Beruflich Dokumente
Kultur Dokumente
In-Line Balanced
Pressure Proportioners
Models CIBP, CIBP-M
Features
n Six standard sizes to handle a wide range of flows with
minimal friction loss
n Spool valve design ensures accurate pressure regulation and
rapid response to changes in flow demand
n Brass foam concentrate piping with stainless steel trim acces-
sories standard for use in marine applications and other corro- 009829
sive environments
n Compatible with all CHEMGUARD foam concentrates The foam concentrate then enters the proportioner, where a
n Choice of unpainted brass or standard red paint finish built-in orifice regulates the flow of pressurized foam concentrate
entering the water stream.
The units are available in six standard sizes to supply proportion-
Application ers ranging from 2 in. to 8 in. with flow rates from 30 gpm to
CHEMGUARD In-Line Balanced Pressure Proportioners are 5,500 gpm (114 Lpm to 20,820 Lpm) as listed under the System
used with an atmospheric foam concentrate tank and a positive Information Table. Each unit consists of a foam proportioner,
displacement foam concentrate pump. In-line balanced pressure pressure balancing spool valve, duplex gauge, various control
proportioners are designed to accurately control the flow of a valves, drain valves, check valves, interconnecting brass pipe
foam liquid concentrate into a water stream over a wide range and fittings, stainless steel braid flexible pressure sensing hoses,
of flow rates and pressures. Advantages of the in-line balanced and valve identification nameplates. The CIBP-M models are
pressure proportioner include the following: also provided with a manual foam balancing valve. The in-line
n Multiple proportioning devices can be used with a single pres- balanced pressure proportioner is factory pressure tested after
surized foam concentrate supply. being assembled.
n Foam concentrate can be proportioned near the discharge
devices while the foam concentrate storage tank and pump are
placed in a remote location. Approvals
n Water supply pressure can vary at proportioners under simulta- The CHEMGUARD CIBP in-line proportioner is UL Listed with
neous operation without affecting foam solution concentration. various CHEMGUARD foam concentrates. For specific concen-
n Various sizes of in-line balanced pressure proportioners can be trates and corresponding flow ranges, consult Tyco Fire Protection
combined in a single system to best suit the flow requirements Products Technical Services.
of each hazard area.
Specifications
Description The in-line balanced pressure proportioner assembly shall
contain all necessary components including: foam proportioner,
The in-line balanced pressure proportioning system functions by
pressure balancing spool valve, duplex gauge, control valves,
maintaining an equal pressure in the foam concentrate and water
drain valves, check valves, interconnecting brass pipe, and valve
inlets to the proportioner. This balancing ability allows the propor-
identification nameplates.
tioner to be used over a wide range of flows and pressures. The
system will also respond quickly and accurately to changes in the Balancing shall be accomplished through the use of a spool-type
water inlet pressures and flow rates. pressure balancing valve. This valve shall sense foam concentrate
and water inlet pressures at the outer ends of a dumbbell-shaped
The system utilizes a positive displacement foam pump to pres- piston, and shall react to pressure changes by covering or uncov-
surize foam concentrate within the supply manifold. A pressure ering the foam supply port to the proportioner. The balancing
control valve, located in the return line that leads to the foam valve shall be low zinc (less than 15%) brass construction with a
concentrate storage tank, is set to maintain a regulated pres- bronze piston and Buna-N rubber O-rings and seals. The in-line
sure in the supply manifold that is higher than the pressure in balanced pressure proportioner shall be completely pressure
the water supply line. The foam concentrate that is not required tested by the manufacturer.
by the proportioner is returned to the atmospheric storage tank
through the pressure control valve. The spool valve senses the Interconnecting foam concentrate piping shall be of brass
foam concentrate pressure and automatically adjusts to balance construction. Pressure sensing hoses shall be TEFLON1 material
it with the water pressure. with a stainless braid cover and permanently attached brass
couplings. Valve nameplates shall be provided, and shall specify
A duplex pressure gauge provides a reading of the foam concen- valve function and normal operating position. The ‘‘foam
trate and water pressures. concentrate’’ ball valve shall have a ring pin and chain for
securing the ball valve in the operating position.
C
E D
G G
B 001172
Manual foam
balancing valve
G
F C
E H
H
B
A
*Between flange proportioner is standard. Upon request, proportioners can also be supplied in flanged style. 001173
Note: In-line balanced pressure proportioners require a minimum of 5 pipe diameters of straight, unobstructed water inlet supply pipe.
Ordering Information
Part No. Approximate Foam Solution
Water
Part No. Standard Shipping Weight Sensing Line
Discharge
Unpainted Red Paint Description lb (kg)
Spool Valve Proportioner
702500 702506 Model CIBP-2 In-line 45 (20.4)
Proportioner Assembly Foam Concentrate
702501 702507 Model CIBP-2 1/2 In-line 45 (20.4) Sensing Line
Spool Valve
In-Line
Foam Balanced
Return Line Pressure
Pressure
Control Valve Proportioner
Water
Supply
Automatic
Concentrate
Control Valve
Foam Suction
Line
Compound
Pressure
Gauge
Foam Pump and
Driver Assembly Foam Concentrate
001175
Supply
NOTE: Flush connections are only required with protein based foam concentrates.
LEGEND:
(2.1) 30
(1.7) 25
(1.4) 20
(1.0) 15
( 0.69) 10
(0.62) 9
Pressure Loss
(0.55) 8
(0.48) 7
(0.41) 6
(0.34) 5
(0.28) 4
(0.21) 3
(0.17) 2.5
(0.14) 2
(0.10) 1.5
(0.07) 1
50 100 200 300 500 700 1000 2000 3000 5000 8000 gpm
(189) (379) (757) (1136) (1893) (2650) (3785) (7571) (11356) (18927) (30283) (Lpm)
FLOW RATE 001176
(13.8) 200
(10.3) 150
(6.9) 100
Water Inlet Pressure
(3.4) 50
(2.8) 40
(2.1) 30
(1.4) 20
100 200 300 500 700 1000 2000 3000 5000 gpm
(379) (757) (1136) (1893) (2650) (3785) (7571) (11356) (18927) (Lpm)
WATER FLOW 001177