Beruflich Dokumente
Kultur Dokumente
DSP PRO
Digitaler 10-Kanal Signalprozessor
Digital 10-channel signal processor
Herzlichen Glückwunsch!
Sehr geehrter Kunde, Dieser Prozessor wurde von uns nach neuesten
technischen Erkenntnissen entwickelt und zeichnet
Wir gratulieren Ihnen zum Kauf dieses hochwer- sich durch hervorragende Verarbeitung und eine
tigen HELIX Signalprozessors. überzeugende Anwendung ausgereifter Technolo-
gien aus.
Audiotec Fischer setzt mit dem HELIX DSP PRO
neue Maßstäbe im Bereich der Signalprozessor- Viel Freude an diesem Produkt wünscht Ihnen das
technik. Dabei profitieren Sie als Kunde direkt von Team von
unserer nahezu 30-jährigen Erfahrung in der For-
schung und Entwicklung von Audiokomponenten. AUDIOTEC FISCHER
Allgemeine Hinweise
Allgemeines zum Einbau von HELIX-Kompo- tungen, der Benzintank etc. dahinter verborgen
nenten sind. Diese könnten sonst beschädigt werden. Ach-
ten Sie bitte darauf, dass sich solche Teile auch in
Um alle Möglichkeiten des Produktes optimal aus- der doppelten Wandverkleidung verbergen können.
schöpfen zu können, lesen Sie bitte sorgfältig die
nachfolgenden Installationshinweise. Wir garantie- Allgemeines zum Anschluss des HELIX DSP
ren, dass jedes Gerät vor Versand auf seinen ein- PRO
wandfreien Zustand überprüft wurde.
Der DSP darf nur in Kraftfahrzeuge eingebaut wer-
Vor Beginn der Installation unterbrechen Sie den, die den 12V-Minuspol an Masse haben. Bei
den Minusanschluss der Autobatterie. anderen Systemen kann der HELIX DSP PRO und
Wir empfehlen Ihnen, die Installation von einem die elektrische Anlage des Kfz beschädigt werden.
Einbauspezialisten vornehmen zu lassen, da der
Nachweis eines fachgerechten Einbaus und An- Verwenden Sie zum Anschluss des Prozessors
schlusses des Gerätes Voraussetzung für die Ga- an die Stromversorgung des Fahrzeugs aus-
rantieleistungen sind. schließlich den beiliegenden Anschlussstecker
oder das optional erhältliche Easy Plug Kabel!
Installieren Sie Ihren DSP PRO an einer trockenen Die Verwendung eines anderen Kabels kann zu
Stelle im Auto und vergewissern Sie sich, dass Schäden an Ihrer Anlage und des Prozessors
der Verstärker am Montageort genügend Kühlung führen!
erhält. Montieren Sie das Gerät nicht in zu kleine,
abgeschlossene Gehäuse ohne Luftzirkulation Die Kabelverbindungen müssen so verlegt sein,
oder in der Nähe von wärmeabstrahlenden Teilen dass keine Klemm-, Quetsch- oder Bruchgefahr
oder elektronischen Steuerungen des Fahrzeuges. besteht. Bei scharfen Kanten (Blechdurchfüh-
Im Sinne der Unfallsicherheit muss der Prozessor rungen) müssen alle Kabel gegen Durchscheuern
professionell befestigt werden. Dieses geschieht gepolstert sein. Ferner darf das Versorgungskabel
über Schrauben, die in eine Montagefläche ein- niemals mit Zuleitungen zu Vorrichtungen des Kfz
geschraubt werden, die wiederum genügend Halt (Lüftermotoren, Brandkontrollmodulen, Benzinlei-
bieten muss. tungen etc.) verlegt werden.
1 2 3 4 5 6 7
1 Line Input
Cinch-Eingänge zum Anschluss eines Vor-
5 Clipping LED
Diese LED leuchtet rot, wenn einer der Ana-
verstärkersignals logeingänge übersteuert wird
2
Coax Input 6 Highlevel Input
Elektrischer Eingang im SPDIF-Format für Hochpegel-Lautsprechereingang zum An-
digitale Stereosignale schluss von Werksradios oder Radios ohne
Vorverstärkerausgänge
3 Input Switch
Umschalter zwischen „Coax Input“ und „Opti- 7 Power Input
cal Input“ Zum Anschluss an die Bordnetzspannung
mit einem zusätzlichen Remote Ein- und
4 Optical Input Ausgang. Der Remote-Ausgang muss in je-
Optischer Eingang im SPDIF-Format für digi- dem Fall zur Einschaltung der Verstärker ge-
tale Stereosignale nutzt werden
8 9 10 11 12 13
4
Signal als den Remote-Ausgang, um ange- ware ein neues DSP Setup eingespielt werden.
schlossene Verstärker einzuschalten!
