Beruflich Dokumente
Kultur Dokumente
Mi1002 6.06
Submersible Pumps
4400
Features:
■ 4 performance ranges - 35, 45, 60 & 90 GPM.
■ Stainless steel discharge head and motor bracket.
■ High flow impellers and stages are glass-filled Noryl®* for maximum
efficiency.
■ Ceramic shaft sleeve and rubber discharge bearing eliminates sand wear.
■ Intermediate bearing for increased shaft stability.
■ Floating eye and hub seals for improved performance and efficiency.
■ Stainless steel hex pump shaft, shell and shaft coupling.
■ High capacity upthrust assembly for protection during start-up and operation
(45, 60 and 90 GPM models).
■ Powered by Franklin’s corrosion-resistant 4” submersible motors.
■ 2” NPT Discharge.
■ Check valve must be ordered separately.
4” High Capacity
35-90 GPM Stainless Steel
Ordering Information
1 - 10 HP 4" Pump Ends
Ordering Info. Dimensions
GPM HP Stages Wt.
Old Model No. New Model No. Order No. Shell PEA
1 6 F4P35X6 35FA1S4-PE 93613506 11.10 15.00 9
1.5 8 F4P35X8 35FA15S4-PE 93613508 13.60 17.50 10
35 2 10 F4P35X10 35FA2S4-PE 93613510 16.10 20.00 11
3 14 F4P35X14 35FA3S4-PE 93613514 21.10 25.00 13
5 22 F4P35X22 35FA5S4-PE 93613522 31.10 35.00 17
FEET
PSI
700 60
300
EFFICIENCY%
200
5 HP 55
600 50
175 250
45
150 500
200
125 3 HP
400
150
100
300 2 HP
75
1.5 HP
100
200
1 HP
50
50
100
25
0 0 0
0 10 20 30 40 50 GPM
0 2 4 6 8 10 12 M3PH
Notes: 1. Performance shown does not include friction loss in the drop pipe.
2. All performance data is based on rated motor nameplate voltage.
4400
Submersible Pumps
4” High Capacity
35 GPM Performance Chart
Shut-off 171 ft
30 36 31 25
40 30 24 15
1 50 23 14
60 12
70
80
Shut-off PSI 65 57 48 39 31 22 13 5
0 - 49 46 43 40 36 32 27 22 16 8
20 45 42 39 35 31 26 20 14
Shut-off 226 ft
30 41 38 34 30 25 20 13
40 37 33 29 24 18 11
1.5 50 33 29 24 18 10
60 28 23 17 9
70 22 16 7
80 14 3
Shut-off PSI 89 81 72 63 54 46 37 28 20 11 2
0 - 50 48 45 43 40 37 34 31 28 24 19 14 7
20 47 45 42 39 36 33 30 27 22 18 13 3
Shut-off 288 ft
30 44 41 39 36 33 30 26 22 17 12
40 41 38 35 32 29 25 21 16 10
2 50 38 35 32 29 25 20 16 9
60 35 31 28 24 20 15 8
70 31 27 23 19 14 6
80 27 23 18 13 4
Shut-off PSI 116 107 99 90 81 73 64 55 47 38 29 21 12 3
0 - - 50 48 47 46 44 42 39 37 35 33 31 28 26 23 19 15 10
20 49 48 47 45 43 41 39 37 35 33 30 28 25 22 18 14 8
Shut-off 496 ft
30 48 46 45 43 41 39 37 35 32 30 27 25 21 17 13 7
40 46 44 42 40 38 36 34 32 29 27 24 20 17 12 5
3 50 44 42 40 38 36 34 31 29 26 24 20 16 12 4
60 42 40 38 36 33 31 29 26 23 19 15 11 2
70 39 37 35 33 31 28 26 22 19 15 10
80 37 35 33 30 28 25 22 18 14 9
Shut-off PSI 165 156 148 139 130 122 113 104 96 87 78 70 61 52 44 35 26 18 9
0 - - - - 50 49 48 47 46 45 44 43 42 40 39 38 37 36 34 33 30 25 20 12
20 - - 49 48 48 47 46 45 44 42 41 40 39 38 36 35 34 33 32 30 26 20 13
Shut-off 638 ft
30 - 49 48 47 46 45 44 43 42 41 40 39 38 36 35 34 33 31 30 28 23 17 8
40 49 48 47 46 45 44 43 42 41 40 39 37 36 35 34 32 31 30 28 26 21 13
5 50 48 47 46 45 44 43 42 41 40 38 37 36 35 33 32 31 30 28 26 24 18 9
60 47 46 45 44 43 42 41 39 38 37 36 34 33 32 31 29 28 26 24 21 14
70 46 45 44 43 42 40 39 38 37 35 34 33 32 31 29 27 25 23 21 18 10
80 45 44 42 41 40 39 38 36 35 34 33 32 30 29 27 25 23 20 18 15 3
Shut-off PSI 268 259 251 242 233 225 216 207 199 190 181 173 164 155 147 138 129 121 12 103 82 60 38 17
FEET
PSI
EFFICIENCY%
450
350 1000
60
400
300 900 50
40
250 350 800 7.5 HP
225
300 700
200
600
175 250 5 HP
150 500
200
125 400
150 3 HP
100
300
2 HP
75 100
200 1.5 HP
50
50
100
25
0 0 0
0 10 20 30 40 50 60 70 80 GPM
0 2 4 6 8 10 12 14 16 18 M3PH
Notes: 1. Performance shown does not include friction loss in the drop pipe.
2. All performance data is based on rated motor nameplate voltage.
3. Performance for former XP models are the same as 45 gpm models.
4400
Submersible Pumps
4” High Capacity
45 GPM Performance Chart
Shut-off 190 ft
10 62 56 51 45 38 29 19
20 55 50 44 36 28 17 5
1.5 30 49 42 35 26 16 3
40 41 34 25 14
50 33 23 12
60 22 10
Shut-off PSI 74 65 56 48 39 30 22 13 4
0 71 65 60 56 52 48 44 40 35 29
Shut-off 250 ft
10 64 59 55 51 48 44 40 34 28 20
20 58 54 51 47 43 39 33 27 19 9
2 30 54 50 47 43 38 32 26 17 7
40 50 46 42 37 32 24 16 5
50 45 41 36 31 23 14 3
60 41 36 29 22 13 1.5
Shut-off PSI 104 95 87 78 69 61 52 43 35 26 9
0 72 68 65 62 59 56 53 50 47 43 36 31 26 20
10 68 64 61 58 55 52 49 46 43 39 30 25 19 12
20 64 61 58 55 52 49 46 42 38 34 24
Shut-off 350 ft
30 60 57 54 52 48 45 42 38 34 29 17
40 57 54 51 48 45 41 37 33 28 22 16
3 50 54 51 47 44 41 37 32 27 21 15
60 50 47 44 40 36 31 26 20 14
70 46 43 39 35 31 25 19 13
80 43 39 35 30 24 18 12
90 38 34 29 24 18 11
100 33 28 23 16 9
Shut-off PSI 143 134 126 117 108 100 91 82 74 65 48 39 30 22 13 4
0 - - 69 66 63 61 59 57 55 53 50 48 46 44 42 40 38 36 33
20 68 65 63 60 57 56 54 52 51 49 46 44 42 40 38 35 32 29 26
40 62 60 57 56 54 52 50 48 48 47 45 39 37 34 32 28 25 21
Shut-off 575 ft
60 57 55 51 51 50 48 46 44 43 41 36 33 31 27 24 20 16
80 53 51 49 47 46 44 42 40 38 35 30 26 23 19
5 100 49 47 45 43 41 39 37 34 32 29 25 18
120 45 43 41 39 36 34 31 28 24 20 16
140 40 38 35 33 30 27 23 19
160 35 32 29 26 22 18
170 31 28 25 21 17
Shut-off PSI 236 227 219 210 201 193 184 175 167 158 141 132 123 115 106 97 89 80 71
Depth to Pumping Water Level, or Lift, in Feet
HP PSI Shaded Areas Indicate Most Efficient Performance
50 100 150 200 250 300 350 400 450 500 550 600 650 700 750 800 850 900 950
0 - - - 57 54 50 47 44 40 36 32 28 24 18 11 3
20 - - 57 54 50 47 44 40 36 32 28 24 18 11 3
40 - 58 54 51 48 45 41 37 33 29 24 18 12 5
60 58 55 52 48 45 41 37 33 29 25 19 12 5
Shut-off 815 ft
80 55 52 48 45 41 37 33 29 25 19 12 5
100 52 48 45 42 38 34 30 25 20 14 6
7.5 120 49 45 42 38 34 30 25 21 14 7
140 45 42 38 35 30 26 21 15 7
160 42 39 35 31 26 21 15 8
180 39 35 31 27 22 16 8
200 35 31 27 22 16 9
220 32 27 22 17 10
Shut-off PSI 331 310 288 266 245 223 201 180 158 136 115 93 71 50 28 6
FEET
PSI
450
300 1000
400
275 900
EFFICIENCY%
225
300 700
200 60
600 50
175 250
7.5 HP 40
150 500
200
5 HP
125 400
150
100
300
3 HP
75 100
200 2 HP
50
50
100
25
0 0 0
0 10 20 30 40 50 60 70 80 GPM
0 2 4 6 8 10 12 14 16 18 M3PH
Notes: 1. Performance shown does not include friction loss in the drop pipe.
2. All performance data is based on rated motor nameplate voltage.
3. Performance for former YP models are the same as 60 gpm models.
4400
Submersible Pumps
4” High Capacity
60 GPM Performance Chart
Shut-off 195 ft
10 80 77 74 71 68 65 61 57 52 47 42 36
20 74 70 67 64 60 56 51 46 40 34 26 18
2 30 66 63 59 54 49 44 38 31 24 16
40 57 53 48 42 36 29 21 13
50 46 40 34 27 19
60 32 24 16
Shut-off PSI 74 69 65 61 56 52 48 43 39 30 26 22 17 13 9 4
0 90 87 85 83 81 79 76 74 72 70 67 65 62 59 56 53 49
Shut-off 265 ft
10 84 82 80 78 76 74 71 69 67 64 61 58 55 51 47 43 38
20 79 77 75 73 71 68 66 63 60 57 54 50 46 42 37 32 26
3 30 74 72 70 68 65 59 56 53 49 45 40 35 30 24
40 69 67 64 62 58 55 52 48 43 39 34 28 22
50 63 61 58 54 50 46 42 37 32 26
60 56 63 49 45 41 36 30 24
Shut-off PSI 108 104 100 95 91 87 82 78 74 69 65 61 56 52 48 43 39
HP PSI 20 40 60 80 100 120 140 160 180 200 220 240 260 280 300 320 340
0 85 85 80 80 75 75 70 70 65 65 60 55 50 45 45 35 30
10 85 80 80 75 75 70 70 65 60 60 55 50 45 40 35 30 25
20 80 80 75 75 70 70 65 60 60 55 50 45 40 35 30 25 15
Shut-off 425 ft
30 80 75 75 70 65 65 60 60 55 50 45 40 35 30 20 15 5
40 75 70 70 65 65 60 55 55 50 45 40 35 30 25 10 5
5 50 70 70 65 65 60 55 55 50 45 40 35 25 25 10 5
60 70 65 65 60 55 50 50 45 40 30 25 20 10 5
70 65 60 60 55 50 45 40 35 30 25 15 10
80 60 60 55 50 45 40 35 30 25 15 10
90 60 55 50 45 40 35 30 20 15 5
100 55 50 45 40 35 30 20 15 5
Shut-off PSI 173 165 156 147 139 130 121 113 104 95 87 78 69 61 52 43 35
HP PSI 50 100 150 200 250 300 350 400 450 500 550 600 650 700 750 800 850
0 - 78 73 68 63 56 49 40 28 15 2
20 78 73 68 63 56 49 40 28 15 2
Shut-off 555 ft
40 75 69 64 58 50 41 30 18 3
60 70 64 58 50 42 31 18 4
7.5 80 65 59 51 43 32 19 5
100 59 52 43 32 20 6
120 52 44 33 21 8
140 44 34 21 8
160 35 22 9
Shut-off PSI 221 199 177 156 134 113 91 69 48 26 4
0 - - 75 72 69 65 61 56 51 45 38 30 21 13 4
20 - 75 72 69 65 61 56 51 46 38 31 22 14 5
Shut-off 772 ft
40 75 72 69 65 61 56 51 45 39 31 22 14 5
60 73 69 66 62 57 52 47 40 32 24 15 6
10 80 70 66 62 57 52 47 40 32 24 15 6
100 66 62 58 53 48 41 34 25 16 7
120 63 58 53 48 41 34 25 16 8
140 58 53 48 42 34 26 17 8
160 54 49 43 35 27 18 9
Shut-off PSI 312 290 269 247 225 204 182 161 139 117 96 74 52 31 9
FEET
PSI
450
EFFICIENCY%
7.5 HP
125
175 400 60
50
150 350 40
100
300
125 5 HP
75 250
100
200
75 3 HP
50
150
2 HP
50
100
25
25
50
0 0 0
0 10 20 30 40 50 60 70 80 90 100 110 120 130 GPM
0 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 M3PH
Notes: 1. Performance shown does not include friction loss in the drop pipe.
2. All performance data is based on rated motor nameplate voltage.
4400
Submersible Pumps
4” High Capacity
90 GPM Performance Chart
Shut-off 120 ft
10 105 100 90 80 70 55 40 20
2 20 85 75 65 50 35 15
30 60 45 30 10
40 25 5
Shut-off PSI 43 39 35 30 26 22 17 13 9 4
0 140 130 120 115 105 100 95 90 80 75 65 55 45 30 15
10 120 110 105 100 95 85 80 70 65 55 40 25 10
Shut-off 167 ft
20 105 95 90 85 80 70 60 50 35 20 54
3 30 90 80 75 65 55 45 35 15
40 75 65 55 40 30 10
50 50 40 25 5
60 20
Shut-off PSI 64 59 55 51 46 42 38 33 29 25 20 16 12 7 3
HP PSI 20 40 60 80 100 120 140 160 180 200 220 240 260 280 300 320 340
0 145 135 125 120 110 105 95 85 80 70 55 45 30 10
10 135 125 115 110 100 95 85 75 65 55 40 25 10
20 125 115 110 100 95 85 75 65 55 40 25 5
30 115 105 100 90 85 75 65 50 40 20 5
Shut-off 285 ft
40 105 100 90 80 70 60 50 35 20
5 50 95 90 80 70 60 45 35 15
60 90 80 70 60 45 30 15
70 80 70 55 45 30 10
80 65 55 40 25 5
90 50 40 25 5
100 35 20
Shut-off PSI 115 106 97 89 80 71 63 54 45 37 28 19 11 2
HP PSI 20 50 80 110 140 170 200 230 260 290 320 350 380 410 440 470 500
0 140 135 125 115 110 100 95 85 75 65 55 45 30 15
20 130 120 110 105 95 90 80 70 60 50 35 20 5
30 120 115 105 100 90 85 75 65 55 40 25 10
40 115 110 100 95 85 75 65 55 45 30 10 Shut-off 425 ft
50 110 105 95 85 80 70 60 45 30 15
7.5 60 105 95 90 80 70 60 50 35 20 5
80 95 85 75 65 55 40 25 10
100 80 70 60 50 35 20
120 65 55 40 25 10
140 45 35 20
160 25 10
Shut-off PSI 175 162 149 136 123 110 97 84 71 58 45 32 19 6
4400
Features:
■ Heavy-duty stainless steel discharge head and motor bracket.
■ Stainless steel shaft, shell, intake screen and cable shield for corrosion
resistance and longer life.
■ Stainless steel wear ring and Urethane floating eye seal for improved
performance and efficiency.
■ Glass-filled Noryl®* impeller stage assemblies provide incredible strength
and durability.
■ Ceramic shaft sleeve and rubber discharge bearing minimizes bearing wear
and shaft misalignment without affecting pump efficiency.
■ 3” NPT tapping in heavy-duty stainless steel discharge head.
■ Fastener kit supplied for both 4” and 6” motors enabling 5-10 hp units to be
mounted to either a 4" or 6" submersible motor.
■ One year unconditional warranty against failure from sand locking in
abrasive well conditions.
* Noryl® is a Registered Trademark of G.E.
6” High Capacity
50-125 GPM
Ordering Information
6" Pump Ends
Motor Ordering Info. Dimensions
GPM HP Stages Wt.
Fit Model No. Order No. Pump End Only
1.5 3 4" 50FA15S6-PE 94825003 13.51 30
2 4 4" 50FA2S6-PE 94825004 15.13 31
3 5 4" 50FA3S6-PE 94825005 16.76 32
50 5 8 4" & 6" 50FA5S6-PE 94825008 21.63 36
7.5 11 4" & 6" 50FA7S6-PE 94825011 26.51 40
10 15 4" & 6" 50FA10S6-PE 94825015 32.94 46
3 3 4" 75FA3S6-PE 94827503 13.51 30
5 5 4" & 6" 75FA5S6-PE 94827505 16.76 32
7.5 7 4" & 6" 75FA7S6-PE 94827507 20.01 35
75 10 9 4" & 6" 75FA10S6-PE 94827509 23.26 38
15 13 6" 75FA15S6-PE 94827513 29.76 43
20 17 6" 75FA20S6-PE 94827517 36.19 48
25 23 6" 75FA25S6-PE 94827523 46.00 54
5 3 4" & 6" 100FA5S6-PE 94820003 14.62 32
7.5 5 4" & 6" 100FA7S6-PE 94820005 18.51 32
10 6 4" & 6" 100FA10S6-PE 94820006 20.49 34
100 15 9 6" 100FA51S6-PE 94820009 26.31 38
20 13 6" 100FA20S6-PE 94820013 34.07 43
25 16 6" 100FA25S6-PE 94820016 39.94 47
5 2 4" & 6" 125FA5S6-PE 94822502 12.94 29
7.5 3 4" & 6" 125FA7S6-PE 94822503 15.05 30
10 4 4" & 6" 125FA10S6-PE 94822504 17.13 31
15 7 6" 125FA15S6-PE 94822507 23.37 35
125 20 9 6" 125FA20S6-PE 94822509 27.54 38
25 11 6" 125FA25S6-PE 94822511 31.70 40
30 13 6" 125FA30S6-PE 94822513 35.87 43
40 18 6" 125FA40S6-PE 94822518 46.27 48
Note: All dimensions are in inches. Discharge is 3" NPT. Maximum diameter across cable
guard is 5.5" on all models. Weight in pounds.
FEET
PSI
70
250 10 HP
350
800
60
225
300 700
200
50
600 7.5 HP
175 250
EFFICIENCY%
40
150 500
200
5 HP
125 400
30
150
100
300
3 HP
20
75 100
2 HP
200
50 1.5 HP
50 10
100
25
0 0 0
0 10 20 30 40 50 60 70 80 90 GPM
0 2 4 6 8 10 12 14 16 18 20 22 M3PH
4400
Submersible Pumps
6” High Capacity
50 GPM Performance Chart
Shut-off 158 ft
20 59 48 36 20
1.5 30 47 34 14
40 32 10
50
Shut-off PSI 51 42 34 25 16 8
0 79 74 68 63 56 48 39 30 11
Shut-off 210 ft
20 66 61 54 45 37 25
30 60 53 45 34 22
2 40 52 43 34 20
50 42 33 19
60 30 12
Shut-off PSI 74 65 56 48 39 30 22 13 4
0 - 78 74 70 65 58 55 49 41 15
Shut-off 263 ft
20 72 68 64 58 54 47 38 33 20
30 67 63 57 52 45 38 30 15
3 40 61 57 51 45 38 29 14
50 56 49 45 37 29 14
60 48 41 35 25 12
Shut-off PSI 97 88 79 71 62 53 45 36 27 6
0 - - - 78 75 73 70 67 64 55 45 34 12
Shut-off 420 ft
20 - 77 74 72 69 66 63 57 56 45 34 16
30 77 74 71 68 65 62 59 56 52 41 25
5 40 74 71 67 65 62 59 55 50 46 36 16
50 71 67 64 62 58 54 50 46 42 27
60 67 65 60 57 53 50 45 41 36 19
Shut-off PSI 164 156 147 139 130 121 113 104 95 74 52 30 9
0 - - - - - 78 76 74 72 67 62 57 49 42 29 16
Shut-off 592 ft
20 - - 79 78 75 74 72 70 68 62 57 49 41 30 17
30 - 79 77 75 73 71 70 68 65 60 53 47 37 26 12
7.5 40 79 77 74 73 71 69 67 65 62 57 49 42 29 18
50 76 74 72 71 70 67 65 62 60 54 47 37 26 14
60 74 72 70 69 67 65 61 60 58 52 45 32 19
Shut-off PSI 239 230 222 213 204 196 187 178 170 148 126 105 83 61 40 18
0 - - - - - - - 79 77 74 70 67 63 58 55 49 45 36 28 17 6
Shut-off 807 ft
20 - - - - - 79 77 76 74 71 67 63 59 56 50 46 37 29 18 8
30 - - - - 78 77 75 74 72 70 65 61 57 52 47 40 29 27 14
10 40 - - - 78 76 75 73 72 71 67 64 60 54 49 43 36 29 18
50 - - 79 77 75 73 72 71 69 65 62 57 53 47 41 34 26 14
60 - 78 76 74 73 72 70 69 68 64 60 54 49 44 38 29 18
Shut-off PSI 332 323 315 306 297 289 280 272 263 241 220 198 176 155 133 111 90 68 46 25 3
Discharge tapping 3” FNPT.
Notes: 1. Performance shown does not include friction loss in the drop pipe.
2. All performance data is based on rated motor nameplate voltage.
FEET
70
PSI
EFFICIENCY%
375
25 hp
350 1200 60
450
325
450
300
1000 50
20 hp
275 400
250
350
800
225 15 hp
300
200
10 hp
150
200
125 7.5 hp
400
150
100
5 hp
75 100
200 3 hp
50
50
25
0 0 0
0 20 40 60 80 100 120 GPM
0 2 4 6 8 10 12 14 16 18 20 22 24 26 M3PH
4400
Submersible Pumps
6” High Capacity
75 GPM Performance Chart
Shut-off 163 ft
0 115 104 96 86 74 55
20 93 82 70 51
3 30 80 67 46
40 65 41
50 37
Shut-off PSI 53 45 36 27 19 10
0 - - 105 102 96 89 83 76 65
Shut-off 261 ft
20 105 100 93 88 82 73 65 52
30 99 92 87 80 72 64 49
5 40 92 88 79 69 62 45
50 85 76 69 62 44
60 77 68 58 42
Shut-off PSI 96 87 78 70 61 52 44 35 26
0 - - - - - 107 103 99 94 84 69 50
Shut-off 392 ft
20 - 109 105 100 97 94 90 85 79 71 50
30 108 104 100 97 93 88 83 78 69 63 40
7.5 40 108 104 99 96 93 88 83 77 73 51
50 103 100 96 92 87 82 75 70 63 40
60 100 95 91 85 80 75 69 63 55
Shut-off PSI 152 144 135 126 118 109 100 92 93 61 40 18
0 - - - - - - 110 106 104 97 88 77 65 48
Shut-off 460 ft
20 - - - - 109 106 103 99 96 88 79 66 48
30 - - - 108 106 102 99 96 93 84 74 60 40
10 40 - - 108 105 102 99 96 92 89 80 68 52
50 - 108 103 102 99 93 92 89 84 74 62 42
60 107 103 100 98 96 91 88 84 80 68 53
Shut-off PSI 202 193 184 176 167 158 150 141 132 111 89 67 46 24
0 - - - - -
- - - - 110 105 100 95 89 81 74 65 56 39
Shut-off 732 ft
20 - - - - -
- - - 110 105 101 94 89 81 76 67 58 41
30 - - - - -
- - - 110 104 98 92 86 80 72 66 49
15 40 - - - - -
- - 110 107 102 96 90 82 75 70 58 40
50 110 107 104 99 94 86 80 72 65 49 30
60 110 109 107 103 102 96 90 82 76 69 58 46
Shut-off PSI 300 291 282 274 265 256 248 239 230 209 187 165 144 122 101 79 57 36 14
0 - - - - - - - - - - - 110 106 103 98 92 88 83 78 69 63 54 40
Shut-off 939 ft
20 - - - - - - - - - - 110 106 102 98 91 89 84 78 72 64 58 44
30 - - - - - - - - - 110 109 105 98 94 90 86 80 75 69 61 50 35
20 40 - - - - - - - - - 110 107 102 98 91 88 84 79 72 68 55 45
50 - - - - - - - - 110 109 105 100 95 91 87 80 75 70 63 52 38
60 - - - - - - - - 110 107 102 98 93 88 84 80 73 66 58 45
Shut-off PSI 389 381 372 363 355 346 337 329 320 298 277 255 233 212 190 168 147 125 103 82 60 39 17
HP PSI 300 350 400 450 500 550 600 650 700 750 800 850 900 950 1000 1050 1100 1150
0 - - 110 107 102 99 96 94 91 86 83 78 75 71 65 58 51 38
Shut-off 1210 ft
FEET
PSI
25 hp
10 00 60
EFFICIENCY%
3 00
4 00
9 00
20 hp
8 00 50
3 00 7 00
2 00
6 00 15 hp
5 00
200
4 00 10 hp
100 7.5 hp
3 00
100
2 00
5 hp
1 00
0 0 0
0 20 40 60 80 10 0 12 0 14 0 GPM
M3PH
0 5 9 14 18 23 27 32
4400
Submersible Pumps
6” High Capacity
100 GPM Performance Chart
Shut-off 191 ft
20 138 127 115 98 78 54 15
30 125 113 95 75 49 6
5 40 110 92 71 44
50 89 68 38
60 64 32
70 26
Shut-off PSI 74 65 57 48 39 31 22 13 5
0 - - - - - 138 131 123 115 107 79 32
Shut-off 320 ft
20 - - - 136 129 121 113 104 94 82 37
30 - - 135 128 120 111 102 92 80 64 4
7.5 40 - 134 126 118 110 101 90 77 62 42
50 133 125 117 109 99 88 75 59 38 10
60 124 116 107 98 86 73 56 34 5
70 115 106 96 84 71 53 30
Shut-off PSI 130 121 113 104 95 87 78 69 61 52 30 9
0 - - - - - - 140 134 127 121 102 79 45
Shut-off 393 ft
20 - - - - 138 132 125 118 111 104 81 48
30 - - - 137 131 124 117 110 102 94 67 28
10 40 - - 136 130 123 116 109 101 92 83 51 2
50 - 135 129 122 115 108 100 91 81 70 31
60 134 128 121 114 107 99 90 80 68 54 7
70 127 120 113 105 97 88 78 66 52 35
Shut-off PSI 162 153 144 136 127 118 110 101 92 84 62 40 19
0 - - - - - - - - - - 133 123 111 98 82 61 32
Shut-off 590 ft
20 - - - - - - - - 138 134 123 112 100 83 62 34
30 - - - - - - - 137 133 129 118 107 93 75 51 19
15 40 - - - - - - 136 132 128 124 113 101 85 64 37
50 - - - - 140 136 132 128 124 119 108 94 76 53 21
60 - - - 139 135 131 127 123 119 114 102 86 66 39 3
70 - - 138 135 131 126 122 118 113 109 95 78 55 24
Shut-off PSI 247 238 230 221 212 204 195 186 178 169 147 126 104 82 61 39 17
0 - - - - - - - - - - - - 134 127 119 111 103 94 83 69 52 29
Shut-off 846 ft
20 - - - - - - - - - - - 134 127 120 112 104 94 83 70 53 31
30 - - - - - - - - - - 138 131 124 116 108 99 90 78 63 44 19
20 40 - - - - - - - - - - 135 128 120 112 104 95 84 71 55 33 4
50 - - - - - - - - - 139 132 124 117 109 100 90 79 64 45 21
60 - - - - - - - - 138 135 128 121 113 105 96 85 72 56 35 7
70 - - - - - - - 138 135 132 125 117 109 101 91 80 65 47 23
Shut-off PSI 358 349 340 332 323 314 306 297 289 280 258 237 215 193 172 150 128 107 85 63 42 20
0 - - - - - - - - - - - - - 135 130 124 118 111 104 96 88 78 67 54 37 17
Shut-off 1030 ft
FEET
PSI
40 hp
1200 70
500
EFFICIENCY%
1100
1000 60
300
400
90 0 30 hp
80 0 50
25 hp
300 700
200
20 hp
600
500 15 hp
200
40 0
100
30 0 10 hp
100 7.5 hp
200
5 hp
100
0 0 0
0 20 40 60 80 100 120 140 16 0 GPM
0 5 9 14 18 23 27 32 36 M3PH
20 153 131 95 34
30 126 88 12
5 40 82
50
60
70
Shut-off PSI 48 39 30 22 13 4
- 0 - - - 157 141 122 99 64
Shut-off 198 ft
6” High Capacity
125 GPM Performance Chart
Shut-off 263 ft
20 - - - - 151 139 125 109 88 54
30 - - - 150 137 122 106 84 47
10 40 - 159 148 135 120 103 79 39
50 157 146 132 118 100 74 30
60 144 130 115 97 69 21
70 128 113 93 64 10
Shut-off PSI 105 97 88 79 71 62 53 45 36 27 6
0 - - - - - - - - - - 151 134 112 81 28
Shut-off 467 ft
20 - - - - - - - - 158 152 135 114 84 34
30 - - - - - - - 158 151 145 126 102 65
15 40 - - - - - - 157 150 144 137 116 87 39
50 - - - - - 156 149 143 136 128 104 68 3
60 - - - - 155 148 142 134 126 117 89 44
70 - - 160 154 147 141 133 125 116 106 72 10
Shut-off PSI 185 176 168 159 150 142 133 124 116 94 72 51 29 7
0 - - - - - - - - - - - 155 143 129 113 92 59 5
Shut-off 601 ft
20 - - - - - - - - - - 156 144 130 114 93 62 10
30 - - - - - - - - - - 151 138 123 105 81 41
20 40 - - - - - - - - - 157 145 131 115 95 65 15
50 - - - - - - - - 157 152 139 124 107 83 45
60 - - - - - - - 156 151 146 132 117 97 68 20
70 - - - - - 160 155 150 145 140 125 108 85 49
Shut-off PSI 252 243 234 226 217 208 200 191 182 174 152 130 109 87 66 44 22 1
0 - - - - - - - - - - - - - 153 143 133 119 99 71 31
Shut-off 734 ft
20 - - - - - - - - - - - - 154 144 134 120 101 74 35
30 - - - - - - - - - - - 159 149 140 128 112 90 57 13
25 40 - - - - - - - - - - - 155 145 135 121 103 76 38
50 - - - - - - - - - - 160 150 140 129 114 92 60 16
60 - - - - - - - - - - 155 146 135 123 105 78 42
70 - - - - - - - - - - 151 141 130 115 94 63 20
Shut-off PSI 292 283 275 266 257 249 240 231 210 188 166 145 123 102 80 58 37 15
0 - - - - - - - - - - - - - - 152 143 134 125 113 99 79 54 22
Shut-off 873 ft
20 - - - - - - - - - - - - - 153 144 135 126 114 100 81 56 25
30 - - - - - - - - - - - - 158 149 140 131 121 108 92 70 43 8
30 40 - - - - - - - - - - - - 153 145 136 126 115 101 83 58 27
50 - - - - - - - - - - - 158 149 141 132 122 109 93 72 45 10
60 - - - - - - - - - - - 154 145 137 127 116 102 84 61 30
70 - - - - - - - -- - - 159 150 141 132 122 110 95 74 47 13
Shut-off PSI 326 317 309 300 291 270 248 226 205 183 161 140 118 96 75 53 31
0 - - - - - - - - - - - - - - - - - 156 150 144 138 132 125 117 107 96 80
20 - - - - - - - - - - - - - - - - 156 150 145 139 132 126 118 108 97 82 62 Shut-off 1194 ft
30 - - - - - - - - - - - - - - - 160 154 148 142 136 129 122 114 103 90 73 52
40 40 - - - - - - - - - - - - - - - 157 151 145 139 133 126 118 109 98 83 64 40
50 - - - - - - - - - - - - - - - 154 148 142 136 130 123 114 104 91 75 54 26
60 - - - - - - - - - - - - - - 157 151 145 140 133 127 119 110 98 84 66 42 11
70 - - - - - - - - - - - - - - 155 149 143 137 130 123 115 105 92 76 55 29
Shut-off PSI 409 387 365 344 322 300 279 257 235 214 192 171
Features:
■ 100% Franklin factory tested.
