Beruflich Dokumente
Kultur Dokumente
ASSP
DUAL REVERSIBLE
MOTOR DRIVER
MB3863
■ DESCRIPTION
The MB3863 is an IC motor driver with two independent reverse control functions. It drives motor drives of front-
loading VTRs and auto-reverse cassette decks and stepping motors by reversible control at TTL and CMOS levels.
A heat protection circuit is incorporated to prevent damage by overheating.
■ FEATURES
• Wide voltage range: VCC = +4 to +36 V
• Motor drive current: 500 mA (1.2 A for surge current)
• Two internal independent drivers
• Internal heat protection circuit
• Control at TTL and CMOS level
• Stand-by mode
• Brake function to stop motors
• Internal surge absorption diode
• Stepping motor application
• Symmetrical pin layout
■ PACKAGE
(FPT-20P-M01)
MB3863
■ PIN ASSIGNMENT
(TOP VIEW)
B-IN 1 20 N.C.
B-V CC 2 19 A-V CC
ch.1 ch.1
N.C. 3 18 A-IN
B-OUT 4 17 A-OUT
GND 5 16 GND
GND 6 15 GND
B-OUT 7 14 A-OUT
N.C. 8 13 A-IN
ch.2 ch.2
B-V CC 9 12 A-V CC
B-IN 10 11 N.C.
(FPT-20P-M01)
N.C.: No connection
■ BLOCK DIAGRAM
A-V CC
A-IN
Drive A-OUT
Input logic ch.1
ch.1
channel 1 Drive B-OUT
B-IN
B-V CC
Heat protection
circuit
A-V CC
A-IN
Drive A-OUT
Input logic
ch.2 ch.2
channel 2
Drive B-OUT
B-IN
B-V CC
GND
2
MB3863
3
MB3863
■ ELECTRICAL CHARACTERISTICS
(VCC = 24 V, VIN = 2.4 V, Ta = +25 °C)
Values
Parameter Symbol Conditions Unit
Min. Typ. Max.
Stand-by Supply Voltage ICC0 VCC = +24 V, VIA = VIB = 0 V — — 100 µA
ICC1 IO = 0 mA — 24 38 mA
Supply Voltage ICC2 IO = 500 mA — 24 — mA
ICC3 IO = 0 mA, VIA = VIB = +2.4 V — 37 — mA
High level VOH IO = 500 mA 22.65 23 — V
Output Voltage
Low level VOL IO = 500 mA — 0.35 0.65 V
Saturated Output Voltage VSAT IO = 500 mA — 1.35 2.00 V
Input Current IIH VIN = +2.4 V — 250 400 µA
Surge Absorption Diode Voltage
VF IO = 1.2 A — 2.0 — V
in Forward Direction
4
MB3863
■ OPERATIONS
1. Forward and Reverse
Switching control mode A or B pairs Q2 and Q3, or Q1 and Q4, respectively, while reversing the supply current
to the motor for each switching. When Q2 and Q3 are in use, B-OUT and A-OUT are High level and Low level,
respectively. In this case, current flows B-OUT→ motor → A-OUT, causing forward operation as described in
the table below.
When Q1 and Q4 are in use, current flows in the reverse direction to the above flow, causing reverse motor
operation.
2. Brake
Control mode C operates Q2 and Q4 while stopping Q1 and Q3.
Since A-OUT and B-OUT are held at Low level, both poles of the motor are short-circuited and the motor is
stopped.
3. Stand-by
Control mode D turns Q1 to Q4 OFF and the motor has no current flow.
In this mode, the power supply current is less than 100 µA.
Input mode* Operation state of output transistor State of output pin
Mode Output operation mode
A=IN B=IN Q1 Q2 Q3 Q4 A-OUT B-OUT
A 1 0 OFF ON ON OFF L H Forward (Reverse)
B 0 1 ON OFF OFF ON H L Reverse (Forward)
C 1 1 OFF ON OFF ON L L Brake
D 0 0 OFF OFF OFF OFF — — Open (High impedance)
* : Input mode:1: +2.4 V Min.
0: +0.4 V Max.
5
MB3863
Q1 Q3
Control block
A-OUT B-OUT
Q2 Q4
GND
6
MB3863
■ TYPICAL CONNECTION
V CC
1 kΩ
A-IN A-V CC
B-OUT
B-V CC
MB3863
A-V CC
1 kΩ
A-IN A-OUT
B-V CC
ch.1 ch.2
GND GND
Note : If input voltage is applied when power is not supplied, over-current flows into the device via the input pins.
In this case, connect a resistor of at least 1 kΩ in series with the input pins to prevent passage of a large current.
7
MB3863
Supply Voltage vs. Supply Current Output Current vs. Output Voltage
80 2.0
Output voltage:
Supply current:
60 1.5
V OH, V OL(V)
V INA − V INB = 2.4 V(At braking)
40 1.0 ∆V OH(V CC − V OH)
I CC(mA)
20 0.5
V INA = + 2.4 V, V INB = + 0.4 V V OL
0 0
0 5 10 15 20 25 30 35 40 0 100 200 300 400 500
Supply voltage: V CC(V) Output current: I O(mA)
Input Voltage vs. Input Current Input Voltage vs. Input Current
700 10
V CC = +3.5 V V CC = +38 V
600 Input current 8
I IH(mA)
500 6
Input current:
400 4
I IH(µA)
300 2
200 0
0 5 10 15 20 25 30 35 40 45
100 Input voltage: V IN(V)
0
0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0
Input voltage: V IN(V)
80 V CC = +36 V
V CC = +24 V
Supply current:
60
I CC(mA)
V CC = +7 V
40
V CC = +4 V
20
0
0 0.2 0.4 0.6 0.8 1.0 1.2
Output current: I O (mA)
8
MB3863
SOP-20P
8
6
Allowable loss P D (W)
0 25 50 75 100
Ambient temperature Ta (˚C)
Conditions of heat sink: Without heat sink plate
9
MB3863
■ ORDERING INFORMATION
Part number Package Remarks
20-pin plastic SOP
MB3863PF
(FPT-20P-M01)
10
MB3863
■ PACKAGE DIMENSION
20-pin plastic SOP Note 1 : Pins width and pins thickness include plating thickness.
(FPT-20P-M01) Note 2 : *This dimension includes resin protrusion.
1 10 "A" 0.25(.010)
+0.10
0.50±0.20 0.10 –0.05
+.004
(.020±.008) .004 –.002
0.60±0.15 (Stand off)
(.024±.006)
0.10(.004)
11
MB3863
FUJITSU LIMITED
F0108
FUJITSU LIMITED Printed in Japan