11 USB Eingang
8 Masseschalter Mit Hilfe dieses Eingangs wird der HELIX DSP
Beim HELIX DSP PRO ist die Masse der Signalein- PRO über das beiliegende Kabel mit dem Com-
gänge galvanisch von der Masse der Signalaus- puter verbunden und kann anschließend über das
gänge getrennt. DSP PC‑Tool konfiguriert werden.
Dies ist in den meisten Fahrzeugen die beste Op-
tion, um Störgeräusche wie z.B. von der Licht- 12 Control Input
maschine zu unterbinden. Allerdings gibt es auch Dieser Multifunktionseingang dient zum Anschluss
Fälle, wo die Massen der Eingänge mit den Aus- von HELIX Zubehörprodukten, wie beispielsweise
gängen direkt „hart“ oder über einen 200 Ohm-Wi- einer Fernbedienung, mit deren Hilfe diverse Funk-
derstand „weich“ verbunden werden müssen. Der tionen des Prozessors gesteuert werden können.
Masseschalter hat drei Positionen: Die Funktionalität muss je nach Typ der Fernbe-
- Mittelstellung: Massen galvanisch getrennt dienung zuerst im „Device Configuration Menu“ der
- Linksanschlag: Massen „hart“ zusammenge- DSP PC-Tool Software oder an der Fernbedienung
schaltet selbst konfiguriert werden.
- Rechtsanschlag: Massen „weich“ gekoppelt
13 Line Output
9 Control Taster 10-Kanal Vorverstärkerausgang zum Anschluss
Mit Hilfe des Control Tasters lässt sich zwischen von Verstärkern. Die maximale Ausgangsspannung
den Speicherbereichen eins und zwei umschalten. beträgt 6 Volt. Die Ausgänge können in der DSP
Zum manuellen Umschalten der zwei Setups muss PC-Tool Software den Eingängen beliebig zugeord-
der Control Taster eine Sekunde lang gedrückt wer- net werden.
den. Der Umschaltvorgang wird durch einmaliges
rotes Blinken der Status LED angezeigt.
Wird der Taster länger als 5 Sekunden gedrückt,
so wird das Gerät resettet und der gesamte interne
Speicher gelöscht! Anschließend wird dies durch
ein rotes Dauerblinken der Status LED angezeigt.
Achtung: Nach dem Resetten des Gerätes kann
der HELIX DSP PRO keine Audiosignale mehr wie-
dergeben, bis ein neues Sound Setup eingespielt
wurde.
10 Status LED
Die Status LED zeigt das aktuell ausgewählte
Setup des HELIX DSP PRO an. Leuchtet die LED
grün, ist Setup 1 geladen. Bei Setup 2 leuchtet die
LED orange. Sollte sich kein Setup im internen
Speicher befinden, blinkt die LED rot. Sofern letz-
teres der Fall ist, muss über die DSP PC‑Tool Soft-
5
Einbau und Installation
Kanalzuordnung:
Kanal A
Kanal B
Kanal C
Kanal D
Kanal E
Kanal F
Kanal G
Kanal H
Abb. 1
Jumper unten*
Kanal G & H:
2 V 4 V*
Jumper oben
Hochpegel
5 V 10 V* 10 V 20 V
Cinch
2 V 4 V* 2V 4V Kanal G & H:
250 mV 500 mV
30 Ohm Eingangsimpedanz 4 kOhm
Abb. 2 Abb. 3
durch Linksdrehung des jeweiligen Trim- Die Masseleitung muss an einer nicht isolierten
mers bis die Clipping LED aufleuchtet. Dre- Stelle mit dem Kfz-Chassis verbunden werden.
hen Sie nun den Trimmer im Uhrzeigersinn, Nicht ausreichender Massekontakt führt zu
bis die Clipping LED wieder erlischt. unerwünschten Störgeräuschen und Fehlfunk-
6. Wiederholen Sie diesen Vorgang für jeden tionen. Die Plusleitung wird entweder direkt an
genutzten Signaleingang. den Pluspol der Batterie oder an einen Strom-
verteiler angeschlossen, der mit dem Pluspol
4. Anschluss einer digitalen Signalquelle der Batterie verbunden ist. Die Stromaufnahme
Sofern Sie über eine Signalquelle mit koaxi- des HELIX DSP PRO ist mit ca. 450 mA zwar
alem oder optischem Digitalausgang verfügen, sehr gering, trotzdem sollten Kabel mit mind.
