Beruflich Dokumente
Kultur Dokumente
QUESTION NO: 1
You wish to advertise LDP labels for all local networks; which is the most effective policy
statement to use?
A.
from prefix-list direct
B.
match local
C.
from protocol direct
D.
match protocol direct
E.
from protocol local
Answer: C
Explanation:
QUESTION NO: 2
Which of the following indicates the path over which an LSP's tail end router will return an RSVP
RESV message?
A.
The IGP FIB.
B.
The Reservation State Block (RSB)
C.
The Path State Block (PSB)
D.
The opaque database.
Answer: C
QUESTION NO: 3
A.
Router R1
B.
Router R2
C.
Router R3
D.
Router R4
E.
Router R5
Answer: B
Explanation:
QUESTION NO: 4
Given the output below, which of the following statements are true? (Choose three)
A.
A packet arriving with label 131066 and destined for prefix 10.10.10.243/32 will be forwarded out
interface 1/1/4, with label 131070.
B.
LDP ECMP is enabled.
C.
The router’s system address is 10.10.10.242/32.
D.
There are multiple LSPs to reach FEC 10.10.10.244/32.
E.
The router cannot receive any unlabeled packets destined for prefix 10.10.10 223/32.
Answer: A,B,D
"Pass Any Exam. Any Time." - www.actualtests.com 4
Nokia 4A0-103 Exam
Explanation:
QUESTION NO: 5
Which of the following statements best describe MPLS fast reroute characteristics? (Choose two)
A.
Fast reroute requires you to manually define detour paths.
B.
Fast reroute provides path protection close to the failure point
C.
Fast reroute performs automatic path calculation and signaling.
D.
Fast reroute protects both primary and secondary paths.
Answer: B,C
Explanation:
QUESTION NO: 6
During node protection signaling, the PLR knows the address of the MP from which of the
following methods?
A.
The PLR issues a RSVP path message to the destination router to request the address of the MP.
B.
The PLR learns the address of the MP from the ERO.
C.
The PLR learns the address of the MP from the RRO
D.
The PLR learns the address of the MP from the targeted RSVP hello message.
E.
The PLR does not need to know the address of the MP.
QUESTION NO: 7
What is the significance of receiving a packet with the bottom MPLS label S bit set to 1?
A.
It results in forwarding based on the next packet header.
B.
It indicates that the label is the bottom of the MPLS label stack.
C.
It indicates that the label is the top of the MPLS label stack.
D.
Any LSR that receives an S bit set to 1 must discard the packet.
Answer: B
Explanation:
QUESTION NO: 8
Which command can be used to verify the LDP settings for label distribution and retention?
A.
show router ldp default
B.
show router ldp parameters
C.
show router ldp settings
D.
show router mpls settings
E.
show router mpls label-options
QUESTION NO: 9
Router R3 signals an LSP, reserving 1Gbps bandwidth on a 10Gbps link. RSVP configuration
limits reservable bandwidth to 20 percent on the egress interface. Which of the following
statements is true?
A.
The egress RSVP interface has 80 percent bandwidth unreserved.
B.
LSPs can reserve an additional 9.9 Gbps bandwidth on this RSVP interface.
C.
The head end reserves 100Mbps for the LSP
D.
The egress RSVP interface has 1 Gbps bandwidth unreserved.
Answer: D
Explanation:
QUESTION NO: 10
Assuming that LSP R1-R2-R3 requests the default fast reroute configuration, which router
becomes a DMP for the detour tunnels?
A.
Router R1
B.
Router R2
C.
Router R3
D.
Router R4
E.
Router R5
Answer: E
Explanation:
QUESTION NO: 11
Which of the following message types does RSVP use to set up an LSP? (Choose two)
A.
Path message
B.
"Pass Any Exam. Any Time." - www.actualtests.com 8
Nokia 4A0-103 Exam
iLER message
C.
Resv message
D.
LSP setup call request
E.
eLER message
Answer: A,C
Explanation:
QUESTION NO: 12
Assume that, on the Alcatel-Lucent 7750 SR, an LSP is configured with one-to-one FRR and node
protection. Which of the following statements are FALSE? (Choose two)
A.
Each PLR signals a detour LSP that avoids the downstream node. If the downstream node cannot
be avoided, a detour LSP that avoids the downstream link is signaled.
B.
The detour LSP can take one or more hops before merging back on the protected LSP.
C.
The merge point of the protected LSP must be the next-next-hop node
D.
The ingress router will set the local protection desired flag in the session attribute object of the
path message to inform all routers along the protected LSP path to establish detour LSPs.
E.
The label recording desired flag must be set in the session attribute object in order for the PLR to
know what label to swap when using the detour LSP.
Answer: C,E
Explanation:
QUESTION NO: 13
A.
Router R1 is the LSP originator and is also a PLR.
B.
With one-to-one link or node protection, the detour LSP path is R1-R4-R5-R2-R3.
C.
With one-to-one link or node protection, the detour LSP path is R1-R4-R5-R3.
D.
If the R2-R3 link fails, router R3 becomes a PLR
E.
None of the nodes can be protected with FRR.
Answer: A,C
Explanation:
QUESTION NO: 14
Which of the following statements regarding LSP path configuration are true? (Choose three)
B.
The path may be used multiple times in a single LSP.
C.
The path may comprise loose hop entries only.
D.
The path must define the LSP's tail end.
E.
The path may be used for multiple LSPs.
Answer: A,D,E
Explanation:
QUESTION NO: 15
A.
Router R1
B.
Router R4
C.
Router R2
D.
Router R3
Answer: B,D
Explanation:
QUESTION NO: 16
Which of the following statements best describes downstream unsolicited label distribution?
A.
An LER may answer requests for label mappings immediately, without waiting for a label mapping
from the next-hop.
B.
An LER may advertise label mappings to all peers for which it might be a next-hop for a given
FEC.
C.
An LER propagates a label mapping downstream for a FEC. only if it has a label mapping for the
FEC next-hop.
D.
An LER will only distribute a label for a FEC when it has been requested to do so.
Answer: B
Explanation:
QUESTION NO: 17
"Pass Any Exam. Any Time." - www.actualtests.com 12
Nokia 4A0-103 Exam
In MPLS, labels are distributed in the opposite direction of the data flow.
A.
TRUE
B.
FALSE
Answer: A
Explanation:
QUESTION NO: 18
Given the configuration below, what is the system ID of the destination node?
A.
10.32.1.2
B.
10.1.478
D.
Cannot tell from this configuration
E.
10.1.2.2
Answer: B
Explanation:
QUESTION NO: 19
Which of the following is defined by the following statement? All label mappings received from all
peer LSRs are saved.
A.
Conservative label retention
B.
Liberal label retention.
C.
Downstream on demand.
D.
Downstream unsolicited.
Answer: B
Explanation:
QUESTION NO: 20
A.
Each implementation can use them as they see fit.
B.
They are used to carry the Ethertype value.
D.
They are used to carry QoS classification.
E.
They are used to carry fragmentation flag information
Answer: D
Explanation:
QUESTION NO: 21
If an LSP's loose primary path includes the statement "include green" and "exclude red;" how does
CSPF choose the LSP's path?
A.
CSPF chooses a link that is a member of both administrative groups
B.
CSPF chooses only those links that are NOT members of the green admin group
C.
CSPF prunes the green links and uses these links for the secondary path
D.
CSPF signals the LSP path over the green links only, and prunes all other links
Answer: D
Explanation:
QUESTION NO: 22
A.
Both the primary and secondary paths are explicitly defined.
B.
The primary path is active and the secondary path is in hot standby.
C.
The LSP defined will use the primary path and will signal the secondary path to become active if
the primary path fails.
D.
The LSP has the same source and destination for both primary and secondary paths.
Answer: B
Explanation:
QUESTION NO: 23
Which of the following commands may only be used on the head end router to verify the status of
an LSP named "LSP 1"? (Choose two)
A.
show router mpls Isp "LSP 1" originate
B.
show router mpls Isp "LSP 1" path detail
C.
show router rsvp session originate
Answer: B,C
Explanation:
QUESTION NO: 24
Which of the following are the default settings for the Alcatel-Lucent 7750 SR when using LDP?
A.
Ordered control mode; downstream on demand.
B.
Ordered control mode; downstream unsolicited.
C.
Independent control mode; downstream on demand.
D.
Independent control mode; downstream unsolicited.
Answer: B
Explanation:
QUESTION NO: 25
Which default LDP parameter are you able to change with CLI?
A.
Label space mode
B.
Label retention
C.
Control mode
D.
Keepalive factor
QUESTION NO: 26
A.
It is unidirectional.
B.
It is bidirectional.
C.
It must always have a secondary path.
D.
It provides a specific tunnel for a FEC through the network.
E.
It always follows the IGP best path.
Answer: A,D
Explanation:
QUESTION NO: 27
A.
LSR
B.
LER
C.
eLER
D.
iLER
E.
Answer: D
Explanation:
QUESTION NO: 28
When configuring an LSP for fast reroute one-to-one protection, which of the following statements
is true?
A.
The LSP can also use facility backup.
B.
The LSP is limited to node protection.
C.
You cannot request bandwidth on the protected LSP.
D.
Node protection can be disabled.
Answer: D
Explanation:
QUESTION NO: 29
Which of the following are functions of the MPLS control plane in a router? (Choose two)
A.
Label allocation and management.
B.
Label swapping.
C.
Pushing a label on an unlabeled packet.
D.
Label signaling.
Answer: A,D
Explanation:
QUESTION NO: 30
Which of the following statements regarding RSVP refresh reduction are true? (Choose two)
A.
Message-IDs replace individual refresh messages.
B.
Refresh reduction applies only to reservation messages.
C.
RSVP generates a summary-refresh message for each LSP.
D.
An LSP state change causes an incremented Message-ID.
Answer: A,D
Explanation:
QUESTION NO: 31
Which of the following reservation styles can be used to prevent both the primary and secondary
paths from booking resources on a common link?
A.
Fixed filter
B.
Shared explicit
C.
Standby explicit LSP
D.
Preemptive filter
Answer: B
Explanation:
QUESTION NO: 32
A.
RSVP-TE operates in a downstream unsolicited label advertisement mode.
B.
RSVP-TE makes use of ordered control mode.
C.
RSVP-TE is an MPLS signaling protocol, based on the resource reservation protocol.
D.
RSVP-TE enables the establishment of explicitly routed LSPs that can be automatically routed
away from network failures
E.
RSVP-TE supports explicitly routed LSPs using either loose or strict route definitions.
Answer: A
Explanation:
QUESTION NO: 33
- Router R1 in Area 0 generates LDP labels for FECs 10.10.102/31 and 10.10.10.4/31
Router R3 in Area 1 places these FECs in its LIB, but it does not place them in its LFIB. What can
you do on router R3 to make it populate these labels in its LFIB?
A.
Disable route summarization on router R3
B.
