Beruflich Dokumente
Kultur Dokumente
GS 77J09A01-01E
n General
The WA1A/WA1V is a compact, front terminal connec-
tion type distributor that is used in combination with a
two-wire transmitter, and converts the transmitter’s 4
to 20 mA DC signals into isolated DC current or DC
voltage signals.
• Dual output and 2000 V AC withstand voltage specifi-
cations are available upon requests.
Allowable load resistance:
n Model and Suffix Codes
DC current Allowable load DC voltage Allowable load
WA1-A-*B/ output resistance output resistance
4 to 20 mA 750 Ω or less 0 to 10 mV 250 kΩ or more
Model
2 to 10 mA 1500 Ω or less 0 to 100 mV 250 kΩ or more
Output signal specification 1 to 5 mA 3000 Ω or less 0 to 1 V 2 kΩ or more
A : DC current signal 0 to 20 mA 750 Ω or less 0 to 10 V 10 kΩ or more
V : DC voltage signal 0 to 16 mA 900 Ω or less 0 to 5 V 2 kΩ or more
Input Signal 0 to 10 mA 1500 Ω or less 1 to 5 V 2 kΩ or more
A : 4 to 20 mA DC
0 to 1 mA 15 kΩ or less -10 to +10 V 10 kΩ or more
(Transmitter power supply: 26.5±1.5 V DC)
Output signal
[WA1A] [WA1V] n Standard Performance
A: 4 to 20 mA DC 1 : 0 to 10 mV DC Accuracy rating: ±0.1% of span
B: 2 to 10 mA DC 2 : 0 to 100 mV DC Accuracy is not guaranteed for output level
C: 1 to 5 mA DC 3 : 0 to 1 V DC less than 0.5% of the span of a 0 to X mA
D: 0 to 20 mA DC 4 : 0 to 10 V DC output range type.
E: 0 to 16 mA DC 5 : 0 to 5 V DC Dual output (optional): Relative error between
F: 0 to 10 mA DC 6 : 1 to 5 V DC output-1 and 2 is within ±0.2%. These
G: 0 to 1 mA DC 7 : -10 to +10 V DC
outputs are not insulated.
Z: (Custom order) 0 : (Custom order)
Current signal Voltage signal
Response speed: 200 ms, 63% response (10 to 90%)
(24 mA or less) (±10 V or less) Insulation resistance: 100 MΩ or more at 500 V DC
between input and output, output and
Power supply power supply, power supply and ground,
1 : 24 V DC±10% (DC drive) and ground and input.
2 : 85 to 264 V AC (AC drive) Withstand voltage:
Optional specification DC drive 1500 V AC/min. between input and (out-
D0 : Dual output (1 to 5 V DC) put and power supply).
500 V AC/min. between output and
power supply.
n Ordering Information AC drive 1500 V AC/min. between input and out-
Specify the following when ordering. put, output and power supply, power sup-
• Model and suffix codes :e.g. WA1V-A6-2*B ply and ground, and ground and input.
Span (DC) 1 to 24 mA 10 mV to 20 V
n Terminal Assignments
n Block Diagram
Combination with two-wire Combination with
transmitter using external two-wire transmitter
power supply using internal power
supply Transmitter power supply
L (+)
When using as an isolator 14
Power supply
N (–)
Transmitter 15
+ 7 Power supply
circuit GND
4 to 20 mA Use for AC power
- 16
8 supply only
n External Dimensions
48 4 - ø5×5.5 127
24.5 37 Unit: mm
Mounting hole
99
90
72
All Rights Reserved. Copyright © 2007, Yokogawa Electric Corporation GS 77J09A01-01E Aug. 01, 2007-00
Subject to change without notice.