Beruflich Dokumente
Kultur Dokumente
71 10/06/2020
Service
Chassis ID Path
B 466408 5618/Repair//Air drier, drier insert, replace
Model Identity
FH 127203366
Copyright to this documentation belongs to the Volvo Group. No reproduction, copying, change, amendment or other similar disposal is entitled without prior written consent by
the Volvo Group
The information contained herein is current at the time of its original distribution, but is subject to change. The reader is advised that printed copies are uncontrolled.
1/6
IMPACT 4.07.71 10/06/2020
Caution
Follow the instructions carefully to avoid personal injury and damage to the product or equipment.
2
Apply the parking brake.
Copyright to this documentation belongs to the Volvo Group. No reproduction, copying, change, amendment or other similar disposal is entitled without prior written consent by
the Volvo Group
The information contained herein is current at the time of its original distribution, but is subject to change. The reader is advised that printed copies are uncontrolled.
2/6
IMPACT 4.07.71 10/06/2020
A = 9998313
6
Copyright to this documentation belongs to the Volvo Group. No reproduction, copying, change, amendment or other similar disposal is entitled without prior written consent by
the Volvo Group
The information contained herein is current at the time of its original distribution, but is subject to change. The reader is advised that printed copies are uncontrolled.
3/6
IMPACT 4.07.71 10/06/2020
Check that the inlet in the middle from the drier insert to the drier housing is clean, otherwise the desiccant reservoir
has failed or the compressor's oil consumption is too high. Abnormal carbonization in the air drier requires an
inspection of the cooling coil. Refer to: 56176-2 Cooling coil, compressor, check and if necessary replacement.
Clean the drier housing internally.
Spread a thin layer of grease on the sealing surfaces and threads.
Copyright to this documentation belongs to the Volvo Group. No reproduction, copying, change, amendment or other similar disposal is entitled without prior written consent by
the Volvo Group
The information contained herein is current at the time of its original distribution, but is subject to change. The reader is advised that printed copies are uncontrolled.
4/6
IMPACT 4.07.71 10/06/2020
Screw in the new desiccant reservoir until it is against the housing. Tighten by hand another 1/2 turn. (approx. 20Nm).
Warning
When starting the engine with the cab tilted, make sure that the vehicle is not in gear and that the parking
brake is applied.
9
Start the engine. Run the brake pressure up until the compressor disengages. Turn off the engine.
Perform a leakage check with leakage detector instrument 88890086 or use Volvo leak finder spray.
10
Copyright to this documentation belongs to the Volvo Group. No reproduction, copying, change, amendment or other similar disposal is entitled without prior written consent by
the Volvo Group
The information contained herein is current at the time of its original distribution, but is subject to change. The reader is advised that printed copies are uncontrolled.
5/6
IMPACT 4.07.71 10/06/2020
11
Calibration is to be carried out when replacing desiccant reservoirs. Customers who do not wish to carry out calibration
when replacing desiccant reservoirs can shut off this function using VCADS-PRO. This removes the possibility of
reading off the remaining number of kilometers until the next desiccant reservoir replacement.
12
Connect the VCADS PC.
Reset the parameter for the desiccant reservoir.
Start calibration, wait until it is completed.
Close the test and disconnect VCADS PC.
Copyright to this documentation belongs to the Volvo Group. No reproduction, copying, change, amendment or other similar disposal is entitled without prior written consent by
the Volvo Group
The information contained herein is current at the time of its original distribution, but is subject to change. The reader is advised that printed copies are uncontrolled.
6/6