Enable LDP aggregate prefix match
C.
Create an import policy to accept these FECs
D.
Disable LDP exact match on the specified FECs
Answer: B
Explanation:
QUESTION NO: 34
A.
CSPF looks for the delta bandwidth, taking down the first path if necessary.
B.
CSPF looks for the delta bandwidth, implementing make-before-break.
C.
After 5 failed attempts to find the bandwidth requested, the head end disables the LSP.
D.
CSPF looks for the entire bandwidth requested, implementing MBB.
Answer: B
Explanation:
QUESTION NO: 35
Which approach to LSP path diversity provides the most control, but the least flexibility?
A.
Administrative Groups
B.
Shared Risk Link Groups
C.
Strict hop LSP paths
D.
Fast reroute
Answer: C
Explanation:
QUESTION NO: 36
If an Alcatel-Lucent 7750 LSR receives a labeled packet with a outer label TTL of 250 and an
inner label TTL of 251, which of the following statements is true?
B.
The packet will be label switched; the outer label TTL will be 249 and the inner label TTL will be
251.
C.
The packet will be label switched; both the outer label TTL and the inner label TTL will be 250.
D.
The packet will be label switched; both the outer label TTL and the inner label TTL will be 249,
because they must be the same.
Answer: B
Explanation:
QUESTION NO: 37
A.
An LSP is a bidirectional path across the MPLS domain.
B.
An LSP is a bidirectional path for a particular FEC across the MPLS domain.
C.
An LSP is a unidirectional path across the MPLS domain.
D.
An LSP is a bidirectional path between adjacent LSRs.
E.
An LSP is a unidirectional path between adjacent LSRs.
Answer: C
Explanation:
QUESTION NO: 38
-LSP1.R1-R4-R5-R3
-LSP2.R1-R4-R5-R2
A.
Router R1
B.
Router R2
C.
Router R3
D.
Router R4
E.
Router R5
Answer: A,E
Explanation:
QUESTION NO: 39
You wish to build an LSP originating on router R1, transiting the path R1-R2-R4-R5-R6, and
terminating on router R6. How many strict hops would you define in your path statement?
B.
1
C.
5
D.
6
Answer: A
Explanation:
QUESTION NO: 40
Which of the following statements regarding the last two octets of the LDP identifier is true?
A.
It is always a random 16-bit number.
B.
It is always zero for per-interface label space.
C.
It is always non-zero.
D.
It is always zero for per-platform label space.
E.
It is always non-zero for per-platform label space.
Answer: D
Explanation:
QUESTION NO: 41
Which of the following prerequisites must you configure on a router to enable LDP-over-RSVP
support? (Choose two)
B.
Configure tunneled T-LDP sessions between PE routers.
C.
Enable Idp-over-rsvp in the IGP configuration on the PEs and ABRs
D.
Enable LSP stitching on the RSVP LSPs
Answer: A,C
Explanation:
QUESTION NO: 42
A.
The path message's IP header options field sets the router alert option.
B.
The IP header source address is the sender's egress interface address.
C.
The IP header destination address is the next-hop interface address.
D.
The IP header HOP object reflects the upstream router's egress interface address.
Answer: A
Explanation:
QUESTION NO: 43
A.
It identifies the FEC.
C.
It identifies the origin of the packet.
D.
It specifies the type of data contained in the packet
Answer: A
Explanation:
QUESTION NO: 44
A.
The Maximum Allocation Model (MAM) provides the most efficient bandwidth utilization model
B.
In the Maximum Allocation Model (MAM), each CT receives dedicated bandwidth constraints.
C.
In the Russian Doll Model (RDM), a CT2 LSP automatically preempts a CT1 LSP.
D.
Using the Russian Doll Mode! (RDM), a CT1 LSP may use unreserved CTO bandwidth.
Answer: B
Explanation:
QUESTION NO: 45
Which of the following routing protocols are supported on the Alcatel-Lucent 7750 SR to enable
constraint-based LSPs? (Choose two)
A.
RIPv2-TE
B.
CSPF
D.
ISIS-TE
E.
RSVP-TE
Answer: C,D
Explanation:
QUESTION NO: 46
Which of the following statements is true when the implicit null is implemented?
A.
The penultimate router will POP the top label from the packets.
B.
The eLER will receive packets with a top label value of 3.
C.
The eLER will receive packets with a top label value of 0.
D.
The penultimate router will always receive unlabeled packets.
E.
The penultimate router performs a double lookup on the packet.
Answer: A
Explanation:
QUESTION NO: 47
Which of the following is described by the following statement? An LSR propagates a label
mapping only for a FEC for which it has a label mapping for the FEC next-hop.
A.
Independent control mode
C.
Liberal label retention
D.
Conservative label retention
E.
Downstream on demand.
Answer: B
Explanation:
QUESTION NO: 48
Which of the following commands is used to display the database containing the OSPF-TE LSAs?
A.
show router ospf opaque-database
B.
show router ospf database
C.
show router ospf opaque-Isa
D.
show router ospf te opaque
Answer: A
Explanation:
QUESTION NO: 49
Which of the following statements regarding LSPs are true? (Choose two)
A.
IGP-based LSPs are established solely from information contained in routing tables.
C.
The constraint-based routed LSP is calculated at each hop of the LSP, based on the route table
and user defined constraints.
D.
IGP-based LSPs must use LDP signaling.
Answer: A,B
Explanation:
QUESTION NO: 50
Which of the following statements regarding LDP-over-RSVP are true? (Choose two)
A.
Targeted sessions must exist between all routers in the tunnel's path.
B.
Each LDP interface must be configured to support LDP tunneling.
C.
LDP prefixes resolve to an RSVP LSP, rather than to a physical egress interface.
D.
RSVP LSPs must exist between each PE-ABR pair, or ABR-ABR pair in each area.
Answer: C,D
Explanation:
QUESTION NO: 51
Given the configuration shown, how much of a link's 100Mbps reservable bandwidth can an LSP
access when configured for class-type 0 and priority 1?
A.
10Mbps
B.
20Mbps
C.
30Mpbs
D.
60Mbps
E.
70Mbps
Answer: E
Explanation:
QUESTION NO: 52
A.
It uses a UDP connection with an arbitrary port number.
B.
C.
It uses a TCP connection with an arbitrary port number.
D.
It uses a TCP connection with well known port number 646.
Answer: D
Explanation:
QUESTION NO: 53
Which fields in this output uniquely identify the RSVP session belonging to a single LSP? (Choose
three)
A.
Tunnel ID
B.
Name
C.
LSP ID
D.
To
Answer: A,B,C
Explanation:
QUESTION NO: 54
How many bits of the MPLS header are used for the label field?
A.
16
B.
20
C.
24
D.
25
E.
32
Answer: B
Explanation:
QUESTION NO: 55
A.
A mechanism that implements opaque LSAs.
B.
A mechanism that computes routes based on defined user requirements.
C.
A mechanism that allows the IGP shortest path to be used.
D.
A mechanism that allows RSVP or LDP signaling to use a route other than the IGP best route to
establish a LSP.
Answer: B
Explanation:
QUESTION NO: 56
A targeted-LDP session may exist between directly connected or non-directly connected devices
A.
TRUE
B.
FALSE
Answer: A
Explanation:
QUESTION NO: 57
On a point-to-point link, two directly connected routers set different interface hello timeout values.
Router R1 uses 15 seconds, while router R2 uses 30 seconds. What happens to the LDP
adjacency?
A.
The adjacency forms with the lower timeout value
B.
The "show router Idp session" command output displays the adjacency in state "init"
C.
The adjacency forms with the higher timeout value
D.
The adjacency times out after 30 seconds
Answer: A
Explanation:
QUESTION NO: 58
Router R4 originates 500 RSVP signaled LSPs with default hello and refresh timer settings If the
only downstream communication fails (link is operationally UP), how long will RSVP wait before it
A.
3000ms
B.
9000ms
C.
30000ms
D.
120000ms
Answer: B
Explanation:
QUESTION NO: 59
LSP "toR8-5" requests fast reroute protection on the primary loose path. What could be done to
remove the Failure Code shown?
A.
CSPF must be enabled at head-end on fast reroute protected loose path LSPs
B.
Fast reroute must first be enabled on the downstream routers.
C.
CSPF must be enabled on all downstream loose hop routers.
D.
Global revertive path optimization must be enabled so the path will be re-optimized around a failed
node.
Answer: A
Explanation:
QUESTION NO: 60
"Pass Any Exam. Any Time." - www.actualtests.com 37
Nokia 4A0-103 Exam
Click on the exhibit button below.
If the four LSPs shown use the shared-explicit reservation style, how much bandwidth does CSPF
request across a single 1Gbps link?
A.
100Mbps
B.
200Mbps
C.
300Mpbs
D.
"Pass Any Exam. Any Time." - www.actualtests.com 38
Nokia 4A0-103 Exam
600Mbps
E.
700Mbps
Answer: E
Explanation:
Topic 2, Volume B
QUESTION NO: 61
Which of the following statements regarding the MPLS SWAP label operation is true?
A.
The inner label will be exchanged with the MPLS outer label.
B.
The inner label will be exchanged for a new label.
C.
The outer label will be exchanged for a new label.
D.
All labels will be exchanged for one new label.
E.
All labels will be exchanged for an equal number of new labels.
Answer: C
Explanation:
QUESTION NO: 62
If the destination IP address of a received unlabeled packet is successfully matched in the FIB,
which of the following statements are true? Choose two answers.
A.
A PUSH label stack operation must be performed.
B.
The outgoing interface and next-hop address will be determined from the FIB.
"Pass Any Exam. Any Time." - www.actualtests.com 39
Nokia 4A0-103 Exam
C.
The packet can be forwarded as a labeled or unlabeled packet.
D.
A POP label stack operation may be performed.
Answer: B,C
Explanation:
QUESTION NO: 63
Which of the following devices receives labeled packets from the MPLS domain, removes the
MPLS header, and forwards unlabeled packets outside the MPLS domain?
A.
P router
B.
LSR
C.
eLER
D.
iLER
Answer: C
Explanation:
QUESTION NO: 64
A.
Selected labels from the FIB are populated to the LIB.
B.
Selected labels from the LIB are populated to the LFIB.
C.
Selected routes from the RIB are populated to the FIB.
E.
All labels from the LIB are populated to the LFIB.
Answer: B,C
Explanation:
QUESTION NO: 65
When a device receives a labeled packet, which of the following can occur?
A.
The packet can only be forwarded as an unlabeled packet.
B.
The packet can be forwarded as a labeled or unlabeled packet, depending on the received label
value.
C.
The packet can be forwarded as a labeled or unlabeled packet, depending on the destination IP
address in the payload
D.
The packet can only be forwarded as a labeled packet.
Answer: B
Explanation:
QUESTION NO: 66
Which of the following describes what happens when facility backup fast reroute is enabled for a
LSP? Choose three answers.
A.
