Beruflich Dokumente
Kultur Dokumente
in
BY
Smartworld.asia
Smartzworld.com 1 jntuworldupdates.org
Smartworld.asia Specworld.in
Smartworld.asia
form but these operations can be routinely implemented on a digital computer using
software.
5. Cheaper to implement.
6. Small size.
7. Several filters need several boards in analog, whereas in digital same DSP
processor is used for many filters.
Disadvantages of DSP
1. When analog signal is changing very fast, it is difficult to convert digital form
.(beyond 100KHz range)
2. w=1/2 Sampling rate.
3. Finite word length problems.
4. When the signal is weak, within a few tenths of millivolts, we cannot amplify the
signal after it is digitized.
5. DSP hardware is more expensive than general purpose microprocessors & micro
controllers.
Smartzworld.com 2 jntuworldupdates.org
Smartworld.asia Specworld.in
Smartworld.asia
Classification of Signals
I. Based on Variables:
1. f(t)=5t : single variable
2. f(x,y)=2x+3y : two variables
3. S1= A Sin(wt) : real valued signal
4. S2 = A ejwt : A Cos(wt)+j A Sin(wt) : Complex valued signal
S1(t )
5. S4(t)= S 2(t ) : Multichannel signal
S 3(t )
Smartzworld.com 3 jntuworldupdates.org
Smartworld.asia Specworld.in
Smartworld.asia
IV. Based on the Shape.
1. (n)=0 n 0
=1 n=0
2. u (n) =1 n0
=0 n<0
Smartzworld.com 4 jntuworldupdates.org
Smartworld.asia Specworld.in
n
u(n) = (k ) = (n) + (n-1)+ (n-2)…..
k
= (n k )
k 0
=0 else where.
5.Tri (n/N) = 1- n /N n N
=0 else where.
1. Sinc (n/N)= Sa(n /N) = Sin(n /N) / (n /N), Sinc(0)=1
Sinc (n/N) =0 at n=kN, k= 1, 2…
Smartworld.asia
Sinc (n) = (n) for N=1; (Sin (n ) / n =1= (n))
6.Exponential Sequence
x (n) = A n
If A & are real numbers, then the sequence is real. If 0< <1 and A is +ve, then
sequence values are +ve and decreases with increasing n.
For -1< <0, the sequence values alternate in sign but again decreases in magnitude
with increasing n. If >1, then the sequences grows in magnitude as n increases.
7.Sinusoidal Sequence
x(n) = A Cos(won+ ) for all n
Smartzworld.com 5 jntuworldupdates.org
Smartworld.asia Specworld.in
If = ejwo
A = A ej
x(n) = A ej n ejwon
= A n Cos(won+ ) + j A n Sin(won+ )
If >1, the sequence oscillates with exponentially growing envelope.
If <1, the sequence oscillates with exponentially decreasing envelope.
So when discussing complex exponential signals of the form x(n)= A e jwon or real
sinusoidal signals of the form x(n)= A Cos(won+ ) , we need only consider frequencies
in a frequency internal of length 2 such as < Wo < or 0 Wo<2 .
V. Deterministic (x (t) = t x (t) = A Sin(wt))
& Non-deterministic Signals. (Ex: Thermal noise.)
VI. Periodic & non periodic based on repetition.
VII. Power & Energy Signals
Smartworld.asia
Energy signal: E = finite, P=0
Signal with finite energy is called energy signal.
Energy signal have zero signal power, since averaging finite energy over infinite
time. All time limited signals of finite amplitude are energy signals.
Ex: one sided or two sided decaying. Damped exponentials, damped sinusoidal.
1
x(t) is an energy signal if it is finite valued and x 2 (t) decays to zero fasten than
t
as t .
Power signal: E = , P 0, P Ex: All periodic waveforms
Neither energy nor power: E= , P=0 Ex: 1/ t t 1 E= , P= , Ex: tn
VIII. Based on Symmetry
1. Even x(n)=xe(n)+xo(n)
2. Odd x(-n)=xe(-n)+xo(-n)
3. Hidden x(-n)=xe(n)-xo(n)
1
4. Half-wave symmetry. xe(n)= [x(n)+x(-n)]
2
Smartzworld.com 6 jntuworldupdates.org
Smartworld.asia Specworld.in
1
xo(n)= [x(n)-x(-n)]
2
Signal Classification by duration & Area.
a. Finite duration: time limited.
b. Semi-infinite extent: right sided, if they are zero for t < where = finite
Smartworld.asia
Piecewise continuous: possess different expressions over different intervals.
Continuous: defined by single expressions for all time. x(t) = sin(t)
Periodic: xp (t) = xp (t nT)
T
1
T 0
2
For periodic signals P = x(t ) dt
X rms = P
Smartzworld.com 7 jntuworldupdates.org
Smartworld.asia Specworld.in
1 2 1 2
E= A2 b E= A b E= A b
2 3
Q.
e - t dt =
1
0
Smartworld.asia
Q.
1 2 1
Ex = A 0.5T + (-A)2 0.5T = 0.5 A2 T
2 2
Smartzworld.com 8 jntuworldupdates.org
Smartworld.asia Specworld.in
Px = 0.5 A2
Q.
1 1 2
Ey = [ A2 0.5T] 2 = A T
3 3
1 2
Py = A
3
Smartworld.asia
x(1-t): fold x(t) & shift right by 1 OR shift right and fold.
x(0.5t +0.5) Advance by 0.5 & stretched by 2 OR stretched by 2 & advance by 1.
(t 2) t 2
y (t) = 2 x [- ] = 2 x[ ] 2 x( t + ) ; 5 + =-1; - + =1 => = -1/3
3 3 3
; = 2/3
Area of symmetric signals over symmetric limits (- , )
Odd symmetry:
x0 (t) dt =0
Even symmetry:
xe (t) dt = 2
0
xe (t) dt
Smartzworld.com 9 jntuworldupdates.org
Smartworld.asia Specworld.in
Area of any sinc or Sinc 2 equals area of triangle ABC inscribed within the main lobe.
10
Smartzworld.com 10 jntuworldupdates.org
Smartworld.asia Specworld.in
Even though the sinc function is square integrable ( an energy signal) , it is not
1
absolutely integrable( because it does not decay to zero faster than )
t
(t) = 0 t 0
= t=0 ( )d
=1
An impulse is a tall narrow spike with finite area and infinite energy.
The area of impulse A (t) equals A and is called its strength. How ever its hight at
t=0 is .
Smartworld.asia
= 2 (t) – 2e-t u(t)
2 e-t (t) = 2 (t)
1
[ [t- ]] = (t )
2 2
I 2 = cos(2 t ) (2t 1)dt = cos(2 t )0.5 (t 0.5)dt = 0.5 cos(2 t) at t=-0.5 = -0.5
4 4
x1(t) = x(t)
k
(t-kts ) =
k
x(kts) (t-kts)
11
Smartzworld.com 11 jntuworldupdates.org
Smartworld.asia Specworld.in
’(t) =0 t 0
1
[ [t- ]] = (t )
Differentiating on both sides
1
’ [ [t- ]] = ' (t )
With =-1
’ (-t) = - ’ (t)
d
[ x(t ) (t )] = x’ (t) (t- ) + x (t) ’ (t- )
dt
= x’ ( ) (t- ) + x (t) ’ (t- )-----------1
Or
d d
[ x(t ) (t )] = [ x( ) (t )] = x ( ) ’ (t- ) -----------2
dt dt
1=2
x’ ( ) (t- ) + x (t) ’ (t- ) = x ( ) ’ (t- )
12
Smartzworld.com 12 jntuworldupdates.org
Smartworld.asia Specworld.in
x (t) ’ (t- ) dt =
x ( ) ’ (t- ) dt -
x’ ( ) (t- ) dt
= 0- x’ ( ) = - x’ ( )
Higher derivatives of (t) obey n(t) = (-1)n n(t) are alternately odd and even,
and possess zero area. All are eliminating forms of the same sequence that generate
impulses, provided their ordinary derivatives exits. None are absolutely integrable.
The impulse is unique in being the only absolutely integrable function from among
all its derivatives and integrals (step, ramp etc)
What does the signal x(t) = e-t ’(t) describe?
x(t) = ’ (t) – (-1) (t) = ’ (t) + (t)
2
d
= 0.5 (t-3) t 1 - 8 [cos t ] t 0.5
dt
= 23.1327 Answer.
Operation on Signals:
Smartworld.asia
1. Shifting.
x(n) shift right or delay = x(n-m)
x(n) shift left or advance = x(n+m)
2. Time reversal or fold.
x(-n+2) is x(-n) delayed by two samples.
x(-n-2) is x(-n) advanced by two samples.
Or
x(n) is right shift x(n-2), then fold x(-n-2)
x(n) fold x(-n) shift left x(-(n+2)) = x(-n-2)
Ex:
x(n) = 2, 3 , 4 , 5, 6, 7 .
13
Smartzworld.com 13 jntuworldupdates.org
Smartworld.asia Specworld.in
Smartworld.asia
y(n) = x(n/2) corresponds to x(t) sampled at Ts/2 and has twice the length of x(n)
with one new sample between adjacent samples of x(n).
The new sample value as ‘0’ for Zero interpolation.
The new sample constant = previous value for step interpolation.
The new sample average of adjacent samples for linear interpolation.
Interpolation by a factor of N is equivalent to sampling x(t) at intervals Ts/N and
implies an N-fold increase in both the sampling rate and the signal length.
Ex: Decimation Step interpolation
{ 1 , 2, 6, 4, 8} { 1 , 6, 8} { 1 , 1, 6, 6, 8, 8}
n 2n n n/2
{ 1 , 2, 6, 4, 8} { 1 , 1,2,2,6, 6,4,4,8, 8} { 1 , 2, 6, 4, 8}
n n/2 n 2n
Since Decimation is indeed the inverse of interpolation, but the converse is not
necessarily true. First Interpolation & Decimation.
Ex: x(n) = { 1 1, 2, 5, -1}
14
Smartzworld.com 14 jntuworldupdates.org
Smartworld.asia Specworld.in
4 5 2 1
= { 1, , , 2 , 3,4,5,3,1,-1, - ,- } Linear interpolation.
3 3 3 3
4. Fractional Delays.
M ( Nn M )
It requires interpolation (N), shift (M) and Decimation (n): x (n - )=x( )
N N
2n 1
x(n) = {2, 4, 6 , 8}, find y(n)=x(n-0.5) = x ( )
2
g(n) = x (n/2) = {2, 2, 4, 4, 6 , 6, 8,8} for step interpolation.
n 1
h(n) =g(n-1) = x( ) = {2, 2, 4, 4 , 6, 6,8,8}
2
2n 1
y(n) = h(2n) = x(n-0.5) = x( ) = {2, 4 , 6, 8}
2
OR
Smartworld.asia
g(n) = x(n/2) = {2,3,4,5, 6 ,7,8,4} linear interpolation.
g (n) = h(2n)={3,5,7,4}
Classification of Systems
1. a. Static systems or memory less system. (Non Linear / Stable)
Ex. y(n) = a x (n)
= n x(n) + b x3(n)
= [x(n)]2 = a(n-1) x(n)
y(n) = [x(n), n]
If its o/p at every value of ‘n’ depends only on the input x(n) at the same value of ‘n’
Do not include delay elements. Similarly to combinational circuits.
b. Dynamic systems or memory.
If its o/p at every value of ‘n’ depends on the o/p till (n-1) and i/p at the same value of
‘n’ or previous value of ‘n’.
15
Smartzworld.com 15 jntuworldupdates.org
Smartworld.asia Specworld.in
This system computes the nth sample of the o/p sequence as the average of (m1+m2+1)
samples of input sequence around the nth sample.
Smartworld.asia
If M1=0; M2=5
5
y(7) = 1/6 [ x (7 k ) ]
k 0
n 1
= x(k ) + x(n)
k
= y(n-1) + x(n)
16
Smartzworld.com 16 jntuworldupdates.org
Smartworld.asia Specworld.in
x(n) = { …0,3,2,1,0,1,2,3,0,….}
y(n) = { …0,3,5,6,6,7,9,12,12…}
O/p at the nth sample depends on the i/p’s till nth sample
Ex:
x(n) = n u(n) ; given y(-1)=0. i.e. initially relaxed.
1 n
y(n) = x(k ) + x(k )
k k 0
n n
n(n 1)
= y(-1) + x(k ) = 0 +
k 0
n =
k 0 2
5. Linear Systems.
If y1(n) & y2(n) are the responses of a system when x1(n) & x2(n) are the respective
inputs, then the system is linear if and only if
[ x1(n) x2(n)] = [ x1(n)] + [ x2(n)]
Smartworld.asia
The two properties can be combined into principle of superposition stated as
[ax1(n) bx2(n)] = a [ x1(n)] + b [ x2(n)]
17
Smartzworld.com 17 jntuworldupdates.org
Smartworld.asia Specworld.in
For every bounded input x(n) Bx < for all n, there exists a fixed +ve finite value
y(n) = [ x(k ) (n k ) ] for linear
k
Therefore o/p of any LTI system is convolution of i/p and impulse response.
y(no) = h(k ) x(no k )
k
1
= h(k ) x(no k ) + h(k ) x(no k )
Smartworld.asia
k k 0
n
If i/p is also causal y(n) = h( k ) x ( n k )
k 0
18
Smartzworld.com 18 jntuworldupdates.org
Smartworld.asia Specworld.in
Smartworld.asia
h (n) = h1(n) + h2(n)
7 LTI systems are stable if and only if impulse response is absolutely summable.
y (n) = h( k ) x ( n k )
k
k
h(k ) x(n k )
S=
k
h(k ) is necessary & sufficient condition for stability.
19
Smartzworld.com 19 jntuworldupdates.org
Smartworld.asia Specworld.in
= h( k ) x ( n k )
k
y (n+N) = h( k ) x ( n k N )
k
put n-k = m
= h(n m) x(m N )
m
= h(n m) x(m)
m
m=k
= h( n k ) x ( k )
k
= y(n) (Ans)
Smartworld.asia
h(1) = 0.4 h(0) = 0.4
h(2) = 0.42
h(n) = 0.4n for n 0
Q. y(n)-0.4 y(n-1) = x(n). find the anti-causal impulse response? h(n)=0 for n 0
h(n-1) = 2.5 [h(n)- (n) ]
h(-1) = 2.5 [h(0)- (0) ] = -2.5
h(-2) = -2.52 . …….. h(n) = -2.5n valid for n -1
Q. x(n)={1,2,3} y(n)={3,4} Obtain difference equation from i/p & o/p information
y(n) + 2 y(n-1) + 3 y(n-2) = 3 x(n) + 4 x(n-1) (Ans)
Q. x(n) = {4,4,}, y(n)= x(n)- 0.5x(n-1). Find the difference equation of the inverse
system. Sketch the realization of each system and find the output of each system.
Solution:
The original system is y(n)=x(n)-0.5 x(n-1)
The inverse system is x(n)= y(n)-0.5 y(n-1)
y (n) = x (n) – 0.5 x(n-1)
Y (z) = X (z) [1-0.5Z-1]
20
Smartzworld.com 20 jntuworldupdates.org
Smartworld.asia Specworld.in
Y ( z)
=1-0.5 Z-1 System
X ( z)
Inverse System
y (n) – 0.5 y(n-1) =x(n)
Y (z) [1-0.5 Z-1] = X (z)
Y ( z)
X ( z)
-1 -1
[1-0.5 Z ] Smartworld.asia
g (n) = 4 (n) - 2 (n-1) + 4 (n-1) - 2 (n-2) = 4 (n) + 2 (n-1) - 2 (n-2)
y (n) = 0.5 y(n-1) + 4 (n) + 2 (n-1) – 2 (n-2)
y (0) = 0.5y(-1) + 4 (0) = 4
y(1) = 4
y(2) = 0.5 y(1) - 2 (0) = 0
y(n) = {4, 4} same as i/p.
