Beruflich Dokumente
Kultur Dokumente
This equipment has been tested and found to comply with the limits of a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. There is no guarantee
that interference will not occur in a particular installation.
The content of this user’s manual is subject to be changed without notice and
we will not be responsible for any mistakes found in this user’s manual. All the
brand and product names are trademarks of their respective companies.
Table of Contents
CHAPTER 1: INTRODUCTION
1.1 BEFORE YOU START
Thank you for choosing our product. Before you start installing the
motherboard, please make sure you follow the instructions below:
Prepare a dry and stable working environment with
sufficient lighting.
Always disconnect the computer from power outlet
before operation.
Before you take the motherboard out from anti-static
bag, ground yourself properly by touching any safely
grounded appliance, or use grounded wrist strap to
remove the static charge.
Avoid touching the components on motherboard or the
rear side of the board unless necessary. Hold the board
on the edge, do not try to bend or flex the board.
Do not leave any unfastened small parts inside the
case after installation. Loose parts will cause short
circuits which may damage the equipment.
Keep the computer from dangerous area, such as heat
source, humid air and water.
Note: The package contents may differ by area or your motherboard version.
1
Motherboard Manual
AMD 780G
Chipset
AMD SB700
Main Max Memory Capacity 8GB Supports DDR2 533 / 667 / 800
Memory Each DIMM supports 256/512MB/1GB/2GB Supports DDR2 1066 (for AM2+ CPU only)
PCI Express Gen2 x16 slot x1 Supports PCI-E Gen2 x16 expansion cards
Slots PCI Express Gen2 x1 slot x1 Supports PCI-E Gen2 x1 expansion cards
2
TA780G M2+
SPEC
CPU Fan header x1 CPU Fan power supply (with Smart Fan function)
PS/2 LAN
Mouse Line In/
Surround
Line Out
Mic In 1/
Bass/ Center
3
Motherboard Manual
1.5 MOTHERBOARD LAYOUT
JCFAN1
JKBMS1
JATXPWR2
VGA
JATXPWR1
Socket
DVI
DIMMA1
DIMMB1
DIMMA2
DIMMB2
AM2+
JUSB1
JUSBV1
JUSBLAN1
JAUDIO1
IDE1
AMD
BAT TERY
JAUDIOF1 780G
JCDIN1 LAN
PEX1_1
PEX16_1
Codec
BIOS
JSFAN1
PCI1 AMD
SB700 SATA5 SATA6
JSPDIF_OUT1 JUSB4
Super I/O
SATA4
SATA3
PCI2
SATA1
JCOM1 JPRNT1 JUSB3 JUSB2 SATA2
JCMOS1
FDD1
JUSBV2
JPANEL1
4
TA780G M2+
CHAPTER 2: HARDWARE INSTALLATION
2.1 INSTALLING CENTRAL PROCESSING UNIT (CPU)
Step 2: Pull the lever toward direction A from the socket and then raise the
lever up to a 90-degree angle.
Step 3: Look for the white triangle on socket, and the gold triangle on
CPU should point towards this white triangle. The CPU will fit only
in the correct orientation.
5
Motherboard Manual
Step 4: Hold the CPU down firmly, and then close the lever toward direct
B to complete the installation.
Step 5: Put the CPU Fan on the CPU and buckle it. Connect the CPU
FAN power cable to the JCFAN1. This completes the installation.
Note: Please update the BIOS to the latest version while using AM2+ CPUs. Due to the latest CPU
transition, you may encounter the situation that the new system failed to boot while using new
AM2+ CPUs. In this case, please install one standard AM2 CPU to boot your system, and
update the latest BIOS from our website for AM2+ CPUs support.
6
TA780G M2+
1 Pin Assignment
1 Ground
2 +12V
3 FAN RPM rate
sense
4 Smart Fan
Control (By Fan)
Pin Assignment
1 Ground
2 +12V
3 FAN RPM rate
sense
1 3
Note:
The JCFAN1 supports 4-pin head connector. The JSFAN1 supports 3-pin head
connector. When connecting with wires onto connectors, please note that the red wire is
the positive and should be connected to pin#2, and the black wire is Ground and should
be connected to GND.
7
Motherboard Manual
2.3 INSTALLING SYSTEM MEMORY
A. Memory Modules
DIMMA1
DIMMB1
DIMMA2
1. DIMMB2
Unlock a DIMM slot by pressing the retaining clips outward. Align a
DIMM on the slot such that the notch on the DIMM matches the
break on the Slot.
2. Insert the DIMM vertically and firmly into the slot until the retaining
chip snap back in place and the DIMM is properly seated.
8
TA780G M2+
B. Memory Capacity
DIMM Socket Total Memory
DDR2 Module
Location Size
DIMMA1 256MB/512MB/1GB/2GB
DIMMB1 256MB/512MB/1GB/2GB
Max is 8GB.
DIMMA2 256MB/512MB/1GB/2GB
DIMMB2 256MB/512MB/1GB/2GB
Install memory module of the same density in pairs, shown in the following
table.
Dual Channel Status DIMMA1 DIMMB1 DIMMA2 DIMMB2
Enabled O O X X
Enabled X X O O
Enabled O O O O
(O means memory installed, X means memory not installed.)
The DRAM bus width of the memory module must be the same (x8 or
x16)
9
Motherboard Manual
2 34
1 33
40 39
2 1
10
TA780G M2+
PEX1_1
PEX16_1
PCI1
PCI2
11
Motherboard Manual
CHAPTER 3: HEADERS & JUMPERS SETUP
3.1 HOW TO SETUP JUMPERS
The illustration shows how to set up jumpers. When the jumper cap is
placed on pins, the jumper is “close”, if not, that means the jumper is
“open”.
12
TA780G M2+
JATXPWR1: ATX Power Source Connector
This connector allows user to connect 24-pin power connector on the ATX
power supply.
12 24
1 13
4 3
Pin Assignment
1 +12V
1 2 2 +12V
3 Ground
4 Ground
13
Motherboard Manual
Pin Assignment
1 +5V (fused)
2 +5V (fused)
3 USB-
4 USB-
5 USB+
JUSB4 6 USB+
JUSB3 JUSB2 7 Ground
8 Ground
2 10 9 NC
10 Key
1 9
Pin Assignment
1 Ground
2 TX+
SATA5 SATA6 3 TX-
4 Ground
SATA3 SATA4
5 RX-
SATA1 SATA2 6 RX+
7 Ground
7 4 1
14
TA780G M2+
Pin Assignment
1 +5V
2 SPDIF_OUT
3 Ground
1 3
Pin Assignment
1 Mic Left in
2 Ground
3 Mic Right in
4 GPIO
10 9 5 Right line in
6 Jack Sense
7 Front Sense
8 Key
2 1 9 Left line in
10 Jack Sense
15
Motherboard Manual
Pin Assignment
1 Left Channel
Input
1 2 Ground
3 Ground
4 Right Channel
4 Input
1 3
1 3
16
TA780G M2+
JPRNT1: Printer Port Connector
This header allows you to connector printer on the PC.
1 25
Pin Assignment
1 Carrier detect
2 Received data
3 Transmitted data
4 Data terminal ready
5 Signal ground
6 Data set ready
7 Request to send
2 10 8 Clear to send
9 Ring indicator
10 NC
1 9
17
Motherboard Manual
1
1 3
JUSBV1 3
1
Pin 1-2 close
3
1
1 3
1 3
3
Pin 2-3 close
JUSBV2
18
TA780G M2+
Block 1 Block 2
Block 3 Block 4
Block 5 Block 6
19
Motherboard Manual
RAID 1:
Every read and write is actually carried out in parallel across 2 disk drives in a RAID 1
array system. The mirrored (backup) copy of the data can reside on the same disk or on
a second redundant drive in the array. RAID 1 provides a hot-standby copy of data if
the active volume or drive is corrupted or becomes unavailable because of a hardware
failure.
RAID techniques can be applied for high-availability solutions, or as a form of
automatic backup that eliminates tedious manual backups to more expensive and less
reliable media.
Features and Benefits
- Drives: Minimum 2, and maximum is 2.
- Uses: RAID 1 is ideal for small databases or any other application that
requires fault tolerance and minimal capacity.
- Benefits: Provides 100% data redundancy. Should one drive fail, the
controller switches to the other drive.
- Drawbacks: Requires 2 drives for the storage space of one drive.
Performance is impaired during drive rebuilds.
- Fault Tolerance: Yes.
Block 1 Block 1
Block 2 Block 2
Block 3 Block 3
20
TA780G M2+
RAID 1+0:
RAID 1 drives can be stripped using RAID 0 techniques. Resulting in a RAID 1+0
solution for improved resiliency, performance and rebuild performance.
Features and Benefits
- Drives: Minimum 4, and maximum is 6 or 8, depending on the platform.
- Benefits: Optimizes for both fault tolerance and performance, allowing for
automatic redundancy. May be simultaneously used with other RAID
levels in an array, and allows for spare disks.
- Drawbacks: Requires twice the available disk space for data redundancy,
the same as RAID level 1.
- Fault Tolerance: Yes.
21
Motherboard Manual
!! WARNING !!
For better system performance, the BIOS firmware is being
continuously updated. The BIOS information described below in
this manual is for your reference only and the actual BIOS
information and settings on board may be different from this
manual. For further information of setting up the BIOS, please
refer to the BIOS Manual in the Setup CD.
ONE provides two powerful overclocking engines: MOS and AOS for both
Elite and Casual overclockers.
BIOS SETUP UTILITY
Main Advanced PCIPnP Boot Chipset T-Series Exit
22
TA780G M2+
↓
BIOS SETUP UTILITY
Main Advanced PCIPnP Boot Chipset T-Series Exit
CPU Overvoltage
This function will increase CPU stability when overclocking. However, the
CPU temperature will increase when CPU voltage is increased.
Memory Overvoltage
This function will increase memory stability when overclocking.
Chipset Overvoltage
This function will increase Northbridge and Southbridge chipset stability
when overclocking.
HT Overvoltage
This function will increase CPU stability when overclocking the HT ratio.
23
Motherboard Manual
CPU Frequency
CPU Frequency is directly in proportion to system performance. To
maintain the system stability, CPU voltage needs to be increased also
when raising CPU frequency.
Memory Configuration
Enter this function for more advanced memory settings.
DRAM Timing Configuration
Enter this function for more advanced DRAM clock settings.
Hyper Transport Configuration
Enter this function for more advanced Hyper Transport settings.
24
TA780G M2+
V6 Tech Engine
This engine will make a good over-clock performance.
BIOS SETUP UTILITY
Main Advanced PCIPnP Boot Chipset T-Series Exit
V8 Tech Engine
This engine will make a better over-clock performance.
BIOS SETUP UTILITY
Main Advanced PCIPnP Boot Chipset T-Series Exit
25
Motherboard Manual
Notices:
1. Not all types of AMD CPU perform above overclock setting ideally; the difference will be based
on the selected CPU model.
↓
BIOS SETUP UTILITY
Main Advanced PCIPnP Boot Chipset T-Series Exit
Step 2
Save and Exit from CMOS setup and reboot the system to activate this test.
Run this test for 5 minutes (minimum) to ensure the memory stability.
Step 3
When the process is done, change the setting back from “Enable” to “Disable”
to complete the test.
26
TA780G M2+
C. BIO-Flasher
BIO-Flasher is a BIOS flashing utility providing you an easy and simple way to
update your BIOS via USB pen drive or floppy disk.
The BIO-Flasher is built in the BIOS chip. To enter the utility, press <F12>
during the Power-On Self Tests (POST) procedure while booting up.
2. Then, save the BIOS file into a USB pen drive or a floppy disk.
3. Insert the USB pen drive or the floppy disk that contains the BIOS file to the
USB port or the floppy disk drive.
6. After the update process, the utility will ask you to reboot the system.
Press <Y> to proceed. BIOS update completes.
z This utility only allows storage device with FAT32/16 format and single
partition.
z Shutting down or resetting the system while updating the BIOS will lead to
system boot failure.
27
Motherboard Manual
D. Self Recovery System (S.R.S.)
This function can’t be seen under BIOS setup; and is always on whenever the
system starts up.
However, it can prevent system hang-up due to inappropriate overclock
actions.
When the system hangs up, S.R.S. will automatically log in the default BIOS
setting, and all overclock settings will be re-configured.
Select Screen
Select Item
+- Change Option
F1 General Help
F10 Save and Exit
ESC Exit
28
TA780G M2+
Smart Fan Calibration
Choose this item and then the BIOS will automatically test and detect the
CPU/System fan functions and show CPU/System fan speed.
Control Mode
This item provides several operation modes of the fan.
29
Motherboard Manual
Hardware Monitor
HW Monitor is a monitor utility that helps you to maintain the health of the PC.
It provides real-time information of CPU/GPU/System temperature, fan speed,
and voltage.
This area shows volt age information
Voltage Panel This area shows CPU inf ormation Fan Panel
30
TA780G M2+
eHot-Line (Optional)
eHot-Line is a convenient utility that helps you to contact with our
Tech-Support system. This utility will collect the system information which is
useful for analyzing the problem you may have encountered, and then send
these information to our tech-support department to help you fix the problem.
Before you use this utility, please set Outlook Express as your default e-mail client application program.
If you want to save this information to a .txt file, click “Save As…” and then you
will see a saving dialog appears asking you to enter file name.
31
Motherboard Manual
We will not share customer’s data with any other third parties,
so please feel free to provide your system information while using
eHot-Line service.
If you are not using Outlook Express as your default e-mail client
application, you may need to save the system information to a .txt file
and send the file to our tech support with other e-mail application.
Go to the following web
http://www.biostar.com.tw/app/en-us/about/contact.php for getting
our contact information.
32
TA780G M2+
CHAPTER 6: USEFUL HELP
6.1 DRIVER INSTALLATION NOTE
After you installed your operating system, please insert the Fully Setup
Driver CD into your optical drive and install the driver for better system
performance.
You will see the following window after you insert the CD
The setup guide will auto detect your motherboard and operating system.
Note:
If this window didn’t show up after you insert the Driver CD, please use file browser to
locate and execute the file SETUP.EXE under your optical drive.
A. Driver Installation
To install the driver, please click on the Driver icon. The setup guide will
list the compatible driver for your motherboard and operating system.
Click on each device driver to launch the installation program.
B. Software Installation
To install the software, please click on the Software icon. The setup guide
will list the software available for your system, click on each software title
to launch the installation program.
C. Manual
Aside from the paperback manual, we also provide manual in the Driver
CD. Click on the Manual icon to browse for available manual.
Note:
You will need Acrobat Reader to open the manual file. Please download the latest version
of Acrobat Reader software from
http://www.adobe.com/products/acrobat/readstep2.html
33
Motherboard Manual
6.2 AMI BIOS BEEP CODE
Beep Sound Meaning
One short beep VGA detected
Quick boot set to disabled
No keyboard detected
One long beep followed by two short No memory detected
beeps then a pause
One long beep followed by three short No VGA detected
beeps
One long beep followed by four short Hardware component failure
beeps
After confirmed, please follow steps below to relief the CPU protection
function.
1. Remove the power cord from power supply for seconds.
2. Wait for seconds.
3. Plug in the power cord and boot up the system.
Or you can:
1. Clear the CMOS data.
(See “Close CMOS Header: JCMOS1” section)
2. Wait for seconds.
3. Power on the system again.
34
TA780G M2+
6.4 TROUBLESHOOTING
Probable Solution
1. No power to the system at all 1. Make sure power cable is
Power light don’t illuminate, fan securely plugged in.
inside power supply does not turn 2. Replace cable.
on. 3. Contact technical support.
2. Indicator light on keyboard does
not turn on.
System inoperative. Keyboard lights Using even pressure on both ends of
are on, power indicator lights are lit, the DIMM, press down firmly until the
and hard drive is spinning. module snaps into place.
System does not boot from hard disk 1. Check cable running from disk to
drive, can be booted from optical drive. disk controller board. Make sure
both ends are securely plugged
in; check the drive type in the
standard CMOS setup.
2. Backing up the hard drive is
extremely important. All hard
disks are capable of breaking
down at any time.
System only boots from optical drive. 1. Back up data and applications
Hard disk can be read and applications files.
can be used but booting from hard disk 2. Reformat the hard drive.
is impossible. Re-install applications and data
using backup disks.
Screen message says “Invalid Review system’s equipment. Make sure
Configuration” or “CMOS Failure.” correct information is in setup.
Cannot boot system after installing 1. Set master/slave jumpers
second hard drive. correctly.
2. Run SETUP program and select
correct drive types. Call the drive
manufacturers for compatibility
with other drives.
35
Motherboard Manual
APPENDENCIES: SPEC IN OTHER LANGUAGE
GERMAN
Spezifikationen
Sockel AM2+ / AM2 Die AMD 64-Architektur unterstützt eine 32-Bit- und
AMD 780G
Chipsatz
AMD SB700
HD
5.1-Kanal-Audioausgabe
Audio-Unters ALC662
Unterstützt High-Definition Audio
tützung
PCI-Steckplatz x2
36
TA780G M2+
Spezifikationen
"CMOS löschen"-Sockel x1
Stromanschluss (24-polig) x1
Stromanschluss (4-polig) x1
Serieller Anschluss x1
PS/2-Tastatur x1
PS/2-Maus x1
VGA-Anschluss x1
Rückseiten-E
LAN-Anschluss x1
/A
USB-Anschluss x4
Audioanschluss x3
DVI-Anschluss x1
Platinengröß
215 mm (B) X 244 mm (L)
e
37
Motherboard Manual
FRANCE
SPEC
Socket AM2+ / AM2
L'architecture AMD 64 permet le calcul 32 et 64 bits
UC Processeurs AMD Athlon 64 / Athlon 64 FX
Prend en charge Hyper Transport 3.0 et Cool’n’Quiet
/ Althlon 64 X2 / Sempron / Phenom
Prend en charge Hyper Transport 3.0
Bus frontal
jusqu'à une bande passante de 5.2 GT/s
AMD 780G
Chipset
AMD SB700
Interface à faible compte de broches
ITE 8718F
Initiatives de contrôle environnementales,
Super E/S Fournit la fonctionnalité de Super E/S
Moniteur de matériel
patrimoniales la plus utilisée.
Fonction "Gardien intelligent" de l'ITE
Module de mémoire DDR2 à mode à double voie
Fentes DDR2 DIMM x 4
Prend en charge la DDR2 533 / 667 / 800
Mémoire Capacité mémoire maximale de 8 Go
Prend en charge la DDR2 1066 (for AM2+ CPU only)
principale Chaque DIMM prend en charge des DDR2
Les DIMM à registres et DIMM avec code correcteurs
de 256/512 Mo et 1Go/2Go
d'erreurs ne sont pas prises en charge
Mémoire vidéo partagée maximale de 512 Mo
Graphiques Integré dans la chipset AMD 780G Prise en charge DX10
Prise en charge HDCP / UVD
Mode principale de Bus Ultra DMA 33 / 66 / 100 / 133
IDE Contrôleur IDE intégré
Prend en charge le mode PIO 0~4,
Taux de transfert jusqu'à 3 Go/s.
SATA Contrôleur Serial ATA intégré
Conforme à la spécification SATA Version 2.0
10 / 100 /1000 Mb/s négociation automatique
LAN Realtek RTL 8111C
Half / Full duplex capability
Prise en
Sortie audio à 5.1 voies
charge ALC662
Prise en charge de l'audio haute définition
audio HD
Fente PCI Express Gen2 x16 x1
Fentes Fente PCI Express Gen2 x1 x1
Fente PCI x2
Connecteur Chaque connector prend en charge 2 lecteurs de
Connecteur de disquette x1
embarqué disquettes
Chaque connecteur prend en charge 2 périphériques
Connecteur IDE x1
IDE
Chaque connecteur prend en charge 1 périphérique
Connecteur SATA x6
SATA
38
TA780G M2+
SPEC
Connecteur du panneau avant x1 Prend en charge les équipements du panneau avant
Connecteur Audio du panneau avant x1 Prend en charge la fonction audio du panneau avant
Connecteur d'entrée CD x1 Prend en charge la fonction d'entrée audio de CD
Connecteur de sortie S/PDIF x1 Prend en charge la fonction de sortie audio numérique
Alimentation électrique du ventilateur UC (avec
Embase de ventilateur UC x1
fonction de ventilateur intelligent)
Embase de ventilateur système x1 Alimentation électrique du ventilateur système
Embase d'effacement CMOS x1
Chaque connecteur prend en charge 2 ports USB de
Connecteur USB x3
panneau avant
Connecteur d'alimentation x1
(24 broches)
Connecteur d'alimentation x1
(4 broches)
Chaque connector prend en charge 1 Port
Connecteur de Port d'imprimante x1
d'imprimante
Connecteur de Port série x1
Clavier PS/2 x1
Souris PS/2 x1
E/S du Port VGA x1
panneau Port LAN x1
arrière Port USB x4
Fiche audio x3
Port DVI x1
Dimension
s de la 215 mm (l) X 244 mm (H)
carte
Fonctionnal
Prise en charge RAID 0 / 1 / 1+0
ités
Prise en charge HyperFlash
spéciales
Biostar se réserve le droit d'ajouter ou de supprimer le
Support SE Windows XP / VISTA
support de SE avec ou sans préavis.
39
Motherboard Manual
ITALIAN
SPECIFICA
AMD 780G
Chipset
AMD SB700
Memoria Capacità massima della memoria 8GB Supporto di DDR2 533 / 667 / 800
principale Ciascun DIMM supporta DDR2 Supporto di DDR2 1066 (for AM2+ CPU only)
40
TA780G M2+
SPECIFICA
Connettore alimentazione x1
(24 pin)
Connettore alimentazione x1
(4 pin)
Tastiera PS/2 x1
Mouse PS/2 x1
Connettore audio x3
Porta DVI x1
i scheda (altezza)
Caratterist
Supporto RAID 0 / 1 / 1+0
iche
Supporto HyperFlash
speciali
41
Motherboard Manual
SPANISH
Especificación
Conectores Conector disco flexible X1 Cada conector soporta 2 unidades de disco flexible
42
TA780G M2+
Especificación
Conector de alimentación X1
(24 patillas)
Conector de alimentación X1
(4 patillas)
Teclado PS/2 X1
Ratón PS/2 X1
Conector de sonido X3
Puerto DVI X1
Tamaño de
215 mm. (A) X 244 Mm. (H)
la placa
Soporte de
Biostar se reserva el derecho de añadir o retirar el
sistema Windows XP / VISTA
soporte de cualquier SO con o sin aviso previo.
operativo
43
Motherboard Manual
PORTUGUESE
ESPECIFICAÇÕES
A arquitectura AMD 64 permite uma computação de
Socket AM2+ / AM2
32 e 64 bits
CPU Processadores AMD Athlon 64 / Athlon 64
Suporta as tecnologias Hyper Transport 3.0 e
FX / Althlon 64 X2 / Sempron / Phenom
Cool’n’Quiet
Suporta a tecnologia HyperTransport 3.0
FSB
com uma largura de banda até 5.2 GT/s
AMD 780G
Chipset
AMD SB700
ITE 8718F Interface LPC (Low Pin Count).
Especificaç
Proporciona as funcionalidades mais Iniciativas para controlo do ambiente
ão Super
utilizadas em termos da especificação Monitorização do hardware
I/O
Super I/O. Função "Smart Guardian" da ITE
Ranhuras DIMM DDR2 x 4 Módulo de memória DDR2 de canal duplo
Capacidade máxima de memória: 8 GB Suporta módulos DDR2 533 / 667 / 800
Memória
Cada módulo DIMM suporta uma Suporta módulos DDR2 1066 (for AM2+ CPU only)
principal
memória DDR2 de 256/512 MB & 1 GB/2 Os módulos DIMM registados e os DIMM ECC não são
GB suportados
Memória de vídeo máxima partilhada: 512 MB
Placa
Integrada no chipset AMD 780G Suporta as funções DX10
gráfica
Suporta as funções HDCP / UVD
Modo Bus master Ultra DMA 33 / 66 / 100 / 133
IDE Controlador IDE integrado
Suporta o modo PIO 0~4,
Velocidades de transmissão de dados até 3 Gb/s.
SATA Controlador Serial ATA integrado
Compatibilidade com a especificação SATA versão 2.0.
Auto negociação de 10 / 100 / 1000 Mb/s
LAN Realtek RTL 8111C
Capacidade semi/full-duplex
Suporte
para áudio Saída de áudio de 5.1 canais
ALC662
de alta Suporta a especificação High-Definition Audio
definição
Ranhura PCI Express Gen2 x16 x1
Ranhuras Ranhura PCI Express Gen2 x1 x1
Ranhura PCI x2
Conectores Conector da unidade de disquetes x1 Cada conector suporta 2 unidades de disquetes
na placa Conector IDE x1 Cada conector suporta 2 dispositivos IDE
Conector SATA x6 Cada conector suporta 1 dispositivo SATA
Conector do painel frontal x1 Para suporte de várias funções no painel frontal
44
TA780G M2+
ESPECIFICAÇÕES
Conector de áudio frontal x1 Suporta a função de áudio no painel frontal
Conector para entrada de CDs x1 Suporta a entrada de áudio a partir de CDs
Conector de saída S/PDIF x1 Suporta a saída de áudio digital
Alimentação da ventoinha da CPU (com a função
Conector da ventoinha da CPU x1
Smart Fan)
Conector da ventoinha do sistema x1 Alimentação da ventoinha do sistema
Conector para limpeza do CMOS x1
Conector USB x3 Cada conector suporta 2 portas USB no painel frontal
Conector de alimentação x1
(24 pinos)
Conector de alimentação x1
(4 pinos)
Conector da para impressora x1 Cada conector suporta 1 Porta para impressora
Conector da Porta série x1
Teclado PS/2 x1
Rato PS/2 x1
Entradas/S
Porta VGA x1
aídas no
Porta LAN x1
painel
Porta USB x4
traseiro
Tomada de áudio x3
Porta DVI x1
Tamanho
215 mm (L) X 244 mm (A)
da placa
Característi
Suporta as funções RAID 0 / 1 / 1+0
cas
Suporta as funções HyperFlash
especiais
Sistemas A Biostar reserva-se o direito de adicionar ou remover
operativos Windows XP / VISTA suporte para qualquer sistema operativo com ou sem
suportados aviso prévio.
45
Motherboard Manual
POLISH
SPEC
AMD 780G
Chipset
AMD SB700
Pamięć Maks. wielkość pamięci 8GB Obsługa DDR2 533 / 667 / 800
główna Każde gniazdo DIMM obsługuje moduły Obsługa DDR2 1066 (for AM2+ CPU only)
256/512MB oraz 1GB/2GB DDR2 Brak obsługi Registered DIMM oraz ECC DIMM
512 MB
Grafika Zintegrowana w chipsecie AMD 780G
Obsługa DX10
46
TA780G M2+
SPEC
Klawiatura PS/2 x1
Mysz PS/2 x1
Port VGA x1
Back Panel
Port LAN x1
I/O
Port USB x4
Gniazdo audio x3
Port DVI x1
Wymiary
215 mm (S) X 244 mm (W)
płyty
Obsluga
Biostar zastrzega sobie prawo dodawania lub
systemu
Windows XP / VISTA odwoływania obsługi dowolnego systemu
operacyjne
operacyjnego bez powiadomienia.
go
47
Motherboard Manual
RUSSIAN
СПЕЦ
CPU
(централь Гнездо AM2+ / AM2 Архитектура AMD 64 разрешать обработка данных
ный Процессоры AMD Athlon 64 / Athlon 64 на 32 и 64 бит
процессор FX / Althlon 64 X2 / Sempron / Phenom Поддержка Hyper Transport 3.0 и Cool’n’Quiet
)
Поддержка HyperTransport 3.0 с
FSB
пропускной способностью до 5.2 GT/s
Набор AMD 780G
микросхем AMD SB700
Модуль памяти с двухканальным режимом DDR2
Слоты DDR2 DIMM x 4
Поддержка DDR2 533 / 667 / 800
Основная Максимальная ёмкость памяти 8 ГБ
Поддержка DDR2 1066 (for AM2+ CPU only)
память Каждый модуль DIMM поддерживает
Не поддерживает зарегистрированные модули
256/512МБ & 1ГБ/2ГБ DDR2
DIMM and ECC DIMM
Интерфейс с низким количеством выводов
ITE 8718F
Инициативы по охране окружающей среды,
Обеспечивает наиболее используемые
Super I/O Аппаратный монитор
действующие функциональные
Функция ITE "Smart Guardian" (Интеллектуальная
возможности Super I/O.
защита)
Максимальная совместно используемая видео
Встроенная в набор микросхем AMD память составляет 512 МБ
Графика
780G Поддержка DX10
Поддержка HDCP / UVD
Встроенное устройство управления Режим "хозяина" шины Ultra DMA 33 / 66 / 100 / 133
IDE
встроенными интерфейсами устройств Поддержка режима PIO 0~4,
Встроенное последовательное скорость передачи данных до 3 гигабит/с.
SATA
устройство управления ATA Соответствие спецификации SATA версия 2.0.
Локальная Автоматическое согласование 10 / 100 / 1000 Мб/с
Realtek RTL 8111C
сеть Частичная / полная дуплексная способность
Звуковая
поддержка Звуковая поддержка High-Definition
ALC662
жесткого 5.1канальный звуковой выход
диска
Слот PCI Express Gen2 x16 x1
Слоты Слот PCI Express Gen2 x1 x1
Слот PCI x2
Встроенны Каждый разъём поддерживает 2 накопителя на
Разъём НГМД x1
й разъём гибких магнитных дисках
Каждый разъём поддерживает 2 встроенных
Разъём IDE x1
интерфейса накопителей
48
TA780G M2+
СПЕЦ
Разъём SATA x6 Каждый разъём поддерживает 1 устройство SATA
Разъём на лицевой панели x1 Поддержка устройств на лицевой панели
Входной звуковой разъём x1 Поддержка звуковых функций на лицевой панели
Разъём ввода для CD x1 Поддержка функции ввода для CD
Разъём вывода для S/PDIF x1 Поддержка вывода цифровой звуковой функции
Контактирующее приспособление Источник питания для вентилятора центрального
вентилятора центрального процессора (с функцией интеллектуального
процессора x1 вентилятора)
Контактирующее приспособление
Источник питания для вентилятора системы
вентилятора системы x1
Открытое контактирующее
приспособление CMOS x1
Каждый разъём поддерживает 2 USB-порта на
USB-разъём x3
лицевой панели
Разъем питания (24 вывод) x1
Разъем питания (4 вывод) x1
Разъём Порт подключения Каждый разъём поддерживает 1 Порт подключения
принтера x1 принтера
Разъём Последовательный порт x1
Клавиатура PS/2 x1
Мышь PS/2 x1
Задняя
Порт VGA x1
панель
Порт LAN x1
средств
USB-порт x4
ввода-выв
Гнездо для подключения
ода
наушников x3
Порт DVI x1
Размер
215 мм (Ш) X 244 мм (В)
панели
Специальн
ые
техническ Поддержка RAID 0 / 1 / 1+0
ие Поддержка HyperFlash
характери
стики
Biostar сохраняет за собой право добавлять или
Поддержк
Windows XP / VISTA удалять средства обеспечения для OS с или без
а OS
предварительного уведомления.