Each PLR will signal a bypass tunnel that avoids the next-hop node or link.
B.
When a failure occurs, the PLR will push an additional label onto the label stack and start
forwarding traffic onto its bypass tunnel.
"Pass Any Exam. Any Time." - www.actualtests.com 41
Nokia 4A0-103 Exam
C.
The ingress router will include a RRO object in the path message to indicate the routers that
should be PLRs and MPs along the protected path.
D.
The ingress router will set the local protection desired flag in the session attribute object of the
path message to inform all routers along the protected LSP path to establish bypass tunnels.
E.
When the bypass tunnel is in use, the MP will include the RRO object in its PathErr message, with
the local protection in use flag set to notify the ingress router that it is using the bypass tunnel.
Answer: A,B,D
Explanation:
QUESTION NO: 67
True or False? MPLS may use an existing data link layer header field to identify a label, instead of
using a specific MPLS header
A.
TRUE
B.
FALSE
Answer: A
Explanation:
QUESTION NO: 68
Which one of the following statements regarding the detour object transported in the detour path
message is true?
A.
The PLR sends it downstream with the RRO.
B.
The PLR sends it downstream with the ERO.
C.
"Pass Any Exam. Any Time." - www.actualtests.com 42
Nokia 4A0-103 Exam
It associates all detours with the source PLR.
D.
The MP sends it upstream with the RESV message.
Answer: B
Explanation:
QUESTION NO: 69
What MPLS function should be performed by a router that receives a data packet containing an
MPLS label value of 3?
A.
A router will never receive a packet containing this label value.
B.
Request a new label from the peer that provided this label.
C.
Pop the label.
D.
PUSH an additional label onto the label stack.
E.
Signal a new label to the peer that sent the packet.
Answer: A
Explanation:
QUESTION NO: 70
Which of the following is described by the following statement? An LSR propagates a label
mapping only for an FEC for which it has a label mapping for the FEC next-hop.
A.
Independent control mode.
B.
Ordered control mode.
D.
Conservative label retention.
E.
Downstream on demand
Answer: B
Explanation:
QUESTION NO: 71
Which of the following statements regarding per-platform label space are true? Choose two
answers.
A.
A separate label is used for each interface that the FEC is advertised on.
B.
It uses fewer label resources than a per-interface label space.
C.
It is typically used when the device has ATM or Frame Relay interfaces.
D.
It uses more label resources than a per-interface label space.
E.
A single label may be assigned to an FEC and used across all interfaces of the same router.
F.
It is only valid when the LDP peers are directly connected over an interface, and the label is only
going to be used for traffic sent over that interface.
Answer: B,E
Explanation:
QUESTION NO: 72
Which of the following can be used for label signaling and distribution on the Alcatel-Lucent 7750
"Pass Any Exam. Any Time." - www.actualtests.com 44
Nokia 4A0-103 Exam
SR? Choose two answers
A.
RSVP-TE
B.
TDP
C.
LDP
D.
ADP
E.
MPLS-TE
Answer: A,C
Explanation:
QUESTION NO: 73
Which of the following are top level TLV types defined for OSPF-TE? Choose two answers.
A.
Router address
B.
Traffic engineering metric
C.
Maximum bandwidth
D.
Link
E.
Admin Group
Answer: A,D
Explanation:
A.
Static LSPs
B.
Reserved use
C.
Vendor proprietary use
D.
Management LSPs
E.
Dynamic LSPs
Answer: B
Explanation:
QUESTION NO: 75
Which of the following are characteristics of ECMP LSPs in LDP? Choose three answers
A.
Liberal label retention mode
B.
T-LDP enabled with peers to which load balancing is desired.
C.
ECMP enabled in the config>router context.
D.
Hashing used to select the egress label.
E.
Export policy applied to advertise multiple labels for a given FEC.
Answer: A,C,E
Explanation:
QUESTION NO: 76
LDP is enabled on both ends of a point-to-point link, but the "show router Idp status" command
indicates that LDP is operationally down. The Oper Down Reason field shows the message
"systemIpDown." What might cause this condition?
A.
The LSP is in the administrative down state.
B.
The router's router ID overlaps another.
C.
The router's interfaces do not have LDP running.
D.
The router's system interface requires an IP address
Answer: D
Explanation:
QUESTION NO: 77
The policy on router R2 is applied as an LDP export policy. What FECs now appear in router R2's
LIB?
A.
Local FECs, not including those in the 192.168.1.0/24 address space.
B.
Only system ID FECs may appear in the LIB.
C.
Any local FECs, except those with a 24 bit mask.
D.
Local FECs in the 192.168.1.0/24 address space
Answer: A
Explanation:
QUESTION NO: 78
B.
By eliminating the requirement for core IP routing.
C.
By not allowing more than one LSP to use a particular path.
D.
By defining multiple LSPs across a network and implementing an IGP load balancing algorithm
across them.
Answer: A
Explanation:
QUESTION NO: 79
Consider the output shown; why is the label in bold font not in use?
A.
The router cannot do a SWAP of this label.
B.
The label does not match the egress label for the same FEC.
C.
D.
The label was signaled in error.
Answer: C
Explanation:
QUESTION NO: 80
Which of the following timers can be adjusted to reduce the time a router waits between attempts
to re-establish an LSP after it has failed?
A.
Isp retry-timer
B.
Isp retry-limit
C.
mpls resignal-timer
D.
rsvp refresh-time
E.
router rsvp keep-multiplier
Answer: A
Explanation:
QUESTION NO: 81
Which of the following LDP messages are used in the successful establishment of LDP sessions?
Choose three answers
A.
Label request message
B.
Notification message
D.
Keepalive message
E.
Initialization message
F.
Hello message
Answer: D,E,F
Explanation:
QUESTION NO: 82
A.
RIB
B.
FIB
C.
LIB
Answer: D
Explanation:
QUESTION NO: 83
If the original LSP already has two labels, and router R2 has failed, how many labels will there be
in packets on the detour path?
A.
1
B.
2
C.
3
D.
4
"Pass Any Exam. Any Time." - www.actualtests.com 52
Nokia 4A0-103 Exam
Answer: B
Explanation:
QUESTION NO: 84
Under which condition might the peer LDP ID 10.10.10.2:0 entry show state "Nonexistent"?
A.
When the interface to the peer router is down.
B.
When router R1 has no route to the peer address 10.10.10.2.
C.
When the adjacency between the two routers fails.
D.
When the targeted session is not yet configured.
Answer: B
Explanation:
QUESTION NO: 85
- Bidirectional LDP-over-RSVP tunnels extend from routers R1 to R3 and back over the path R1-
R4-R5-R3.
- You enable fast reroute facility bypass on the R5-R3 RSVP LSP.
- Router R5 acts as a PLR, protecting the R5-R3 link by building a bypass tunnel through router
R2.
You build a layer 2 VPN on routers R1 and R3, using the LDP-over-RSVP tunnels. What MPLS
configuration step must you complete on router R2 for it to protect the end-to-end service?
A.
Enable LDP on the R2-R5 interface.
B.
Configure T-LDP sessions between routers R2 and R5 and R3.
C.
Configure LDP-over-RSVP support on router R2.
D.
Enable MPLS and RSVP on the router R2 network interfaces.
E.
Enable LDP on the R2-R5 and R2-R3 interfaces.
Answer: D
Explanation:
QUESTION NO: 86
Which of the following configurations allow a router to periodically attempt to move LSP traffic to a
better path, if the head end can find one?
A.
configure router mpls retry-timer 30
B.
configure router mpls resignal-timer 30
C.
configure router mpls retry-attempts 30
D.
configure router mpls global-revertive 30
Answer: B
Explanation:
QUESTION NO: 87
Which one of the following statements regarding RSVP LSP configuration is true?
A.
LSPs must always terminate on a system ID.
B.
MPLS and RSVP must be enabled on all routers.
C.
Interfaces must be individually created in RSVP.
D.
Path definitions must include at least one hop entry.
Answer: B
Explanation:
Which of the following conditions must a router meet for an LSP path's RSVP session to exist?
Choose two answers
A.
The router must build the Path State Block (PSB).
B.
The router must build the Reservation State Block (RSB).
C.
The router must build the Session State Block (SSB)
D.
The router must send the second RESV refresh message.
E.
The router must receive the second PATH refresh message.
Answer: A,B
Explanation:
QUESTION NO: 89
A.
IP routing protocols do not always select the best route to a destination.
B.
IP routing protocols always select multiple routes to a destination.
C.
IP routing protocols do not make use of all available network attributes to select a path
D.
Improper network design results in limited network path redundancy.
Answer: C
Explanation:
Given the configuration below, which of the following commands would enable fast reroute on the
LSP? Choose two answers
A.
This configuration already is configured for FRR.
B.
fast-reroute facility
C.
fast-reroute one-to-one
D.
secondary <name>
E.
"Pass Any Exam. Any Time." - www.actualtests.com 57
Nokia 4A0-103 Exam
standby
Answer: B,C
Explanation:
QUESTION NO: 91
LSP 1's link between routers R3 and R6 has failed, and the RESV state at router R3 has timed
out. Which of the following actions will router R3 initiate?
A.
Send a Path Tear message towards router R6.
B.
Send a Path Tear message towards router R1.
C.
Send a Resv Tear message toward router R6.
D.
Send a Resv Tear message toward router R1.
Answer: D
Explanation:
QUESTION NO: 92
A.
It supports IGP-based LSPs.
B.
It supports constrained path LSPs.
C.
It does not support loose explicit path LSPs.
D.
It is recommended for use in Traffic Engineering applications.
E.
It cannot be used with facility backup fast reroute.
Answer: A,B,D
Explanation:
QUESTION NO: 93
Router R3 signals an LSP, reserving 1Gbps bandwidth on a 10Gbps link. RSVP configuration
limits reservable bandwidth to 20 percent on the egress interface. Which of the following
statements is true?
A.
The egress RSVP interface has 80 percent bandwidth unreserved.
B.
LSPs can reserve an additional 9.9 Gbps bandwidth on this RSVP interface.
C.
The head end reserves 100Mbps for the LSP.
D.
The egress RSVP interface has 1Gbps bandwidth unreserved.
Answer: D
QUESTION NO: 94
A.
TE enabled OSPF routers
B.
Backbone router only
C.
ABR only
D.
ASBR only
Answer: A
Explanation:
QUESTION NO: 95
A.
Admin groups can be configured using the command "configure>router>mpls>admin-group".
B.
CSPF uses the information defined by admin groups when paths are computed for constraint-
based LSPs.
C.
By default, interfaces for which MPLS has been enabled are in the default admin group.
D.
A LSP can make use of admin groups for constraint-based path calculations by including or
excluding the admin group
Answer: C
QUESTION NO: 96
A.
Type 9 LSA ?Link local LSA
B.
Type 10 LSA ?Area local LSA
C.
Type 8 LSA ?TE router LSA
D.
Type 11 LSA ?Network LSA
Answer: B
Explanation:
QUESTION NO: 97
A.
By defining new LSAs for the IS-IS protocol.
B.
By utilizing the OSPF opaque LSAs to maintain interoperability with OSPF routing domains
C.
By defining new TE extension TLVs to the IS-IS protocol.
D.
By enabling CSPF algorithm extensions that allow link state TE to be implemented.
Answer: C
Explanation:
QUESTION NO: 98
The destination IP address of a received unlabeled packet is successfully matched in the FIB.
A.
A POP label stack operation may be performed.
B.
The outgoing interface and next-hop address will be determined from the FIB.
C.
The packet can be forwarded as a labeled or unlabeled packet.
D.
A PUSH label stack operation may be performed.
Answer: A
Explanation:
QUESTION NO: 99
Fill in the blanks: The device at the beginning of an LSP is referred to as the_________, and the
device at the end of an LSP is referred to as the ___________.
A.
PE, P
B.
LER, LSR
C.
LSR, LER
D.
iLER, eLER
E.
eLER, iLER
F.
Answer: D
Explanation:
A.
To establish additional LSPs across the network
B.
To allow ECMP to occur across an MPLS network
C.
To enable the implementation of services
D.
To utilize paths other than the lowest cost path
Answer: D
Explanation:
A.
A single label is assigned to a FEC for all interfaces on the same router.
B.
The same label can be used to forward a packet on an LSR regardless of which egress port is
used.
C.
It uses fewer label resources than a per-platform label space.
D.
A separate label is used for each interface that the FEC is advertised on.
A.
Each implementation can use it as they see fit.
B.
It is used to carry the Ether type value.
C.
It is used to carry the TTL value.
D.
It is used to carry QoS classification.
E.
It is used to carry fragmentation flag information.
Answer: D
Explanation:
An Alcatel-Lucent 7750 SR label switches a packet it receives. The packet has an outer label TTL
of 250 and an inner label TTL of 251. Which of the following is TRUE?
A.
The outer label TTL will be 249 and the inner label TTL will be 250.
B.
The outer label TTL will be 249 and the inner label TTL will be 251.
C.
The outer label TTL will be 251 and the inner label TTL will be 251.
D.
The outer label TTL will be 251 and the inner label TTL will be 252.
Which mode does the following statement describe? An LSR will advertise a label mapping
immediately, without waiting for a label mapping from the FEC's next-hop.
A.
Liberal label retention mode
B.
Conservative label retention mode
C.
Ordered control mode
D.
Independent control mode
Answer: D
Explanation:
A.
RSVP-TE is a routing protocol.
B.
RSVP-TE requests end-to-end resources for unidirectional data flow.
C.
RSVP-TE consults the local RSVP database to determine the path from source to destination.
D.
RSVP-TE generates a TED for storing traffic engineering information.
Answer: B
A.
The customer's Layer 2 header is preserved at the iLER for Layer 2 services.
B.
The customer's Layer 2 Header is preserved at the iLER for Layer 3 services.
C.
The service provider's Layer 2 header is added at the iLER for Layer 2 services.
D.
The service provider's Layer 2 header is added at the iLER for Layer 3 services.
Answer: B
Explanation:
What action does a router perform when it looks up the label of an incoming packet in its LFIB and
sees that the LFIB maps to an egress label of 3?
A.
It requests a new label from the peer that provided this label.
B.
It pops the label.
C.
It pushes an additional label onto the label stack.
D.
It signals a new label to the peer that sent the packet.
Answer: B
Explanation:
Under which condition might the peer entry with an LDP ID of 10.10.10.2:0 show the state
"Nonexistent"?
A.
When the interface to the peer router is down.
B.
When router R1 has no route to the peer address 10.10.10.2.
C.
When LDP is not configured on the peer router's interface.
D.
When the targeted session is not configured.
Answer: B
Explanation:
A.
A packet arriving with label 131066 will be forwarded out interface 1 /1 /4 with label 131070.
B.
The router is an egress router for FEC 10.10.10.221/32.
C.
There are multiple LSPs to reach FEC 10.10.10.244/32.
D.
The router's system address is 10.10.10.242/32.
Answer: D
Explanation:
Which of the following about Alcatel-Lucent 7750 SR command "oam Isp-trace prefix" is FALSE?
A.
The router performs a unidirectional LSP test.
B.
"Pass Any Exam. Any Time." - www.actualtests.com 68
Nokia 4A0-103 Exam
The router collects hop information along the tunnel's path.
C.
The router uses MPLS Echo Request packets that are IP-routed,
D.
The MPLS TTL values are incremented at each request.
Answer: C
Explanation:
Router R2 advertises an OSPF summary route 10.10.10.0/24 into Area 1. Router R3 receives
labels for individual FECs 10.10.10.2/32 and 10.10.10.4/32. These two FECs are installed in router
R3's LIB but not in the LFIB. What needs to be done on router R3 to install these labels into its
LFIB?
A.
Disable route summarization on router R3.
B.
Enable LDP aggregate prefix match.
C.
Create an import policy to accept 10.10.10.2/32 and 10.10.10.4/32.
D.
Disable LDP exact match on 10.10.10.2/32 and 10.10.10.4/32.
"Pass Any Exam. Any Time." - www.actualtests.com 69
Nokia 4A0-103 Exam
Answer: B
Explanation:
This policy is applied as an LDP export policy. In addition to the FECs learned from its neighbors,
which FECs now appear in the router's LIB?
A.
Local FECs not included in the 192.168.1.0/24 address space and the system IP FEC.
B.
Only the system IP FEC appears in the LIB.
C.
Any local FECs, except those with a 24-bit mask.
D.
Local FECs in the 192.168.1.0/24 address space.
Answer: A
Explanation:
Which of the following are the default settings for the Alcatel-Lucent 7750 SR when using LDP?
A.
Per-platform label space, conservative retention mode
B.
Per-interface label space, conservative retention mode
C.
Per-platform label space, liberal retention mode
D.
Per-interface label space, liberal retention mode
Answer: C
Explanation:
A.
Link-based and T-LDP sessions may be configured on the same LSR.
B.
T-LDP supports sessions between non-directly connected devices.
C.
T-LDP can be configured between directly connected devices.
D.
T-LDP Hello messages are sent to a multicast address.
Answer: D
Explanation:
A.
Notification
B.
Session
C.
Discovery
D.
Advertisement
Answer: C
Explanation:
Two directly connected routers set different interface Hello timeout values. Router R1 uses 15
seconds, while router R2 uses 30 seconds. Which of the following best describes the LDP
adjacency?
A.
The adjacency forms with the lower timeout value.
B.
The adjacency forms with the higher timeout value.
C.
The adjacency is in init state.
D.
The adjacency times out after 30 seconds.
Answer: A
Explanation:
An Alcatel-Lucent 7750 SR enabled with LDP has multiple equal cost paths to a given FEC. After
A.
The router has new entries added for the given FEC in its LIB.
B.
The router has new entries added for the given FEC in its FIB.
C.
The router generates a single label for the given FEC and advertises it to all its peers,
D.
The router has multiple LSP tunnels for the given FEC.
Answer: A
Explanation:
A.
The Hello protocol can speed up convergence without reducing refresh time.
B.
Hello messages are sent after at least one RSVP session is active on the interface.
C.
An interface with multiple RSVP sessions sends Hello messages for each session.
D.
An RSVP neighbor is declared down if Hello messages are not received within the Hello timeout.
Answer: C
Explanation:
Which of the following describes how a router sets the destination IP address for an RSVP RESV
message?
B.
It sets the address to the next upstream hop from the ERO.
C.
It sets the address to the next upstream hop from the PSB.
D.
It sets the address to the next upstream hop from the RRO.
Answer: C
Explanation:
A.
Label bindings are distributed to other routers when explicitly requested.
B.
Label bindings are distributed to all neighbors including non-downstream routers.
C.
Label bindings are distributed if labels have not been received from downstream routers.
D.
All labels received from downstream neighbors are stored in the LIB.
Answer: A
Explanation:
Topic 3, Volume C
RSVP state for LSP 1 has timed out on router R3. Which of the following actions will router R3
initiate to clear the RSVP session?
A.
Send a RESV Tear message toward router R6.
B.
Send a RESV Tear message toward router R1.
C.
Send a RESV Error message toward router R6.
D.
Send a RESV Error message toward router R1.
Answer: B
Explanation:
Which of the following about the Alcatel-Lucent 7750 SR command "own Isp-trace" is FALSE?
A.
The MPLS TTL values are incremented at each request.
B.
The router uses MPLS Echo Request packets that are IP-routed.
C.
The router collects hop information along the tunnel's path.
"Pass Any Exam. Any Time." - www.actualtests.com 75
Nokia 4A0-103 Exam
D.
The router performs an unidirectional LSP test.
Answer: B
Explanation:
Initially, all links have 800Mbps of unreserved bandwidth. All links are of equal costs. Shared
explicit reservation style is used. LSP 1 is signaled first with a setup and hold priority of 2. Then,
LSP 2 is signaled with setup and hold priority of 5. Both LSPs go from R1 to R5. Which of the
following is TRUE?
A.
LSP 1 will follow R1-R3-R4-R5. LSP 2 will follow R1-R2-R5.
B.
LSP1 will follow R1-R2-R5. LSP 2 will follow R1-R3-R4-R5.
C.
Both LSP 1 and LSP 2 will follow R1-R2-R5.
D.
Both LSP 1 and LSP 2 will follow R1-R3-R4-R5.
A.
RSVP LSPs must exist between each PE-ABR pair, or ABR-ABR pair in each area.
B.
When LDP-over-RSVP is active, the LDP prefixes are resolved to a physical egress interface.
C.
Targeted sessions must exist between all routers along the tunnel path.
D.
Link LDP sessions must exist between each ABR-ABR pair in each area.
Answer: A
Explanation:
A.
CAC is used when the LSP path has not been computed by CSPF.
B.
CAC is used when the LSP path has been computed by CSPF.
C.
CAC is used to perform a bandwidth check on each egress interface of the downstream router.
D.
CAC is used to perform a bandwidth check based on the router's LSDB.
Answer: D
Explanation:
The link between routers R4 and R6 is down before the LSP is signaled. CSPF is enabled on the
LSP. Which of the following conditions is TRUE?
A.
Router R1 sends a PATH message and router R4 sends back a PATH Error message.
B.
Router R1 does not send a PATH message because it detects an error.
C.
Router R1 sends a PATH message and router R4 sends back a PATH Tear message.
D.
Router R1 sends a PATH message and router R4 sends back a RESV Error message.
Answer: B
Explanation:
Which of the following is NOT an advantage of MPLS shortcuts for BGP traffic?
B.
It eliminates double route lookups on all routers within an AS.
C.
It eliminates the need to run IGP on all routers within an AS.
D.
It eliminates the need for an iBGP full mesh on all core routers.
Answer: C
Explanation:
Which of the following about configuring an LSP path definition on an Alcatel-Lucent 7750 SR is
FALSE?
A.
A path definition can have both loose and strict hops.
B.
A path definition can be configured with loose hops only.
C.
A path definition is configured on the head-end router only,
D.
A path definition is not required if CSPF is enabled on an LSP.
Answer: D
Explanation:
A router has two admin groups defined (GREEN=1 and RED=3). An interface is associated to both
admin groups. What value will be shown in the Admin Group sub-TLV for this interface?
A.
B.
0x5
C.
0x10
D.
0xa
Answer: D
Explanation:
Which of the following about Link TLVs found inside Type 10 Opaque LSAs is FALSE?
A.
Link TLVs are used to advertise administrative group information.
B.
Link TLVs are exchanged once RSVP is enabled on the interfaces.
C.
Link TLVs are used to advertise router-IDs.
D.
Link TLVs are used to advertise bandwidth information.
Answer: C
Explanation:
Initially, all links along the path R1-R2-R4-R6 have 400Mbps unreserved bandwidth and all links
along the path R1-R3-R5-R6 have 800Mbps unreserved bandwidth. Shared Explicit reservation
style is used and Make-Before-Break is enabled. Both fully loose LSPs have been signaled as
shown. Later, the configured bandwidth for LSP-1 is changed to 400Mbps. Which of the following
is TRUE?
A.
After a new path for LSP-1 is established on R1-R3-R5-R6, the old path is torn down.
B.
After the old path for LSP-1 is torn down, the new path is established on R1-R3-R5-R6.
C.
LSP-1 will stay on R1-R2-R4-R6 because there is enough bandwidth on the existing path.
D.
LSP-1 will be torn down because CSPF fails to find a new path.
Answer: C
Explanation:
A.
A mechanism that implements opaque LSAs.
C.
A mechanism that ensures the IGP best route is used.
D.
A mechanism that enables LDP signaling to use a route other than the IGP best route.
Answer: B
Explanation:
A.
Configure BGP with the IPv6 address family.
B.
Configure BGP to add IPv6 Explicit Null labels.
C.
Configure a route policy to export IPv6 routes into BGP.
D.
Configure the nexthop core router as a BGP peer.
Answer: D
Explanation:
All links have 1Gbps unreserved bandwidth initially and Shared Explicit reservation style is used.
After the LSP's primary and standby secondary paths are signaled, how much unreserved
bandwidth is left on the links?
A.
R1-R2 will have 300Mbps left and R2-R4 will have 400Mbps left.
B.
R1-R2 will have 400Mbps left and R2-R4 will have 400Mbps left.
C.
R1-R2 will have 600Mbps left and R2-R4 will have 600Mbps left.
D.
R1-R2 will have 300Mbps left and R2-R4 will have 600Mbps left.
Answer: C
Explanation:
A.
IGP-based LSPs are calculated based on information contained in routing tables.
B.
Constraint-based LSPs are calculated using the head-end router's TED.
D.
IGP-based LSPs must use LDP signaling.
Answer: D
Explanation:
All links have 1Gbps unreserved bandwidth initially and all LSPs have the least-fill feature
enabled. After the two LSPs have been signaled as shown, two new LSPs are configured. LSP-3
is signaled first with 600Mbps reserved. LSP-4 is signaled after with 800Mbps reserved. All LSPs
have the same setup and hold priorities. Which paths will CSPF choose for LSP-3 and LSP-4?
A.
LSP-3 takes R1-R3-R5-R6 and LSP-4 takes R1-R2-R4-R6.
B.
LSP-3 takes R1-R2-R4-R6 and LSP-4 takes R1-R3-R5-R6.
C.
LSP-3 takes R1-R3-R5-R6 and LSP-4 has no available path.
D.
LSP-3 takes R1-R2-R4-R6 and LSP-4 has no available path.
Answer: C
Explanation:
An LDP-over-RSVP tunnel is established between routers R1 and R6. There is a VPN service
running between routers R1 and R6. Which of the following is TRUE?
A.
Router R4 swaps both the RSVP-TE LSP label and LDP transport label received with new labels,
B.
Router R4 swaps the VPN service label received with a new label.
C.
Router R4 uses the same RSVP-TE LSP label as the one received from router R3.
D.
Router R4 uses the same LDP transport label as the one received from router R3.
Answer: A
Explanation:
An LSP is enabled with one-to-one fast reroute and node protection. What action does the PLR
take if node protection cannot be provided?
A.
The PLR attempts to provide link protection.
B.
The PLR disregards the request after three failed attempts.
C.
The PLR changes the PATH message to request link protection.
D.
The PLR brings down the primary LSP-path.
An LSP traverses the path R1-R2-R3-R6 and facility fast reroute is enabled. If the protected LSP
carries one transport label and one service label, how many labels will be on the bypass tunnel if
router R2 fails?
A.
1
B.
2
C.
3
D.
4
Answer: C
Explanation:
B.
Fast reroute provides path protection close to the failure point.
C.
Fast reroute provides fast failure detection to the head-end router.
D.
Fast reroute protects both primary and secondary paths.
Answer: B
Explanation:
An LDP tunnel is established on R1-R2-R4-R6 because the link between routers R3 and R6 is
down. With the LDP-IGP Sync feature enabled and after the link is restored, which of the following
is FALSE?
A.
Router R3 starts the LDP-Sync timer after recovering the LDP session on R3-R6.
B.
Router R1 continues to use R1-R2-R4-R6 until the LDP-Sync feature is disabled.
D.
Router R1 receives a label from router R3 after the LDP session is established on R3-R6.
Answer: B
Explanation:
Using facility mode fast reroute, how does the PLR learn the address of the MP?
A.
The PLR issues an RSVP PATH message to the tail-end requesting the address of the MP.
B.
The PLR learns the address of the MP from the ERO.
C.
The PLR learns the address of the MP from the RRO.
D.
The PLR learns the address of the MP from the targeted RSVP Hello message.
E.
The PLR knows the address of the MP is the same as the tail-end router.
Answer: C
Explanation:
An LSP path is established on router R1 toward router R6. After router R4 detects that the link
between routers R4 and R6 goes down, which of the following will affect the failure propagation
time?
A.
The time router R4 takes to send a PATH Error message toward the head-end router.
B.
The time router R4 takes to detect RSVP Hello message timeout from router R6.
C.
The time router R4 takes to send a RESV Error message to the head-end router.
D.
The time router R1 takes to signal an alternate path through router R3.
Answer: A
Explanation:
An LSP traverses R1-R2-R4-R6 and facility fast reroute with link protection is enabled. All links
have the same cost. Which of the following about PLRs and MPs is TRUE?
A.
R1, R2, and R4 can be PLRs; R6 is the MP.
B.
R1, R2, and R4 can be PLRs; R2, R4, and R6 are MPs.
C.
R1, R2, R3, R4, and R5 can be PLRs; R6 is the MP.
D.
R1, R2, R3. R4, and R5 can be PLRs; R2, R4, and R6 is the MP.
Answer: B
Explanation:
A.
The router 10.10.10.1 is a PLR providing node protection for the router 10.10.10.3.
B.
One-to-one fast reroute protection is requested by an LSP.
C.
The bypass-link tunnel is used to avoid the link with the egress interface address 10.3.4.4.
D.
The bypass-node tunnel is used to avoid the next-hop downstream router 10.10.10.3.
Answer: B
Explanation:
All links are operationally up initially. When the link between routers R4 and R6 goes down, what
will router R1 do?
A.
Router R1 will switch traffic to the secondary path immediately.
B.
Router R1 will discard traffic until a new IGP route to router R6 is re-calculated.
C.
Router R1 will discard traffic because the secondary path is not a fully strict path.
D.
Router R1 will signal the secondary path and switch traffic to it.
Answer: D
Explanation:
All links are of equal cost. A CSPF-enabled LSP is configured on R1 to R6. Its fully loose primary
path is configured with an "include green" statement and the fully loose secondary path is
configured with an "include red" statement.
A.
No primary path is established. The secondary path will take R1-R2-R4-R6.
B.
The primary path will take R1-R3-R5-R6. The secondary path will take R1-R2-R4-R6.
C.
The primary path will take R1-R2-R4-R6. No secondary path is established.
D.
The primary path will take R1-R2-R4-R6. The secondary path will take R1-R3-R5-R6.
Answer: C
Explanation:
Which of the following about an LSP protected with one-to-one FRR is TRUE?
A.
The LSP can use facility and one-to-one FRR simultaneously.
B.
The LSP is limited to node protection.
C.
A single protection tunnel is used for all LSPs with the same path.
D.
A detour protection tunnel is created for the LSP.
Answer: D
Explanation:
Both Path-1 and Path-2 are down. If Path-2 becomes available again, how does the headend
router select the secondary LSP path?
A.
The router will switch to Path-2 because it is the first secondary path configured in the list.
B.
The router will not switch to Path-2 because the current path has the longest uptime.
C.
The router will switch to Path-2 because it is a more preferred path.
D.
The router will not switch to Path-2 because the router will not revert to another secondary path.
Answer: C
Explanation:
A fully loose LSP "toR6" is enabled with FRR protection. All links have the same cost. After the link
between R2 and R4 goes down, FRR protection repairs the LSP and traffic traverses on R1-R2-
R7-R8-R4-R6. Which of the following about this CSPF-enabled LSP on an Alcatel-Lucent 7750 SR
is TRUE?
A.
The LSP will stay on the current path indefinitely unless another failure occurs.
B.
The LSP will stay on the current path until the resignal timer expires.
C.
The LSP will switchover to R1-R2-R3-R5-R6 after the resignal timer expires.
D.
The LSP will switchover to R1-R3-R5-R6 after the retry timer expires.
Answer: D
Explanation:
Which of the following regarding the MPLS SWAP label operation is TRUE?
A.
The inner label will be exchanged with the MPLS outer label.
B.
The inner label will be exchanged for a new label.
C.
The outer label will be exchanged for a new label.
D.
All labels will be exchanged for one new label.
E.
All labels will be exchanged for an equal number of new labels.
Answer: C
Explanation:
A.
Label swapping
B.
Pushing a label on an unlabeled packet
C.
Label allocation
D.
Routing lookups
Answer: C
Explanation:
A.
An LSR may answer requests for label mappings immediately, without waiting for a label mapping
from the next-hop.
B.
An LSR may advertise label mappings to all peers for which it might be a next-hop for a given
FEC.
C.
An LSR propagates a label mapping downstream for a FEC, only if it has a label mapping for the
FEC next-hop.
D.
An LSR will only distribute a label for a FEC when it has been requested to do so.
Answer: B
Explanation:
A.
T-LDP is used to provide an end-to-end session between two PE routers.
B.
T-LDP is used to signal service labels for Layer 2 services.
C.
T-LDP is used to establish transport tunnels for Layer 2 services.
D.