Non Recursive filters Recursive filters
N N
y(n) =
k
ak x(n-k) y(n) =
k 0
ak x(n-k) –
k 1
bk y(n-k)
21
Smartzworld.com 21 jntuworldupdates.org
Smartworld.asia Specworld.in
N
always.
y(n) = ak x(n-k)
k 0
y(n) – y(n-1) = x(n) – x(n-3)
Present response depends only on present
i/p & previous i/ps but not future i/ps. It gives
FIR o/p.
1
Q. y(n) = [x (n+1) + x (n) + x (n-1)] Find the given system is stable or not?
3
Let x(n) = (n)
1
h(n) = [ (n+1) + (n) + (n-1)]
3
1
h(0) =
3
1
h(-1) =
3
1
h(1) =
3
S= h(n) <
Smartworld.asia
therefore Stable.
22
Smartzworld.com 22 jntuworldupdates.org
Smartworld.asia Specworld.in
1
y(-1) = [ y(0) – x(0)]=0
a
y(-2) = 0
1
Q. y(n) = y(n-1) + x(n) for n 0
n 1
=0 otherwise. Find whether given system is time variant or not?
Let x(n) = (n)
h (0) = 1 y(-1) + (0) = 1
h(1) = ½ y(0) + (1) = ½
h(2) = 1/6
h(3) = 1/24
if x(n) = (n-1)
y(n) = h(n-1)
1
h(n-1) = y(n) = h(n-2) + (n-1)
n 1
Smartworld.asia
n=0 h(-1) = y(0) = 1 x 0+0 =0
n=1 h(0) = y(1) = ½ x 0 + (0)= 1
n=2 h(1) = y(2) = 1/3 x 1 + 0 = 1/3
h(2) = 1/12
h (n, 0) h(n,1) TV
Q. y (n) = 2n x(n) Time varying
1
Q. y (n) = [x (n+1) + x (n) + x (n-1)] Linear
3
Q. y (n) = 12 x (n-1) + 11 x(n-2) TIV
Q. y (n) = 7 x2(n-1) non linear
Q. y (n) = x2(n) non linear
Q. y (n) = n2 x (n+2) linear
Q. y (n) = x (n2) linear
Q. y (n) = ex(n) non linear
Q. y (n) = 2x(n) x (n) non linear, TIV
23
Smartzworld.com 23 jntuworldupdates.org
Smartworld.asia Specworld.in
(If the roots of characteristics equation are a magnitude less than unity. It is a
necessary & sufficient condition)
Non recursive system, or FIR filter are always stable.
Q. y (n) + 2 y2(n) = 2 x(n) – x(n-1) non linear, TIV
Q. y (n) - 2 y (n-1) = 2x(n) x (n) non linear, TIV
Q. y (n) + 4 y (n) y (2n) = x (n) non linear, TIV
Q. y (n+1) – y (n) = x (n+1) is causal
Q. y (n) - 2 y (n-2) = x (n) causal
Q. y (n) - 2 y (n-2) = x (n+1) non causal
Q. y (n+1) – y (n) = x (n+2) non causal
Q. y (n-2) = 3 x (n-2) is static or Instantaneous.
Q. y (n) = 3 x (n-2) dynamic
Q. y (n+4) + y (n+3) = x (n+2) causal & dynamic
Q. y (n) = 2 x ( n )
Smartworld.asia
If =1 causal, static
<1 causal, dynamic
>1 non causal, dynamic
1 TV
Q. y (n) = 2(n+1) x (n) is causal & static but TV.
Q. y (n) = x (-n) TV
Solution of linear constant-co-efficient difference equation
Q. y(n)-3 y (n-1) – 4 y(n-2) = 0 determine zero-input response of the system;
Given y(-2) =0 & y(-1) =5
Let solution to the homogeneous equation be
yh (n) = n
- 3 - 4 n-2 =0
n n-1
[ 2 - 3 - 4] =0
n-2
= -1, 4
yh (n) = C1 1n + C2 2n = C1(-1)n + C2 4n
y(0) = 3y(-1) +4 y(-2) = 15
24
Smartzworld.com 24 jntuworldupdates.org
Smartworld.asia Specworld.in
C1+ C2 =15
y (1) = 3y (0) +4 y (-1) = 65
-C1+4C2 = 65 Solve: C1 = -1 & C2=16
y(n) = (-1)n+1 + 4n+2 (Ans)
If it contain multiple roots yh(n) = C1 1n + C2 n 1n + C3 n2 1n
or 1n [C1+ nC2 + n2 C3….]
Q. Determine the particular solution of y(n) + a1y(n-1) =x(n)
x(n) = u(n)
Let yp (n) = k u(n)
k u(n) + a1 k u(n-1) =u(n)
To determine the value of k, we must evaluate this equation for any n 1
k + a1 k =1
1
k=
1 a1
1
Smartworld.asia
yp (n) = u(n) Ans
1 a1
x(n) yp(n)
1. A K
2. Amn Kmn
3. Anm Ko nm + K1nm-1 + …. Km
4. A Coswon or A Sinwon K1 Coswon + K2 Sinwon
5 1
Q. y(n) = y(n-1) - y(n-2) + x(n) x(n) = 2n n 0
6 6
Let yp (n) = K2n
5 1
K2n u(n) = K 2n-1 u(n-1) - K 2n-2 u(n-2) + 2n u(n)
6 6
For n 2
5 1
4K = (2K) - K +4 Solve for K=8/5
6 6
8 n
yp (n) = 2 Ans
5
Q. y(n) – 3 y(n-1) - 4 y(n-2) = x(n) + 2x(n-1) Find the h(n) for recursive system.
25
Smartzworld.com 25 jntuworldupdates.org
Smartworld.asia Specworld.in
Smartworld.asia
plot for h(n) in both the methods are same.
Q. y(n) – 0.5 y(n-1) = 5 cos 0.5n n 0 with y(-1) = 4
yh(n) = n
– 0.5
n n-1
=0
[ -0.5] =0
n-1
=0.5
yh(n) = C (0.5)n
yp(n) = K1 cos 0.5n + K2 sin 0.5n
yp(n-1) = K1 cos 0.5(n-1) + K2 sin 0.5(n-1)
= - K1 sin 0.5n - K2cos 0.5n
yp(n) - 0.5 yp(n-1) = 5 cos 0.5 n
= (K1 + 0.5 K2) cos 0.5 n -(0.5 K1 – K2) sin 0.5n
K1 + 0.5 K2 = 5
0.5 K1 – K2 =0 Solving we get: K1= 4 & K2=2
yp(n) = 4 cos 0.5 n + 2 sin 0.5n
26
Smartzworld.com 26 jntuworldupdates.org
Smartworld.asia Specworld.in
= rad / sec
Smartworld.asia
w = rad / Sample
F = cycles / sec f = cycles / Sample
2) A Discrete- time – sinusoid is periodic only of its f is a Rational number.
x (n+N) = x (n)
Cos 2 f0 (n+N) = Cos 2 f0 n
K
2 f0N = 2 K => f0 =
N
Ex: A Cos ( )n
6
w= =2 f
6
1
f= N=12 Samples/Cycle ; Fs= Sampling Frequency; Ts =
12
Sampling Period
Q. Cos (0.5n) is not periodic
27
Smartzworld.com 27 jntuworldupdates.org
Smartworld.asia Specworld.in
[Complex exponential and sinusoidal sequences are not necessarily periodic in ‘n’
2
Smartworld.asia
with period ( ) and depending on Wo, may not be periodic at all]
Wo
N = fundamental period of a periodic sinusoidal.
3. The highest rate of oscillations in a discrete time sinusoid is obtained when
w = or -
28
Smartzworld.com 28 jntuworldupdates.org
Smartworld.asia Specworld.in
=> f =
Smartworld.asia
3
16
1
6. If analog signal frequency = F = samples/Sec = Hz then digital frequency f = 1
Ts
W= Ts
2 f = 2 F Ts => f =1
;
2 F = 4 2 f = /4
29
Smartzworld.com 29 jntuworldupdates.org
Smartworld.asia Specworld.in
1 1
F= ; T= 8 ; f= N=8
8 8
7. Discrete-time sinusoids are always periodic in frequency.
Smartworld.asia
Q. The signal x (t) = 2 Cos (40 t) + Sin (60 t) is sampled at 75Hz. What is the
common period of the sampled signal x (n), and how many full periods of x (t) does it
take to obtain one period of x(n)?
F1 = 20Hz F2 = 30Hz
20 4 K1 30 2 K 2
f1 = f2 =
75 15 N1 75 5 N 2
The common period is thus N=LCM (N1, N2) = LCM (15, 5) = 15
The fundamental frequency Fo of x (t) is GCD (20, 30) = 10Hz
1
And fundamental period T = 0.1s
Fo
Since N=15
1
1sample ---------- sec
75
15
15 sample ----------- ? => 0.2S
75
30
Smartzworld.com 30 jntuworldupdates.org
Smartworld.asia Specworld.in
So it takes two full periods of x (t) to obtain one period of x (n) or GCD (K 1, K2) =
GCD (4, 2) = 2
Frequency Domain Representation of discrete-time signals and systems
For LTI systems we know that a representation of the input sequence as a weighted
sum of delayed impulses leads to a representation of the output as a weighted sum of
delayed responses.
Let x (n) = ejwn
y (n) = h (n) * x (n)
=e jwn
h(k ) e-jwk
k
jw
Let H (e ) = h(k ) e-jwk is the frequency domain representation of the system.
k
Smartworld.asia
y (n) = H (e ) e
jw jwn
ejwn = eigen function of the system.
H (ejw) = eigen value
Q. Find the frequency response of 1st order system y (n) = x (n) + a y (n-1)
(a<1)
Let x (n) = ejwn
yp (n) = C ejwn
C ejwn = ejwn + a C ejw (n-1)
C ejwn [1-ae-jw] = ejwn
1
C=
[1 ae jw ]
1 1
Therefore H (ejw) = =
[1 ae jw ] 1 a(cos w j sin w)
1
H (e jw ) =
1 2a cos w a 2
aSinw
H (e jw ) Tan 1 ( )
1 aCosw
31
Smartzworld.com 31 jntuworldupdates.org
Smartworld.asia Specworld.in
1
Q. Frequency response of 2nd order system y(n) = x(n) - y (n 2)
2
x (n) = e jwn
y (n) ce jwn
Smartworld.asia
p
1 jw( n 2)
c e jwn = e jwn - ce
2
1 1 20 16Cos2 w
c e jwn (1+ e 2 jw ) = e jwn c= c
2 1
1 e 2 jw 5 4Cos2 w
2
Sin 2 w
c tan1
2 Cos2 w
32
Smartzworld.com 32 jntuworldupdates.org
Smartworld.asia Specworld.in
UNIT - II
c e
jK n
N
DTFS
Non periodic Periodic Ck =
T
1 N 1 2
Ck = T
0
f (t )e jKot dt 1
x p ( n )e
j
N
nK
N n 0
2nTs
1 jK
k=0 to N-1
T
x ( n)e
Smartworld.asia
NTs
T = N Ts
t = n Ts : dt = Ts
Non-Periodic f(t) = Non – Periodic x(n) =
2
1 1
F (w)e X (w)e
jt
d jwn
dw
2
2 0
X(w) = FT of DTS
f (t )e jt dt
33
Smartzworld.com 33 jntuworldupdates.org
Smartworld.asia Specworld.in
1
=
x ( n ) x ( n ) x *
( n ) x ( n ) X *
( w) e jwn
dw
E=
n n n 2 0
2
1 jwn
=
2 0 X ( w)
*
n
x ( n ) e dw
2
1
X
*
= 2 ( w) X ( w)dw
0
2
1
=
2 X ( w)
dw
2 2
1
Therefore: E= x ( n )
2 X (w) dw -------- Parsval’s Theorem
n
P = Lt
1 Smartworld.asia
N 2 N 1
N
x ( n)
2
N 1 2
1
= N
n 0
x ( n) for periodic Signal
2
1 N 1 1 N 1 N 1
* j N nk
=
N n 0
x ( n) x ( n) x ( n) C k e
*
N n 0 k 0
2
* 1
N 1 N 1 j
x ( n)e
nk
Ck N
=
k 0 N n 0
N 1 2 N 1 2
Therefore P= C
k 0
k E=N Ck
k 0
34
Smartzworld.com 34 jntuworldupdates.org
Smartworld.asia Specworld.in
N
1
P = Lt
N 2 N 1 n 0
u 2 ( n)
N 1 1
= Lt Power Signal
N 2 N 1 2
E=
jwon
Ex: x (n) = Ae
N 2
1
P= Lt
N 2 N 1 n N
Ae jwon
1
= Lt A 2 [1 1 ........]
N 2 N 1
A 2 (2 N 1)
Lt 2 N 1 A 2
Smartworld.asia
= it is Power Signal and E=
N
2n
Ex: x (n) = 6 Cos whose period is N=4 x (n) = { 6 ,0,6,0 }
4
1 3 2 1
P=
4 n 0
x ( n )
4
[36 36] 18W
2n
j
4
Ex: x (n) = 6 e whose period is N = 4
2
1 3 1
P=
4 n 0
x ( n )
4
[36 36 36 36] 36Watts
35
Smartzworld.com 35 jntuworldupdates.org
Smartworld.asia Specworld.in
DISCRETE CONVOLUTION
Smartworld.asia
It is a method of finding zero input response of linear Time Invariant system.
u(k) = 0 k<0
u(n-k) = 0 k>n
n
u(k )u(n k )
n
k 0
= 1 = (n+1) u(n) = r(n+1)
k 0
36
Smartzworld.com 36 jntuworldupdates.org
Smartworld.asia Specworld.in
y(n) = k 0
ak an-k = an (n+1) u(n)
y(n) =
k
k
u(k) u(n-k) =
k 0
k
= (1-
n+1
) / (1- )
The convolution of the left sided signals is also left sided and the convolution of two
right sided also right sided.
n n
Q. x(n) = rect ( )=1 N
2N
=0 else where
h(n) = rect ( n )
2N
Smartworld.asia
= u (n+N) * u (n+N) – 2 u (n+N)*u (n-N-1)] + u (n-N-1) * u (n-N-1)
= r(n+2N+1) – 2r(n) + r(n-2N-1)
n
= (2N+1) Tri ( )
2N 1
n
Tri ( n ) = 1- for n N
N N
=0 elsewhere.
