Beruflich Dokumente
Kultur Dokumente
SERVICE MANUAL
ATTENTION:
WARRANTY SERVICE PROCEDURES
Fender Musical Instruments Corp. / 17600 North Perimeter Drive, Suite 100 / Scottsdale, AZ 85255-5440
Issued June, 2016
2
BASSBREAKER™ 15
(This is the model name for warranty claims)
IMPORTANT NOTICE
Copyright © 2016 FMIC. All rights reserved. All specifications are subject to change without no-
information contained herein is CONFIDENTIAL tice. This information and any copies produced
and PROPRIETARY and is the property of Fender electronically or otherwise must be surrendered
Musical Instruments Corporation. It is not to be upon demand of Fender Musical Instruments Cor-
sold or assigned to another party and is disclosed poration.
solely for use by Fender® Authorized Service
Centers for purposes of product service and Parts marked with the “⚠” symbol indicate the re-
maintenance. All information is not to be dis- quired use of that specific part. This is necessary
closed to others without the expressed permission for RELIABILITY and SAFETY requirements.
of Fender Musical Instruments Corporation. All DO NOT USE A SUBSTITUTE!
BASSBREAKER™ 15
(This is the model name for warranty claims)
SPECIFICATIONS
Model Name: BASSBREAKER 15 Combo
BASSBREAKER 15 Head
BASSBREAKER™ 15
(This is the model name for warranty claims)
BASSBREAKER™ 15
(This is the model name for warranty claims)
SERVICE NOTES
As modern day amplifiers are more compact Rear Panel. Remove the two EFX Loop Jack Nuts
and sophisticated proper wire dress becomes a and Washers from the rear panel noting their
critical issue, both for the sake of Safety and makeup for reassembly. Remove the six (6) PCB
FCC Certification. It is highly recommended that Mounting standoff screws from the PCB and sepa-
before disassembly you take digital photos to rate the PCB from the Rear Panel.
use as a reference during reassembly, for wire
and component dress. Factory set locations for TOP PANEL INPUT PCB ASSEMBLY REMOVAL
wire dress, wire ties, ferrites, and anchors should is accomplished by marking and unplugging the
be maintained at all times. Use the following proce- four (4) multi-pin connectors P30-P33 on the Input
dures to disassemble the Bassbreaker 15 for PCB Assembly. Remove the Gain Knob, Control
service access. Please note that all coaxial ca- Nut and Washer. Remove the nut and washer from
bles use multi-pin connectors which are all of the input jack. You can now remove the Front Panel
the same type. During the removal process for Input PCB Assembly.
all of the PCBs these connectors will need to be
disconnected. Since they are all the same in or- SPEAKER JACK PCB ASSEMBLY REMOVAL
der to prevent confusion and miss-wiring it his begins by disconnecting the four (4) fast-on con-
highly recommended that colored markers or nectors P107-P110 from the PCB. Remove the
labels be used to ID the proper cable connector Speaker Jack nuts and washers (Noting their
PCB Header relationship. Also again as stated makeup for reassembly). The PCB can now be re-
several photos should be taken to assure prop- moved from the chassis.
er wire dress during reassembly.
IMPEDANCE SELECTOR SWITCH PCB ASSEM-
CHASSIS REMOVAL is accomplished by first re- BLY REMOVAL is initiated by disconnecting the
moving the five (5) screws from the rear upper seven (7) fast-on connectors noting the color code
screen panel. Next remove the five (5) screws indicated on the PCB. Remove the two (2) screws
which secure the rear lower panel to the cabinet. holding the PCB Assembly to the back panel. The
On the Combo Version Only disconnect the Speak- PCB Assembly can now be removed from the chas-
er Terminal Wires at the Speaker. Remove the two sis.
(2) side chassis screws (4 total) on the left and right
side of the cabinet. Now supporting the chassis re- GAIN/STRUCTURE CONTROL PCB ASSEMBLY
move the two (2) top chassis screws and remove REMOVAL is started by marking and unplugging
the chassis from the cabinet. Access to the inside of the five (5) multi-pin connectors P39-P43. Remove
the chassis can then be accomplished by removing the control knob, nut, and washer. The PCB can
the seven (7) screws which secure the rear chassis now be removed.
cover and folding it back out of the way.
CONTROL PCB ASSEMBLY REMOVAL begins by
REAR PANEL PCB ASSEMBLY REMOVAL is ac- marking and unplugging the five (5) multi-pin con-
complished by first marking and unplugging the five nectors P34-P38. Clip the wire tie located on the
(5) PCB multi-wire connectors at designation #P44- rear right corner of the PCB. Remove the five (5)
P48 from the I/O PCB Assembly. Next remove the top panel control knobs, nuts and washers to sepa-
two screws holding the Line Out XLR Jack to the rate the PCB from the Top Panel.
6
BASSBREAKER™ 15
(This is the model name for warranty claims)
TUBE PCB ASSEMBLY REMOVAL starts by re- these PCB assemblies have been removed you will
moving the tubes and the thirteen (13) screws have full access to the top side of the Power PCB
which hold the PCB to the bottom side of the chas- Assembly. Before attempting to remove the Tube
sis. At this point by pulling up on the PCB and tilting PCB and Power PCB Assemblies as a unit every
it forward you should have enough access to re- attempt should be made to repair the Power PCB
place most of the components located on the board. Assembly from the top side. If top side repair is im-
If it becomes necessary to remove the PCB it is possible then proceed with the Tube PCB/Power
best done by also removing the Power Supply PCB PCB Removal.
Assembly at the same time. This is due to the fact
that the boards are hardwired together. The proce- Start the Tube PCB Assembly and Power Supply
dure for removing the Power PCB Assembly follows PCB Assembly removal by marking and disconnect-
below. Again it is a very good idea to take a few dig- ing the fast-on connections from the Power
ital photos and color marking or labeling all multi-pin Transformer, Output Transformer, Choke and Mute
connectors before disassembly to make sure origi- Switch. These are labeled as P3-P8, P49, & P50
nal factory wiring and wire dress is maintained. from the Power Supply PCB and P21-P23, P25 &
P27 from the Tube PCB. Remove the thirteen (13)
POWER PCB ASSEMBLY REMOVAL as stated screws securing the Power Supply PCB to the
above must be accomplished by first removing the Chassis bottom. At this point you should be able to
Rear Panel PCB Assembly, Speaker Jack PCB As- carefully remove the two (2) PCB Assemblies from
sembly, Input PCB Assembly, Gain/Structure PCB the chassis.
Assembly, and the Control PCB Assembly. Once
CIRCUIT DESCRIPTION
This section provides concise information about AC coupling cap C56 feeds the GAIN control via a
new or unusual circuit designs incorporated into this coax. GAIN control R123 is on the INPUT PCB. A
amplifier model. The purpose is to aid the service coax sends this signal to the GAIN CONTROL PCB
technician by providing insight into the design areas to be routed via the first section of rotary switch S1.
most likely to become obstacles in troubleshooting.
The S1 rotary switch is a two section control that
Information is focused for its effective use while
provides signal routing for the LOW, MED, & HIGH
maintaining the security of Fender® proprietary in-
Gain STRUCTUREs available.
formation wherever possible.
For the LOW Gain STRUCTURE, S1-A &B routes
PRE-AMPLIFIER the V5-A signal directly to gain stage U4-B to drive
the tone controls. The LOW Gain STRUCTURE
The guitar input signal is injected into INPUT jack
provides 2 stages of tube gain before the tone con-
J6 on the INPUT PCB. Via a coax, this signal is fed
trols.
to the TUBE PCB to the first tube gain stage (V5-A).
7
BASSBREAKER™ 15
(This is the model name for warranty claims)
For the MED Gain STRUCTURE, S1-A routes the The reverb for the line out is summed with the dry
V5-A signal to gain stage V4-A. S1-B routes this signal at op-amp U3-A. An active filter circuit is
medium gain signal to V4-B & then the tone con- configured around op-amp U3-B to provide the
trols. The MED Gain STRUCTURE provides 3 LINE OUT’s SPEAKER CABINET EMULATION
stages of tube gain before the tone controls. equalization when enabled through switch S3.
Switch S4 disconnects the chassis ground connec-
For the HIGH Gain STRUCTURE, the GAIN control
tion to the shell of XLR jack J5 (GROUND LIFT).
feeds gain stage V5-B directly. This additionally
amplified signal is then fed to gain stage V4-A via
POWER AMPLIFIER
rotary switch S1-A. S1-B routes this signal to V4-B
& then the tone controls. The HIGH Gain STRUC- The Power Amplifier is a push-pull design using two
TURE provides 4 stages of tube gain before the EL84s power tubes (V1 & V2) found on the TUBE
tone controls. PCB. Both V1’s & V2’s cathode bias is set to ap-
proximately 40mA using 5W power resistors R70 &
Following the V4-B stage (common to LOW, MED,
R134. Their screen grid bias is set through R77 &
& HIGH Gain STRUCTUREs), AC coupling cap C64
R80.
feeds a coax to send the signal to the TRE-
BLE/BASS/MID tone control circuit (R126, R124, & The power amp’s input is a long tail pair phase in-
R125 respectively) found on the CONTROL PCB. verter configuration. This differential amplifier uses
The MASTER VOLUME control (R127) follows the both halves of a 12AX7 (V3-A & -B). V3’s differen-
tone controls. tial plate signals are AC coupled to the grids of the
EL84 power tubes.
The MASTER VOLUME control’s wiper output is
coaxially coupled to the EFFECTS LOOP’s op amp The EL84 plates drive a custom designed multi-tap
circuitry (U1-A & -B and U2-A). The EFFECTS output transformer (T1 – FMIC # 7706195000) to
LOOP circuitry is found on the REAR PANEL PCB. provide an impedance match for 4, 8, & 16 Ohm
The EFFECTS LOOP SEND is J3; the RETURN is speaker loads. Its primary is connected onto the
J4. The EFFECTS LOOP circuitry is optimized to TUBE PCB and its secondary is connected to the
work with low-level stomp boxes. IMPEDANCE SWITCH PCB mounted on the rear
panel. The output transformer tap is selected using
The EFFECTS LOOP output signal is routed to the
S2 (also on the IMPEDANCE SWITCH PCB).
POWER SUPPLY PCB. Op-amps U8-A & -B condi-
tions the signal to the reverb card (attached to P5 - For the COMBO version, the internal speaker is
FMIC p/n 0096569000). This is a digital hall RE- connected to output transformer secondary thru
VERB “daughter card” mounted above the POWER terminals P109 & P110. The COMBO’s internal
SUPPLY PCB. The REVERB wet output signal is speaker is disconnected when the MAIN SPEAKER
then routed to the CONTROL PCB where control jack (J1) is connected to a speaker load through the
R128 allows the user to set the REVERB’s wet out- ¼” jack. The EXTENSION SPEAKER (J2) will work
put level for its wet/dry mix. in tandem with either the internal or EXTERNAL
speaker. Obviously, the impedance selector switch
The EFFECTS LOOP output (U2-A) and the RE-
should be set to match the effective speaker load
VERB output (U9-B) are sent to summing op-amp
connected internally & externally to the amplifier.
U2-B on the REAR PANEL PCB to create the RE-
VERB’s wet/dry mix. The output of U2-B feeds the For the HEAD version, the amplifier can only drive a
POWER AMP input. JFET Q1 is placed at the non- speaker load if the MAIN SPEAKER jack (J1) is
inverting input of U2-B to kill the signal to the power connected to a ¼” plug. The EXTENSION
amp if the amp is placed in MUTE mode. SPEAKER (J2) will work in tandem with the MAIN
SPEAKER. Obviously, the impedance selector
The LINE OUT signal remains active for silent re-
switch should be set to match the effective speaker
cording when the amp is configured in MUTE.
load connected externally to the amplifier.
8
BASSBREAKER™ 15
(This is the model name for warranty claims)
POWER SUPPLY/MUTE through R63 & R64 on the POWER SUPPLY PCB.
A cable connects this supply to the filaments on the
The Power Supply circuitry is found on the POWER
TUBE PCB at P29. A cable also connects the low
SUPPLY PCB. Its circuitry is typical of a Fender
voltage supplies to the REAR PANEL PCB & CON-
tube amplifier with a choke input filter. The second-
TROL PCB to power their op-amp analog signal
ary side of the Power Transformer consists of 3
processing & control circuitry. The +5V supply
windings: high-voltage winding, low-voltage winding
powers the reverb card that is mounted as a daugh-
and heater winding.
ter card on the POWER SUPPLY PCB.