T-LDP is used in LDP over RSVP solution.
Answer: C
Explanation:
Which mode does the following statement describe? An LSR will advertise a label mapping
immediately, without waiting for a label mapping from the FEC's next-hop.
A.
Liberal label retention mode
B.
Conservative label retention mode
C.
Ordered control mode
D.
Independent control mode
Answer: D
Explanation:
What MPLS function should be performed by a router that receives a data packet with an MPLS
label value of 0?
A.
Push an additional label onto the label stack.
B.
Pop the label.
C.
Swap the label.
D.
Pop the label and push an additional label onto the label stack.
Answer: B
Explanation:
Router R2 advertises the aggregate prefix 10.10.10.0/24 into Area 1. Why would LDP aggregate-
prefix-match be enabled on router R3?
A.
To reduce the number of LDP sessions
B.
To reduce the number of LIB and LFIB entries
C.
To bypass the LDP exact prefix match rule
D.
To export summarized routes from OSPF to LDP
Answer: C
Explanation:
A.
Label space mode
B.
Label retention
D.
Keepalive factor
Answer: D
Explanation:
A.
It uses a UDP connection with an arbitrary port number.
B.
It uses a UDP connection with well-known port number 646.
C.
It uses a TCP connection with an arbitrary port number.
D.
It uses a TCP connection with well-known port number 646.
Answer: D
Explanation:
This policy is applied as an LDP export policy. In addition to the FECs learned from its neighbors,
which FECs will appear in this router's LIB?
A.
All FECs with a prefix of 192.168.1.0/30.
B.
Local FECs with a prefix of 192.168.1.0/30.
C.
All FECs excluding 192.168.1.0/30.
D.
Local FECs excluding 192.168.1.0/30.
Answer: D
Explanation:
Why might router R2 have a Link LDP session to R1 (10.10.10.1:0) but not to R3 (10.10.10.3:0)?
A.
LDP is not configured on R2.
B.
R2 does not have a route to 10.10.10.3.
C.
LDP is not configured on R3's interface to R2.
D.
The targeted session is not configured on R2.
Answer: C
Explanation:
A.
RSVP-TE supports Connection Admission Control (CAC).
B.
RSVP-TE enables simplified configuration of LSPs.
C.
RSVP-TE supports path calculations that do not use IGP cost.
D.
RSVP-TE provides support for traffic protection features.
Answer: B
An LSP is configured with a fully loose path and CSPF is not enabled. An LSR receives the first
PATH message for this LSP. Which of the following is NOT performed by the LSR?
A.
The LSR regenerates and forwards a new PATH message.
B.
The LSR stores the PATH message in the PSB.
C.
The LSR forwards the PATH message based on the HOP object in the RSB.
D.
The LSR looks up the PATH message's destination IP address in the FIB.
Answer: C
Explanation:
Which of the following about RSVP-TE LSP configuration in a Alcatel-Lucent 7750 SR is TRUE?
A.
LSPs must always terminate on a system ID.
B.
MPLS and RSVP must be enabled on all LSRs.
C.
CSPF must be enabled.
D.
Path definitions must include at least one hop entry.
Answer: B
Explanation:
Which of the following modes are used by RSVP-TE on an Alcatel-Lucent 7750 SR?
A.
Independent control mode, downstream on demand
B.
Independent control mode, downstream unsolicited
C.
Ordered control mode, downstream on demand
D.
Ordered control mode, downstream unsolicited
Answer: C
Explanation:
Which of the following about RSVP refresh reduction on a Alcatel-Lucent 7750 SR is FALSE?
A.
RSVP generates a summary refresh message for each LSP.
B.
Message-IDs replace individual refresh messages.
C.
An LSP state change causes the Message-ID to be incremented.
D.
RSVP refresh reduction is disabled by default.
Answer: A
Explanation:
The link between routers R4 and R6 are configured with an admin group "red". What happens
when the LSP is first signaled?
A.
The LSP will go through the path R1-R2-R4-R6.
B.
The LSP will go through the path R1-R3-R5-R6.
C.
The LSP is down because router R1 detects that no path can meet its constraints.
D.
The LSP is down because router R4 detects that no path can meet its constraints.
Answer: C
Explanation:
All links have 1 Gbps unreserved bandwidth initially. After the LSP's primary and standby
secondary paths are signaled, how much bandwidth is reserved on the link between routers R1
and R2?
A.
If Shared Explicit reservation style is used, 400Mbps is reserved.
B.
If Shared Explicit reservation style is used, 700Mbps is reserved.
C.
If Fixed Filter reservation style is used, 400Mbps is reserved.
D.
If Fixed Filter reservation style is used, 300Mbps is reserved.
Answer: D
Explanation:
An LDP-over-RSVP tunnel is established between routers R1 and R6. There is a VPN service
running between routers R1 and R6. Which of the following is TRUE?
A.
Router R3 swaps both the RSVP-TE LSP label and LDP transport label received with new labels.
B.
Router R3 swaps the VPN service label received with a new label.
C.
Router R3 uses the same RSVP-TE LSP label as the one received from router R2.
D.
Router R3 uses the same LDP transport label as the one received from router R2.
Answer: D
Explanation:
An Alcatel-Lucent 7750 SR has its TE update threshold enabled with the up threshold set to 40%.
The maximum reservable bandwidth on the link is 200M and 30M have already been reserved.
When will a TE update be sent on this link?
A.
When the reserved bandwidth goes above 80M.
B.
When the reserved bandwidth goes above 40M.
C.
When an additional 80M bandwidth is reserved.
D.
When an additional 40M bandwidth is reserved.
Which of the following CANNOT be used to ensure the LSP toR6" will follow the path R1-R2-R4-
R6?
A.
Admin groups
B.
Hop-limit
C.
Strict hops
D.
TE-Metric
Answer: B
Explanation:
All links have 1 Gbps unreserved bandwidth initially and all LSPs have the least-fill feature
enabled. After the two LSPs have been signaled as shown, two additional LSPs are configured.
LSP-3 is signaled first with 50Mbps reserved. LSP-4 is signaled after with 400Mbps reserved.
A.
Both LSP-3 and LSP-4 take R1-R2-R4-R6.
B.
Both LSP-3 and LSP-4 take R1-R3-R5-R6.
C.
LSP-3 takes R1-R3-R5-R6 and LSP-4 takes R1-R2-R4-R6.
D.
LSP-3 takes R1-R2-R4-R6 and LSP-4 takes R1-R3-R5-R6.
E.
CSPF randomly chooses one of the equal cost paths for the two LSPs.
Answer: B
"Pass Any Exam. Any Time." - www.actualtests.com 110
Nokia 4A0-103 Exam
Explanation:
A fully loose LSP MtoR6" is enabled with FRR protection. All links have the same cost. After the
link between R2 and R4 goes down, FRR protection repairs the LSP and traffic traverses on R1-
R2-R7-R8-R4-R6. By default, which of the following about this LSP on an Alcatel-Lucent 7750 SR
is FALSE?
A.
The LSP will switch to R1-R3-R5-R6 after the resignal timer expires.
B.
The old primary path and its detours are torn down after the new primary path is established.
C.
CSPF must be enabled to find a more optimal path.
D.
"Pass Any Exam. Any Time." - www.actualtests.com 111
Nokia 4A0-103 Exam
The traffic is switched to R1-R3-R5-R6 in an MBB fashion.
Answer: A
Explanation:
Which of the following about an LSP protected with facility FRR is TRUE?
A.
The LSP can use protection tunnels used by other LSPs.
B.
The LSP can use facility and one-to-one FRR simultaneously.
C.
The LSP is limited to link protection.
D.
A detour protection tunnel is created for this LSP.
Answer: A
Explanation:
An LSP path is established on router R1 toward router R6. If the link between routers R4 and R6
goes down, which of the following is the quickest way for service recovery?
A.
Router R1 updates its FIB after a new SPF calculation.
B.
Router R1 switches to a secondary path.
C.
Router R4 switches to a FRR path.
D.
Router R4 switches to a standby secondary path.
Answer: C
Explanation:
LSP " to R8-5 " requests fast reroute protection. What could be done to remove the Failure Code
shown?
A.
The LSP must be enabled with CSPF on the head-end router.
B.
Fast reroute must be enabled on the downstream routers.
C.
A mixture of strict and loose hops must be defined in the primary path.
D.
CSPF and fast reroute must be enabled on all downstream routers.
Answer: A
Explanation:
Which of the following about Fast Reroute node protection tunnels is FALSE?
B.
Node protection tunnels can only be requested for a primary LSP path.
C.
Node protection tunnels are only used by one-to-one Fast Reroute.
D.
Link protection tunnels are established if a router is unable to establish node protection tunnels.
Answer: C
Explanation:
Which of the following about the use of RRO in fast reroute is FALSE?
A.
RRO is used to report the protection tunnel status to the head-end router.
B.
RRO contains the MP information that is required by a PLR for facility protection.
C.
RRO contains the label information that is expected by an MP for facility protection.
D.
RRO is used to inform downstream routers about the protection type requested.
Answer: D
Explanation:
An LSP traverses R1-R2-R3-R6 and one-to-one fast reroute is enabled. If the protected LSP
transports two labels, and router R2 has failed, how many labels will be on the detour path?
A.
1
B.
2
C.
3
D.
4
Answer: B
Explanation:
An LSP's primary path takes R1-R3-R5-R6. Its fully loose secondary path is configured for SRLG.
All links are of equal cost. Which path will the secondary path take?
A.
The secondary path will take R1-R3-R2-R4-R6.
B.
The secondary path will take R1-R2-R4-R6.
C.
The secondary path will take R1-R2-R3-R5-R6.
D.
The secondary path will take R1-R3-R2-R4-R5-R6.
Answer: A
Explanation:
Topic 4, Volume D
An LSP traverses the path R1-R2-R3. With one-to-one fast reroute enabled, which router
becomes a DMP for the detour tunnels?
A.
Router R1
B.
Router R2
C.
Router R3
D.
Router R4
E.
Router R5
Answer: E
Explanation:
A.
It provides the ability to establish connection oriented paths over a connectionless IP network.
B.
It provides a mechanism to engineer network traffic patterns independently of IP routing tables.
C.
D.
It can use GRE tunnels to transport data from many different protocols over an IP network.
Answer: D
Explanation:
A.
A separate label is used for each interface on which the FEC is advertised.
B.
A single label is assigned to a FEC for all interfaces on the same router,
C.
It is typically used when the device has ATM or Frame Relay interfaces.
D.
It uses more label resources than a per-interface label space.
Answer: B
Explanation:
A.
The penultimate router will forward packets to the eLER, based on the IP header.
B.
The eLER will receive packets with a top label value of 0.
C.
The eLER will receive packets with a top label value of 3.
D.
Answer: B
Explanation:
If an Alcatel-Lucent 7750 SR is an iLER operating in pipe mode, which of the following regarding
the TC field (EXP bits) is TRUE?
A.
The TC field is set based on the value of the DSCP field inside the customer packet.
B.
The TC field is set to a specific value via explicit administrative configuration.
C.
The TC field is set to a system generated random number.
D.
The TC field is set by the eLER.
Answer: B
Explanation:
Which MPLS label mode propagates a label mapping only for the FEC for which a router has a
label mapping for the FEC's next-hop?
A.
Independent control mode
B.
Ordered control mode
C.
Liberal label retention mode
D.
Conservative label retention mode
Answer: B
Explanation:
A.
An LSR answers requests for label mappings immediately, without waiting for a label mapping
from the next-hop.
B.
An LSR advertises label mappings to all peers for which it might be a next-hop for a given FEC.
C.
An LSR distributes a label mapping for a FEC when it has been requested to do so.
D.
An LSR propagates a label mapping downstream for a FEC. only if it has a label mapping for the
FEC's next-hop.
Answer: C
Explanation:
A.
Label values may be dynamically assigned by LDP.
B.
Label values may be dynamically assigned by RSVP-TE.
C.
Label values may be reserved for special uses.
D.
Answer: D
Explanation:
A.
They are multicast to the All Hosts address.
B.
They are broadcast to the subnet broadcast address.
C.
They are multicast to the All Routers address.
D.
They are broadcast or multicast, depending on the physical media.
Answer: C
Explanation:
A.
It allows link LDP to be configured on the edge devices only.
B.
It is used to signal the transport labels in the provider core.
C.
It allows selective control over which devices are configured for LDP.
D.
It is used to signal the service labels in the provider core.
Answer: D
"Pass Any Exam. Any Time." - www.actualtests.com 122
Nokia 4A0-103 Exam
Explanation:
A.
Frame mode requires multiple sessions between peers.
B.
The lower transport address initiates the session.
C.
Established LDP sessions run over a TCP connection.
D.
An LDP session is established immediately after Init messages are exchanged between peers.
Answer: C
Explanation:
After the Isp-ping command is executed, which of the following best describe the router's action?
A.
MPLS Echo Request packets are sent unlabeled to the prefix 192.10.1.2.
B.
MPLS Echo Request packets are sent within the LDP tunnel that are signaled for 192.10.1.2.
C.
"Pass Any Exam. Any Time." - www.actualtests.com 123
Nokia 4A0-103 Exam
MPLS Echo Request packets are sent within the RSVP-TE tunnel that are signaled for 192.10.1.2.
D.
MPLS Echo Request packets are sent over TCP.
Answer: B
Explanation:
When router R1 forwards a PATH message to router R2, which of the following about the PATH
message's IP header is TRUE?
A.
The options field is set to router alert.
B.
The source address is R1's egress interface address.
C.
The destination address is R2's ingress interface address.
D.
The HOP object includes R2's system address.
Answer: A
This LSP terminates on a system IP address. What is the system address of the destination node?
A.
10.32.1.2
B.
10.1.4.78
C.
10.48.1.1
D.
10.1.2.2
What are the default settings for RSVP-TE on the Alcatel-Lucent 7750 SR?
A.
Per-interface label space, liberal retention mode
B.
Per-platform label space; liberal retention mode
C.
Per-interface label space, conservative retention mode
D.
Per-platform label space, conservative retention mode
Answer: D
Explanation:
A.
The Isp-ping tool is used to perform a unidirectional LSP test.
B.
The router 10.10.10.2 is the egress router of the LSP.
"Pass Any Exam. Any Time." - www.actualtests.com 126
Nokia 4A0-103 Exam
C.
The router can reach the far-end of the LSP through an RSVP-TE tunnel.
D.
The router can reach the far-end of the LSP through an LDP tunnel.
Answer: D
Explanation:
A.
The inner label is the IPv4 Explicit Null. The outer label is the MPLS transport label,
B.
The inner label is an MPLS transport label. The outer label is the IPv4 Explicit Null.
C.
The inner label is the IPv6 Explicit Null. The outer label is an MPLS transport label.
D.
The inner label is an MPLS transport label. The outer label is the IPv6 Explicit Null.
Answer: C
Explanation:
A.
ERO is used by downstream routers to determine the next-hop for the LSP.
B.
ERO contains label information used to signal an LSP path.
C.
ERO is not always present in the PATH message.
Answer: B
Explanation:
A.
Type 10 opaque LSAs are supported by IS-IS.
B.
Type 10 opaque LSAs are flooded to all areas of the routing domain.
C.
Type 10 opaque LSAs are stored in an LSDB.
D.
Type 10 opaque LSAs are used for traffic engineering support.
Answer: D
Explanation:
Which of the following about MPLS shortcuts for IGP on an Alcatel-Lucent 7750 SR is FALSE?
A.
An IGP route takes priority over a transport tunnel.
B.
Both LDP and RSVP-TE based tunnels can be used.
C.
MPLS tunnels can be used to resolve the prefixes learned via IGP.
D.
Multiple MPLS tunnels can be installed in the FIB.
Initially, all ports on an Alcatel-Lucent 7750 SR have 10Gbps bandwidth. RSVP configuration limits
reservable bandwidth to 30 percent on all interfaces. An LSP is signaled reserving 1 Gbps
bandwidth. How much unreserved bandwidth is left on the interface?
A.
10 Gbps
B.
7 Gbps
C.
3 Gbps
D.
2 Gbps
Answer: D
Explanation:
How does a DMP inform the downstream routers that it has merged detour tunnels?
A.
The DMP sends the DMP_Object in each detour's PATH messages.
B.
The DMP summarizes PATH messages, giving each detour its own MSGJD.
C.
The DMP identifies itself as the previous hop in each detour's PATH message.
D.
The DMP sends a single PATH message containing the merged DETOUR_Objects.
Answer: D
"Pass Any Exam. Any Time." - www.actualtests.com 129
Nokia 4A0-103 Exam
Explanation:
Two LSPs traverse the path R1-R2-R3. Both LSPs are configured with facility fast reroute and link
protection. When router R1 is the PLR, which router becomes the Merge Point (MP) for this LSP?
A.
Router R1
B.
Router R2
C.
Router R3
D.
Router R4
E.
Router R5
Answer: B
Explanation:
The path of a fast reroute protected LSP is R1-R2-R3. Which of the following about the protected
LSP path is TRUE?
A.
All routers along the path, R1, R2, and R3 can be PLRs.
B.
If the R1-R2 link fails, router R4 becomes an MP.
C.
If the R2-R3 link fails, router R3 becomes a PLR.
D.
Router R1 is the LSP head-end and can be a PLR.
Answer: D
Explanation:
A.
The Standby with the highest next-hop IP.
B.
The first Standby in the list.
C.
The Standby with the longest uptime.
D.
The Standby with the lowest next-hop IP.
Answer: C
Explanation:
Which of the following about Fast Reroute link protection tunnels is FALSE?
A.
Link protection tunnels are established if a router is unable to establish node protection tunnels.
B.
Link protection tunnels are only requested for a primary LSP path.
C.
Link protection tunnels can be created for both one-to-one or facility Fast Reroute.
D.
Link protection tunnels detour around a failed next downstream router.
Answer: D
Explanation:
An LSP is configured with one-to-one FRR and node protection on a Alcatel-Lucent 7750 SR.
Which of the following is FALSE?
B.
A single protection tunnel can protect all LSPs that go through the same hop.
C.
A link protection tunnel is signaled if a node protection tunnel cannot be established.
D.
Protection tunnels used in this LSP are also detour tunnels.
Answer: B
Explanation:
A fully loose LSP "toR6" is configured. All links have the same cost and all routers are Alcatel-
A.
The LSP will switchover to another path if a failure occurs.
B.
The LSP will switchover to a better path as soon as it is available.
C.
CSPF must be enabled for this LSP to attempt to find a better path.
D.
The LSP will switchover to a better path in a MBB fashion.
Answer: B
Explanation:
An LDP tunnel is established on router R1 towards router R6. The link between routers R2 and R4
goes down. What will happen to the MPLS data traffic to router R6 IMMEDIATELY after the link
goes down?
A.
MPLS data traffic will be discarded until the IGP finds a new next-hop to router R3.
C.
MPLS data traffic will not be discarded because router R1 received labels from both next-hops,
routers R2 and R3.
D.
MPLS data traffic will not be discarded because of fast reroute capability on router R2.
Answer: B
Explanation:
Fill in the blanks: A ________device has all interfaces inside the provider domain, and a _______
device has at least one interface outside the provider domain.
A.
PE, P
B.
P, PE
C.
PE, CE
D.
CE, PE
E.
CE, P
Answer: B
Explanation:
Consider a device that uses per-platform label space; which of the following fields is NOT
contained in the LFIB?
B.
Outgoing label
C.
Incoming interface
D.
Outgoing interface
Answer: C
Explanation:
Which of the following regarding MPLS encapsulation for VPRN services is TRUE?
A.
The customer's Layer 3 header is removed at the iLER.
B.
The customer's Layer 2 header is removed at the iLER.
C.
The customer's Layer 3 header is removed at the eLER.
D.
The customer's Layer 2 header is removed at the eLER.
Answer: A
Explanation:
Which of the following about the Link LDP discovery process on the Alcatel-Lucent 7750 SR is
FALSE?
A.
LDP Hello messages are sent over TCP.
C.
LDP Hello messages are exchanged between all directly connected LDP enabled routers.
D.
Each LDP enabled router must have its own unique system IP address.
Answer: A
Explanation:
Which of the following devices assumes the active role during the establishment of an LDP
session?
A.
The peer with the higher physical address.
B.
The peer with the higher transport address.
C.
The peer with the lower physical address.
D.
The peer with the lower transport address.
E.
The peer that generated the first Hello message.
Answer: B
Explanation:
A.
Hello message
C.
Keepalive message
D.
Label Mapping message
E.
ACK message
Answer: E
Explanation:
A.
The router can reach prefix 192.10.1.2/32 through a RSVP-TE tunnel.
B.
The router can reach prefix 192.10.1.2/32 through an LDP tunnel.
C.
The router 10.10.10.2 is the egress router of the prefix 192.10.1.2/32.
D.
The Isp-ping tool is used to perform a unidirectional LSP test.
Answer: A
Explanation:
Which of the following about LSP path configuration on an Alcatel-Lucent 7750 SR is TRUE?
A.
The path must include at least one hop.
B.
The path may be used for multiple LSPs.
C.
The path may be used multiple times in a single LSP.
D.
The path must define a tunnel destination IP address.
Answer: B
Explanation:
RSVP session state for LSP 1 has timed out on router R3. Which of the following actions will
router R3 initiate to clear the RSVP session?
B.
Send a PATH Tear message toward router R1.
C.
Send a PATH Error message toward router R6.
D.
Send a PATH Error message toward router R1.
Answer: D
Explanation:
A.
The tail-end router performs the CSPF calculation for an LSP.
B.
