Beruflich Dokumente
Kultur Dokumente
USER MANUAL
TABLE OF CONTENTS
●Dimensions
●Introduction
●Specification
●Connection diagram
●Betaflight settings
Dimensions
3mm
30
.5m
m
8mm
36 m
m m
m . 75
40
⑴
Introduction
Specification:
●Up to 8S input (max 36V)
●5V BEC up to 3A continuous
●STM32F722 MCU
●MPU6000 Gyro/ACC for smooth performace
●128MB OnBoard flash
●OSD chip Onboard
●6 available UARTS
●VTX switch to control the ON/OFF of the VTX
directly from your transmitter
●LC Filter for 5V VTX
●USB Type C connector
●Onboard RGB LED distribution for clean wiring
to the LED on the arm of the quad.
●Onboard RBG LED
●Notch desing on sides and in the front of the FC
for better fitting on the frame.
⑵
Connection diagram
TOP connection:
CAM- CONTROL
(JOYSTICK EMULATION)
UART6-TX
ESC-TEL
UART6-RX (UART1-RX)
CURR
UART5-RX
VBAT+
UART5-TX
M4
CAM M3
GND
VIDEO-IN M2
5V
GND M1
GND
5V-CAM VBAT+
BOOT
BUTTON
5V 3.3V
GND RX VOLTAGE
GND SELECTOR
5V
UART4-RX
UART4-TX
UART4-RX
UART2-TX
5V
GND
5V
BUZZER-
5V VBAT
UART3-TX
VTX VOLTAGE
VIDEO SELECTOR
OUT TO
VTX
VIDEO GND
GND
5V-OUT
FROM VTX
⑶
BOTTOM connection:
M2
M1 M3
GND M4
CURRENT
VBAT+ SENSOR
ESC-TELEMETRY
(UART1-RX)
GND LED-STRIP
5V 5V
LED-STRIP GND
GND
5V
UART4-RX
UART4-TX
GND LED-STRIP
5V 5V
LED-STRIP GND
5V
VTX
VOLTAGE
BUZZER-
GND
5V-OUT
FROM-VTX
VIDEO
GND UART3-TX
VIDEO OUT
TO VTX
⑷
Betaflight settings
Receiver chapter:
TBS Crossfire:
GND
5V
UART4-RX
UART4-TX
⑸
FrSky RXSR:
Don’t forget to make the solder bridge in the left side of the Solder jumper near the RX pad to select 5V
! as voltage for the RX
GND
5V
UART2-TX
UART4-RX
⑹
FrSky XM+:
GND
5V
UART4-RX
⑺
Spektrum DMSX FPV:
Don’t forget to make the solder bridge in the right side of the Solder jumper near the RX pad to select 3.3V
! as voltage for the RX
SELECT
VOLTAGE
3.3V
GND
3.3V
UART4-RX
⑻
FlySky A8S:
Don’t forget to make the solder bridge in the left side of the Solder jumper near the RX pad to select 5V
! as voltage for the RX
SELECT
VOLTAGE
5V
GND
5V
UART4-RX
⑼
VTX chapter:
5V VTX:
Assign the AUX you prefer from your radio to turn ON and OFF the VTX from the transmitter from USER1 mode in
! BetaFlight. If USER1 is not active the VTX will remain OFF.
Don’t forget to make the solder bridge in the left side of the Solder jumper near the VTX pad to select 5V
as voltage for the VTX
5V
5V
GND
5V-OUT
VIDEO-GND
VIDEO-OUT
UART3-TX
⑽
HV VTX:
Assign the AUX you prefer from your radio to turn ON and OFF the VTX from the transmitter from USER1 mode in
! BetaFlight. If USER1 is not active the VTX will remain OFF.
Don’t forget to make the solder bridge in the right side of the Solder jumper near the VTX pad to select VBAT
as voltage for the VTX
VBAT
VBAT+
GND
5V-OUT
VIDEO-GND
VIDEO-OUT
UART3-TX
⑾
Camera chapter:
UART control Camera:
! Don’t forget to make the solder bridge in the right side of the Solder jumper near the camera pad to select UART6-TX
5V
GND
VIDEO
VBAT+
UART6-RX
UART6-TX
UART6-TX
⑿
Joystick Emulation Camera Control:
For Joystick emulation everything is already set up in the firmware, you just need to wire your camera as shown
below and don’t forget to make the solder bridge in the left side of the solder jumper.
5V
GND
VIDEO
CAM- CONTROL
CAM- CONTROL
(JOYSTICK
EMULATION)
⒀
LED Betaflight setup and connection: