Beruflich Dokumente
Kultur Dokumente
ASSEMBLY LIGHT
PANEL ACCESSORY
Figure 2
3. Remove the plastic plug button in the switch
hole by hitting the plastic stems off with a screw-
driver tip.
4. Connect the red wire of the light harness and
the red tail light wire to the center terminal of the
DESCRIPTION switch. The fused wire on the harness is connected
The Model 8-0812 light Panel Accessory fits the to the side terminal. (See Fig. 1 and Wiring Diagrams.)
short frame, vertical shaft, and Lawn Ranger Model 5. String wires through the switch hole and down
1-8745. through the rubber grommet. (See Fig. 2.)
FOR SHORT FRAME AND VERTICAL SHAFT TRAC-
TORS USE INSTRUCTIONS ON PAGE 1 AND 2.
LAWN RANGER INSTRUCTIONS BEGIN ON PAGE 2.
ASSEMBLY
1. IMPORTANT: Disconnect the battery ground
cable from the battery. This will prevent hot sparks
and shorts.
Figure 3
6. The green fused wire is connected to the bat-
tery positive terminal.
7. The hood escutcheon plate can be removed by
breaking off the stems with a screwdriver tip. Install
the two Ya rivets through the hood and reflector hous-
ing. The rivets are held in place with the push-on
nuts, the slotted end of the nut goes on the rivet first,
Figure 1 see Fig. 4 and the Exploded View DrawilJg.
10. String the red wire of the harness forward
under the left side of the engine and along the left
side of the hood. Connect the wire leads to the con-
nector as shown in Fig. 6. Fasten the wire to the
hood with the clips provided. Any excess wire can
be looped and taped to the inside of the hood.
11. Mount tail light base to the rear of the fender
as shown in Fig. 7.
12. String the red tail light wire down inside the
hoodstand (stay behind lift arm shaft) and back in-
side the tool box. Connect the black tail light wire
to the red lead from the switch with the connector as
shown in Fig. 8.
13. Mount fuel tank back in position. Connect
Figure 4
battery ground cable, and try lights. If lights fail to
come on - check wiring - see diagrams. The ground
for the lights is transmitted through the hood latch
rod; therefore, the lights may go out when the hood
is up.
Figure 5
8. Insert the socket wires, springs, and bulbs as
shown in Fig. 4.
9. Mount the lens to the opening and fasten with
the four machine screws as shown in Fig. 5.
Figure 8
INSTRUCTIONS
LAWN RANGER MODEL 1·8745
ASSEMBLY
1. IMPORTANT: Disconnect the battery ground
cable from the battery. This will prevent hot sparks
and shorts.
2. Drill holes in the rear of seat pan. (See Fig. 1.)
Drill three ~2 Dia. holes at the locations shown.
Figure 6
Figure 7 Figure 1
-2-
3. Mount the tail light to the seat pan with the Run the red wire forward and under the wire clip
# 10 screws, lockwashers, and nuts as shown in Fig. provided on the engine as shown. Connect this wire
2. The 6" black ground wire fits under the nut of to the connector, and fasten it to the side of the grill
screw marked "A" to under the nut of screw marked with the wire clips. (See Fig 4.)
"8". (See Fig. 2.)
Figure 4
Figure 2
Slip the two remaining ends of the wire harness
through the hole at the base of the battery into the
4. Insert the wires, springs, and bulbs in the re- dash area.
flector housing. Using the four #6-32 screws mount the 6. Use a screwdriver to pry off the plug button
lens and the reflector housing to the grill as shown in covering the switch opening. (See Fig. 5.)
Fig. 3. Slip one end of the 13)1" black ground wire
Pull the wire leads of the harness through the
under the lip of the housing and connect the other
opening.
end to one of the grill hinge bolts as shown. Attach
the double connector to the black lead wires from the
housing.
Figure 5
-3-
LIGHTS
o
w
""
GREEN
ow
"" LIGHT SWITCH
Wiring Diagram
I,
Lawn Ranger Lawn Tractor
-4-
GREEN
Item
No. No. Description Req'd.
#6-32 4
7 100074 Terminal Spade
7184
9 H"adlight Ground
10
Connector 3-Way 1
923003 2
7429 2
16 8042
17 2
19 2
2
920079-4
22
23
24
U. S. A. NO. A-SI92