CSPF calculations are always performed on RSVP-TE based LSPs.
C.
The head-end router performs the CSPF calculation for an LSP.
D.
Each downstream router performs its own CSPF calculation for an LSP.
Answer: C
Explanation:
A.
P routers run IPv4 only. PE routers run IPv4 only and exchange IPv6 routes using MP-BGP.
C.
P routers run IPv6 only. PE routers run both IPv4 and IPv6 and exchange IPv4 routes using MP-
BGP.
D.
P routers run IPv6 only. PE routers run IPv6 only and exchange IPv4 routes using MP-BGP.
Answer: B
Explanation:
To enable the LDP-over-RSVP feature, which of the following configurations is NOT required on
an Alcatel-Lucent 7750 SR?
A.
Enable the Idp-over-rsvp feature on all PEs and ABRs along the LSP tunnel.
B.
Configure Link-LDP sessions between each PE-ABR and ABR-ABR pair.
C.
Configure RSVP-TE LSPs in each area between each PE-ABR and ABR-ABR pair.
D.
Configure T-LDP sessions with the tunneling option.
Answer: B
Explanation:
Which of the following is NOT required when configuring an LSP with an admin group constraint
on an Alcatel-Lucent 7750 SR?
A.
Enable traffic engineering on all routers along the LSP path.
"Pass Any Exam. Any Time." - www.actualtests.com 141
Nokia 4A0-103 Exam
B.
Enable CSPF on the head-end router.
C.
Configure a path definition on all routers along the LSP path.
D.
Enable MPLS and RSVP on all routers along the LSP path.
Answer: C
Explanation:
An LSP path is established on router R1 toward router R6. If there is a problem on router R4, but
the link between R2 and R4 remains up, which of the following will affect the failure detection
time?
A.
The time router R2 takes to receive a PATH Error message from router R4.
B.
The time router R2 takes to find out a number of RSVP Hello messages have been missed.
D.
The time router R2 takes to receive a PATH message from router R4 after a PATH refresh
interval.
Answer: B
Explanation:
If the primary path goes down, which secondary LSP path will the head-end router select first?
A.
Secondary_Path-1
B.
Secondary_Path-2
C.
Secondary_Path-3
Answer: C
Explanation:
Facility fast reroute with node protection is enabled for an LSP, which of the following is FALSE?
A.
Each PLR signals a bypass tunnel that avoids the next-hop downstream router.
B.
When a failure occurs, the PLR pushs an additional label onto the label stack.
C.
No bypass tunnel is established if the PLR cannot provide node protection.
D.
The head-end router sets the local protection desired flag in the session attribute object.
Answer: C
Explanation:
An LDP tunnel is established on R1-R2-R4-R6 because the link between routers R3 and R6 is
down. With the LDP-IGP Sync feature enabled, what happens immediately after the link is
restored?
A.
A new LDP session is established on R1-R3-R6 as soon as the FIB is updated.
B.
The LDP session remains unchanged until the existing path R1-R2-R4-R6 goes down.
C.
A new LDP session is established on R1-R3-R6 as soon as router R1 receives a new label for
router R6.
D.
The LDP session remains unchanged until router R3 stops advertising the maximum metric for the
link to router R6.
Answer: D
Explanation:
An LSP traverses R1-R2-R4-R6 and one-to-one fast reroute with link protection is enabled. All
links have the same cost. Which of the following about DMP and MP is TRUE?
A.
R3 and R5 become DMPs; R6 becomes MP.
B.
R3 and R5 become DMPs; R4 becomes MP.
C.
R3, R5, and R6 become DMPs; R4 becomes MP.
D.
R1, R3, and R5 becomes DMPs; R4 and R6 become MPs.
Answer: A
Explanation:
Which of the following devices inspects the MPLS header in the received packet, and exchanges it
for a new MPLS header?
A.
B.
LER
C.
LSR
D.
PE
E.
eLER
Answer: C
Explanation:
A.
A group of packets that will be forwarded by the router in the same manner, over the same path.
B.
A group of packets that arrive at the router on the same interface,
C.
A group of packets that leave the router on the same interface.
D.
A group of packets that arrive at the router on the same interface, from the same source.
Answer: A
Explanation:
Which MPLS mode saves only active label mappings received from peer LSRs?
A.
B.
Liberal label retention
C.
Downstream on demand
D.
Downstream unsolicited
Answer: A
Explanation:
Which of the following about label modes on the Alcatel-Lucent 7750 SR is FALSE?
A.
RSVP uses downstream on demand label distribution mode.
B.
LDP uses conservative label retention mode.
C.
LDP advertises label mappings to all peers for which it might be a next-hop for a given FEC.
D.
RSVP distributes a label mapping for a FEC when it has been requested to do so.
Answer: B
Explanation:
This policy is applied on a router as an LDP export policy and an LDP session has been
established between this router and its neighboring router. In addition to the FECs learned from its
neighbors, what additional FECs will appear in this router's LIB?
A.
All FECs that are in the 192.168.1.0/24 address space.
B.
Local FECs that are in the 192.168.1.0/24 address space.
C.
All FECs that are not in the 192.168.1.0/24 address space.
D.
All FECs except the local FECs that are in the 192.168.1.0/24 address space.
Answer: B
Explanation:
A.
It supports traffic protection using IGP equal cost paths.
B.
It supports CAC to prevent resource overbooking.
C.
"Pass Any Exam. Any Time." - www.actualtests.com 149
Nokia 4A0-103 Exam
It supports LSPs with traffic engineering constraints.
D.
It supports LSPs that follow the IGP best path.
Answer: A
Explanation:
LSP 1's link between routers R3 and R6 has failed, and the RESV state at router R3 has timed
out. Which of the following actions will router R3 initiate?
A.
Send a PathTear message towards router R6.
B.
Send a PathTear message towards router R1.
C.
Send a ResvTear message toward router R6.
D.
Send a ResvTear message toward router R1.
Answer: D
Click on the exhibit. After the Isp-ping command is executed, which of the following best describe
the router's action?
A.
MPLS Echo Request packets are sent within the RSVP-TE tunnel that is signaled for "lsp-toR2".
B.
MPLS Echo Request packets are sent within the LDP tunnel that is signaled for Mlsp-toR2".
C.
MPLS Echo Request packets are IP-routed to the destination address of "lsp-toR2".
D.
MPLS Echo Request packets are sent to the destination address of "lsp-toR2" over TCP.
Answer: A
Explanation:
Which of the following about IS-IS Traffic Engineering on an Alcatel-Lucent 7750 SR is FALSE?
A.
Traffic engineering information is carried in the extended TLVs.
B.
Traffic engineering must be enabled on all IP/MPLS routers along the LSP path.
C.
Traffic engineering information is stored in the opaque database,
D.
Traffic engineering is required for constraint-based LSPs.
Answer: C
Explanation:
A.
Type 8 LSA — Link Local LSA
B.
Type 9 LSA — Link local Opaque LSA
C.
Type 10 LSA — Area local Opaque LSA
D.
Type 11 LSA —AS Opaque LSA
Answer: C
Explanation:
A.
Selected labels from the FIB are populated to the LFIB.
B.
Selected labels from the RIB are populated to the FIB.
C.
Selected labels from the LIB are populated to the FIB.
D.
Selected labels from the LIB are populated to the LFIB.
Answer: D
Explanation:
A.
Enabling VPNs
B.
Enabling traffic engineering
C.
Enabling network security
D.
Enhancing network resiliency
Answer: C
Explanation:
Which of the following fields does NOT appear in the MPLS label header?
A.
Label
B.
Frame check sequence
C.
Traffic Class (previously called Experimental)
D.
Time To live
E.
Bottom of stack bit
Answer: B
Explanation:
What is the possible reason that the label for prefix 192.10.1.2/32 is not active?
A.
The router does not have a route to reach to the peer 10.10.10.2/32.
B.
The router does not have a route to reach to the prefix 192.10.1.2/32.
C.
The router does not have an export policy defined to export the prefix 192.10.1.2/32 into LDP.
D.
The router receives an invalid label for the prefix 192.10.1.2/32 from its peer.
Answer: B
Explanation:
A.
"Pass Any Exam. Any Time." - www.actualtests.com 154
Nokia 4A0-103 Exam
They list the RSVP session names that the router is refreshing,
B.
They list the Message IDs that the router is refreshing,
C.
They list the Tunnel IDs that the router is refreshing.
D.
They list the LSP I Ds that the router is refreshing.
Answer: B
Explanation:
If an LSP needs to use an admin group, which of the following configurations is NOT required on
the Alcatel-Lucent 7750 SR?
A.
Assign an admin group to a MPLS interface.
B.
Configure CSPF on the LSP.
C.
Configure at least one strict hop on the LSP path.
D.
Configure an "include" or "exclude" statement on the LSP path.
Answer: C
Explanation:
The partial command output from an Alcatel-Lucent 7750 SR is shown. Which of the following
about this LSP path is TRUE?
A.
R4 (10.10.10.4) has established a link protection tunnel.
B.
R6 (10.10.10.6) has established a link protection tunnel.
C.
R2 (10.10.10.2) has established a node protection tunnel.
D.
R1 (10.10.10.1) has not established a node protection tunnel.
Answer: A
Explanation:
A.
The MPLS label value may be carried in an ATM header.
B.
The MPLS label value may be carried in a shim header.
C.
The MPLS label value may be carried in an OSPF header.
D.
The MPLS label value may be carried in a Frame Relay header.
Answer: C
An IS-IS TE enabled router has an interface on a 500Mbps link and it is configured with a 25%
subscription. If this interface is not used by any LSPs. what value will be shown in the Reservable
Bandwidth sub-TLV?
A.
125 Mbps
B.
500 Mbps
C.
625 Mbps
D.
2000 Mbps
Answer: A
Explanation:
The LSP "toR6" is configured with a fully strict path on an Alcatel-Lucent 7750 SR. Which of the
following configurations is required to enable fast reroute for this LSP?
A.
Enable fast-reroute on all routers along the path. R1, R2, R4, and R6.
B.
Enable both link-protection and node-protection on router R1.
C.
Enable fast-reroute with either one-to-one or facility mode on this LSP.
D.
Enable link-protection only on router R4.
Answer: C
Explanation:
Which MPLS label mode saves label mappings received from all peer LSRs?
A.
Conservative label retention
C.
Downstream on demand
D.
Downstream unsolicited
Answer: B
Explanation:
An LDP-over-RSVP tunnel is established between PE-1 and PE-2. Which of the following is NOT
required to protect the LDP-over-RSVP tunnel?
A.
PE-1 requires T-LDP sessions to both ABR-1 and ABR-2.
B.
PE-1 requires a full mesh of RSVP-TE LSPs to all routers in area 1.
C.
ABR-1 requires T-LDP sessions to all ABRs in area 0.
D.
PE-1 requires fast reroute enabled on all RSVP-TE LSPs.
Answer: B
Explanation: