,COMPUTER2(VGA)
Test Equipment Standard Pattern generator (Ex. Quantum data)
Signal format 800*600 60Hz
Projected image size 60” in diagonal length
Full white
1. Apparent color strip, bend and streak corner on the
2 projected image are not allowable.
2. Can’t see any environmental blemish when projector is
static.
37
DMD Gray 10
The quantity of bright blemish pixel in the active area
should be less than 4 pieces and the diameter of it should be
3 less than 1” (about 2.54 cm).
DMD Blue 60
The quantity of dark blemish pixel in the active area should
4
be less than 4 pieces and the diameter of it should be less
than 1 (about 2.54 cm).
Full darkness
Checking Item: Light leak、DMD Blemish.
1. Light leak in the inactive area should be less than 1.0 lux
5 (<1.0 lux).
2. Any bright pixel in active area is not allowable.
3. Can’t see more than 6 environmental blemish pixels.
P.1
38
Twelve Grids
Checking Item : Abnormal Voice
7
Press “AUTO” button, more than three twinkling grids are
not allowable.
32 Gray Level
Checking Item: Color Gradation
8
32 level of gray level color should be distinguishable and no
defection.
Map
Checking Item: Image Quality
9
The land, ocean (three kinds of colors) and ground should
be distinguishable obviously.
S-Video
I/O port S-Video
Test Equipment Standard Pattern generator (Ex. Quantum data)&DVD player
Signal format NTSC
Criteria No apparent color deviation on the projected image
Video
I/O port Video
39
Signal format NTSC
Test Equipment Standard Pattern generator (Ex. Quantum data)&DVD player
Criteria No apparent color deviation on the projected image
A Surface: Up case- Up case surfaces except right/ left/ behind sides surfaces.
B Surface: Side- Right /left sides surfaces, Back cover surfaces.
C Surface: Low case-bottom surfaces.
Note:
1. Please check the firmware and composer version before any firmware upgrade procedures.
During firmware download period, please do not shut down PC or projector, this will cause flash
memory’s damage. And need to return the unit to manufacturer for flash memory recovery.
2. Computer for operation must be Windows XP or more advanced.
41
Setup Tool / Equipment
Computer
USB Cable(See the picture)
Power Cord
Upgrading Procedure
5. When the installation is finished, click [Finish] and reboot the PC. (A shortcut to DLP Composer
(TM) Lite is created on the desktop.)
42
43
USB Support - Installation (All Platforms)
This release includes support for a USB communications interface to DDP2230/DDP2430 -based
projectors. The setup program includes the files needed to install USB support. After DLP Composer™
Lite is installed, to install the USB support, choose the "Install DLP Device USB Driver" icon under
"DLP Composer™ Lite" in your Start menu.
Follow the instruction on the screen to press any key and wait for the installation done.
And copy the file “FlashDeviceParameters.txt” into the C:\ Program Files\ DLP Composer Lite X.X
Operating procedure
44
6. Move the cursor to [Flash Loader] on the Project window of [DLP Composer Lite]. (The [Flash
Loader] screen will appear.)
7. Click [Browse] and select where the firmware [xxxxxxxxx.img] is for download.
8. Make sure [Skip Boot Loader Area] is with a check.
9. Press Menu and Power buttons constantly and then give power supply (switch power on). Temp
LED and Lamp LED will become amber flashing. That indicates the projector is in the download mode.
At this moment, you can release these two buttons.
10. Click [Reset Bus] firstly to check if USB connects well.
11. Click [Start Download].
45
2.2 Method to enter factory menu
【Warning】
Please don’t set any sub-menu of factory menu that doesn’t refer to in this Service Manual. It may
cause damage to the projector.
46
(5) Press below keys in order will into the Engineering Menu:
Right once Î Left twice Î Right three times Î Left four times.
47
Step2:
Enter the Engineering Mode
Step 3:
1. Move the highlight bar to the CW index delay.
2. Press the button (Right or Left) to adjust the value of CW Index.
3. Notice the changing of color till the RGB colors are distinguishable.
NOTE:
1. The CW Index of each CW is not all the same.
2. Adjusting the CW Index till the R, G, B colors are distinguishable will be fine.
Example:
NG!
The value of CW
Index is too small.
48
DONE!
R, G and B single level
are distinguishable.
49
3.2 ADC Calibration Procedure
Step 1:
Test Image: W100B0
Step2:
Enter the Engineering Mode:
Step 3:
1. Move the highlight bar to the ADC Calibration.
2. Press the Enter button to execute ADC Calibration. Color deviation is unacceptable.
50
4. Check Lamp hour information
(5) A warning message displays asking if you want to reset the lamp timer. Highlight “Reset” and press
Enter. The lamp time will be reset to “0”.
52
Level 2 Circuit Board and Standard Parts Replacement
2.Top Cover
53
2. Product Disassembly / Assembly
2.1 Tools
Item Photo
Screw Bit(+):107
Screw Bit(+):101
Screw Bit(+):102
54
2.2 Disassembly Procedure
【Warning】
♦ Put on the Static Electricity Ring when starting for repair.
♦ Repair Environment suggest in Clean-room class 10000. Do not remove Optical Engine or
DMD panel outside the clean room. Please return the optical engine to supplier if your repair
condition cannot meet the requirement.
♦ While screwing or unscrewing screws, please keep the screwdriver straight. Keeping
screwdriver inclined will damage the screw holes.
♦ Please turn off the power before replacing any parts.
♦ Please wait for the projector lamp cooling down and turn off the power before changing it.
Never touch or hit the lamp module when replacing the lamp.
♦ When you replace the projector lamp, never touch the new lamp with your bare hands. The
invisible residue left by the oil on your hands may shorten the lamp life. Use lint-free gloves
or finger cots are recommended.
55
Step Figure Description
Screw
1
2. Remove the screw on the
bottom cover as shown.
56
Step Figure Description
FFC Cable
Safety switch
1. Disconnect the FFC cable and
safety switch between top cover
and main board.
3
Screws
1. Loosen three screws on the
Key Board to remove it.
4
2. Loosen two screws of safety
switch and then remove it.
Screws
Screws
Screws
57
Step Figure Description
Screws
1. Unscrew all screws on the
metal sheet of Main Board.
Speaker
FAN 2
1. Show you what the connector
should be.
58
Step Figure Description
Note:
2 wires have been connected to
9 To Lamp Ballast. Disconnect these 2 wires
To Power Board
before remove the metal sheet.
Screws
59
Step Figure Description
Screws
1. Loosen all screws as shown.
12
2. Remove the Power Board.
60
2.3 Replacing the Lamp Module
z Hg-Lamp contains mercury. Manage in accordance with local disposal laws. See
www.lamprecycle.org.
z If lamp replacement is performed while the projector is suspended upside-down from the ceiling,
make sure that no one is underneath the lamp socket to avoid any possible injury or damage to the
human eyes caused by fractured lamp.
z To reduce the risk of electrical shock, always turn the projector off and disconnect the power cord
before changing the lamp.
z To reduce the risk of severe burns, allow the projector to cool for at least 45 minutes before
replacing the lamp.
z To reduce the risk of injuries to fingers and damage to internal components, use caution when
removing lamp glass that has shattered into sharp pieces.
z To reduce the risk of injuries to fingers and/or compromising image quality by touching the lens, do
not touch the empty lamp compartment when the lamp is removed.
z This lamp contains mercury. Consult your local hazardous waste regulations to dispose of this lamp
in a proper manner.
z To assure optimal performance from the projector, it is recommended that you purchase a BenQ
projector lamp for lamp replacement.
1. Turn the power off and disconnect the projector from the power outlet. If the lamp is hot, avoid
burns by waiting for approximately 45 minutes until the lamp has cooled.
2. Loosen the screw on the lamp cover.
3. Remove the lamp cover by (a) sliding the cover toward the side
of the projector and (b) lifting it off.
61
4. Loosen the screws that secure the lamp.
5. Lift the handle so that it stands up. Use the handle to slowly
pull the lamp out of the projector.
z Pulling it too quickly may cause the lamp to break and scatter
broken glass in the projector.
z Do not place the lamp in locations where water might splash
on it, children can reach it, or near flammable materials.
z Do not insert your hands into the projector after the lamp is
removed. If you touch the optical components inside, it
could cause color unevenness and distortion of the
projected images.
6. Insert the new lamp into the lamp compartment and make
sure it fits in the projector.
62
10. Tighten the screw that secures the lamp cover.
12. After the startup logo, open the On-Screen Display (OSD)
menu. Go to the SYSTEM SETUP: Advanced > Lamp
Settings menu. Press Mode/Enter. The Lamp Settings
page display. Press ▼ to highlight Reset lamp timer and
press Mode/Enter. A warning message displays asking if
you want to reset the lamp timer. Highlight Reset and press Mode/Enter. The lamp time will be reset
to “0”.