kann diese an den Prozessor angeschlossen 1 mm² Querschnitt für die Spannungsversor-
werden. Der HELIX DSP PRO ist werksseitig gung verwendet werden.
so konfiguriert, dass automatisch auf einen der
Digitaleingänge umgeschaltet wird, wenn dort 6. Anschluss des Remote-Eingangs
ein Audiosignal anliegt. Diese Funktion kann Der Remote-Eingang muss mit dem Remote-
über die DSP PC-Tool Software deaktiviert bzw. Ausgang des Radios verbunden sein, sofern
auf einen manuellen Modus (in Verbindung mit die Vorverstärkereingänge des Prozessors als
einer optional erhältlichen Fernbedienung) ge- Signaleingänge genutzt werden. Es wird drin-
ändert werden. gend davon abgeraten den Remote-Eingang
Die Einschaltautomatik des Prozessors funktio- des Prozessors über das Zündungsplus des
niert bei Verwendung des Digitaleingangs nicht, Fahrzeugs zu steuern, um Störgeräusche beim
so dass der Remote-Eingang des „Power Input“ Ein- und Ausschalten zu vermeiden.
zwingend belegt werden muss. Eine gleichzei- Bei Verwendung des Highlevel-Eingangs muss
tige Nutzung der Digitaleingänge sowie der der Remote-Eingang nicht belegt werden, so-
Highlevel- oder der Vorverstärkersignaleingän- fern das angeschlossene Radio über BTL-Aus-
ge ist möglich. gangsstufen verfügt.
Wichtig: Das digitale Audiosignal einer Quel-
le ist üblicherweise nicht Lautstärke geregelt. 7. Anschluss des Remote-Ausgangs
Das bedeutet, dass an den Signalausgängen Dieser Ausgang dient dazu, die angeschlos-
des HELIX DSP PRO der volle Pegel anliegt senen Verstärker mit einem Remote-Signal zu
und die angeschlossenen Verstärker voll aus- versorgen. Bitte verwenden Sie ausschließlich
gesteuert werden. Dies kann im Extremfall die dieses Signal zur Einschaltung der Verstärker,
Lautsprecher zerstören. um Ein- und Ausschaltgeräusche zu vermei-
Wir raten deshalb dringend dazu, eine optionale den.
Fernbedienung zur Einstellung der Lautstärke
der digitalen Signaleingänge zu verwenden!
Hinweis: Der HELIX DSP PRO kann nur un-
komprimierte, digitale Stereo PCM-Signale
mit einer Abtastrate zwischen 12 kHz und
96 kHz / 192 kHz verarbeiten. Dolby-codierte
5.1-Signale können genauso wenig verarbei-
tet werden wie komprimierte MP3-/WMA- oder
AAC-Datenformate.
Um die Installation des DSP PRO an ein Werks- für Zündplus und Dauerplus vertauscht sein.
oder Nachrüstradio deutlich zu vereinfachen, Der DSP sollte die Stromversorgung jedoch
kann das Gerät auch mit Hilfe des optional er- nicht über die Zündleitung beziehen, da es
hältlichen Easy Plug Kabels (EPC 5.2 - Art.‑Nr. sonst zu Störgeräuschen kommen kann. Aus
HZ45000) angeschlossen werden. Über dieses diesem Grund muss vor der endgültigen In-
Kabel wird der Prozessor sowohl mit Strom als betriebnahme die Zuordnung von Zündplus
auch mit den Lautsprechersignalen des Radios und Dauerplus an der roten und der blauen
versorgt. Zudem muss bei dieser Installation Leitung vom ISO-Stecker kommend, mit einem
kein Kabel des Werkssoundsystems durch- Voltmeter überprüft werden. Dauerplus ist die
trennt werden. Das Easy Plug Kabel unterstützt Leitung, an der auch bei ausgeschalteter Zün-
allerdings nur vier der acht Lautsprecherein- dung eine Spannung von 12V messbar ist.
gänge des HELIX DSP PRO. Im folgenden wird Verbinden Sie nach erfolgter Messung das rote
der Anschluss an das Werksradio beschrieben: Kabel, zum HELIX DSP PRO führend, mit dem
Dauerplus-Kabel (entweder das blaue Kabel
1. Nachdem das Radio mit Hilfe der entspre- mit Stecker oder das rote Kabel mit Stecker).
chenden Werkzeuge ausgebaut ist, trennen Sie Die Plusleitung des Kabelbaums ist in der Re-
den Fahrzeugkabelbaum vom Autoradio. Ver- gel mit max. 20A abgesichert.
binden Sie den Fahrzeugkabelbaum anschlie- Hinweis: Im Auslieferungszustand ist das rote
ßend mit der Kupplung des Easy Plug Kabels. Kabel vom ISO-Stecker bis zum DSP PRO
Je nach Fahrzeugtyp benötigen Sie hierfür schon verbunden, da diese Variante in den mei-
gegebenenfalls einen fahrzeugspezifischen sten Fällen zutrifft.
ISO-Adapter. Eine Liste aller Fahrzeuge und Sollten Sie sich bezüglich der Zuordnung
der eventuell benötigten Adapter finden Sie auf nicht sicher sein, fragen Sie Ihren Fach-
www.audiotec-fischer.com. händler.
2. Verbinden Sie die Stecker des Easy Plug Ka- Hinweis: MOST-Bus
bels mit dem Autoradio. Bei einigen Fahrzeugen kann es notwendig sein,
die Lichtleiterverbindung aus dem Original-Radio-
3. Verbinden Sie den Highlevel-Stecker (8-poliger anschlussstecker auszulösen und stattdessen in
Stecker) und den Stromversorgungsstecker den Radio-Stecker eines ISO-Adapters einzuste-
(4-poliger Stecker) mit den jeweiligen Eingän- cken. Hierfür ist extra eine Aussparung im ISO-
gen des DSP PRO. Es ist Ihnen überlassen, ob Adapter vorhanden. Dies ist zwingend bei allen
Sie den Highlevel-Stecker mit den Eingängen Fahrzeugen notwendig, die einen Lichtleiteran-
A-D oder E-H verbinden. schluss im Originalradiokabelbaum haben.
9
Anschluss an den Computer
Der HELIX DSP PRO kann mit Hilfe der DSP 2. Installieren Sie die Software auf ihrem Compu-
PC‑Tool Software frei konfiguriert werden. Die Soft- ter. Während der Installation wird automatisch
ware stellt alle Funktionen übersichtlich und bedie- auch der USB-Treiber für das Gerät installiert.
nerfreundlich zur Verfügung, so dass Sie diese in- 3. Nach der Installation können Sie den Prozessor
dividuell einstellen können. Dabei können alle zehn mit dem beiliegenden USB-Kabel an den Com-
DSP Kanäle separat eingestellt werden. puter anschließen. Verlängern Sie das Kabel
Bevor Sie den HELIX DSP PRO das erste Mal an auf keinen Fall mit einer passiven USB-Verlän-
einen Computer anschließen, gehen Sie auf unsere gerung, weil eine einwandfreie Kommunikation
Homepage und laden Sie sich die aktuellste Soft- zwischen dem HELIX DSP PRO und Ihrem PC
ware-Version herunter. Es ist ratsam, regelmäßig nicht sicher gestellt werden kann. Wenn Sie
nach Updates der Software zu schauen, damit das längere Distanzen zu überbrücken haben, ver-
Gerät immer auf dem aktuellsten Stand ist. wenden Sie bitte eine aktive USB-Verlängerung
Die Software sowie die dazugehörige Bedienungs- mit integriertem Repeater.
anleitung finden Sie auf www.audiotec-fischer.com. 4. Schalten Sie den HELIX DSP PRO ein und
Es wird dringend empfohlen die Bedienungsanlei- starten Sie die Software. Wenn die Betriebs-
tung der Software vor der ersten Benutzung durch- software des Prozessors nicht mehr aktuell ist,
zulesen, um Komplikationen und Fehler zu vermei- wird diese automatisch aktualisiert.
den. 5. Sie können nun den HELIX DSP PRO mit der
Wichtig: Stellen Sie sicher, dass der DSP PC-Tool Software frei konfigurieren.