37
Smartzworld.com 37 jntuworldupdates.org
Smartworld.asia Specworld.in
Q. x(n) = {2,-1,3}
h(n) = { 1,2,2,3} Graphically Fold-shift-multiply-sum
y(n) =
Smartworld.asia
1 2 2 3
2 2 4 4 6
-1 -1 -2 -2 -3
3 3 6 6 9
y(n) = { 2,3,5,10,3,9}
Q. x(n) = {4, 1
,3} h(n) = { 2,5, 0
,4}
2 5 0 4
4 8 20 0 16
1 2 5 0 4
3 6 15 0 12
y(n) = { 8,22,11,31,4, 12 } Note that convolution starts at n=-3
38
Smartzworld.com 38 jntuworldupdates.org
Smartworld.asia Specworld.in
Q)
h(n): 2 5 0 4
x(n): 4 1 3
_________________________________
8 20 0 16
2 5 0 4
6 15 0 12
____________________________________
y(n): 8 22 11 31 4 12
i) 2 5 0 4 ii) 2 5 0 4
3 1 4 3 1 4
Smartworld.asia
___________________ _________________________
y(0) = 8 2 20 y(1) = 2+20 = 22
iii) 2 5 0 4 iv) 2 5 0 4
3 1 4 3 1 4
________________________ _______________________
6 5 0 y(2) = 11 15 0 16 y(3) = 31
v) 2 5 0 4 Vi) 2 5 0 4
3 1 4 3 1 4
________________________ _______________________
0 4 y(4) = 4 12 y(5) = 12
If we insert zeros between adjacent samples of each signal to be convolved, their
convolution corresponding to the original convolution sequence with zeros inserted
between its adjacent samples.
39
Smartzworld.com 39 jntuworldupdates.org
Smartworld.asia Specworld.in
y(n) = 8 ,22,11,31,4,12
h(n) = 2 , 0, 5, 0, 0, 0, 4 ; x(n) = 4, 0, 1, 0, 3
Smartworld.asia
____________________________________________________________
y1(n) = (h (n)*x1(n))1 1 1 3 2
y2(n) = 1 4 4 0 -1
y3(n) = 1 5 8 5 1
y(n) = { 1 1 1 4 6 4 1 4 8 5 1}
40
Smartzworld.com 40 jntuworldupdates.org
Smartworld.asia Specworld.in
b. x (n) = Cos n after expansion x(n)={ 1,0.5,-0.5,-1,-0.5,0.5}
3
1
fo = N=6
6
2
1 5 j
Ck =
nk
6
x ( n )e k=0 to 5
6 n 0
Ck =
1 Smartworld.asia
j k
x(0) x(1)e x(2)e
6
3
j k
3
2
jk
x(3)e x(4)e
j k
3
j k
x(5)e 3
4 5
For k=0 Co =
1
x(0) x(1) x(2) x(3) x(4) x(5) = 0
6
Similarly
K=1 C1 = 0.5 , C2 = 0 = C3 = C4 , C5 = 0.5
Or
2 2 2
1 j 6 n 1 j 5
C
n j kn
= Cos n e
6
x (n) + e = k e 6
3 2 2 k 0
41
Smartzworld.com 41 jntuworldupdates.org
Smartworld.asia Specworld.in
2 4 6 8 10
j n j n j n j n j n
6 6 6 6 6
= Co+C1 e +C2e + C3 e +C4 e +C5 e
1
By comparison C1=
2
2 56 10n
j n j 2 n j
6 6 6
Since e =e =e
1
C5
2
c. x (n) = {1,1,0,0}
nk
1 3 j 2
Ck= 4
4
x ( n ) e k=0, 1, 2, 3
n 0
2k
1 j
1 1e
2
= 4
cSmartworld.asia
1
c0 2 ;
1
c 0 c
1
4
1 j ; 2 ; 3
1
4
1 j
1
Co & C0 = 0
2
2
c 1
& C1 =
4 4
c 2
0 & C2 undefined
2
c 3
& C3 =
4 4
42
Smartzworld.com 42 jntuworldupdates.org
Smartworld.asia Specworld.in
PROPERTIES OF DFS
1. Linearity
DFS x ( n m) e
j
~ N
Ck
3. Symmetry
x (Smartworld.asia
N 1 2n k
1 j
N
~
n 0
n )e N
N 1
~
x (n) C
* *
k
~
x (n) C k e
j2
N
nk
DFS
k 0
~ ~ ( n) 1
*
DFS
Re~
x ( n ) DFS
x ( n ) x
C k C *
k C ke
2 2
~ ~ ( n) 1
*
j Imx (n) DFS
~ x ( n ) x
C k C * k C ko
DFS
2 2
~
x ( n)
If is real then
~
x ( n ) ~
x *
( n)
~
x e ( n)
2
43
Smartzworld.com 43 jntuworldupdates.org
Smartworld.asia Specworld.in
~ ~x ( n) ~
x * ( n)
x o ( n)
2
DFS
~
x e ( n )
1
2
C k C *
k ReC k
DFS
~
x o ( n )
1
C k
2
C *
k j ImC k
Periodic Convolution
N 1 ~
1
~
x ( m) x 2 ( n m) C k1C k 2
DFS
m 0
If x(n) is real
Ck C * k
Smartworld.asia
Re[Ck ] Re[Ck ]
Im[Ck ] Im[Ck ]
Ck Ck
Ck Ck
PROPERTIES OF FT (DTFT)
1. Linearity
y (n) = a x1 (n) + b x2 (n)
Y (e jw ) = a X1(e jw ) + b X2(e jw )
2. Periodicity
j ( w 2 )
H (e ) = H (e jw )
3. For Complex Sequence
44
Smartzworld.com 44 jntuworldupdates.org
Smartworld.asia Specworld.in
H (e ) = jw
[ h
n -
R (n) j h I (n) ] [Cos(wn) - j Sin(wn)]
[ h
n -
R (n) Cos(wn) h I (n)Sin(wn) = HR (e jw
)
[ h (n) Cos(wn) h
n -
I R (n)Sin(wn) = HI (e jw
)
H (e jw ) = H R (e jw ) jH I (e jw )
= H R2 (e jw ) H I2 (e jw ) H (e jw ) H * (e jw )
H I (e jw ) 1
H (e ) tan jw
jw
R
H ( e )
4. For Real Valued Sequence
H (e Smartworld.asia
) h(n)e jw jwn
=
n
= h(n)Cos(wn) j h(n)Sin(wn)
n n
= H R (e jw ) jH I (e jw ) -------------------- (a)
H (e jw
) = h(n)e
n
jwn
= h(n)Cos(wn) j h(n)Sin(wn)
n n
= H R (e jw ) jH I (e jw ) -------------------- (b)
From (a) & (b)
H R (e jw ) H R (e jw )
45
Smartzworld.com 45 jntuworldupdates.org
Smartworld.asia Specworld.in
H I (e jw ) H I (e jw )
Real part is even function of w
Imaginary part is odd function of w
H (e jw ) H * (e jw )
H I (e-jw ) -1 H I (e
jw
)
H (e - jw
) tan -1
- jw
tan jw
H (e jw )
H R (e ) H R (e )
Phase response is odd function.
5. FT of a delayed Sequence
FT [h (n-k)] = h( n k )e
n
jwn
Smartworld.asia
Put n-k = m
= h(m)e
m
jw ( m k )
e jwk
jwk
= e h(m)e jwm = H (e jw )
m
6. Time Reversal
x (n) X (w)
x (-n) X (-w)
F T [x (-n)] = x ( n)e
n
jwn
Put –n = m
x
( m) e jwm
X ( w)
46
Smartzworld.com 46 jntuworldupdates.org
Smartworld.asia Specworld.in
7. Frequency Shifting
F T [x (n) e jwo n ]=
n
x (n) e jwo n e -jwn
=
n
x (n) e j ( w wo ) n = X (w-wo)
8. a. Convolution
x1 (n) * x2 (n) X1(w) X2(w)
n
[x1 (n) * x2 (n) ] e-jwn =
n k
[ x1 (k) x2 (n-k) ] e-jwn
Put n-k = m
Smartworld.asia
= x1 (k) [x2(m)] e-jw (m+k)
n m
=
n
x1 (k) e -jwk
m
[x2(m)] e-jwm
= X1(w) X2(w)
1
b. [X1(w) * X2(w)] x1 (n) x2 (n)
2
9. Parsevals Theorem
1
n
*
x1(n) x2 (n) =
2
[X1(w) X2*(w)] dw
dX ( w)
n x (n) j
dw
10.F T of Even Symmetric Sequence
H (e
jw
)=
n
h (n) e-jwn
47
Smartzworld.com 47 jntuworldupdates.org
Smartworld.asia Specworld.in
1
=
n
h (n) e-jwn + h (0) + n 1
h (n) e-jwn
Let n = -m
=
m 1
h (-m) e jwm
+ h (0) + n 1
h (n) e-jwn
frequency
0 ; H (e jw ) >0
; H (e jw ) <0
11.F T of Odd Symmetric Sequence
For odd sequence h (0) = 0
Smartworld.asia
h (n) [e - e ]
H (e jw ) =
n 1
-jwn jwn
= -j 2 n 1
h (n) Sin (wn) HI (e jw ) is a imaginary valued function
H (e jw ) = HI (e jw ) for HI (e jw ) > 0
= - HI (e jw ) for HI (e jw ) < 0
H (e jw ) For w over which HI (e jw ) > 0
2
= for w over which HI (e jw ) < 0
2
2
1
12. x(0) = 2 X (w)dw
0
Central Co-ordinates
48
Smartzworld.com 48 jntuworldupdates.org
Smartworld.asia Specworld.in
X (0) = x ( n)
n
13. Modulation
X ( w w0 ) X ( w w0 )
Cos (won) x (n)
2 2
FOURIER TRANSFORM OF DISCRETE TIME SIGNALS
X (w) =
n
x (n) e-jwn
F T exists if x(n)
n
Smartworld.asia
=0 otherwise
1
1
Sol: H (e jw ) = e
n 1
3
jwn
=
1 jw
3
e 1 e jw =
1
3
1 2Cos ( w)
w
0 1
1
2 3
1
-
3
49
Smartzworld.com 49 jntuworldupdates.org
Smartworld.asia Specworld.in
) = a e jwn
n
jw
H (e
n 0
1
= (ae
n 0
jw n
) =
1 ae jw
Q. x(n) = n n u(n) <1
d 1
j
dw 1 e
n
n u(n) jw
e jw
= (1 e jw ) 2
1
Hint: n
u(n)
n 0
n
e jwn
= (e jw ) n
n 0
=
1 e jw
n
Smartworld.asia
Q. x(n) = 0nN
Or
x(n) = n [ u(n) – u(n-N)]
= n u(n) – N n-N u(n-N) Using Shifting Property
1 e jwN
[
N
]
X(w) =
1 e jw
1 e jw
1 (e jw ) N
=
1 e jw Ans
Q. x(n) = n
1 two sided decaying exponential
x(n) = n u(n) + -n u(-n) - (n) using folding property
1 1 1 2
1 =
=
1 e jw 1 e jw 1 2Cosw 2
Q. x (n) = u (n) Since u (n) is not absolutely summable
50
Smartzworld.com 50 jntuworldupdates.org
Smartworld.asia Specworld.in
1
we know that u (t) ( w) jw
1
(w)
Similarly X (w) =
1 e jw +
Smartworld.asia
51
Smartzworld.com 51 jntuworldupdates.org
Smartworld.asia Specworld.in
Since X (w) is periodic with period 2 , sample X(w) periodically with N equidistance
2
samples with spacing w .
N
Smartworld.asia
K = 0, 1, 2…..N-1
2
2k j
Kn
X x ( n )e N
N n
The summation can be subdivided into an infinite no. of summations, where each sum
contains
N 1 2
2 j
2k
x(n)e
1 Kn
j
............ x(n)e
Kn N
X N
+
N n N n 0
2 N 1 2
j
x(n)e
Kn
N
..................
n N
52
Smartzworld.com 52 jntuworldupdates.org
Smartworld.asia Specworld.in
lN N 1 2
j
n
Kn
N
x(n)e
=
lN
l
Put n = n-lN
x(n lN )e
N 1 2
j K ( n lN )
N
=
l n 0
2
j
l
N 1 Kn
=
x(n lN )e N
n 0
N 1 2
j
Kn
N
X(k) = xp(n) e
n 0
N 1 2
j Kn
N
We know that xp(n) = Ck e n= 0 to N-1
Smartworld.asia
k 0
N 1 2
Ck=
1
N
n 0
xp(n) e
j
N
Kn
k=0 to N-1
1
Therefore Ck= X(k) k=0 to N-1
N
N 1
2
j Kn
IDFT ------------ xp (n) =
1
N
k 0
X(k) e N
n = 0 to N-1
This provides the reconstruction of periodic signal xp(n) from the samples of spectrum
X(w).
The spectrum of aperiodic discrete time signal with finite duration L<N, can be exactly
2k
recovered from its samples at frequency Wk= .
N
Prove: x(n) = xp (n) 0 n N-1
53
Smartzworld.com 53 jntuworldupdates.org
Smartworld.asia Specworld.in
Using IDFT
N 1 2
1
j Kn
x (n) = X(k) e N
N k 0
N 1 N 1 2
1
j Kn
X (w) = [ X (k) e N
] e-jwn
n 0 N k 0
N 1 N 1 2
1 jn ( w
K)
= X (k) [ e N
]
k 0 N n 0
N 1
1
If we define p(w) =
N
n 0
e-jwn
wN
Smartworld.asia
N 1 Sin
1 1 e 2
jwN
jw
2
= = e
N 1 e jw w
NSin
2
N 1
2k
Therefore: X (w) = X (k) P(w- )
k 0 N
2k
At w = P (0) =1
N
2k
And P (w- ) = 0 for all other values
N
N 1 N 1
2k
X (w) = X(k) = X( )
k 0 k 0 N
54
Smartzworld.com 54 jntuworldupdates.org
Smartworld.asia Specworld.in
0
xp (n) = x(n LN )
l
a
l
n lN
n
a
= a n a lN 0 n N-1
l 0 1 aN
Smartworld.asia
If we define aliased finite duration sequence x(n)
xˆ (n) x p (n) 0 n N-1
=0 otherwise
N 1 N 1
Xˆ ( w) xˆ (n)e jwn
n 0 = x
n 0
p (n)e jwn
N 1
an N 1
=
1
n 0 1 a
N
e jwn =
1 aN
(ae
n 0
jw n
)
1 1 a N e jwN
Xˆ ( w)
1 a N 1 a e jw
55
Smartzworld.com 55 jntuworldupdates.org
Smartworld.asia Specworld.in
2k
j N
2K 1 1 a N
e N
Xˆ N 2K
N 1 a 1 a e j N
1 2K
= j 2k = X
1 ae N N
2k
Although Xˆ (w) X ( w), the samples at Wk= are identical.
N
1 1
Ex: X (w) = & X (k) = 2
j
1 a e jw
k
1 a e N
Apply IDFT
2nk
j
N 1
e
N
1
x (n) = N j
2k using Taylor series expansion
k 0
1 ae N
Smartworld.asia
j 2Nnk r j 2Nkr
N 1
1
= N e
k 0
a e
r 0
1 N 1 j 2k ( nNr )
=
N
a e
r
r 0 k 0
=0 except r = n+mN
x (n) = a
m 0
n mN
= a
n
(a
m 0
N
)m
an
=
1 aN
The result is not equal to x (n), although it approaches x (m) as N becomes .
56
Smartzworld.com 56 jntuworldupdates.org
Smartworld.asia Specworld.in
3 2
j
x ( n )e
n
4
X (1) = = -2+2j
n 0
X (2) = -2
X (3) = -2-2j
DFT as a linear transformation
2
j
Let WN e N
N 1
X (k) =
nk
x(n)W N k = 0 to N-1
n 0
N 1
1
x (n) =
N
X (k )W
k 0
nk
N n = 0, 1…N-1
x ( 0)
Smartworld.asia
X ( 0)
x(1)
X (1)
Let xN = XN =
x( N 1) X ( N 1)
1 1 1 1
1 W 1 W 2
W N( N 1)
N N
1 W N2 W N4 W N2 ( N 1)
WN =
1 W NN 1 W N2 ( N 1) WN( N 1)( N 1)
57
Smartzworld.com 57 jntuworldupdates.org
Smartworld.asia Specworld.in
DFT IDFT
1
XN = WN xN xN = W N* X N
N
x N WN1 X N
1. WNK N WNK
N
1 1 K
W N WN* 2. WN 2
WNK
N
1 1 1 1 1 1 1 1 1 1 1 1
1 W 1 W 2 W 3 1 W 1 W 2 W 3 1 j 1 j
4 4 4 4 4 4
DFT W4 = 1 W 2 W 4 W 6 = 1 W4 W4 W42
2 0 = 1 1 1 1
1
4 4 4
9
1 j 1 j
3 6 3 2
1 W4 W4 W4 1 W4 W4 W4
1 1
Smartworld.asia
1 1 0
1 j 1 j 1
X4 = W4 x 4 = 1 1 1 1 2
6
2 2 j
= 2
1 j 1 j 3 2 2 j
IDFT
0
1 1 1 1 6 1
1 j 1 j 2 2 j
1 * 1
x4 = WN X N = 2 = 2 Ans
4 4 1 1 1 1
1 j 1 j 2 2 j 3
Q.
x (n) = { 1,0.5}
h (n) = { 0.5,1 }
58
Smartzworld.com 58 jntuworldupdates.org
Smartworld.asia Specworld.in
Find y (n) = x (n) h (n) using frequency domain. Since y (n) is periodic with period 2.
Find 2-point DFT of each sequence.
X (0) = 1.5 H (0) = 1.5
X (1) = 0.5 H (1) = -0.5
Y (K) = X (K) H (K)
Y (0) = 2.25 Y (1) = -0.25
Smartworld.asia
Using IDFT y (0) = 1; y (1) = 1.25
~y (n) h (n) ~x (n) h~(k ) ~x (n k )
~
k
~
=
~
x
k
( k ) h (n k )
~
~
y (0) = ~
x (
k
k ) h (k )
~ ~ ~ ~
= x (0)h (0) x (1)h (1)
= 1 * 0.5 + 0.5 * 1 = 1
~
~
y (1) = ~
x (
k
k ) h (1 k )
59
Smartzworld.com 59 jntuworldupdates.org
Smartworld.asia Specworld.in
~ ~ ~ ~
= x (0)h (1) x (1)h (0)
= 1 * 1 + 0.5 * 0.5 = 1.25
~ ~
y (2) = ~
x (
k
k ) h (2 k )
~ ~ ~ ~
= x (0)h (2) x (1)h (1)
= 1 * 0.5 + 0.5 * 1 = 1
~
y ( n) = {1, 1.25, 1, 1.25…..}
Q. Find Linear Convolution of same problem using DFT
Sol. The linear convolution will produce a 3-sample sequence. To avoid time
aliasing we convert the 2-sample input sequence into 3 sample sequence by padding with
zero.
For 3- point DFT
X (0) = 1.5
Smartworld.asia H (0) = 1.5
2
j
2 j
3
X (1) = 1+0.5 e 3
H (1) = 0.5+ e
4 4
j j
3
X (2) = 1+0.5 e H (2) = 0.5+ e 3
60
Smartzworld.com 60 jntuworldupdates.org
Smartworld.asia Specworld.in
y(0) = 0.5
y(1) =1.25
y(2) =0.5
y(n) = { 0.5, 1.25, 0.5} Ans
PROPERTIS OF DFT
1. Linearity
If h(n) = a h1(n) + b h2(n)
H (k) = a H1(k) + b H2(k)
2. Periodicity H(k) = H (k+N)
~
3.
h ( n) h(n mN )
m
4. y(n) = x(n-n0)
2kn0
j
N
Y (k) = X (k) e
Smartworld.asia
5. y (n) = h (n) * x (n)
Y (k) = H (k) X (k)
6. y (n) = h(n) x(n)
Y (k) =
1
H (k ) X (k )
N
7. For real valued sequence
N 1
2kn
H R (k ) h(n)Cos
n 0 N
N 1
2kn
H I (k ) h(n) Sin
n 0 N
a. Complex conjugate symmetry
h (n) H(k) = H*(N-k)
h (-n) H(-k) = H*(k) = H(N-k)
61
Smartzworld.com 61 jntuworldupdates.org
Smartworld.asia Specworld.in
H (k ) H ( N k )
e. Phase function is odd function
H (k ) H ( N k )
f. Smartworld.asia
If h(n) = h(-n)
H (k) is purely real
g. If h(n) = -h(-n)
H (k) is purely imaginary
8. For a complex valued sequence
x*(n) X*(N-k) = X*(-k)
N 1
N 1
X*(k) = x
n 0
*
( n)W N n k
N 1
*
X (N-k) = x
n 0
*
(n)W Nnk = X*(-k)
N 1
DFT [x*(n)] = x
n 0
*
(n)W Nnk = X*(N-k) proved
Smartzworld.com 62 jntuworldupdates.org
Smartworld.asia Specworld.in
9. Central Co-ordinates
N 1
1
X (k )
N 1
1
x (0) =
N k 0
x(
N
2
)=
N
(1)
k 0
k
X (k ) N=even
N 1 N 1
X (0) = x ( n)
n 0
N
X( )=
2
(1)
n 0
n
x ( n) N=even
10.Parseval’s Relation
N 1 N 1
2 2
N
x ( n) X (k )
n 0 k 0
N 1
Proof: LHS N x ( n) x * ( n)
n 0
1
N 1 N 1
= N x(n) X *
( k )WNnk
m 0 N k 0
N 1
N 1
X *
( k ) x ( n)W Nn k
Smartworld.asia
=
k 0 n 0
N 1 N 1 2
= X
k 0
*
( k ) X (k) =
k 0
X (k )
x((n)) N x( N n) X ((k )) N X ( N k )
Reversing the N-point seq in time is equivalent to reversing the DFT values.
x( N
n
DFT n)e N
n 0
Let m=N-n
N 1 j 2k
( N m )
= x ( m)e
n 0
N
m=1 to N = 0 to N-1
N 1 j 2k
x ( m) e
m
N
=
m 0
63
Smartzworld.com 63 jntuworldupdates.org
Smartworld.asia Specworld.in
N 1 j 2m
( N k )
= x(m)e
m 0
N
= X(N-k)
N 1 j 2k
n 0
l 1 j 2k N 1 j 2k
x(n l )
n
x(n l )
n
N
= N e + N e N
n 0 n l
N 1 j 2k
j 2k
x ( N n l )e
l 1 n
x( N n l )
n N
N
= e +
n 0 n l
Put N+n-l = m
x(m)Smartworld.asia
N 1 j 2k 2 N 1l j 2k
( m l ) ( m l )
+
N
e x(m)e N
=
m N l m N
N to 2N-1-L is shifted to N 0 to N-1-L
Therefore 0 to N-1 = (0 to N-1-L) to ( N-L to N-1)
N 1 2k
j ( m l )
Therefore
x ( m) e
m 0
N
2k 2k
N 1 j j l
x ( m) e
m
N N
=
m 0
e
2k
j l
N
= X(k) e RHS
13.Circular Frequency Shift
64
Smartzworld.com 64 jntuworldupdates.org
Smartworld.asia Specworld.in
2l
j n
x ( n )e N
X (k l ) N
2l N 1 2l 2k
n j
x ( n)e
j j n n
N N
DFT x ( n ) e N
= e
n 0
N 1 2n
j ( k l )
= x ( n )e
n 0
N
= X (k l ) N RHS
14.x(n) X(k)
k
{x(n), x(n), x(n)…….x(n)} M X ( )
m
(m-fold replication)
n
x( ) { X (k ), X (k ),...... X (k )} (M- fold replication)
m
Smartworld.asia
2, 3, 2, 1 8, -j2, 0, j2
Zero interpolated by M
{2, 3, 2, 1, 2, 3, 2, 1, 2, 3, 2, 1} {24, 0, 0, -j6, 0, 0, 0, 0, 0, j6, 0, 0}
15.Duality
x(n) X(k)
X(n) N x(N-k) 0 K N 1
N 1 2
1
j n
x(n) =
X ( )e N
N 0
N 1 2
1 ( N k )
j
x(N-k) =
X ( )e N
N 0
N 1 2
1 j
k
=
X ( )e N
N 0
65
Smartzworld.com 65 jntuworldupdates.org
Smartworld.asia Specworld.in
N 1 2
j
k
N x(N-k) =
X ( )e N
0
N 1 2k
j
X ( n )e
n
N
= = DFT [ X(n) ] LHS proved
n 0
16.Re[x(n)]
X ep (k ) 1
X ep (k ) = X ((k )) N X * ((k )) N
2
j Im[x(n)]
X op (k )
xep (n) Re[X(k)]
xop (n) j Im[X(k)]
xep (n) Even part of periodic sequence = 1 x(n) x((n)) N
Smartworld.asia
2
Proof: X(k) = x
n 0
( n )W nk
N
N 1
X(N-k) = x(n)W
n 0
nk
N X ((k )) N
N 1
X (k) =
* x *
( n)W N nk
n 0
N 1
*
X (N-k) = x
n 0
*
( n )WN
nk
X *
((k )) N
66
Smartzworld.com 66 jntuworldupdates.org
Smartworld.asia Specworld.in
X ((k )) N X * ((k )) N 1 N 1
2
x(n) x * (n) WNnk
2 n 0
= DFT of [Re[x (n)]] LHS
N 1 N 1
17. x
n 0
1 ( n) x ( n) =*
2
1 X
N k 0
1 ( k ) X 2* ( k )
Y(k) =
1
N
X 1 (k ) X 2* (k )
X
N 1
1
= 1 (l ) X 2* (k l )
N l 0
X
N 1
1
Y(0) = 1 (l ) X 2* (l )
N l 0
Smartworld.asia
Using central co-ordinate theorem
N 1
Y(0) = x ( n) x ( n)
n 0
1
*
2
N 1 N 1
Therefore X
*
x ( n) x 1 2 ( n) =
1
1 (k ) X 2* ( k )
n 0 N k 0
QUESTIONS
1 Q. (i) {1,0,0,…….0} (impulse) {1,1,1…..1} (constant)
(ii) {1,1,1,……1} (constant) ) {N,0,0,…….0} (impulse)
j 2k
N 1 n
jN2k
1 ( j 2k)
NN
1
e
N
(iii)
n
j 2k
k 0 1 N
1 e N
2nko
(iv) Cos
N
(k k o ) (k ( N k o )
N 2
(Impulse pair)
67
Smartzworld.com 67 jntuworldupdates.org
Smartworld.asia Specworld.in
Sol. x(n) =
2
j 2nko j 2n ( N k o )
e N
e N
=
2
We know that 1 N (k )
j 2nKo
x ( n) e N
X ( K Ko)
x(n)
N
(k k o ) (k ( N k o )
2
I. Inverse DFT of a constant is a unit sample.
II.
Smartworld.asia
DFT of a constant is a unit sample.
2 Q. Find 10 point IDFT of
X(k) = 3 k=0
=1 1k9
3 Q. Suppose that we are given a program to find the DFT of a complex-valued sequence
x(n). How can this program be used to find the inverse DFT of X(k)?
N 1
X(k) = x
n 0
( n )W nk
N
68
Smartzworld.com 68 jntuworldupdates.org
Smartworld.asia Specworld.in
N 1
x(n) =
1
N k 0
X ( k )W nk
N
N 1
N x*(n) = X
k 0
*
( k )W nk
N
1. Conjugate the DFT coefficients X(k) to produce the sequence X*(k).
2. Use the program to fing DFT of a sequence X*(k).
3. Conjugate the result obtained in step 2 and divide by N.
4 Q. xp(n) = { 1
, 2, 3, 4, 5, 0, 0, 0}
5 Q. Smartworld.asia
(iii) hp(n) = xp(-n) = {1, 0, 0, 0, 5, 4, 3, 2}
x(n) = {1, 1, 0, 0, 0, 0, 0, 0} n = 0 to 7 Find DFT.
1 j 2k jk
x ( n)e
n
8 4
X(k) =
n 0
=1+ e k = 0 to 7
X(0) = 1+1 = 2
j
4
X(1) = 1+ e = 1.707 - j 0.707
j
2
X(2) = 1+ e = 1- j
j 3
4
X(3) = 1+ e = 0.293 - j 0.707
X(4) = 1-1 = 0
By conjugate symmetry X(k) = X*(N-k) = X*(8-k)
X(5) = X*(3) = 0.293 + j 0.707
69
Smartzworld.com 69 jntuworldupdates.org
Smartworld.asia Specworld.in
Smartworld.asia
(iii) g(n) = x(-n) = 1, 0, 1, 2
G(k) = X(-k) = X*(k) = {4, j2, 0, -j2}
(iv) p(n) = x*(n) = {1, 2, 1, 0}
P(k) = X*(-k) = {4, j2, 0, -j2}* = {4, -j2, 0, j2}
(v) h(n) = x(n) x(n)
= {1, 4, 1, 0}
H(k) =
1
X (k ) X (k ) = 1 [ 24, -j16, 0, j16] = {6, -j4, 0, j4}
4 4
(vi) c(n) = x(n) x(n)
= {1, 2, 1, 0} {1, 2, 1, 0} = {2,4,6,4}
C(k) = X(k)X(k) = {16, -4, 0, -4}
(vii) s(n) = x(n) x(n) = {1, 4, 6, 4, 1, 0, 0}
S(k) = X(k) X(k) = {16, -2.35- j 10.28, -2.18 + j 1.05, 0.02 + j 0.03, 0.02 - j 0.03, -2.18 -
j 1.05, -2.35 + j 10.28}
(viii) x(n) 1 4 1 0 6
2
70
Smartzworld.com 70 jntuworldupdates.org
Smartworld.asia Specworld.in
1 1
[16 4 4] 6
2
X ( k )
4 4
Smartworld.asia
71
Smartzworld.com 71 jntuworldupdates.org
Smartworld.asia Specworld.in
X(k) = x(n)W
n 0
nk
N 0 K N 1
N 1
nk nk
= { Re[x(n)] + j Im[x(n)] } { Re( WN ) + j Im( WN ) }
n 0
N 1 N 1
=
n 0
Re[x(n)] Re( W ) - nk
N n 0
Im[x(n)] Im( WN ) +
nk
N 1
n 0
2
Direct evaluation of X(k) requires N complex multiplications and N(N-1) complex
additions.
4 N2 real multiplications
{ 4(N-1) + 2} N = N(4N-2) real additions
Smartworld.asia
The direct evaluation of DFT is basically inefficient because it does not use the symmetry
N
K
WNK N
nk nk
& periodicity properties WN W W 2
N & N
DITFFT:
N N
1 1
2 2
X(k) = x(2n)W
n 0
2 nk
N + x(2n 1)W
n 0
( 2 n 1) k
N
(even) (odd)
N
N
1 1
2
x
2
= x (n)W e
2 nk
N + WN
K
o (n)WN2 nk
n 0 n 0
N N
1 1
2
x
2
=
x (n)W e
nk
N /2 W
+ N
K
o (n)WNnk/ 2
n 0 n 0
K
= Xe(k) + W N Xo(k)
72
Smartzworld.com 72 jntuworldupdates.org
Smartworld.asia Specworld.in
Although k=0 to N-1, each of the sums are computed only for k=0 to N/2 -1, since Xe(k)
& Xo(k) are periodic in k with period N/2
N
K K
For K N/2 WN 2
=- W N
X(k) for K N/2
N
K
2
X(k) = Xe(k-N/2) - W N Xo(k-N/2)
N=8
x(2n) = xe(n) ; x(2n+1) = xo(n)
xe(0) = x(0) xo(0) = x(1)
xe(1) = x(2) xo(1) = x(3)
xe(2) = x(4) xo(2) = x(5)
xe(3) = x(6) xo(3) = x(7)
73
Smartzworld.com 73 jntuworldupdates.org
Smartworld.asia Specworld.in
Smartworld.asia
N N
This pt DFT can be expressed as combination of pt DFT.
2 4
2k N
Xe(k) = Xee(k) + WN Xeo (k ) k = 0 to -1 (0 to 1)
4
N
2( k ) N
N W 4
Xeo (k ) N N
= Xee(k- )- N k= to -1 ( 2 to 3 )
4 4 4 2
74
Smartzworld.com 74 jntuworldupdates.org
Smartworld.asia Specworld.in
0
Xe(0) = Xee(0) + W8 Xeo(0) ; xee(0) = xe(0) = x(0)
2
Xe(1) = Xee(1) + W8 Xeo(1) ; xee(1) = xe(1) = x(2)
0
Xe(2) = Xee(0) - W8 Xeo(0) ; xeo(2) = xe(2) = x(4)
2
Xe(3) = Xee(1) - W8 Xeo(1) ; xeo(3) = xe(3) = x(6)
Where Xee(k) is the 2 point DFT of even no. of x e(n) & Xeo(k) is the 2 point DFT of odd
no. of xe(n)
Similarly, the sequence xo(n) can be divided in to even & odd numbered sequences as
xoe(0) = xo(0) = x(1)
xoe(1) = xo(2) = x(5)
xoo(0) = xo(1) = x(3)
xoo(1) = xo(3) = x(7)
W82 Xoo(1) ;
Smartworld.asia
Xo(1) = Xoe(1) +
0
Xo(2) = Xoe(0) - W 8 Xoo(0) ;
2
Xo(3) = Xoe(1) - W8 Xoo(1) ;
Xoe(k) is the 2-pt DFT of even-numbered of xo(n)
Xoo(k) is the 2-pt DFT of odd-numbered of xo(n)
Xee(0) = xee(0) + xee(1) = xe(0) + xe(2) = x(0) + x(4)
Xee(1) = xee(0) - xee(1) = xe(0) - xe(2) = x(0) - x(4)
75
Smartzworld.com 75 jntuworldupdates.org
Smartworld.asia Specworld.in
Smartworld.asia
76
Smartzworld.com 76 jntuworldupdates.org
Smartworld.asia Specworld.in
Smartworld.asia
No. of No. of Complex Speed
No. of points N Multiplications Improvement Factor:
Stages Direct N2 FFT N2
N
N Log 2 N
Log 2 N 2
2
2 4 16 4 4
3 8 64 12 5.33
4 16 256 32 8
5 32 1024 80 12.8
6 64 4096 192 21.33
For N=8
No of stages given by= Log2N = Log28 = 3.
No. of 2 i/p sets = 2( Log 2N -1 )
=4
77
Smartzworld.com 77 jntuworldupdates.org
Smartworld.asia Specworld.in
= 8 * 3 =24
Each stage no. of butterflies in the stage= 2m-q where q = stage no. and N=2m
Each butterfly operates on one pair of samples and involves two complex additions and
one complex multiplication. No. of butterflies in each stage N/2
DITFFT: ( different representation) (u can follow any one) ( both representations are
correct)
N
N
1 1
2
x(2n 1)W
2
x(2n)W 2 nk ( 2 n 1) k
X(k) = N + N
n 0 n 0
N N
1 1
2 2
= x (n)W
n 0
e
nk
N + W Nk x
n 0
o (n)WNnk/ 2
2
K
4 pt DFT Xe(k) + W N Xo(k) k= 0 to N/2 -1 = 0 to 3
N
N (K ) N
Xe(k- ) - W N 2 Xo(k- ) k = N/2 to N-1 = 4 to 7
2 2
2 pt DFT
Smartworld.asia
Xe(k) = Xee(k) + WN2 K Xeo(k)
= Xee(k-N/4) - WN
2( k
N
4
)
Xeo(k-N/4)
k = 0 to N/4-1 = 0 to 1
k = N/4 to N/2 -1 = 2 to 3
Xo(k) = Xoe(k) + WN2 K Xoo(k) k = 0 to N/4-1 = 0 to 1
N
2( k )
= Xoe(k-N/4) - WN 4
Xoo(k-N/4) k = N/4 to N/2 -1 = 2 to 3
W82 W41
N=8
X(0) = Xe(0) + W80 Xo(0) ; X(4) = Xe(0) - W80 Xo(0)
X(1) = Xe(1) + W81 Xo(1) ; X(5) = Xe(1) - W81 Xo(1)
X(2) = Xe(2) + W82 Xo(2) ; X(6) = Xe(2) - W82 Xo(2)
X(3) = Xe(3) + W83 Xo(3) ; X(7) = Xe(3) - W83 Xo(3)
78
Smartzworld.com 78 jntuworldupdates.org
Smartworld.asia Specworld.in
=
4
Xee(k) = x(4n)W
4 nk 4 nk
N
x(4n)W N
4k
=x(0) + x(4) W8
0 n 0
Xee(0) = x(0)+x(4)
Xee(1) = x(0)-x(4)
Smartworld.asia
79
Smartzworld.com 79 jntuworldupdates.org
Smartworld.asia Specworld.in
Smartworld.asia
80
Smartzworld.com 80 jntuworldupdates.org
Smartworld.asia Specworld.in
DIFFFT:
N
1
2 N 1
X(k) = x(n)W
n 0
nk
N + x ( n ' )W n 'k
N put n’ = n+N/2
n1 N / 2
N
1 N
1
2
= x( n)W
2
x(n N / 2)W
nk ( n N / 2) k
N + N
n 0 n 0
N N
1 1
2 N 2
x(n)W x(n N / 2)W
nk k nk
2
= N + W N N
n 0 n 0
N
1
2
= [ x (
n 0
n ) N W nk
+ (-1) x(n+ )] N
2
k
N
1
2
[ x(n) + x(n+ N2 )] WNnk/ 2
X(2k) =
n 0
N
1
Smartworld.asia
2
N n nk
X(2k+1) = {[ x ( n ) - x(n+ )] W N } W N / 2
n 0 2
Let f(n) = x(n) + x(n+N/2)
n
g(n) = { x(n) – x(n+N/2) } W N
81
Smartzworld.com 81 jntuworldupdates.org
Smartworld.asia Specworld.in
N=8
f(0) = x(0) + x(4)
f(1) = x(1) + x(5)
f(2) = x(2) + x(6)
f(3) = x(3) + x(7)
Smartworld.asia
82
Smartzworld.com 82 jntuworldupdates.org
Smartworld.asia Specworld.in
N
1
= Smartworld.asia
4
nk
X(4k)
[ f (n) + f(n+ N )] W N / 4
n 0 4
N
1
4
N
1
4
X(4k+1) = [ g ( n
n 0
) + g(n+
N
4
W nk
)] N / 4
N
1
4 nk
X(4k+3) = [{g ( n) - g(n+
nk
N / 2 ] WN / 4
N W
)}
n 0 4
83
Smartzworld.com 83 jntuworldupdates.org
Smartworld.asia Specworld.in
Smartworld.asia
84
Smartzworld.com 84 jntuworldupdates.org
Smartworld.asia Specworld.in
UNIT-IV
DIGITAL FILTER STRUCTURE
The difference equation
NP
a k x(n-k) + bk
M
y(n) = y(n-k)
k N F k 1
NP
a k z k Np NF
(1 C k ) Z 1
k N F
M
Z NF M
1 bk z (1 d
H(z) = k or = A
k 1 k ) Z 1
k 1 k 1
Smartworld.asia
85
Smartzworld.com 85 jntuworldupdates.org
Smartworld.asia Specworld.in
Smartworld.asia
2. Sensitivity of co-efficient to quantization effects that occur when using finite-precision
arithmetic.
Cascade Combination of second-order section (CSOS)
y(n) = x(n) + a1 x(n-1) + a2 x(n-2) + b1 y(n-1) + b2 y(n-2)
1 a1 Z 1 a2 Z 2
H(z) =
1 b1 Z 1 b2 Z 2
Ex:
86
Smartzworld.com 86 jntuworldupdates.org
Smartworld.asia Specworld.in
z 5 5 1 Z 2 z 5 1 5Z 2 1
Z 1 Z Z 3
3 12 12 12 3 4 4 4
H(z) = Z 1
Z 2 = Z 1 Z 2
1 1
2 4 2 4
z 1 1
1 Z 1 Z 1 Z 2 1 2
3 4 1 1 1 1 Z Z
= Z 1 Z 2 = z 1 Z Z 1 Z 2
1 3 4 1
2 4 2 4
Smartworld.asia
Ex:
Z Z
1
Z 2 Z
1 Z 2 Z 3
H(z) = = Z 1 Z 1 Z 1
Z 1 Z 1 Z 1
1 1 1 1 1 1
2 4 8 2 4 8
Z
0.65 0.45Z 1
Z 2 1.45 Z 1
= Z 1 Z 1 Z 1
1 1 1
2 4 8
87
Smartzworld.com 87 jntuworldupdates.org
Smartworld.asia Specworld.in
z 5 5 1 Z 2
1 5 1 5 2 Z 3
Z Z Z Z
3 12 12 12 3 12 12 12
H(z) = Z 1
Z 2 = Z 1 Z 2
1 1
2 4 2 4
Z 1 Z 2 Z 3 5 2 1 5 1 Z 1 7
1 Z Z
2 4 12 12 3 12 3 3
Z 3 Z 2 Z 1
12 6 3
___-____+____-_______
7 Z 2 Z 1 1
12 12 3
7 Z 2 7 Z 1 7
Smartworld.asia
12 6 3
______________________
5 1 7
Z
4 3
7 5 1
1 Z
Z 3 4
H(z) = Z 2 2
3 1 Z
1 Z
2 4
88
Smartzworld.com 88 jntuworldupdates.org
Smartworld.asia Specworld.in
Ex:
Z Z
Z 2 1
H(z) = obtain PSOS
Z 1 Z 1 Z 1
1 1 1
2 4 8
1 Z 1 2Z 1
A
1
B C
Z Z
1
Z = Z 1 Z 1
1 1
Z 1
1 1 1 1 1 1
2 4 8 2 4 8
A = 8/3 B = 10 C = -35/3
Smartworld.asia
Jury – Stability Criterion
N ( z)
H(z) =
D( z )
N
D(z) = b Z
N i
i = bo ZN +b1 ZN-1 + b2 ZN-2 +….. bN-1 Z1 + bN
i 0
ROWS COEFFICIENTS
1 bo b1 ……. bN
2 bN bN-1 ……. bo
3 Co C1 ……. CN-1
4 CN-1 CN-2 ……. Co
5 do d1 ……. dN-2
6 dN-2 dN-3 ……. do
89
Smartzworld.com 89 jntuworldupdates.org
Smartworld.asia Specworld.in
.
.
.
2N-3 r0 r1 r2
bo b N i
Ci = bN bi i = 0,1,…N-1
co c N 1i
di = c N 1 ci i = 0,1,…N-2
i. D(1) > 0
ii. (-1)N D(-1) > 0
iii. bo bN co c N 1 d o d N 2 ro r2
Ex:
H(z) =
Z4 Smartworld.asia
4Z 4 3Z 3 2Z 2 Z 1
D(z) = 4Z 3Z 2Z Z 1
4 3 2
1 4 3 2 1 1
2 1 1 2 3 4
3 15 11 6 1
4 1 6 11 15
5 224 159 79
D(1) = 4+3+2+1+1 = 11 > 0, (-1)4 D(-1) = 3 >0
bo b4 co c3 do d2 Stable.
Ex:
1 4Z 2
H(z) = = Ans: Unstable
7 1
1 Z 1 Z 2 4Z 2 7 Z 2
4 2
90
Smartzworld.com 90 jntuworldupdates.org
Smartworld.asia Specworld.in
UNIT-V
Non Recursive filters Recursive filters
Np M
y(n) =
k
ak x(n-k) y(n) = ak x(n-k) – bk y(n-k)
k Nf k 1
For causal i/p sequence It gives IIR o/p but not always.
N
Ex: y(n) = x(n) – x(n-3) + y(n-1)
y(n) =
k 0
ak x(n-k)
NP
FIR filters
Smartworld.asia
1. Linear phase no phase distortion.
IIR filters
Linear phase, phase distortion.
2. Used in speech processing, data Graphic equalizers for digital audio,
transmission & correlation processing tone generators filters for digital
telephone
3. Realized non recursively. Realized recursively.
4. stable Stable or unstable.
H(n) = an u(n) a<1 stable
= 0 a>1 unstable
5. filter order is more Less
6. more co-efficient storage Less storage
7. Quantization noise due to finite Quantization noise
precision arithmetic can be made
negligible
8. Co-efficient accuracy problem is More
91
Smartzworld.com 91 jntuworldupdates.org
Smartworld.asia Specworld.in
less severe
9. used in multirate DSP (variable
sampling rate)
IIR FILTER DESIGN
Butterworth, chebyshev & elliptic techniques.
Impulse invariance and bilinear transformation methods are used for translating s-
plane singularities of analog filter to z-plane.
Frequency transformations are employed to convert LP digital filter design into HP,
BP and BR digital filters.
All pass filters are employed to alter only the phase response of IIR digital filter to
approximate a linear phase response over the pass band.
The system function = H(s)
The frequency transfer function = H(j ) = H(s) / s=j
The power transfer function = H ( j) = H(j ) H*(j ) = H(s) H(-s) / s=j
2
Smartworld.asia
To obtain the stable system, the polse that lie in the left half of the s-plane are assigned to
H(s).
BUTTERWORTH FILTER DESIGN
1
The butterworth LP filter of order N is defined as HB(s) HB(-s) = 2N
s
1
j c
Where s = j c
1
H B ( j c ) = H B ( j c ) db = -3dB ‘s
2
or
2
It has 2N poles
2N
s
1 =0
j c
2N
s
= -1
c
j
92
Smartzworld.com 92 jntuworldupdates.org
Smartworld.asia Specworld.in
j
j
= e (e c )
2N j 2N
j
e j 2 m
2N
2
= c e e 2
1 N 2 m
2N j
2N
S = c e
1 N 2 m
j
2N
Sm = c e 0 m 2N 1
1
Vo ( s ) CS 1
Vi ( s ) 1 1 RCS
R
CS
1 1 1
c
RS s 2
1
c 1
Smartworld.asia
c
Poles that are let half plane are belongs to desired system function.
1
H B ( j) =
2
2N
1
c
For a large , magnitude response decreases as -N, indicating the LP nature of this
filter.
93
Smartzworld.com 93 jntuworldupdates.org
Smartworld.asia Specworld.in
2N
= -10 log10(1 )
c
As
= -20 N log10
= -20 N dB/ Decade = -6 N dB/Octane
As N increases, the magnitude response approaches that of ideal LP filter.
The value of N is determined by Pass & stop band specifications.
Smartworld.asia
Ex: Design Butterworth LPF for the following specifications.
Pass band:
-1< H ( j) dB 0
2
for 0 1404 ( p = 1404 )
Stop band:
H ( j) dB < -60
2
for 8268 ( s = 8268 )
If the c is given
2N
s
H ( js) = [ 1
2
]-1 < 10-6 (-60dB)
c
log(10 6 1)
=N> s
2 log( )
c
Since c is not given, a guess must be made.
94
Smartzworld.com 94 jntuworldupdates.org
Smartworld.asia Specworld.in
The specifications call for a drop of -59dB, In the frequency range from the edge of the
pass band (1404 ) to the edge of stop band (8268 ). The frequency difference is equal to
s 10
6
2N Smartworld.asia
> c => 1470.3 > c
c <1470.3
Let c =1470.3
At this c it should satisfy pass band specifications.
2N
p
H B ( jp) = [ 1
2
]-1 > 0.794 (= -1dB)
c
= 0.59
This result is below the pass band specifications. Hence N=4 is not sufficient.
Let N=5
6
c < s X 10 2N
= 2076.8
10
1404 -1
In the pass band H B ( jp) = [ 1
2
] = 0.98
2076
Since N=5
c = 2076
95
Smartzworld.com 95 jntuworldupdates.org
Smartworld.asia Specworld.in
S1 = -2076
j144
S2, 3 = 2076 (cos (4 /5) j sin(4 /5)) = 2076 e
j108
S4, 5 = 2076 (cos (3 /5) j sin(3 /5)) = 2076 e
2076 5
HB(s) = s 2076 s 2 3359s (2076 ) 2 s 2 1283s (2076 ) 2
Smartworld.asia
1. Magnitude response is smooth, and decreases monotonically as increases from 0 to
2. the magnitude response is maximally flat about =0, in that all its derivatives up to
order N are equal to zero at =0
Ex: c=1, N=1
H B ( j) = (1+ )
2 2 -1
d 2
96
Smartzworld.com 96 jntuworldupdates.org
Smartworld.asia Specworld.in
N
3. The phase response curve approaches for large , where N is the no. of poles of
2
butterworth circle in the left side of s-plane.
Advantages:
1. easiest to design
2. used because of smoothness of magnitude response .
Disadvantage:
Relatively large transition range between the pass band and stop band.
Other procedure
Avo
When c = 1 Avs = 2N
w
1
wo
2 Avo
H B (s) = 2N
s
1
j
2N
k=1,2,….2N
If N is odd
S2n =1 = e j 2k
Sk = e j 2k / N k=0,1,2….(2N-1)
1
T(s) = ( N 1) / 2
where k =k
N
( s 2 2Cos k s 1)
k 1
97
Smartzworld.com 97 jntuworldupdates.org
Smartworld.asia Specworld.in
k 1
1
2n
1
10 log = K1 10 10 1
1 2 N c
1
c
k 2
2
2n
1
10 log = K2 10 10
1
2 2 N c
1
c
1 10 1
Dividing k 2
2
2n
Smartworld.asia
k1
10
10 10 1
10k1
10 1
log 10 k 2
10 10 1
n=
1
2 log 10
2
choosing this value for n, results in two different selections for c . If we wish to satisfy
our requirement at 1 exactly and do better than our req. at 2 , we use
1 2
c = 1
or c = 1
for better req at 2
k1
2n
k2
2n
10 10
1 10 10
1
End
CHEBYSHEV FILTER DESIGN
98
Smartzworld.com 98 jntuworldupdates.org
Smartworld.asia Specworld.in
2 2 S
1
Defined as Hc(S) Hc(-S) = 1 C N
jp
Smartworld.asia
3 4x3-3x
4 8x4- 8x2 +1
Two features of Chebyshev poly are important for the filter design
1. C N (x) 1 for x 1
1
2 1
H c ( j) 2 1 for 0 p
99
Smartzworld.com 99 jntuworldupdates.org
Smartworld.asia Specworld.in
2. x 1, C N (n) Increases as the Nth power of x. this indicates that for >> p , the
magnitude response decreases as -N, or -6N dB Octane. This is identical to Butterworth
filter.
Now the ellipse is defined by major & minor axis.
Define = 1 1 2
N1 1
N
Minor r = p
2
N1 1
N
Major R = p N = Order of filter.
2
SP = r Cos +j R Sin
Smartworld.asia
Ex:
Pass band:
-1< H ( j) dB 0
2
for 0 1404
Stop band:
H ( j) dB < -60
2
for 8268
10 log 1 2
1
> -1dB -1dB = 0.794
= 0.508
100
1
s 10 6 1 2
Since 5.9 CN(5.9) > = 1969
p
2
Evaluating
C3(5.9) = 804 C4(5.9) = 9416 therefore N = 4 is sufficient.
Since this last inequality is easily satisfied with N=4 the value of can be reduced to as
small as 0.11, to decrease pass band ripple while satisfying the stop band. The value =0.4
provides a margin in both the pass band and stop band. We proceed with the design with
=0.508 to show the 1dB ripple in the pass band.
Axes of Ellipse:
=0.508-1 + (1+0.508-2)1/2 = 4.17
1404 1 1
Smartworld.asia
R= 4.17 4.17 702 (1.43 0.67) 1494
4 4
2
1404
1
1
Chebyshev filter poles are closer to the j axis, therefore filter response exhibits a
ripple in the pass band. There is a peak in the pass band for each pole in the filter, located
approximately at the ordinate value of the pole.
101
Exhibits a smaller transition region to reach the desired attenuation in the stop band,
when compared to Butterworth filter.
Phase response is similar.
Because of proximity of Chebyshev filter poles to j axis, small errors in their
locations, caused by numerical round off in the computations, can results in significant
changes in the magnitude response. Choosing the smaller value of will provide some
margin for keeping the ripples within the pass band specification. However, too small a
value for may require an increase in the filter order.
It is reasonable to expect that if relevant zeros were included in the system function, a
lower order filter can be found to satisfy the specification. These relevant zeros could serve
to achieve additional attenuation in the stop band. The elliptic filter does exactly this.
IMPULSE INVARIANCE METHOD
H(z) = h( n) Z
n 0
n
Smartworld.asia
e ST ) = h(n )e
STn
H(z) (at z =
102
If the real part is same, imaginary part is differ by integral multiple of 2 , this is the
T
biggest disadvantage of Impulse Invariance method.
sa sa
Let HA(S) = =
s a b
2 2
s a jb s a jb
hA(t) = e atCosbt for t 0 s1 = -a-jb
=0 otherwise s2 = -a+jb
h (nTs) = e anTsCos(bnTs) for n 0
1 e aTsCos (bTs) Z 1 1 e aTsCos(bTs) Z 1
H(z) = =
1 2e aTsCos (bTs) Z 1 Z 2 (1 e ( a jb )Ts Z 1 )(1 e ( a jb )Ts Z 1 )
The pole located at s=p is transformed into a pole in the Z-plane at Z = e pTs , however, the
finite zero located in the s-plane at s= -a was not converted into a zero in the z-plane at Z =
e aTs , although the zero at s= was placed at z=0.
Smartworld.asia
103
k
=
(1 1.69Z 0.743Z )(1 1.707 Z 1 0.88Z 2 )
1 2
1 Z 1
S=
Ts
Smartworld.asia
Or
Using forward-difference mapping based on first order approximation Z = e sTs 1+STs
Z 1
S=
Ts
Using backward- difference mapping is based on first order approximation
Z 1 e sTs 1 STs
Z 1 1 Z 1
S =
ZTs Ts
d 2x d dx
/t=nTs = / t nTs
dt 2
dt dt
104
2
1 2Z 1 Z 2 1 Z 1
S 2
=
Ts 2 Ts
k
1 Z 1
k
Therefore S =
T
1 Z 1
Therefore H(z) = Ha(s) /s= using backward difference
T
1 0.5(1 STs)
Z= = 0.5 +
1 STs 1 STs
1 1 jTs
= =
1 jTs 1 Ts 1 2Ts 2
2 2
0.5(1 STs)
Z - 0.5 =
(1 STs)
Smartworld.asia
z 0.5 0.5 is mapped into a circle of radius 0.5, centered at Z=0.5
Using Forward-difference
Z 1
S= Z=1+STs
Ts
u+jv = 1+ ( j) Ts
if =0 u=1 and j axis maps to Z=1
If >0, then u>1, the RHS-plane maps to right of z=1.
If <0, then u<1, the LHS-plane maps to left of z=1.
105
Bilinear Transformation
Provides a non linear one to one mapping of the frequency points on the jw axis in s-
plane to those on the unit circle in the z-plane.
This procedure also allows us to implement digital HP filters from their analog
counter parts.
2 Z 1 2 1 Z 1
S= =
Smartworld.asia
Ts Z 1 Ts 1 Z 1
{Using trapezoidal rule y(n)=y(n-1)+0.5Ts[x(n)+x(n-1)]
H(Z)=2(Z-1) / [Ts(Z+1)] }
2 Z 1
To find H(z), each occurrence of S in HA(s) is replaced by
Ts Z 1
STs
1
And Z = 2
STs
1
2
1/ 2
2 Ts 2 j tan 1
Ts
Ts 1 e 2
j 1 2
e jw 2
Ts = 1/ 2
j 1 2 Ts
2
j tan 1
Ts
2
2
1 e
2
Ts
j 2 tan 1 Ts
e jw
e 2
w=2tan-1
2
106
The entire j axis in the s-plane - <j < maps exactly once onto the unit circle -
w such that there is a one to one correspondence between the continuous-time and
discrete time frequency points. It is this one to one mapping that allows analog HPF to be
implemented in digital filter form.
As in the impulse invariance method, the left half of s-plane maps on to the inside of the
unit circle in the z-plane and the right half of s-plane maps onto the outside.
2 w
In Inverse relationship is tan
Ts 2
Smartworld.asia
For smaller value of frequency
2
Ts
Sin
w
2 =
w
2
Ts
w w3
2 8
w 2
....
w
Ts
Cos 1 ....
2 4
107
The mapping is linear for small and w. For larger freq values, the non linear
compression that occurs in the mapping of to w is more apparent. This compression
causes the transfer function at the high freq to be highly distorted when it is translated to
the w-domain.
Prewarping Procedure:
When the desired magnitude response is piece wise constant over frequency, this
compression can be compensated by introducing a suitable prescaling or prewarping to the
freq scale. scale is converted into * scale.
2 Ts
* = tan
Ts 2
We now derive the rule by which the poles are mapped from the s-plane to the z-plane.
1
Let HA(s) = S=Sp
S Sp
1 Ts(1 Z 1 )
H(z) = =
2 1 Z 1
Sp 2 SpTs1 2 SpTs Z 1
Ts 1 Z 1 2 SpTs
Smartworld.asia
A pole at S=Sp in the s-plane gets mapped into a zero at z= -1 and a pole at Z =
2 SpTs
2 SpTs
Ex:
Chebyshev LPF design using the Bilinear Transformation
Pass band:
-1< H ( j) dB 0 for 0 1404 =4411 rad
Stop band:
H ( j) dB < -60 for 8268 rad/sec =25975 rad/s
2 Ts 4
And s* = tan = 2*10 tan(0.4134 ) = 71690 rad/sec
Ts 2
108
Pass band:
-1< H ( j*) dB 0 for 0 * 4484 rad/s
Stop band:
H ( j*) dB < -60 for * 71690rad/sec
= 0.508
H c js * = 1 2C N2 <10-6
2
p *
s *
Since 16
p *
CN2(16)
10 6 1
<
2
1
10 6 1 2
Smartworld.asia
CN(16) < 2
= 1969
(0.508)
C3(16) = 16301
N = 3 is sufficient
Using Impulse Invariance method a value of N=4 was required.
=4.17
N1 1
N
4484
1
1
4484
1 1
3
r= 4.17 3
4.17 2216
2
2
Since there are three poles, the angles are &
3
S1 = r cos + j Rsin = -2216
2 2
S2,3 = 2216 Cos j 5001 Sin = -1108 j 4331 = 4470 e j104.4
3 3
109
4.43 *1010
Hc(s) =
( s 2216)( S 2 2223s 4470 2 )
Pole Mapping
At S=S1
2 (2216 *10 4 )
In the Z-plane there is zero at Z = -1 and pole at Z = 0.801
2 (2216 *10 4 )
1 Z 1 1 2Z 1 Z 2
H(z) = 4.29 * 10-3
1 0.801Z 1 1 1.638Z 1 0.81Z 2
Pole Mapping Rules:
Hz(z) = 1-CZ-1 zero at Z=C and pole at Z = 0
1
Hp(z) = pole ar Z=d and zero at z=0
1 dZ 1
C and d can be complex-valued number.
Smartworld.asia
Pole Mapping for Low-Pass to Low Pass Filters
Applying low pass to low pass transformation to Hz(z) we get
c 1
1 Z
Z
1
1 c
HLZ(Z) = 1-c = (1+c )
1 Z 1 1 Z 1
c
The low pass zero at z=c is transformed into a zero at z=C1 where C1 =
1 c
And pole at z=0 is Z=
Similarly,
1 Z 1
HLP(Z)=
1 d 1 d Z 1
1 d
d
Pole at z=d => Z=
1 d
Zero at z=0 => z =
1 Z 1 2Z 2Z
1 1 2
H(z) = K
1 0.622Z 1 1.07Z 0.674Z
1 1 2
110
K=
1 (1)(0.356)3 0.029
(1 0.801* 0.356)(1 (0.819 j 0.373)(0.356))(1 (0.819 j 0.373)(0.356))
Smartworld.asia
111
UNIT-VI
( )
Phase Delay: p
d ()
Group Delay: g
d
If p = g =constant and independent of frequency are called as constant time delay or
linear phase filters.
() o
o
p Changes with frequency
g = - =constant.
Type 1 Sequence
Smartworld.asia
N 1
Center of Symmetry M= integer value
2
N 3
jnT
2
N 1
T
2
Amplitude spectrum is even symmetric about w=0 & & both H(0) & H( ) can be non
zero.
Type 2 Sequence
112
h(n) = h(N-1-n)
N 1
Center of Symmetry M= half-integer value
2
N2 1
jMT
H(w) = 2 h(n)CosT (n m) e
n 0
The Amplitude spectrum is even symmetric about w=0 & odd symmetric about w= &
both H( ) is always zero for type 1 & 2 : Constant phase delay and group delay.
Type 3 Sequence
Smartworld.asia
N 1
M= integer value
2
N23
2 h(n) SinT ( M n) e jMT
H(w) = j
n 0
113
It shows generalized linear phase of MT and constant group delay of M. The
2
Amplitude spectrum is odd symmetric about w=0 & w= and H(0) & H( ) are always zero.
(Generalized means () may jump of at 0 if H(ejw) is imaginary.
Type 4 Sequence
N2 1
2 h(n) SinT ( M n) e jMT
H(w) = j
Smartworld.asia
n 0
Generalized linear phase and constant group delay of M. The Amplitude spectrum is odd
symmetric about w=0 & even symmetric about w= and H(0)=0 always.
For N=even, even Symmetry h(n) = h(N-1-n)
N 1
) = h ( n )e
jnT
jT
H( e
n 0
N
1 N 1
+
2
= h( n)e
jnT jnT
h( n)e
n 0 N
n
2
Let N-1-n = m
N
1
2 0
= h( n)e jnT
+ h ( N 1 m) e jT ( N 1 m )
n 0 m
N
1
2
114
N N
1 1
2 2
== h( n)e
n 0
jnT
+ h ( m) e
m 0
jT ( N 1 m )
N
1 N 1 N
1
2 jT N 1
h ( n )e jnT 2 jT
+ h ( m) e
2 jT ( N 1 n ) 2
= e e
n 0 n 0
N
1 N 1 j ( nT 2T ( N 1) j ( T ( N 1 n )
T
( N 1)
2 jT
e e 2
= 2 h ( n )e
n 0
2
2
N
1 N 1
2 jT N 1
= 2 h ( n )e cos T n
2
n 0 2
N
N 1 1
jT 2 N 1
=e
2
2h(n) cos T n ----Magnitude
2
n 0
N 1
T Linear Phase
2
Smartworld.asia
Poles & Zeros of linear phase sequences:
The poles of any finite-length sequence must lie at z=0. The zeros of linear phase
sequence must occur in conjugate reciprocal pairs. Real zeros at z=1 or z=-1 need not be
paired (they form their own reciprocals), but all other real zeros must be paired with their
reciprocals. Complex zeros on the unit circle must be paired with their conjugate (that form
their reciprocals) and complex zeros anywhere else must occur in conjugate reciprocal
quadruples. To identify the type of sequence from its pole-zero plot, all we need to do is
check for the presence of zeros at z= and count their number. A type-2 seq must have an
odd number of zeros at z=-1, a type-3 seq must have an odd number of zeros at z=-1 and
z=1, and type-4 seq must have an odd number of zeros at z=1. The no. of other zeros if
present (at z=1 for type=1 and type-2 or z=-1 for type-1 or type-4) must be even.
115
Smartworld.asia
FIR Filters
Fs Fs
Fourier series Method F
2 2
2Fs 2Fs
2F
2 2
s s
2 2
1. Frequency response of a discrete-time filter is a periodi function with period s
(sampling freq).
2. From the F.S analysis we know that any periodic function can be expressed as a linear
combination of complex exponentials.
Therefore desired freqency response of a discrete time filter can be represented by F.S as
116
H (e jT
) h( n)e
n
jnT
T = sampling period
The F.S co-efficient or impulse response samples of filter can be obtained using
1 s / 2
h (n) =
s s / 2
H (e jT )e jnT d
clearly if we wish to realize this filter with impulse response h(n), then it must have finite
no. of co-efficient, which is equivalent to truncating the infinite expansion of H (e jT ) , which
leads to approximation of H (e jT ) , which is denoted by
m
H 1 (e jT
) h (
n m
n ) e jnT
.
N 1
We choose M= , in order to keep ‘N’ no of samples in h(n).
2
M
h( n) Z n
Smartworld.asia
H1(z) =
n M
However, this filter can’t be physically realizable due to the presence of +ve powers of Z,
means that the filter must produce an output that is advanced in time with respect to the i/p.
N 1
this difficulty can be overcome by introducing a delay M= samples.
2
M
Therefore -M
H(z) = Z H1(z) = Z -M
h( n) Z
n M
n
H(z) = b Z
i 0
i
i
be the transfer function of discrete filter that is physically realizable.
Properties:
1. N=2M+1, impulse response co-eff, bi = 0 to 2M.
2. h(n) is symmetric about bM
Ex: M=4
117
H (e jT ) H1 (e jT )
This implies that magnitude response of the filter we have desired approximates the
desire magnitude response. The time delay of H(ejw) is a constant M. thus sinusoids of
different frequencies are delayed by the same amount as they are processed by the filter, we
Smartworld.asia
have designed. Consequently, this is a linear phase filter, which means that it does not
introduce phase distortion.
Ex:
Design a LPF (FIR) filter with frequency response
H (e jT ) 1 for c
s
= 0 for c
2
1 c jnT
s c
h(n) = e d
2 c
s 0
= Cos (nT )d
2 SincnT
=
s nT
118
2 1
SincnT SincnT
= 1 n
2Fsn.
Fs
bi = h(i-M)
2M
H(z) =
i
bZ i
i 0
Smartworld.asia
s 2Fs 1
w= T T
2 2 Fs
Ex:
Design LPF that approximate following freq response.
H(F) = 1 0 F 1000Hz
=0 else where 1000 F Fs/2
When the sampling frequency is 8000 SPS. The impulse response duration is to be
limited to 2.5ms
Ti = 2MT
2.5 *10 3
M= 10 N=21
1
2*
800
119
1 c jnT
s c
h(n) = 1.e d
1 Fc j 2FnT 1 Fc j 2FnT 2 Fc
2Fs Fc Fs Fc Fs 0
= 1.e 2dF = e dF Cos(2FnT )dF
1 1
= Sin 2FcnT Sin (0.25n )
n n
________________________________________________________________
OR
1
w = T = 2 *1000 *
8000 4
Hc(w) = 1 w
4
= 0 else where
1
2
1.e
4
4
jwn
Smartworld.asia
dw = 1 Sin (0.25n )
n
h(0) = 0.25 h(6) = -0.05305
h(1) = 0.22508 h(7) = -0.03215
h(2) = 0.15915 h(8) = 0
h(3) = 0.07503 h(9) = 0.02501
h(4) = 0 h(10) = 0.03183
h(5) = -0.04502
bi = h(i-10)
20
H(z) = b Z
i 0
i
i
FIR HPF
1 c
1.e jnT d e jnT d
s / 2
h(n) =
s s / 2 c
120
1 e jnT c e jnT s / 2
s jnT
= s / 2 c
jnT
jcnT s
j nT
s
j nT
1 e e 2
e 2 e jcnT
= s jnT
jcnT jcnT
s
j nT j nT
s
2 1 e e e 2
e 2
= s nT
2j 2j
2 s nT
=
2FsnT Sin c nT Sin 2
=
1
n
Smartworld.asia
sin c nT Sinn =
1
n
sin c nT
FIR BPF
2 u 1
sin u nT sin l nT
s l
h(n) = cos nT d =
n
Ex:
Desing a BPF for H(f) = 1 160 F 200Hz
=0 else where
Fs = 800SPS
Ti = 20 ms
Ti 20 *10 3
M= 8 N = 17
2T 1
2*
800
121
H(z) = b Z
i 0
i
i
Smartworld.asia
The abrupt truncation of infinite series is equivalent to multiplying it with the rectangular
sequence.
WR(n) = 1 n M
=0 else where
h (n) h(n)WR (n)
H (e jw ) H (e jw ) *WR (e jw )
1
H (e
j
= )WR (e j ( w ) )d
2
122
Smartworld.asia
4
Main lobe width = & it can be reduced by increasing N, but area of side lobe will
N
be constant.
For larger value of N, transition region can be reduced, but we will find overshoots &
undershoots on pass band and non zero response in stop band because of larger side lobes.
So there overshoots and leakage will not change significantly when rectangular window is
used. This result is known as Gibbs Phenomenon.
The desined window chts are
1. Small width of main lobe of the fre response of the window containing as much as of
the total energy as possible.
2. Side lobes of the frequency response that decrease in energy as w tends to .
3. even function about n=0
N 1
4. zero in the range n
2
123
Let us consider the effect of tapering the rectangular window sequence linearly from the
middle to the ends.
Triangular Window:
2n N 1
WT (n) 1 n
N 1 2
=0 else where
In this side lobe level is smaller that that of rectangular window, being reduced from -13
8
to -25dB to the maximum. However, the main lobe width is now . There is trade off
N
between main lobe width and side levels.
General raised cosine window is
2n N 1
W(n) = (1 )Cos for n
N 1 2
=0 else where
If =0.5 Hanning Window
If =0.54
Smartworld.asia
Hamming Window
2n 4n
WB(n) = 0.42 + 0.5 Cos 0.08Cos Blackman Window
N 1 N 1
Kaiser Window
2n
2
Io 1
N 1
Wk (n) for n
N 1
Io( ) 2
=0 else where
is constant that specifies a freq response trade off between the peak height of the side
lobe ripples and the width or energy of main lobe and Io(x) is the zeroth order modified
Bessel function of the first kind. Io(x) can be computed from its power series expansion
given by
2
1 x k
Io(x) = 1+ k! 2
k 1
124
=1+
(1!) 2 + (2 !) 2 + (3 !) 2 +…..
Smartworld.asia
Kaiser variable variable -
If we let K1,W1 and K2,W2 represent cutoff (pass band) * stop band requirements for the
digital filter, we can use the following steps in design procedure.
1. Select the window type from table to be the one highest up one list such that the stop
band gain exceeds K2.
2. Select no. of points in the windows function to satisfy the transition width for the type
2
of window used. If Wt is the transition width, we must have Wt = W2-W1 k .
N
where K depends on type of window used.
K=1 for rectangular , k=2 triangular…..
2
Therefore N K
w2 w1
125
=0 else where
N = 2M+1 = 21
WH(0) = 1 WH(6) = 0.39785
WH(1) = 0.97749 WH(7) = 0.26962
WH(2) = 0.91215 WH(8) = 0.16785
WH(3) = 0.81038 WH(9) = 0.10251
WH(4) = 0.68215 WH(10) = 0.08
WH(5) = 0.54
Next these window sequence values are multipled with coefficients h(n), obtained in ex1,
Smartworld.asia
to ontain modified F.S Co eff h’(n).
h’(0) =0.25
h’(1) =0.22
h’(2) =0.14517
h’(3) =0.0608
h’(4) =0
h’(5) =0.02431
h’(6) =0.02111
h’(7) =-0.0086725
h’(8) =0
h’(9) =0.00256
h’(10) =0.00255
126
2M
H’(z) = b' Z
i 0
i
i
Ex:
Find a suitable window and calculate the required order the filter to design a LP digital
filter to be used A/D-H(Z)-D/A structure that will have a -3dB cutoff of at 30 rad/sec and
an attenuation of 50dB at 45 rad/sec. the system will use a sampling rate of 100 samples
/sec
Sol:
Smartworld.asia
The desired equivalent digital specifications are obtained as
1
Digital ….. w1 wc cT 30 0.3 k1 3dB
100
1
w2 2T 45 0.45 k 2 50dB
100
1. to obtain a stop band attenuation of -50dB or more a Hamming window is shosen
since it has the smallest transition band.
2. the approximate no. of points needed to satisfy the transition band requirement (or the
order of the filter ) can be found for w1 =0.3 rad &w2 = 0.45 rad, using Hamming
window (k=2), to be
2 2.2
N k =26.65
w2 w1 0.45 0.3
N = 27 is selected
127
the attractive property of the Kaiser window is that the side lobe level and main lobe
width can be varied continuously by simple varying the parameter . Also as in other
window, the main lobe width can be adjusted by varying N.
we can find out the order of Kaiser window, N and the Kaiser parameters to design
FIR filter with a pass band ripple equal to or less that Ap, a minimum stop band attenuation
equal to or greater than As, and a transition width Wt, using the following steps:
Step 1 :
10 0.05 Ap 1
s 10 0.05 As
, p 0.05 Ap
10 1
1 p 1 p
Ap = 20 log 10 As = 20 log 10 => As = 20 log s
1 p s
1
100.05Ap =
1
1 100.05Ap = 1
Therefore: solving above eq for , we get
10 0.05Ap - 1 Smartworld.asia
10 0.05Ap 1
Step 2:
Calculate As using the shosen values
Aso= 20 log
128
Step 3:
Calculate the parameter as follows for
=0 for Aso 21 dB
Smartworld.asia
= 0.5842(Aso -21)0.4 + 0.07886(Aso -21)
= 0.1102(Aso -8.7)
for 21< Aso 50 dB
for Aso >50 dB
Step 4:
Calculate D as follows
D = 0.9222 for Aso 21 dB
As 7.95
= for Aso >21 dB
14.36
Step 5:
Select the lowest odd value of N satisfying the inequality
samD
N 1
t
Wsam : Angular Sampling frequency
sam : Analog Freq
t = s- p for LPF
= p- s for HPF
129
c =
1
p s for LPF & HPF
2
t t
c1 = p1 ; c2 p2 for BPF
2 2
t t
c1 = p1 ; c2 p2 for BSF
2 2
Ex:
Calculate the Kaiser parameter and the no. of points in Kaiser window to satisfy the
following lowpass specifications.
Pass band ripple in the freq range 0 to 1.5 rad/sec 0.1 dB
Minimum stop band attenuation in 2.5 to 5.0 rad /s 40 dB
Sampling frequency : 10 rad/s
Smartworld.asia
Sol:
The impulse response samples can be calculated using h(n) =
1
sin c nT
n
1
Where c = (1.5 2.5) =2rad/s
2
And the no. of points required in this sequence can be found as follows
Step1:
130
D = 2.566
Step 5:
10(2.566)
N 1 26.66 => N=27
1
2n
2
Io 1
N 1
Wk (n)
Io( )
Io( )
Wk (0) 1
Io( )
2
2
Io 3.9524 1
26
Wk (n) Io(3.94)
10.269
0.9899
=
Io(3.9524) Io(3.9524) 10.3729
Smartworld.asia
131
OBJECTIVE PAPER-1
Match the following: For a real valued sequence, the DTFT follow the properties as
9) Re [H (jw) ] a) Real valued function of w
10) Im[ H(jw) ] b) even function of w
Smartworld.asia
11) F.T [even symmetric sequence] c) Imaginary valued function of w
12) F.T [odd symmetric sequence] d) odd function of w
13) x(n) = {4, 1, 3} h(n) = {2, 5, 0, 4} what is the output of the system.
a) {8, 22, 11, 31, 4, 12} b) {8, 22, 11, 31, 4, 12} c) {8, 22, 11, 31, 4, 12}
d) none
14) y(n) = x(n) * h(n) then y1 (n) = {0, 0, x(n), 0 } * { 0, h(n), 0 } is equal to
a) {0, 0, y(n), 0} b) {0, 0, 0, y(n), 0, 0} c) [0, 0, y(n), 0 } d) {0, y(n), 0, 0}
15)If x(n) and h(n) are having N values each, to obtain linear convolution using circular
convolution, the number of zeros to be appended to each sequence is
a) N – 1 b) 2N – 1 c) N d) N + 1
16)W49 = ?