Do not reset if the lamp is not new or replaced as this could cause damage.
63
2.4 Disassembly the Optical Engine
Screws
64
4 Disassembly the Lens
Loosen four screws and then
take off the Lens carefully.
Screws
P.2
Screws
P.3
65
3. System Block Diagram
66
4. Troubleshooting
【Warning】
Do not directly look into the lens to avoid eyesight damages.
The projector is equipped with ventilation holes (intake) and ventilation holes (exhaust). Do not
block or place anything near these slots or internal heat build-up may occur, causing picture
degradation or damage to the projector?
O
Off Off Stand-by mode
G
Off Off Powering up
G
Off Off Normal operation
67
1. The projector needs 90 seconds to
cool down as it was abnormally shut
down without the normal cooling down
process. Or
2. The projector needs to cool for 90
O Off Off
seconds after the power is turned off. Or
3. The projector has shutdown
automatically. If you try to re-start the
projector, it will shutdown again. Please
contact your dealer for assistance.
Lamp events
The projector has shutdown
automatically. If you try to re-start the
Off Off R
projector, it will shutdown again. Please
contact your dealer for assistance.
1. The projector needs 90 seconds to
cool down. Or
Off Off R
2. Please contact your dealer for
assistance.
Thermal events
Off R Off
The projector has shutdown
automatically. If you try to re-start the
Off R Off
projector, it will shutdown again. Please
contact your dealer for assistance.
O Off Off
System events
68
Power Source Troubleshooting:
No Power Source
Fan failure after
after turning on
turning on
NG Replace AC
Check AC socket and Check fan
NG Reconnect fan
socket
connector connection
OK
OK
NG Replace power
Replace fan
Check
Check
NG
Safety Switch board or reinstall
Fan
OK
OK
NG Replace keypad
Check LED and keypad Check
NG Replace
and FPC
FPC Main board Main board
OK
Check 7 pin
NG Check
Power output Fuse
NG
OK OK
board board
69
Fail to light up No Volume
Refer to LED
Check LED
NG indicator and follow Check keypad
NG Replace keypad
OK OK
Check
NG Replace
Check
NG Replace Speaker
OK OK
NG Replace
Check
NG Replace
Check 380V
Power board Main board Main board
output
OK
Check Ballast
NG Replace
Ballast
OK
Check
NG Replace
OK
Check CW NG Replace
70
Video Signal Troubleshooting
Computer Video
No Signal No Signal
Check
NG Turn on
Check
NG Turn on
OK OK
Check
NG Replace
Check
NG Replace
OK OK
Check monitor
NG Replace
Check
NG Replace I/O
OK
Check u5
NG Replace
Check
Main board Replace
Output signal
Main board
Main board
71
Image abnormal Color abnormal
Power on NG Adjust
again and Check input cable
reset OSD and signal setting Input signal
OK OK
OK OK
Check
NG Replace
Check
NG Replace
OK OK
Check NG Replace
Check
NG Replace
Optical Engine Optical Engine Optical Engine Optical Engine
72
Operation Function Troubleshooting
Check
NG Replace
Check
NG Replace
OK OK
Check
NG Replace
Check
NG Replace
OK
Check
NG Replace
IR IR
OK
Check
NG Replace
73
4.2 Error Count Messages Definition
Enter the factory menu to check the error message as shown.
Error Code
// 0x0400: DAD1000 Voltage Error
// 0x0200: DAD1000 Temp Error
// 0x0100: Communication between Main board and Ballast Error
// 0x0080: Lamp No Lit when power on
// 0x0021: CW Error after power on
// 0x0020: CW Error when power on
// 0x0010: FAN3 Error
// 0x0008: FAN2 Error
// 0x0004: FAN1 Error
// 0x0001: T1 Over Temp
Will show Error
74
Appendix 1 – Screw List / Torque
Description Torque Photo
SCREW_TP_4_10_A_2.5_D=6_WH-ZN_NONE_ROHS 7±0.5kgf-cm
SCREW_TP_2.3_8_E_1_D=5_WH-ZN_HEAT-TREATMENT_ROHS 4±0.5kgf-cm
SCREW._TP_2.6_6_A_1.7_D=4.5_WH-ZN_NONE_ROHS 3.5±0.5kgf-cm
SCREW_M_3_6.5_A_1.3_D=6_BLACK_NONE_ROHS 5.5±0.5kgf-cm
SCREW_TP_2_8_A_1.2_D=3.5_BLACK_NONE_ROHS 3±0.5kgf-cm
SCREW_TP_3_8_A_2_D=5.3_BLACK_NONE_ROHS 5.5±0.5kgf-cm
SCREW._M_3_8_A_2_D=5.3_BLACK_NONE_ROHS 5.5±0.5kgf-cm
SCREW-WASHER_TP_2_4_D_1_D=3.2_ZN_NONE_SUS_ROHS 2±0.5kgf-cm
SCREW_M_3_7_A_1.2_D=5.3_BLACK_NONE_ROHS 3±0.5kgf-cm
SCREW-WASHER_M_4_6_A_2.6_D=7_ZN_NONE_SUS_ROHS 6±0.5kgf-cm
SCREW-WASHER_TP_3_5_NONE_2.6_D=5.4_NI_NONE_SUS_ROHS 6±0.5kgf-cm
SCREW-WASHER_TP_3_8_D_2_D=5.5_ZN_NONE_SUS_ROHS 5.5±0.5kgf-cm
HEXAGON-HEAT-BOLT-4.8_PJ-X900_3M_ROHS 4.5±0.5kgf-cm
SCREW+WASHER_M_3_6_D_2_D=5.3_ZN_NONE_SUS_ROHS 5±0.5kgf-cm
75
SCREW_M_3_5_E_1.2_D=6.5_WH-ZN_NL_ROHS 6+/-0.5kgf-cm
SCREW_M_3_5_D_2_D=5.5_NI_NONE_ROHS 6+/-0.5kgf-cm
SCREW._M_2_2.5_A_D=3_A0.8_BLACK_HEAT-TREATMENT_ROHS 2.0±0.2kgf-cm
SCREW_M_3*_7.1_NONE_1.2_D=6_BLACK_NI_ROHS 6.0±0.5kgf-cm
SCREW_M_2_5_A_D=3_A0.8_BLACK_HEAT-TREATMENT_ROHS 1.2+/-0.3kgf cm
76
Appendix 2 - Code List: IR / RS232 / DDC Data
1. Remote Control Code
Key Function Description Code ID and Protocol
1 Power Power on/off toggle 0x02 Frequency 38 KHz
2 Freeze Freeze video 0x03 Protocol NEC Format
3 Menu/Exit OSD Menu On/Off 0x0F Custom Code 0x0030
4 5/ Keystone + 1.Up Key for OSD Menu 0x0B
2.Keystone Correction Increment
5 Auto Auto Adjustment for phase, 0x08
Tracking, Size, Position
6 3 Left Key for OSD Menu 0x0D
7 Mode/Enter 1.Choose a Suitable Preset Mode for 0x10
Usage Environment
2.Enter Key for OSD Menu
8 4 Right Key for OSD Menu. 0x0E
9 Blank Display Blank 0x07
10 6/ Keystone - 1. Down Key for OSD Menu 0x0C
2. Keystone Correction Decrement.
11 Source Input Source Selection 0x04
12 Volume + Speaker Volume Increment 0x82
13 Volume - Speaker Volume Decrement 0x83
14 Digital Zoom + Zoom In 0x18
15 Digital Zoom - Zoom Out 0x19
16 Page Up Page Up Key for Emulation of 0x05
Keyboard
17 Page Down Page Down Key for Emulation of 0x06
Keyboard
18 Timer On Enable/Disable “Presentation 0x25
Timer” Function
19 Timer Set Up Enter “Presentation Timer” Setting 0x26
20 Help? Enter Information menu 0x20
77
2. RS232 code table
2.1 Connection:
Below shows the illustration of connection between PC and Projector.
<CAUTION>
Make sure that your computer and projector are turned off before connection.
Power on the computer first, and then plug the power cord of the projector.
(It may cause Com port incorrect function, if you do not follow this instruction)
Adapters may be necessary depending on the PC connected to this projector. Please contact with
your dealer for further details.
3. DDC Data
Vertical:
Active Time: 600 lines Blanking Time: 28 lines
Sync Offset: 1 lines Sync Pulse Width: 4 lines
Border: 0 lines Frequency: 60.00 Hz
___________________________________________________________________
(108-125) Detailed Timing / Descriptor Block 4:
Monitor Name:
MP615P
83
Appendix 3 - Ceiling Mount Drawing
84