Beruflich Dokumente
Kultur Dokumente
SIX-PEN
DRILLING RECORDER
(English, Metric and SI)
PAGE ISSUE
NUMBER DATE
A
INSTRUCTION MANUAL 26-81
INSTRUCTION MANUAL 26-81
TABLE OF CONTENTS
Section Page
LIST OF ILLUSTRATIONS
Figure Paee
ii
INSTRUCTION MANUAL 26-61
LIST OF ILLUSTRATIONS (CONT’D)
Figure Page
2-16 Electric Torque Unit. ..................... 2-45
2-17 Electric Torque Shunt Box Assembly. .............. 2-48
2-18 Explosion-Proof Shunt Box Assembly. .............. 2-50
2-19 Remote Control Air Valve and Bracket Assembly ......... 2-52
2-20 Recorder Unit ......................... 2-54
2-21 Mainspring Housing Assembly .................. 2-60
2-22 Measuring Cable Drum Assembly ................. 2-61
2-23 Sheave Support Assembly .................... 2-62
2-24 Derrick Pulley Assembly .................... 2-63
2-25 Air Motor Housing Assembly. .................. 2-64
2-26 Air Motor Regulator-Oiler Assembly. .............. 2-66
2-27 Air Motor Oiler Assembly. ................... 2-68
2-28 Air Motor Regulator Assembly. ................. 2-70
2-29 Recorder Assembly ....................... 2-72
2-30 Chart Drive Assembly. ..................... 2-80
2-31 Chart Drum Assembly ...................... 2-82
2-32 Housing Cover Assembly. .................... 2-84
2-33 Penetration Counter Assembly. ................. 2-86
2-34 Weight Pen Arm Assembly .................... 2-89
2-35 Penetration Pen Arm Assembly. ................. 2-90
2-36 Pen Arm Retractor Assembly. .................. 2-91
2-37 Index, Cam Shaft, and Trigger Assemblies. ........... 2-92
2-38 Penetration Driveshaft Assembly ................ 2-94
2-39 Multiple Pen Arm Bracket Assembly ............... 2-96
2-40 Air Cylinder Assembly ..................... 2-98
2-41 Recorder Housing Assembly ................... 2-100
LIST OF TABLES
Table Page
iii
INSTRUCTION MANUAL 26-81
RELATED PUBLICATIONS
iv
INSTRUCTION MANUAL 26-81
SECTION I
INTRODUCTION
l-l
.-_ INTRODUCTION
l-2 This manual contains an illustrated parts breakdown for the Six-Pen Drilling
Recorder manufactured by TOTCO Drilling Instrumentation.
l-3 This section describes how to use the GROUP ASSEMBLY PARTS LIST, NUMERICAL
INDEX (when included), and other related information.
l-5 The GROUP ASSEMBLY PARTS LIST section (See Figures 2-1 and subsequent) in-
cludes detailed or exploded views accompanied by parts lists keyed to the
index numbers on the illustrations. Index numbers on the illustration are circled
if the component or subassembly is broken down by a subsequent detail illustration
and parts list. Each assembly is listed in its disassembly order. Part descrip-
tions show a relationship to an assembly by indentation. The relationship of a
part to the next higher assembly (NHA) or main group may also be shown by cross-
reference notes. Attaching parts immediately follow the items they attach and
are identified by (AP) following the description. Attaching parts indent to the
same level as the items attached.
1-6 FIGURE AND INDEX NUMBER COLUMN. Three groups of digits separated by dashes
make up this column (i.e. X-X-XX). The first two groups represent the
figure number of the corresponding illustration. The last group of digits is the
index number of each part found in the illustration. An asterisk (") instead of
an index number indicates the part is not illustrated.
l-7 PART NUMBER COLUMN. This column lists TOTCO part numbers and standard
items. The entry STD HDW in this column identifies hardware without an
assigned part number and indicates availability from commercial sources. Infor-
mation for purchase of these items is contained in the DESCRIPTION column.
l-8 DESCRIPTION COLUMN. This column describes each assembly, its attaching
parts, and detail parts of the assembly. Indentation shows relationship
of parts to the assembly. Parts identified with (AP) are attaching parts for
items and assemblies. Where it is impractical to show completely in one illustra-
tion all detail parts of any one subassembly, the subassembly is illustrated
completely assembled as part of one illustration and a separate, disassembled
view of the subassembly is furnished. A notation in parentheses following a
description cross-refers a subassembly to its illustration or refers to the figure
and index number of the subassembly on the NHA illustration.
l-9 Listed parts are indented to indicate item relationship to the NHA. The
description of each assembly is followed in the list (except for attaching
parts) by its detail parts indented one column to the right (See 4, Figure l-l).