HELIX DSP PRO bei der ersten Installation der
Software noch nicht an den PC angeschlossen ist. Achtung: Es wird dringend empfohlen, vor der er-
Verbinden Sie diesen erst, wenn die Software voll- sten Inbetriebnahme an die Vorverstärkerausgänge
ständig installiert ist! des HELIX DSP PRO noch keine Verstärker anzu-
schließen bis die grundlegenden Einstellungen im
Im folgenden Abschnitt nun die wichtigsten Schritte Prozessor vorgenommen wurden. Bei Missachtung
zum Anschluss und der ersten Inbetriebnahme: kann es zur Zerstörung der angeschlossenen Laut-
sprecher kommen. Gerade bei vollaktiven Syste-
1. Laden Sie die DSP PC-Tool Software unter men besteht diese Gefahr.
www.audiotec-fischer.com herunter.
10
HELIX Extension Card Slot (HEC Slot)
Der HELIX DSP PRO kann durch die Montage ei- Zur Montage einer HEC muss das Seitenblech des
ner HELIX Extension Card (HEC) um weitere Funk- DSP PRO demontiert und gegen das dem HEC bei-
tionen erweitert werden - beispielsweise um eine liegende Seitenblech ausgetauscht werden. Detail-
Bluetooth Audiostreaming Funktion, einem weiteren lierte Informationen zum Einbau finden Sie in der
optischen Digitaleingang oder einem optischen Di- Bedienungsanleitung der jeweiligen HELIX Exten-
gitalausgang. sion Card.
HELIX Extension
Card Slot
Eingänge..........................................................................8 x Cinch
8 x Hochpegel-Lautsprechereingang
1 x Optisch SPDIF-Format (12 - 96 kHz)
1 x Coax SPDIF-Format (12 - 192 kHz)
1 x Remote In
Eingangsempfindlichkeit...................................................Cinch 2 - 4 Volt - Standard 4 Volt
Hochpegel 5 - 10 Volt oder 10 - 20 Volt (ent-
spricht 6 - 100 Watt RMS - nicht max. Power) -
Standard 10 Volt
Ausgänge.........................................................................10 x Cinch
1 x Remote Out
Ausgangsspannung..........................................................6 Volt RMS
Frequenzbereich..............................................................10 Hz - 44.000 Hz
DSP Auflösung.................................................................64 Bit
DSP Rechenleistung........................................................295 MHz (1.2 Mrd. MAC Operationen/Sekunde)
DSP Typ...........................................................................Audio Signalprozessor
Signalwandler...................................................................A/D: Asahi Kasei
D/A: Analog Devices
Signal-/ Rauschabstand Digitaleingang...........................116 dB (A-bewertet)
Signal-/ Rauschabstand Analogeingang..........................108 dB (A-bewertet)
Klirrfaktor (THD+N) Digitaleingang...................................< 0,0006 %
Klirrfaktor (THD+N) Analogeingang..................................< 0,001 %
Intermodulationsverzerrungen Digitaleingang..................< 0,002 %
Intermodulationsverzerrungen Analogeingang.................< 0,006%
Übersprechen...................................................................> 90 dB bei 10 kHz
Betriebsspannung �����������������������������������������������������������9,6 - 18 Volt, kurzzeitige Spannungseinbrüche
(bis 5 Sek.) bis auf 6 Volt sind zulässig
Stromaufnahme................................................................450 mA
Zusätzliche Features........................................................Control Input, USB, Masseschalter, HEC Slot
Abmessungen (H x B x T)................................................40 x 177 x 150 mm
Garantiehinweis
Die Garantieleistung entspricht der gesetzlichen Technische Änderungen und Irrtümer vorbehalten!
Regelung. Von der Garantieleistung ausgeschlos- Für Schäden am Fahrzeug oder Gerätedefekte,
sen sind Defekte und Schäden, die durch Überla- hervorgerufen durch Bedienungsfehler des
stung oder unsachgemäße Behandlung entstanden Gerätes, können wir keine Haftung übernehmen.
sind. Eine Rücksendung kann nur nach vorheriger Alle HELIX Produkte sind sowohl mit einer
Absprache in der Originalverpackung, einer de- E-Kennzeichnung als auch einer CE-Kennzeich-
taillierten Fehlerbeschreibung und einem gültigen nung versehen. Damit sind die Geräte für den Be-
Kaufbeleg erfolgen. trieb in Fahrzeugen innerhalb der Europäischen
Union (EU) zertifiziert.
12
Congratulations!
Dear Customer,
Congratulations on your purchase of this high-qual We wish you many hours of enjoyment with your
ity HELIX product. new HELIX DSP PRO.