The high voltage red/red secondary winding is used
The green/green heater secondary winding produc-
to generate the high voltage DC power supplies in
es a 6.8VAC power supply that energizes the EL-84
the amplifier. The high voltage DC power supply is
power tube (V1 & V2) heater filaments. This sec-
energized through a full-wave bridge rectifier con-
ondary does not supply preamp tube filament drive
figuration to filter cap C80. A choke is inserted
as explained above. This secondary is connected
between C80 & C42. The output of this supply filter
to terminals on the TUBE PCB.
provides B+ to the plates of the EL84 power tubes.
The “voltage-drop” resistors R58, R59, & R61, The POWER INDICATOR LED installed inside the
along with their associated filter capacitors C43, control panel jewel. It is controlled by the LM555
C44, & C49, subsequently provide the DC screen- timer installed at U4. U4’s output drives this LED
grid voltages for the power tubes and plate voltages through R46 via its connections to the red & white
for the preamp tube stages in the design. These wires routed from the rear panel to the control pan-
supplies are routed to the TUBE PCB circuitry el.
through 18 AWG wiring between the two PCBs.
If the MUTE is enabled, the LED will flash several
The low voltage brown/brown secondary winding times per second. When this is flashing, audio is
feeds a full-wave bridge & filter configuration to cre- not delivered to the power amp input and nothing
ate input DC voltages for regulators U5-U7. These should be audible. This allows “silent recording”
heat-sinked ICs generate the low voltage +/-15.6V capability through the rear panel’s LINE OUT con-
& +5V DC power supplies. A primary function of the nection.
U5 & U6 power supplies is to provide DC filament
If the MUTE is disabled, the amplifier should be ca-
drive to the preamp tube heaters (V3-5). The DC
pable of delivering audio through an internal &/or an
bipolar filament voltages couple to the heaters
external speaker connection.
.
9
BASSBREAKER™ 15
(This is the model name for warranty claims)
BASSBREAKER™ 15
(This is the model name for warranty claims)
* Non-serviceable part. Replace complete parent assembly. See PCB EXCHANGE POLICY section above.
shaded Unique Fender® part. Order directly from the FMIC Parts Department.
shaded + * Access to this part or assembly is controlled. Please contact the FMIC Customer Service Department.
⚠ Safety Critical Part. Replacement must match Safety Agency –Value, if specified –Type, if specified –Approval Mark(s), if on part.
shaded + ⚠ Both a unique Fender® part and a Safety Critical Part as defined above.
11
BASSBREAKER™ 15
(This is the model name for warranty claims)
BASSBREAKER™ 15
(This is the model name for warranty claims)
* Non-serviceable part. Replace complete parent assembly. See PCB EXCHANGE POLICY section above.
shaded Unique Fender® part. Order directly from the FMIC Parts Department.
shaded + * Access to this part or assembly is controlled. Please contact the FMIC Customer Service Department.
⚠ Safety Critical Part. Replacement must match Safety Agency –Value, if specified –Type, if specified –Approval Mark(s), if on part.
shaded + ⚠ Both a unique Fender® part and a Safety Critical Part as defined above.
13
BASSBREAKER™ 15
(This is the model name for warranty claims)
* Non-serviceable part. Replace complete parent assembly. See PCB EXCHANGE POLICY section above.
shaded Unique Fender® part. Order directly from the FMIC Parts Department.
shaded + * Access to this part or assembly is controlled. Please contact the FMIC Customer Service Department.
⚠ Safety Critical Part. Replacement must match Safety Agency –Value, if specified –Type, if specified –Approval Mark(s), if on part.
shaded + ⚠ Both a unique Fender® part and a Safety Critical Part as defined above.
14
BASSBREAKER™ 15
(This is the model name for warranty claims)
* Non-serviceable part. Replace complete parent assembly. See PCB EXCHANGE POLICY section above.
shaded Unique Fender® part. Order directly from the FMIC Parts Department.
shaded + * Access to this part or assembly is controlled. Please contact the FMIC Customer Service Department.
⚠ Safety Critical Part. Replacement must match Safety Agency –Value, if specified –Type, if specified –Approval Mark(s), if on part.
shaded + ⚠ Both a unique Fender® part and a Safety Critical Part as defined above.
15
BASSBREAKER™ 15
(This is the model name for warranty claims)
* Non-serviceable part. Replace complete parent assembly. See PCB EXCHANGE POLICY section above.
shaded Unique Fender® part. Order directly from the FMIC Parts Department.
shaded + * Access to this part or assembly is controlled. Please contact the FMIC Customer Service Department.
⚠ Safety Critical Part. Replacement must match Safety Agency –Value, if specified –Type, if specified –Approval Mark(s), if on part.
shaded + ⚠ Both a unique Fender® part and a Safety Critical Part as defined above.
16
BASSBREAKER™ 15
(This is the model name for warranty claims)
B+4_TPCB
272mVAC
B+4_TPCB
TP25
R108
TP26
A PR3034 06-NOV-15 SMM
1.33VAC R65
WJ30 TP23
100k
TUBE PCB
100k CONTROL PCB 87mVAC
GRN
INPUT PCB OUTPUT_GAIN
TP24
1W
C8 - CHECK V RATING
C55
GAIN CONTROL PCB 1W C64 OUTPUT_V2B
TONE_IN C75
TP27 B EC 16-0015 31-MAR-16 SMM
C2 - CHECK V RATING R69 OUTPUT_V2A GAIN STRUCTURE
GAIN CONTROL PCB TUBE PCB INPUT_V2B .022
R68 9 6
5mVAC TUBE PCB 100k
C56
.0022 INPUT_GAIN S5-A R107
100k
1 .01 470k H 13 400V 470pF
TP22 1W 400V
OUTPUT_V1A C69 TUBE PCB 1W
C67
V1B_TO_S2A GAIN STRUCTURE
13 INPUT_V2A R74 2
400V
C54
coax
S2B_IN M
8
C S2B_OUT coax
R96 7 V4-B
coax
CW R122
R104 V1B_OUT 3
BRIGHT P40 P20 12AX7A P34 R121
coax P15 P39 L 68k R126
INPUT_V1A H 100k 470pF 47k 270k
110k
INPUT PCB 1 470pF S5-B 6 .0022
coax M 2
A S2A_OUT
coax
P19 V4-A
3 12AX7A 7
8 P26 250k30A
TREBLE
P17 P31 INPUT_V1B 400V P24 P43 S1-B
INST_IN R85 2 R115 R84 7 P41 R95 C74 C76
V5-A coax V5-B R2 R1
L
R75 C81 R73 .0068 CW P35 P48
P30 P18 12AX7A 47k 12AX7A 470k 470k
J6 10k R116 10k 1 270k 68k 470k
P32 P16 C68 470pF C62 R94
INPUT 4.7M S1-A C66 R98 .047 R127
R103 R4 R3 1.2k
3 R66 R118 8 .001 1.2k 47 R105 400V 250k15A
130k 130k 510k 47
D D
2.2MCW 400V 1M CW
R112 2.2M R111 MASTER
R91 R83
2.2M coax R129 100k
2.2M C65 R97 3.3M C58 R82 R124
R123 270k
2.2 1.5k 2.2 2.2k 1M5A
250k15A
R117 GNDA_GS4 GNDA_GS5 GNDA_8 GNDA_8 BASS
TO WJ21 W3 GAIN 3.3M
GNDA_6 GNDA_6
C73
GNDA_GS1 GNDA_GS3
WJ37 GNDA_9 GNDA_9
BLK .022
GNDA_2 GNDA_2 GNDA_2 GNDA_3 GNDA_3 GNDA_3 GNDA_4 GNDA_4 GNDA_4 GNDA_4 GNDA_6 CW
GNDA_1 400V
V1A_TO_S2
R125
P33 P42 25k10A
R5 MID
3.3M
GNDA_GS2 GNDA_9
88mVAC
C19
89mVAC TP33
R15 S3-A 4mVAC
TP32 C15
22pF C23 S3-B TP34
R25 87mVAC
1k 5% R28 CAB EMULATION
TP31 R133
22pF
10k R20 22pF J5
R16 270k 5% R36 R35 5%
100 LINE OUT
GNDCH_RP R41
R24 10k GND LIFT 2
1k 10k 10k 3.3k C10 R17
R29 U2-A C14 6 U3-B
3
C8 C11 3 GNDA_RP 1
10k R10 R33 6 U2-B R37 3 U3-A .01 7
1 DS .22 C16 22 22k
6 U1-B 22k TL072 7 1 R44 R43 5 TL072
2
R22 10k J3 J4 10k TL072 10k TL072
7 22 22 Q1 5 2 S4-A
1M TL072 FX SEND FX RETURN 4.7k 27k
5 J113 GNDA_RP C12 .22
2 U1-A 1 R34
R11 R31 R30 G R21 C24 C25 R13
1 R19 C5 R39 R42 R45 R12 S4-B C7 C6
1k C4 R7 R130 220k 100k .001 100k R18 R131
R23 3 TL072 220pF 10k 20k 100k 1k 220pF 220pF
R14 220pF 1k 10k C1 22k 270k 1k 22k C9
10k 5% R27 C20 D1 10k 22pF 5% 5%
5% 220pF R8 5% .01
10k 220k 5%
R26 2 5% 100k C2 +15.6V_RP R40 R38
220pF
22pF
10k 5% WJ2 10k 10k
R32 5% GNDCH_LOUT
WHT R132
47 TO 1/2 MUTE SWITCH C3
GNDCH_RP GNDCH_RP 100 +297VDC
GNDA_RP WJ3 .01
-15.6V_RP 5% TP40
BLK R9
IMPEDANCE SWITCH PCB
C C
1M
P25 BLU
P11 P44
WJ31
YEL
+199VDC +203VDC
WJ28
ORG B+2_TPCB
P100 GRY
SPEAKER PCB
TP17 TP18
R80
GNDA_RP V1-A 7 T
EL84 Fr270 B+1_TPCB TB J2
C53 9
YLW P101
R99 2W EXTENSION SPEAKER
2 RB
D13
C70
TP37 TP38
R86 2 7
400V TP21 D12
4
S2-A 5 6
22pF C29 22k GNDA_PA 1N5366B P109
6mVAC WJ32 JMP1 GNDCH_SPKR
5% 10k 39V5% WHT
R55 R57
TP35 22pF
22pF
5% R113 +15.6V_RP
3 8
R90
220k
RED -
12AX7A 12AX7A 3 240 5W P104 P106 P108
15k 1k 5% BLK
C40 R53 R89 R70 BLK BLK
6 U8-B 4.7k WJ15 R87 R93 P110 BLK
7 R114 2 1M 1M 47
U8-A RED 8.2k 2 C83
2 P5 5.1k TL072 9
C33 2.2 5 1
1 REVERB_SEND 4.7k TL072 C59 EL84 GNDA_PA
TL072 3 R48
R49 V2-A
3 POWER ON/ U4 .1
22
C51 R52 2mVAC
U9-A
MUTE FLASHER
10k
GNDA_RP LM555
750k R88
820 250V
.047
7 R77
+
R56 R54 1 8 Fr270
TP36 REVERB 6 U9-B GND VCC
CW C79 WJ17 2 7 C63 2W
100k 100k 5.1k 25kB 7 RED TRIG DISCHRG P23
2.2 3 OUTPUT
R60 R62 C77 R128 5 TL072 47 C13 THRESH 6 R106 R102
-
4 5 WJ33 BRN
WJ16 .1 RESET VCONTROL R47
R51
15k 1k +5V BLK 1.5M GRY
220k C28 10k 18k
C52 22pF GNDA_RP .01 +66VDC
5%
TO 1/2 MUTE SWITCH 5% TP19 R92 R101
WJ34
22pF WJ13 R46 BLK 47k 300
5% R119 R120 +297VDC
BLACK GNDA_RP
4.7k TP41
47 47 C78 FEEDBACK
47
CONTROL PANEL
GNDA_PA GNDA_PA
B B
REAR PANEL PCB control pcb - REVERB
+15.6V_RVB
47 47
.1
GNDA_1 GNDA_3 GNDA_2 GNDA_4
R109 8
U9-C
R76
WJ35
47 BLK
47 4 C71
GNDA_4 GNDA_6
GNDA_3
R81 .1
WJ36
BLK
47 GNDA_REV
+15.6V +15.6V_RP
.1 .1 .1 .1
8 8 8 8
U8-C U1-C U2-C U3-C
4 C38 4 4 4
C18 C21 C27
12. TEST POINT 39 - MUTE SWITCH SET TO DOWN POSITION TO PRODUCE A FLASHING POWER INDICATOR
13. MAXIMUM OUTPUT TEST CONDITIONS: .1
11. TEST POINT 38 (REVERB LEVEL) - REVERB CONTROL (R128) SET FULLY CLOCKWISE (MAX) FOR THIS TEST ONLY. .1 .1 .1
ENERGIZE PRODUCT WITH NOMINAL LINE VOLTAGE & FREQUENCY AS DENOTED ON THE PRODUCT'S BACK PANEL GNDA_RP GNDA_RP GNDA_RP
POWER SWITCH & MUTE SWITCH POSITIONED UP (POWER INDICATOR IS LIT CONSTANTLY, NOT FLASHING). 10. FILAMENT VOLTAGE TEST (TEST POINT 5) - NO AC INPUT TO J6; MEASURED ACROSS FILAMENT SECONDARY.
8 OHM RESISTIVE LOAD CONNECTED AT MAIN SPEAKER OUT (J1) 9. ALL AC VOLTAGE TESTS (TEST POINT DENOTED BY CIRCLE AROUND TEST DATA) - INJECT 5mV AC INPUT AT 1kHz TO J6
-15.6V -15.6V_RP rear panel pcb
IMPEDANCE SELECTOR (S2 - BACK PANEL) SET TO 8 OHMS 8. ALL DC VOLTAGE TESTS (TEST POINT DENOTED BY SQUARE BOX AROUND TEST DATA) - NO AC INPUT TO J6
A PANEL CONTROL SETTINGS: 7. ALL VOLTAGES MEASURED WITH RESPECT TO CHASSIS GROUND USING
6. FOR COMBO: P109 & P110 INSTALLED; JMP1 NOT INSTALLED A
TREBLE AT 12:00 A DVM WITH AT LEAST 1MEG AC INPUT IMPEDANCE & 10MEG DC INPUT FOR HEAD: P109 & P110 NOT INSTALLED; JMP1 INSTALLED
THIS DOCUMENT CONTAINS INFORMATION OF R
ALL OTHER CONTROLS INCLUDING GAIN: FULLY CLOCKWISE (MAX) EXCEPT REVERB (MIN) NOMINAL TEST CONDITIONS: INSTRUMENTS AND IS SUBMITTED TO YOU IN MUSICAL INSTRUMENTS
ENERGIZE PRODUCT WITH NOMINAL LINE VOLTAGE & FREQUENCY AS DENOTED ON THE PRODUCT'S BACK PANEL PCB ASSEMBLY P/N'S 7706169000 (COMBO) & 7708263000 (HEAD). CONFIDENCE AND SHALL NOT BE DISCLOSED OR
AT TP30 (J1), OBSERVE CLIPPED OUTPUT OF 15W +/- 20% FOR THE FOLLOWING 1kHz INPUT SIGNAL LEVELS (J6) AT THE TRANSMITTED TO OTHERS WITHOUT AUTHORIZ- Corona, CA U.S.A.
POWER SWITCH & MUTE SWITCH POSITIONED UP (POWER INDICATOR IS LIT CONSTANTLY, NOT FLASHING). 4. ALL DIODES ARE 1N4448. ATION FROM FENDER MUSICAL INSTRUMENTS.
THE 3 GAIN STRUCTURE SETTINGS (S1) BELOW:
8 OHM RESISTIVE LOAD CONNECTED AT MAIN SPEAKER OUT (J1) 3. ALL POLARIZED CAPACITORS IN uF, 20%; 50V MINIMUM.
GAIN STRUCTURE = LOW: INPUT = 15 mVrms
CHECKED BY: TITLE: SERVICE DIAGRAM, COMBINED (schematic)
IMPEDANCE SELECTOR (S2 - BACK PANEL) SET TO 8 OHMS
2. ALL UNPOLARIZED CAPACITORS IN uF, 10% OR BETTER; 50V MINIMUM. DATE: BASSBREAKER 15
GAIN STRUCTURE = MED: INPUT = 3 mVrms PANEL CONTROL SETTINGS:
(POWER SUPPLY BYPASS CAPACITORS ARE 20%). APPROVED BY:
MAIN PCB ASSY
GAIN STRUCTURE = HIGH: INPUT = 0.3 mVrms GAIN AT 12:00
SIZE DRAWING NUMBER REV.
BRIGHT SWITCH OUT DATE:
STRUCTURE CONTROL SWITCH SETTING: LOW 1. ALL RESISTORS IN OHMS, 5%; 1/4W.
DRAWN: GIT'LO ENGR: GIT'LO D 7706210000 B
ALL OTHER CONTROLS FULLY CLOCKWISE (MAX) EXCEPT REVERB (MIN) NOTES: (UNLESS OTHERWISE NOTED) DATABASE FILE: Z3034S.SCH RELEASE DATE: 06-NOV-15 SHEET: 1 OF 3
8 7 6 5 4 3 2 1
8 7 6 5 4 3 2 1
REVISIONS
REV. DESCRIPTION DATE APPROVED
B+2 B+3
REAR PANEL
+311VDC +298VDC +274VDC +257VDC B+4
B+1 TP3 TP4
TP1 TP2 +15.6V P10 P46 +15.6V_RP
WJ24
RED
WJ25
ORG
WJ26
YEL
WJ27
GRN
-15.6V -15.6V_RP
PCB
D2-4, D8: 1N4006 (X4) P/N 0036486000
R58 R59 R61 GNDA_RP
C23-26: 8600pF, 1kV CD-TYPE P49 P50
PRIMARY WIRING - 100V* - 120V: RED P6
Fp1k Fp4.7k Fp4.7k
C31 C36 1W
C43
1W 1W
POWER PCB
D D
C80 C42 C44 C49
22
D3 D4 22 22 450V 22 22
100 -120V: F2AL 450V 450V
105C
450V 450V
WJ21
+15.6V P14 P37
+15.6V_RVB
C30 C41
105C WJ19 WJ20
D2 D8 BLK
220 -240V: F1AL BLK
CONTROL PCB
RT1 TCO: 139C BLK
P13 BLK
P3
RED -15.6V -15.6V_RVB
n n WJ23 *(100V: VIO)* WJ18
L
OPEN GNDA_B4 GNDA_REV
VIO -t
F3
F4 C60-11
C47
.1
GRN P22
R79 connect to input jack
n n WJ22 4 5 4 4 W1
250VAC
TUBE PCB
N 6.8mVAC 3.15A V3-C
POWER WHT R78 V1-B V2-B
TP5
SWITCH P12 P21 5 5
WHT GRN
9 +15.6V
100 1/2W
+15.6VDC +12.2VDC
BRN P4 GNDA_PA
TP8 TP12
F1 D9
7815 +5.0VDC
1A D10
P2 U6 R64 TP10
P7 .1 7805 4
BRN/WHT
C34 IN OUT
1 3 P9 U7 +5V
Fr22 9
IN OUT
2W
P2 FOR 220/240V - SPARE TERMINATION FOR EXTRA WIRE F2
D5 D11
+21.9VDC
GND 1 3 V4-C
2
BRN P8 C50 C46 C35 GND C37
TP6 P29 5
2200 D7 10 1 2 10
1A D5, D9-D11: 1N4006 (X4) 35V 1N4006
W2
D6 4
C32 1N4006
-22.4VDC 9
FOR REVERB
2200 C45
POWER PCB
35V TP7 1 V5-C
10
GND
TUBE PCB
Fr22
-15.7VDC 2W -12.3VDC
TP9 TP11
-15.6V
C C
TABLE 1:
PRIMARY WIRING - 220V-240V BB15 - PRIMARY WIRING & MAINS FUSES FOR INTERNATIONAL SERVICE
RED
P6
LINE VOLTAGE POWER TRANSFORMER COLOR - P13 COLOR - P12 COLOR - P2 MAIN FUSE - FMIC #
220-230V 240V
VIO
TCO: 139C
RED
100 7706194000 VIOLET WHITE X F2A - 0048827000
P13 P13 P3
P4 BRN
A A
THIS DOCUMENT CONTAINS INFORMATION OF R
DATE: BASSBREAKER 15
APPROVED BY:
MAIN PCB ASSY
NOTES: DATE:
SIZE DRAWING NUMBER REV.
8 7 6 5 4 3 2 1
8 7 6 5 4 3 2 1
+154VDC +157VDC REVISIONS
TP15 TP16
B+4_TPCB
+158VDC
+186VDC
B+4_TPCB REV. DESCRIPTION DATE APPROVED
TP13 0.87VAC 1.14VAC
TP14
B+4_TPCB
272mVAC
B+4_TPCB
TP25
R108
TP26
A PR3034 06-NOV-15 SMM
1.33VAC R65
WJ30 TP23
100k
TUBE PCB
100k CONTROL PCB 87mVAC
GRN
INPUT PCB OUTPUT_GAIN
TP24
1W
C8 - CHECK V RATING
C55
GAIN CONTROL PCB 1W C64 OUTPUT_V2B
TONE_IN C75
TP27 B EC 16-0015 31-MAR-16 SMM
C2 - CHECK V RATING R69 OUTPUT_V2A GAIN STRUCTURE
GAIN CONTROL PCB TUBE PCB
5mVAC TUBE PCB
R68
100k
C56
.0022 INPUT_GAIN S5-A R107
100k
1 .01 470k H
9
13
INPUT_V2B
6
.022
400V 470pF C EC 16-0026 09-MAY-16 SMM
TP22 1W 400V
OUTPUT_V1A C69 TUBE PCB 1W
C67
V1B_TO_S2A GAIN STRUCTURE
13 INPUT_V2A R74 2
400V
C54
coax
S2B_IN M
8
C S2B_OUT coax
R96 7 V4-B
coax
CW R122
R104 V1B_OUT 3
BRIGHT P40 P20 12AX7A P34 R121
coax P15 P39 L 68k R126
INPUT_V1A H 100k 470pF 47k 270k
110k
INPUT PCB 1 470pF S5-B 6 .0022
coax M 2
A S2A_OUT
coax
P19 V4-A
3 12AX7A 7
8 P26 250k30A
TREBLE
P17 P31 INPUT_V1B 400V P24 P43 S1-B
INST_IN R85 2 R115 R84 7 P41 R95 C74 C76
V5-A coax V5-B R2 R1
L
R75 C81 R73 .0068 CW P35 P48
P30 P18 12AX7A 47k 12AX7A 470k 470k
J6 10k R116 10k 1 270k 68k 470k
P32 P16 C68 470pF C62 R94
INPUT 4.7M S1-A C66 R98 .047 R127
R103 R4 R3 1.2k
3 R66 R118 8 .001 1.2k 47 R105 400V 250k15A
130k 130k 510k 47
D D
2.2MCW 400V 1M CW
R112 2.2M R111 MASTER
R91 R83
2.2M coax R129 100k
2.2M C65 R97 3.3M C58 R82 R124
R123 270k
2.2 1.5k 2.2 2.2k 1M5A
250k15A
R117 GNDA_GS4 GNDA_GS5 GNDA_8 GNDA_8 BASS
TO WJ21 W3 GAIN 3.3M
GNDA_6 GNDA_6
C73
GNDA_GS1 GNDA_GS3
WJ37 GNDA_9 GNDA_9
BLK .022
GNDA_2 GNDA_2 GNDA_2 GNDA_3 GNDA_3 GNDA_3 GNDA_4 GNDA_4 GNDA_4 GNDA_4 GNDA_6 CW
GNDA_1 400V
V1A_TO_S2
R125
P33 P42 25k10A
R5 MID
3.3M
GNDA_GS2 GNDA_9
88mVAC
C19
89mVAC TP33
R15 S3-A 4mVAC
TP32 C15
22pF C23 S3-B TP34
R25 87mVAC
1k 5% R28 CAB EMULATION
TP31 R133
22pF
10k R20 22pF J5
270k 5% R36 R35 5%
100 LINE OUT
GNDCH_RP R41
R24 10k GND LIFT 2
10k 10k 3.3k C10 R17
R29 U2-A C14 6 U3-B
3
C8 C11 3 GNDA_RP 1
10k R10 R33 6 U2-B R37 3 U3-A .01 7
T 1 DS .22 C16 22 22k
6 U1-B 22k TL072 7 1 R44 R43 5 TL072
2
R22 10k TS J3 J4 10k TL072 10k TL072
7 22 22 Q1 5 2 S4-A
1M TL072 RS FX SEND FX RETURN 4.7k 27k
5 J113 GNDA_RP C12 .22
U1-A 1 R R34
2 S R31 R30 C25
R19 R136 C5 R11 G R21 R39 C24 R13 C7 C6
1 1k R42 R45 R12 S4-B R18 R131
C4 R7 R130 220k 100k .001 100k
R23 3 TL072 2 220pF 10k 20k 100k 1k 220pF 220pF
R14 220pF 1k 10k C1 47 22k 270k 1k 22k C9
10k R8 5% C20 D1 10k 22pF 5% 5%
5% 220pF 1k R27 5% .01
10k 100k 5%
R26 5% C85 R16 C2 220k +15.6V_RP R40 R38
2
1 220pF
22pF
10k 5% WJ2 10k 10k
.01 R32 5% GNDCH_LOUT
WHT R132
47 TO 1/2 MUTE SWITCH C3
GNDCH_RP 100 +297VDC
GNDA_RP WJ3 .01
-15.6V_RP 5% TP40
BLK R9
IMPEDANCE SWITCH PCB
C C
1M
P25 BLU
P11 P44
WJ31
YEL
+199VDC +203VDC
WJ28
ORG B+2_TPCB
P100 GRY
SPEAKER PCB
TP17 TP18
R80
GNDA_RP V1-A 7 T
EL84 Fr270 B+1_TPCB TB J2
C53 9
YLW P101
R99 2W EXTENSION SPEAKER
2 RB
D13
C70
TP37 TP38
R86 2 7
400V TP21 D12
4
S2-A 5 6
22pF C29 22k GNDA_PA 1N5366B P109
6mVAC WJ32 JMP1 GNDCH_SPKR
5% 10k 39V5% WHT
R55 R57
TP35 22pF
22pF
5% R113 +15.6V_RP
3 8
R90
220k
RED -
12AX7A 12AX7A 3 240 5W P104 P106 P108
15k 1k 5% BLK
C40 R53 R89 R70 BLK BLK
6 U8-B 4.7k WJ15 R87 R93 P110 BLK
7 R114 2 1M 1M 47
U8-A RED 8.2k 2 C83
2 P5 5.1k TL072 9
C33 2.2 5 1
1 REVERB_SEND 4.7k TL072 C59 EL84 GNDA_PA
TL072 3 R48
R49 V2-A
3 POWER ON/ U4 .1
22
C51 R52 2mVAC
U9-A
MUTE FLASHER
10k
GNDA_RP LM555
750k R88
820 250V
.047
7 R77
+
R56 R54 1 8 Fr270
TP36 REVERB 6 U9-B GND VCC
CW C79 WJ17 2 7 C63 2W
100k 100k 5.1k 25kB 7 RED TRIG DISCHRG P23
2.2 3 OUTPUT
R60 R62 C77 R128 5 TL072 47 C13 THRESH 6 R106 R102
-
4 5 WJ33 BRN
WJ16 .1 RESET VCONTROL R47
R51
15k 1k +5V BLK 1.5M GRY
220k C28 10k 18k
C52 22pF GNDA_RP .01 +66VDC
5%
TO 1/2 MUTE SWITCH 5% TP19 R92 R101
WJ34
22pF WJ13 R46 BLK 47k 300
5% R119 R120 +297VDC
BLACK GNDA_RP
4.7k TP41
47 47 C78 FEEDBACK
47
CONTROL PANEL
GNDA_PA GNDA_PA
B B
REAR PANEL PCB control pcb - REVERB
+15.6V_RVB
47 47
.1
GNDA_1 GNDA_3 GNDA_2 GNDA_4
R109 8
U9-C
R76
WJ35
47 BLK
47 4 C71
GNDA_4 GNDA_6
GNDA_3
R81 .1
WJ36
BLK
47 GNDA_REV
+15.6V +15.6V_RP
.1 .1 .1 .1
8 8 8 8
U8-C U1-C U2-C U3-C
4 C38 4 4 4
C18 C21 C27
12. TEST POINT 39 - MUTE SWITCH SET TO DOWN POSITION TO PRODUCE A FLASHING POWER INDICATOR
13. MAXIMUM OUTPUT TEST CONDITIONS: .1
11. TEST POINT 38 (REVERB LEVEL) - REVERB CONTROL (R128) SET FULLY CLOCKWISE (MAX) FOR THIS TEST ONLY. .1 .1 .1
ENERGIZE PRODUCT WITH NOMINAL LINE VOLTAGE & FREQUENCY AS DENOTED ON THE PRODUCT'S BACK PANEL GNDA_RP GNDA_RP GNDA_RP
POWER SWITCH & MUTE SWITCH POSITIONED UP (POWER INDICATOR IS LIT CONSTANTLY, NOT FLASHING). 10. FILAMENT VOLTAGE TEST (TEST POINT 5) - NO AC INPUT TO J6; MEASURED ACROSS FILAMENT SECONDARY.
8 OHM RESISTIVE LOAD CONNECTED AT MAIN SPEAKER OUT (J1) 9. ALL AC VOLTAGE TESTS (TEST POINT DENOTED BY CIRCLE AROUND TEST DATA) - INJECT 5mV AC INPUT AT 1kHz TO J6
-15.6V -15.6V_RP rear panel pcb
IMPEDANCE SELECTOR (S2 - BACK PANEL) SET TO 8 OHMS 8. ALL DC VOLTAGE TESTS (TEST POINT DENOTED BY SQUARE BOX AROUND TEST DATA) - NO AC INPUT TO J6
A PANEL CONTROL SETTINGS: 7. ALL VOLTAGES MEASURED WITH RESPECT TO CHASSIS GROUND USING
6. FOR COMBO: P109 & P110 INSTALLED; JMP1 NOT INSTALLED A
TREBLE AT 12:00 A DVM WITH AT LEAST 1MEG AC INPUT IMPEDANCE & 10MEG DC INPUT FOR HEAD: P109 & P110 NOT INSTALLED; JMP1 INSTALLED
THIS DOCUMENT CONTAINS INFORMATION OF R
ALL OTHER CONTROLS INCLUDING GAIN: FULLY CLOCKWISE (MAX) EXCEPT REVERB (MIN) NOMINAL TEST CONDITIONS: INSTRUMENTS AND IS SUBMITTED TO YOU IN MUSICAL INSTRUMENTS
ENERGIZE PRODUCT WITH NOMINAL LINE VOLTAGE & FREQUENCY AS DENOTED ON THE PRODUCT'S BACK PANEL PCB ASSEMBLY P/N'S 7706169000 (COMBO) & 7708263000 (HEAD). CONFIDENCE AND SHALL NOT BE DISCLOSED OR
AT TP30 (J1), OBSERVE CLIPPED OUTPUT OF 15W +/- 20% FOR THE FOLLOWING 1kHz INPUT SIGNAL LEVELS (J6) AT THE TRANSMITTED TO OTHERS WITHOUT AUTHORIZ- Corona, CA U.S.A.
POWER SWITCH & MUTE SWITCH POSITIONED UP (POWER INDICATOR IS LIT CONSTANTLY, NOT FLASHING). 4. ALL DIODES ARE 1N4448. ATION FROM FENDER MUSICAL INSTRUMENTS.
THE 3 GAIN STRUCTURE SETTINGS (S1) BELOW:
8 OHM RESISTIVE LOAD CONNECTED AT MAIN SPEAKER OUT (J1) 3. ALL POLARIZED CAPACITORS IN uF, 20%; 50V MINIMUM.
GAIN STRUCTURE = LOW: INPUT = 15 mVrms
CHECKED BY: TITLE: SERVICE DIAGRAM, COMBINED (schematic)
IMPEDANCE SELECTOR (S2 - BACK PANEL) SET TO 8 OHMS
2. ALL UNPOLARIZED CAPACITORS IN uF, 10% OR BETTER; 50V MINIMUM. DATE: BASSBREAKER 15
GAIN STRUCTURE = MED: INPUT = 3 mVrms PANEL CONTROL SETTINGS:
(POWER SUPPLY BYPASS CAPACITORS ARE 20%). APPROVED BY:
MAIN PCB ASSY
GAIN STRUCTURE = HIGH: INPUT = 0.3 mVrms GAIN AT 12:00
SIZE DRAWING NUMBER REV.
BRIGHT SWITCH OUT DATE:
STRUCTURE CONTROL SWITCH SETTING: LOW 1. ALL RESISTORS IN OHMS, 5%; 1/4W.
DRAWN: GIT'LO ENGR: GIT'LO D 7706210000 C
ALL OTHER CONTROLS FULLY CLOCKWISE (MAX) EXCEPT REVERB (MIN) NOTES: (UNLESS OTHERWISE NOTED) DATABASE FILE: Z3034S.SCH RELEASE DATE: 06-NOV-15 SHEET: 1 OF 3
8 7 6 5 4 3 2 1
8 7 6 5 4 3 2 1
REVISIONS
REV. DESCRIPTION DATE APPROVED
B+2 B+3
C EC 16-0026 09-MAY-16 SMM
REAR PANEL
+311VDC +298VDC +274VDC +257VDC B+4
B+1 TP3 TP4
TP1 TP2 +15.6V P10 P46 +15.6V_RP
WJ24
RED
WJ25
ORG
WJ26
YEL
WJ27
GRN
-15.6V -15.6V_RP
PCB
D2-4, D8: 1N4006 (X4) P/N 0036486000
R58 R59 R61 GNDA_RP
C23-26: 8600pF, 1kV CD-TYPE P49 P50
PRIMARY WIRING - 100V* - 120V: RED P6
Fp1k Fp4.7k Fp4.7k
C31 C36 1W
C43
1W 1W
POWER PCB
D D
C80 C42 C44 C49
22
D3 D4 22 22 450V 22 22
100 -120V: F2AL 450V 450V
105C
450V 450V
WJ21
+15.6V P14 P37
+15.6V_RVB
C30 C41
105C WJ19 WJ20
D2 D8 BLK
220 -240V: F1AL BLK
CONTROL PCB
RT1 TCO: 139C BLK
P13 BLK
P3
RED -15.6V -15.6V_RVB
n n WJ23 *(100V: VIO)* WJ18
L
OPEN GNDA_B4 GNDA_REV
VIO -t
F3
F4 C60-11
C47
.1
GRN P22
R79 connect to input jack
n n WJ22 4 5 4 4 W1
250VAC
TUBE PCB
N 6.8mVAC 3.15A V3-C
POWER WHT R78 V1-B V2-B
TP5
SWITCH P12 P21 5 5
WHT GRN
9 +15.6V
100 1/2W
+15.6VDC +12.2VDC
BRN P4 GNDA_PA
TP8 TP12
F1 D9
7815 +5.0VDC
1A D10
P2 U6 R64 TP10
P7 .1 7805 4
BRN/WHT
C34 IN OUT
1 3 P9 U7 +5V
Fr22 9
IN OUT
2W
P2 FOR 220/240V - SPARE TERMINATION FOR EXTRA WIRE F2
D5 D11
+21.9VDC
GND 1 3 V4-C
2
BRN P8 C50 C46 C35 GND C37
TP6 P29 5
2200 D7 10 1 2 10
1A D5, D9-D11: 1N4006 (X4) 35V 1N4006
W2
D6 4
C32 1N4006
-22.4VDC 9
FOR REVERB
2200 C45
POWER PCB
35V TP7 1 V5-C
10
GND
TUBE PCB
Fr22
-15.7VDC 2W -12.3VDC
TP9 TP11
-15.6V
C C
TABLE 1:
PRIMARY WIRING - 220V-240V BB15 - PRIMARY WIRING & MAINS FUSES FOR INTERNATIONAL SERVICE
RED
P6
LINE VOLTAGE POWER TRANSFORMER COLOR - P13 COLOR - P12 COLOR - P2 MAIN FUSE - FMIC #
220-230V 240V
VIO
TCO: 139C
RED
100 7706194000 VIOLET WHITE X F2A - 0048827000
P13 P13 P3
P4 BRN
A A
THIS DOCUMENT CONTAINS INFORMATION OF R
DATE: BASSBREAKER 15
APPROVED BY:
MAIN PCB ASSY
NOTES: DATE:
SIZE DRAWING NUMBER REV.
8 7 6 5 4 3 2 1