Beruflich Dokumente
Kultur Dokumente
Chassis : LS23CFV
Model : 2333HD
SERVICE Manual
1. Precautions
2. Product specifications
4. Troubleshooting
6. Wiring Diagram
2333HD
Refer to the service manual in the GSPN (see the rear cover) for the more information.
1. Precautions
1-1. Safety Precautions
Follow these safety, servicing and ESD precautions to prevent damage and to protect against potential hazards such as
electrical shock.
1-1-1. Warnings
1. For continued safety, do not attempt to modify the circuit board.
2. Disconnect the AC power and DC power jack before servicing.
LEAKAGE
DEVICE
CURRENT
UNDER
TESTER
TEST
TEST ALL
EXPOSED METAL
SURFACES
2-WIRE CORD
1-1
1-2
1-3
Memo
1-4
2. Product specifications
2-1. Feature & Specifications
Feature
Specifications
Item Description
Model 2333HD
LCD Panel TFT-LCD Panel, RGB Vertical stripe, normally White, 23-Inch viewable,
0.2655 (H) X 0.2655 (V) mm Pixel Pitch
Scanning Frequency Horizontal : 30 kHz ~ 81 kHz (Automatic)
Vertical: 56 Hz ~ 75 Hz(Automatic)
Display Colors 16.7 Million colors
Maximum resolution Horizontal: 1920pixels
Vertical: 1080pixels
Input Signal Analog 0.7 Vp-p ±5% positive at 75Ω, internally terminated
Input Sync Signal Type : Seperate H/V
Level : TTL level
Maximum Pixel Clock rate 138.5 MHz
Active Display
509.76 (H) X 286.74 (V)
(Horizontal/Vertical)
AC power voltage & Frequency AC 110 ~ 240V, 50 ~ 60 Hz
Power Consumption 58W⾘2W
Dimensions Set 557.8 X 363.8 X 74.0 (Without Stand)
(W x D x H) 557.8 X 415.3 X 218.8 (With Stand)
Weight Set
6.1 Kg
(After installation Stand)
TV System Tuning Frequency Synthesize
System PAL, NT443, SECAM
Sound MONO, STEREO, NICAM
2-1
Specifications
Item Description
Model 2333HD
Environmental Considerations Operating Temperature: 50˚C ~ 104˚F(10˚C ~ 40˚C)
Operating Humidity : 10% ~ 80%
Storage Temperature: -4˚C ~ 113˚C(-20˚C ~ 45˚C)
Storage Humidity: 5% ~ 95%
Antenna Input 75Ω
Sound Characteristic -MAX Internal speaker Out : Right : 3W / Left : 3W
-BASS Control Range : -8 dB ~ + 8dB
-TREBLE Control Range : -8 dB ~ +8 dB
-Headphone Out : 10 mW MAX
-Output Frequency : RF : 80 Hz ~ 15 kHz
A/V : 80 Hz ~ 20 kHz
2-2
Design
Sound Output 3W x 2 3W x 2
UI Single UI Smart UI
Image Size : If the resolution is not wide resolution, this option allows the screen size to be selected as normal or wide.
2-3
2-3. Accessories
Product Description Ccde. No Remark
Remote Control
& BN59-00865A
Batteries (AAA x 2)
Samsung Electronics
Service center
Stand Base BN96-07604A
User’s Guide,
Monitor Driver, BN59-00905A
Natural Color Pro Software
2-4
3-1. Disassembly
Caution: 1. Turn the monitor off before beginning the disassembly process.
2. When disassembling the monitor, do not use any metal tools except for the provided jig.
3. Remove the signal cable and the power cord before beginning the disassembly.
ZTX
ZTYG
ZTZ
ZT[G
4. Troubleshooting
4-1. First Checklist for Troubleshooting
1. Check the various cable connections first.
- Check to see if there is a burnt or damaged cable.
- Check to see if there is a disconnected cable connection or a connection is too loose.
- Check to see if the cables are connected according to the connection diagram.
2. Check the power input to the Main Board.
3. Check the following circuits.
• No raster appears: Function PBA, Main PBA, I/P PBA
• 55V develop but no screen: Main PBA
• 5V does not develop: I/P PBA
4. Check the voltage in and out between the IP↔ Main Board, between the IP↔ Panel, and between the Main LVDS
Boards.
4-1
4-2. No Power
Symptom - Though the power swtich on, the LED power off and the screen is blank.
C1070
BD1014
IC1004
IC1010
C1105
Caution Make sure to disconnect the power before working on the IP board.
4-2
4-3
- Even though the LED power turns on, the screen is blank when connecting the VGA cable.
Major - Check the D-sub cable connections.
checkpoints - Check whether the LVDS cable is connected correctly to the panel.
- Check whether the lamp connector of the panel is connected correctly to the IP board.
IC4010
RA4000,RA4001
R802
R803
R807
Caution Make sure to disconnect the power before working on the IP board.
4-4
4-5
4-6
- Even though the LED power turns on, the screen is blank when connecting the DVI cable or
HDMI cable.
Major - Check the DVI cable or HDMI cable connections.
checkpoints
- Check whether the LVDS cable is connected correctly to the panel.
- Check whether the lamp connector of the panel is connected correctly to the IP board.
IC4010
RA4002 D6008,D6010
RA4003
RA4004,RA4005
D6005,D6007
Caution Make sure to disconnect the power before working on the IP board.
4-7
4-8
4-9
- Even though the LED power turns on, the screen is blank when connecting the RF cable.
Major - Check the RF cable connections.
checkpoints - Check whether the LVDS cable is connected correctly to the panel.
- Check whether the lamp connector of the panel is connected correctly to the IP board.
IC4010
TU5003
RA4002
RA4003
RA4004,RA4005
R5899
Yes
Caution Make sure to disconnect the power before working on the IP board.
4-10
4-11
4-12
- Even though the LED power turns on, the screen is blank when connecting the Antenna Cable.
Major - Check the Antenna Cable connections.
checkpoints - Check whether the LVDS cable is connected correctly to the panel.
- Check whether the lamp connector of the panel is connected correctly to the IP board.
IC4010
TU5003
Caution Make sure to disconnect the power before working on the IP board.
4-13
4-14
4-15
4-7. No Sound
Symptom - The LED power turns on but the screen is blank when the DVI cable is connected.
- Even though the LED power turns on, the screen is blank when connecting the DVI cable.
Major - Check the DVI cable connections.
checkpoints - Check whether the LVDS cable is connected correctly to the panel.
- Check whether the lamp connector of the panel is connected correctly to the IP board.
IC4010
IC9003
IC9002
No check IC9003.
Check the 3.3V of #1 IC9002.
Change a main PBA.
Yes
Caution Make sure to disconnect the power before working on the IP board.
4-16
4-17
4-18
Symptoms: When the monitor is turned on, * A full white pattern is a feature of the
only a full white pattern is displayed TN panel and is displayed when no
continually regardless of the signals. video signals are supplied.
4-19
4-9. Adjustment
4-9-1. Service Instruction
1. Usually, a color TV-VCR needs only slight touch-up adjustment upon installation.
Check the basic characteristics such as height, horizontal and vertical sync.
2. Use the specified test equipment or its equivalent.
3. Correct impedance matching is essential.
4. Avoid overload. Excessive signal from a sweep generator might overload the front-end
of the TV. When inserting signal markers, do not allow the marker generator to distort test result.
5. Connect the TV only to an AC power source with voltage and frequency as specified on the backcover nameplate.
6. Do not attempt to connect or disconnect any wire while the TV is turned on. Make sure that the power cord is
disconnected before replacing any parts.
7. To protect aganist shock hazard, use an isolation transform.
4-20
(Gray patten)
*Color temperature
1500K +/-500, -6 ~-20 MPCD
*Color coordinate
H/L : 267/263 +/- 2 35.0 Ft +/- 2.0Ft
L/L : 270/260 +/- 3 1.5 Ft +/- 0.2Ft
Toshiba Patten
4-21
Low light
Measurement point
Low light
Measurement point
4-22
1
4
- Run winDDC
4-23
2. Run winDDC
4-24
9
7
10
4-25
11
12
13
4-26
7
6
4-27
10
4-28
M0027
M0013
M0028
T0279
M0006
BN63-05080A
M0215
T0003
M0174
T0175
5-1
5-2
Level Location No. Code No. Description & Specification Q’ty SA/SNA Remark
5-3
Level Location No. Code No. Description & Specification Q’ty SA/SNA Remark
5-4
Level Location No. Code No. Description & Specification Q’ty SA/SNA Remark
5-5
Level Location No. Code No. Description & Specification Q’ty SA/SNA Remark
5-6
Level Location No. Code No. Description & Specification Q’ty SA/SNA Remark
5-7
Level Location No. Code No. Description & Specification Q’ty SA/SNA Remark
5-8
Level Location No. Code No. Description & Specification Q’ty SA/SNA Remark
5-9
5.1V
5.1V
CN9001
GND
GND
GND
PWM
NC GND
ON/OFF
SCL GND
A-Diming
CN1001
SDA GND
NC GND
CN3000
RX1- DDC5V
RX1+ VSYNC
GND GND
NC SDA
NC H SYNC
DDC5V V SYNC
Check HDMI SCL
HDCP
RX0-
RX0+
GND
NC Vcc
NC Vcc
NC Vcc
RXC+ NC
CN5002
RXC- NC
NC
GND
LVA3P
RX2+ GND LVA3M
GND SR LVACKP
RX2- SL LVACKM
RX1+ SL
JA3003
LVA2P
CN3001
GND SL LVA2M
RX1- SR GND
RX0+ SR LVA1P
SR GND LVA1M
SR RX0- GND
SL RXC+ LVA0P
SL SPDIF
GND LVA0M
CN2001
Vcc
RXC- LVB3P
GND
OP401
NC LVB3M
NC LVBCKP
SCL LVBCKM
SDA GND
GND GND
LVB2P
DDC5V RX
LVB2M
Hotplug TX
LVB1P
TX
LVB1M
TX
JA3005
LVB0P
RX
LVB0M
RX
SR_0
GND
SR_I
SR
SR_0
SL
GND
JA4001
GND
CN4001
GND
SL
SL_I
SR
B
GND SC_ID
GND GND
NC NC
LED G
CN9002
IR NC
KEY1 GND
Y GND
KEY2 GND
VCC Y
GND R
B FB
CN4002
B GND
GND GND
R CVBS_O
R CVBS_I
GND
1
2
3
11
10
SL
SL
SR
SR
NC
NC
SCL
SDA
GND
GND
GND
GND
GND
GND
RX0-
RX1-
RX2-
RXC-
RX0+
RX1+
RX2+
RXC+
DDC5V
CN3004
CN2003
6-1. Wiring Diagram - Main Board
6. Wiring Diagram
6. Wiring Diagram
6. Wiring Diagram
LVDS Connector
(Connect to Panel)
IP board
3708-001150
3711-005503
3701-001388
3701-001385
3701-001367 3722-000143
3701-001386 3722-002360
3722-002362
6-2
Power
Lamp Connector Connector 9P
(Connect with panel (Connect with
inverter – left top of MAIN board)
panel rear)
Lamp Connector
(Connect with panel
inverter – left bottom
of panel rear)
AC Power socket
6-3
CN5002 Transmits LVDS signals from the Main board to the panel
* When a problem occurs: The Blank Screen and No Power errors may occur.
CN1001 Supplies 5V and 13V from the Power board to the Main board. Receives and transmits the
PWM output to the Inverter.
* When a problem occurs: The Blank Screen and No Power errors may occur.
6-5. Cables
Use LVDS 30P FFC cable
Code BN96-08740B
Photo
6-4