Yours,
With the HELIX DSP PRO, Audiotec Fischer is set-
AUDIOTEC FISCHER
ting new standards for digital signal processors.
General instructions
General installation instructions for HELIX General instruction for connecting the HELIX
components DSP PRO
To prevent damage to the unit and possible injury, The HELIX DSP PRO may only be installed in ve-
read this manual carefully and follow all installati- hicles which have a negative ground electrical sys-
on instructions. This product has been checked for tem. Any other system may cause damage to the
proper function prior to shipping and is guaranteed processor and the electrical system of the vehicle.
against manufacturing defects.
Use only the provided connectors or an Easy Plug
Before starting your installation, disconnect Cable for the connection of HELIX DSP PRO. The
the battery’s negative terminal to prevent use of other cables can result in damage of the
damage to the unit, fire and / or risk of injury. For amplifier, the head unit / radio or the connected
a proper performance and to ensure full warranty loudspeakers!
coverage, we strongly recommend to get this pro-
duct installed by an authorized HELIX dealer. Prior to installation, plan the wire routing to
avoid any possible damage to the wire harness.
Install your HELIX DSP PRO in a dry location with All cabling should be protected against possible
sufficient air circulation for proper cooling of the crushing or pinching hazards. Also avoid routing
equipment. The processor should be secured to cables close to potential noise sources such as
a solid mounting surface using proper mounting electric motors, high power accessories and other
hardware. Before mounting, carefully examine the vehicle harnesses.
area around and behind the proposed installati-
on location to insure that there are no electrical
cables or components, hydraulic brake lines or any
part of the fuel tank located behind the mounting
surface. Failure to do so may result in unpredictable
damage to these components and possible costly
repairs to the vehicle.
13
Connectors and control units
1 2 3 4 5 6 7
1 Line Input
RCA inputs for connecting pre-amplifier sig-
5
Clipping LED
This LED lights up red if one of the analog
nals inputs is overdriven
2 Coax Input 6
Highlevel Input
Electrical input for digital stereo signals
Highlevel speaker inputs for connecting a
(SPDIF format) factory radio or an aftermarket radio without
pre-amp / line outputs
3
Input Switch
Selector between „Coax Input“ and „Optical 7 Power Input
Input“ Connector for the DC power supply with an
additional remote in- and output. The remote
4 Optical Input output has to be used to switch on external
Optical input for digital stereo signals (SPDIF amplifiers
format)
8 9 10 11 12 13
15
Initial start-up and functions
10 Status LED
The Status LED indicates the current active DSP
setup. Green means that setup 1 is loaded, orange
means that setup 2 is loaded. A flashing red light
indicates that no setup is loaded.
In that case please load a new setup via the
DSP PC‑Tool software.
16
Installation
Channel assignment:
Channel A
Channel B
Channel C
Channel D
Channel E
Channel F
Channel G
Channel H
Fig. 1
Jumper below*
Channel G & H:
2 V 4 V*
Jumper above
Highlevel
5 V 10 V* 10 V 20 V
RCA / Cinch
2 V 4 V* 2V 4V Channel G & H:
250 mV 500 mV
30 Ohm Input impedance 4 kOhm
Fig. 2 Fig. 3
* Ex factory adjustment of HELIX DSP PRO 17
Installation
Connection of HELIX DSP PRO to the head unit tive channels is shown in the figure 1 on page
(radio): 17.
Please note: The settings of the trim potentio-
Caution: Carrying out the following steps will re- meters affects both the lowlevel inputs and the
quire special tools and technical knowledge. In or- highlevel inputs!
der to avoid connection mistakes and / or damage, The sensitivity range of the highlevel inputs can
ask your dealer for assistance if you have any ques be modified by inserting the jumper into the op-
tions and follow all instructions in this manual (see posite position (see figure 2 / page 17).
page 13). The sensitivity range of the two lowlevel inputs
It is recommended that this unit will be installed by G and H can be changed by inserting the other
an authorized HELIX dealer. jumper into the opposite position (see figure 3 /
page 17). Thus it is possible to connect even
1. Connecting the pre-amplifier inputs mobile devices with significantly lower output
Use the correct cable (RCA / cinch cable) to con- voltage (like smartphones) to the HELIX DSP
nect these inputs to the pre-amplifier / lowlevel / PRO.
cinch outputs of your car radio. Follow the subsequent steps if you like to per-
Each input can be assigned to any output using fectly adapt the processors input sensitivity to
the DSP PC-Tool software. The automatic turn- your audio source by using the internal trim po-
on circuit does not work when using the pre- tentiometers:
amplifier inputs. In this case the „Remote Input“ 1. Don‘t connect any amplifier to the outputs of
has to be connected to activate the HELIX DSP the processor during this setup.
