Beruflich Dokumente
Kultur Dokumente
KMF0609045CE
Personal Facsimile
KX-FT932FX-B
B : Black Version
(for Europe)
TABLE OF CONTENTS
PAGE PAGE
1 Safety Precautions -----------------------------------------------3 15.2. Gear Section--------------------------------------------- 131
1.1. For Service Technicians----------------------------------3 15.3. Jams ------------------------------------------------------- 137
1.2. AC Caution --------------------------------------------------4 15.4. Cleaning -------------------------------------------------- 138
1.3. Personal Safety Precautions----------------------------5 16 Miscellaneous -------------------------------------------------- 139
1.4. Service Precautions ---------------------------------------6 16.1. Terninal Guide of the ICs, Transistors and
2 Warning --------------------------------------------------------------7 Diodes ----------------------------------------------------- 139
2.1. About Lead Free Solder (PbF: Pb free) --------------7 16.2. How to Replace the Flat Package IC-------------- 141
2.2. Insulation Resistance Test -------------------------------7 16.3. Test Chart------------------------------------------------ 143
2.3. Battery Caution ---------------------------------------------7 17 Schematic Diagram ------------------------------------------- 146
2.4. Disposal Cautions------------------------------------------8 17.1. Digital Board --------------------------------------------- 146
3 Specifications ------------------------------------------------------ 9 17.2. Analog Board -------------------------------------------- 148
4 General/Introduction------------------------------------------- 10 17.3. Operation Board ---------------------------------------- 150
4.1. Optional Accessories------------------------------------ 10 17.4. Power Supply Board----------------------------------- 151
5 Features------------------------------------------------------------ 10 18 Printed Circuit Board----------------------------------------- 153
5.1. ---------------------------------------------------------------- 10 18.1. Digital Board --------------------------------------------- 153
6 Technical Descriptions---------------------------------------- 11 18.2. Analogue Board ---------------------------------------- 155
6.1. Connection Diagram ------------------------------------ 11 18.3. Operation Board ---------------------------------------- 157
6.2. General Block Diagram--------------------------------- 12 18.4. Power Supply Board----------------------------------- 159
6.3. Control Section ------------------------------------------- 14 19 Appendix Information of Schematic Diagram ------- 160
6.4. Facsimile Section ---------------------------------------- 20 20 Exploded View and Replacement Parts List --------- 161
6.5. Sensors and Switches ---------------------------------- 26 20.1. Cabinet, Mechanical and Electrical Parts
6.6. Modem Section ------------------------------------------- 30 Location --------------------------------------------------- 161
6.7. NCU Section ---------------------------------------------- 37 20.2. Replacement Parts List ------------------------------- 167
6.8. ITS (Integrated Telephone System) and 20.3. Cabinet and Mechaical Parts ------------------------ 167
Monitor Section ------------------------------------------- 41 20.4. Digital Board Parts ------------------------------------- 168
6.9. ATAS (Automatic Telephone Answering 20.5. Analog Board Parts ------------------------------------ 170
System) Section ------------------------------------------ 41 20.6. Operation Board Parts -------------------------------- 171
6.10. Operation Board Section------------------------------- 43 20.7. Power Supply Board Parts --------------------------- 172
6.11. LCD Section ----------------------------------------------- 44 20.8. Fixtures and Tools-------------------------------------- 173
6.12. Power Supply Board Section ------------------------- 45
7 Location of Controls and Components------------------ 48
7.1. Overview --------------------------------------------------- 48
7.2. Control Panel---------------------------------------------- 49
8 Installation Instructions -------------------------------------- 50
8.1. Installation Space ---------------------------------------- 50
8.2. Connections ----------------------------------------------- 50
8.3. Installing the Recording Paper------------------------ 51
9 Operation Instructions ---------------------------------------- 52
9.1. Setting Your Logo ---------------------------------------- 52
10 Test Mode---------------------------------------------------------- 54
10.1. DTMF Single Tone Transmit Selection ------------- 55
10.2. Button Code Table --------------------------------------- 55
10.3. Print Test Pattern----------------------------------------- 55
11 Service Mode ----------------------------------------------------- 56
11.1. Programming and Lists --------------------------------- 56
11.2. The Example of the Printed List ---------------------- 60
12 Troubleshooting Guide --------------------------------------- 64
12.1. Troubleshooting summary ----------------------------- 64
12.2. Error Messages-Display-------------------------------- 65
12.3. Error Messages Report--------------------------------- 66
12.4. Remote Programming ---------------------------------- 88
12.5. Troubleshooting Details -------------------------------- 91
13 Service Fixture & Tools --------------------------------------117
14 Disassembly and Assembly Instructions--------------118
14.1. Disassembly Flowchart --------------------------------118
14.2. Disassembly Procedurel ----------------------------- 120
15 Maintenance ---------------------------------------------------- 129
15.1. Maintenance Items and Componet Locations -- 129
2
KX-FT932FX-B
1 Safety Precaution
1. Before servicing, unplug the AC power cord to prevent an electric shock.
2. When replacing parts, use only the manufacturer's recommended components.
3. Check the condition of the power cord. Replace if wear or damage is evident.
4. After servicing, be sure to restore the lead dress, insulation barriers, insulation papers, shields, etc.
5. Before returning the serviced equipment to the customer, be sure to perform the following insulation resistance test to prevent
the customer from being exposed to shock hazards.
3
KX-FT932FX-B
(Example:Digital board)
Note: The “PbF” marked may be found on different areas of the same P.C.Board,depending on manufacture date.
1.2. AC Caution
For safety, before closing the lower cabinet, please make sure of the following precautions.
1. The earth lead is fixed with the screw.
2. The AC lead is connected properly to power supply unit.
3. Wrap the earth lead around the core 5 times.
4. Wrap the AC lead around the core 5 times.
4
KX-FT932FX-B
5
KX-FT932FX-B
6
KX-FT932FX-B
2 Warning
2.1. About Lead Free Solder (PbF: Pb free)
Note:
In the information below, Pb, the symbol for lead in the periodic table of elements, will refer to standard solder or solder that con-
tains lead.
We will use PbF solder when discussing the lead free solder used in our manufacturing process which is made from Tin, (Sn),
Silver, (Ag), and Copper, (Cu).
This model, and others like it, manufactured using lead free solder will have PbF stamped on the PCB. For service and repair
work we suggest using the same type of solder although.
Caution
• PbF solder has a melting point that is 50° ~ 70° F, (30° ~ 40°C) higher than Pb solder. Please use a soldering iron with tempera-
ture control and adjust it to 700° ± 20° F, (370° ± 10°C).
• Exercise care while using higher temperature soldering irons.: Do not heat the PCB for too long time in order to prevent solder
splash or damage to the PCB.
• PbF solder will tend to splash if it is heated much higher than its melting point, approximately 1100°F, (600°C).
• When applying PbF solder to double layered boards, please check the component side for excess which may flow onto the
opposite side (See figure, below).
The lithium battery is a critical component (type No. CR2032). Please observe for the proper polarity and the exact location
when replacing it and soldering the replacement lithium battery in.
7
KX-FT932FX-B
This symbol on the products and/or accompanying documents means that used electrical and electronic products should not be
mixed with general household waste.
For proper treatment, recovery and recycling, please take these products to designated collection points, where they will be
accepted on a free of charge basis. Alternatively, in some countries you may be able to return your products to your local retailer
upon the purchase of an equivalent new product.
Disposing of this product correctly will help to save valuable resources and prevent any potential negative effects on human health
and the environment which could otherwise arise from inappropriate waste handling. Please contact your local authority for further
details of your nearest designated collection point.Penalties may be applicable for incorrect disposal of this waste, in accordance
with national legislation.
8
KX-FT932FX-B
3 Specifications
Applicable Lines: Public Switched Telephone Network
Document Size: Max. 216 mm in width
Max. 600 mm in length
Effective Scanning Width: 208 mm
Recording Paper Size: 216 × max. 30 m roll
Effective Printing Width: 208 mm
Transmission Time*1: Approx. 15 s/page (Original mode)*2
Scanning Density: Horizontal: 8 pels/mm
Vertical:
3.85 lines/mm - in standard resolution,
7.7 lines/mm - in fine/photo resolution,
15.4 lines/mm - in super fine resolution
Photo resolution: 64-level
Scanner Type: Contact Image Sensor
Printer Type: Thermal printing
Data Compression System: Modified Huffman (MH), Modified READ (MR)
Modem Speed: 9,600 / 7,200 / 4,800 / 2,400 bps; Automatic Fallback
Operating Environment: 5 - 35°C, 20 - 80% RH (Relative Humidity)
Dimensions (H×W×D): Approx. height 121 mm × width 352 mm × depth 224 mm
Mass (Weight): Approx. 2.7 kg
Power Consumption: Standby: Approx. 1.5 W
Transmission: Approx. 13 W
Reception: Approx. 30 W (When receiving a 20% black document)
Copy: Approx. 35 W (When copying a 20% black document)
Maximum: Approx. 110 W (When copying a 100% black document)
Power Supply: 220 V - 240 V AC, 50/60 Hz
Fax Memory Capacity*3: Approx. 28 pages of memory reception
(Based on the ITU-T No. 1 Test Chart in standard resolution, with original mode.)
* 1 Transmission speed depends upon the contents of the pages, resolution, telephone line conditions and capability of the other
party's machine.
* 2 Transmission speed is based upon the ITU-T No. 1 Test Chart with original mode. If the capability of the other party's machine is
inferior to your unit, the transmission time may be longer.
* 3 If an error occurs during fax reception, such as a paper jam or if the recording paper runs out, the fax and subsequent faxes will
be retained in memory.
Note:
Design and specifications are subject to change without notice.
9
KX-FT932FX-B
4 General/Introduction
4.1. Optional Accessories
*1 Use only the included or specified recording paper. Using other recording paper may affect print quality and/or
cause excessive wear to the thermal head.
10
KX-FT932FX-B
6 Technical Descriptions
6.1. Connection Diagram
11
KX-FT932FX-B
12
6.2.1.
POWER SUPPLY BOARD OPERATION PANEL
+24 Tact SW
LCD PANEL
English 2 lines MESSAGE
+6V
GATE
SENSOR x2
ARRAY (Doc sensor,
Read position sensor)
KEY MATRIX MIC
(Not Used)
FLASH FLASH
+6V DRAM
4Mbit 4Mbit
4Mbit PSHORT
PROGRAM (TAM Model) IC5
REG 3.3V
3.3V 3.3V MODEM LINERX LINE
IC4 IC2 IC6 Transformer
+5V Rx
REG BOA LINETX
Relay
+3.3
13
Tx
THERMAL RESET
24MHz ANALOG
HEAD CPC
SW
2 strobe +24V (Not Used)
IC10
OSC 32.256MHz EXT. LINE
OP-PANEL
CPU I/F
FET THON
TONE1 MONRX
PRINTER 64Kbit 256kbit TONE
BUFFER SRAM ROM
CONTROL
STB1,2 (Not Used)
THLAT,THCLK, ASIC VOL ACK_EN
+5V THDAT H/SRX
IC1
Tr LED ON +24V
H/STX_MUTE BELL
IMAGE
A/D
PROCESSING
CLK, SIG
MOTOR JAM
SERIAL
I/F
CIS I/F RTC
HOOK
3.3V chip
PAPER RLY
IC7
32.768KHz MOTOR DRIVER
To FLASH
PROGRAMMER MOTOR
SPEAKER HANDSET
KX-FT932FX-B
KX-FT932FX-B
14
KX-FT932FX-B
15
KX-FT932FX-B
16
KX-FT932FX-B
1. During a momentary power interruption, a positive reset pulse of 50~70 msec is generated and the system is reset com-
pletely.
2. The watch dog timer, built-in the ASIC (IC1), is initialized by the CPU about every 1.5 ms.
When a watch dog error occurs, pin 115 of the ASIC (IC1) becomes low level.
The terminal of the 'WDERR' signal is connected to the reset line, so the 'WDERR' signal works as the reset signal.
17
KX-FT932FX-B
18
KX-FT932FX-B
CROSS REFERENCE:
Thermal Head(P.22)
19
KX-FT932FX-B
20
KX-FT932FX-B
21
KX-FT932FX-B
2. Circuit Operation
There are 27 driver ICs aligned horizontally on the thermal head and each one of these ICs can drive 64 heat emitting regis-
ters. This means that one line is at a density of 64×27=1728 dots=(8 dots/mm).