■ Ductile iron discharge and suction bracket.
■ Ductile iron bowls bolt together for easy service.
■ Stainless upthrust bolt provides exceptional upthrust protection.
■ Bronze discharge bearing is grease packed for maximum bearing protection.
■ Fluted rubber bearings in all bowls.
■ Suction inlet located above bottom bearing prevents abrasives from entering
the bearing.
■ Suction bracket design allows easy access to coupling.
■ Bronze bracket bearing is protected with stainless steel sand collar.
■ Stainless steel impellers with stainless steel taper lock secures
impeller to shaft.
■ Stainless steel pump shaft for increased durability.
■ Shaft coupling is keyed to pump by set screws and is splined to fit
Model Number Explanation motor shaft.
Example: 175ST10D6B-0464 ■ All models have 6” motor fit.
175 = GPM ■ 4” Discharge tapping FNPT.
ST = Sub Turbine
10 = Horsepower
D = Ductile Iron
6 = 6” Pump
B = Impeller Trim
04 = Number of stages
6 = 6” Motor
4 = 4” Discharge
Submersible Turbine Pumps
PAGE: SP-203
Model 100ST6 Performance DATE: Mar 1, 2009
Meters
Feet
70
Efficiency (%)
200 650 15 hp 65
600 60
180
3450 rpm
550
160
500
140
450
10 hp
120 400
350
7.5 hp
100
300
80
250
5 hp
60 200
150
40
10 FT
100
4 GPM
20
50
0 0
0 20 40 60 80 100 120 140 US GPM
0 5 10 15 20 25 30 M3PH
Dimension Information
5.88
Motor P M* MD* Motor Wt Pump Wt
HP Stages Trim
Size Inches Inches Inches Lbs. Lbs.
5 3 B 6” 27.32 22.90 5.38 101 71
7.5 5 B 6” 34.32 24.20 5.38 108 91
P
10 6 1A, 5B 6” 37.82 25.40 5.38 116 101
15 10 B 6” 51.82 28.00 5.38 129 141
Note: *MD diameter = Franklin Electric Motor, M = Maximum Length of Franklin Electric Motor
Specifications
Minimum Well I.D. 6”
Minimum Submergence Above Inlet 10 Feet M
Discharge 4” NPT
Standard: 350 psi
Maximum Working Pressure Double Bolted: 675 psi
Note: Refer to Franklin Electric AIM data for motor cooling requirements.
MD
Materials of Construction
Part Name Common Material Name Material Spec Number
Discharge Bracket Ductile Iron A536 65-45-12
Top Bowl Ductile Iron A536 65-45-12
Intermediate Bowl Ductile Iron A536 65-45-12
Bearings, Disch. & Suction Bronze B505 C932
Impeller Stainless Steel A743 CF-8
Pump Shaft Stainless Steel A582 416
Suction Bracket Ductile Iron A536 65-45-12
Bowl Bearing Rubber Nitrile
Sand Collar Stainless Steel A276
Suction Screen Stainless Steel A666
Cable Guard Stainless Steel A666
Shaft Coupling Stainless Steel A276
Upthrust Bolt Stainless Steel A320 304
Taper Lock Stainless Steel A276
Bolting Stainless Steel A320 304
PAGE: SP-205
Model 100ST6 Performance DATE: Mar 1, 2009
Meters
Feet
70
Efficiency (%)
500
1600 65
40 hp
1500 60
450
3450 rpm
1400
400 1300
1200
30 hp
350
1100
25 hp
1000
300
900
250
800
20 hp
700
200
20 FT
600
4 GPM
150 500
400
0 20 40 60 80 100 120 140 US GPM
0 5 10 15 20 25 30 M3PH
Dimension Information
5.88
Motor P M* MD* Motor Wt Pump Wt
HP Stages Trim
Size Inches Inches Inches Lbs. Lbs.
20 10 9A, 1B 6” 51.82 30.60 5.38 145 141
25 14 7A, 7B 6” 65.32 33.10 5.38 156 182
P
30 15 13A, 2B 6” 69.32 35.70 5.38 174 192
40 20 18A, 2B 6” 86.82 40.80 5.38 202 242
Note: *MD diameter = Franklin Electric Motor, M = Maximum Length of Franklin Electric Motor
Specifications
Minimum Well I.D. 6”
Minimum Submergence Above Inlet 10 Feet
Discharge 4” NPT M
Standard: 350 psi
Maximum Working Pressure Double Bolted: 675 psi
Note: Refer to Franklin Electric AIM data for motor cooling requirements.
MD
Materials of Construction
Part Name Common Material Name Material Spec Number
Discharge Bracket Ductile Iron A536 65-45-12
Top Bowl Ductile Iron A536 65-45-12
Intermediate Bowl Ductile Iron A536 65-45-12
Bearings, Disch. & Suction Bronze B505 C932
Impeller Stainless Steel A743 CF-8
Pump Shaft Stainless Steel A582 416
Suction Bracket Ductile Iron A536 65-45-12
Bowl Bearing Rubber Nitrile
Sand Collar Stainless Steel A276
Suction Screen Stainless Steel A666
Cable Guard Stainless Steel A666
Shaft Coupling Stainless Steel A276
Upthrust Bolt Stainless Steel A320 304
Taper Lock Stainless Steel A276
Bolting Stainless Steel A320 304
PAGE: SP-207
Model 100ST6 Performance DATE: Mar 1, 2009
Feet
26 85
24 80 Trim A
1 FT
75
22
70 4 GPM
20 65
Trim B
18 60
55
16
50
Trim C
14
45 69%
12 40 64%
66%
35
10 68%
30
8 66%
25
Power (kW)
Power (hp)
64%
6 20
4 15
10
2 3.00
5 2.0
Trim A
0 0 2.25
Trim B
-5 1.50 1.0
-2
-10 Trim C 0.75
-4
-15 0.00 0.0
0 20 40 60 80 100 120
US GPM
0 5 10 15 20 25 30 M3PH
Note: Efficiencies are typical, not guaranteed. Efficiency correction required for low stage count (1 stage-6%, 2 stage-2%, 3 stage-1%)
Pumps are intentionally designed to utilize some portion of the motor's 1.15 service factor.
Bowl #9 begins transition to double-bolted (8 bolts @ bottom, 14 bolts @ top)
Nominal RPM: 3450
A Impeller Dimensions
C Trim A Diameter C Angle
A 4.688” 5°
B 4.200” 0°
C 3.688” 0°
PAGE: SP-209
Model 150ST6 Performance DATE: Mar 1, 2009
Meters
Feet
75
180
Efficiency (%)
550
20 hp 70
160 3450 rpm
500 65
140
450 60
15 hp
120 400
350
100
10 hp
300
80
250
7.5 hp
60 200
150
5 hp
40
10 FT
100
5 GPM
20
50
0 0
0 25 50 75 100 125 150 175 200 225 US GPM
0 5 10 15 20 25 30 35 40 45 50 M3PH
Dimension Information
5.88
Motor P M* MD* Motor Wt Pump Wt
HP Stages Trim
Size Inches Inches Inches Lbs. Lbs.
5 2 1A, 1B 6” 26.32 22.90 5.38 101 64
7.5 3 2A, 1B 6” 31.07 24.20 5.38 108 76
P
10 5 B 6” 40.57 25.40 5.38 116 88
15 6 4A, 2B 6” 45.27 28.00 5.38 129 107
20 7 A 6” 50.02 30.60 5.38 135 119
Note: *MD diameter = Franklin Electric Motor, M = Maximum Length of Franklin Electric Motor
Specifications
Minimum Well I.D. 6”
Minimum Submergence Above Inlet 10 Feet M
Discharge 4” NPT
Standard: 350 psi
Maximum Working Pressure Double Bolted: 675 psi
Note: Refer to Franklin Electric AIM data for motor cooling requirements.
MD
Materials of Construction
Part Name Common Material Name Material Spec Number
Discharge Bracket Ductile Iron A536 65-45-12
Top Bowl Ductile Iron A536 65-45-12
Intermediate Bowl Ductile Iron A536 65-45-12
Bearings, Disch. & Suction Bronze B505 C932
Impeller Stainless Steel A743 CF-8
Pump Shaft Stainless Steel A582 416
Suction Bracket Ductile Iron A536 65-45-12
Bowl Bearing Rubber Nitrile
Sand Collar Stainless Steel A276
Suction Screen Stainless Steel A666
Cable Guard Stainless Steel A666
Shaft Coupling Stainless Steel A276
Upthrust Bolt Stainless Steel A320 304
Taper Lock Stainless Steel A276
Bolting Stainless Steel A320 304
PAGE: SP-211
Model 150ST6 Performance DATE: Mar 1, 2009
Meters
Feet
75
450
Efficiency (%)
1400 70
50 hp
3450 rpm
400 1300 65
1200 60
350
40 hp
1100
1000
300
900
30 hp
250
800
700
25 hp
200
600
150 500
20 FT
400
5 GPM
100
300
200
0 25 50 75 100 125 150 175 200 225 US GPM
0 5 10 15 20 25 30 35 40 45 50 M3PH
Dimension Information
5.88
Motor P M* MD* Motor Wt Pump Wt
HP Stages Trim
Size Inches Inches Inches Lbs. Lbs.
25 9 A 6” 59.57 33.10 5.38 148 143
30 11 10A, 1B 6” 69.57 35.70 5.38 162 167
P
40 15 14A, 1B 6” 88.02 40.80 5.38 195 215
50 18 A 6” 102.32 57.80 5.38 310 250
Note: *MD diameter = Franklin Electric Motor, M = Maximum Length of Franklin Electric Motor
Specifications
Minimum Well I.D. 6”
Minimum Submergence Above Inlet 10 Feet
Discharge 4” NPT M
Standard: 350 psi
Maximum Working Pressure Double Bolted: 675 psi
Note: Refer to Franklin Electric AIM data for motor cooling requirements.
MD
Materials of Construction
Part Name Common Material Name Material Spec Number
Discharge Bracket Ductile Iron A536 65-45-12
Top Bowl Ductile Iron A536 65-45-12
Intermediate Bowl Ductile Iron A536 65-45-12
Bearings, Disch. & Suction Bronze B505 C932
Impeller Stainless Steel A743 CF-8
Pump Shaft Stainless Steel A582 416
Suction Bracket Ductile Iron A536 65-45-12
Bowl Bearing Rubber Nitrile
Sand Collar Stainless Steel A276
Suction Screen Stainless Steel A666
Cable Guard Stainless Steel A666
Shaft Coupling Stainless Steel A276
Upthrust Bolt Stainless Steel A320 304
Taper Lock Stainless Steel A276
Bolting Stainless Steel A320 304
PAGE: SP-213
Model 150ST6 Performance DATE: Mar 1, 2009
Feet
80 Trim A
24
75
22
1 FT
70
20 65 68%
Trim B 69% 5 GPM
60 70%
18
55 70%
16 69%
50 68%
71%
14 45
Trim C
12 40
35
10
30
8 25
Power (kW)
Power (hp)
6 20
15
4
10
2 4.00
5
0 0 3.00
Trim A 2.0
-5 2.00
-2
Trim B 1.0
-10 1.00
-4 Trim C
-15 0.00 0.0
0 25 50 75 100 125 150 175 200 US GPM
0 5 10 15 20 25 30 35 40 45 50 M3PH
Note: Efficiencies are typical, not guaranteed. Efficiency correction required for low stage count (1 stage-6%, 2 stage-3%, 3 stage-1%)
Pumps are intentionally designed to utilize some portion of the motor's 1.15 service factor.
Bowl #9 begins transition to double-bolted (8 bolts @ bottom, 14 bolts @ top)
Nominal RPM: 3450
A Impeller Dimensions
C Trim A Diameter C Angle
A 4.688” 27 °
B 4.250” 27 °
C 3.750” 27 °
PAGE: SP-215
Model 175ST6 Performance DATE: Mar 1, 2009
Meters
Feet
70
180
Efficiency (%)
550 65
160 20 hp
500 60
3450 rpm
140
450
15 hp
120 400
350
100
300
10 hp
80
250
60 200
7.5 hp
150
40
10 FT
100
5 hp
5 GPM
20
50
0 0
0 25 50 75 100 125 150 175 200 225 250 US GPM
0 5 10 15 20 25 30 35 40 45 50 55 M3PH
Dimension Information
5.88
Motor P M* MD* Motor Wt Pump Wt
HP Stages Trim
Size Inches Inches Inches Lbs. Lbs.
5 2 B 6” 26.32 22.90 5.38 101 65
7.5 3 B 6” 31.07 24.20 5.38 108 77
P
10 4 1A, 3B 6” 35.82 25.40 5.38 116 89
15 6 2A, 4B 6” 45.32 28.00 5.38 129 114
20 7 5A, 2B 6” 50.02 30.56 5.38 135 126
Note: *MD diameter = Franklin Electric Motor, M = Maximum Length of Franklin Electric Motor
Specifications
Minimum Well I.D. 6”
Minimum Submergence Above Inlet 10 Feet M
Discharge 4” NPT
Standard: 350 psi
Maximum Working Pressure Double Bolted: 675 psi
Note: Refer to Franklin Electric AIM data for motor cooling requirements.
MD
Materials of Construction
Part Name Common Material Name Material Spec Number
Discharge Bracket Ductile Iron A536 65-45-12
Top Bowl Ductile Iron A536 65-45-12
Intermediate Bowl Ductile Iron A536 65-45-12
Bearings, Disch. & Suction Bronze B505 C932
Impeller Stainless Steel A743 CF-8
Pump Shaft Stainless Steel A582 416
Suction Bracket Ductile Iron A536 65-45-12
Bowl Bearing Rubber Nitrile
Sand Collar Stainless Steel A276
Suction Screen Stainless Steel A666
Cable Guard Stainless Steel A666
Shaft Coupling Stainless Steel A276
Upthrust Bolt Stainless Steel A320 304
Taper Lock Stainless Steel A276
Bolting Stainless Steel A320 304
PAGE: SP-217
Model 175ST6 Performance DATE: Mar 1, 2009
Meters
Feet
70
Efficiency (%)
1500 60 hp 65
450
1400 60
3450 rpm
400 1300
50 hp
1200
350
1100
40 hp
300 1000
900
250
800
700 30 hp
200
600
25 hp
150 500
20 FT
400
5 GPM
100
300
200
0 25 50 75 100 125 150 175 200 225 250 US GPM
0 5 10 15 20 25 30 35 40 45 50 55 M3PH
Dimension Information
5.88
Motor P M* MD* Motor Wt Pump Wt
HP Stages Trim
Size Inches Inches Inches Lbs. Lbs.
25 8 A 6” 54.82 33.10 5.38 148 138
30 10 9A, 1B 6” 64.27 35.70 5.38 162 162
P
40 13 A 6” 78.52 40.80 5.38 195 199
50 16 A 6” 92.82 57.80 5.38 310 235
60 19 A 6” 107.07 63.80 5.38 340 271
Note: *MD diameter = Franklin Electric Motor, M = Maximum Length of Franklin Electric Motor
Specifications
Minimum Well I.D. 6”
Minimum Submergence Above Inlet 10 Feet
Discharge 4” NPT M
Standard: 350 psi
Maximum Working Pressure Double Bolted: 675 psi
Note: Refer to Franklin Electric AIM data for motor cooling requirements.
MD
Materials of Construction
Part Name Common Material Name Material Spec Number
Discharge Bracket Ductile Iron A536 65-45-12
Top Bowl Ductile Iron A536 65-45-12
Intermediate Bowl Ductile Iron A536 65-45-12
Bearings, Disch. & Suction Bronze B505 C932
Impeller Stainless Steel A743 CF-8
Pump Shaft Stainless Steel A582 416
Suction Bracket Ductile Iron A536 65-45-12
Bowl Bearing Rubber Nitrile
Sand Collar Stainless Steel A276
Suction Screen Stainless Steel A666
Cable Guard Stainless Steel A666
Shaft Coupling Stainless Steel A276
Upthrust Bolt Stainless Steel A320 304
Taper Lock Stainless Steel A276
Bolting Stainless Steel A320 304
PAGE: SP-219
Model 175ST6 Performance DATE: Mar 1, 2009
Feet
24 80
75
22
Trim A
1 FT
70
66% 67%
20 65 68% 5 GPM
69%
18 60 70%
Trim B
55
16 69%
50 68%
67%
14 45 66%
40
Trim C
12
35
10
30
8 25
Power (kW)
Power (hp)
6 20
15
4
10
2 4.00
5
0 0 Trim A 3.00
2.0
Trim B 2.00
-2
1.0
Trim C 1.00
-4
0.00 0.0
0 25 50 75 100 125 150 175 200 225 250 US GPM
0 5 10 15 20 25 30 35 40 45 50 55 60 M3PH
Note: Efficiencies are typical, not guaranteed. Efficiency correction required for low stage count (1 stage-6%, 2 stage-2%, 3 stage-1%)
Pumps are intentionally designed to utilize some portion of the motor's 1.15 service factor.
Bowl #9 begins transition to double-bolted (8 bolts @ bottom, 14 bolts @ top)
Nominal RPM: 3450
A Impeller Dimensions
C Trim A Diameter C Angle
A 4.688” 20 °
B 4.250” 20 °
C 3.750” 20 °
PAGE: SP-221
Model 200ST6 Performance DATE: Mar 1, 2009
Meters
Feet
Efficiency (%)
70
120
375 65
110
350 20 hp 60
3450 rpm
100 325
90 300
15 hp
275
80
250
70
225
10 hp
60 200
175
50
150
7.5 hp
40
125
30 100
5 hp
75
20
50 5 FT
10 5 GPM
25
0 0
0 25 50 75 100 125 150 175 200 225 250 275 300 325 US GPM
0 10 20 30 40 50 60 70 M3PH
Dimension Information
5.88
Motor P M* MD* Motor Wt Pump Wt
HP Stages Trim
Size Inches Inches Inches Lbs. Lbs.
5 1 A 6” 21.57 22.90 5.38 101 53
7.5 2 B 6” 26.32 24.20 5.38 108 66
P
10 3 2B, 1C 6” 31.02 25.40 5.38 116 78
15 4 1A, 3B 6” 35.82 28.00 5.38 129 90
20 5 3A, 2B 6” 40.57 30.60 5.38 135 103
Note: *MD diameter = Franklin Electric Motor, M = Maximum Length of Franklin Electric Motor
Specifications
Minimum Well I.D. 6”
Minimum Submergence Above Inlet 10 Feet M
Discharge 4” NPT
Standard: 350 psi
Maximum Working Pressure Double Bolted: 675 psi
Note: Refer to Franklin Electric AIM data for motor cooling requirements.
MD
Materials of Construction
Part Name Common Material Name Material Spec Number
Discharge Bracket Ductile Iron A536 65-45-12
Top Bowl Ductile Iron A536 65-45-12
Intermediate Bowl Ductile Iron A536 65-45-12
Bearings, Disch. & Suction Bronze B505 C932
Impeller Stainless Steel A743 CF-8
Pump Shaft Stainless Steel A582 416
Suction Bracket Ductile Iron A536 65-45-12
Bowl Bearing Rubber Nitrile
Sand Collar Stainless Steel A276
Suction Screen Stainless Steel A666
Cable Guard Stainless Steel A666
Shaft Coupling Stainless Steel A276
Upthrust Bolt Stainless Steel A320 304
Taper Lock Stainless Steel A276
Bolting Stainless Steel A320 304
PAGE: SP-223
Model 200ST6 Performance DATE: Mar 1, 2009
Meters
Feet
Efficiency (%)
70
320 1050 65
60 hp
1000 60
300
950 3450 rpm
280
900
50 hp
260 850
800
240
750
220
700
200 650
40 hp
180 600
550
160
500
30 hp
140 450
25 hp
120 400
350
100
300 10 FT
80 5 GPM
250
200
0 25 50 75 100 125 150 175 200 225 250 275 300 325 US GPM
0 10 20 30 40 50 60 70 M3PH
Dimension Information
5.88
Motor P M* MD* Motor Wt Pump Wt
HP Stages Trim
Size Inches Inches Inches Lbs. Lbs.
25 6 A 6” 45.32 33.10 5.38 148 115
30 7 A 6” 50.07 35.70 5.38 162 128
P
40 9 A 6” 59.57 40.80 5.38 195 152
50 12 A 6” 73.82 57.80 5.38 310 189
60 14 A 6” 83.32 63.80 5.38 340 214
Note: *MD diameter = Franklin Electric Motor, M = Maximum Length of Franklin Electric Motor
Specifications
Minimum Well I.D. 6”
Minimum Submergence Above Inlet 10 Feet
Discharge 4” NPT M
Standard: 350 psi
Maximum Working Pressure Double Bolted: 675 psi
Note: Refer to Franklin Electric AIM data for motor cooling requirements.
MD
Materials of Construction
Part Name Common Material Name Material Spec Number
Discharge Bracket Ductile Iron A536 65-45-12
Top Bowl Ductile Iron A536 65-45-12
Intermediate Bowl Ductile Iron A536 65-45-12
Bearings, Disch. & Suction Bronze B505 C932
Impeller Stainless Steel A743 CF-8
Pump Shaft Stainless Steel A582 416
Suction Bracket Ductile Iron A536 65-45-12
Bowl Bearing Rubber Nitrile
Sand Collar Stainless Steel A276
Suction Screen Stainless Steel A666
Cable Guard Stainless Steel A666
Shaft Coupling Stainless Steel A276
Upthrust Bolt Stainless Steel A320 304
Taper Lock Stainless Steel A276
Bolting Stainless Steel A320 304
PAGE: SP-225
Model 200ST6 Performance DATE: Mar 1, 2009
Feet
24 80
Trim A
75
22
Trim B
1 FT
70
65%
20 65 67%
Trim C 5 GPM
18 60 69%
55
16
50 67%
14 66% 65%
45
68%
12 40
68%
35
10 66%
30
8 25
Power (kW)
Power (hp)
6 20
15
4
10
2 Trim A 5.00
5
0 0 4.00 3.0
Trim B
3.00
-2 Trim C 2.0
2.00
-4 1.0
1.00
0 25 50 75 100 125 150 175 200 225 250 275 US GPM
0 5 10 15 20 25 30 35 40 45 50 55 60 65 M3PH
Note: Efficiencies are typical, not guaranteed. Efficiency correction required for low stage count (1 stage-6%, 2 stage-2%)
Pumps are intentionally designed to utilize some portion of the motor's 1.15 service factor.
Bowl #9 begins transition to double-bolted (8 bolts @ bottom, 14 bolts @ top)
Nominal RPM: 3450
A Impeller Dimensions
C Trim A Diameter C Angle
A 4.625” 30 °
B 4.438” 30 °
C 4.250” 30 °
PAGE: SP-227
Model 225ST6 Performance DATE: Mar 1, 2009
Meters
Feet
75
160
Efficiency (%)
500
20 hp 70
3450 rpm
140
450 65
120 400 60
15 hp
350
100
300
80 10 hp
250
60 200
7.5 hp
150
40 5 hp
10 FT
100
5 GPM
20
50
0 0
0 25 50 75 100 125 150 175 200 225 250 275 300 325 US GPM
0 10 20 30 40 50 60 70 M3PH
Dimension Information
5.88
Motor P M* MD* Motor Wt Pump Wt
HP Stages Trim
Size Inches Inches Inches Lbs. Lbs.
5 2 1A, 1B 6” 26.30 22.90 5.38 101 65
7.5 3 1A, 2B 6” 31.10 24.20 5.38 108 77
P
10 4 2A, 2B 6” 35.80 25.40 5.38 116 89
15 5 5A 6” 40.60 28.00 5.38 129 101
20 7 6A, 1B 6” 50.10 30.60 5.38 145 128
Note: *MD diameter = Franklin Electric Motor, M = Maximum Length of Franklin Electric Motor
Specifications
Minimum Well I.D. 6”
Minimum Submergence Above Inlet 10 Feet M
Discharge 4” NPT
Standard: 350 psi
Maximum Working Pressure Double Bolted: 675 psi
Note: Refer to Franklin Electric AIM data for motor cooling requirements.
MD
Materials of Construction
Part Name Common Material Name Material Spec Number
Discharge Bracket Ductile Iron A536 65-45-12
Top Bowl Ductile Iron A536 65-45-12
Intermediate Bowl Ductile Iron A536 65-45-12
Bearings, Disch. & Suction Bronze B505 C932
Impeller Stainless Steel A743 CF-8
Pump Shaft Stainless Steel A582 416
Suction Bracket Ductile Iron A536 65-45-12
Bowl Bearing Rubber Nitrile
Sand Collar Stainless Steel A276
Suction Screen Stainless Steel A666
Cable Guard Stainless Steel A666
Shaft Coupling Stainless Steel A276
Upthrust Bolt Stainless Steel A320 304
Taper Lock Stainless Steel A276
Bolting Stainless Steel A320 304
PAGE: SP-229
Model 225ST6 Performance DATE: Mar 1, 2009
Meters
Feet
75
50 hp
Efficiency (%)
1200 3450 rpm 70
350
1100 65
40 hp
1000 60
300
900
250
800
30 hp
700
200
25 hp
600
150 500
400
100
20 FT
300
5 GPM
200
50
100
0 25 50 75 100 125 150 175 200 225 250 275 300 325 US GPM
0 10 20 30 40 50 60 70 M3PH
Dimension Information
5.88
Motor P M* MD* Motor Wt Pump Wt
HP Stages Trim
Size Inches Inches Inches Lbs. Lbs.
25 9 7A, 2B 6” 59.56 33.10 5.38 156 149
30 11 8A, 3B 6” 69.10 35.70 5.38 174 172
P
40 14 13A, 1B 6” 83.30 40.80 5.38 202 204
50 17 17A 6” 97.60 55.30 5.38 300 238
Note: *MD diameter = Franklin Electric Motor, M = Maximum Length of Franklin Electric Motor
Specifications
Minimum Well I.D. 6”
Minimum Submergence Above Inlet 10 Feet
Discharge 4” NPT M
Standard: 350 psi
Maximum Working Pressure Double Bolted: 675 psi
Note: Refer to Franklin Electric AIM data for motor cooling requirements.
MD
Materials of Construction
Part Name Common Material Name Material Spec Number
Discharge Bracket Ductile Iron A536 65-45-12
Top Bowl Ductile Iron A536 65-45-12
Intermediate Bowl Ductile Iron A536 65-45-12
Bearings, Disch. & Suction Bronze B505 C932
Impeller Stainless Steel A743 CF-8
Pump Shaft Stainless Steel A582 416
Suction Bracket Ductile Iron A536 65-45-12
Bowl Bearing Rubber Nitrile
Sand Collar Stainless Steel A276
Suction Screen Stainless Steel A666
Cable Guard Stainless Steel A666
Shaft Coupling Stainless Steel A276
Upthrust Bolt Stainless Steel A320 304
Taper Lock Stainless Steel A276
Bolting Stainless Steel A320 304
PAGE: SP-231
Model 225ST6 Performance DATE: Mar 1, 2009
Feet
24
75
22 Trim A
70
20
1 FT
65 54%
60%
18 60
64% 5 GPM
55 Trim B 68%
16 70%
50
72%
14 45
72%
12 40
Trim C 70%
35 74% 68%
10
30 64%
8 60%
25
54%
6 20
Power (kW)
Power (hp)
15
4
10
2
5
0 0 4.0
Trim A
3.0
-2 2
2.0
-4 Trim B 1
1.0
Trim C
-6 0.0 0
0 25 50 75 100 125 150 175 200 225 250 275 300 325 US GPM
0 10 20 30 40 50 60 70 M3PH
Note: Efficiencies are typical, not guaranteed. No efficiency correction needed for low stage count pumps.
Pumps are intentionally designed to utilize some portion of the motor's 1.15 service factor.
Bowl #9 begins transition to double-bolted (8 bolts @ bottom, 14 bolts @ top)
Nominal RPM: 3450
A Impeller Dimensions
C Trim A Diameter C Angle
A 4.472” 25.5 °
B 3.972” 25.5 °
C 3.472” 25.5 °
PAGE: SP-233
Model 275ST6 Performance DATE: Mar 1, 2009
Meters
Feet
75
120
Efficiency (%)
375 70
110
20 hp
350 65
100 325 60
90 300
15 hp 3450 rpm
275
80
250
70
225
10 hp
60 200
175
50
150
40 7.5 hp
125
30 100
75
20
5 hp
50 5 FT
10 10 GPM
25
0 0
0 50 100 150 200 250 300 350 400 US GPM
0 10 20 30 40 50 60 70 80 90 M3PH
Dimension Information
5.88
Motor P M* MD* Motor Wt Pump Wt
HP Stages Trim
Size Inches Inches Inches Lbs. Lbs.
5 1 1A 6” 21.57 22.90 5.38 101 53
7.5 2 2A 6” 26.32 24.20 5.38 108 66
P
10 3 2A, 1B 6” 31.07 25.40 5.38 116 77
15 4 4A 6” 35.82 28.00 5.38 129 90
20 5 5A 6” 40.57 30.60 5.38 145 105
Note: *MD diameter = Franklin Electric Motor, M = Maximum Length of Franklin Electric Motor
Specifications
Minimum Well I.D. 6”
Minimum Submergence Above Inlet 10 Feet M
Discharge 4” NPT
Standard: 350 psi
Maximum Working Pressure Double Bolted: 675 psi
Note: Refer to Franklin Electric AIM data for motor cooling requirements.
MD
Materials of Construction
Part Name Common Material Name Material Spec Number
Discharge Bracket Ductile Iron A536 65-45-12
Top Bowl Ductile Iron A536 65-45-12
Intermediate Bowl Ductile Iron A536 65-45-12
Bearings, Disch. & Suction Bronze B505 C932
Impeller Stainless Steel A743 CF-8
Pump Shaft Stainless Steel A582 416
Suction Bracket Ductile Iron A536 65-45-12
Bowl Bearing Rubber Nitrile
Sand Collar Stainless Steel A276
Suction Screen Stainless Steel A666
Cable Guard Stainless Steel A666
Shaft Coupling Stainless Steel A276
Upthrust Bolt Stainless Steel A320 304
Taper Lock Stainless Steel A276
Bolting Stainless Steel A320 304
PAGE: SP-235
Model 275ST6 Performance DATE: Mar 1, 2009
Meters
Feet
75
Efficiency (%)
1200 70
350
60 hp
1100 65
1000 60
300
3450 rpm
50 hp
900
250
800
40 hp
700
200
600
30 hp
150 500
25 hp
400
100
20 FT
300
10 GPM
200
50
100
0 50 100 150 200 250 300 350 400 US GPM
0 10 20 30 40 50 60 70 80 90 M3PH
Dimension Information
5.88
Motor P M* MD* Motor Wt Pump Wt
HP Stages Trim
Size Inches Inches Inches Lbs. Lbs.
25 7 6A, 1B 6” 50.10 33.10 5.38 156 125
30 8 8A 6” 54.80 35.70 5.38 174 138
P
40 11 10A, 1B 6” 69.10 40.80 5.38 202 172
50 14 12A, 2B 6” 83.30 55.30 5.38 300 214
60 16 16A 6” 92.80 61.30 5.38 330 235
Note: *MD diameter = Franklin Electric Motor, M = Maximum Length of Franklin Electric Motor
Specifications
Minimum Well I.D. 6”
Minimum Submergence Above Inlet 10 Feet
Discharge 4” NPT M
Standard: 350 psi
Maximum Working Pressure Double Bolted: 675 psi
Note: Refer to Franklin Electric AIM data for motor cooling requirements.