To determine the NHA of a part or assembly, note the column in which the first word
of the nomenclature appears. The first item directly above which appears one column
to the left (except for attaching parts) is the NHA.
1-l
INSTRUCTION MANUAL 26-81
”-11.
._..
.-.1-.--
_.
Index
.-I
-rl.
_._
,.-.
..-_..-
_--.
number
accompanying
list are assigned
of a part
parts list.
on the
in disassembly
Index
Part
parts.
number of assemblies and
illustration
numbers
order.
illustrated
An
and /
in parts
detail
I
I
A
-8
. . ...*
16036’
KN”B
CD.I.1F’ :.:.: :.:-I
I
Quantity of parts used in one part or assembly
(or used to attach one part or assembly).
TC” 815~06211)l5/81)
I
SLYT”. hd hd. b. LO-,? r 118. * I
TCO 815452121l5/81~
\‘ 1 Locate
illustration.
the system or top assembly (end item) 4 Locate the required
tion and note the
part.
part
index
on the
number
detail
assigned
illustra-
to the
\
3 Use the associated parts list (the FIGURE
number on the illustration and the parts list
must match) to find the detail illustration that
has a breakdown of the applicable component
or subassembly.
TCO 815-06213~~5/81)
1-4
INSTRUCTION MANUAL 26-81
l-10 UNITS PER ASSEMBLY COLUMN. This column lists the number of units required
for one NHA. Therefore, the quantities specified are not necessarily the
total number used per installation or end item. AR denotes that parts should be
selected as required. The term REF denotes parts which are listed for reference
purposes. Units per assembly for other REF items are shown on the appropriate
figures referenced in the DESCRIPTION column. NP denotes parts not procurable.
l-11 USE ON CODE COLUMN. Code letters in this column show variations in parts
on two or more similar assemblies. Parts peculiar to a particular assembly
are identified by the same code letter as the main assembly; common parts are un-
coded.
1-13 The NUMERICAL INDEX section contains a numerical listing of parts and/or
drawings that are listed in the GKOUP ASSEMBLY PARTS LIST. Standard
hardware items are not included.
1-15 Additional informative lists, such as a SPARE PARTS LIST and FUSE LIST,
follow the GROUP ASSEMBLY PARTS LIST section or NUMERICAL INDEX section
(as applicable).
1-16
____----___-.HOW TO USE THE ILLUSTRATED PARTS BREAKDOWN
1-17 If the part number of an item is known, turn to the NUMERICAL INDEX and
find the applicable figure and index number. Use the figure and index
number to locate the illustration and description of the part in the GROUP ASSEMBLY
PARTS LIST.
l-18 If the part number of an item is unknown, turn to the system or top assembly
illustration (usually the first illustration in the GROUP ASSEMBLY PARTS
LIST). Trace back through the applicable component or subassembly detail illustra-
tions to locate the one in which the required item appears and is identified with
an index number. When the correct illustration has been located, use the FIGURE
number of that illustration to find the corresponding parts list. Use the index
number of the required item (assigned in the corresponding illustration) to locate
the item in the parts list.
1-5
INSTRUCTION MANUAL 26-61
SECTION. II
GROUP ASSEMBLY PARTS LIST
2-l
INSTRUCTION
MANUAL26-81
2-2
INSTRUCTION MANUAL 26-81
2-3
INSTRUCTION MANUAL 26-81
2-4
INSTRUCTION MANUAL 26-81
2-5
INSTRUCTION MANUAL 26-81
2-6
INSTRUCTION MANUAL 26-81
SHORT LONG
MAINSPRING AIR 1s~~ 24-HR FLOOR WALL WALL
HOUSING MOTOR CLOCK CLOCK STAND MOUNT MOUNT
2-7
INSTRUCTION
MANUAL26-81
FIGURE2-2. DIAPHRAGM-TYPE
WEIGHTUNIT
2-8
INSTRUCTION MANUAL 26-81
2-9
INSTRUCTION MANUAL 26-81
2-10
INSTRUCTION MANUAL 26-81
2-11
INSTRUCTION MANUAL 26-81
20'
IS-
17-
43
15
2-12
INSTRUCTION MANUAL 26-81
2-13
INSTRUCTION MANUAL 26-81
2-14
INSTRUCTION MANUAL 26-81
2-15
INSTRUCTION MANUAL 26-81
3
8
13
‘\
2-16
INSTRUCTION MANUAL 26-81
2-17
INSTRUCTION MANUAL 26-81
12
/
!
11
2-18
INSTRUCTION MANUAL 26-81
2-19
INSTRUCTION MANUAL 26-81
** Use with Type EB sensator for deadline loads between 35,000 and 50,000 lbs
(15,680 and 22,400 daN; 15,909 and 22,727 kg).
*** Use with Type EB sensator for deadline loads between 55,000 and 100,000 lbs
(24,640 and 448,000 daN; 25,000 and 45,455 kg).
2-21
INSTRUCTION MANUAL 26-81
I3
1Z
17
2-22
/
INSTRUCTION MANUAL 26-81
2-23
INSTRUCTION MANUAL 26-81
** Replaces 261280-101
2-24
INSTRUCTION MANUAL 26-81
i
FIGURE 2-8. PUMP PRESSUREUNIT
2-25
INSTRUCTION MANUAL 26-81
t I
I A
2-26
INSTRUCTION MANUAL 26-81
2-27
INSTRUCTION MANUAL 26-81
26-811-2 \
32
2-28
INSTRUCTION MANUAL 26-81
2-29
INSTRUCTION MANUAL 26-81
2-30
INSTRUCTION MANUAL 26-81
2-31
INSTRUCTION MANUAL 26-81
/
FLEXIBLE
TACHOMETER GENERATOR COUPLING RIGHT-ANGLE DRIVE
*6-n/-1* WITH TERMINAL BOX INSTALLATION
2-32
INSTRUCTION MANUAL 26-81
2-33
INSTRUCTION MANUAL 26-81
2-34
INSTRUCTION MANUAL 26-81
2-35
INSTRUCTION MANUAL 26-81
2-36
INSTRUCTION MANUAL 26-81
2-37
INSTRUCTION MANUAL 26-81
2-38
INSTRUCTION MANUAL 26-81
2-39
INSTRUCTION
MANUAL26-81
FIGURE2-14. HYDRAULIC
TORQUE
UNIT
2-40
INSTRUCTION MANUAL 26-81
2-4 1
INSTRUCTION MANUAL 26-81
15
II
2-42
INSTRUCTION MANUAL 26-81
2-43
INSTRUCTION MANUAL 26-81
2-44
INSTRUCTION
MANUAL26-81
FIGURE2-16. ELECTRICTORQUE
UNIT (Sheet 1 of 2)
2-45
INSTRUCTION
MANUAL26-81
\ /
---. ----
FIGURE2-16. ELECTRICTORQUE
UNIT (Sheet 2 of 2)
2-46
INSTRUCTION MANUAL 26-81
2-47
INSTRUCTION
MANUAL26-81
FIGURE2-17. ELECTRICTORQUE
SHUNTBOXASSEMBLY
2-48
INSTRUCTION MANUAL 26-81
2-17- 261375-101 SHUNT BOX ASSY, Electric torque (for ... .REF A
1.219/1.438 dia cable) (See 2,
Figure 2-16 for NHA)
263175-102 SHUNT BOX ASSY, Electric torque (for ... .REF B
1.438/1.875 dia cable) (See 2,
Figure 2-16 for NHA)
-1 949822-005 . CONNECTOR,Watertight, l-1/2" ....... 2 A
949822-006 . CONNECTOR,Watertight, 2" ......... 2 B
-2 979439-015 .O-RING .................. .
-3 948108-006 . LOCKNUT (AP) ............... 2 A
948108-007 . LOCKNUT (AP) ............... 2 B
-4 STD HDW . BOLT, Hex hd, 3/8-24 x 3/4, sst (AP) ... 2
-5 999310-015 . WASHER, Flat, 3/8, sst (AP) ........ 2
-6 999321-008 . LOCKWASHER,3/8, sst (AP) ......... 2
-7 950807-008 . LUG, Cable (for 500,000 to 750,000 .... 2
circ mil cable)
-8 STD HDW . NUT, Hex, heavy, l/2-13, sst (AP) ..... 2
-9 STD HDW . LOCKWASHER,l/2, sst (AP) ......... 2
-10 999310-019 . WASHER, Flat, l/2, sst (AP) ........ 4
-11 STD HDW . BOLT, Hex hd, l/2-13 x l-3/4, sst (AP) . . 2
-12 935624-005 . SHUNT, l,OOOA, 100 mV ....... 1
-12A STD HDW . SCREW, No 8-32 x 5/16, b;ak' ....... REF
-13 STD HDW . SCREW, Bind hd, No 8-32 x 5/8 ....... 2
-14 999310-006 . WASHER, Flat, No 8. ............ 2
-15 STD HDW . LOCKWASHER,No 8. ............. 2
-16 261383-302 . BASE, Shunt ................ 1
-17 261383-301 . BASE, Shunt ................ 1
-18 955701-012 . CONNECTOR,Watertight, l/2" ........ 1
-19 979447-016 .O-RING ................. ..l
-20 948108-002 . LOCKNUT (AP) ............... 2
-21 999212 . DECAL, 'DANGER HIGH VOLTAGE' ....... 1
-22 261376-1 . BOX ASSY, Shunt .............. 1 A
261376-2 . BOX ASSY, Shunt .............. 1 B
2-49
INSTRUCTION MANUAL 26-81
31
22
I
2673119
2-50
INSTRUCTION MANUAL 26-81
2-51
INSTRUCTION MANUAL 26-81
11
2-52
INSTRUCTION MANUAL 26-81
2-53
INSTRUCTION MANUAL 26-81
I:
25
29\
\
‘18
22
\
2-54
INSTRUCTION MANUAL 26-81
2-55
INSTRUCTION MANUAL 26-81
2-56
INSTRUCTION MANUAL 26-81
2-20-7 260581-101 .. HOUSING ASSY, Air motor (See Figure ... 1 G-L,
2-25 for breakdown) s-x
-8 260595-101 .. REGULATOR-OILERASSY, Air motor ..... 1 G-L,
(See Figure 2-26 for breakdown) s-x
-9 264100-102 . BOX, Chart (welded assy) ......... 1
-10 See Table 2-2 . CHART (English) .............. 1
See Table 2-3 . CHART (Metric) .............. 1
See Table 2-4 . CHART(SI) ................ .
-11 260332-101 . PEN ASSY (bonded assy) (red ink) ..... 6
260332-102 . PEN ASSY (bonded asy) (blue ink) ..... 6
-12 . RECORDERASSY, with 12-hr clock ...... 1 A-L
(See Figure 2-29 for breakdown)
. RECORDERASSY, with 24-hr clock ...... 1 M-X
(See Figure 2-29 for breakdown)
263460 . STAND ASSY, Floor ............. 1 A,B,G,H,
M,N,S,T
-13 264095-303 .. PLATE, Support ............. 1
-14 STD HDW . . NUT, Hex, l/2-13, sst (AP) ....... 4
-15 999310-019 .. WASHER, Flat, l/2, sst (AP) ....... 4
-16 STD HDW . . BOLT, Hex hd, l/2-13 x l-1/4, sst (AP) . 4
-17 260462-101 .. UPRIGHT ASSY, Floor stand, RH ...... 1
(welded assy)
-18 260461-101 .. UPRIGHT ASSY, Floor stand, LH ...... 1
(welded assy)
263437 . MOUNTASSY, Wall, short .......... 1 C,D,I, J,
Q,P,U,V
-19 264095-302 .. PLATE, Support ............. 1
-20 STD HDW .. NUT, Hex, l/2-13, sst (AP) ....... 2
-21 999310-019 .. WASHER, Flat, l/2, sst (AP) ....... 2
-22 STD HDW . . BOLT, Hex hd, l/2-13 x l-1/4, sst (AP) . 2
-23 260435 .. POST, Spacer, long ........... 2
-24 STD HDW . . BOLT, Hex hd, l/2-13 x l-1/2, sst (AP) . 4
-25 999310-019 .. WASHER, Flat, l/2, sst (AP) ....... 4
-26 260434 .. POST, Spacer, short ........... 2
-27 STD HDW . . BOLT, Hex hd, l/2-13 x l-1/2, sst (AP) . 4
-28 999310-019 .. WASHER, Flat, l/2, sst (AP) ....... 4
-29 260439 .. UPRIGHT ASSY, Short wall mount, LH ... 1
-30 260438 .. UPRIGHT ASSY, Short wall mount, RH ... 1
263430 . MOUNTASSY, Wall, long .......... 1 E,F,K,L,
Q,%W,X
-31 264095-303 .. PLATE, Support ............. 1
-32 STD HDW .. NUT, Hex, l/2-13, sst (AP) ....... 2
-33 999310-019 .. WASHER, Flat, l/2, sst (AP) ....... 2
-34 STD HDW . . BOLT, Hex hd, l/2--13 x 1, sst (AP) ... 2
-35 260435 .. POST, Spacer, long ........... 2
-36 STD HDW . . BOLT, Hex hd, l/2-13 x l-1/2, sst (AP) . 4
-37 999310-019 .. WASHER, Flat, l/2, sst (AP) ....... 4
-38 260434 .. POST, Spacer, short ........... 2
-39 STD HDW . . BOLT, Hex hd, l/2-13 x l-1/2, sst (AP) . 4
-40 999310-019 .. WASHER, Flat, l/2, sst (AP) ....... 4
-41 260432 .. UPRIGHT ASSY, Long wall mount, LH .... 1
-42 260431 .. UPRIGHT ASSY, Long wall mount, RH .... 1
2-57
INSTRUCTION MANUAL 26-81
RECORDER
CHANNEL r 1 2 3,4,5 AND 6
400/800
1 24 400/800 400/800 1200/1600
263124 X X
263125 X
263144-301 X
263144-302* X
263145 X
263146* X
<ECORDER
XANNEL 1 3 3,4,5, AND 6
540/720
263128 X X
263149 X X
263150 X X
2-58
INSTRUCTION MANUAL 26-81
TABLE 2-4. RECORDERCHARTS - SI
KLLUWliK
CHANNEL 3,4,5 AND 6
l--r
PENETRATION FLUID PRESSURE,
PUMP STROKES,
TORQUE,
RPM,
% MUD FLOW,
12 24 % PIT LEVEL
263193 X
263194 X
263195 X
263196 X
2-59
INSTRUCTION MANUAL 26-81
2-60
INSTRUCTION MANUAL 26-81
2-61
INSTRUCTION MANUAL 26-81
2-62
INSTRUCTION MANUAL 26-81
2-63
INSTRUCTION MANUAL 26-81
2-64
INSTRUCTION MANUAL 26-81
2-65
INSTRUCTION MANUAL 26-81
2-66
INSTRUCTION MANUAL 26-81
2-67
INSTRUCTION MANUAL 26-81
2
11
6-
5-
2-68
INSTRUCTION MANUAL 26-81
2-69
INSTRUCTION MANUAL 26- 81
/
/
/’ /I 4
2-70
INSTRUCTION MANUAL 26-81
2-28- 260594-101 OILER ASSY, Air motor (See 10, Figure 2-26 . REF
for NHA)
-1 261196 . LABEL, "TOTCO REGULATORAND OILER" . . . . 1
972313-001 . LUBRICATOR 1
-2 . . RING ASSY, Clamp (Wilkerson) (not . . . 1
normally replaced)
-3 + . . O-RING................. 1
GRP-95-613 . . BOWLASSY (Wilkerson) . . . . . . . . . 1
-4 972313-018 . . . BOWL, Metal . . . . . . . . . . . . . 1
-5 GRP-95-705 . . . GAUGE, Sight (Wilkerson) . . . . . . . 1
-6 . . . DRAIN COCK (Wilkerson) . . . . . . . . 1
-7 LRP-96-137 . . TUBE ASSY, Siphon (Wilkerson) . . . . . 1
-8 972313- 023+ . . O-RING................. 1
-9 LRP-30-415 . . ADAPTER (Wilkerson). . . . . . . . . . . 1
-10 LRP-40-004 . . BALL (Wilkerson) . . . . . . . . . . . . 1
-11 972313- 027 . . FLOW GUIDE . . . . . . . . . . . . . . . 1
-12 . . SCREW, Flow guide (Wilkerson) . . . . . 1
-13 . . TUBE, Spacer (Wilkerson) . . . . . . . . 1
-14 972313-013 . . SCREW, Adjustment . . . . . . . . . . . 1
-15 972313- 023+ . . O-RING................. 1
-16 972313-002** . DOME,Sight .............. 1
-17 972313- 022**/+: .O-RING ................. 2
-18 .. FILL PLUG (Wilkerson) ......... 1
-19 + .. O-RING (Wilkerson) ........... 1
-20 GRP-49-023 .. CHECK VALVE (Wilkerson) ........ 1
-21 . . BODY ASSY (Wilkerson) (not normally . . 1
replaced separately)
972313-012 KIT, Repair, dome ............. REF
972313-011 KIT, Repair, o-ring ............ REF
2-71
INSTRUCTION
MANUAL26-81
FIGURE2-29. RECORDER
ASSEMBLY
(Sheet 2 of 4)
2-73
INSTRUCTION
MANUAL26-81
/
/
/
DETAIL A
FIGURE2-29. RECORDER
ASSEMBLY
(Sheet 3 of 4)
2-74
INSTRUCTION MANUAL 26-81
DETAIL C $6
2-75
INSTRUCTION MANUAL 26-81
2-76
INSTRUCTION MANUAL 26-81
2-77
INSTRUCTION MANUAL 26-81
2-78
INSTRUCTION MANUAL 26-81
2-29-75 STD HDW . . SCREW, Sot hd, l/4-20 x 5/8, sst (AP) . . 2
260261 . . LEVER ASSY, Clutch . . . . . . . . . . . 1
-76 STD HDW . . SCREW, Sot hd, l/4-20 x 7/8, sst (AP) . . 2
-77 999310-012 . . WASHER, Flat (AP) . . . . . . . . . . . . 2
-78 999254-018 . . . RING, Retaining . . . . . . . . . . . . 2
-79 260263 . . . SHAFT, Bracket . . . . . . . . . . . . 1
-80 260252-101 . . . LEVER ASSY, Clutch (press fit assy) . . 1
-81 260262-301 . . . BRACKET, Clutch lever . . . . . . . . . 1
-82 260264 . . BEARING ASSY, clutch (press fit assy) . . 1
-83 STD HDW . . SCREW, Flat hd, No 4-40 x 3/8, sst (AP) . 3
-84 260925 . . LEVER, On-off . . . . . . . . . . . . . . 1
-85 STD HDW . . SCREW, Sot hd, l/4-20 x 3/8, sst (AP) . . 2
-86 999216-015 . . WASHER . . . . . . . . . . . . . . ...2
-87 262254 . . BEARING ASSY, On-off lever . . . . . . . 1
(press fit assy)
-88 STD HDW . . SCREW, Sot hd, No lo-24 x 3/8, sst (AP) . 3
-89 260955 . . LINK, Clutch shaft to penetration . . . . 1
pen arm
- 90 982600-013 . . COLLAR, Shaft (includes setscrew) . . . . 1
-91 260956 . . ANCHOR . . . . . . . . . . . . . . . ..l
- 92 STD HDW . . NUT, Hex, No 10-32, sst (AP). . . . . . . 1
-93 260257 . . COLLAR . . . . . . . . . . . . . . . ..l
-94 STD HDW . . SETSCREW,Cup pt, sot hd, No lo-32 x . . 1
5/16 (AP)
-95 STD HDW . . SETSCREW,Cup pt, sot hd, No lo-32 x . . 1
l/2
-96 260266 . . SPRING..................1
- 97 260722-301 . . LEVER, Remote control . . . . . . . . . . 1
- 98 STD HDW . . SETSCREW,Cup pt, sot hd, No lo-32 x . . 2
5/16 (AP)
- 99 260260-301 . . CAM, Clutch. . . . . . . . . . . . . . . 1
- 100 999290-011 . . PIN, Spring (AP). . . . . . . . . . . . . 1
-101 260251 . . SHAFT, Clutch . . . . . . . . . . . . . . 1
-102 260242 . . BUTTONASSY, Release, top cover . . . . . 1
-103 999246-010 . . PIN, Spring . . . . . . . . . . . . . . . 1
-104 260243 . . SPRING, Release . . . . . . . . . . . . . 1
-105 264120-301 . . PLATE, Nomenclature-on/off, English . . . 1 C
264120-302 . . PLATE, Nomenclature-on/off, Metric. . . . 1 D
264120-303 . . PLATE, Nomenclature-on/off, SI. . . . . . 1 E
-106 STD HDW . . SCREW, Bind hd, No 8-32 x 3/8, sst (AP) . 4
-107 260728 . . LABEL, Instruction. . . . . . . . . . . . 1
-108 STD HDW . . SCREW, Hex hd, 1/2-13x1, sst. . . . . . . 4
-109 263904-101 . . HOUSING ASSY, Recorder, English/SI. . . . 1 C,E
(See Figure 2-41 for breakdown)
263904-102 . . HOUSING ASSY, Recorder Metric . . . . . . 1 D
(See Figure 2-41 for breakdown)
2-79
INSTRUCTION MANUAL 26-81
2-80
INSTRUCTION MANUAL 26-81
2-81
INSTRUCTION
MANUAL26-81
FIGURE2-31. CHARTDRUMASSEMBLY
2-82
INSTRUCTION MANUAL 26-81
2-83
INSTRUCTION
MANUAL26-81
FIGURE2-32. HOUSINGCOVERASSEMBLY
2-84
INSTRUCTION MANUAL 26-81
2-85
INSTRUCTION MANUAL 26-81
2- 86
INSTRUCTION MANUAL 26-81
2-87
INSTRUCTION MANUAL 26-81
2-34- 261120-101 PEN ARM ASSY, Weight (See 23, ....... REF
Figure 2-29 for NHA)
-1 STD HDW . SCREW, Sot hd, No 8-32 x 3/8, sst (AP) . . 1
-2 261244 . PLUG, Nylon ............... 1
-3 STD HDW . SCREW, Hex hd, No 8-32 x 3/4, sst. .... 1
-4 STD HDW . WASHER, Flat, No 8, sst. ......... 1
-5 261122 .SPRING .................. 1
-6 261140 . HOLDER, Pen ............... 1
-7 261124 . ARM ASSY (press fit assy) ........ 1
-8 STD HDW . SCREW, Sot hd, No 5-40 x l/2, sst (AP) . . 4
-9 STD HDW . LOCKWASHER,Split, No 5, sst (AP). .... 4
-10 STD HDW . SCREW, Sot hd, No 4-40 x 3/4, sst. .... 1
-11 261132 .BUSHING ................. 1
-12 261130 . CLEVIS, Pen arm ............. 1
-13 261133-301 . PLATE, Index, 6, 8 or 8, 10, 12 lines . . 1
-14 STD HDW . SCREW, Sot hd, No 2-56 x 3/16 (AP) .... 2
-15 261129 . SCREW, Clamp, slider ........... 1
-16 261128 . SLIDER, Arm ............... 1
-17 261127 .KNOB.Slider ............... 1
-18 STD HDW . SETSCREW,Cup pt, No 8-32 x 3/16, sst (AP) 1
-19 261126 . LOCATOR, Slider ............. 1
-20 STD HDW . SCREW, Sot hd, No 6-32 x 318, sst. .... 2
-21 STD HDW . WASHER, Flat, No 6, sst. ......... 2
-22 261137 . BRIDGE, Bracket ............. 1
-23 261125 . ARM ASSY, Ratio (press fit assy) ..... 1
-24 261136 . PILLAR, Bracket ............. 2
-25 261135 . BRACKET, Pen arm. ............ 1
2-88
--
I
INSTRUCTION
MANUAL26-81
. - --- _-- __
FIGURE2-34. W E IGHTPENA R MASSEMBLY
2-89
INSTRUCTION MANUAL 26-81
2-90
INSTRUCTION MANUAL 26-81
2-91
INSTRUCTION
MANUAL26-81