White/Black (white=0, black=1) data in one line increments is synchronized at IC1 pin 117 (THCLK), and sent from IC1 pin 116
(THDAT) to the shift register of the ICs. The shift registers of the 27 ICs are connected in series, and upon the shift of dot
increment 1728, all the shift registers become filled with data, and a latch pulse is emitted to each IC from IC1 pin 118
(THLAT).With this latch pulse, all the contents of the shift registers are latched to the latch registers. Thereafter, through the
addition of strobes from the IC1 pins (103 - 104) only black dot locations (=1) among latched data activates the driver, and the
current passes to heat the emitting body causing heat emission.
Here, the two line strobes, STB1 and STB2, impress at intervals of 9.216 msec, as required for one-line printout.
The sequence is shown on the next page. [Moreover, for the strobe width, the thermistor value inside the thermal head is
detected according to IC1 pin 4. (See Block Diagram (P.21).) Depending on that value, the strobe width is recorded in
FLASH (IC2).
Accordingly, the strobe width is determined.
When the thermal head is not used, the IC1 (17, HEADON) becomes low, Q6 turns OFF, Q7 turns OFF, and the +24 V power
supply for the thermal head driver is not impressed to protect the IC.
22
KX-FT932FX-B
23
KX-FT932FX-B
When an original document is inserted and the start button pressed, pin 129 of IC1 goes to a high level and the transistor Q14 turns
on.This applies voltage to the light source to light it. The contact image sensor is driven by each of the FTG-F1 signals output from
IC1, and the original image illuminated by the light source undergoes photoelectric conversion to output an analogue image signal
(AIN). The analogue image signal is input to the system ASIC on AIN1 (pin 3 of IC1) and converted into 8-bit data by the A/D con-
verter inside IC1. Then this signal undergoes digital processing in order to obtain a high-quality image.
24
KX-FT932FX-B
When the motor is OFF, gate array IC1 pin 124 becomes a low level and Q2 and Q1 also turns OFF. Instead of +24V, +5V is
suplied through D501 so that the motor is held in place.
25
KX-FT932FX-B
26
KX-FT932FX-B
Digital Board
Signal (IC1-119 Pin)
Home position Low level
Other High level
Analog Board
Signal (IC1-20 Pin)
Paper Low level
No paper High level
27
KX-FT932FX-B
Digital Board
SW Signal
ON-Hook OFF High level (IC1-43 pin)
OFF-Hook ON Low level
Analog Board
Signal (IC1-21 Pin)
Paper Low level
No paper High level
28
KX-FT932FX-B
Operation Board
Signal (IC1-5 pin)
Out of the Read Position High level
At the Read Position Low level
Operation Board
Signal (IC1-6 pin)
No document High level
Set document Low level
29
KX-FT932FX-B
30
KX-FT932FX-B
31
KX-FT932FX-B
Explanation of Signals
Control signals are comprised mainly of 8-bit identification signals and the data signals added to them. Data signals are added
to DIS and DCS signals.
Signal.....DIS (Digital Identification Signal)
Identification Signal Format.....00000001
Function:
Notifies the capacity of the receiving unit. The added data signals are as follows.
32
KX-FT932FX-B
33
KX-FT932FX-B
Note 1 - Standard facsimile units conforming to T.2 must have the following capability: Index of cooperation (IOC)=264.
Note 2 - Standard facsimile units conforming to T.3 must have the following capability: Index of cooperation (IOC)=264.
Note 3 - Standard facsimile units conforming to T.4 must have the following capability: Paper length=297 mm.
34
KX-FT932FX-B
35
KX-FT932FX-B
2. Facsimile Reception
The analog image data which is received from the telephone line passes through the NCU section and enters pin 47 of the
modem (IC5). The signals that enter pin 47 of the modem (IC5) are demodulated in the board to digital image signals, then
placed on the data bus.
In this case, the image signals from the telephone line are transmitted serially. Hence, they are placed on the bus in 8 bit
units. Here, the internal equalizer circuit reduces the image signals to a long-distance receiving level.
This is designed to correct the characteristics of the frequency band centered about 3 kHz and maintain a constant receiving
sensitivity. It can be set in the service mode.
6. Caller ID Detection
The caller ID signal which is received from the telephone line/passes through IC1 pin (2-1). And it enters pin 50 of the modem
(IC5).
36
KX-FT932FX-B
37
KX-FT932FX-B
38
KX-FT932FX-B
39
KX-FT932FX-B
2. Circuit Operation:
The Caller ID signal from TEL LINE is processed with MODEM (IC5).
Refer to Sgnal Route (P.108) for the route of Caller ID (DTMF) signal.
40
KX-FT932FX-B
41
6.9.2.
KX-FT932FX-B
R10
C8
+2.0V +24VA
IC2
R2 8 R13 C17 T1 R41 L31
C4 2 ZNR1
1 ( )
3
Circuit Diagram
R5 C7 4 CN3
R18 C21 C29 L19
Ref SA1 1a
D1 R54 4 POS1 2 b
R11 ( ) L32
3
5
C14 RLY1 SA2
R14 R15
R22 R23
R26 R27
C28
+5VD
R35 R38
42
BELL C38 L25
PC1 4 1 CN4
L26
1 EXT
3 2 R45 2 TEL
+24V
Analog Board
RLY1
2
D8
1
Digital Board
RLY
Q7
13 13 C216 R221 R220 C217
To IC5
L1 CN1 CN2
R219 D506
KX-FT932FX-B
LCD
CN2
ASIC
CN206 CN1
XLED8, 9
XLED13 LED
43
KX-FT932FX-B
44
KX-FT932FX-B
Block Diagram
AC
Input A G
Input Rectifier + 24V 24V
Circuit Circuit C106 - Output
Kick-on
B Voltage Surge Circuit
Circuit absorber
D110 Converter circuit
Circuit
A-B Voltage Wave Form
R102 C GND
Q101 Surge 9~6V
absorber 6V
D circuit Output
0 Circuit
C-D Voltage Wave Form Control
Circuit
E
0 IC101 H
O.C.L
Over voltage
E-F
G-H Voltage Wave Form
F
0 Error Detecting
Circuit
[Input Circuit]
The input current goes into the input rectifier circuit through the filter circuit. The filter circuit decreases the noise voltage and the
noise electric field strength.
[Rectifier Circuit]
The input current is rectified by D101,D102,D103 and D104 and charges C106 to make DC voltage. Then it supplies power to the
converter circuit.
45
KX-FT932FX-B
When Q1 is ON, the energy is charged in the transfer primary coil according to E1. When Q1 is OFF, the energy is output from the
secondary transfer as follows.
L → D1 → Load → L
Then the power is supplied to the Load. When Q1 is ON, power is not output from the secondary side. The output voltage is fed
back in the control IC according to the error amp rectifier. Then depending on how TON is controlled, stabilization occurs. Also,
when the current load becomes too large, in order to decrease the voltage output, the increase in is controlled and the output
voltage is stabilized.
Therefore, basically the timing: Ton/Toff of Q1 controls the output voltage.
46
KX-FT932FX-B
Dummy load method (to quickly check the power supply output)
47
KX-FT932FX-B
48
KX-FT932FX-B
Buttons
49
KX-FT932FX-B
Note:
• Avoid excessive heat or humidity.
• Use the unit within the following ranges of temperature and
humidity.
• Ambient temperature: 5°C to 35°C
• Relative humidity: 20% to 80% (without condensation)
• Power cord length should be less than 5 meters. Using a
longer cord may reduce the voltage or cause malfunctions.
• Avoid direct sunlight.
• Do not install near devices which contain magnets or gener-
ate magnetic fields.
• Do not subject the unit to strong physical shock or vibration.
• Keep the unit clean. Dust accumulation can prevent the unit
from functioning properly.
• To protect the unit from damage, hold both sides when you
move it.
Caution:
• When you operate this product, the power outlet should
be near the product and easily accessible.
• Be sure to use the telephone line cord included in this
unit.
• Do not extend the telephone line cord.
• Keep the unit away from walls as far as possible to pre-
vent a recording paper jam.
Note:
Before you can make calls, the dialling mode setting may
need to be changed.
50
KX-FT932FX-B
8.3. Installing the Recording Paper 5. Close the top cover securely by pushing down on both
sides.
1. Open the top cover by pressing the top cover release but-
ton ( ).
2. Install the recording paper. 6. Press [FAX/START], then tear off the excess paper by
pulling it towards you.
Note:
3. Insert the leading edge of the paper into the opening • If the paper is secured with glue or tape, cut approxi-
mately 15 cm from the beginning of the roll before install-
above the thermal head ( ).
ing it.
• When the power cord is connected, a message is printed
each time the top cover is opened then closed. If the
recording paper is installed upside down, the message
will not be printed. Install the paper correctly.
• For accessory information, see Optional Accessories
(P.10).
51
KX-FT932FX-B
9 Operation Instructions
9.1. Setting Your Logo
Your logo will be printed on the top of each page sent from your
unit. The logo can be your name or the name of your company.
1. Press [MENU].
3. Press [SET].
• The cursor ( ) will appear on the display.
Document weight
• Single sheet: 45 g/m2 to 90 g/m2
4. Enter your logo, up to 30 characters. See the following
• Multiple sheest: 60 g/m2 to 80 g/m2
character table below for details.
Note:
• Remove clips, staples or other fasteners.
• Do not send or copy documents that are on the following 5. Press [SET].
types of paper: (Make a copy of the document using another • The next feature will be displayed.
copier and send the copy.)
— Chemically treated paper such as carbon or carbonless 6. Press [MENU].
duplicating paper
— Electrostatically charged paper
— Badly curled, creased or torn paper
— Paper with a coated surface
— Paper with a faint image
— Paper with printing on the opposite side that can be seen
through the other side, such as newsprint.
• Check that ink, paste or correction fluid has dried com-
pletely.
• To send a document with a width of less than 210 mm, we
recommend using a copy machine to copy the original docu-
ment onto A4 or letter-sized paper, then sending the copied
document.
52
KX-FT932FX-B
3. Press [ ].
To correct a mistake
1. Press [ ] or [ ] to move the cursor to the incorrect
character.
2. Press [STOP].
• To erase all characters, press and hold [STOP].
3. Enter the correct character.
53
KX-FT932FX-B
10 Test Mode
The codes listed below can be used to perform simple checks for some of the unit's functions. When complaints are received
from customers, they provide an effective tool for identifying the locations and causes of malfunctions. To do this, you set the
Service mode (Refer to Operation Flow (P.56).) first, then operate the below test items.
LCD CHECK Service Mode “5” “5” “8” Checks the LCD indication.
SET Illuminates all the dots to check if they are normal.
Refer to Operation Panel Section (P.113).
KEY CHECK Service Mode “5” “6” “1” Checks the button operation.
START (any key) Indicates the button code on the LCD while the button is pressed. Refer to But-
ton Code Table (P.55).
Refer to Operation Panel Section (P.113).
MEMORY CLEAR Service Mode “7” “1” “0” Refer to Memory Clear Specification (P.59).
(except History data) SET
SENSOR CHECK Service Mode “8” “1” “5” If you enter this mode and operate sensor levers with your hands, the LCD dis-
play of the related sensor (or switch) turns ON / OFF. Also, when copying a doc-
ument, the related sensor will turn ON / OFF.
For each sensor's operation, refer to Sensors and Switches (P.26).
Do Sn Co Jm Ct : LCD DISPLAY
Do: Document set sensor
:Paper inserted. Turns on when a document is inserted.
Sn: Read position sensor.
:At the read position, turns on when the front cover is opened and the sensor
lever is pressed directory.
Co: Cover open sensor
:Turns on and off when the front cover is opened and closed.
Jm: JAM sensor
:When JAM sensor is on “Jm” functions.
PRINT TEST PAT- Service Mode “8” “5” “2” Prints out the test pattern.
TERN SET Used mainly at the factory to test the print quality.
You can select 1~9. (See Print Test Pattern (P.55))
Note:
The numbers in the boxes (XXX) indicate the keys to be
input for the various test modes.
54
KX-FT932FX-B
key High Frequency (Hz) key Low Frequency (Hz) High (Hz) 1209 1336 1477
“1” 697 “5” 1209 Low (Hz)
“2” 770 “6” 1336 697 “1” “2” “3”
“3” 852 “7” 1477 770 “4” “5” “6”
“4” 941 “8” 1633 852 “7” “8” “9”
941 “ ” “0” “#”
When set to OFF (=2), the 12 keys and transmission fre-
quencies are as shown.
Note:
After performing this check, do not forget to turn the setting off.
Otherwise, dialing in DTMF signal will not work.
55
KX-FT932FX-B
11 Service Mode
The programming functions are used to program the various features and functions of the machine, and to test the machine.
This facilitates communication between the user and the service man while programming the unit.
56
KX-FT932FX-B
57
KX-FT932FX-B
58
KX-FT932FX-B
*1 Execute Service Mode #550 when you want to reset the all setting data keeping the user information.
*2 Execute Service Mode #710 to clear the user information in case that Main Unit is recycled.
Note:
Please restart a power supply after clearing a memory.
59
KX-FT932FX-B
Note:
The above values are the default values.
60
KX-FT932FX-B
Note:
The above values are the default values.
61
KX-FT932FX-B
Note:
See the following descriptions of this report. Item No. (1) ~ (44) are corresponding to the listed items in Descriptions of the
History Report (P.63).
62
KX-FT932FX-B
12 Troubleshooting Guide
12.1. Troubleshooting summary
12.1.1. Troubleshooting
After confirming the problem by asking the user, troubleshoot according to the instructions and observe the following
precautions.
12.1.2. Precautions
1. If there is a problem with the print quality or the paper feed, first check if the installation space and the print paper meets the
specifications, the paper selection lever/paper thickness lever is set correctly, and the paper is set correctly without any slack.
2. Before troubleshooting, first check that the connectors and cables are connected correctly (not loose).
If the problem occurs randomly, check it very carefully.
3. When connecting the AC power cord with the unit and checking the operation, exercise utmost care when handling electric
parts in order to avoid electric shocks and short-circuits.
4. After troubleshooting, double check that you have not forgotten any connectors, left any loose screws, etc.
5. Always test to verify that the unit is working normally.
64
KX-FT932FX-B
• The cover is open. Close it and press [FAX/START] to clear • The document is jammed. Remove the jammed document.
the message. (Refer to Document Jams - Sending (P.137).)
• The unit has run out of recording paper. Install recording • Press [STOP] to eject the jammed document.
paper and press [FAX/START] to clear the message.
65
KX-FT932FX-B
FF COMMUNICATION ERROR SND & RCV Modem error. For the DCN, DCN, etc. abbreviations, refer to Modem 12
Section (P.30).
SND=TRANSMISSION RCV=RECEPTION
66
KX-FT932FX-B
67
KX-FT932FX-B
CROSS REFERENCE:
Test Mode(P.54)
68
KX-FT932FX-B
CROSS REFERENCE:
Test Mode(P.54)
69
KX-FT932FX-B
CROSS REFERENCE:
Test Mode(P.54)
70
KX-FT932FX-B
71
KX-FT932FX-B
CROSS REFERENCE:
Maintenace(P.129)
ADF (Auto Document Feed) Section(P.93)
Operation Panel Section(P.167)
CROSS REFERENCE:
Test Mode(P.54)
72
KX-FT932FX-B
73
KX-FT932FX-B
74
KX-FT932FX-B
CROSS REFERENCE:
Test Mode(P.54)
75
KX-FT932FX-B
76
KX-FT932FX-B
12.3.2.1. Journal 2
Refer to JOURNAL 2 in Printout Example(P.78).
Journal 2 displays the additional detailed information about the last 30 communications.
Descriptions:
(1) RCV. MODE
Indicates which receive mode the unit was in when the unit received a fax message.
This information is also displayed when the unit transmitted a fax message.
(2) SPEED
Indicates the speed of the communication. If multiple pages are transmitted or received, it indicates the last page's communication
speed. If there is a communication error, "?" is displayed.
(3) RESOLUTION
Indicates the resolution of the communication. If multiple pages are transmitted or received, it indicates the last page's resolution. If
there is a communication error, "?" is displayed.
(5) ERROR→MEMORY
Indicates the reason why the unit received a fax message in memory.
If you look at No.11 in the JOURNAL 2 in Printout Example(P.78), it shows the fax message was received in memory due to
"PAPER OUT" error.
77
KX-FT932FX-B
12.3.2.2. Journal 3
Refer to JOURNAL 3 in Printout Example (P.78). (9) ERROR LINE(RX)
Descriptions: When an error occurs while receiving a fax, this shows the
(6) ENCODE number of error lines.
Compression Code: MH/MR
(10) MAKER CODE
(7) MSLT This shows a 2 digit code of the other party's fax machine
MSLT means Minimum Scan Line Time. Used only at the brand.
factory.
0E: "KX" model
(8) EQM 00: Unknown
EQM means Eye Quality Monitor. Used only at the factory. 79: "UF" model
19: "Xerox" model
78
KX-FT932FX-B
79
KX-FT932FX-B
CROSS REFERENCE:
Operation Panel Section(P.113)
ADF (Auto Document Feed) Section(P.93)
Maintenace(P.129)
80
KX-FT932FX-B
Note:
• "596: Transmit level set" represents a service code. (Refer to Service Function Table(P.57).)
81
KX-FT932FX-B
Note:
"596: Transmit level set" represents a service code. (Refer to Service Function Table(P.57).)
Remarks:
Regarding the reception problem, we have investigated the conceivable causes in the flow chart except for the software-related
errors. However, some troubles may occur due to the software-related problems such as "OUT OF PAPER" when the fax
switches to the memory receiving mode and the memory capacity becomes full of the unprintable data. In this case, error mes-
sages [MEMORY FULL] and its main cause, for example "CHECK PAPER" are displayed on the LCD. Once you solve the main
problem, [MEMORY FULL] will be cancelled and the reception problem will be resolved.
LCD display messages indicating the error causes are shown below.
COVER OPEN
UNIT OVERHEATED (COVER OPEN, etc.)...Reset the unit.
PAPER JAMMED
Please refer to Error Messages-Display (P.65) for the above items. If it turns out to be a hardware deformity, please check
each sensor. (Refer to Test Mode (P.54).)
82
KX-FT932FX-B
CROSS REFERENCE:
Analog Board Section(P.108)
Test Mode(P.54)
83
KX-FT932FX-B
12.3.3.1.5. The unit can copy, but cannot either transmit/receive long distance or interna-
tional communications
The following two causes can be considered for this symptom.
Cause 1:
The other party is executing automatic dialing, the call has been received by this unit, and the CED or DIS signal response time
is too long. (In most cases, this unit detects the CNG signal and can respond to CED or DIS.) (According to the ITU-T standard,
the communication procedure is cancelled when there is no response from the other party within 35 sec, so that the other party
releases the line.)
(Echo/Echo Canceler)
The signal from FAX1 reaches FAX2 via stations 1 and 2, but the reflection signal at station 2 also returns via station 1 (echo).
As the distance between station 1 and station 2 is far, the echo returns to FAX 1 at a max of 600 msec after transmission. There
is a possibility that this signal is detected erroneously as the signal from FAX2. For a normal call, there is also a possibility that
the echo of their own voice will make the call difficult to understand. For this reason, each station (station 1 and station 2)
attaches echo cancelers (S1 and S2) for international lines or long distance lines. For the echo canceler, the level of the trans-
mission signal from FAX 1 is compared with the level of the reception signal from FAX2. When the transmission signal is larger,
S1 is closed while S2 is opened when it is smaller. In other words, for transmission from FAX1, S1 is closed and S2 is open, so
that the echo does not return to FAX1.
84
KX-FT932FX-B
No. Countermeasure Side Echo Communication Problem Example Countermeasure Service Code
1 Sending side Some time is needed to compare the level Add a dummy signal to the beginning of Service code (521)
of the receiving and sending signals for the the training signal. (International mode select)
echo canceler. The header of the training This countermeasure becomes
signal lacks due to a switching delay to the default value.
close S1.
2 Receiving side The echo canceler function stops accord- Change to a 1100Hz CED signal fre- Service code (520)
ing to a CED signal frequency of 2100Hz quency. (Refer to Fig. b) (CED frequency select)
Receiving side (S1 and S2 are both ON), a DIS signal is Change the regular rime of 75 msec Service code (593)
returned as an echo, and a DCS signal between the CED signal and DIS signal (Time between CED and 300
from the sending side overlaps the DIS to 500 msec. This will give at least 250 bps)
echo. Then the receiving side FAX cannot msec to recover the echo canceler
retrieve the DCS signal. operation. (Refer to Fig. c)
Sending side (Refer to Fig. a) The sending side FAX sends a DCS Service code (594)
signal not after receiving the 1st DIS (Overseas DIS detection
signal but after receiving the 2nd DIS select)
signal. (Refer to Fig. d)
3 Sending side Communication failure occurs in a long dis- Decrease the transmission level from - Service code (596)
tance communication on the telephone line 9 dBm to -15 dBm and the echo level (Transmit level set)
without an echo canceler. will decrease.
4 Sending side Decrease the receiving sensitivity from Service code (598)
Receiving side or -13 dBm to about -32 dBm so an echo (Receiving sensitivity)
signal will not received.
5 Sending side There are some cases (e.g. Mobil comms.) Set additional Pause time (Service Service code (774)
Receiving side which cause the collision of TX / RX signals mode: code No. 774) in between the (T4 timer)
due to the delay / echo and noise of the original and its repeated signals, to pre-
network / terminal. (Refer to Fig. e) vent the collision of the signals at both
end.
85
KX-FT932FX-B
(Fig. e)
12.3.3.1.6. The unit can copy, but the transmission and reception image are incorrect
(Long distance or international communication operation)
This symptom highly depends on the transmission and reception capability of the other FAX unit and the line conditions.
The countermeasures for this unit are shown below.
Transmission Operation:
Set the transmitting speed to 4800BPS (service mode: code No. 717) or select the overseas mode.
Reception Operation:
If 80% or more of the reception is incorrect, set the receiving speed to 4800BPS. (Service mode: code No. 718)
• Refer to Service Function Table(P.57).
86
KX-FT932FX-B
2. Setting up
87
KX-FT932FX-B
First, in order to check the current status of the service code parameter, print out the setup list (code: 991) and the service list
(code: 999) from the customer's fax machine.
Based on this, the parameters for the desired codes can be changed.
The procedure for changing and listing parameters is described on Entering the Remote Programming Mode and Changing
Service Codes (P.88). Also, before exiting the remote programming mode, it is advisable to obtain a new list to confirm that the
changes were made correctly.
Hint:
Since the connected telephone is in use during the remote programming mode, it may be helpful to ask the customer to switch
to the speakerphone. This frees the customer from the need to remain right next to the fax while you are making parameter set-
tings. When finished, inform the customer. Also note that in very noisy locations where the DTMF tones are not audible, the
remote programming function will not work.
12.4.1. Entering the Remote Programming Mode and Changing Service Codes
CROSS REFERENCE:
Program Mode Table (P.89)
88
KX-FT932FX-B
89
KX-FT932FX-B
Note:
Refer to Service Function Table (P.57) for descriptions of the individual codes.
Example:
If you want to set value in the "004 Transmission report mode", press the dial key number 1, 2 or 3 corresponding to the Set
Value you want to select. (1:ON/2:OFF/3:ERROR)
90
KX-FT932FX-B
CROSS REFERENCE:
Error Messages-Display(P.65)
Simple Check List(P.92)
Digital Board Section(P.100)
Power Supply Board Section(P.110)
91
KX-FT932FX-B
Receiving OK / NG
PHOTO mode OK / NG
Monitor sound OK / NG
Ringer sound OK / NG
Dial operation OK / NG
Volume operation OK / NG
Note:
• Check according to the sevvice code referring to the Test Mode (P.54).
92
KX-FT932FX-B
Note:
(*1) : Refer to Multiple Feed (P.95)
(*2) : Refer to How to Remove the Operation Board, LCD and Platen Roller (P.121)
(*3) : Refer to Test Mode (P.54)
(*4) : Refer to Digital Board Section (P.100)
(*5) : Refer to Sensor Section (P.114)
(*6) : Refer to How to Remove the Gear Block and Separation Roller (P.127)
(*7) : Refer to How to Remove the Separation Holder and Document Feed Support (P.122)
(*8) : Refer to Power Supply Board Section (P.110)
93
KX-FT932FX-B
CROSS REFERENCE:
Test Mode (P.54)
Sensor Section (P.114)
Note:
(*1) : Refer to How to Remove the Operation Board, LCD and Platen Roller (P.121)
(*2) : Refer to Disassembly and Assembly Instructions (P.118)
94
KX-FT932FX-B
Note:
(*1) : Refer to How to Remove the Separation Holder and Document Feed Support (P.122)
(*2) : Refer to Disassembly and Assembly Instructions (P.118)
(*3) : Refer to Maintenace (P.129)
95
KX-FT932FX-B
12.5.4.4. Skew
Note:
(*1) : Refer to Maintenance Items and Componet Locations (P.129)
(*2) : Refer to Disassembly and Assembly Instructions (P.118)
(*3) : Refer to How to Remove the Separation Holder and Document Feed Support (P.122)
(*4) : Refer to How to Remove the Operation Board, LCD and Platen Roller (P.121)
(*5) : Refer to How to Remove the Image Sensor (CIS) and Feed Roller (P.123)
96
KX-FT932FX-B
CROSS REFERENCE:
Thermal Head Section (P.116).
Test Mode(P.54)
CIS (Contact Image Sensor) Section (P.115).
Note:
(*1) : Refer to Maintenance Items and Componet Locations (P.129)
(*2) : Refer to Disassembly and Assembly Instructions (P.118)
(*3) : Refer to How to Remove the Operation Board, LCD and Platen Roller (P.121)
97
KX-FT932FX-B
CROSS REFERENCE:
Test Mode(P.54)
Digital Board Section (P.100)
Note:
(*1) : Refer to How to Remove the Lock Lever and Thermal Head (P.124)
(*2) : Refer to Maintenance Items and Componet Locations (P.129)
(*3) : Refer to How to Remove the Operation Board, LCD and Platen Roller (P.121)
(*4) : Refer to How to Remove the Image Sensor (CIS) and Feed Roller (P.123)
Note:
(*1) : Refer to Installing the Recording Paper (P.51)
98
KX-FT932FX-B
12.5.4.8. When Coping or Printing, an Abnormal Sound is Heard from the Unit
Note:
(*1) : Refer to Document Feeder Cleaning (P.138)
(*2) : Refer to Thermal Head Cleaning (P.138)
(*3) : Refer to Disassembly and Assembly Instructions (P.118)
(*4) : Refer to How to Remove the Motor of Gear Block (P.127)
(*5) : Refer to How to Remove the Gear Block and Separation Roller (P.127)
99
KX-FT932FX-B
Note:
1. Electrical continuity may have existed at the factory check, but a faulty contact occurred as a result of vibration, etc., during
transport.
2. Solder waste remaining on the board may get caught under the IC during transport, causing a short circuit.
Before we begin mass production, several hundred trial units are produced at the plant, various tests are applied and any mal-
functions are analyzed. (In past experiences, digital IC (especially DRAM and FLASH ROM) malfunctions are extremely rare
after installation in the product.)
This may be repaired by replacing the IC, (DRAM etc.). However, the real cause may not have been an IC malfunction but a sol-
dering fault instead.
Soldering faults difficult to detect with the naked eye are common, particularly for ASIC and RA (Resistor Array). But if you have
an oscilloscope, you can easily determine the problem site or IC malfunction by checking the main signal lines.
Even if you don't have such a measuring instrument, by checking each main signal line and resoldering it, in many cases the
problem will be resolved.
An explanation of the main signals (for booting up the unit) is presented below.
Don't replace ICs or stop repairing until checking the signal lines.
An IC malfunction rarely occurs. (By understanding the necessary signals for booting up the unit, the “Not Boot up”
display is not a serious problem.)
100
KX-FT932FX-B
Flash memory IC2 in the ASIC system is for software and also for user memory (settings, Phone book, CID memory) DRAM IC4
in the ASIC system is for work memory and also for fax memory.
The signal lines that must be normal for the system to boot up are listed here [List 1].
For signal lines other than these, even if they malfunction they do not directly affect booting up the system.
101
KX-FT932FX-B
NG Wave pattern
Note:
Refer to NG Example (P.107).
102
KX-FT932FX-B
Remarks:
When you use an oscilloscope to judge whether a signal to be tested is normal or NG, perform the signal check in exactly the
same order as in [List 1]. (If the ASIC fails to access the ROM, the ASIC cannot access DRAM normally.)
The digital circuit actually operates according to the timing combinations of these signals. If the timing of these signals is even
slightly delayed, the circuit will not work. Nor will it if the IC is defective and the output voltage level is not normal although the
timing of these signals is accurate enough to meet the specifications. (Make sure that your oscilloscope is calibrated before
starting a test.)
Therefore, it is imperative to confirm whether each IC outputs the signal at the correct level. (See the I/O Pin No. Diagram.) The
signal level should be constantly output at between 3.3V (H) and 0V (L) as described earlier.
103
KX-FT932FX-B
104
KX-FT932FX-B
105
KX-FT932FX-B
106
KX-FT932FX-B
12.5.5.3. NG Example
107
KX-FT932FX-B
108
KX-FT932FX-B
2. No pulse dialing
4. No tone dialing
109
KX-FT932FX-B
In most cases, the symptom is that nothing is output. It is more likely that the fault is in the primary side rather than the secondary
side. Check the primary side first.
110
KX-FT932FX-B
111
KX-FT932FX-B
(Q101)
The worst case of Q101 is a short-circuit between the Drain and Gate because damage expands to the peripheral circuit of Q101.
This is due to a very high voltage through the Gate circuit which is composed of R128, R109, D109 and IC101.
You should change all of the parts listed as follows.
F101, Q101, R128, R109, D109, IC101
(D201)
If D201 is broken, the oscillation circuit in the power supply cannot operate. Check it with an electric tester.
112
KX-FT932FX-B
CROSS REFERENCE:
Test Mode(P.54)
CROSS REFERENCE:
Test Mode(P.54)
113
KX-FT932FX-B
114
KX-FT932FX-B
CROSS REFERENCE:
Test Mode(P.54)
115
KX-FT932FX-B
116
KX-FT932FX-B
117
KX-FT932FX-B
CROSS REFERENCE:
A-2 : How to Remove the Operation Panel Block (P.120)
A-3 : How to Remove the Operation Board, LCD and Platen Roller (P.121)
A-4 : How to Remove the Separation Holder and Document Feed Support (P.122)
A-5 : How to Remove the Image Sensor (CIS) and Feed Roller (P.123)
A-7 : How to Remove the Lock Lever and Thermal Head (P.124)
B-1 : How to Remove the Bottom Frame (P.125)
B-3 : How to Remove the Gear Block and Separation Roller (P.127)
118
KX-FT932FX-B
CROSS REFERENCE:
B-1 : How to Remove the Bottom Frame (P.125)
B-2 : How to Remove the Analog Board, Digital Board, Power Supply Board and Power Cord (P.126)
B-3 : How to Remove the Gear Block and Separation Roller (P.127)
B-4 : How to Remove the Motor of Gear Block (P.127)
119
KX-FT932FX-B
120
KX-FT932FX-B
14.2.2. How to Remove the Operation Board, LCD and Platen Roller
121
KX-FT932FX-B
14.2.3. How to Remove the Separation Holder and Document Feed Support
122
KX-FT932FX-B
14.2.4. How to Remove the Image Sensor (CIS) and Feed Roller
123
KX-FT932FX-B
124
KX-FT932FX-B
125
KX-FT932FX-B
14.2.7. How to Remove the Analog Board, Digital Board, Power Supply Board and Power
Cord
126
KX-FT932FX-B
127
KX-FT932FX-B
128
KX-FT932FX-B
15 Maintenace
15.1. Maintenance Items and Componet Locations
15.1.1. Outline
MAINTENANCE AND REPAIRS ARE PERFORMED USING THE FOLLOWING STEPS.