MD
Materials of Construction
Part Name Common Material Name Material Spec Number
Discharge Bracket Ductile Iron A536 65-45-12
Top Bowl Ductile Iron A536 65-45-12
Intermediate Bowl Ductile Iron A536 65-45-12
Bearings, Disch. & Suction Bronze B505 C932
Impeller Stainless Steel A743 CF-8
Pump Shaft Stainless Steel A582 416
Suction Bracket Ductile Iron A536 65-45-12
Bowl Bearing Rubber Nitrile
Sand Collar Stainless Steel A276
Suction Screen Stainless Steel A666
Cable Guard Stainless Steel A666
Shaft Coupling Stainless Steel A276
Upthrust Bolt Stainless Steel A320 304
Taper Lock Stainless Steel A276
Bolting Stainless Steel A320 304
PAGE: SP-237
Model 275ST6 Performance DATE: Mar 1, 2009
Feet
24
75
22
70
Trim A
20 65
1 FT
60 62%
18 65% 10 GPM
68%
55 Trim B 70%
16 72%
50
14 74%
45
Trim C
12 40 72%
70%
35 68%
10 65%
30 62%
8 25
Power (kW)
Power (hp)
6 20
15
4
10
2
5 5.0
0 0 4.0 3
Trim A
3.0
-2 2
Trim B
2.0
-4 Trim C 1
1.0
0 50 100 150 200 250 300 350
US GPM
0 10 20 30 40 50 60 70 80 90 M3PH
Note: Efficiencies are typical, not guaranteed. No efficiency correction needed for low stage count pumps.
Pumps are intentionally designed to utilize some portion of the motor's 1.15 service factor.
Bowl #9 begins transition to double-bolted (8 bolts @ bottom, 14 bolts @ top)
Nominal RPM: 3450
A Impeller Dimensions
C Trim A Diameter C Angle
A 4.568” 17 °
B 4.193” 17 °
C 3.818” 17 °
PAGE: SP-239
Model 325ST6 Performance DATE: Mar 1, 2009
Meters
Feet
400 70
120
Efficiency (%)
350 65
100
20 hp
300 60
80
250 55
15 hp 3450 rpm
60 200
10 hp
150
40 7.5 hp
10 FT
100
5 hp 10 GPM
20
50
0 0
0 50 100 150 200 250 300 350 400 450 US GPM
0 20 40 60 80 100 M3PH
Dimension Information
5.88
Motor P M* MD* Motor Wt Pump Wt
HP Stages Trim
Size Inches Inches Inches Lbs. Lbs.
5 2 C 6” 26.32 22.90 5.38 101 65
7.5 2 1A, 1B 6” 26.32 24.20 5.38 108 65
P
10 3 B 6” 31.07 25.40 5.38 116 77
15 4 3A, 1C 6” 35.82 28.00 5.38 129 89
20 5 A 6” 40.57 30.60 5.38 135 101
Note: *MD diameter = Franklin Electric Motor, M = Maximum Length of Franklin Electric Motor
Specifications
Minimum Well I.D. 6”
Minimum Submergence Above Inlet 10 Feet M
Discharge 4” NPT
Standard: 350 psi
Maximum Working Pressure Double Bolted: 675 psi
Note: Refer to Franklin Electric AIM data for motor cooling requirements.
MD
Materials of Construction
Part Name Common Material Name Material Spec Number
Discharge Bracket Ductile Iron A536 65-45-12
Top Bowl Ductile Iron A536 65-45-12
Intermediate Bowl Ductile Iron A536 65-45-12
Bearings, Disch. & Suction Bronze B505 C932
Impeller Stainless Steel A743 CF-8
Pump Shaft Stainless Steel A582 416
Suction Bracket Ductile Iron A536 65-45-12
Bowl Bearing Rubber Nitrile
Sand Collar Stainless Steel A276
Suction Screen Stainless Steel A666
Cable Guard Stainless Steel A666
Shaft Coupling Stainless Steel A276
Upthrust Bolt Stainless Steel A320 304
Taper Lock Stainless Steel A276
Bolting Stainless Steel A320 304
PAGE: SP-241
Model 325ST6 Performance DATE: Mar 1, 2009
Meters
Feet
1100 70
320
60 hp
Efficiency (%)
1000 65
280
900 60
50 hp
800 55
240
3450 rpm
700
200
600
40 hp
160
500
30 hp
120 400
25 hp
20 FT
300
80 10 GPM
200
40
100
0 50 100 150 200 250 300 350 400 450 US GPM
0 20 40 60 80 100 M3PH
Dimension Information
5.88
Motor P M* MD* Motor Wt Pump Wt
HP Stages Trim
Size Inches Inches Inches Lbs. Lbs.
25 6 A 6” 45.32 33.10 5.38 148 113
30 7 A 6” 50.07 35.70 5.38 162 125
P
40 10 A 6” 64.32 40.80 5.38 195 161
50 12 A 6” 73.82 57.83 5.38 310 184
60 15 A 6” 88.07 63.83 5.38 340 220
Note: *MD diameter = Franklin Electric Motor, M = Maximum Length of Franklin Electric Motor
Specifications
Minimum Well I.D. 6”
Minimum Submergence Above Inlet 10 Feet
Discharge 4” NPT M
Standard: 350 psi
Maximum Working Pressure Double Bolted: 675 psi
Note: Refer to Franklin Electric AIM data for motor cooling requirements.
MD
Materials of Construction
Part Name Common Material Name Material Spec Number
Discharge Bracket Ductile Iron A536 65-45-12
Top Bowl Ductile Iron A536 65-45-12
Intermediate Bowl Ductile Iron A536 65-45-12
Bearings, Disch. & Suction Bronze B505 C932
Impeller Stainless Steel A743 CF-8
Pump Shaft Stainless Steel A582 416
Suction Bracket Ductile Iron A536 65-45-12
Bowl Bearing Rubber Nitrile
Sand Collar Stainless Steel A276
Suction Screen Stainless Steel A666
Cable Guard Stainless Steel A666
Shaft Coupling Stainless Steel A276
Upthrust Bolt Stainless Steel A320 304
Taper Lock Stainless Steel A276
Bolting Stainless Steel A320 304
PAGE: SP-243
Model 325ST6 Performance DATE: Mar 1, 2009
Feet
75
70 Trim A
20 65
1 FT
60
Trim B
10 GPM
55 57%
50 63%
15 67%
Trim C 69%
45 70%
71%
40 70%
69%
35 67%
10
30 63%
25 57%
Power (kW)
Power (hp)
20
5 15
10
5 5.0
0 0 Trim A 4.0
3
3.0
Trim B 2.0 2
Trim C 1
1.0
0.0 0
0 50 100 150 200 250 300 350 400
US GPM
0 20 40 60 80 100 M3PH
Note: Efficiencies are typical, not guaranteed. No efficiency correction needed for low stage count pumps.
Pumps are intentionally designed to utilize some portion of the motor's 1.15 service factor.
Bowl #9 begins transition to double-bolted (8 bolts @ bottom, 14 bolts @ top)
Nominal RPM: 3450
A Impeller Dimensions
C Trim A Diameter C Angle
A 4.500” 30 °
B 4.250” 30 °
C 4.000” 30 °
PAGE: SP-245
Model 375ST6 Performance DATE: Mar 1, 2009
Meters
Feet
75
Efficiency (%)
100 325 20 hp 70
300 65
90
275 60
80 15 hp 3450 rpm
250
70
225
60 200
175
50
150
10 hp
40
125
7.5 hp
30 100
75
20
5 hp
5 FT
50
10 GPM
10
25
0 0
0 50 100 150 200 250 300 350 400 450 500 US GPM
Dimension Information
5.88
Motor P M* MD* Motor Wt Pump Wt
HP Stages Trim
Size Inches Inches Inches Lbs. Lbs.
5 1 A 6” 21.57 22.90 5.38 101 53
7.5 2 B 6” 26.32 24.20 5.38 108 65
P
10 2 A 6” 26.32 25.40 5.38 116 65
15 4 B 6” 35.82 28.00 5.38 129 89
20 5 1A, 4B 6” 40.57 30.56 5.38 135 101
Note: *MD diameter = Franklin Electric Motor, M = Maximum Length of Franklin Electric Motor
Specifications
Minimum Well I.D. 6”
Minimum Submergence Above Inlet 10 Feet M
Discharge 4” NPT
Standard: 350 psi
Maximum Working Pressure Double Bolted: 675 psi
Note: Refer to Franklin Electric AIM data for motor cooling requirements.
MD
Materials of Construction
Part Name Common Material Name Material Spec Number
Discharge Bracket Ductile Iron A536 65-45-12
Top Bowl Ductile Iron A536 65-45-12
Intermediate Bowl Ductile Iron A536 65-45-12
Bearings, Disch. & Suction Bronze B505 C932
Impeller Stainless Steel A743 CF-8
Pump Shaft Stainless Steel A582 416
Suction Bracket Ductile Iron A536 65-45-12
Bowl Bearing Rubber Nitrile
Sand Collar Stainless Steel A276
Suction Screen Stainless Steel A666
Cable Guard Stainless Steel A666
Shaft Coupling Stainless Steel A276
Upthrust Bolt Stainless Steel A320 304
Taper Lock Stainless Steel A276
Bolting Stainless Steel A320 304
PAGE: SP-247
Model 375ST6 Performance DATE: Mar 1, 2009
Meters
Feet
75
300
Efficiency (%)
950 70
280
900 65
60 hp
260 850 60
800 55
240
750 50 hp
3450 rpm
220
700
200 650
40 hp
180 600
550
160
500
30 hp
140 450
400
25 hp
120
350
100
300
80
250
10 FT
60 200
10 GPM
150
40
100
0 50 100 150 200 250 300 350 400 450 500 US GPM
Dimension Information
5.88
Motor P M* MD* Motor Wt Pump Wt
HP Stages Trim
Size Inches Inches Inches Lbs. Lbs.
25 6 3A, 3B 6” 45.27 33.13 5.38 148 113
30 7 5A, 2B 6” 50.02 35.69 5.38 162 125
P
40 9 A 6” 59.57 40.81 5.38 195 149
50 11 A 6” 69.07 57.83 5.38 310 172
60 13 A 6” 78.57 63.83 5.38 340 196
Note: *MD diameter = Franklin Electric Motor, M = Maximum Length of Franklin Electric Motor
Specifications
Minimum Well I.D. 6”
Minimum Submergence Above Inlet 10 Feet
Discharge 4” NPT M
Standard: 350 psi
Maximum Working Pressure Double Bolted: 675 psi
Note: Refer to Franklin Electric AIM data for motor cooling requirements.
MD
Materials of Construction
Part Name Common Material Name Material Spec Number
Discharge Bracket Ductile Iron A536 65-45-12
Top Bowl Ductile Iron A536 65-45-12
Intermediate Bowl Ductile Iron A536 65-45-12
Bearings, Disch. & Suction Bronze B505 C932
Impeller Stainless Steel A743 CF-8
Pump Shaft Stainless Steel A582 416
Suction Bracket Ductile Iron A536 65-45-12
Bowl Bearing Rubber Nitrile
Sand Collar Stainless Steel A276
Suction Screen Stainless Steel A666
Cable Guard Stainless Steel A666
Shaft Coupling Stainless Steel A276
Upthrust Bolt Stainless Steel A320 304
Taper Lock Stainless Steel A276
Bolting Stainless Steel A320 304
PAGE: SP-249
Model 375ST6 Performance DATE: Mar 1, 2009
Feet
22 Trim A
70
20 65 Trim B
60
1 FT
18
55 10 GPM
16 Trim C 60%
50 64%
14 68%
45
72%
12 40
35
10 68%
30
64%
8 25 60%
6 20
Power (kW)
Power (hp)
15
4
10
2
5
Trim A 5.00
0 0 3.5
Trim B 3.0
4.00
-2
2.5
Trim C 3.00
2.0
-4
2.00 1.5
0 50 100 150 200 250 300 350 400 450 US GPM
Note: Efficiencies are typical, not guaranteed. Efficiency correction required for low stage count (1 stage-7%, 2 stage-4%, 3 stage-1%)
Pumps are intentionally designed to utilize some portion of the motor's 1.15 service factor.
Bowl #9 begins transition to double-bolted (8 bolts @ bottom, 14 bolts @ top)
Nominal RPM: 3450
A Impeller Dimensions
C Trim A Diameter C Angle
A 4.688” 35 °
B 4.440” 35 °
C 4.313” 35 °
Features:
■ 100% Franklin factory tested.
■ Ductile iron discharge and suction bracket.
■ Ductile iron bowls bolt together for easy service.
■ Epoxy coated bowls for improved efficiency.
■ Stainless upthrust bolt provides exceptional upthrust protection.
■ Bronze discharge bearing is grease packed for maximum bearing protection.
■ Fluted rubber bearings in all bowls.
■ Suction inlet located above bottom bearing prevents abrasives from entering
the bearing.
■ Suction bracket design allows easy access to coupling.
■ Bronze bracket bearing is protected with stainless steel sand collar.
■ Stainless steel impellers with stainless steel taper lock secures
impeller to shaft.
■ Stainless steel pump shaft for increased durability.
■ Shaft coupling is keyed to pump by set screws and is splined to fit
Model Number Explanation motor shaft.
Example: 225ST25D8B-0366
225 = GPM
ST = Sub Turbine
25 = Horsepower
D = Ductile Iron
8 = 8” Pump
B = Impeller Trim
03 = Number of stages
6 = Motor Size
6 = Discharge Size
Submersible Turbine Pumps
PAGE: SP-260
Model 225ST8 Performance DATE: Sept 1, 2007
600 70%
30 hp
500 65%
TOTAL DYNAMIC HEAD -FEET
25 hp
EFFICIENCY %
400 60%
20 hp
300 55%
15 hp
200 50%
7.5 hp
100 45%
0 40%
0 25 50 75 100 125 150 175 200 225 250 275 300 325
FLOWRATE - U.S. GALLONS PER MINUTE
2000 68%
100 hp
1800 64%
TOTAL DYNAMIC HEAD -FEET
1600 60%
EFFICIENCY %
1400 75 hp 56%
1200 52%
60 hp
1000 48%
50 hp
800 44%
600 40%
400 36%
0 25 50 75 100 125 150 175 200 225 250 275 300 325
FLOWRATE - U.S. GALLONS PER MINUTE
Specifications
M
Minimum Well I.D. 8”
Minimum Submergence @ BEP (above inlet) 10 Feet
Discharge 4” or 6” NPT
Note: Refer to Franklin Electric AIM data for motor cooling requirements.
MD
PAGE: SP-265
Model 225ST8 Performance DATE: Sept 1, 2007
Trim A
120 30.0
Trim B
68%
110 71% 27.5
73%
74%
100 25.0
90 Trim C 75%
74% 22.5
TOTAL DYNAMIC HEAD -FEET
73%
80 20.0
72%
70%
POWER (hp)
70 17.5
60 15.0
50 12.5
40 10.0
Trim A
30 Trim B 7.5
Trim C
20 5.0
10 2.5
0 0.0
0 40 80 120 160 200 240 280 320 360
FLOWRATE - U.S. GALLONS PER MINUTE
Note: Efficiencies are typical, not guaranteed. Efficiency derate for low stage count pumps- 1 stage-2%, 2 stage-1%
Pumps are intentionally designed to utilize some portion of the motors 1.15 service factor.
Bowl #13 begins transition to double-bolted (8 bolts @ bottom, 16 bolts @ top)
D
E
Impeller Dimensions
F Trim D Diameter E Diameter F Angle
A 5.705 5.400 20 o
B 5.561 5.250 20 o
C 5.083 4.750 20 o
Materials of Construction
Part Name Common Material Name Material Spec Number
Discharge Bracket Ductile Iron A536 65-45-12
Top Bowl Ductile Iron A536 65-45-12
Intermediate Bowl Ductile Iron A536 65-45-12
Bearings, Disch. & Suction Bronze B505 C932
Impeller Stainless Steel A743 CF-8
Pump Shaft Stainless Steel A582 416
Suction Bracket Ductile Iron A536 65-45-12
Bowl Bearing Rubber Nitrile
Sand Collar Stainless Steel A276
Suction Screen Stainless Steel A666
Cable Guard Stainless Steel A666
Shaft Coupling Stainless Steel A276
Upthrust Bolt Stainless Steel A320 304
Taper Lock Stainless Steel A276
Bolting Stainless Steel A320 304
PAGE: SP-270
Model 275ST8 Performance DATE: Sept 1, 2007
50 hp
600 75%
550 70%
500 40 hp 65%
450 60%
TOTAL DYNAMIC HEAD -FEET
400 55%
30 hp
EFFICIENCY %
350 50%
300 45%
250 20 hp 40%
200 35%
150 30%
10 hp
100 25%
50 20%
0 15%
0 50 100 150 200 250 300 350 400
FLOWRATE - U.S. GALLONS PER MINUTE
Specifications
Minimum Well I.D. 8”
Minimum Submergence @ BEP (above inlet) 10 Feet
Discharge 4” or 6” NPT
MD Note: Refer to Franklin Electric AIM data for motor cooling requirements.
Submersible Turbine Pumps
1500 70%
1400 65%
1200 55%
EFFICIENCY %
1100 50%
1000 45%
75 hp
900 40%
800 35%
60 hp
700 30%
600 25%
500 20%
0 50 100 150 200 250 300 350 400
FLOWRATE - U.S. GALLONS PER MINUTE
7.6
Dimension Information
Motor Disch. P M* MD* Motor Wt Pump Wt
HP Stages Trim
Size Size Inches Inches Inches Lbs. Lbs.
4” 53 61 5.38 334 312
60 6 A 6”
6” 53 61 5.38 334 321
P
4” 65 47 7.70 430 405
75 8 B 8”
6” 65 47 7.70 430 413
4” 76 55 7.70 530 475
100 10 B 8”
6” 76 55 7.70 530 483
4” 99 69 7.70 700 616
125 14 B 8”
6” 99 69 7.70 700 625
Note: *MD diameter = Franklin Electric Motor, M = Maximum Length of Franklin Electric Motor
M Specifications
Minimum Well I.D. 8”
Minimum Submergence @ BEP (above inlet) 10 Feet
Discharge 4” or 6” NPT
Note: Refer to Franklin Electric AIM data for motor cooling requirements.
MD
PAGE: SP-275
Model 275ST8 Performance DATE: Sept 1, 2007
74%
100 25.0
75%
Trim C 72%
90 22.5
70%
TOTAL DYNAMIC HEAD -FEET
69%
80 20.0
POWER (hp)
70 17.5
60 15.0
50 Trim A 12.5
40 Trim B 10.0
30 7.5
Trim C
20 5.0
10 2.5
0 0.0
0 50 100 150 200 250 300 350 400 450
FLOWRATE - U.S. GALLONS PER MINUTE
Note: Efficiencies are typical, not guaranteed. Efficiency derate for low stage count pumps- 1 stage-2%, 2 stage-1%
Pumps are intentionally designed to utilize some portion of the motors 1.15 service factor.
Bowl #13 begins transition to double-bolted (8 bolts @ bottom, 16 bolts @ top)
D
E
Impeller Dimensions
F Trim D Diameter E Diameter F Angle
A 5.705 5.400 20 o
B 5.562 5.250 20 o
C 5.084 4.750 20 o
Materials of Construction
Part Name Common Material Name Material Spec Number
Discharge Bracket Ductile Iron A536 65-45-12
Top Bowl Ductile Iron A536 65-45-12
Intermediate Bowl Ductile Iron A536 65-45-12
Bearings, Disch. & Suction Bronze B505 C932
Impeller Stainless Steel A743 CF-8
Pump Shaft Stainless Steel A582 416
Suction Bracket Ductile Iron A536 65-45-12
Bowl Bearing Rubber Nitrile
Sand Collar Stainless Steel A276
Suction Screen Stainless Steel A666
Cable Guard Stainless Steel A666
Shaft Coupling Stainless Steel A276
Upthrust Bolt Stainless Steel A320 304
Taper Lock Stainless Steel A276
Bolting Stainless Steel A320 304
PAGE: SP-280
Model 350ST8 Performance DATE: Sept 1, 2007
375 30 hp 75%
350 70%
325 65%
20 hp
300 60%
275 55%
TOTAL DYNAMIC HEAD -FEET
250 50%
EFFICIENCY %
225 45%
15 hp
200 40%
175 35%
150 30%
10 hp
125 25%
7.5 hp
100 20%
75 15%
50 10%
25 5%
0 0%
0 50 100 150 200 250 300 350 400 450 500
7.6
Dimension Information
Motor Disch. P M* MD* Motor Wt Pump Wt
HP Stages Trim
Size Size Inches Inches Inches Lbs. Lbs.
4” 26 24 5.38 110 130
7.5 1 B 6”
6” 26 24 5.38 110 138
P
4” 26 25 5.38 118 130
10 1 A 6”
6” 26 25 5.38 118 138
4” 33 28 5.38 131 161
15 2 B 6”
6” 33 28 5.38 131 170
4” 39 31 5.38 147 193
20 3 B 6”
6” 39 31 5.38 147 202
4” 39 36 5.38 176 193
30 3 A 6”
6” 39 36 5.38 176 202
Note: *MD diameter = Franklin Electric Motor, M = Maximum Length of Franklin Electric Motor
Specifications
Minimum Well I.D. 8”
Minimum Submergence @ BEP (above inlet) 10 Feet
Discharge 4” or 6” NPT
MD Note: Refer to Franklin Electric AIM data for motor cooling requirements.
Submersible Turbine Pumps
1500 70%
1300 60%
1200 55%
TOTAL DYNAMIC HEAD -FEET
75 hp
1100 50%
EFFICIENCY %
1000 45%
60 hp
900 40%
800 35%
50 hp
700 30%
40 hp
600 25%
500 20%
400 15%
300 10%
200 5%
0 50 100 150 200 250 300 350 400 450 500
FLOWRATE - U.S. GALLONS PER MINUTE
Dimension Information
7.6 Motor Disch. P M* MD* Motor Wt Pump Wt
HP Stages Trim
Size Size Inches Inches Inches Lbs. Lbs.
4” 58 41 5.38 206 289
40 6 B 6”
6” 58 41 5.38 206 298
4” 65 55 5.38 304 321
50 7 B 6”
6” 65 55 5.38 304 329
P
4” 77 61 5.38 334 385
60 9 B 6”
6” 77 61 5.38 334 393
4” 92 47 7.70 430 471
75 11 B 8”
6” 92 47 7.70 430 479
4” 92 55 7.70 530 471
100 11 A 8”
6” 92 55 7.70 530 479
4” 104 69 7.70 700 534
125 13 A 8”
6” 104 69 7.70 700 543
Note: *MD diameter = Franklin Electric Motor, M = Maximum Length of Franklin Electric Motor
M Specifications
Minimum Well I.D. 8”
Minimum Submergence @ BEP (above inlet) 10 Feet
Discharge 4” or 6” NPT
Note: Refer to Franklin Electric AIM data for motor cooling requirements.
MD
PAGE: SP-285
Model 350ST8 Performance DATE: Sept 1, 2007
130 65.0
Trim A
Trim B 78%
100 50.0
TOTAL DYNAMIC HEAD -FEET
90 45.0
77%
80 Trim C 40.0
POWER (hp)
74%
70 72% 35.0
60 75% 30.0
50 76% 25.0
40 20.0
30 15.0
Trim A
20 10.0
Trim B
10 Trim C 5.0
0 0.0
0 50 100 150 200 250 300 350 400 450 500
FLOWRATE - U.S. GALLONS PER MINUTE
D
E
Impeller Dimensions
F Trim D Diameter E Diameter F Angle
A 5.701 5.250 20 o
B 5.229 4.750 20 o
C 4.757 4.250 20 o
Materials of Construction
Part Name Common Material Name Material Spec Number
Discharge Bracket Ductile Iron A536 65-45-12
Top Bowl Ductile Iron A536 65-45-12
Intermediate Bowl Ductile Iron A536 65-45-12
Bearings, Disch. & Suction Bronze B505 C932
Impeller Stainless Steel A743 CF-8
Pump Shaft Stainless Steel A582 416
Suction Bracket Ductile Iron A536 65-45-12
Bowl Bearing Rubber Nitrile
Sand Collar Stainless Steel A276
Suction Screen Stainless Steel A666
Cable Guard Stainless Steel A666
Shaft Coupling Stainless Steel A276
Upthrust Bolt Stainless Steel A320 304
Taper Lock Stainless Steel A276
Bolting Stainless Steel A320 304
PAGE: SP-290
Model 450ST8 Performance DATE: Sept 1, 2007
50 hp
400 70%
350 60%
40 hp
300 50%
TOTAL DYNAMIC HEAD -FEET
EFFICIENCY %
250 40%
25 hp
200 30%
150 20 hp 20%
15 hp
100 10%
50 0%
0 -10%
0 100 200 300 400 500 600
FLOWRATE - U.S. GALLONS PER MINUTE
7.6
Dimension Information
Motor Disch. P M* MD* Motor Wt Pump Wt
HP Stages Trim
Size Size Inches Inches Inches Lbs. Lbs.
4” 26 28 5.38 131 130
15 1 B 6”
6” 26 28 5.38 131 138
P
4” 26 31 5.38 147 130
20 1 A 6”
6” 26 31 5.38 147 138
4” 33 33 5.38 156 161
25 2 B 6”
6” 33 33 5.38 156 170
4” 39 41 5.38 206 193
40 3 B 6”
6” 39 41 5.38 206 202
4” 39 55 5.38 304 193
50 3 A 6”
6” 39 55 5.38 304 202
Note: *MD diameter = Franklin Electric Motor, M = Maximum Length of Franklin Electric Motor
Specifications
Minimum Well I.D. 8”
Minimum Submergence @ BEP (above inlet) 10 Feet
Discharge 4” or 6” NPT
MD Note: Refer to Franklin Electric AIM data for motor cooling requirements.
Submersible Turbine Pumps
125 hp
1000 70%
900 60%
100 hp
800 50%
TOTAL DYNAMIC HEAD -FEET
EFFICIENCY %
700 40%
75 hp
600 30%
60 hp
500 20%
400 10%
300 0%
200 -10%
0 100 200 300 400 500 600
FLOWRATE - U.S. GALLONS PER MINUTE
7.6
Dimension Information
Motor Disch. P M* MD* Motor Wt Pump Wt
HP Stages Trim
Size Size Inches Inches Inches Lbs. Lbs.
4” 52 61 5.38 334 257
60 5 B 6”
6” 52 61 5.38 334 266
P 4” 60 47 7.7 430 311
75 6 B 8”
6” 60 47 7.7 430 320
4” 72 55 7.7 530 375
100 8 B 8”
6” 72 55 7.7 530 384
4” 85 69 7.7 700 439
125 10 B 8”
6” 85 69 7.7 700 447
Note: *MD diameter = Franklin Electric Motor, M = Maximum Length of Franklin Electric Motor
Specifications
Minimum Well I.D. 8”
M Minimum Submergence @ BEP (above inlet) 10 Feet
Discharge 4” or 6” NPT
Note: Refer to Franklin Electric AIM data for motor cooling requirements.
MD
PAGE: SP-295
Model 450ST8 Performance DATE: Sept 1, 2007
90 45.0
Trim C
80 40.0
POWER (hp)
70 35.0
60 30.0
70%
50 25.0
40 Trim A 20.0
30 Trim B 15.0
Trim C
20 10.0
10 5.0
0 0.0
0 100 200 300 400 500 600
FLOWRATE - U.S. GALLONS PER MINUTE
D
E
Impeller Dimensions
F Trim D Diameter E Diameter F Angle
A 5.720 5.287 20 o
B 5.302 4.842 20 o
C 4.835 4.349 20 o
Materials of Construction
Part Name Common Material Name Material Spec Number
Discharge Bracket Ductile Iron A536 65-45-12
Top Bowl Ductile Iron A536 65-45-12
Intermediate Bowl Ductile Iron A536 65-45-12
Bearings, Disch. & Suction Bronze B505 C932
Impeller Stainless Steel A743 CF-8
Pump Shaft Stainless Steel A582 416
Suction Bracket Ductile Iron A536 65-45-12
Bowl Bearing Rubber Nitrile
Sand Collar Stainless Steel A276
Suction Screen Stainless Steel A666
Cable Guard Stainless Steel A666
Shaft Coupling Stainless Steel A276
Upthrust Bolt Stainless Steel A320 304
Taper Lock Stainless Steel A276
Bolting Stainless Steel A320 304
PAGE: SP-300
Model 550ST8 Performance DATE: Sept 1, 2007
50 hp
450 70%
40 hp
400 60%
350 50%
TOTAL DYNAMIC HEAD -FEET
30 hp
300 40%
EFFICIENCY %
250 30%
20 hp
200 20%
150 10%
10 hp
100 0%
50 -10%
0 -20%
0 100 200 300 400 500 600 700 800
FLOWRATE - U.S. GALLONS PER MINUTE
7.6
Dimension Information
Motor Disch. P M* MD* Motor Wt Pump Wt
HP Stages Trim
Size Size Inches Inches Inches Lbs. Lbs.
4” 27 25 5.38 118 137
10 1 B 6”
6” 27 25 5.38 118 146
P
4” 34 31 5.38 147 172
20 2 B 6”
6” 34 31 5.38 147 181
4” 41 36 5.38 176 208
30 3 B 6”
6” 41 36 5.38 176 217
4” 48 41 5.38 206 243
40 4 B 6”
6” 48 41 5.38 206 252
4” 48 55 5.38 304 243
50 4 A 6”
6” 48 55 5.38 304 252
Note: *MD diameter = Franklin Electric Motor, M = Maximum Length of Franklin Electric Motor
Specifications
Minimum Well I.D. 8”
Minimum Submergence @ BEP (above inlet) 10 Feet
Discharge 4” or 6” NPT
MD Note: Refer to Franklin Electric AIM data for motor cooling requirements.
Submersible Turbine Pumps
1100 60%
1000 50%
100 hp
TOTAL DYNAMIC HEAD -FEET
900 40%
EFFICIENCY %
800 30%
75 hp
700 20%
60 hp
600 10%
500 0%
400 -10%
300 -20%
200 -30%
0 100 200 300 400 500 600 700 800
FLOWRATE - U.S. GALLONS PER MINUTE
7.6
Dimension Information
Motor Disch. P M* MD* Motor Wt Pump Wt
HP Stages Trim
Size Size Inches Inches Inches Lbs. Lbs.
4” 63 61 5.38 334 314
60 6 B 6”
6” 63 61 5.38 334 323
P 4” 64 47 7.70 430 337
75 6 A 8”
6” 64 47 7.70 430 345
4” 78 55 7.70 530 408
100 8 B 8”
6” 78 55 7.70 530 416
4” 92 69 7.70 700 479
125 10 B 8”
6” 92 69 7.70 700 487
Note: *MD diameter = Franklin Electric Motor, M = Maximum Length of Franklin Electric Motor
Specifications
Minimum Well I.D. 8”
M
Minimum Submergence @ BEP (above inlet) 10 Feet
Discharge 4” or 6” NPT
Note: Refer to Franklin Electric AIM data for motor cooling requirements.
MD
PAGE: SP-305
Model 550ST8 Performance DATE: Sept 1, 2007
100 50.0
Trim B
75%
70 73% 35.0
76%
POWER (hp)
71%
60 30.0
68%
50 25.0
40 20.0
30 15.0
Trim A
20 Trim B 10.0
Trim C
10 5.0
0 0.0
0 100 200 300 400 500 600 700 800
FLOWRATE - U.S. GALLONS PER MINUTE
Note: Efficiencies are typical, not guaranteed. Efficiency derate for low stage count pumps- 1 stage-3%, 2 stage-2%, 3 stage-3%
Pumps are intentionally designed to utilize some portion of the motors 1.15 service factor.
Bowl #13 begins transition to double-bolted (8 bolts @ bottom, 16 bolts @ top)
D
E
Impeller Dimensions
F Trim D Diameter E Diameter F Angle
A 5.674 5.000 17 o
B 5.371 4.661 17 o
C 5.227 4.500 17 o
Materials of Construction
Part Name Common Material Name Material Spec Number
Discharge Bracket Ductile Iron A536 65-45-12
Top Bowl Ductile Iron A536 65-45-12
Intermediate Bowl Ductile Iron A536 65-45-12
Bearings, Disch. & Suction Bronze B505 C932
Impeller Stainless Steel A743 CF-8
Pump Shaft Stainless Steel A582 416
Suction Bracket Ductile Iron A536 65-45-12
Bowl Bearing Rubber Nitrile
Sand Collar Stainless Steel A276
Suction Screen Stainless Steel A666
Cable Guard Stainless Steel A666
Shaft Coupling Stainless Steel A276
Upthrust Bolt Stainless Steel A320 304
Taper Lock Stainless Steel A276
Bolting Stainless Steel A320 304
PAGE: SP-310
Model 700ST8 Performance DATE: Sept 1, 2007
650 70%
550 60%
500 55%
TOTAL DYNAMIC HEAD -FEET
450 50%
EFFICIENCY %
75 hp
400 45%
350 40%
60 hp
300 35%
50 hp
250 30%
200 40 hp 25%
150 20%
100 20 hp 15%
50 10%
0 5%
0 100 200 300 400 500 600 700 800 900
FLOWRATE - U.S. GALLONS PER MINUTE
Dimension Information
7.6
Motor Disch. P M* MD* Motor Wt Pump Wt
HP Stages Trim
Size Size Inches Inches Inches Lbs. Lbs.
4” 27 31 5.38 147 137
20 1 A 6”
6” 27 31 5.38 147 146
4” 34 41 5.38 206 172
40 2 A 6”
6” 34 41 5.38 206 181
P
4” 41 55 5.38 176 208
50 3 B 6”
6” 41 55 5.38 176 217
4” 41 61 5.38 334 208
60 3 A 6”
6” 41 61 5.38 334 217
4” 50 47 7.70 430 266
75 4 B 8”
6” 50 47 7.70 430 274
4” 64 55 7.70 530 337
100 6 B 8”
6” 64 55 7.70 530 345
4” 71 69 7.70 700 372
125 7 B 8”
6” 71 69 7.70 700 381
M Note: *MD diameter = Franklin Electric Motor, M = Maximum Length of Franklin Electric Motor
Specifications
Minimum Well I.D. 8”
Minimum Submergence @ BEP (above inlet) 10 Feet
MD Discharge 4” or 6” NPT
Note: Refer to Franklin Electric AIM data for motor cooling requirements.
Submersible Turbine Pumps
Trim A
110 55.0
74%
80 73% 40.0
TOTAL DYNAMIC HEAD -FEET
71%
76%
70 75% 35.0
POWER (hp)
75%
60 30.0
50 25.0
Trim A
40 20.0
Trim B
30 Trim C 15.0
20 10.0
10 5.0
0 0.0
0 100 200 300 400 500 600 700 800 900 1000
FLOWRATE - U.S. GALLONS PER MINUTE
Note: Efficiencies are typical, not guaranteed. Efficiency derate for low stage count pumps- 1 stage-3%, 2 stage-2%, 3 stage-1%
Pumps are intentionally designed to utilize some portion of the motors 1.15 service factor.
Bowl #13 begins transition to double-bolted (8 bolts @ bottom, 16 bolts @ top)
D
E
Impeller Dimensions
F Trim D Diameter E Diameter F Angle
A 5.672 4.980 17 o
B 5.451 4.742 17 o
C 5.225 4.500 17 o
Materials of Construction
Part Name Common Material Name Material Spec Number
Discharge Bracket Ductile Iron A536 65-45-12
Top Bowl Ductile Iron A536 65-45-12
Intermediate Bowl Ductile Iron A536 65-45-12
Bearings, Disch. & Suction Bronze B505 C932
Impeller Stainless Steel A743 CF-8
Pump Shaft Stainless Steel A582 416
Suction Bracket Ductile Iron A536 65-45-12
Bowl Bearing Rubber Nitrile
Sand Collar Stainless Steel A276
Suction Screen Stainless Steel A666
Cable Guard Stainless Steel A666
Shaft Coupling Stainless Steel A276
Upthrust Bolt Stainless Steel A320 304
Taper Lock Stainless Steel A276
Bolting Stainless Steel A320 304
PAGE: SP-315
Model 1000ST8 Performance DATE: Mar 1, 2009
Meters
Feet
75
Efficiency (%)
425 70
75 hp
400 65
120
375 60
3450 rpm
350 3525 rpm 55
100 60 hp
325
300
275
80
250
50 hp
225
40 hp
60 200
175
150
40
125
30 hp
100
25 hp
75
20
5 FT
50
20 GPM
25
0 0
0 100 200 300 400 500 600 700 800 9 0 0 1 0 0 0 1 1 0 0 1 2 0 0 1 3 0 0 US GPM
0 20 40 60 80 100 120 140 160 180 200 220 240 260 280 M3PH
Dimension Information
8.00
Motor P M* MD* Motor Wt Pump Wt
HP Stages Trim
Size Inches Inches Inches Lbs. Lbs.
25 1 B 6” 28.63 33 5.38 156 94
30 1 A 6” 28.63 36 5.38 174 94
P
2 B 6” 36.00 41 5.38 206 123
40 2 B 8” 37.38 36 7.70 320 143
2 A 6” 36.00 55 5.38 300 123
50 2 A 8” 37.38 39 7.70 345 143
3 1A 2B 6” 43.38 61 5.38 330 151
60 3 1A 2B 8” 44.76 42 7.70 375 172
75 4 B 8” 52.13 47 7.70 430 200
Note: *MD diameter = Franklin Electric Motor, M = Maximum Length of Franklin Electric Motor
M
Specifications
Minimum Well I.D. 10”
Bowl Diameter (without cable guard) 7.75”
Minimum Submergence Above Inlet 50 Feet
Discharge 6” NPT MD
Maximum Working Pressure Standard: 350 psi
Note: Refer to Franklin Electric AIM data for motor cooling requirements.
Materials of Construction
Part Name Common Material Name Material Spec Number
Discharge Bracket Ductile Iron A536 65-45-12
Top Bowl Ductile Iron A536 65-45-12
Intermediate Bowl Ductile Iron A536 65-45-12
Bearings, Disch. & Suction Bronze B505 C932
Impeller Stainless Steel A743 CF-8
Pump Shaft Stainless Steel A582 416
Suction Bracket Ductile Iron A536 65-45-12
Bowl Bearing Rubber Nitrile
Sand Collar Stainless Steel A276
Suction Screen Stainless Steel A666
Cable Guard Stainless Steel A666
Shaft Coupling Stainless Steel A276
Upthrust Bolt Stainless Steel A320 304
Taper Lock Stainless Steel A276
Bolting Stainless Steel A320 304
PAGE: SP-320
Model 1000ST8 Performance DATE: Mar 1, 2009
Meters
Feet
75
350
200 hp
1100 70
Efficiency (%)
1000
175 hp 65
300
900 60
150 hp
3525 rpm
250
800 55
125 hp
700
200
600
100 hp
150 500
400
100
20 FT
300
20 GPM
200
50
100
0 100 200 300 400 500 600 700 800 9 0 0 1 0 0 0 1 1 0 0 1 2 0 0 1 3 0 0 US GPM
0 20 40 60 80 100 120 140 160 180 200 220 240 260 280 M3PH
Dimension Information
8.00
Motor P M* MD* Motor Wt Pump Wt
HP Stages Trim
Size Inches Inches Inches Lbs. Lbs.
100 4 A 8” 52.13 55 7.70 530 200
125 6 5A 1B 8” 66.89 69 7.70 700 258
P
150 7 A 8” 74.26 78 7.70 840 286
175 8 A 8” 81.64 86 7.70 925 315
200 9 A 8” 89.02 95 7.70 1040 343
Note: *MD diameter = Franklin Electric Motor, M = Maximum Length of Franklin Electric Motor
Specifications
Minimum Well I.D. 10”
M
Bowl Diameter (without cable guard) 7.75”
Minimum Submergence Above Inlet 50 Feet
Discharge 6” NPT
Maximum Working Pressure Standard: 350 psi
Note: Refer to Franklin Electric AIM data for motor cooling requirements. MD
Materials of Construction
Part Name Common Material Name Material Spec Number
Discharge Bracket Ductile Iron A536 65-45-12
Top Bowl Ductile Iron A536 65-45-12
Intermediate Bowl Ductile Iron A536 65-45-12
Bearings, Disch. & Suction Bronze B505 C932
Impeller Stainless Steel A743 CF-8
Pump Shaft Stainless Steel A582 416
Suction Bracket Ductile Iron A536 65-45-12
Bowl Bearing Rubber Nitrile
Sand Collar Stainless Steel A276
Suction Screen Stainless Steel A666
Cable Guard Stainless Steel A666
Shaft Coupling Stainless Steel A276
Upthrust Bolt Stainless Steel A320 304
Taper Lock Stainless Steel A276
Bolting Stainless Steel A320 304
PAGE: SP-325
Model 1000ST8 Performance DATE: Mar 1, 2009
Feet
90
25
80
Trim A
2 FT
20
20 GPM
60 72% 70%
74%
72% 68%
50 66%
15
40
10
30
Power (kW)
Power (hp)
20
5
10
0 0 28.0
20
Trim A 18
24.0
-5 Trim B 16
20.0
14
16.0 12
600 700 800 900 1000 1100 1200 US GPM
Note: Efficiencies are typical, not guaranteed. Efficiency derate for low stage count pumps: 1 stage-4%, 2 stage-2%
Pumps are intentionally designed to utilize some portion of the motor's 1.15 service factor.
Nominal RPM: 3525
D Impeller Dimensions
E
F Trim D Diameter E Diameter F Angle
A 5.716 5.039 11 o
B 5.716 4.377 21 o
Features:
■ Stainless steel impellers and diffusers to resist corrosion.
■ Heavy duty stainless steel shell assures permanent alignment of
all components to increase longevity and enables higher pressures
than strap designs.
■ Teflon® floating wear ring, ceramic bearing journal and Nitrile
rubber fluted bearing ensure durability against wear for long-lasting
performance and reliability.
■ Suited to operate in horizontal position.
■ Built-in check valve to protect the pump against water hammer.
Model Number Explanation ■ Energy efficient hydraulic design for cost effective operation.
Example: 150SR10F6A-0443 ■ Space-saving compact design.
150 = Gallons per Minute
■ Easy to install and dismantle for service in the field if necessary.
SR = Series
10 = Horsepower
F = Stainless
6 = 6” Pump
A = Impeller Trim
04 = Number of Stages
4 = 4” Motor
3 = 3” Discharge
Submersible Pumps
FEET
800
70
EFFICIENCY %
60
200
15 hp
600
50
15 hp
150
40
10 hp
400
10 hp
100
7.5 hp
200
50 5 hp
0 0
0 20 40 60 80 100 120 140 GPM
M3PH
0 5 10 15 20 25 30 35
Submersible Pumps
Dimension Information
Diameter Pump Weight
HP Stages D* Motor Size P*
w/Cable Guard Lbs.
5 3 3” 4” 5.55” 12.5” 20
7.5 5 3” 4” 5.55” 15.5” 24
10 6 3” 4” 5.55” 17.0” 27
P
10 7 3” 4” 5.55” 18.4” 28
15 9 3” 6” 5.67” 21.4” 31
15 11 3” 6” 5.67” 24.4” 35
*Note: D = Discharge, P = Pump Length
Material
Parts Description
Type AISI
Outer case with motor adapter Stainless Steel 304
Discharge head with built-in check valve Stainless Steel 304
Sealing O-ring Nitrile Rubber (NBR) N/A
Upper bowl Stainless Steel 304
Upper bearing bushing Nitrile Rubber (NBR) N/A
Stainless Steel
Upper journal sleeve w/ ceramic coating 329
Pump shaft Stainless Steel 431
Motor coupling Stainless Steel 431/329
Diffuser Stainless Steel 304
Floating neck ring Teflon (PTFE) N/A
Secondary bearing bushing Nitrile Rubber (NBR) N/A
Secondary journal sleeve Stainless Steel 304
Impeller Stainless Steel 304
Cable guard Stainless Steel 316
Suction strainer Stainless Steel 316
Insert locking outer case Stainless Steel 316
Up-thrust washer Stainless Steel 316
Up-thrust disc Teflon (PTFE) N/A
Screws and washers Stainless Steel 316
FEET
1600
70
EFFICIENCY %
40 hp
450
60
1400 40 hp
50
400
30 hp
40
1200
350
25 hp
300 1000
20 hp
250
800
20 hp
200
600
150
400
100
200
50
0 0
0 20 40 60 80 100 120 140 GPM
0 5 10 15 20 25 30 35 M3PH
Submersible Pumps
Dimension Information
Diameter Pump Weight
HP Stages D* Motor Size P*
w/Cable Guard Lbs.
20 13 3” 6” 5.67” 27.3” 39
20 15 3” 6” 5.67” 30.3” 42
25 18 3” 6” 5.67” 35.2” 47 P
30 22 3” 6” 5.67” 40.6” 55
40 26 3” 6” 5.67” 46.5” 62
40 28 3” 6” 5.67” 49.4” 66
*Note: D = Discharge, P = Pump Length
Material
Parts Description
Type AISI
Outer case with motor adapter Stainless Steel 304
Discharge head with built-in check valve Stainless Steel 304
Sealing O-ring Nitrile Rubber (NBR) N/A
Upper bowl Stainless Steel 304
Upper bearing bushing Nitrile Rubber (NBR) N/A
Stainless Steel
Upper journal sleeve w/ ceramic coating 329
Pump shaft Stainless Steel 431
Motor coupling Stainless Steel 431/329
Diffuser Stainless Steel 304
Floating neck ring Teflon (PTFE) N/A
Secondary bearing bushing Nitrile Rubber (NBR) N/A
Secondary journal sleeve Stainless Steel 304
Impeller Stainless Steel 304
Cable guard Stainless Steel 316
Suction strainer Stainless Steel 316
Insert locking outer case Stainless Steel 316
Up-thrust washer Stainless Steel 316
Up-thrust disc Teflon (PTFE) N/A
Screws and washers Stainless Steel 316
FEET
800 80
EFFICIENCY %
70
200
60
600
20 hp 50
150
15 hp
400
100
15 hp
10 hp
200
7.5 hp
50
0 0
0 40 80 120 160 200 GPM
0 10 20 30 40 50 M3PH
Submersible Pumps
Dimension Information
Diameter Pump Weight
HP Stages D* Motor Size P*
w/Cable Guard Lbs.
7.5 3 3” 4” 5.55” 14.4” 23
10 4 3” 4” 5.55” 16.2” 25
15 5 3” 6” 5.67” 18.0” 28 P
15 7 3” 6” 5.67” 21.7” 32
20 9 3” 6” 5.67” 25.3” 36
Material
Parts Description
Type AISI
Outer case with motor adapter Stainless Steel 304
Discharge head with built-in check valve Stainless Steel 304
Sealing O-ring Nitrile Rubber (NBR) N/A
Upper bowl Stainless Steel 304
Upper bearing bushing Nitrile Rubber (NBR) N/A
Stainless Steel
Upper journal sleeve w/ ceramic coating 329
Pump shaft Stainless Steel 431
Motor coupling Stainless Steel 431/329
Diffuser Stainless Steel 304
Floating neck ring Teflon (PTFE) N/A
Secondary bearing bushing Nitrile Rubber (NBR) N/A
Secondary journal sleeve Stainless Steel 304
Impeller Stainless Steel 304
Cable guard Stainless Steel 316
Suction strainer Stainless Steel 316
Insert locking outer case Stainless Steel 316
Up-thrust washer Stainless Steel 316
Up-thrust disc Teflon (PTFE) N/A
Screws and washers Stainless Steel 316
FEET
1400 80
50 hp
EFFICIENCY %
400 70
60
1200
350
40 hp 50
40
300 1000
40 hp
250
800
30 hp
200 25 hp
600
150
400
100
200
50
0 0
0 40 80 120 160 200 GPM
0 10 20 30 40 50 M3PH
Submersible Pumps
Dimension Information
Diameter Pump Weight
HP Stages D* Motor Size P*
w/Cable Guard Lbs.
25 11 3” 6” 5.67” 29.0” 41
30 14 3” 6” 5.67” 34.5” 47
40 15 3” 6” 5.67” 36.8” 49 P
40 19 3” 6” 5.67” 43.7” 57
50 23 3” 6” 5.67” 51.0” 66
*Note: D = Discharge, P = Pump Length
Material
Parts Description
Type AISI
Outer case with motor adapter Stainless Steel 304
Discharge head with built-in check valve Stainless Steel 304
Sealing O-ring Nitrile Rubber (NBR) N/A
Upper bowl Stainless Steel 304
Upper bearing bushing Nitrile Rubber (NBR) N/A
Stainless Steel
Upper journal sleeve w/ ceramic coating 329
Pump shaft Stainless Steel 431
Motor coupling Stainless Steel 431/329
Diffuser Stainless Steel 304
Floating neck ring Teflon (PTFE) N/A
Secondary bearing bushing Nitrile Rubber (NBR) N/A
Secondary journal sleeve Stainless Steel 304
Impeller Stainless Steel 304
Cable guard Stainless Steel 316
Suction strainer Stainless Steel 316
Insert locking outer case Stainless Steel 316
Up-thrust washer Stainless Steel 316
Up-thrust disc Teflon (PTFE) N/A
Screws and washers Stainless Steel 316
FEET
600 80
70
EFFICIENCY %
150
60
20 hp
400 50
20 hp
100 40
15 hp
10 hp
200
50
7.5 hp
0 0
0 40 80 120 160 200 240 280 GPM
0 10 20 30 40 50 60 70 M3PH
Submersible Pumps
Dimension Information
Diameter Pump Weight
HP Stages D* Motor Size P*
w/Cable Guard Lbs.
7.5 2 3” 4” 5.55” 14.4” 24
10 3 3” 4” 5.55” 18.1” 30
15 4 3” 6” 5.67” 21.7” 35 P
20 5 3” 6” 5.67” 25.3” 40
20 6 3” 6” 5.67” 29.0” 45
*Note: D = Discharge, P = Pump Length
Material
Parts Description
Type AISI
Outer case with motor adapter Stainless Steel 304
Discharge head with built-in check valve Stainless Steel 304
Sealing O-ring Nitrile Rubber (NBR) N/A
Upper bowl Stainless Steel 304
Upper bearing bushing Nitrile Rubber (NBR) N/A
Stainless Steel
Upper journal sleeve w/ ceramic coating 329
Pump shaft Stainless Steel 431
Motor coupling Stainless Steel 431/329
Diffuser Stainless Steel 304
Floating neck ring Teflon (PTFE) N/A
Secondary bearing bushing Nitrile Rubber (NBR) N/A
Secondary journal sleeve Stainless Steel 304
Impeller Stainless Steel 304
Cable guard Stainless Steel 316
Suction strainer Stainless Steel 316
Insert locking outer case Stainless Steel 316
Up-thrust washer Stainless Steel 316
Up-thrust disc Teflon (PTFE) N/A
Screws and washers Stainless Steel 316
FEET
350 80
EFFICIENCY %
70
50 hp
1000
300
60
50
250 40 hp
800
40
40 hp
200
30 hp
600
150 25 hp
400
100
200
50
0 0
0 40 80 120 160 200 240 280 GPM
0 10 20 30 40 50 60 70 M3PH
Submersible Pumps
Dimension Information
Diameter Pump Weight
HP Stages D* Motor Size P*
w/Cable Guard Lbs.
25 7 3” 6” 5.67” 32.6” 50
30 9 3” 6” 5.67” 39.9” 60
40 10 3” 6” 5.67” 43.6” 65 P
40 12 3” 6” 5.67” 50.9” 75
50 15 3” 6” 5.67” 61.9” 90
*Note: D = Discharge, P = Pump Length
Material
Parts Description
Type AISI
Outer case with motor adapter Stainless Steel 304
Discharge head with built-in check valve Stainless Steel 304
Sealing O-ring Nitrile Rubber (NBR) N/A
Upper bowl Stainless Steel 304
Upper bearing bushing Nitrile Rubber (NBR) N/A
Stainless Steel
Upper journal sleeve w/ ceramic coating 329
Pump shaft Stainless Steel 431
Motor coupling Stainless Steel 431/329
Diffuser Stainless Steel 304
Floating neck ring Teflon (PTFE) N/A
Secondary bearing bushing Nitrile Rubber (NBR) N/A
Secondary journal sleeve Stainless Steel 304
Impeller Stainless Steel 304
Cable guard Stainless Steel 316
Suction strainer Stainless Steel 316
Insert locking outer case Stainless Steel 316
Up-thrust washer Stainless Steel 316
Up-thrust disc Teflon (PTFE) N/A
Screws and washers Stainless Steel 316
FEET
600 80
70
EFFICIENCY %
500
150
25 hp 60
400 20 hp 50
100 20 hp
40
300
15 hp
200 10 hp
50
7.5 hp
100
0 0
0 40 80 120 160 200 240 280 320 GPM
0 10 20 30 40 50 60 70 80 M3PH
Submersible Pumps
Dimension Information
Diameter Pump Weight
HP Stages D* Motor Size P*
w/Cable Guard Lbs.
7.5 2 3” 4” 5.55” 14.4” 25
10 3 3” 4” 5.55” 18.0” 30
15 4 3” 6” 5.67” 21.7” 35
20 5 3” 6” 5.67” 25.3” 40 P
20 6 3” 6” 5.67” 29.0” 45
25 7 3” 6” 5.67” 32.6” 51
*Note: D = Discharge, P = Pump Length
Material
Parts Description
Type AISI
Outer case with motor adapter Stainless Steel 304
Discharge head with built-in check valve Stainless Steel 304
Sealing O-ring Nitrile Rubber (NBR) N/A
Upper bowl Stainless Steel 304
Upper bearing bushing Nitrile Rubber (NBR) N/A
Stainless Steel
Upper journal sleeve w/ ceramic coating 329
Pump shaft Stainless Steel 431
Motor coupling Stainless Steel 431/329
Diffuser Stainless Steel 304
Floating neck ring Teflon (PTFE) N/A
Secondary bearing bushing Nitrile Rubber (NBR) N/A
Secondary journal sleeve Stainless Steel 304
Impeller Stainless Steel 304
Cable guard Stainless Steel 316
Suction strainer Stainless Steel 316
Insert locking outer case Stainless Steel 316
Up-thrust washer Stainless Steel 316
Up-thrust disc Teflon (PTFE) N/A
Screws and washers Stainless Steel 316
FEET
1100 80
EFFICIENCY %
70
1000
300 50 hp
60
50 hp
900
50
250 40
800
40 hp
700
200 40 hp
600 30 hp
30 hp
150 500
400
100
300
200
50
100
0 0
0 40 80 120 160 200 240 280 320 GPM
0 10 20 30 40 50 60 70 80 M3PH
Submersible Pumps
Dimension Information
Diameter Pump Weight
HP Stages D* Motor Size P*
w/Cable Guard Lbs.
30 8 4” 6” 5.67” 36.3” 55
30 9 4” 6” 5.67” 39.9” 60
40 10 4” 6” 5.67” 43.6” 66 P
40 12 4” 6” 5.67” 50.9” 75
50 14 4” 6” 5.67” 58.2” 86
50 15 4” 6” 5.67” 61.9” 90
Material
Parts Description
Type AISI
Outer case with motor adapter Stainless Steel 304
Discharge head with built-in check valve Stainless Steel 304
Sealing O-ring Nitrile Rubber (NBR) N/A
Upper bowl Stainless Steel 304
Upper bearing bushing Nitrile Rubber (NBR) N/A
Stainless Steel
Upper journal sleeve w/ ceramic coating 329
Pump shaft Stainless Steel 431
Motor coupling Stainless Steel 431/329
Diffuser Stainless Steel 304
Floating neck ring Teflon (PTFE) N/A
Secondary bearing bushing Nitrile Rubber (NBR) N/A
Secondary journal sleeve Stainless Steel 304
Impeller Stainless Steel 304
Cable guard Stainless Steel 316
Suction strainer Stainless Steel 316
Insert locking outer case Stainless Steel 316
Up-thrust washer Stainless Steel 316
Up-thrust disc Teflon (PTFE) N/A
Screws and washers Stainless Steel 316
FEET
600 100
EFFICIENCY %
80
150
40 hp
60
400
40
30 hp
100
25 hp
200 15 hp
50
0 0
0 100 200 300 400 500 GPM
0 20 40 60 80 100 120 3
M PH
Submersible Pumps
Dimension Information
Diameter Pump Weight
HP Stages D* Motor Size P*
w/Cable Guard Lbs.
15 2 4” 6” 7.34” 25.3” 70
P
L
25 3 4” 6” 7.34” 30.3” 81
30 4 4” 6” 7.34” 35.2” 92
40 5 4” 6” 7.34” 40.2” 103
*Note: D = Discharge, P = Pump Length
Material
Parts Description
Type AISI
Outer case Stainless Steel 316
Motor adapter and flange Stainless Steel 316
Suction strainer Stainless Steel 316
Discharge head Stainless Steel 316
Check valve assembly Stainless Steel 316
Sealing O-ring Nitrile Rubber (NBR) N/A
Stop ring Stainless Steel 316
Spring Stainless Steel 316
Pump shaft Stainless Steel 329
Upper journal sleeve Silicon Carbide (SiC) N/A
Motor coupling Stainless Steel 316/329
Diffuser Stainless Steel 316
Floating neck ring Teflon (PTFE) N/A
Secondary bearing bushing Nitrile Rubber (NBR) N/A
Flange clamping neck ring Stainless Steel 316
Impeller Stainless Steel 316
Collet Stainless Steel 316
Collet nut Stainless Steel 316
Cable guard Stainless Steel 316
Insert locking outer case Stainless Steel 316
Up-thrust washer Stainless Steel 329
Up-thrust disc Teflon (PTFE) N/A
Screws and washers Stainless Steel 316
FEET
1400 100
400
100 hp
EFFICIENCY %
80
1200
350
60
1000 75 hp
300
40
250
800 60 hp
50 hp
200
600
150
400
100
200
50
0 0
0 100 200 300 400 500 GPM
Dimension Information
Diameter Pump Weight
HP Stages D* Motor Size P*
w/Cable Guard Lbs.
50 7 4” 6” 7.34” 50.1” 124
60 8 4” 8” 7.34” 55.0” 135
P
L
75 10 4” 8” 7.34” 65.1” 157
100 13 4” 8” 7.34” 80.0” 192
*Note: D = Discharge, P = Pump Length
Material
Parts Description
Type AISI
Outer case Stainless Steel 316
Motor adapter and flange Stainless Steel 316
Suction strainer Stainless Steel 316
Discharge head Stainless Steel 316
Check valve assembly Stainless Steel 316
Sealing O-ring Nitrile Rubber (NBR) N/A
Stop ring Stainless Steel 316
Spring Stainless Steel 316
Pump shaft Stainless Steel 329
Upper journal sleeve Silicon Carbide (SiC) N/A
Motor coupling Stainless Steel 316/329
Diffuser Stainless Steel 316
Floating neck ring Teflon (PTFE) N/A
Secondary bearing bushing Nitrile Rubber (NBR) N/A
Flange clamping neck ring Stainless Steel 316
Impeller Stainless Steel 316
Collet Stainless Steel 316
Collet nut Stainless Steel 316
Cable guard Stainless Steel 316
Insert locking outer case Stainless Steel 316
Up-thrust washer Stainless Steel 329
Up-thrust disc Teflon (PTFE) N/A
Screws and washers Stainless Steel 316
FEET
1400 100
EFFICIENCY %
400 125 hp
80
1200
350
60
100 hp
300 1000 40
75 hp
250
800
60 hp
200
50 hp
600
150
40 hp
400
100 30 hp
200
50
0 0
0 100 200 300 400 500 600 700 GPM
Dimension Information
Diameter Pump Weight
HP Stages D* Motor Size P*
w/Cable Guard Lbs.
30 3 6” 6” 7.34” 30.3” 81
40 4 6” 6” 7.34” 35.2” 92
50 6 6” 6” 7.34” 45.1” 112 P
L
60 7 6” 6” 7.34” 50.1” 124
75 8 6” 8” 7.68” 55.2” 138
100 10 6” 8” 7.68” 65.1” 159
125 13 6” 8” 7.68” 80.0” 192
*Note: D = Discharge, P = Pump Length
Material
Parts Description
Type AISI
Outer case Stainless Steel 316
Motor adapter and flange Stainless Steel 316
Suction strainer Stainless Steel 316
Discharge head Stainless Steel 316
Check valve assembly Stainless Steel 316
Sealing O-ring Nitrile Rubber (NBR) N/A
Stop ring Stainless Steel 316
Spring Stainless Steel 316
Pump shaft Stainless Steel 329
Upper journal sleeve Silicon Carbide (SiC) N/A
Motor coupling Stainless Steel 316/329
Diffuser Stainless Steel 316
Floating neck ring Teflon (PTFE) N/A
Secondary bearing bushing Nitrile Rubber (NBR) N/A
Flange clamping neck ring Stainless Steel 316
Impeller Stainless Steel 316
Collet Stainless Steel 316
Collet nut Stainless Steel 316
Cable guard Stainless Steel 316
Insert locking outer case Stainless Steel 316
Up-thrust washer Stainless Steel 329
Up-thrust disc Teflon (PTFE) N/A
Screws and washers Stainless Steel 316
Applications:
■ Boosting water pressure from either city mains or private
water systems.
■ Pressure washing buildings and floors.
■ Poultry houses.
■ Spray Cooling Equipment.
■ Lawn and Crop Irrigation.
■ Evaporating cooling system/misters.
■ Water Circulation.
■ General Purpose pumping.
■ Reverse Osmosis- Stainless Steel HB4
■ Filtration- Stainless Steel HB4
Ordering Information
Cast Iron Models Features:
CAST IRON MODELS
■ Custom O-Ring seal for reliable high pressure sealing.
Single Phase
GPM HP ■ Thermoplastic impellers and diffusers for increased
Model No. Order No. Wt.
efficiency.
5 1 1FHB4P5C15-S 91270515 48
1/2 5FHB4P8C9-S 91270809 37 ■ Open drip-proof motors.
8 3/4 7FHB4P8C11-S 91270811 42
■ Standard 5/8” type 21 shaft seal.
3/4 7FHB4P12C7-S 91271207 40
12 1 1FHB4P12C9-S 91271209 44 ■ Durable, precision machined stainless steel shell.
16 1 1FHB4P16C7-S 91271607 43
■ Field selectable motors- 115V or 230V.
22 1-1/2 15FHB4P22C7-S 91272207 50
NOTE: Single phase 1/2 - 2HP motors rated 115/230 volts. ■ Convenient, sturdy carrying handle.
■ Proven ceramic discharge bearing design for high
resistance to abrasive materials and corrosion.
STAINLESS STEEL MODELS ■ Cast iron motor bracket and stainless steel discharge
Single Phase with 1” NPT.
GPM HP
Model No. Order No. Wt. ■ Two piece brass coupling for easy field serviceability.
5 1 1FHB4P5S15-S 91274822 48
8
1/2 5FHB4P8S9-S 91274830 37 Stainless Steel Models Features:
3/4 7FHB4P8S11-S 91274848 42
3/4 7FHB4P12S7-S 91274855 40 All of the Cast Iron features except:
12 1 1FHB4P12S9-S 91274863 44 ■ Stainless Steel motor bracket and discharge with 1”NPT.
16 1 1FHB4P16S7-S 91274871 43
■ Two piece stainless steel coupling for easy field
22 1-1/2 15FHB4P22S7-S 91274889 50
serviceability.
■ Viton mechanical shaft seal for added chemical resistance.
Centrifugal Pumps
5-11/16” A B
7-1/2”
3-1/2”
H4 Series
Horizontal Booster Pumps
Ordering Information
H4 HORIZONTAL BOOSTER PUMPS with OPEN DRIP PROOF MOTORS
SINGLE PHASE THREE PHASE - 208-230/460 VOLT
GPM HP
Model No. Order No. Wt. Model No. Order No. Wt.
1/3 3FH4P57-S 91241507 35 3FH4P57-T 91243507 35
5 1/2 5FH4P510-S 91241510 37 5FH4P510-T 91243510 37
3/4 7FH4P514-S 91241514 42 7FH4P514-T 91243514 41
1 1FH4P518-S 91241518 46 1FH4P518-T 91243518 44
1/3 3FH4P104-S 91242104 25 3FH4P104-T 91243104 31
1/2 5FH4P106-S 91242106 36 5FH4P106-T 91243106 36
10 3/4 7FH4P109-S 91242109 39 7FH4P109-T 91243109 38
1 1FH4P1012-S 91242112 45 1FH4P1012-T 91243112 43
1-1/2 15FH4P1016-S 91242116 51 15FH4P1016-T 91243116 51
1/2 5FH4P185-S 91242805 36 5FH4P185-T 91243805 36
3/4 7FH4P187-S 91242807 39 7FH4P187-T 91243807 38
18 1 1FH4P189-S 91242809 43 1FH4P189-T 91243809 42
1-1/2 15FH4P1812-S 91242812 51 15FH4P1812-T 91243812 49
2 2FH4P1815-S 91242815 55 2FH4P1815-T 91243815 55
3/4 7FH4P255-S 91243505 38 7FH4P255-T 91244505 37
1 1FH4P256-S 91243506 42 1FH4P256-T 91244506 40
25 1-1/2 15FH4P259-S 91243509 49 15FH4P259-T 91244509 47
2 2FH4P2511-S 91243511 54 2FH4P2511-T 91244511 54
3 3FH4P2516-S 91243516 65 3FH4P2516-T 91244516 64
NOTE: Single Phase 1/3 - 2HP motors rated 115/230V. Single Phase 3HP motor rated 230V. Three Phase motors rated 208-230/460V.
600 40
250
1HP
EFFICIENCY %
550 BEST EFFICIENCY RANGE 30
500 20
200
450 3/4HP 10
400
TOTAL HEAD - FEET
150 350
1/2HP
PSI
300
250
1/3HP
100
200
150 30
NPSHR - FEET
50
100 20
NPSHR
50 10
0 2 4 6 8
CAPACITY - GALLONS PER MINUTE
10 GPM Performance
H4 Horizontal Booster Pumps
250
550
BEST EFFICIENCY RANGE
1-1/2HP
500 50
EFFICIENCY %
200
450 40
400 1HP 30
TOTAL HEAD - FEET
150 350 20
PSI
300 3/4HP
250
100
200 1/2HP
150 1/3HP 30
NPSHR - FEET
50
100 20
NPSHR
50 10
0 2 4 6 8 10 12 14 16
2HP
EFFICIENCY %
400 40
1-1/2HP
350 30
150
TOTAL HEAD - FEET
300 20
1HP
PSI
250
100
3/4HP
200 30
NPSHR - FEET
1/2HP
150 20
50
100 10
NPSHR
50 0
0 4 8 12 16 20 24
25 GPM Performance
H4 Horizontal Booster Pumps
600 60
250
550 50
EFFICIENCY %
500 BEST EFFICIENCY RANGE 40
3HP
200
450 30
400 20
TOTAL HEAD - FEET
150 350
2HP
PSI
300
1-1/2HP
250
100
200 30
1HP
NPSHR - FEET
150 3/4HP 20
50
NPSHR 10
100
50 0
0 8 16 24 32
CAPACITY - GALLONS PER MINUTE
50 GPM
B C
2” TAPPING
HP A (In inches)
Dimensions
1 Phase 3 Phase 1 Phase 3 Phase
SUCTION
75 GPM
B C
HP A
1 Phase 3 Phase 1 Phase 3 Phase
3 14-7/8” 12-7/8” 12-1/8” 27-3/4” 27”
19/32
5 20-1/2” 15-3/4” 14-1/2” 36-1/4” 35”
7-1/2 23-7/8” 15-7/8” 22-3/8” 39-3/4” 46-1/4”
NOTE: Shaft turns counter clockwise if viewed from above motor
Centrifugal Pumps
V6 Series
High Pressure Vertical Booster Pumps
Ordering Information
V6 VERTICAL BOOSTER PUMPS with OPEN DRIP PROOF MOTORS
SINGLE PHASE THREE PHASE - 208-230/460 VOLT
GPM HP
Model No. Order No. Wt. Model No. Order No. Wt.
1-1/2 15FVB6P50-2-S 91303915 100 15FVB6P50-2-T 91304913 103
1-1/2 - 7-1/2 HP V6 SERIES BOOSTER PUMP ENDS V6 BOOSTER PUMPS - 575 VOLT
PUMP ENDS ONLY THREE PHASE - 575 VOLT
GPM HP
Model No. Order No. Wt. Model No. Order No. Wt.
1-1/2 15FVB6P50-2 91304053 65 15FVB6P50-2-T5 91309019 103
250 575
EFFICIENCY %
7-1/2HP
550 60
225 525 50
500 40
475
200
450
425
175 400
5HP
375
150 350
TOTAL HEAD - FEET
325
300
125
275
PSI
250
100 225 3HP
200
75 175 2HP
150
125
50 1-1/2HP
100
75
25 50
25
0 0 30
NPSHR
20
10
0
0 10 20 30 40 50 60 70 80
CAPACITY - GALLONS PER MINUTE
75 GPM Performance
V6 High Pressure Vertical Booster Pumps
EFFICIENCY %
60
350 7-1/2HP 50
150
325 40
300
125
275
250
100
5HP
TOTAL HEAD - FEET
225
200
PSI
75 175
150
125
50 3HP
100
75
25
50
25 20
NPSHR
0 0 10
0
0 10 20 30 40 50 60 70 80 90 100 110
CAPACITY - GALLONS PER MINUTE
Features:
■ Self-priming with large 1” priming port
■ Non-corrosive thermoplastic case with engineered-flow,
high-efficiency, low-noise design
■ High performance, thermoplastic hydraulics, including
floating eye seal and stainless steel impeller wear ring
■ 1-1/2” FNPT threaded suction and discharge
■ Built in drain plug to facilitate servicing/winterizing
■ Square-flange motor design
■ Easy motor toggle switch changes from 230V to 115V
A without rewiring (Not available on 2HP)
2.70
■ Available in 3/4, 1, 1-1/2, and 2HP
o
■ Handles water temperatures up to 120 F and working
pressure up to 75 PSI
Ordering Information
SELF-PRIMING LAWN SPRINKLER PUMPS
PUMP UNIT
11.83
Model HP Voltage
9.75
TY Series Performance
Self Priming Sprinkler Pumps - Thermoplastic
METERS
FEET
PSI
120
35 50
110
TOTAL DYNAMIC HEAD
30 100
40
90
25
80
2HP
30 70
20
60
1½HP
15 50
20
40
1HP
10
30
¾HP
10
20
5
10
0 0 0
0 10 20 30 40 50 60 70 80 90 GPM
CAPACITY
Features:
■ Heavy duty cast iron case with engineered high efficiency,
quiet run design
■ High performance, thermoplastic hydraulics, including
floating eye seal and stainless steel impeller wear ring
■ 1-1/2” FNPT threaded suction and discharge ports
■ Self-priming with large 1” priming port
■ Built in drain plug to facilitate servicing/winterizing
o
■ Handles water temperatures up to 120 F and working
pressure up to 75 PSI
■ All models have 2 compartment motors
■ Easy motor toggle switch changes from 230V to 115V
without rewiring (Not available on 2HP)
A
2.70
Ordering Information
SELF-PRIMING LAWN SPRINKLER PUMPS
11.83
PUMP UNIT
9.75
Model HP Voltage
Order No. Wt.
7FPTYCI 3/4 115/230 93373007 51
3.00
FEET
PSI
120
35 50
110
TOTAL DYNAMIC HEAD
30 100
40
90
25
80
2HP
30 70
20
60
1½HP
15 50
20
40
1HP
10
30
¾HP
10
20
5
10
0 0 0
0 10 20 30 40 50 60 70 80 90 GPM
CAPACITY
Features:
■ Stub Shaft motor with bronze coupling and bronze impeller
offers easy serviceability and premium construction features
■ Cast iron pump case, large capacity case ensures excellent
self-priming performance
■ Thermoplastic diffuser for improved pressures
■ Mechanical shaft seal ensures leakproof fit and continuous
water lubrication
7-7/8
■ Two-compartment motor for easy service. All motors are
single phase 115/230V
11-1/2
8-3/8
Ordering Information
SELF-PRIMING LAWN SPRINKLER PUMPS
Suction x Pump Unit
Note: Dimensions will vary according to motor manufacturer. HP Voltage
Discharge Order No. Wt.
1 1-1/2” x 1-1/2” 115/230 93371876 56
1-1/2 2” X 1-1/2” 115/230 93371884 61
2 2” X 1-1/2” 230 93371892 65
Centrifugal Pumps
HJ Series Performance
Self Priming Sprinkler Pumps
METERS
FEET
PSI
1-1/2HP
120 BEST EFFICIENCY RANGE
50 35 2HP
110
1HP
30 100
40
90
25 80
30 70
20
60
15 50
20
40 10
10
30
NPSHR
10
20 5
5
10
0 0 0 0
0 10 20 30 40 50 60 70 GPM
Features:
■ Available in high head or medium head performance.
■ Easy-service, back pull-out design.
■ Rugged construction with bronze impeller, heavy-duty motor,
and mechanical seal.
■ Suction flange check valves included with each unit.
B
C 9-1/2
Discharge E 4-3/4
3-15/16
4-1/2
Dimensions (In inches)
Suction
7/8
13-1/4
1/4 NPT Model A B C D E F
9-3/4
5-1/4
7-7/16 3SPC 6 20-3/4 15 2-1/4 8-1/8 6-1/2
1/2
5SPC 7 21-3/4 15-1/2 2-3/4 9 7
3-3/4 3-3/4
D D 12-3/4
9
Note: Overall length (B) is shown for single phase motors.
A
F
Ordering Information
HIGH HEAD
Model No. Ordering No. HP Suction Size Discharge Size Volts Phase Weight
3SPCH-S2 9312-7595 3 2 1-1/2 208/230 1 144
3SPCH-T 9312-7603 3 2 1-1/2 208/230/460 3 144
5SPCH-S2 9312-7637 5 2-1/2 2 208/230 1 165
5SPCH-T 9312-7652 5 3 2-1/2 208/230/460 3 133
MEDIUM HEAD
3SPCM-S2 9312-7611 3 2-1/2 2 208/230 1 144
3SPCM-T 9312-7629 3 2-1/2 2 208/230/460 3 144
5SPCM-S2 9312-7660 5 3 2-1/2 208/230 1 165
5SPCM-T 9312-7678 5 3 2-1/2 208/230/460 3 133
Centrifugal Pumps
70 160
60 140
120
50
TOTAL HEAD - FEET
100
40
PSI
80
30
60
5SPCH
20
40 5SPCM
3SPCH 3SPCM
10
20
0 0
40 80 120 160 200 240
CAPACITY - GALLONS PER MINUTE
Features:
■ Available in Cast Iron(DDD Series) or Stainless Steel
(DDS Series) models.
E
D All of the DDD Series features above except:
1-5/16
1-13/16 ■ Viton Mechanical shaft seal for added chemical resitance.
F
2
13/32
■ 304SS Case and seal plate.
G
9/16
15/32 4-7/16
6-1/2
Dimensions
Suct. Disch.
H.P. A B C D E F G H
(NPT) (NPT)
1/2 1-1/4” 1” 14-11/16” 2-3/8” 5-5/16” 4-7/16” 3-1/2” 4-5/8” 8-3/4” 5-1/2”
3/4 1-1/4” 1” 14-11/16” 2-3/8” 5-5/16” 4-7/16” 3-1/2” 4-5/8” 8-3/4” 5-1/2”
1 1-1/4” 1” 14-11/16” 2-3/8” 5-5/16” 4-7/16” 3-1/2” 4-5/8” 8-3/4” 5-1/2”
1-1/2 1-1/4” 1” 15-3/16” 2-3/8” 5-5/16” 4-7/16” 3-1/2” 4-5/8” 8-3/4” 5-1/2”
2 1-1/2” 1-1/4” 16-11/16” 2-13/16” 6-1/8” 5” 3-9/16” 5” 9-1/8” 6-5/16”
2-1/2 2” 1-1/2” 16-11/16” 2-13/16” 6-1/8” 5” 3-9/16” 5” 9-1/8” 6-5/16”
Centrifugal Pumps
DDD/DDS Series
End Suction Centrifugal Pumps
60 140
5.95” DIA
100
40 5.25” DIA
5.00” DIA
80
4.61” DIA
30
60
20
40
NPSHR – FEET
0 0 10
1/2-1-1/2HP
5
2-2-1/2HP
0
0 10 20 30 40 50 60 70 80 90 100
GPM
Capacities GPM
Suction Shut Off
HP 30 35 40 45 50 60 70 80 90 100 110
x Discharge Head
Total Head - Feet
1/2 1-1/4” x 1” 30 27 25 22 19 14 - - - - - 74
3/4 1-1/4” x 1” - 41 38 36 34 29 23 16 - - - 93
1 1-1/4” x 1” - - - 42 40 36 31 25 18 - - 105
1-1/2 1-1/4” x 1” - - - - 52 47 44 39 34 25 - 118
2 1-1/2” x 1-1/4” - - - - - - 64 56 47 36 23 121
2-1/2 2” x 1-1/2” - - - - - - 68 61 53 45 35 131
D
Features:
■ Heavy-duty cast iron body for increased durability.
■ DA1A through DB2 have a bronze impeller.
■ DB3 and DC4 have cast iron impeller.
■ 1/3 - 2HP models have 56C frame motors with shaft coupling
design for easy removal of pump motor.
NRTL/C ■ 5 - 50HP models have JM frame motors with shaft sleeve/O-Ring
CSA108 design for added protection against shaft damage.
UL778
■ 3HP models can use either JM frame or 56 frame motors.
■ Single or three phase motors available on selected models.
■ Sealed motor bearings on all motors to carry radial and thrust
loads of pump end.
■ All units are equipped with open drip-proof motors.
■ Max operating pressures 150 PSI.
o
■ Maximum operating temperature of 212 F on all models.
Performance Curve
300
250
DC1-1/2 DC4
200
FEET OF HEAD
150 DB2
DB1
DB1-1/2
100
DB3
DA1A
50 DA1B
DDD
50 100 150 200 250 300 350 400 450 500 550 600 650
CAPACITY - U.S. GALLONS PER MINUTE
D Series
End Suction Centrifugal Pumps
11
16 15
32
2 SLOTS FOR
1
4
5
5
6
3/8 DIA. BOLTS 2 HOLES FOR
4
3/8 DIA. BOLTS
23
13
8
16
C C
SUCTION E DISCHARGE D D DISCHARGE (NPT)
(NPT) (NPT)
C C C
B B G B G
16
5
F F
DISCHARGE SUCTION
E C
D
DB1-DC4
Notes: 1) Dimensions shown are for units using 60 cycle open-dripproof JM frame motors, 3500 RPM.
2) Total pump length will vary with motor manufacturer.
120
50
30 50% 1 BHP
4 -1/8 DIA.
PSI
60
3 -13/16 DIA. 57%
.75 BHP
20 58%
40 40
NPSHR - FEET
.5 BHP
30
10 .33 BHP
20 20
NPSHR
10
0
0 5 10 15 20 25 30 35 40
CAPACITY - GALLONS PER MINUTE
D
Centrifugal Pumps
62%
100
4-11/16 DIA.
60%
40
55%
80 4-1/4 DIA.
TOTAL HEAD - FEET
65%
30 4 DIA. 66%
PSI
60 2 BHP
3-3/4 DIA.
20 1.5 BHP
40 40
NPSHR - FEET
1 BHP
.5 BHP 30
.75 BHP
10
20 20
NPSHR
10
0
0 10 20 30 40 50 60 70 80
CAPACITY - GALLONS PER MINUTE
120
110 250
100
90
200
80 6-7/16 DIA.
70 50%
TOTAL HEAD - FEET
50 56%
100 5-3/16 DIA.
40 4-3/4 DIA. 58%
30 3 BHP
4-1/4 DIA.
50
20 2 BHP
10 1.5 BHP
1 BHP
NPSHR - FEET
0 0 .75 BHP 30
20
NPSHR
10
0 10 20 30 40 50 60 70 80 GPM
CAPACITIES - GALLONS PER MINUTE
D
Centrifugal Pumps
90
200
100
4-5/8” DIA. 68%
4-5/16” DIA.
30
PSI
3 BHP
10
1.5 BHP 2 BHP
1 BHP
0 40
NPSHR - FEET
30
20
NPSHR
10
350
150
50%
250 20 BHP
200
15 BHP
PSI
6-5/8" DIA.
75
150
5-13/16" DIA.
40
50 10 BHP
NPSHR – FEET
5-1/16" DIA.
100 30
20
7.5 BHP
25 NPSHR
50 5 BHP 10
50%
3 BHP
D
Centrifugal Pumps
120
7-15/16” DIA.
60%
250
7-1/4” DIA. 65%
100
200
80 65%
6-7/16” DIA.
70%
150 60%
TOTAL HEAD - FEET
60 5-13/16” DIA.
70%
20 BHP
PSI
72%
5-1/8” DIA.
100
15 BHP
40
4-1/2” DIA.
4” DIA. 10 BHP
7.5 BHP
50
20
3-13/16” DIA. 5 BHP
3 BHP
2 BHP
NPSHR - FEET
0 0 30
NPSHR 20
10
70
50 74% 68%
5-3/16” DIA. 64%
100
TOTAL HEAD - FEET
60%
4-15/16” DIA. 55%
PSI
75 50%
30
4-1/2” DIA.
50 20 BHP 40
NPSHR - FEET
15 BHP
30
10 BHP
25 7.5 BHP 20
10 5 BHP
NPSHR
10
0 0
0 100 200 300 400 500 600 700 800
D
Features:
■ Epoxy-coated cast iron impeller for maximum efficiency.
o
■ Mechanical shaft seal for water temperatures up to 212 F.
■ 4" NPT suction/discharge on 20-30 HP units.
■ Flanged 5" suction / 4" discharge on 40-50 HP units.
■ 20-50 HP pump end kits are available with either NPT
suction/discharge or flanged suction/discharge connections.
■ Maximum operating pressure of 150 PSI.
■ External balance line.
Centrifugal Pumps
50DC4 75
25DC4
EFFICIENCY
70
20DC4
65
60
40DC4
30DC4
140 325
120 275
IMP. DIA. 8-7/16
110 250
TOTAL HEAD - FEET
100
225 IMP. DIA. 7-7/8 50 HP
90
PSI
200
IMP. DIA. 7-15/32
80 40 HP
175
IMP. DIA. 7-1/32
70
150 30 HP
60
125 25 HP
50
100
40 20 HP
75
30
50DC4 50
40DC4
40
BRAKE HP
30DC4
25DC4 30
20DC4
20
10
20
NPSHR
10
0 50 100 150 200 250 300 350 400 450 500 550 600 650
CAPACITY - GALLONS PER MINUTE
Capacities GPM
DC4 Shut-off
Total Head in Feet Head
(Ft.)
Model HP Imp. Dia. 90 100 120 140 150 160 170 180 190 200 210 220 240 260 280 290
20DC4 20 7-1/32” 650 620 545 430 350 200 165
25DC4 25 7-15/32” 650 595 550 500 450 350 190
30DC4 30 7-7/8” 650 620 590 545 500 430 320 215
40DC4 40 8-7/16” 640 605 560 515 375 260
50DC4 50 9-1/32” 660 600 515 400 280 300
Note: All performance data based on rated nameplate voltage.
DC1-1/2 2" x 1-1/2" 7-1/2 75FPDC1-1/2-S 93160855 162 75FPDC1-1/2-T 93160889 132
10 10FPDC1-1/2-S 93161168 190 10FPDC1-1/2-T 93160897 171
15 Not Available in Single Phase 15FPDC1-1/2-T 93160905 175
1-1/2 15FPDB2-S 93160657 57 15FPDB2-T 93160707 57
2 2FPDB2-S 93160665 60 2FPDB2-T 93160715 60
3 3FPDB2-S 93160673 80 3FPDB2-T 93160723 72
5 5FPDB2-S 93160681 119 5FPDB2-T 93160731 110
DB2 3" x 2"
7-1/2 75FPDB2-S 93160699 150 75FPDB2-T 93160749 116
10 10FPDB2-S 93161150 171 10FPDB2-T 93160756 146
15 Not Available in Single Phase 15FPDB2-T 93161051 210
20 Not Available in Single Phase 20FPDB2-T 93161069 243
5 5FPDB3-S 93167330 132 5FPDB3-T 93167363 95
7-1/2 75FPDB3-S 93167348 160 75FPDB3-T 93167371 120
D
Maximize your flexibility and response time for standard or
special applications using end suction centrifugal pumps...
industrial use, transfer circulation or booster service.
Features:
■ Each kit has a maximum O.D. impeller that can be trimmed
to satisfy any of several horsepower requirements,
thus eliminating the need to stock a complete unit for
each horsepower. Note: Impellers should be balanced
after trimming.
■ A case, bracket, and hardware kit come with each kit to build
a complete pump (motor not included).
■ DC4 20 - 50HP pump end kits are available with either NPT
suction/discharge or flanged suction/discharge. All other
models are NPT only.
■ Heavy-duty cast iron body for increased durability.
■ DA1A, DA1B, DB1-1/2, DC1-1/2, and DB2 Series are fitted
with bronze impeller.
■ DB3 is fitted with cast iron impeller.
■ DC4 is fitted with epoxy coated cast iron impeller.
■ DDD models include thermoplastic impellers.
■ 1/3 - 2HP models have 56C frame motors with shaft
coupling design for easy removal. (Except DDD models
which have 56Z frame motors.)
■ 5 - 50HP models have JM frame motors with shaft sleeve/
o-ring design for added protection against shaft damage.
■ 3HP models can use either JM or 56 frame motors.
■ Mechanical shaft seal handles water temperatures up to
o
212 F. Note: For higher temperature applications, consult
your mechanical seal supplier.
■ Max. operating working pressure is 150 PSI.
■ All models are 3500 RPM. Models DB1, DB1-1/2, and DB2
are also available in 1750 RPM.
D SERIES CENTRIFUGAL PUMP END KITS for 3500 R.P.M. - O.D.P. MOTORS
Suction x HP Motor Frame Max. Imp. PUMP END KIT
Series Phase
Discharge Range Size Diameter Model No. Order No. Wt.
DA1A 1-1/4” x 1” 1/3 - 1 1 or 3 56C 5-1/16” FPDA1A-K1 93167413R011 15
DA1B 1-1/4” x 1” 1/2 - 2 1 or 3 56C 5-1/16” FPDA1B-K1 93167413R021 15
3/4 - 3 1 or 3 56C 6-1/8” FPDB1-K1 93167413R032 25
DB1 1-1/2" x 1" 5 3 182JM
6-7/16” FPDB1-K2 93167413R053 35
5 1 184JM
1-3 1 or 3 56C 5-1/8” FPDB1-1/2-K1 93167413R072 30
5 3 182JM
DB1-1/2 2" x 1-1/2" 5 1 184JM 6-7/16” FPDB1-1/2-K2 93167413R083 40
7-1/2 3 184JM
7-1/2 1 213JM 6-7/16” FPDB1-1/2-K3 93167413R093 45
3 3 145JM
3 1 182JM
5-3/16” FPDC1-1/2-K2 93167413R133 45
5 3 182JM
5 1 184JM
DC1-1/2 2" x 1-1/2" 7-1/2 3 184JM 6-5/8” FPDC1-1/2-K2A 93167413R143 45
7-1/2 1 213JM 6-5/8” FPDC1-1/2-K3A 93167413R163 55
10 3 213JM
10 1 215JM 8-3/8” FPDC1-1/2-K3 93167413R173 55
15 3 215JM
1-1/2 - 3 1 or 3 56C 4-1/2” FPDB2-K1 93167413R102 40
5 3 182JM
5 1 184JM 5-3/16” FPDB2-K2 93167413R113 50
7-1/2 3 184JM
DB2 3" x 2" 7-1/2 1 213JM
10 3 213JM 6-7/16” FPDB2-K3 93167413R123 60
10 1 215JM
15 3 215JM 7-1/4” FPDB2-K3A 93167413R193 65
20 3 254JM 7-15/16” FPDB2-K4 93167413R204 70
5 3 182JM
5 1 184JM 4-15/16” FPDB3-K2 93167413R215 60
7-1/2 3 184JM
7-1/2 1 213JM
DB3 4" x 3"
10 3 213JM
5-3/4” FPDB3-K3 93167413R225 70
10 1 215JM
15 3 215JM
20 3 254JM 6” FPDB3-K4 93167413R236 75
20 3 254JM
7-15/32” FPDC4-K4 93167413R277 145
25 3 256JM
4" x 4" 30 3 284JM
40 3 286JM 9-1/32” FPDC4-K5 93167413R288 155
50 3 324JM
DC4 20 3 254JM
7-15/32” FPDC4-K4F 93167413R297 160
25 3 256JM
5" x 4" Flanged 30 3 284JM
40 3 286JM 9-1/32” FPDC4-K5F 93167413R308 170
50 3 324JM
Notes: Maximum O.D. impeller supplied with P.E. Kits. Impeller must be trimmed to match motor H.P.
Refer to performance curves for specific impeller trim diameters.
Consult catalog for specific trims sizes and performance. Impellers should be rebalanced after trimming.
D
Centrifugal Pumps
D Series
Pump End Kits - Ordering Information
D SERIES CENTRIFUGAL PUMP END KITS for 1750 R.P.M. - O.D.P. MOTORS
Suction x HP Motor Frame Max. Imp. PUMP END KIT
Series Phase
Discharge Range Size Diameter Model No. Order No. Wt.
DB1 1-1/2" x 1" 1/3 - 1/2 1 or 3 56C 6-7/16” FPDB1-K1 93167413R242 25
K5 284-286-324-326JM
20
6-7/16” DIA.
50%
40
6-1/8” DIA. 52%
15
54%
TOTAL HEAD - FEET
52%
30
50%
56%
PSI
10 .5 BHP
20
.3 BHP
NPSHR - FEET
5
10 20
NPSHR
10
0 5 10 15 20 25 30 35 40
CAPACITY - GALLONS PER MINUTE
D
Centrifugal Pumps
20
6-7/16” DIA.
60%
40 65%
5-3/4” DIA.
67%
15
65%
TOTAL HEAD - FEET
30
60%
5-1/8” DIA.
55%
68%
PSI
10 4-5/8” DIA.
20 1 BHP 30
NPSHR - FEET
20
.75 BHP
5
10 .5 BHP 10
NPSHR .3 BHP
20
6-7/16” DIA.
60%
65%
40
70%
15 5-13/16” DIA.
70%
TOTAL HEAD - FEET
30 72%
65%
5-1/8” DIA.
PSI
20 40
1.5 BHP
NPSHR - FEET
1 BHP 30
.75 BHP
5
10 20
.5 BHP
NPSHR 10
Features:
■ 1-1/2” - 10” discharge sizes
■ Capacities to 7000 GPM, 480’ TDH
■ Horsepower: Up to 200 HP
■ Standard ductile iron construction with bronze wear ring
and sleeve
■ Replaceable wear rings
■ Superior NPSH characteristics
Model Number Explanation
■ 150# rated flat faced flanges
Example: 7HC31575-CCPHAA
7 = 7.5 Horsepower (CC only) ■ Heavy wall construction
HC = Horizontal Centrifugal ■ Grade 5 capscrews
3 = Suction Size
■ HC75 & HC10 Series- Enclosed impellers, internally
15 = Discharge Size hydraulically balanced
75 = Nominal Impeller Dia.
CC = Close Coupled ■ Double volute on HC10x10-14, for balanced radial forces,
HC14 Series- External balance line standard
P = Shaft Sealing:
P=Packing ■ Standard with graphite packing or single mechanical seal
M=Mechanical Seal
HAA = Impeller Diameter (Alpha)
A=0 F=5 L=10
B=1 G=6 M=11
C=2 H=7 N=12
D=3 J=8 P=13
E=4 K=9 Q=14
Ordering Information
7.5” Nominal Impeller Diameter - (CC) Close Coupled w/Electric Motor
Standard Construction: Ductile Iron Casing and Impeller, with Bronze Wear Ring(s) and Shaft Sleeve
Pump Model Suction/Disch Weight
Volute Design Motor Eff. HP-RPM Phase Shaft Sealing Order Number
Size (Lbs.)
Flanged Std. Eff. 3-3600 1 Packing 50031575110 195
Flanged Std. Eff. 5-3600 1 Packing 50031575130 205
HC-3x15-75 3” x 1.5”
Flanged Std. Eff. 7.5-3600 1 Packing 50031575140 215
Flanged Std. Eff. 10-3600 1 Packing 50031575150 248
Flanged Std. Eff. 3-3600 3 Packing 10031575110 195
Flanged Std. Eff. 5-3600 3 Packing 10031575130 205
HC-3x15-75 3” x 1.5”
Flanged Std. Eff. 7.5-3600 3 Packing 10031575140 215
Flanged Std. Eff. 10-3600 3 Packing 10031575150 248
Flanged Std. Eff. 3-3600 1 Mech Seal 51031575111 195
Flanged Std. Eff. 5-3600 1 Mech Seal 51031575131 205
HC-3x15-75 3” x 1.5”
Flanged Std. Eff. 7.5-3600 1 Mech Seal 51031575141 215
Flanged Std. Eff. 10-3600 1 Mech Seal 51031575151 248
Flanged Std. Eff. 3-3600 3 Mech Seal 11031575111 195
Flanged Std. Eff. 5-3600 3 Mech Seal 11031575131 205
HC-3x15-75 3” x 1.5”
Flanged Std. Eff. 7.5-3600 3 Mech Seal 11031575141 215
Flanged Std. Eff. 10-3600 3 Mech Seal 11031575151 248
Flanged Std. Eff. 3-3600 1 Packing 50030275100 190
Flanged Std. Eff. 5-3600 1 Packing 50030275110 200
HC-3x2-75 3” x 2”
Flanged Std. Eff. 7.5-3600 1 Packing 50030275130 210
Flanged Std. Eff. 10-3600 1 Packing 50030275140 243
Flanged Std. Eff. 3-3600 3 Packing 10030275100 190
Flanged Std. Eff. 5-3600 3 Packing 10030275110 200
HC-3x2-75 3” x 2” Flanged Std. Eff. 7.5-3600 3 Packing 10030275130 210
Flanged Std. Eff. 10-3600 3 Packing 10030275140 243
Flanged Std. Eff. 15-3600 3 Packing 10030275150 257
Flanged Std. Eff. 3-3600 1 Mech Seal 51030275101 190
Flanged Std. Eff. 5-3600 1 Mech Seal 51030275111 200
HC-3x2-75 3” x 2”
Flanged Std. Eff. 7.5-3600 1 Mech Seal 51030275131 210
Flanged Std. Eff. 10-3600 1 Mech Seal 51030275141 243
Flanged Std. Eff. 3-3600 3 Mech Seal 11030275101 190
Flanged Std. Eff. 5-3600 3 Mech Seal 11030275111 200
HC-3x2-75 3” x 2” Flanged Std. Eff. 7.5-3600 3 Mech Seal 11030275131 210
Flanged Std. Eff. 10-3600 3 Mech Seal 11030275141 243
Flanged Std. Eff. 15-3600 3 Mech Seal 11030275151 257
Flanged Std. Eff. 7.5-3600 1 Packing 50042575100 225
HC-4x25-75 4” x 2.5”
Flanged Std. Eff. 10-3600 1 Packing 50042575110 258
Flanged Std. Eff. 7.5-3600 3 Packing 10042575100 225
Flanged Std. Eff. 10-3600 3 Packing 10042575110 258
HC-4x25-75 4” x 2.5” Flanged Std. Eff. 15-3600 3 Packing 10042575130 272
Flanged Std. Eff. 20-3600 3 Packing 10042575140 292
Flanged Std. Eff. 25-3600 3 Packing 10042575150 302
Flanged Std. Eff. 7.5-3600 1 Mech Seal 51042575101 225
HC-4x25-75 4” x 2.5”
Flanged Std. Eff. 10-3600 1 Mech Seal 51042575111 258
Flanged Std. Eff. 7.5-3600 3 Mech Seal 11042575101 225
Flanged Std. Eff. 10-3600 3 Mech Seal 11042575111 258
HC-4x25-75 4” x 2.5” Flanged Std. Eff. 15-3600 3 Mech Seal 11042575131 272
Flanged Std. Eff. 20-3600 3 Mech Seal 11042575141 292
Flanged Std. Eff. 25-3600 3 Mech Seal 11042575151 302
NOTES: Viton Seals available. Consult price sheets for list price adders.
There will be an impeller trimming charge applied for any non-standard impeller trim.
Consult price sheets for list price adders.
Centrifugal Pumps
HC Series
Standard Centrifugal Pumps- Close Coupled
HC Series
Standard Centrifugal Pumps- Close Coupled
HC Series
Standard Centrifugal Pumps- Close Coupled
Model HC-3x15-75
90
280
6 FT NPSHR
80
7.5” (10 HP) 30 40 50 8 FT
240 55 58 9 FT
70
7.0” (7.5 HP) 10 FT
58
TOTAL HEAD - METERS
60 200
TOTAL HEAD - FEET
6.5” (5 HP) 55
50 50
160
10 HP
40 5.5” (3 HP)
120 7.5 HP
30
5 HP
80
20 2 HP
3 HP
40
10
SIZE: 3” x 1.5”
IMPELLER DIA: Various
0 SPEED: 3525 RPM
0 10 20 30 40 50 60 70 80 90 100 110 120 130
FLOWRATE U.S. GALLONS PER MINUTE
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29
Model HC-3x2-75
90 300
250 50 6 FT
60
TOTAL HEAD - FEET
20 7.5 HP
3 HP
50 5 HP
10
SIZE: 3” x 2”
IMPELLER DIA: Various
0 0 SPEED: 3550 RPM
0 25 50 75 100 125 150 175 200 225 250 275
FLOWRATE U.S. GALLONS PER MINUTE
0 5 10 15 20 25 30 35 40 45 50 55 60 65
FLOWRATE CUBIC METERS PER HOUR
Centrifugal Pumps
HC Series
Standard Centrifugal Pumps- Close Coupled
Model HC-4x25-75
90
280
80 5 FT NPSHR
7.5” (25 HP) 7 FT
40 50
240 60
70 9 FT
70 75
7.0” (20 HP) 12 FT
77
60 200 15 FT
6.5” (15 HP)
TOTAL HEAD - METERS
75
TOTAL HEAD - FEET
50 160 70
Model HC-4x3-75
90
280 8 FT NPSHR
80
7.5” (30 HP) 40 50 60
240 9 FT
70 70
7.0” (25 HP) 75 10 FT
200 78 12 FT
TOTAL HEAD - METERS
60
TOTAL HEAD - FEET
0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 105 110 115 120 125 130 135 140 145 150 155
Model HC-4x4-75
90
280
80
7.5” (50 HP) 40 11 FT
50 60 12 FT
240 70
70 10 FT 13 FT
7.0” (40 HP) 75
15 FT
TOTAL HEAD - METERS
60 200
TOTAL HEAD - FEET
0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170 180 190 200 210 220 230 240 250 260
Model HC-5x4-75
90
280
15 FT NPSHR
80
7.5” (60 HP)
40 50
240 60
70 70
16 FT
7.0” (50 HP) 80
82 17 FT
TOTAL HEAD - METERS
60 200
TOTAL HEAD - FEET
40
20 HP 60
120
30 50
60 HP
80 25 HP 50 HP
40 HP
20
DO NOT OPERATE CONTINUOUSLY 30 HP
BELOW 350 GPM
40
10
SIZE: 5” x 4”
IMPELLER DIA: Various
0 0 SPEED: 3575 RPM
0 100 200 300 400 500 600 700 800 900 1000 1100 1200 1300
FLOWRATE U.S. GALLONS PER MINUTE
0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170 180 190 200 210 220 230 240 250 260 270 280 290 300 310
HC Series
Standard Centrifugal Pumps- Close Coupled
Model HC-3x2-10
500
150 9 FT NPSH REQ’D
30
10.25” ( 30 HP) 9 FT 40
45
140
450 50 9 FT
130 54
400 9 FT
120
9.0” (25 HP) 9 FT
TOTAL HEAD - METERS
110 54
350
8.5” (20 HP)
100
90 300
8.0” (15 HP)
40 HP
80
250
30 HP
70
7.0” (10 HP)
25 HP
60 200
20 HP
7.5 HP 45
50 10 HP
150
40 11 FT 15 HP SIZE: 3” x 2”
IMPELLER DIA: Various
30 100 SPEED: 3570 RPM
0 25 50 75 100 125 150 175 200 225 250 275
FLOWRATE U.S. GALLONS PER MINUTE
0 5 10 15 20 25 30 35 40 45 50 55 60 65
FLOWRATE CUBIC METERS PER HOUR
Model HC-4x25-10
45
140
40 2 FT NPSHR
10.25” (7.5 HP) 1.5 FT
120 40
50
35 60 2 FT
65 2.5 FT
70
30 100
9.0” (5 HP)
TOTAL HEAD - METERS
65
25
80
8.0” (3 HP) 7.5 HP
20
60 60
7.0” (2 HP)
5 HP
15
40
10 2 HP
3 HP
20
5
SIZE: 4” x 2.5”
IMPELLER DIA: Various
0 0 SPEED: 1780 RPM
0 25 50 75 100 125 150 175 200 225 250 275
FLOWRATE U.S. GALLONS PER MINUTE
0 5 10 15 20 25 30 35 40 45 50 55 60 65
FLOWRATE CUBIC METERS PER HOUR
Model HC-4x25-10
180
560
160 8 FT NPSHR
10.25” (60 HP) 6 FT
480 40 50
140 60 8 FT
9.5” (50 HP) 65 10 FT
70
TOTAL HEAD - METERS
65
8.38” (30 HP)
100 320
8.0” (25 HP) 60 HP
HC Series
Standard Centrifugal Pumps- Close Coupled
Model HC-4x3-10
180
560
6 FT NPSHR
160
10.25” ( 100 HP) 7 FT
45 55
480 9 FT
140 9.75” (75 HP) 65
70
11 FT
72
9.25” (60 HP) 14 FT
TOTAL HEAD - METERS
120 400
TOTAL HEAD - FEET
15 FT
8.75” (50 HP) 70
100 320 65
8” (40 HP)
100 HP
80
240 7” (30 HP)
75 HP
60
55 60 HP
20 HP
160 50 HP
40 40 HP
30 HP
80
20
SIZE: 4” x 3”
IMPELLER DIA: Various
0 SPEED: 3570 RPM
0 80 160 240 320 400 480 560 640 720 800 880
FLOWRATE U.S. GALLONS PER MINUTE
0 8 16 24 32 40 48 56 64 72 80 88 96 104 112 120 128 136 144 152 160 168 176 184 192 200 208
FLOWRATE CUBIC METERS PER HOUR
Model HC-6x4-10
180
560
160
10.25” (125 HP)
480 8 FT NPSHR
140 40 50 60 10 FT
9.75” (100 HP) 70 15 FT
75 12 FT
80
18 FT
TOTAL HEAD - METERS
120 400
TOTAL HEAD - FEET
84
9.0” (75 HP)
80
100 320 8.38” (60 HP) 125 HP
Model HC-8x6-95
11 6.5 FT
35 40 50
9.5 @ 13˚ (7.5 HP) 60
10
70
7 FT
80 9.5 FT
30
9 9.0 @ 15˚ (5 HP)
8 13 FT
25
TOTAL HEAD - METERS
86
TOTAL HEAD - FEET
7
87 7.5 HP
6 20 80
70
5
15
4
60
3 10 5 HP
2 3 HP 50
5
1
SIZE: 8” x 6”
IMPELLER DIA: Various
0 0 SPEED: 1150 RPM
0 100 200 300 400 500 600 700 800 900 1000 1100
FLOWRATE U.S. GALLONS PER MINUTE
Model HC-8x6-95
45
140
40
120
35
TOTAL HEAD - METERS
30 100
7 FT NPSH REQ’D
TOTAL HEAD - FEET
0 40 80 120 160 200 240 280 320 360 400 440 480 520
FLOWRATE CUBIC METERS PER HOUR
Centrifugal Pumps
HC Series
Standard Centrifugal Pumps- Close Coupled
Model HC-8x6-10
70
20
60
TOTAL HEAD - FEET - EFFICIENCY (%)
15 50
TOTAL HEAD - METERS
70
10 HP
20 84
81 7.5 HP
5
10 5 HP
3 HP
SIZE: 8” x 6”
IMPELLER DIA: Various
0 0 SPEED: 1150 RPM
0 100 200 300 400 500 600 700 800 900 1000 1100 1200
FLOWRATE U.S. GALLONS PER MINUTE
0 20 40 60 80 100 120 140 160 180 200 220 240 260 280
FLOWRATE CUBIC METERS PER HOUR
Model HC-8x6-10
45
140
40
120
TOTAL HEAD - FEET - EFFICIENCY(%)
30 100
80%
9.25” (30 HP) 25 FT
25 30 FT
80
9.00” (20 HP)
20
60 70%
81% 40 HP
15
84%
40 30 HP
10 25 HP
20 HP
20 15 HP
5 10 HP
SIZE: 8” x 6”
IMPELLER DIA: Various
0 SPEED: 1760 RPM
0 200 400 600 800 1000 1200 1400 1600 1800 2000 2200
FLOWRATE U.S. GALLONS PER MINUTE
0 40 80 120 160 200 240 280 320 360 400 440 480 520
FLOWRATE CUBIC METERS PER HOUR
Model HC-5x3-14
90
280
5 FT
80
5 FT
240 14.0” (40 HP) 6 FT
70 50% 60% 65%
70% 7 FT
13.0” (30 HP) 73%
TOTAL HEAD - METERS
60 200 9 FT
TOTAL HEAD - FEET
70%
12.0” (25 HP)
50 65% 10.5 FT
160
60%
11.0” (20 HP)
40
120 50%
30 50 HP
15 HP
80 40 HP
20
30 HP
40 25 HP
10 20 HP
SIZE: 5” x 3”
IMPELLER DIA: Various
SPEED: 1780 RPM
0 0
0 80 160 240 320 400 480 560 640 720 800 880
FLOWRATE U.S. GALLONS PER MINUTE
0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170 180 190 200 210
FLOWRATE CUBIC METERS PER HOUR
Model HC-6x4-13
280
80
240
4 FT NPSH REQ’D
80 23 FT
160 76
11.0” (40 HP)
40 60 HP
120 10.0” (30 HP) 83
50 HP
25 HP
40 HP
80
20
30 HP
40
SIZE: 6” x 4”
IMPELLER DIA: Various
0 0 SPEED: 1780 RPM
0 100 200 300 400 500 600 700 800 900 1000 1100 1200 1300
FLOWRATE U.S. GALLONS PER MINUTE
HC Series
Standard Centrifugal Pumps- Close Coupled
Model HC-6x6-14
280
80
240
6 FT 8 FT
14” (100 HP) 10 FT
50 12 FT
200 60
TOTAL HEAD - METERS
60 70 75
TOTAL HEAD - FEET
80 15 FT
13” (75 HP) 82
17 FT
160
12” (60 HP) 80
40 75
11” (50 HP) 70
120
10” (40 HP) 100 HP
80 75 HP
20 30 HP 60 HP
50 HP
40 HP
40
SIZE: 6” x 6”
IMPELLER DIA: Various
0 0 SPEED: 1760 RPM
250 500 750 1000 1250 1500 1750 2000 2250 2500 2750
FLOWRATE U.S. GALLONS PER MINUTE
0 50 100 150 200 250 300 350 400 450 500 550 600 650
FLOWRATE CUBIC METERS PER HOUR
Model HC-8x6-14
140
40
120
4 FT NPSH REQ’D
100 5.5 FT
30
TOTAL HEAD - METERS
40 50 60 7.5 FT
70 75 80
85 87
13” (30 HP)
80 11 FT
85
12” (25 HP)
20 80
50 HP
60
11” (20 HP)
40 HP
15 HP
40 30 HP
10 25 HP
20 HP
20
SIZE: 8” x 6”
IMPELLER DIA: Various
SPEED: 1170 RPM
0 0
0 200 400 600 800 1000 1200 1400 1600 1800 2000 2200 2400
FLOWRATE U.S. GALLONS PER MINUTE
0 40 80 120 160 200 240 280 320 360 400 440 480 520 560
FLOWRATE CUBIC METERS PER HOUR
Model HC-8x6-14
350
100
300
TOTAL HEAD - METERS
9 FT NPSH REQ’D
TOTAL HEAD - FEET
75 250
12 FT 14 FT
14.0” (150 HP) 17 FT
60 70 75
200 80 85
13.0” (125 HP) 87 25 FT
85
50 12.0” (100 HP)
150 80
11.0” (75 HP)
150 HP
100 60 HP 125 HP
25 100 HP
75 HP
50
SIZE: 8” x 6”
IMPELLER DIA. Various
SPEED: 1780 RPM
0 0
500 1000 1500 2000 2500 3000 3500 4000 4500 5000 5500
FLOWRATE U.S. GALLONS PER MINUTE
0 100 200 300 400 500 600 700 800 900 1000 1100 1200 1300
FLOWRATE CUBIC METERS PER HOUR
Centrifugal Pumps
HC Series
Standard Centrifugal Pumps- Close Coupled
Model HC-10x10-14
140
40
120
7 FT NPSH REQ’D
100
TOTAL HEAD - METERS
30
TOTAL HEAD - FEET
0 100 200 300 400 500 600 700 800 900 1000
FLOWRATE CUBIC METERS PER HOUR
Model HC-10x10-14
280 80
80
12 FT NPSH REQ’D
240 70
70
TOTAL HEAD -FEET
75
80 20 FT
13” (150 HP)
EFFICIENCY
85
160 50
25 FT
87
12” (125 HP)
40 85
120 40
11” (100 HP) 80
75
200 HP
80 150 HP 30
20 125 HP
100 HP
75 HP
40 20
0 125 250 375 500 625 750 875 1000 1125 1250 1375
FLOWRATE CUBIC METERS PER HOUR
Features:
■ 1-1/2” - 10” discharge sizes
■ Capacities to 7000 GPM, 480’ TDH
■ Horsepower: Up to 200 HP
■ Standard ductile iron construction with bronze wear ring
and sleeve
■ Replaceable wear rings
■ Superior NPSH characteristics
Model Number Explanation
■ 150# rated flat faced flanges
Example: HC31575-BFP
HC = Horizontal Centrifugal ■ Heavy wall construction
3 = Suction Size ■ Grade 5 capscrews
15 = Discharge Size
■ HC75 & HC10 Series- Enclosed impellers, internally
75 = Nominal Impeller Dia. hydraulically balanced
BF = Bearing Frame
P = Shaft Sealing: ■ Double volute on HC10x10-14, for balanced radial forces,
P=Packing HC14 Series- External balance line standard
M=Mechanical Seal ■ Standard with graphite packing or single mechanical seal
Centrifugal Pumps
HC Series
Standard Centrifugal Pumps- Bearing Frame
Ordering Information
7.5” Nominal Impeller Diameter - (BF) Bearing Frame w/Electric Motor
Standard Construction: Ductile Iron Casing and Impeller, with Bronze Wear Ring(s) and Shaft Sleeve
Pump Model Suction/Disch Size Rotation Shaft Sealing Order Number Weight (Lbs.)
HC-3X15-75-BF-P 3” x 1.5” CW Packing 14031575100 245
HC-3X15-75-BF-M 3” x 1.5” CW Mech Seal 15031575101 245
HC-3X2-75-BF-P 3” x 2” CW Packing 14030275100 245
HC-3X2-75-BF-M 3” x 2” CW Mech Seal 15030275101 245
HC-4X25-75-BF-P 4” x 2.5” CW Packing 14042575100 255
HC-4X25-75-BF-M 4” x 2.5” CW Mech Seal 15042575101 255
HC-4X3-75-BF-P 4” x 3” CW Packing 14040375100 265
HC-4X3-75-BF-M 4” x 3” CW Mech Seal 15040375101 265
HC-4X4-75-BF-P 4” x 4” CW Packing 14040475100 265
HC-4X4-75-BF-M 4” x 4” CW Mech Seal 15040475101 265
HC-5X4-75-BF-P 5” x 4” CW Packing 14050475100 285
HC-5X4-75-BF-M 5” x 4” CW Mech Seal 15050475101 285
300
Model HC-3x15-75
90
270
80
3530 RPM
38 44
240 50
55
3400 RPM 58
70 59
210 59
3200 RPM
58
60
TOTAL HEAD - METERS
55
3000 RPM
TOTAL HEAD - FEET
180
50 50
2800 RPM
150
40
2500 RPM
120
2300 RPM 44 7.5 HP
30
90 2 HP
5 HP
20 3 HP
60 15
NPSHR - FEET
10
30 7.5
NPSHR - 3530 RPM SIZE: 3” x 1.5”
IMPELLER DIA: 7.50”
0 SPEED: 3530 RPM
0
0 10 20 30 40 50 60 70 80 90 100 110 120 130 140
FLOWRATE U.S. GALLONS PER MINUTE
0 5 10 15 20 25 30
FLOWRATE CUBIC METERS PER HOUR
300
Model HC-3x2-75
90
270
80 3550 RPM
50
56
240 3400 RPM 61
64
70 66
60 66
TOTAL HEAD - METERS
3000 RPM
TOTAL HEAD - FEET
180
64
50 2800 RPM
61
150
40 2500 RPM
120
2300 RPM
56
30 10 HP
90
3 HP 50
20 7.5 HP
60 15
5 HP
NPSHR - FEET
10
30 NPSHR - 3550 RPM 7.5
SIZE: 3” x 2”
IMPELLER DIA: 7.50”
0 SPEED: 3550 RPM
0
0 20 40 60 80 100 120 140 160 180 200 220 240 260 280
FLOWRATE U.S. GALLONS PER MINUTE
0 5 10 15 20 25 30 35 40 45 50 55
FLOWRATE CUBIC METERS PER HOUR
Centrifugal Pumps
HC Series
Standard Centrifugal Pumps-Bearing Frame
300
Model HC-4x25-75
90
270
80
3580 RPM
240 57 64
70 70
3400 RPM 74
77
210
3200 RPM
60 77
TOTAL HEAD - METERS
2600 RPM 64
40
120
2400 RPM 57
30
90
25 HP
20 HP
20
NPSHR - FEET
60 15 HP 30
10 HP
10
30 15
7.5 HP
SIZE: 4” x 2.5”
NPSHR - 3580 RPM IMPELLER DIA: 7.50”
0 SPEED: 3580 RPM
0
0 50 100 150 200 250 300 350 400 450 500 550 600 650
FLOWRATE U.S. GALLONS PER MINUTE
Model HC-4x3-75
300
90
270
80
3570 RPM
240 59
65
70 3400 RPM 71
74
76
210 77
3200 RPM
60
TOTAL HEAD - METERS
77
3000 RPM
TOTAL HEAD - FEET
180 76
50 74
2800 RPM
71
150
40 65
2500 RPM
120
2400 RPM
20 HP
30 30 HP
90 25 HP
20
NPSHR - FEET
60 15 HP 30
10 HP
10 7.5 HP
30 15
NPSHR - 3570 RPM SIZE: 4” x 3”
IMPELLER DIA: 7.50”
0 SPEED: 3570 RPM
0
0 50 100 150 200 250 300 350 400 450 500 550 600 650 700 750
FLOWRATE U.S. GALLONS PER MINUTE
300
Model HC-4x4-75
90
270
80
3550 RPM 55 61
240 67
71
70 3400 RPM 74
75
210 75
3200 RPM 74
60
TOTAL HEAD - METERS
71
TOTAL HEAD - FEET
50 67
2800 RPM 61
150
40 2600 RPM
55
120
2300 RPM
30 50.0 HP
90
40.0 HP
20
NPSHR - FEET
60 30.0 HP 30
25.0 HP
20.0 HP
10
30 NPSHR - 3550 RPM 15.0 HP 15
SIZE: 4” x 4”
IMPELLER DIA: 7.50”
0 SPEED: 3550 RPM
0
0 100 200 300 400 500 600 700 800 900 1000
FLOWRATE U.S. GALLONS PER MINUTE
300
Model HC-5x4-75
90
270
80
3580 RPM
240 56
64
70 71
3400 RPM 76
80
210 81
60 3200 RPM 81
80
TOTAL HEAD - METERS
180
3000 RPM
50 76
2900 RPM 71
150
40 64
120
56
30
90
50 HP 60 HP
20 40 HP
60 40
25 HP 30 HP
NPSHR - FEET
10
30 NPSHR - 3580 RPM 20
SIZE: 5” x 4”
IMPELLER DIA: 7.50”
0 SPEED: 3580 RPM
0
0 200 400 600 800 1000 1200 1400
FLOWRATE U.S. GALLONS PER MINUTE
800
Model HC-3x2-10
240
NPSHR - FEET
720 NPSHR - 3570 RPM 10
200
640 5
560
160
3570 RPM
TOTAL HEAD - METERS
37
TOTAL HEAD - FEET
480 43
3400 RPM 48
52
54
55
400 3200 RPM
120 55
54
3000 RPM 52
320 48
2800 RPM
80 2500 RPM
240 30 HP
25 HP
2400 RPM
7.5 HP 20 HP
160
10 HP 15 HP
40
80
SIZE: 3” x 2”
IMPELLER DIA: 10.25”
0 SPEED: Various
0
0 20 40 60 80 100 120 140 160 180 200 220 240 260
FLOWRATE U.S. GALLONS PER MINUTE
0 5 10 15 20 25 30 35 40 45 50 55
FLOWRATE CUBIC METERS PER HOUR
800
Model HC-4x25-10
240
720 30
NPSHR - FEET
200
640 15
NPSHR - 3580 RPM
560 0
160
3580 RPM
TOTAL HEAD - METERS
49
TOTAL HEAD - FEET
480
56
3400 RPM 62
66
69
3200 RPM 70
120 400
69
66
3000 RPM
62
320 2800 RPM
60 HP
80 2500 RPM
240 50 HP
2300 RPM 40 HP
15 HP
160
40 20 HP
25 HP
30 HP
80
SIZE: 4” x 2.5”
IMPELLER DIA: 10”
0 SPEED: 3580 RPM
0
0 50 100 150 200 250 300 350 400 450 500 550 600
FLOWRATE U.S. GALLONS PER MINUTE
HC Series
Standard Centrifugal Pumps-Bearing Frame
Model HC-4x3-10
800
240
NPSHR - FEET
720 20
200
640 10
NPSHR - 3570 RPM
560
160
3570 RPM
TOTAL HEAD - METERS
55
TOTAL HEAD - FEET
480 61
66
3400 RPM 70
72
80
2500 RPM 61
240
75 HP
20 HP 60 HP
25 HP
160
55 50 HP
40 40 HP
30 HP
80
SIZE: 4” x 3”
IMPELLER DIA: 10”
0 SPEED: 3570 RPM
0
0 100 200 300 400 500 600 700 800 900
FLOWRATE U.S. GALLONS PER MINUTE
Model HC-6x4-10
800
240
NPSHR - FEET
720 30
200
640 NPSHR - 3550 RPM 15
560
160
TOTAL HEAD - METERS
3550 RPM 52 61
TOTAL HEAD - FEET
480 69
3400 RPM 75
78
79
400 3200 RPM
120
3000 RPM
320 79
2800 RPM 78
80 2500 RPM
240 75
2400 RPM
75 HP
20 HP
60 HP
160
50 HP
40 69 40 HP
30 HP
80 25 HP
SIZE: 6” x 4”
IMPELLER DIA: 10”
0 SPEED: 3550 RPM
0
0 100 200 300 400 500 600 700 800 900 1000 1100
FLOWRATE U.S. GALLONS PER MINUTE
Model HC-8x6-95
100
90
20 1780 RPM
80 1700 RPM 58
67
75
1600 RPM 81
70
15
TOTAL HEAD - METERS
1500 RPM
TOTAL HEAD - FEET
60 85
81
86
75
50
10 67
40
25 HP
30 20 HP
5 15 HP
NPSHR - FEET
20 40
10 HP
10 20
Model HC-8x6-10
150
NPSHR - FEET
135 40
30
90 1600 RPM
20 82
1500 RPM 84 78
75
15 1400 RPM 73
40 HP
60
10 45
30 HP
30 65 25 HP
20 HP
5 56
15 15 HP
SIZE: 8” x 6”
IMPELLER DIA: 10.25”
0 SPEED: 1780 RPM
0
0 400 800 1,200 1,600 2000
FLOWRATE U.S. GALLONS PER MINUTE
Model HC-5x3-14
110 2200 RPM
350 40 50
60
65
100 70
73
90 300 2000 RPM
70
80
250 65
1800 RPM
TOTAL HEAD - METERS
70 60
60 200
1600 RPM
50
50
150
40 25 HP
75 HP 10
NPSHR - FEET
100 60 HP 8
30 50 HP
NPSHR - 1800 RPM 40 HP
6
20 30 HP
50 4
10
2 SIZE: 5” x 3”
IMPELLER DIA: 14”
0 0 SPEED: Various
0 100 200 300 400 500 600 700 800 900 1000 1100
FLOWRATE U.S. GALLONS PER MINUTE
0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170 180 190 200 210 220 230 240 250 260
FLOWRATE CUBIC METERS PER HOUR
350
Model HC-6x4-13
100
2200 RPM
50 60
300 70
76
80
80 2000 RPM 80
250
76
TOTAL HEAD - METERS
125 HP
TOTAL HEAD - FEET
1800 RPM
60 200
100 HP
1600 RPM
75 HP
150
1400 RPM 60 HP
40
50 HP
40 HP
100 1200 RPM 20
30 HP
10 HP 15 HP 25 HP
20 20 HP
NPSHR
50 10
NPSHR - 1800 RPM
SIZE: 6” x 4”
IMPELLER DIA: 13.0”
0 0 SPEED: Various
0 150 300 450 600 750 900 1050 1200 1350 1500 1650
FLOWRATE U.S. GALLONS PER MINUTE
0 20 40 60 80 100 120 140 160 180 200 220 240 260 280 300 320 340 360 380
FLOWRATE CUBIC METERS PER HOUR
Centrifugal Pumps
HC Series
Standard Centrifugal Pumps-Bearing Frame
Model HC-6x6-14
280
2000 RPM
80 50
60
70
150 HP
240 80
1800 RPM 83
60 200
80
TOTAL HEAD - METERS
1600 RPM
160
75 HP
40 HP
80 20
60 HP
NPSHR - FEET
50 HP
20
15
40 10
NPSHR - 1760 RPM
5 SIZE: 6” x 6”
IMPELLER DIA: 14”
0 0 SPEED: Various
0 250 500 750 1000 1250 1500 1750 2000 2250 2500 2750
FLOWRATE U.S. GALLONS PER MINUTES
0 50 100 150 200 250 300 350 400 450 500 550 600 650
FLOWRATE CUBIC METERS PER HOUR
Model HC-8x6-14
350
8 FT NPSH REQ’D
100 10 FT 12 FT
2100 RPM 17 FT
300 40 50 60 70 75
2000 RPM 80 25 FT
85
87
1900 RPM
75 250 85
TOTAL HEAD - METERS
1800 RPM
TOTAL HEAD - FEET
1700 RPM 80
200
1600 RPM 250 HP
50 200 HP
150
100 HP 150 HP
100
25
50
SIZE: 8” x 6”
IMPELLER DIA: 14”
0 0 SPEED: Various
0 500 1000 1500 2000 2500 3000 3500 4000 4500 5000 5500
FLOWRATE U.S. GALLONS PER MINUTE
0 100 200 300 400 500 600 700 800 900 1000 1100 1200 1300
FLOWRATE CUBIC METERS PER HOUR
Model HC-10x10-14
100
320 2200 RPM
50
280 60
70
80 2000 RPM 80
240
TOTAL HEAD - METERS
85
1800 RPM
60 200
80
1600 RPM
160 30
NPSHR - FEET
40 70
120 20
300 HP
NPSHR - 1800 RPM 250 HP
80 200 HP 10
20 150 HP
125 HP SIZE: 10” x 10”
IMPELLER DIA: 14”
SPEED: Various
40
0 500 1000 1500 2000 2500 3000 3500 4000 4500 5000 5500 6000 6500
FLOWRATE U.S. GALLONS PER MINUTE
0 125 250 375 500 625 750 875 1000 1125 1250 1375 1500
FLOWRATE CUBIC METERS PER HOUR
Features:
■ 2” - 10” discharge sizes
■ Capacities to 7000 GPM, 300’ TDH
■ Horsepower: Up to 200 HP
■ Standard ductile iron construction with bronze wear ring
and sleeve
■ Replaceable wear rings
■ Superior NPSH characteristics
Model Number Explanation
■ 150# rated flat faced flanges
Example: HC4310-SA3P
HC = Horizontal Centrifugal ■ Heavy wall construction
4 = Suction Size ■ Grade 5 capscrews
3 = Discharge Size
■ HC10 Series- Enclosed impellers, internally
10 = Nominal Impeller Dia. hydraulically balanced
SA = SAE Engine Drive
3 = SAE Housing Size ■ Double volute on HC10x10-14, for balanced radial forces,
P = Shaft Sealing: HC14 Series- External balance line standard
P=Packing ■ Standard with graphite packing only
■ Flywheel coupling and taper bushings sold separately.
Centrifugal Pumps
HC Series
Standard Centrifugal Pumps- SAE Engine Drive
Ordering Information
10” Nominal Impeller Diameter - (SA) SAE Mount
Standard Construction: Ductile Iron Casing and Impeller, with Bronze Wear Ring(s) and Shaft Sleeve
Suction/ Shaft Volute Keyed Shaft Clutch Taper Ordering Weight
Pump Model Disch Size Sealing Design Dia x Keyway SAE Size Size Bushing Number (Lbs.)
Packing Flanged 1-7/8” x 1/2” 3 11.5” 2517 16030210103 395
HC-3x2-10 3” x 2” Packing Flanged 1-7/8” x 1/2” 4 10” 2517 16030210104 395
Packing Flanged 1-7/8” x 1/2” 5 8” 2517 16030210105 395
Packing Flanged 1-7/8” x 1/2” 3 11.5” 2517 16042510103 405
HC-4x25-10 4” x 2.5” Packing Flanged 1-7/8” x 1/2” 4 10” 2517 16042510104 405
Packing Flanged 1-7/8” x 1/2” 5 8” 2517 16042510105 405
Packing Flanged 1-7/8” x 1/2” 3 11.5” 2517 16040310103 405
HC-4x3-10 4” x 3” Packing Flanged 1-7/8” x 1/2” 4 10” 2517 16040310104 405
Packing Flanged 1-7/8” x 1/2” 5 8” 2517 16040310105 405
Packing Flanged 1-7/8” x 1/2” 3 11.5” 2517 16060410103 465
HC-6x4-10 6” x 4” Packing Flanged 1-7/8” x 1/2” 4 10” 2517 16060410104 465
Packing Flanged 1-7/8” x 1/2” 5 8” 2517 16060410105 465
Packing Flanged 1-7/8” x 1/2” 1 14” 3535 16080695101 595
HC-8x6-95 8” x 6” Packing Flanged 1-7/8” x 1/2” 3 11.5” 2517 16080695103 595
Packing Flanged 1-7/8” x 1/2” 4 10” 2517 16080695104 595
Packing Flanged 1-7/8” x 1/2” 1 14” 3535 16080610101 600
HC-8x6-10 8” x 6” Packing Flanged 1-7/8” x 1/2” 3 11.5” 2517 16080610103 600
Packing Flanged 1-7/8” x 1/2” 4 10” 2517 16080610104 600
Model HC-3x2-10
800
240
NPSHR - FEET
720 NPSHR - 3570 RPM 10
200
640 5
560
160
3570 RPM
TOTAL HEAD - METERS
37
TOTAL HEAD - FEET
480 43
3400 RPM 48
52
54
55
400 3200 RPM
120 55
54
3000 RPM 52
320 48
2800 RPM
80 2500 RPM
240 30 HP
25 HP
2400 RPM
7.5 HP 20 HP
160
10 HP 15 HP
40
80
SIZE: 3” x 2”
IMPELLER DIA: 10.25”
0 SPEED: Various
0
0 20 40 60 80 100 120 140 160 180 200 220 240 260
FLOWRATE U.S. GALLONS PER MINUTE
0 5 10 15 20 25 30 35 40 45 50 55
FLOWRATE CUBIC METERS PER HOUR
800
Model HC-4x25-10
240
720 30
NPSHR - FEET
200
640 15
NPSHR - 3580 RPM
560 0
160
3580 RPM
TOTAL HEAD - METERS
49
TOTAL HEAD - FEET
480
56
3400 RPM 62
66
69
3200 RPM 70
120 400
69
66
3000 RPM
62
320 2800 RPM
60 HP
80 2500 RPM
240 50 HP
2300 RPM 40 HP
15 HP
160
40 20 HP
25 HP
30 HP
80
SIZE: 4” x 2.5”
IMPELLER DIA: 10”
0 SPEED: 3580 RPM
0
0 50 100 150 200 250 300 350 400 450 500 550 600
FLOWRATE U.S. GALLONS PER MINUTE
HC Series
Standard Centrifugal Pumps-SAE Engine Drive
800
Model HC-4x3-10
240
NPSHR - FEET
720 20
200
640 10
NPSHR - 3570 RPM
560
160
3570 RPM
TOTAL HEAD - METERS
55
TOTAL HEAD - FEET
480 61
66
3400 RPM 70
72
80
2500 RPM 61
240
75 HP
20 HP 60 HP
25 HP
160
55 50 HP
40 40 HP
30 HP
80
SIZE: 4” x 3”
IMPELLER DIA: 10”
0 SPEED: 3570 RPM
0
0 100 200 300 400 500 600 700 800 900
FLOWRATE U.S. GALLONS PER MINUTE
800
Model HC-6x4-10
240
NPSHR - FEET
720 30
200
640 NPSHR - 3550 RPM 15
560
160
TOTAL HEAD - METERS
3550 RPM 52 61
TOTAL HEAD - FEET
480 69
3400 RPM 75
78
79
400 3200 RPM
120
3000 RPM
320 79
2800 RPM 78
80 2500 RPM
240 75
2400 RPM
75 HP
20 HP
60 HP
160
50 HP
40 69 40 HP
30 HP
80 25 HP
SIZE: 6” x 4”
IMPELLER DIA: 10”
0 SPEED: 3550 RPM
0
0 100 200 300 400 500 600 700 800 900 1000 1100
FLOWRATE U.S. GALLONS PER MINUTE
100
Model HC-8x6-95
90
20 1780 RPM
80 1700 RPM 58
67
75
1600 RPM 81
70
15
TOTAL HEAD - METERS
1500 RPM
TOTAL HEAD - FEET
60 85
81
86
75
50
10 67
40
25 HP
30 20 HP
5 15 HP
NPSHR - FEET
20 40
10 HP
10 20
150
Model HC-8x6-10
NPSHR - FEET
135 40
30
90 1600 RPM
20 82
1500 RPM 84 78
75
15 1400 RPM 73
40 HP
60
10 45
30 HP
30 65 25 HP
20 HP
5 56
15 15 HP
SIZE: 8” x 6”
IMPELLER DIA: 10.25
0 SPEED: 1780 RPM
0
0 400 800 1,200 1,600 2000
FLOWRATE U.S. GALLONS PER MINUTE
HC Series
Standard Centrifugal Pumps-SAE Engine Drive
Model HC-5x3-14
110 2200 RPM
350 40 50
60
65
100 70
73
90 300 2000 RPM
70
80
250 65
1800 RPM
TOTAL HEAD - METERS
70 60
60 200
1600 RPM
50
50
150
40 25 HP
75 HP 10
NPSHR - FEET
100 60 HP 8
30 50 HP
NPSHR - 1800 RPM 40 HP
6
20 30 HP
50 4
10
2 SIZE: 5” x 3”
IMPELLER DIA: 14”
0 0 SPEED: Various
0 100 200 300 400 500 600 700 800 900 1000 1100
FLOWRATE U.S. GALLONS PER MINUTE
0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170 180 190 200 210 220 230 240 250 260
350
Model HC-6x4-13
100
2200 RPM
50 60
300 70
76
80
80 2000 RPM 80
250
76
TOTAL HEAD - METERS
125 HP
TOTAL HEAD - FEET
1800 RPM
60 200
100 HP
1600 RPM
75 HP
150
1400 RPM 60 HP
40
50 HP
40 HP
100 1200 RPM 20
30 HP
10 HP 15 HP 25 HP
20 20 HP
NPSHR
50 10
NPSHR - 1800 RPM
SIZE: 6” x 4”
IMPELLER DIA: 13.0”
0 0 SPEED: Various
0 150 300 450 600 750 900 1050 1200 1350 1500 1650
FLOWRATE U.S. GALLONS PER MINUTE
0 20 40 60 80 100 120 140 160 180 200 220 240 260 280 300 320 340 360 380
FLOWRATE CUBIC METERS PER HOUR
Model HC-6x6-14
280
2000 RPM
80 50
60
70
150 HP
240 80
1800 RPM 83
60 200
80
TOTAL HEAD - METERS
1600 RPM
160
75 HP
40 HP
80 20
60 HP
NPSHR - FEET
50 HP
20
15
40 10
NPSHR - 1760 RPM
5 SIZE: 6” x 6”
IMPELLER DIA: 14”
0 0 SPEED: Various
0 250 500 750 1000 1250 1500 1750 2000 2250 2500 2750
FLOWRATE U.S. GALLONS PER MINUTES
0 50 100 150 200 250 300 350 400 450 500 550 600 650
FLOWRATE CUBIC METERS PER HOUR
Model HC-8x6-14
350
8 FT NPSH REQ’D
100 10 FT 12 FT
2100 RPM 17 FT
300 40 50 60 70 75
2000 RPM 80 25 FT
85
87
1900 RPM
75 250 85
TOTAL HEAD - METERS
1800 RPM
TOTAL HEAD - FEET
1700 RPM 80
200
1600 RPM 250 HP
50 200 HP
150
100 HP 150 HP
100
25
50
SIZE: 8” x 6”
IMPELLER DIA: 14”
0 0 SPEED: Various
0 500 1000 1500 2000 2500 3000 3500 4000 4500 5000 5500
FLOWRATE U.S. GALLONS PER MINUTE
0 100 200 300 400 500 600 700 800 900 1000 1100 1200 1300
FLOWRATE CUBIC METERS PER HOUR
Centrifugal Pumps
HC Series
Standard Centrifugal Pumps-SAE Engine Drive
Model HC-10x10-14
100
320 2200 RPM
50
280 60
70
80 2000 RPM 80
240
TOTAL HEAD - METERS
85
1800 RPM
60 200
80
1600 RPM
160 30
NPSHR - FEET
40 70
120 20
300 HP
NPSHR - 1800 RPM 250 HP
80 200 HP 10
20 150 HP
125 HP SIZE: 10” x 10”
IMPELLER DIA: 14”
SPEED: Various
40
0 500 1000 1500 2000 2500 3000 3500 4000 4500 5000 5500 6000 6500
FLOWRATE U.S. GALLONS PER MINUTE
0 125 250 375 500 625 750 875 1000 1125 1250 1375 1500
FLOWRATE CUBIC METERS PER HOUR
Features:
■ Very high torsional flexibility with a linear torsional deflection characteristic
■ High torsional vibration and shock load absorbing capability
■ Backlash-free torque transmission
■ Ease of assembly thanks to the plug-in type design with ample axial float
■ Compensation of major misalignments
■ Torque limitation protecting the drive against overload
Coupling is a highly flexible flywheel design with an axial plug-in facility. It
NOTE: Photo includes taper-lock bushing.
Bushing is sold separately. provides a torsionally soft connection between an internal combustion engine and
the pump.
The highly flexible torque transmission characteristic is achieved by a disc-
shaped rubber element that is subjected to a torsional load and enables both,
the absorption of high torsional vibrations and the compensation of major
misalignments.
The inside diameter of the rubber disc element is vulcanized directly to a taper
hub. The toothed profile on the circumference of the element provides in service a
virtually backlash-free, positive plug-in connection to the coupling flange.
Ordering Information
Coupling Taper Bushing
Clutch Size Order Number FE Model Number SAE Bracket Size
required (sold separately)
8” 106128101 8” Flywheel Coupling R (SAE 5) 5 2517
10” 106129101 10” Flywheel Coupling R (SAE 4) 4 2517
11.5” 106130101 11.5” Flywheel Coupling R (SAE 3) 3 2517
14” 106131101 14” Flywheel Coupling R (SAE 1) 1 3535
Ordering Information
Order Taper-Lock
Bore Size FE Model Number Application
Number Size
1-7/8” x 1/2” key 106132101 Coupling Bushing 1-7/8” x1/2” 2517 SAE3, SAE4, SAE5
2-1/2” x 5/8” key 106133101 Coupling Bushing 2-1/2” x5/8” 2517 SAE3, SAE4, SAE5
3535 Size 1-7/8” x 1/2” key 106134101 Coupling Bushing 1-7/8” x1/2” 3535 SAE1
2-1/2” x 5/8” key 106135101 Coupling Bushing 2-1/2” x5/8” 3535 SAE1
Fig. 1 Fig. 2
Flywheel Couplings
Standard Centrifugal Pumps- SAE Engine Drive
Table 1
M A1
Coupling Size AC-T2,6 AC-T3 AC-T5
Tightening Nm 49 115
Torque MA2 lb-in 434 1020
Table 2
Tightening torques for the bolted flange connection to the engine flywheel.
SAE flywheel flange 8 10 11-1/2 14
Tightening Nm 42 102
Torque MA1 lb in 372 903
Fig. 6
FEET
30 70
20
BEST EFFICIENCY RANGE ■ Lightweight design.
60
25
15 50
20
S45A
40
15
10
30
S4A
10
S35A
20
S3A
5 S2A
5
10
1 2 3 4 5 6 7 8 9 10 11 12 13 LPS
3
2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 42 44 46 M PH
Ordering Information
"A" SERIES THERMOPLASTIC CENTRIFUGAL PUMPS
Suction x Pump Unit
Series Model HP Voltage
Discharge Order No. Wt.
S2A 2 115/230 94216151 27
S3A 3 230 94216191 29
A 2" x 2" MNPT S35A 3-1/2 230 94216201 31
S4A 4 230 94216301 35
S45A 4-1/2 230 94216401 39
Fittings kit contains (2) 2" slip x threaded connection union halves 31150109 2
Note: Set of union halves must be purchased separately.
40
S2KM
■ UL and CSA agency listing do not apply to any application
30 other than water applications.
S15KM
10 S1KM
20 S7KM
10
0 10 20 30 40 50 60 70 80 90
CAPACITY - GALLONS PER MINUTE
Ordering Information
"S" SERIES THERMOPLASTIC CENTRIFUGAL PUMPS
Pump Unit
Series Suction x Discharge Model HP Voltage
Order No. Wt.
S7KM 3/4 115 94028263 22
1-1/2” x 1-1/2” S1KM 1 115 94028271 24
S MNPT S15KM 1-1/2 115 94028289 26
S2M 2 115/230 94028297 35
Fittings kit contains (2) 1-1/2” slip x threaded connection union halves 31175608 1
Note: Set of union halves must be purchased separately.
Features:
■ 100% self-draining case satisfies both UL and IAPMO
standards.
■ Air-cooled heat sink allows pump to run dry without damage
to the shaft seal.
■ Floating eye seal between the closed impeller and the pump
case maximizes pump efficiency for best flow and pressure.
■ Accepts a 1-1/2” standard union. Union adapter kits must be
ordered separately.
■ UL and CSA Agency listings do not apply to any application
other than water applications.
METERS
FEET
PSI
60
25
50
15
20
40
15
10
30
S2JCM
S15JCM
10
20 S1JCM
S7JCM
5
5
10
0 10 20 30 40 50 60 70 80 90 GPM
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 M3PH
5-3/4”
6-1/4”
Dimensions (In Inches)
1-3/4”
HP A
7-1/2”
3/4 16-5/8”
1 16-5/8”
1-1/2 17-1/16”
2 17-1/16”
3” 8-7/8” 4”
A
Centrifugal Pumps
JCM Series
Self-Draining Non-Corrosive Centrifugal Pumps
Ordering Information
JCM Series with Straight Union Fit - Single Speed
Model No. Order No. HP Voltage Full Load Amps Svc. Factor Weight
S7JCM 94215696 3/4 115 9.8 1 22
S1JCM 94215704 1 115 9.8 1 24
S15JCM 94216587 1-1/2 115 12.4 1 26
S2JCM 94215522 2 115/230 16.8 1 35
JCM Series with Straight Union Fit - Single Speed with Built-In Air Switch & 3’ Cord with Standard 3 Prong Plug
Model No. Order No. HP Voltage Full Load Amps Svc. Factor Weight
S7JCM-A3 94216405 3/4 115 10.5 1 22
S1JCM-A3 94216421 1 115 10.5 1 24
S15JCM-A3 94216603 1-1/2 115 12.4 1 26
S2JCM-A3 94216447 2 115/230 16.0 1 35
Replacement Motors
JM Frame Centrifugal
Replacement Motors
HC-Series - ODP
Replacement Motors
HC-Series - TEFC
Shaft 10-3001-801
o
.03 x 45 .03 x 45
o
+.000
ø1.3745
1.3750
1.750
ø1.748
+.000
ø8.500 -.005
1.112 -.015
63 A
63 63
.245
.250
ø1.2490
1.2495
R. R. 1/2 UNC-2B TAP
03 03 1.5 DEEP
0 0
2.375
2.50 .001
5.875 KEYWAY .005 A
8.125
.25
Shaft 10-3003-801
o
.03 x 45 .03 x 45
o
+.000
ø1.3745
1.3750
1.750
ø1.748
+.000
ø12.500 -.005
1.112 -.015
63 A
63 63
.245
.250
ø1.2490
1.2495
8.125
.25
Centrifugal Pumps
Replacement Motors
HC-Series
Shaft 10-3004-801
+.0032
ø2.5025 -.0000
o
NOTE: Blend 45 TO R .09
ø2.302 .030 x 45o
+.002
ø.500 -.000
+.000
ø12.500 -.005
63 A
63
2.2496
Ø2.2491
45
+.000
o
3.06
KEYWAY ø1.972 -.015
63
5.44 3/4-10 UNC-2B x 1.63
R.
.001
.005 A
8.70
.25
Shaft 10-3009-801
+.0032
ø2.5025 -.0000
+.002
ø.500 -.000
+.000
ø16.000 -.005
63 A
63
2.2496
Ø2.2491
45
+.000
o
3.06
KEYWAY ø1.972 -.015
63
5.44 3/4-10 UNC-2B x 1.63
R.
.001
.005 A
8.70
.25
C X DD1
Y
Mi8370
ROTATION
DD3
Z
WARNING
7.5” Diameter Series
DA
D
DD2
AB
F BA
HØ E E
B
A
20 3600 4 3 254JP 11.25 9.5 17.93 6.25 5 8.25 0.53 28.93 7 3 5 5.81 5.31 8.75 8.93 5 12
25 3600 4 3 256JP 11.25 11.25 17.93 6.25 5 10 0.53 28.93 7 3 5 5.81 5.31 8.75 8.93 5 12
30 3600 4 3 284JP 11.25 10.75 19.81 6.25 5 9.5 0.53 30.81 7 3 5 5.81 5.31 8.75 12.21 5 13.96
15 3600 4 4 215JP 9.5 8 15.56 5.25 4.25 7 0.41 26.72 8 3 5.5 6.09 5.53 10 7.46 4.5 10.03
20 3600 4 4 254JP 11.25 9.5 17.93 6.25 5 8.25 0.53 29.09 8 3 5.5 6.09 5.53 10 8.93 5 12
25 3600 4 4 256JP 11.25 11.25 17.93 6.25 5 10 0.53 29.09 8 3 5.5 6.09 5.53 10 8.93 5 12
HC 4X4-75
30 3600 4 4 284JP 12.25 10.75 19.81 7 5.5 9.5 0.53 30.97 8 3 5.5 6.09 5.53 10 12.21 5 13.96
40 3600 4 4 286JP 12.25 12.25 19.81 7 5.5 11 0.53 30.97 8 3 5.5 6.09 5.53 10 12.21 5 13.96
50 3600 4 4 324JP 14.25 13.75 21.19 8 6.25 10.5 0.66 32.35 8 3 5.5 6.09 5.53 10 12.21 5.5 14.59
25 3600 5 4 256JP 11.25 11.25 17.93 6.25 5 10 0.53 29.52 8 3 5.5 6.5 5.91 10 8.93 5 12
30 3600 5 4 284JP 12.25 10.75 19.81 7 5.5 9.5 0.53 31.4 8 3.25 5.5 6.5 5.91 10 12.21 5 13.96
PAGE: CP-1300
HC 5X4-75 40 3600 5 4 286JP 12.25 12.25 19.81 7 5.5 11 0.53 31.4 8 3.25 5.5 6.5 5.91 10 12.21 5 13.96
50 3600 5 4 324JP 15.25 13.75 21.19 8 6.25 10.5 0.66 32.78 8 3.25 5.5 6.5 5.91 10 12.21 5.5 14.59
Centrifugal Pumps
60 3600 5 4 326* 14.25 13.75 21.19 8 6.25 12 0.66 32.78 8 3.25 5.5 6.5 5.91 10 13.22 5.5 15.59
Note: Dimensions are for estimating purposes only. Certified dimension drawings are available on request.
CP
C Y
X DD1
Mi8371
ROTATION
DD3
Z
WARNING
DA
10” Diameter Series
D
DD2
F BA
HØ
B
AB
E E
A
HC 6x4-10 60 3600 6 4 326* 14.25 13.75 21.19 8 6.25 12 0.66 33.6 9.5 4.25 6.5 7.38 6.84 11 13.22 5.5 15.59
75 3600 6 4 364* 15.75 14 22.31 9 7 11.25 0.66 34.72 9.5 4.25 6.5 7.38 6.84 11 13.22 6.12 16.59
100 3600 6 4 365* 15.75 14 23.31 9 7 12.25 0.66 35.72 9.5 4.25 6.5 7.38 6.84 11 13.22 6.12 16.59
125 3600 6 4 404* 18.5 16.62 27.84 10 8 12.25 0.81 40.25 9.5 4.25 6.5 7.38 6.84 11 16.39 6.88 18.41
5 1200 8 6 213JP 9.5 8 13.94 5.25 4.25 7 0.41 30.82 10 2.75 8.25 11 8.85 13.75 7.46 4.25 10.03
7.5 1200 8 6 254JP 11.25 9.5 15.81 6.25 5 8.25 0.53 32.69 10 2.75 8.25 11 8.85 13.75 7.93 4.75 11.03
10 1200 8 6 256JP 11.25 11.25 19.43 6.25 5 10 0.53 36.31 10 2.75 8.25 11 8.85 13.75 9.49 4.75 12
HC 8x6-10
20 1800 8 6 256JP 11.25 11.25 18.32 6.25 5 10 0.53 35.2 10 2.75 8.25 11 8.85 13.75 8.93 5 12
30 1800 8 6 286JP 12.25 12.25 21.31 7 5.5 11 0.53 38.19 10 2.75 8.25 11 8.85 13.75 12.21 5 13.96
40 1800 8 6 324JP 14.25 13.75 21.19 8 6.25 10.5 0.53 38.07 10 2.75 8.25 11 8.85 13.75 12.21 5.5 14.59
5 1200 8 6 213JP 9.5 8 13.94 5.25 4.25 7 0.41 30.82 10 2.75 8.25 11 8.85 13.75 7.46 4.25 10.03
7.5 1200 8 6 254JP 11.25 9.5 15.81 6.25 5 8.25 0.53 32.69 10 2.75 8.25 11 8.85 13.75 7.93 4.75 11.03
PAGE: CP-1305
HC 8x6-95 15 1800 8 6 254JP 11.25 9.5 15.81 6.25 5 8.25 0.53 32.69 10 2.75 8.25 11 8.85 13.75 8.93 5 12
20 1800 8 6 256JP 11.25 11.25 18.32 6.25 5 10 0.53 35.2 10 2.75 8.25 11 8.85 13.75 8.93 5 12
Centrifugal Pumps
25 1800 8 6 284JP 12.25 10.75 19.81 7 5.5 9.5 0.53 36.69 10 2.75 8.25 11 8.85 13.75 12.21 5 13.96
Note: Dimensions are for estimating purposes only. Certified dimension drawings are available on request.
CP AB
Mi8372
Y X
C DD1
ROTATION
DD3
Z
WARNING
14” Diameter Series
DA
D
DD2
F BA
B HØ
E E
A
30 1200 8 6 326* 14.25 13.75 22.19 8 6.25 12 0.66 36.66 9.56 6.38 4.81 13.37 12 7.22 12.21 5.5 14.59
40 1200 8 6 364* 15.75 14 22.31 9 7 11.25 0.66 36.78 9.56 6.38 4.81 13.37 12 7.22 13.2 6.12 16.59
HC 8x6-14
75 1800 8 6 365* 15.75 14 24.31 9 7 12.25 0.66 38.78 9.56 6.38 4.81 13.37 12 7.22 13.22 6.12 16.59
100 1800 8 6 404* 18.5 16.62 25.85 10 8 12.25 0.81 40.32 9.56 6.38 4.81 13.37 12 7.22 16.39 6.88 18.41
125 1800 8 6 444* 22 17 27.1 11 9 14.5 0.81 41.57 9.56 6.38 4.81 13.37 12 7.22 19.88 7.75 21.88
150 1800 8 6 445* 22 19 31.38 11 9 16.5 0.81 45.85 9.56 6.38 4.81 13.37 12 7.22 19.88 7.75 21.88
25 1200 10 10 324* 14.25 13.75 21.19 8 6.25 10.5 0.66 36.07 12 6.25 12 16.25 13.5 20 12.21 5.5 14.59
40 1200 10 10 364* 15.75 14 22.31 9 7 11.25 0.66 37.19 12 6.25 12 16.25 13.5 20 13.2 6.12 16.59
50 1200 10 10 365* 15.75 14 24.31 9 7 12.25 0.66 39.19 12 6.25 12 16.25 13.5 20 13.22 6.12 16.59
60 1200 10 10 404* 18.5 16.62 25.85 10 8 12.25 0.81 40.73 12 6.25 12 16.25 13.5 20 16.39 6.88 18.41
HC 10x10-14
100 1800 10 10 404* 18.5 16.62 25.85 10 8 12.25 0.81 40.73 12 6.25 12 16.25 13.5 20 16.39 6.88 18.41
PAGE: CP-1310
125 1800 10 10 405TCZ 22 17 27.1 11 9 14.5 0.81 41.98 12 6.25 12 16.25 13.5 20 19.88 7.75 21.88
150 1800 10 10 444TCZ 22 19 31.38 11 9 16.5 0.81 46.26 12 6.25 12 16.25 13.5 20 19.88 7.75 21.88
Centrifugal Pumps
200 1800 10 10 445TCZ 21.5 19.5 31.38 11 9 16.5 0.81 46.26 12 6.25 12 16.25 13.5 20 19.06 7.5 22.18
Note: Dimensions are for estimating purposes only. Certified dimension drawings are available on request.
Mi8373
FIGURE 1 FIGURE 2
X DD1
Y X DD1
ROTATION
DD3
DD3
Z
KEY
Z
KEY
U
U
DD2
DD2
D
G
N HØ
4 HOLES N
C
G
Y E HØ
E 4 HOLES
F
A
B E E
F
Q L B A
Q L
CP
All Series (7.5”, 10” & 14” Diameter)
CP
HC 3X2-10 1 3 2 13.25 7.375 7.00 5.75 5.375 .75 .6875 18.24 5.62 8.00 1.875 7.5 3 5.75 26.24 6.34 6.25 8.75 .50
HC 4X25-10 1 4 2.5 13.25 7.375 7.00 5.75 5.375 .75 .6875 18.27 5.62 8.00 1.875 8 3.03 7 26.26 6.78 6.47 9.5 .50
HC 4X3-10 1 4 3 13.25 7.375 7.00 5.75 5.375 .75 .6875 18.33 5.62 8.00 1.875 8.5 3.09 6.25 26.32 7.03 6.63 10 .50
Bearing Frame Dimensional Drawings
HC 6X4-10 1 6 4 13.25 7.375 7.00 5.75 5.375 .75 .6875 19.49 5.62 8.00 1.875 9.5 4.25 6.5 27.48 7.38 6.84 11 .50
HC 8X6-10 2 8 6 13.25 7.375 7.00 5.75 5.375 .75 .6875 17.99 5.62 8.00 1.875 10 2.75 8.25 32.14 11 8.85 13.75 .50
HC 8X6-95 2 8 6 13.25 7.375 7.00 5.75 5.375 .75 .6875 17.99 5.62 8.00 1.875 10 2.75 8.25 32.14 11 8.85 13.75 .50
HC 6X4-13 2 6 4 13.25 10.6875 7.00 5.75 8.6875 .75 .6875 21.24 5.62 8.00 2.5 11 6 8 35.49 9.38 8.88 12.5 .625
HC 5X3-14 2 5 3 13.25 10.6875 7.00 5.75 8.6875 .75 .6875 19.99 5.62 8.00 2.5 9.5 4.75 8.5 34.14 10 9.5 12.25 .625
HC 6X6-14 2 6 6 13.25 10.6875 7.00 5.75 8.6875 .75 .6875 20.43 5.62 8.00 2.5 10.5 5.19 9.5 34.58 12 11 15 .625
HC 8X6-14 2 8 6 13.25 10.6875 7.00 5.75 8.6875 .75 .6875 21.62 5.62 8.00 2.5 9.56 6.38 4.81 35.77 13.37 12 7.22 .625
HC 10X10-14 2 10 10 13.25 10.6875 7.00 5.75 8.6875 .75 .6875 21.49 5.62 8.00 2.5 12 6.25 12 35.64 16.25 13.5 20 .625
Note: Dimensions are for estimating purposes only. Certified dimension drawings are available on request.
PAGE: CP-1315
Centrifugal Pumps
X MP X
(DISCHARGE) ROTATION
C (DISCHARGE)
Z
Z
KEY
KEY
(SUCTION)
EØ
BØ
AØ
(SUCTION)
BØ
AØ
K
D
D
F
HØ
4 HOLES Y G HØ
4 HOLES G
F MP
J Y
CP
CP
All Models (10” & 14” Diameter)
HC 4x3-10 1 4 3 8.5 3.09 11.32 6.25 4 15 12 0.397 15.88 14.248 0.6875 11.38 7.00 24.4 1.875 11.5 .50
HC 4x3-10 1 4 3 8.5 3.09 11.32 6.25 5 13.12 8 0.397 14 12.373 0.6875 10.83 7.00 23.85 1.875 11.5 .50
HC 6x4-10 1 6 4 9.5 4.25 12.48 6.5 3 16.875 12 0.397 17.75 16.123 0.6875 10.83 7.00 25.01 1.875 11.5 .50
HC 6x4-10 1 6 4 9.5 4.25 12.48 6.5 4 15 12 0.397 15.88 14.248 0.6875 11.38 7.00 25.56 1.875 11.5 .50
HC 6x4-10 1 6 4 9.5 4.25 12.48 6.5 5 13.12 8 0.397 14 12.373 0.6875 10.83 7.00 25.01 1.875 11.5 .50
HC 8x6-10 2 8 6 10 2.75 10.98 8.25 1 20.875 12 0.469 21.75 20.125 0.6875 10.83 7.00 29.05 1.875 11.5 .50
HC 8x6-10 2 8 6 10 2.75 10.98 8.25 3 16.875 12 0.397 17.75 16.123 0.6875 10.83 7.00 29.05 1.875 11.5 .50
HC 8x6-10 2 8 6 10 2.75 10.98 8.25 4 15 12 0.397 15.88 14.248 0.6875 11.38 7.00 29.6 1.875 11.5 .50
HC 8x6-95 2 8 6 10 2.75 10.98 8.25 1 20.875 12 0.469 21.75 21.125 0.6875 10.83 7.00 29.05 1.875 11.5 .50
HC 8x6-95 2 8 6 10 2.75 10.98 8.25 3 16.875 12 0.397 17.75 16.123 0.6875 10.83 7.00 29.05 1.875 11.5 .50
HC 8x6-95 2 8 6 10 2.75 10.98 8.25 4 15 12 0.397 15.88 14.248 0.6875 11.38 7.00 29.6 1.875 11.5 .50
HC 6x4-13 2 6 4 11 6 14.23 8 1 20.875 12 0.469 21.75 20.125 0.6875 10.83 7.00 32.85 2.5 11.5 .625
HC 6x4-13 2 6 4 11 6 14.23 8 3 16.875 12 0.397 17.75 16.123 0.6875 10.83 7.00 32.85 2.5 11.5 .625
HC 6x4-13 2 6 4 11 6 14.23 8 4 15 12 0.397 15.88 14.248 0.6875 11.38 7.00 33.4 2.5 11.5 .625
HC 5x3-14 2 5 3 9.5 4.75 12.98 8.5 1 20.875 12 0.469 21.75 20.125 0.6875 10.83 7.00 31.6 2.5 11.5 .625
HC 5x3-14 2 5 3 9.5 4.75 12.98 8.5 3 16.875 12 0.397 17.75 16.123 0.6875 10.83 7.00 31.6 2.5 11.5 .625
HC 5x3-14 2 5 3 9.5 4.75 12.98 8..5 4 15 12 0.397 15.88 14.248 0.6875 11.38 7.00 32.15 2.5 11.5 .625
HC 6x6-14 2 6 6 10.5 5.19 13.42 9.5 1 20.875 12 0.469 21.75 20.125 0.6875 10.83 7.00 31.16 2.5 11.5 .625
HC 6x6-14 2 6 6 10.5 5.19 13.42 9.5 3 16.875 12 0.397 17.75 16.123 0.6875 10.83 7.00 31.16 2.5 11.5 .625
HC 6x6-14 2 6 6 10.5 5.19 13.42 9.5 4 15 12 0.397 15.88 14.248 0.6875 11.38 7.00 31.71 2.5 11.5 .625
HC 8x6-14 2 8 6 9.56 6.38 14.61 4.81 1 20.875 12 0.469 21.75 20.125 0.6875 10.83 7.00 32.36 2.5 11.5 .625
HC 8x6-14 2 8 6 9.56 6.38 14.61 4.81 3 16.875 12 0.397 17.75 16.123 0.6875 10.83 7.00 32.36 2.5 11.5 .625
HC 8x6-14 2 8 6 9.56 6.38 14.61 4.81 4 15 12 0.397 15.88 14.248 0.6875 11.38 7.00 32.91 2.5 11.5 .625
PAGE: CP-1320
HC 10x10-14 2 10 10 12 6.25 14.48 12 1 20.875 12 0.469 21.75 20.125 0.6875 10.83 7.00 32.23 2.5 11.5 .625
HC 10x10-14 2 10 10 12 6.25 14.48 12 3 16.875 12 0.397 17.75 16.123 0.6875 10.83 7.00 32.23 2.5 11.5 .625
Centrifugal Pumps
HC 10x10-14 2 10 10 12 6.25 14.48 12 4 15 12 0.397 15.88 14.248 0.6875 11.38 7.00 32.78 2.5 11.5 .625
Note: Dimensions are for estimating purposes only. Certified dimension drawings are available on request.
Centrifugal Pumps
Features:
■ Easy access packing area*
■ 2 piece stainless packing gland*
■ Fits industry standard JP motors
■ Hydraulically balanced impellers
■ Volute flow splitter in high capacity models
Model Number Explanation ■ Stainless impeller standard on most models
Example: 15XS4313-CCMLBD
■ Ease of service features include jack-out holes
15 = 15 Horsepower (CC only) and lifting bosses
XS = Centrifugal Series
■ Easy retro-fit industry standard suction, discharge and
4 = Suction Size
mounting bracket
3 = Discharge Size
13 = Nominal Impeller Dia. * Applicable to packing seal models only.
CC = Close Coupled
M = Shaft Sealing:
P=Packing
M=Mechanical Seal
LBD = Impeller Diameter (Alpha)
A=0 F=5 L=10
B=1 G=6 M=11
C=2 H=7 N=12
D=3 J=8 P=13
E=4 K=9 Q=14
Ordering Information
13” Nominal Impeller Diameter - (CC) Close Coupled w/Electric Motor
Suction/ Motor Impeller Motor Shaft Model Order
Pump Model Disch. Size HP RPM Frame Weight
Trim Enclosure Sealing Description Number
10 1750 215JP 9-3/8 ODP Packing 10XS32513-CCPKDJ 70032513100 390
10 1750 215JP 9-7/8 ODP Packing 10XS32513-CCPKJJ 70032513102 390
15 1750 254JP 11-3/8 ODP Packing 15XS32513-CCPMDJ 70032513110 483
15 1750 254JP 11-7/8 ODP Packing 15XS32513-CCPMJJ 70032513112 483
20 1750 256JP 12-3/4 ODP Packing 20XS32513-CCPNHF 70032513120 533
20 1750 256JP 13-1/16 ODP Packing 20XS32513-CCPPAG 70032513122 533
XS-3x25-13 3” x 2.5”
10 1750 215JP 9-3/8 ODP Mech Seal 10XS32513-CCMKDJ 71032513101 390
10 1750 215JP 9-7/8 ODP Mech Seal 10XS32513-CCMKJJ 71032513103 390
15 1750 254JP 11-3/8 ODP Mech Seal 15XS32513-CCMMDJ 71032513111 483
15 1750 254JP 11-7/8 ODP Mech Seal 15XS32513-CCMMJJ 71032513113 483
20 1750 256JP 12-3/4 ODP Mech Seal 20XS32513-CCMNHF 71032513121 533
20 1750 256JP 13-1/16 ODP Mech Seal 20XS32513-CCMPAG 71032513123 533
NOTES: There will be an impeller trimming charge applied for any non-standard impeller trim.
Consult price sheets for list price adders.
Centrifugal Pumps
XS Series
Standard Centrifugal Pumps - Close Coupled
Ordering Information
13” Nominal Impeller Diameter - (CC) Close Coupled w/Electric Motor
Suction/ Motor Impeller Motor Shaft Model Order
Pump Model HP RPM Frame Weight
Disch. Size Trim Enclosure Sealing Description Number
7.5 1750 213JP 8 ODP Packing 7XS4313-CCPJAA 70040313102 402
10 1750 215JP 9-1/8 ODP Packing 10XS4313-CCPKBD 70040313100 415
15 1750 254JP 10-3/4 ODP Packing 15XS4313-CCPLHF 70040313110 508
20 1750 256JP 11-3/4 ODP Packing 20XS4313-CCPMHF 70040313120 558
25 1750 284JP 12-5/16 ODP Packing 25XS4313-CCPNBD 70040313130 585
30 1750 286JP 12-3/4 ODP Packing 30XS4313-CCPNHF 70040313140 597
40 1750 324JP 13-1/6 ODP Packing 40XS4313-CCPPAG 70040313150 730
XS-4x3-13 4” x 3”
7.5 1750 213JP 8 ODP Mech Seal 7XS4313-CCMJAA 71040313103 402
10 1750 215JP 9-1/8 ODP Mech Seal 10XS4313-CCMKBD 71040313101 415
15 1750 254JP 10-3/4 ODP Mech Seal 15XS4313-CCMLHF 71040313111 508
20 1750 256JP 11-3/4 ODP Mech Seal 20XS4313-CCMMHF 71040313121 558
25 1750 284JP 12-5/16 ODP Mech Seal 25XS4313-CCMNDB 71040313131 585
30 1750 286JP 12-3/4 ODP Mech Seal 30XS4313-CCMNHF 71040313141 597
40 1750 324JP 13-1/6 ODP Mech Seal 40XS4313-CCMPAG 71040313151 730
20 1750 256JP 9-3/8 ODP Packing 20XS6413-CCPKDJ 70060413100 573
25 1750 284JP 10-1/4 ODP Packing 25XS6413-CCPLCF 70060413110 600
30 1750 286JP 10-7/8 ODP Packing 30XS6413-CCPLJJ 70060413120 612
30 1750 286JP 11-3/8 ODP Packing 30XS6413-CCPMDJ 70060413122 612
40 1750 324JP 12-1/4 ODP Packing 40XS6413-CCPNCF 70060413130 745
50 1750 326JP 12-7/8 ODP Packing 50XS6413-CCPNJJ 70060413140 878
XS-6x4-13 6” x 4”
20 1750 256JP 9-3/8 ODP Mech Seal 20XS6413-CCMKDJ 71060413101 573
25 1750 284JP 10-1/4 ODP Mech Seal 25XS6413-CCMLCF 71060413111 600
30 1750 286JP 10-7/8 ODP Mech Seal 30XS6413-CCMLJJ 71060413121 612
30 1750 286JP 11-3/8 ODP Mech Seal 30XS6413-CCMMDJ 71060413123 612
40 1750 324JP 12-1/4 ODP Mech Seal 40XS6413-CCMNCF 71060413131 745
50 1750 326JP 12-7/8 ODP Mech Seal 50XS6413-CCMNJJ 71060413141 878
25 1750 284JP 9-1/2 ODP Packing 25XS8613-CCPKFA 70080613150 685
30 1750 286JP 10 ODP Packing 30XS8613-CCPLAA 70080613100 697
40 1750 324JP 10-7/8 ODP Packing 40XS8613-CCPLJJ 70080613110 830
40 1750 324JP 11-1/8 ODP Packing 40XS8613-CCPMBD 70080613112 830
50 1750 326JP 11-5/8 ODP Packing 50XS8613-CCPMGD 70080613120 963
60 1750 364TCZ 11-7/8 ODP Packing 60XS8613-CCPMJJ 70080613130 1109
60 1750 364TCZ 12-5/16 ODP Packing 60XS8613-CCPNBD 70080613132 1109
75 1750 365TCZ 12-1/2 ODP Packing 75XS8613-CCPNFA 70080613140 1183
75 1750 365TCZ 13 ODP Packing 75XS8613-CCMPAA 70080613142 1183
XS-8x6-13 8” x 6”
25 1750 284JP 9-1/2 ODP Mech Seal 25XS8613-CCMKFA 71080613151 685
30 1750 286JP 10 ODP Mech Seal 30XS8613-CCMLAA 71080613101 697
40 1750 324JP 10-7/8 ODP Mech Seal 40XS8613-CCMLJJ 71080613111 830
40 1750 324JP 11-1/8 ODP Mech Seal 40XS8613-CCMMBD 71080613113 830
50 1750 326JP 11-5/8 ODP Mech Seal 50XS8613-CCMMGD 71080613121 963
60 1750 364TCZ 11-7/8 ODP Mech Seal 60XS8613-CCMMJJ 71080613131 1109
60 1750 364TCZ 12-5/16 ODP Mech Seal 60XS8613-CCMNDB 71080613133 1109
75 1750 365TCZ 12-1/2 ODP Mech Seal 75XS8613-CCMNFA 71080613141 1183
75 1750 365TCZ 13 ODP Mech Seal 75XS8613-CCMPAA 71080613143 1183
60 1750 364TCZ 9-13/16 ODP Packing 60XS10813-CCPKJB 70100813100 1294
75 1750 365TCZ 10-7/8 ODP Packing 75XS10813-CCPLJJ 70100813110 1368
75 1750 365TCZ 11-1/4 ODP Packing 75XS10813-CCPLCF 70100813112 1368
100 1750 404TCZ 11-15/16 ODP Packing 100XS10813-CCPMKE 70100813120 1565
100 1750 404TCZ 12-3/8 ODP Packing 100XS10813-CCPNDJ 70100813122 1565
125 1750 444TCZ 12-3/4 ODP Packing 125XS10813-CCPNHF 70100813130 1888
150 1750 445TCZ 13 ODP Packing 150XS10813-CCPPAA 70100813140 1981
XS-10x8-13 10” x 8”
60 1750 364TCZ 9-13/16 ODP Mech Seal 60XS10813-CCMKJB 71100813101 1294
75 1750 365TCZ 10-7/8 ODP Mech Seal 75XS10813-CCMLJJ 71100813111 1368
75 1750 365TCZ 11-1/4 ODP Mech Seal 75XS10813-CCMLCF 71100813113 1368
100 1750 404TCZ 11-15/16 ODP Mech Seal 100XS10813-CCMMKE 71100813121 1565
100 1750 404TCZ 12-3/8 ODP Mech Seal 100XS10813-CCMNDJ 71100813123 1565
125 1750 444TCZ 12-3/4 ODP Mech Seal 125XS10813-CCMNHF 71100813131 1888
150 1750 445TCZ 13 ODP Mech Seal 150XS10813-CCMPAA 71100813141 1981
NOTES: There will be an impeller trimming charge applied for any non-standard impeller trim.
Consult price sheets for list price adders.
Model XS-3x25-13
30
NPSHr - FEET
60 20
200 13.062 in
50 55 10
55 12.75 in 60
180 63 0
50 65
11.875 in
160
45 65.9
11.375 in
TOTAL HEAD - METERS
140 65
40
63
35 120
9.875 in
60
30 9.375 in
100 55
50 55
25
50
80
7.5 hp
20
40
60 55
15
50
40 40
10
10 hp 20 hp SIZE: 3” x 2.5”
15 hp IMPELLER DIA: Various
5 SPEED: 1750 RPM
20
0 50 100 150 200 250 300 350 400 450 500 550
XS Series
Standard Centrifugal Pumps - Close Coupled
Model XS-4x3-13
20
NPSHr - FEET
15
200
10
60
13.062 in 60 5
180 70
12.75 in 0
75
12.312 in 78
160
50 78.5
11.75 in 78
75
TOTAL HEAD - METERS
140
TOTAL HEAD - FEET
40 70
120
10.75 in
60
100
30 9.125 in
50
80
40 hp
8 in
20 60
60
30 hp
5 hp
40 25 hp
60
10
20 hp
50
20
15 hp
10 hp SIZE: 4” x 3”
7.5 hp IMPELLER DIA: Various
0 0 SPEED: 1750 RPM
0 100 200 300 400 500 600 700 800 900 1000
10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170 180 190 200 210 220 230
Model XS-6x4-13
30
NPSHr - FEET
20
55 12.875 in
180
76 10
80
50 12.25 in 82
0
160 83.5
45
82
11.375 in 80
140
40
TOTAL HEAD - METERS
10.875 in 76
35 120
10.25 in 72
30
100
9.375 in
68
76 80 82
25
84
80
10 hp 84
82
20 80
15 hp 50 hp
60 76 40 hp
15 72
68 30 hp
40
10 25 hp
20 hp
SIZE: 6” x 4”
IMPELLER DIA: Various
5 20 SPEED: 1750 RPM
0 100 200 300 400 500 600 700 800 900 1000 1100 1200 1300 1400 1500
FLOWRATE U.S. GALLONS PER MINUTE
20 40 60 80 100 120 140 160 180 200 220 240 260 280 300 320 340
FLOWRATE CUBIC METERS PER HOUR
Centrifugal Pumps
XS Series
Standard Centrifugal Pumps - Close Coupled
Model XS-8x6-13
15
NPSHr - FEET
10
55
13 in 60 70
74 5
78
175
82
12.5 in 0
50 84
12.312 in
85
85.9
45 150 11.875 in
TOTAL HEAD - METERS
11.625 in 85
84
40
11.125 in
125
82
10.875 in
35
75 hp
10 in
30 100
9.5 in 60 hp
78
25 60
70 50 hp
75 74
40 hp
20
25 hp
SIZE: 8” x 6”
30 hp
IMPELLER DIA: Various
15 50 SPEED: 1780 RPM
200 400 600 800 1000 1200 1400 1600 1800 2000 2200
25 50 75 100 125 150 175 200 225 250 275 300 325 350 375 400 425 450 475 500 525
Model XS-10x8-13
30
NPSHr - FEET
20
55
180
10
13 in 60
72
50 0
160 80
12.75 in
85
45 12.375 in
TOTAL HEAD - METERS
140
TOTAL HEAD - FEET
86 86.3
86
40 11.9375 in
85
120
35
11.25 in
125 hp 80
100
10.875 in 150 hp
30
80
9.8125 in
25
100 hp
60
50 hp
60
20 75 hp
72
40 60 hp
15
SIZE: 10” x 8”
IMPELLER DIA: Various
10 SPEED: 1780 RPM
20
500 1000 1500 2000 2500 3000 3500 4000 4500 5000
50 100 150 200 250 300 350 400 450 500 550 600 650 700 750 800 850 900 950 1000 1050 1100 1150
FLOWRATE CUBIC METERS PER HOUR
XS Series
Standard Centrifugal Pumps - Bearing Frame
Ordering Information
9” Nominal Impeller Diameter - (BF) Bearing Frame
Suction/ Rotation Volute Impeller Model
Pump Model Shaft Seal Fit Order Number Weight
Disch. Size Design Material Description
CW NPT Packing Standard Cast Iron XS439-BFNP-CW 64040309100 135
CCW NPT Packing Standard Cast Iron XS439-BFNP-CCW 64040309200 135
CW Victaulic Packing Standard Cast Iron XS439-BFVP-CW 64040309101 135
CCW Victaulic Packing Standard Cast Iron XS439-BFVP-CCW 64040309201 135
XS-4x3-9 4” x 3”
CW NPT Mech Seal Standard Cast Iron XS439-BFNM-CW 65040309100 135
CCW NPT Mech Seal Standard Cast Iron XS439-BFNM-CCW 65040309200 135
CW Victaulic Mech Seal Standard Cast Iron XS439-BFVM-CW 65040309101 135
CCW Victaulic Mech Seal Standard Cast Iron XS439-BFVM-CCW 65040309201 135
CW Flange Packing Standard Cast Iron XS869-BFP 64080609102 235
XS-8x6-9 8” x 6”
CW Flange Mech Seal Standard Cast Iron XS869-BFM 65080609102 235
Model XS-4x3-9
3000 rpm
260
90
80
240
80
70 220
EFFICIENCY %
70
200
TOTAL HEAD - METERS
60
TOTAL HEAD - FEET
2500 rpm 60
180
50 160 50
140
40
40
120
30 100 60 hp
1750 rpm
80
50 hp
20 40 hp
7.5 hp 25 hp 30 hp
60 20 hp
10 hp SIZE: 4” x 3”
15 hp
IMPELLER DIA: 9”
40 SPEED: Various
10
0 100 200 300 400 500 600 700 800 900 1000 1100
XS Series
Standard Centrifugal Pumps - Bearing Frame
Model XS-8x6-9
27
2000 rpm 90
90
26
EFFICIENCY %
80
85
25
70
1900 rpm
24 80
TOTAL HEAD - METERS
60
23 50 hp
75
22
1800 rpm
70
21
20 65
30 hp
19
60
18 40 hp
55
17
SIZE: 8” x 6”
IMPELLER DIA: 9”
16 50 SPEED: Various
200 400 600 800 1000 1200 1400 1600 1800 2000
25 50 75 100 125 150 175 200 225 250 275 300 325 350 375 400 425 450 475
Model XS-3x25-13
40
NPSHr - FEET
30
120
400 20
110 10
2400 rpm
50
0
100 350 60
2200 rpm 63
90
300
65
TOTAL HEAD - METERS
80
2000 rpm
250
70 63
1800 rpm
60 60
200
50 1600 rpm
50 hp
150 50
60 50
40 63
65
40 hp
30
100 63
60
20 30 hp
50
50 25 hp
10 20 hp
15 hp SIZE: 3” x 2.5”
IMPELLER DIA: 13”
0 SPEED: Various
0
50 100 150 200 250 300 350 400 450 500 550 600
XS Series
Standard Centrifugal Pumps - Bearing Frame
Model XS-4x3-13
40
NPSHr - FEET
30
130
450 20
120 10
2600 rpm
60
400 70 0
110 75
75
90
TOTAL HEAD - FEET
20 40 60 80 100 120 140 160 180 200 220 240 260 280
FLOWRATE CUBIC METERS PER HOUR
Model XS-6x4-13
40
NPSHr - FEET
30
110
2400 rpm 20
350 60
10
100
78 82 0
82.9
90 300 2200 rpm
82
80 78
TOTAL HEAD - METERS
70 72
150 hp
60 200
1800 rpm
50 60
1600 rpm
150 60
78
40 82
25 hp 82
30 hp 78
30 100
72 125 hp
20 100 hp
60
50 75 hp
60 hp
10 50 hp
40 hp SIZE: 6” x 4”
IMPELLER DIA: 13”
0 SPEED: Various
0
0 200 400 600 800 1000 1200 1400 1600 1800 2000 2200
25 50 75 100 125 150 175 200 225 250 275 300 325 350 375 400 425 450 475 500
FLOWRATE CUBIC METERS PER HOUR
Centrifugal Pumps
XS Series
Standard Centrifugal Pumps - Bearing Frame
Model XS-8x6-13
30
NPSHr - FEET
20
130
400
60 70 10
2600 rpm 75
120 82
84 0
110 350 85
2400 rpm
84
100
TOTAL HEAD - METERS
300 82
TOTAL HEAD - FEET
90 2200 rpm
80 250
2000 rpm
70 200 hp
200
1800 rpm 175 hp
60
150 hp
50 100 150 200 250 300 350 400 450 500 550 600 650 700 750
FLOWRATE CUBIC METERS PER HOUR
Model XS-10x8-13
40
NPSHr - FEET
2400 rpm 30
60
300 70
90 20
80
10
275 85
0
80
2200 rpm 86
250
TOTAL HEAD - METERS
70
TOTAL HEAD - FEET
225
2000 rpm
60
200
150
40
1600 rpm 200 hp
60 70
125 80
85 175 hp
30 75 hp 86
100 85 150 hp
20 80 125 hp
75
100 hp SIZE: 10” x 8”
IMPELLER DIA: 13”
10 50 SPEED: Various
400 800 1200 1600 2000 2400 2800 3200 3600 4000 4400
FLOWRATE U.S. GALLONS PER MINUTE
50 100 150 200 250 300 350 400 450 500 550 600 650 700 750 800 850 900 950 1000 1050
FLOWRATE CUBIC METERS PER HOUR
XS Series
Standard Centrifugal Pumps - SAE Engine Drive
Ordering Information
9” Nominal Impeller Diameter - (SA) SAE Engine Drive
Suction/ Rotation Volute Impeller Model
Pump Model Shaft Seal Fit Order Number Weight
Disch. Size Design Material Description
CW NPT Packing 4/5 Cast Iron XS439-SA45NP 66040309145 150
CW Victaulic Packing 4/5 Cast Iron XS439-SA45VP 66040309245 150
CW NPT Packing 2/3 Cast Iron XS439-SA23NP 66040309123 150
CW Victaulic Packing 2/3 Cast Iron XS439-SA23VP 66040309223 150
XS-4x3-9 4” x 3”
CW NPT Mech Seal 4/5 Cast Iron XS439-SA45NM 67040309145 150
CW Victaulic Mech Seal 4/5 Cast Iron XS439-SA45VM 67040309245 150
CW NPT Mech Seal 2/3 Cast Iron XS439-SA23NM 67040309123 150
CW Victaulic Mech Seal 2/3 Cast Iron XS439-SA23VM 67040309223 150
CW Flange Packing 4/5 Cast Iron XS869-SA45P 66080609345 250
CW Flange Packing 2/3 Cast Iron XS869-SA23P 66080609323 250
XS-8x6-9 8” x 6”
CW Flange Mech Seal 4/5 Cast Iron XS869-SA45M 67080609345 250
CW Flange Mech Seal 2/3 Cast Iron XS869-SA23M 67080609323 250
Model XS-4x3-9
3000 rpm
260
90
80
240
80
70 220
EFFICIENCY %
70
200
TOTAL HEAD - METERS
60
TOTAL HEAD - FEET
2500 rpm 60
180
50 160 50
140
40
40
120
30 100 60 hp
1750 rpm
80
50 hp
20 40 hp
7.5 hp 25 hp 30 hp
60 20 hp
10 hp SIZE: 4” x 3”
15 hp
IMPELLER DIA: 9”
40 SPEED: Various
10
0 100 200 300 400 500 600 700 800 900 1000 1100
XS Series
Standard Centrifugal Pumps - SAE Engine Drive
Model XS-8x6-9
27
2000 rpm 90
90
26
EFFICIENCY %
80
85
25
70
1900 rpm
24 80
TOTAL HEAD - METERS
60
23 50 hp
75
22
1800 rpm
70
21
20 65
30 hp
19
60
18 40 hp
55
17
SIZE: 8” x 6”
IMPELLER DIA: 9”
16 50 SPEED: Various
200 400 600 800 1000 1200 1400 1600 1800 2000
25 50 75 100 125 150 175 200 225 250 275 300 325 350 375 400 425 450 475
Model XS-3x25-13
40
NPSHr - FEET
30
120
400 20
110 10
2400 rpm
50
0
100 350 60
2200 rpm 63
90
300
65
TOTAL HEAD - METERS
80
2000 rpm
250
70 63
1800 rpm
60 60
200
50 1600 rpm
50 hp
150 50
60 50
40 63
65
40 hp
30
100 63
60
20 30 hp
50
50 25 hp
10 20 hp
15 hp SIZE: 3” x 2.5”
IMPELLER DIA: 13”
0 SPEED: Various
0
50 100 150 200 250 300 350 400 450 500 550 600
XS Series
Standard Centrifugal Pumps - SAE Engine Drive
Model XS-4x3-13
40
NPSHr - FEET
30
130
450 20
120 10
2600 rpm
60
400 70 0
110 75
75
90
TOTAL HEAD - FEET
20 40 60 80 100 120 140 160 180 200 220 240 260 280
FLOWRATE CUBIC METERS PER HOUR
Model XS-6x4-13
40
NPSHr - FEET
30
110
2400 rpm 20
350 60
10
100
78 82 0
82.9
90 300 2200 rpm
82
80 78
TOTAL HEAD - METERS
70 72
150 hp
60 200
1800 rpm
50 60
1600 rpm
150 60
78
40 82
25 hp 82
30 hp 78
30 100
72 125 hp
20 100 hp
60
50 75 hp
60 hp
10 50 hp
40 hp SIZE: 6” x 4”
IMPELLER DIA: 13”
0 SPEED: Various
0
0 200 400 600 800 1000 1200 1400 1600 1800 2000 2200
25 50 75 100 125 150 175 200 225 250 275 300 325 350 375 400 425 450 475 500
FLOWRATE CUBIC METERS PER HOUR
Centrifugal Pumps
XS Series
Standard Centrifugal Pumps - SAE Engine Drive
Model XS-8x6-13
30
NPSHr - FEET
20
130
400
60 70 10
2600 rpm 75
120 82
84 0
110 350 85
2400 rpm
84
100
TOTAL HEAD - METERS
300 82
TOTAL HEAD - FEET
90 2200 rpm
80 250
2000 rpm
70 200 hp
200
1800 rpm 175 hp
60
150 hp
50 100 150 200 250 300 350 400 450 500 550 600 650 700 750
FLOWRATE CUBIC METERS PER HOUR
Model XS-10x8-13
40
NPSHr - FEET
2400 rpm 30
60
300 70
90 20
80
10
275 85
0
80
2200 rpm 86
250
TOTAL HEAD - METERS
70
TOTAL HEAD - FEET
225
2000 rpm
60
200
150
40
1600 rpm 200 hp
60 70
125 80
85 175 hp
30 75 hp 86
100 85 150 hp
20 80 125 hp
75
100 hp SIZE: 10” x 8”
IMPELLER DIA: 13”
10 50 SPEED: Various
400 800 1200 1600 2000 2400 2800 3200 3600 4000 4400
FLOWRATE U.S. GALLONS PER MINUTE
50 100 150 200 250 300 350 400 450 500 550 600 650 700 750 800 850 900 950 1000 1050
FLOWRATE CUBIC METERS PER HOUR
Features:
■ Heavy duty bearing frame
■ Rugged 2-3/8” Stressproof ® shaft
■ 1-1/4” double keyed impeller
■ Compact space saving design
■ Easy access packing area*
■ Easy retro-fit with industry standard suction, discharge
Model Number Explanation and mounting bracket
Example: XS869-HBFP-CW
■ Diverse application options:
XS = Centrifugal Series
8 = Suction Size ■ NPT & Victaulic volutes
6 = Discharge Size ■ CW & CCW rotations available
9 = Nominal Impeller Dia. ■ Available in both “B”(7/8” shaft) and “C”(1-1/4” shaft) fits
HB = Hydraulic
* Applicable to packing seal models only.
F = Connection
N=NPT
V=Victaulic
F=Flange
P = Shaft Sealing:
P=Packing
M=Mechanical Seal
CW = Rotation:
CW=Clockwise
Centrifugal Pumps
XS Series
Standard Centrifugal Pumps - Hydraulic Motor Drive
Ordering Information
9” Nominal Impeller Diameter - (HB) Hydraulic
Suction/ Rotation Volute Impeller Model
Pump Model Shaft Seal Fit Order Number Weight
Disch. Size Design Material Description
CW NPT Packing B Cast Iron XS439-HBNP-CW 68040309100 145
CCW NPT Packing B Cast Iron XS439-HBNP-CCW 68040309200 145
CW Victaulic Packing B Cast Iron XS439-HBVP-CW 68040309101 145
CCW Victaulic Packing B Cast Iron XS439-HBVP-CCW 68040309201 145
CW NPT Mech Seal B Cast Iron XS439-HBNM-CW 69040309100 145
CCW NPT Mech Seal B Cast Iron XS439-HBNM-CCW 69040309200 145
CW Victaulic Mech Seal B Cast Iron XS439-HBVM-CW 69040309101 145
CCW Victaulic Mech Seal B Cast Iron XS439-HBVM-CCW 69040309201 145
XS-4x3-9 4” x 3”
CW NPT Packing C Cast Iron XS439-HCNP-CW 68040309300 145
CCW NPT Packing C Cast Iron XS439-HCNP-CCW 68040309400 145
CW Victaulic Packing C Cast Iron XS439-HCVP-CW 68040309301 145
CCW Victaulic Packing C Cast Iron XS439-HCVP-CCW 68040309401 145
CW NPT Mech Seal C Cast Iron XS439-HCNM-CW 69040309300 145
CCW NPT Mech Seal C Cast Iron XS439-HCNM-CCW 69040309400 145
CW Victaulic Mech Seal C Cast Iron XS439-HCVM-CW 69040309301 145
CCW Victaulic Mech Seal C Cast Iron XS439-HCVM-CCW 69040309401 145
CW Flange Packing B Cast Iron XS869-SA45P 68080609102 245
CW Flange Mech Seal B Cast Iron XS869-SA23P 69080609102 245
XS-8x6-9 8” x 6”
CW Flange Packing C Cast Iron XS869-SA45M 68080609302 245
CW Flange Mech Seal C Cast Iron XS869-SA23M 69080609302 245
NOTES: There will be an impeller trimming charge applied for any non-standard impeller trim.
Consult price sheets for list price adders.
Model XS-4x3-9
3000 rpm
260
90
80
240
80
70 220
EFFICIENCY %
70
200
TOTAL HEAD - METERS
60
TOTAL HEAD - FEET
2500 rpm 60
180
50 160 50
140
40
40
120
30 100 60 hp
1750 rpm
80
50 hp
20 40 hp
7.5 hp 25 hp 30 hp
60 20 hp
10 hp SIZE: 4” x 3”
15 hp
IMPELLER DIA: 9”
40 SPEED: Various
10
0 100 200 300 400 500 600 700 800 900 1000 1100
XS Series
Standard Centrifugal Pumps - Hydraulic Motor Drive
Model XS-8x6-9
27
2000 rpm 90
90
26
EFFICIENCY %
80
85
25
70
1900 rpm
24 80
TOTAL HEAD - METERS
60
23 50 hp
75
22
1800 rpm
70
21
20 65
30 hp
19
60
18 40 hp
55
17
SIZE: 8” x 6”
IMPELLER DIA: 9”
16 50 SPEED: Various
200 400 600 800 1000 1200 1400 1600 1800 2000
25 50 75 100 125 150 175 200 225 250 275 300 325 350 375 400 425 450 475
11
5
1
7
12
2 16
8
10
9
19
17
6
18
12
13
15
14
6 2
9
5
14 9
#5 Impeller Kit
2
#6 Case Kit
3
4 5
8
12 13
11
#7
Base Kit
3 7
2
5
#3 Impeller Kit
9 11 6 1
12
14 13 4
5
8
14 13 12
3
2
17 15
9 11
7 10
5
8
14 13 12
3
2
17 15
9 11
7 10
Model DC1-1/2
Parts for Centrifugal Pumps
6
4
3
11
13 12
2
8 7
5
9-10
16
1
8
5
2 14
3
15 7 11
10
6 13
4 12
9
Model DC4
Parts for Centrifugal Pumps
6 1
17
11
3 4
10
14 13
2
5
15
16 8 7
9
6
11
10
12
4a
11
1 2 3 4 5 6 7 8
2
6
3 4 4
6 31
15 12 11
5
33
1
21
14 23 22
16
36
20
24
37
32
20
16
19 9 & 10
2,3 &4
35
22
26
25
24
11
13
5
20
36 (Module)
8
14 35
32
17
21 16
15
12
7 13
31
17 33
19 18 34
22
15
25
24 31
11 17
Repair Parts
10
5
6
3 8 9
8
7
1
2
3
5
6
8 7a
1
2
4
5
6
3
IMPORTANT
Every carrier used by Franklin Pump Systems, Inc. is required to verify and sign for the condition
of and the number of pieces that are released to them for delivery. Our control and responsibility
for any shipment ceases when the carrier signs the Bill of Lading. When you sign the Bill of
Lading, you legally assume responsibility of the shipment being delivered. Please, thoroughly
inspect each shipment immediately upon arrival.
If cartons, packages, or crates are received in short or damaged condition, it is important that
you notify the driver and insist on a notation of the loss or damage across the face of the freight
bill. Failure to do this could negate any opportunity you have to file a claim. Claims for short or
damaged material must be filed in writing with the carrier immediately after delivery.
If concealed loss or damage is discovered, notify the carrier at once and request an inspection.
It is also important that you do not discard the shipping carton or container. A concealed
damage report should be made within ten (10) days of delivery of the shipment. The carrier’s
agent will make an inspection and usually will grant a concealed damage notation. If you give
the carrier a clear receipt for the goods that have been damaged in transit, you do so at your
own risk and expense.
We are willing to assist you to collect claims for loss or damage, but we are not responsible for
collection of claims or replacement of material (shortage or damage) if not noted on the Bill of
Lading at the time of delivery.
Due to frequent damage of heavy UPS shipments, Franklin Pump Systems, Inc. does not ship
orders over 75 lbs. by UPS unless customer agrees to take full responsibility.
Mi8600
Warranty
PAGE: WR-105
DATE: June 5, 2006
Franklin Pump System’s warranty obligation with regard to equipment not of its own manufacture is limited to the
warranty actually extended to Franklin Pump System by its suppliers.
This warranty extends only to the original retail purchaser and only during the time in which the original retail
purchaser occupies the site where the product was originally installed.
Requests for service under this warranty shall be made by contacting the installing Franklin Pump System
dealer (point of purchase) as soon as possible after the discovery of any alleged defect. Franklin Pump System will
subsequently take corrective action as promptly as reasonably possible.
Franklin Pump System at its discretion may replace or repair any product that fails under this warranty after
inspection by an authorized company representative or after Franklin Pump System has received the product at our
factory. Replacement or repair cannot be made until after the product is inspected. All charges or expenses for freight
to and from the factory, removal and reinstallation of the product, or installation of a replacement product are the
responsibility of the purchaser.
THIS WARRANTY SUPERSEDES ANY WARRANTY NOT DATED OR BEARING AN EARLIER DATE. ANY
IMPLIED WARRANTIES WHICH THE PURCHASER MAY HAVE, INCLUDING MERCHANT ABILITY AND FITNESS
FOR A PARTICULAR PURPOSE, SHALL NOT EXTEND BEYOND THE APPLICABLE WARRANTY PERIOD. Some
states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply
to you. IN NO EVENT SHALL FRANKLIN PUMP SYSTEM BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL
DAMAGES. Some states do not allow the exclusion or limitation of incidental or consequential damages, so
the above may not apply to you.
This warranty does not apply to any product which has been subjected to negligence, alteration, accident, abuse,
misuse, improper installation, vandalism, civil disturbances, or acts of God. The only warranties authorized by Franklin
Pump System are those set forth herein. Franklin Pump System does not authorize other persons to extend any
warranties with respect to its products, nor will Franklin Pump System assume liability for any unauthorized warranties
made in connection with the sale of its products.
THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH
MAY VARY FROM STATE TO STATE.
* Contact Franklin Pump Systems, Inc. Export Division for International Warranty.