PRO. 2. Adjust the volume of your radio to approx.
Important: It is strictly forbidden to use the 90 % of the max. volume and playback a
highlevel input and pre-amplifier inputs at the 1 kHz full scale test tone (0 dB) via CD
same time. This may cause severe damage to drive.
the pre-amplifier outputs of your car radio. 3. The adjustment will be easier when you
connect and adjust one input channel after
2. Connecting the highlevel speaker inputs the other.
The highlevel loudspeaker inputs can be con- 4. If the Clipping LED already lights up, you
nected directly to the loudspeaker outputs of have to reduce the input sensitivity via the
an OEM or aftermarket radio using appropriate respective trim potentiometer until the LED
cables (loudspeaker cables with 1mm² / AWG18 goes out.
max.). It is not mandatory to use all speaker in- If the pot is already set to right stop position
puts. then it will be necessary to change the sen-
Make sure that the polarity is correct. If one or sitivity range by repositioning the jumper
more connections have reversed polarity this (see figure 2 / page 17). Note that this will
may affect the performance of the processor. If only have an effect on the highlevel inputs!
this input is used the remote input has not to be 5. Increase the input sensitivity by turning the
used as the processor will automatically turn on respective pot counterclockwise until the
once a loudspeaker signal is received. LED lights up. Now turn the potentiometer
clockwise until the Clipping LED goes out
3. Adjustment of the input sensitivity again.
If you want to change the input sensitivity you 6. Repeat this process for each channel you
have to open the device at first. Remove the are using.
four Philipps head screws of the side panel (in-
put side) and pull out the bottom plate. Now you 4. Connecting a digital signal source
have access to the eight trim potentiometers If you have a signal source with optical or coa-
that allow adjusting each channel individually. xial digital output you can connect it to the pro-
The assignment of the trim pots to the respec- cessor using the appropriate input.
18
In standard configuration the HELIX DSP PRO 6. Connecting the remote input
automatically activates the used digital input if The remote input has to be connected to the
an digital audio signal is detected. This function radio remote output if the processor’s pre-am-
can be deactivated via the DSP PC‑Tool soft- plifier inputs are used as signal inputs. We do
ware. Alternatively you can manually activate not recommend controlling the remote input via
the digital input if you are using the optional re- the ignition switch to avoid pop noise during turn
mote control. on / off.
The automatic turn-on circuit does not work If the highlevel inputs are used this input does
when the digital input is used. Therefore it is not need to be connected as long as the car ra-
mandatory to connect the „Remote In“ at the dio has BTL output stages.
power input if none of the highlevel inputs are
used. 7. Connecting the remote output
Please note that it is possible to connect a sour- This output is used to supply remote signals to
ce to one of the digital inputs and the highlevel the external amplifier/s. Always use this remote
or the pre-amplifier at the same time. output signal to turn on the amplifiers in order to
Important: The signal of a digital audio source avoid on/off switching noises.
normally does not contain any information about
the volume level. Keep in mind that this will lead
to full level on the outputs of the HELIX DSP
PRO and your connected amplifiers. This may
cause severe damage to your speakers.
We strongly recommend to use an optional re-
mote control for adjusting the volume level of
the digital signal input!
Information: The HELIX DSP PRO can only
handle uncompressed digital stereo signals in
PCM format with a sample rate between 12 kHz
and 96 kHz / 192 kHz. Neither Dolby-coded
5.1 signals nor compressed MP3-/WMA- or
AAC‑audio formats will be accepted.
19
Installation with „Easy Plug cable“
To simplify installing to an OEM or aftermarket ra- Note - Cars equipped with MOST bus:
dio the HELIX DSP PRO can also be connected In cars equipped with MOST bus structure it is
using the optional Easy Plug Cable (EPC 5.2 - art.- mandatory to unplug the fiber-optic cable from the
no. HZ45000) which will supply the processor with original radio connector and insert it into the ISO
both power and loudspeaker signals of the radio. adaptor, which has a dedicated recess for this.
No factory wires or plugs need to be cut using this
connection method.