a) – j b) + j c) + 1 d) -1
132
OBJECTIVE PAPER-2
5) Consider the system shown in fig. The transfer function Y(Z) / X(Z) of the system is
x(n) y(n)
+ +
Z-1
-1
a) (1+aZ )/ ( 1+bZ )
Smartworld.asia
-1
-b
-1
b) (1+bZ )/ ( 1+aZ )
a
-1
6) A linear discrete time system has the characteristic equation Z3-0.8 Z=0, the system
a) is stable b) is marginally stable
c) is un stable d) stability cannot be assessed from the given information
akx(n k )
5
8) y(n) = - k 1
b k(yn k ) the minimum no of delay elements
k 2
needed to realize the system is
a) 5 b) 10 c) 8 d) 11
10) To ensure a causal system, the total no of zeros must be less than or equal to the total
number of poles ( T / F )
133
1 2 3 4 5 6 7 8 9 10
a a c c a a a c T
11) The poles or zeros at the origin do effect the magnitude response ( T / F)
12) All poles and zeros of a minimum phase system lie inside the unit circle ( T / F)
14) Find total no of complex multiplications using FFT for N=8: __________
15) Find total no of complex additions using FFT for N=8: __________
16) Find total no of real additions using direct DFT for N=8: __________
11 12 13 14 15 16
Smartworld.asia
F T a 12 24 240
134
OBJECTIVE PAPER-3
State TRUE or FALSE
1) u(n) = (n k )
K 0
a) 8 b) 16 Smartworld.asia
9) x(n) = Cos 0.125n , what is the period of the sequence
c) 125 / 2 d) none
1 2 3 4 5 6 7 8 9 10 11 12
T F T F 3 1 4 2 B B A a
13) The output of anti causal LTI system is
n
a) y (n) = h( k ) x ( n k )
K 0
b) y (n) = h( k ) x ( n k )
K 0
1
c) y (n) = h( k ) x ( n k )
d) y (n) = h( k ) x ( n k )
135
18) Given g(n) = {1, 2, 3} , find x(n) = g (n / 2), using linear interpolation
19) Smartworld.asia
h1(n) + h3(n) y(n)
x(n)
h2(n)
In the figure shown, how do you replace whole system with single block
a) [ h1(n) + h2(n) ] * h3(n) b) h1(n)h3(n) * h2(n)h3(n)
c) [ h1(n) + h2(n) ] h3(n) d) none
20 The h(n) is periodic with period N, x(n) is non periodic with M samples, the output
y(n) is
a) Periodic with period N b) Periodic with period N+M
c) Periodic with period M d) none
13 14 15 16 17 18 19 20
C A B B C C A A
136
OBJECTIVE PAPER-4
a) 6 b) 10 c) 0 d) none
2) If x(n) = 1, |n|≤2
0, other wise
Find DTFT
a) sin(5w)/sinw b) sin(4w)/sinw c) sin(2.5w)/sin(0.5w) d) none of the above
a) {8, 22, 11, 31, 4, 12} b) {8, 22, 11, 31, 4, 12} c) {8, 22, 11, 31, 4, 12} d)
none
Smartworld.asia
6) y(n) = x(n) * h(n) then y1 (n) = {0, 0, x(n), 0 } * { 0, h(n), 0 } is equal to
a) {0, 0, y(n), 0} b) {0, 0, 0, y(n), 0, 0} c) [0, 0, y(n), 0 } d) {0, y(n), 0, 0}
7) If x(n) and h(n) are having N values each, to obtain linear convolution using circular
convolution, the number of zeros to be appended to each sequence is
a) N – 1 b) 2N – 1 c) N d) N + 1
8)W49 = ?
a) – j b) + j c) + 1 d) -1
9) DFT [ x* (-n) ] = ?
a) X * (K) b) X * (-K) c) X * (N-K) d) none
11) Both discrete and periodic in one domain are also periodic and discrete in other
domain (T / F)
137
13) Reversing the N point sequence in time is equivalent to reversing the DFT values (T /
F)
OBJECTIVE PAPER-5
a) X( )=
Smartworld.asia
1. The Fourier transform of a finite energy discrete time signal, x(n) is defined as [
x(n) e jn
b) X( )=
x(n) en
]
n=- n=-
x(n) e x(n) e
-jn -jn
c) X( )= d) X() =
n=- n=0
N 1 j 2kn N 1 j 2kn
a) x(n) =
1
N
n 0
X(k) e N b) a) x(n) =
1
N
n 0
X(k) e N
j 2kn N j 2kn
c) x(n) =
1
N
n 0
X(k) e k d) a) x(n) =
1
N
n 0
X(k) e N
3. A N – periodic sequence x(n) and its DFT x(k) are known. Then the DFT of x(n) =
(n) will be
a) e-j2nk b) 1 c) e-j2nok/N d) e-j2nk /N [ ]
4. If the length of sequence x(n) is L and h(n) is M then the length of o/p sequence of the
circular convolution is [ ]
a) L+M b) L+M-1 c) L if L>M d) 2L if L=M
138
7. The circular shift of an N point sequence is equivalent to linear shift of its periodic
extension [ ]
8. The multiplication of DFT of two sequences is equal to DFT of the linear convolution
of two sequences [ ]
_______________ Smartworld.asia
12.The two methods of sectioned convolution are ________________ &
15.To get the result of linear convolution with circular convolution of sequence x(n) &
h(n), the sequences should extended to the length of __________________
e) x1(n) x2*(-n)
139
1= 2= 3= 4=
17. Show that the given sequence x(n) = { 1,-2,3,2,1,0} for the following conditions
using concentric circles.
a) x(-n) b) x(2-n) (2M)
OBJECTIVE PAPER-6
MULTIPLE CHOICES
1. In Impulse invariant transformation, the mapping of analog frequency to the digital
frequency is
a) one to one b) many to one c) one to many d) none
2. The digital frequency in bilinear transformation is
a) w = 2 tan-1(Ts/2) b) w = tan-1(Ts/2)
c) w = 2 tan-1(Ts) d) w = 2 tan-1(/2)
Smartworld.asia
3. Which technique is useful for designing analog LPF
a) Butter worth filter
c) Both a and b
b) Chebyshev filter
d) none
4. Which filter is more stable?
a) Butter worth b) Chebyshev c) none
5. As increases , the magnitude response of LPF approaches with
a) –20Ndb/oct b) –6Ndb/oct c) –10Ndb/dec d) none
6. Using Impulse invariant technique the pole at S= SP is mapped to Z-plane as
a) Z=e-SPTs b) Z=e (SPTs) c) Z=eSP (Ts) d) None
TRUE or FALSE
7. The disadvantage of Chebyeshev filter is less transition region
8. The advantage of Butter worth filter is flat magnitude response.
9. for the given same specifications order of the Chebyshev filter is more than
Butterworth filter
10. Poles of Butterworth filter lies on circle.
1 2 3 4 5 6 7 8 9 10
B A C A B B F T F T
140
17.Given allowable ripples in Pass band is –3 dB, the value of is 0.997 (2M)
OBJECTIVE PAPER-7
Choose the correct Answer
Smartworld.asia
2. The digital frequency in Bi –linear transformation is [ ]
a) = 2 tan ( T /2)
-1
b) = tan ( T /2)
-1
c) = 2 tan ( T )
-1
d) = 2 tan-1( /2)
3. Using bilenear transformation for T = 1sec the pole p k is in S- Plane is mapped to Z –
plane using [ ]
1 z 1 1 z 1 1 z 1 Z 1
a) S = 2 b) S = c) S = 2 d) S=
1 z 1 1 z 1 1 z 1 Z 1
2 1 1
c) H a () = d) H a () =
1 C N ( / c )
2 2
1 C N ( / c )
2
141
10.In …………………. Window spectrum the width of main lobe is double that of
rectangular window for same value of N [ ]
a) Hamming window b) Kaiser window c) Blackman window d) none
Smartworld.asia
13.The advantage of Butter worth filter is flat magnitude response.
[
]
]
in pass band.
15.For same specifications, the order N of chebyshev filter is less compared to Butter
worth filter. [ ]
20.In FIR filter with constant phase delay the impulse response is symmetric
[ ]
142
OBJECTIVE PAPER-8
Smartworld.asia
N N N N
n 0 n 0 K 0 n 0
8. If M & N are the lengths of x(n) & h(n) then length of x(n) * h(n) is [ ]
a) M+ N –1 b) M + N +1 c) max (M,N) d) min (M,N)
11.In a discrete signal x(n), if x(n) =x(-n) then it is called symmetric signal [ ]
12.The F.T of the product of two time domain sequence is equivalent to product
of their F.T [ ]
13.The DFT of a signal can be obtained by sampling one period of FT of the signal
[ ]
14.DFS is same as DTFS [ ]
143
OBJECTIVE PAPER-9
CHOOSE THE CORRECT ANSWER
1. Power signal is
a) Periodic b) aperiodic c) Continuous d) none [ ]
2. WN nK is
j 2 K j 2 Kn 2 Kn
j 2 nK
a) e N
b) e c) e N
d) e N
[ ]
3. When the sequence is circularly shifted in time domain by ‘m’ samples i.e. x((n-m))N
then on applying DFT, it is equivalent multiply sequence in frequency domain by
j 2 Km j 2 Km 2 Km
j 2 Km
a) e N
b) e N
c) e d) e N
[ ]
K 0
Smartworld.asia
5. Linear convolution of two sequences N1 and N2 produces an output sequence of length
a) N1 – N2 +1 b) N1 + N2 –1 c) N1 + N2 +1 d) 2N1 – N2 +1[ ]
10.Appending zeros to a sequence in order to increase the size or length of the sequence
is called ……………………..
11.In N-point DFT using radix 2 FFT, the decimation is performed …………… times.
12.In 8-point DFT by radix 2 FFT, there are …………… stages of computations with
…………………….. butterflies per stage.
144
15.How many multiplications and additions are required to compute N-point DFT using
radix 2 FFT
16.How many multiplications and additions are required to compute N-point DFT
Smartworld.asia
18.What is the expression for N-point IDFT of a sequence X(K) ?
145
OBJECTIVE PAPER-10
1. How we can calculate IDFT using FFT algorithm. (2M)
Smartworld.asia
5. Find the Z-Transform and ROC for the signal x(n) = an u(n).
6. Find the Z-Transform and ROC for the signal x(n) = - an u(-n-1).
8. Z{(n)} = ……………………..
Z
9. Find inverse Z-Transform for X(z) = when ROC is Z<1
Z 1
146
10.What are the differences and similarities between DIT and DIF algorithms. (2M)
Smartworld.asia
13.What is the relationship between Z-Transform and Fourier transform.
17.Direct form I required less no.of memory elements as compared to Canonic form.[ ]
18.A linear time invariant system with a system function H(Z) is BIBO stable if and only
if the ROC for H(Z) contains unit circle. [ ]
147
OBJECTIVE PAPER-11
2. What is the relation between analog and digital radiant frequency in Impulse
Invariance design..
3. What is the relation between analog and digital radiant frequency in Bilinear
transformation design.
Smartworld.asia
4. What are the drawbacks with Impulse Invariance method?
7. Mention any two techniques to design IIR Filter from analog filter.
8. What are the differences between Chebyshev type I and type II.
148
TRUE OR FALSE
12.Poles of Butterworth filter lies on circle. [ ]
Smartworld.asia
14.Transition bandwidth for Chebyshev is more as compared to Butterworth filter.[
15.Butterworth filters are all pole filters. [
]
]
17.Chebyshev, type II filter exhibit equiripple behavior in the pass band and monotonic
characteristic in the stopband. [ ]
18.Chebyshev, type I filter exhibit equiripple behavior in the pass band and monotonic
characteristic in the stopband. [ ]
20.For the given specifications order of the Chebyshev filter is more as compared to
Butterworth filter. [ ]
149
OBJECTIVE PAPER-12
c. Dynamic system
d. Recursive System
2.
Smartworld.asia
Give the example for FIR and IIR systems.
150
8. Find the Convolution Sum Graphically with all the steps-------3 Marks
x(n)= 2 1 h(n)= 1 1
-1 0 0 1
9.
Smartworld.asia
Write the properties of Convolution Sum --------2 Marks
11. Write the necessary condition for the stability of the system
151
OBJECTIVE PAPER-13
State TRUE or FALSE
1. In direct –form II realization the number of memory locations required is more than
that of direct form –I realization [ ]
2. An LTI system having system function H(z) is stable if and only if all poles of H(z)
are out side the unit circle. [ ]
5. As the order of Butter worth filter increases than the response is closer to ideal filter
response. [ ]
Answer the following
Smartworld.asia
7. Indicate the poles and zeros of the given system and also check the stability of the
system
z ( z 1)
H(z) = (2M)
( z 0.2)( z 0.4)( z 0.5)
8. Realize the given system function H(z) using direct form –II
3 3.6 z 1 0.6 z 2
H(z) = (2M)
1 0.1z 1 0.2 z 2
152
9. Realize the given system function H(z) using cascade form (2M)
1
H(z) =
(1 0.5 z )(1 0.5 z 1 )
1
z
10.Find the inverse z-transform of x(z) = using partial fraction method.
( z 2)( z 3)
(2M)
Smartworld.asia
12.Mention the two conditions to realize any digital filter
14.The order of the Butter Worth filter is obtained by using the formula N
______________________
153
OBJECTIVE PAPER-14
3. The number of multiplications needed in the calculation of DFT using FFT with 32-
point sequence = ________________
6. For DIT –FFT algorithm the input is bit reversed and the output is in natural order
[ ]
8. WNNK 1
9. W NK
1
Smartworld.asia [
[
]
]
N /2
10.In DIT –FFT, the input sequence is divided into smaller subsequences [ ]
11.Calculate the DFT of the sequence x(n)={1,0,0,1} using DIT –FFT (2M)
12.Draw the Butterfly diagram for 8-point DFT using DIT –FFT algorithm (2M)
154
14. Write the steps for the calculation of IDFT using DIT –FFT (2M)
Smartworld.asia
a) Dynamic b) Static c) time variant d) None
155
11. The average power of a discrete time signal with period N is given by ___________
12. The convolution sum of causal system with causal sequence is ____________
Smartworld.asia
14. x(n) = {3, -2, 1,0,-1} show for x(-n) (1M)
156
17. If the impulse response h(n) = 2n u( -n) then determine the corresponding system is
causal or stable. (1M)
18. Test the given discrete system for linearity , causality and time invariance
h(n) = n ex(n) ( 2M)
ASSIGNMENT UNIT-5
1 (a) Draw the frequency response of N-point rectangular window.
(b) Design a fifth order band pass linear phase filter for the following specifications.
i. Lower cut-off frequency = 0.4 πrad/sec
ii. Upper cut-off frequency = 0.6 πrad/sec
iii. Window type = Hamming
Draw the filter structure. [4+12]
2) Design a band pass filter to pass frequencies in the range 1-2 radians/second using
Hanning window N=5. Draw the filter structure and plot its spectrum. [16]
3) (a) Compare the performances of rectangular window, hamming window and Keiser
window
Smartworld.asia
(b) The desired response of a low pass filter is
Hd(ej!) = _ e−j3!, −3π _ ω _ 3π/4
0 , 3π/4 _ |ω| _ π
Determine H(ej!) for M=7 using a Hamming window. [6+10]
4) (a) Design a linear phase low pass filter with a cut-off frequency of π/2
radians/seconds. Take N=7
(b) Derive the magnitude and phase functions of Finite Impulse Response filter when
i. impulse response is symmetric & N is odd
ii. impulse response is symmetric & N is even. [8+8]
5) (a) Design a low pass filter by the Fourier series method for a seven stage with cut-off
frequency at 300 Hz if ts = 1msec. Use hanning window.
(b) Explain in detail, the linear phase response and frequency response properties of
Finite Impulse Response filters. [8+8]
6) (a) Outline the steps involved in the design of FIR filter using windows.
(b) Determine the frequency response of FIR filter defined by y(n) = 0.25x(n)+ x(n-1)+
0.25x(n-2). Calculate the phase delay and group delay. [8+8]
7) (a) Define Infinite Impulse Response & Finite Impulse Response filters and com-pare.
157
(b) Design a low pass Finite Impulse Response filter with a rectangular window for a
five stage filter given: Sampling time 1 msec; fc = 200Hz.Draw the filter structure with
minimum number of multipliers. [6+10]
ASSIGNMENT UNIT-7
1) a) What are the advantages of Multirate signal processing?
b) Differentiate between Decimator and Interpolator?
2) Prove that spectrum of down sampler is sum of M uniformly shifted and stretched
version of X(ejw) scaled by a factor 1/M and also discuss the aliasing effect?
3) State and prove any one identity property in down sampler and any one identity
property in up sampler?
4) Let x(n)={1,3,2,5,-1,-2,2,3,2,1},find
a) Up sample by 2 times and down sample by 4 times
b) Down sample by 4 times and up sample by 2 times c) Justify why these outputs are
not equal.
Smartworld.asia
158