2-37- 260963-101 INDEX ASSY, Hub, English/S1 (See 31, .... REF A
Figure 2-29 for NHA)
260963-102 INDEX ASSY, Hub, Metric (See 31, ...... REF B
Figure 2-29 for NHA)
-1 999317-023 . RING, Retaining ............. 1
-2 260940 . PENTAGON, Index, English/S1 ....... 1 A
260966* . PLATE, Index, Metric ........... 1 B
-3 999290-001 . ROLLPIN (AP) ............... 1
260939 . GEAR ASSY, Index, Eng/SI (staked assy) . . 1 A
260965 . GEAR ASSY, Index, Metric (staked assy) . . 1 B
-4 260831 .. PIN, Drive ............... NP
-5 260968 .. GEAR, 120 tooth, English/S1 ...... NP A
260832 .. GEAR, 116 tooth, Metric ........ NP B
-6 260938 . SPRING, Friction ............. 1
260937 . DISC ASSY, Index, English/S1 ....... 1 A
260830 . DISC ASSY, Index, Metric ......... 1 B
-7 260967 .. PIN, Drive ............... 5 A
260967 .. PIN, Drive ............... 4 B
-8 260936 .. HUB, Index (press fit in item -9) ... 1
-9 260969 .. DISC, English/S1 ............ 1 A
260964* .. DISC, Metric .............. 1 B
260945 CAM SHAFT ASSY, Index (See 36, Figure 2-29 . REF
for NHA)
-10 260947 .CAM,Index................ 1
-11 STD HDW . SCREW, Sot hd, cap, No 8-32 x 3/4 (AP) . . 1
-12 260946 . SHAFT,Cam................ 1
-13 999276- 005 .ROLLPIN . . . . . . . . . . . . . . . . . 1
2-93
INSTRUCTION MANUAL 26-81
2-95
INSTRUCTION MANUAL 26-81
,; ’
;; FIFTH PEN POSITION , /,5’ .
_‘,’
,,;’
, ‘, ’
r-x’
I, ‘.’
Zl-------
14
12
!i
r
2- 96
INSTRUCTION MANUAL 26-81
2-39- 263625-101 BRACKET ASSY, Multiple pen arm (See 46, . . REF
Figure 2-29 for NHA)
261351-101 .PENARMASSY............... 4
-1 STD HDW . SCREW, Allen cap, No 8-32 x l/2, sst (AP). 8
-2 STD HDW . WASHER, Flat, No 8 . . . . . . . . . . . . 8
-3 STD HDW . . SCREW, Pen pressure adjust, hex hd, . . 1
No 8-32 x 0.75, sst
-4 STD HDW . . WASHER, Flat, light, No 8, sst . . . . . 1
-5 261122 . . SPRING, Pen pressure . . . . . . . . . . 1
-6 261140 . . HOLDER, Pen . . . . . . . . . . . . . . 1
-7 261338-101 . . ARM ASSY (press fit assy). . . . . . . . 1
-8 STD HDW . SCREW, Sot hd, No 8-32 x 3/8, sst (AP) . . 3
-9 STD HDW . WASHER, Flat, No 8 (AP). . . . . . . . . . 3
-10 262615 . PIN, Dowel, bridge . . . . . . . . . . . . 2
-11 263617 .BRIDGE.................. 1
264063-109 . LEVER ASSY, Pen arm, third pen position . 1 A
264063-102 . LEVER ASSY, Pen arm, fourth pen position . 1 B
264063-107 . LEVER ASSY, Pen arm, fifth pen position . 1 C
264063-104 . LEVER ASSY, Pen arm, sixth pen position . 1 D
-12 999246- 008 . . ROLLPIN . . . . . . . . . . . . . . . . 1 A
-13 999246- 008 . . ROLLPIN . . . . . . . . . . . . . . . . 2 B-D
-14 263608 . . LEVER, Pen arm, third pen position . . . 1 A
-15 265058-301 . . LEVER, Pen arm, fourth thru sixth . . . 1 B-D
pen positions
-16 263624-101 . . CHANNELASSY, Clevis lever (staked assy) 1 B,D
-17 STD HDW . . SCREW, Sot hd, No lo-32 x 3/8, sst (AP). 1 B,D
-18 STD HDW . . WASHER, No 10, sst (AP). . . . . . . . . 1 B,D
-19 263613-301 . . LEVER, Clevis, fourth and sixth pen . . 1 B,D
positions
-20 263602 . . LEVER, Clevis, fifth pen position . . . 1 C
-21 264070-301 . . SHAFT, Pen arm lever, third pen position 1 A
-22 264070-302 . . SHAFT, Pen arm lever, fourth pen . . . . 1 B
position
-23 264070-303 . . SHAFT, Pen arm lever, fifth pen position 1 C
-24 264070-304 . . SHAFT, Pen arm lever, sixth pen position 1 D
-25 263616 .BRACKET . . . . . . . . . . . . . . . . . 1
2-97
INSTRUCTION MANUAL 26-81
2-98
INSTRUCTION MANUAL 26-81
2-40- 260801-101 AIR CYLINDER ASSY (See 51, Figure 2-29 ... REF
for NHA)
-1 260804 . BASE, Air cylinder ............ 1
-2 STD HDW . NUT, Hex, l/4-20, sst (AP) ........ 2
-3 STD HDW . LOCKWASHER,Split, l/4, sst (AP) ..... 2
-4 STD HDW . SCREW, Flat hd, l/4-20 x 2-l/8, sst (AP) . 2
-5 260803 .cAM ................... 1
-6 999243-009 .SETSCREW ................. 1
-7 968638-001 .ELBOW, Male ............... 1
978916-002 . CYLINDER ASSY .............. 1
-8 978916-015 .. TIEROD ................ 2
-9 STD HDW .. LOCKWASHER,Split, No. 10, sst ..... 2
-10 978916-017 .. CAP .................. 1
-11 978916-011 .. GASKET, Cylinder ............ 2
-12 F153-0822 .. CYLINDER (Bellows Co.) ......... 1
-13 978916-012 .. PISTON & ROD ASSY ........... 1
-14 978916-014 .. O-RING ................. 1
-15 978916-013 .. O-RING ................. 1
-16 978916-016 .. HEAD .................. 1
-17 260802 . SPRING (Color coded gray stripe) ..... 1
-18 260716-302 . SPACER, Piston rod ............ 1
2-99
INSTRUCTION MANUAL 26-81
7
17
/
2-101/2-102
INSTRUCTION MANUAL 26-8 1
SECTION III
NUMERICAL INDEX
3-l
INSTRUCTION MANUAL 26-81
3-2
INSTRUCTION MANUAL 26-81
-
FIGURE AND FIGURE AND
PART NUMBER INDEX NUMBER PART NUMBER INDEX NUMBER
3-3
INSTRUCTION MANUAL 26-81
3-4
INSTRUCTION MANUAL 26-81
3- 5
INSTRUCTION MANUAL 26-81
3- 6
INSTRUCTION MANUAL 26-81
3- 7
INSTRUCTION MANUAL 26-81
3- 8
INSTRUCTION MANUAL 26-81
3-9
INSTRUCTION MANUAL 26-81
3-10
INSTRUCTION MANUAL 26-81
3-11/3-12
INSTRUCTION MANUAL 26-8 1
SECTION IV
SPARE PARTS LIST
4-l GENERAL
4-2 This section contains information for parts which are recommended for
stocking as spares. Spare parts list, Table 4-1, includes back-up spare
parts and items which should be replaced during disassembly or overhaul of system
components. An inventory of readily available spare parts will reduce the loss of
equipment operating time when repairs are necessary. Table 4-l does not list
standard hardware items. Sufficient information for obtaining these items is
contained in the Group Assembly Parts List, Section 11.
4-3 Customer selection of spare parts from the list in Table 4-l will vary with
equipment specifically supplied (i.e. sensors etc.) for use with the drilling
recorder. Locate and identify each recommended item in the appropriate illustration
in Section II and determine if the item should be stocked as a spare part.
4-4 Recommended spare parts for equipment associated with the drilling recorder
system are given in appropriate instruction manuals listed under RELATED
PUBLICATIONS.
4-l
INSTRUCTION MANUAL 26-81
FIGURE & PY
INDEX NO. PART NUMBER DESCRIPTION USED
4-2