Connection to an OEM radio is detailed below:
20
Connection to a PC
It is possible to freely configure the HELIX DSP 3. After the software installation process is com-
PRO with our DSP PC-Tool software. The user in- pleted you can now connect the processor to
terface is designed for easy handling of all functions your PC using the provided USB cable. Don’t
and allows an individual adjustment of each of the extend the supplied cable by using any passive
10 channels. Prior to connecting the processor to USB extension cable. If you need to cover long
your PC, visit our website and download the latest er distances between your PC and the HELIX
version of the DSP PC‑Tool software. Check from DSP PRO then use an active USB repeater ca-
time to time for software updates. ble.
You will find the software and the respective user 4. Turn on the processor and then start the soft-
manual on www.audiotec-fischer.com. ware. If the firmware is not the latest version it
We strongly recommend to carefully read the user will automatically be updated.
manual before using the software for the first time in 5. You are now ready to configure the HELIX
order to avoid any complications and failures. DSP PRO according to your demands.
Important: Make sure that the processor is not con- Comprehensive operating instructions
nected to your computer before the software and for the software can be downloaded from
USB driver are installed! www.audiotec-fischer.com.
To install the software follow the next steps: Caution: We strongly recommend to not connect
any external amplifiers to the pre-amplifier outputs
1. Download the DSP PC-Tool software from the of HELIX DSP PRO before the basic configurati-
website www.audiotec-fischer.com on of the processor has been completed. Ignoring
2. Install the software on your computer. During this advice may result in damaging the connected
that process the required USB driver will be au- speakers, especially if you are running a fully active
tomatically installed as well. configuration.
21
HELIX Extension Card Slot (HEC Slot)
It is possible to extend the functionality of the HELIX to remove the side panel of the DSP PRO and re-
DSP PRO by inserting an optional HELIX Extension place it by a new side panel that comes with the
Card (HEC) - for example a Bluetooth Audio Strea- HEC. Any further mounting information will be found
ming module, an additional optical digital input or an in the instruction manual of the respective HELIX
optical digital output. Extension Card.
To install a HELIX Extension Card it is necessary
HELIX Extension
Card Slot
96 kHz sampling rate The HELIX DSP PRO will reactivate the Remote
The HELIX DSP PRO allows to handle all signal Output within a second if a music signal is applied.
management with the doubled sampling rate of It is possible to either modify the turn-off time of
96 kHz. Thus the audio bandwidth is no longer li- 60 sec. or completely deactivate the “Power Save
mited to usual values like 22 kHz but allows an ex- Mode” via the DSP PC-Tool software.
tended frequency response to more than 40 kHz.
Doubling the sampling rate requires significantly Start-/Stop capability
higher DSP power as the number of possible arith- The switched power supply of the HELIX DSP PRO
metic operations is halved. Only the implementation assures a constant internal supply voltage even if
of the latest DSP chip generation allows raising the the battery’s voltage drops to 6 Volts during engine
sampling rate to 96 kHz and adding new features crank.
plus additional channels at the same time.
Automatic Digital Signal Detection
Power Save Mode Switching from analog input to the digital input is
The Power Save Mode is incorporated in the bas done automatically as soon as a signal is detected
ic setup. It allows to significantly reduce the power on the optical input. This feature can be deactivated
consumption of the amplifiers that are connected to in the DSP PC-Tool software. Alternatively you can
the HELIX DSP PRO once there’s no input signal use an optional remote control for manual switching
present for more than 60 seconds. between analog and digital inputs.
Please note that in many up-to-date cars with “CAN”
or any other internal bus structures it may happen
that the radio remains “invisibly” turned on for up to
45 min. even after leaving the car!
Once the “Power Save Mode“ is active the Remote
Output and therefore the connected amplifiers will
be turned off.
22
Technical Data
Warranty Disclaimer
The limited warranty comply with legal regulations. For damages on the vehicle and the device, caused
Failures or damages caused by overload or improp by handling errors of the device, we can’t assume
er use are not covered by the warranty. liability.
Please return the defective product only with a All HELIX products are tagged with a E-Certifi-
valid proof of purchase and a detailed malfunction cation number and also a CE-Certification mark.
description. Thereby these devices are ceritified for a use
Technical specifications are subject to change! inside vehicles inside the European Union (EU).
Errors are reserved!
23
Audiotec Fischer GmbH
Gewerbegebiet Lake II · Hünegräben 26 · D-57392 Schmallenberg
Tel.: +49 2972 9788 0 · Fax: +49 2972 9788 88
E-mail: helix@audiotec-fischer.com · Internet: www.audiotec-fischer.com