49
Motherboard Manual
ARABIC
اﻟﻤﻮاﺻﻔﺎت
AM2+ / AM2ﻡﻘﺒﺲ
إﺟﺮاء اﻟﻌﻤﻠﻴﺎت اﻟﺤﺎﺳﻮﺑﻴﺔ ﺑﺴﺮﻋﺔ 32و 64ﺑﺖAMD 64ﺗﻤﻜﻦ ﺗﻘﻨﻴﺔ وﺡﺪة اﻟﻤﻌﺎﻟﺠﺔ
AMD Athlon 64 / Athlon 64 FX / Sempron /ﻡﻌﺎﻟﺠﺎت
Cool’n’Quietو Hyper Transport 3.0ﺗﺪﻋﻢ ﺗﻘﻨﻴﺔ اﻟﻤﺮآﺰیﺔ
Phenom / Althlon 64 X2
AMD 780G
ﻡﺠﻤﻮﻋﺔ اﻟﺸﺮاﺋﺢ
AMD SB700
50
TA780G M2+
اﻟﻤﻮاﺻﻔﺎت
51
Motherboard Manual
JAPANESE
仕様
AMD 64アーキテクチャでは、32ビットと64ビット計算が可
Socket AM2+ / AM2
能です
CPU AMD Athlon 64 / Athlon 64 FX / Althlon 64
ハイパートランスポート3.0とクールアンドクワイアットを
X2 / Sempron / Phenom プロセッサ
サポートします
5.2 GT/sのバンド幅までハイパートランスポ
FSB
ート3.0をサポートします
ト AMD SB700
リ 各DIMMは 256/512MB & 1GB/2GB DDR2 DDR2 1066 をサポート (for AM2+ CPU only)
低ピンカウントインターフェイス
ITE 8718F
環境コントロールイニシアチブ、
Super I/O もっとも一般に使用されるレガシーSuper I/O
H/Wモニター
機能を採用しています。
ITEの「スマートガーディアン」機能
最大の共有ビデオメモリは512MBです
グラフィッ
AMD 780Gチップセットに統合 DX10 のサポート
クス
HDCP / UVD のサポート
最高3Gb/秒のデータ転送速度
SATA 統合シリアルATAコントローラ
SATAバージョン2.0仕様に準拠。
HDオーディ
5.1チャンネルオーディオアウト
オのサポー ALC662
ハイデフィニションオーディオのサポート
ト
PCIスロット x2
SATAコネクタ x6 各コネクタは1つのSATAデバイスをサポートします
52
TA780G M2+
仕様
フロントパネルコネクタ x1 フロントパネル機能をサポートします
フロントオーディオコネクタ x1 フロントパネルオーディオ機能をサポートします
CDインコネクタ x1 CDオーディオイン機能をサポートします
S/PDIFアウトコネクタ x1 デジタルオーディオアウト機能をサポートします
CPUファンヘッダ x1 CPUファン電源装置(スマートファン機能を搭載)
システムファンヘッダ x1 システムファン電源装置
CMOSクリアヘッダ x1
各コネクタは2つのフロントパネルUSBポートをサポートし
USBコネクタ x3
ます
電源コネクタ(24ピン) x1
電源コネクタ(4ピン) x1
プリンタポートコネクタ x1 各コネクタは1つのプリンタポートをサポートします
シリアルポートコネクタ x1
PS/2キーボード x1
PS/2マウス x1
VGAポート x1
背面パネル
LANポート x1
I/O
USBポート x4
オーディオジャック x3
DVIポート x1
ボードサイ
215 mm (幅) X 244 mm (高さ)
ズ
Biostarは事前のサポートなしにOSサポートを追加または削
OSサポート Windows XP / VISTA
除する権利を留保します。
2008/01/15
53