1. Periodic maintenance
Inspect the equipment periodically and if necessary, clean any contaminated parts.
2. Check for breakdowns
Look for problems and consider how they arose.
If the equipment can be still used, perform copying, self testing or communication testing.
3. Check equipment
Perform copying, self testing and communication testing to determine if the problem originates from the transmitter, receiver
or the telephone line.
4. Determine causes
Determine the causes of the equipment problem by troubleshooting.
5. Equipment repairs
Repair or replace the defective parts and take appropriate measures at this stage to ensure that the problem will not recur.
6. Confirm normal operation of the equipment
After completing the repairs, conduct copying, self testing and communication testing to confirm that the equipment operates
normally.
7. Record keeping
Make a record of the measures taken to rectify the problem for future reference.
129
KX-FT932FX-B
* These values are standard and may vary depending on usage conditions.
130
KX-FT932FX-B
<Fig. A>
131
KX-FT932FX-B
15.2.2.1. TX Mode
Swing Gear A engages Gear TX and conveys its drive power to the Separation Roller Gear for pre-feeding documents.
Fig. B: TX mode
15.2.2.2. RX Mode
Swing Gear B engages Gear RX and conveys its drive power to the Platen Roller Gear for printing the received data.
Fig. C: RX mode
132
KX-FT932FX-B
133
KX-FT932FX-B
134
KX-FT932FX-B
CROSS REFERENCE:
Sensor Section (P.114)
Error Messages-Display (P.65)
Note:
See Sensors and Switches (P.26)
135
KX-FT932FX-B
15.2.3.4. Copying
CROSS REFERENCE:
Sensor Section (P.114)
136
KX-FT932FX-B
15.3. Jams
15.3.1. Recording Paper Jams ( ).
1. Open the top cover by pressing the top cover release but-
ton ( ).
Note:
• Do not pull out the jammed paper forcibly before opening
top cover.
137
KX-FT932FX-B
4. Connect the power cord and the telephone line cord. 5. Install the recording paper and close the top cover
securely by pushing down on both sides.
5. Close the top cover securely by pushing down on both
sides.
138
KX-FT932FX-B
16 Miscellaneous
16.1. Terninal Guide of the ICs, Transistors and Diodes
16.1.1. Digital Board
139
KX-FT932FX-B
140
KX-FT932FX-B
16.2.1. Preparation
• PbF (: Pb free) Solder
• Soldering Iron
Tip Temperature of 700°F ± 20°F (370°C ± 10°C)
Note: We recommend a 30 to 40 Watt soldering iron. An expert may be able to use a 60 to 80 Watt iron where someone with
less experience could overheat and damage the PCB foil.
• Flux
Recommended Flux: Specific Gravity → 0.82.
Type → RMA (lower residue, non-cleaning type)
Note: See About Lead Free Solder (PbF: Pb free) (P.7).
2. Make a few cuts into the joint (between the IC and its pins) first and then cut off the pins thoroughly.
When you attach a new IC to the board, remove all solder left on the land with some tools like a soldering wire. If some solder is left
at the joint on the board, the new IC will not be attached properly.
*Check the accuracy of the IC setting with the corresponding soldering foil.
141
KX-FT932FX-B
3. Solder the pins, sliding the soldering iron in the direction of the arrow.
142
KX-FT932FX-B
143
KX-FT932FX-B
144
KX-FT932FX-B
MEMO:
145
KX-FT932FX-B
17 Schematic Diagram
17.1. Digital Board
4M DRAM 4M FLASH
FOR PROGRAM
IC4
A[4] 10 2 D[0]
MOTOR BLOCK A[5] 11
A0
A1
DQ1
DQ2
3 D[1] IC2
A[6] 12 4 D[2]
A[7] 13
A2 DQ3
5 D[3] A0 A[0] A[0] 20 A0 D0 21 D[0]
RBA[0] 16
A3 DQ4
24 D[4] A1 A[1] A[1] 19 A1 D1 22 D[1]
A4 DQ5 A2 A[2] A[2] 18 23 D[2] D[0] D0
RBA[1] 17 25 D[5] A[3] A[3]
A2 D2
D[3] D[1]
+24V RBA[2] 18
A5 DQ6
26 D[6] A3 17 A3 D3 25 D1
M RBA[3] 19
A6 DQ7
27 D[7] A4 A[4] A[4] 16 A4 D4 26 D[4] D[2] D2
F1 1.25A R1 820 R2 A7 DQ8 A5 A[5] A[5] 15 27 D[5] D[3] D3
RBA[4] 20
A8 A[6] A[6]
A5 D5
D[6] D[4]
RBA[5] 9
A6 14 A6 D6 28 D4
1.5K 1/2W A9R A7 A[7] A[7] 13 A7 D7 29 D[7] D[5] D5
Q1 BR4
+3.3VD A8 A[8] A[8] 3 D[6] D6
+5V RXE 6
NC6 A[9] A[9]
A8
D[7]
+3.3VD A9 2 A9 D7
Q2 21
NC21 VCC-14
14
A[10] A[10]
1
A10 31 A10 +3.3VD
Z0.1u
Z0.1u
220
C102
C103
WE A12 A[12] A[12] 12
WE 7
10K
10K
22 A12
RBA[0] RBA[0]
IC7 8
OE
15
A13 4 A13 VDD 8
R3
DG
D501
23
RAS VSS-15
28
A14 RBA[1] RBA[1] 5 A14 VSS 24
D502 BR1 20V CAS VSS-28 A15 RBA[2] RBA[2] 11 A15
NC R100
NC R101
Z0.1u
CN3 9
GND
8 A16 RBA[3] RBA[3] 10 A16
C104
DG A17 RBA[4] RBA[4] 6 A17
COM 1
10 7 A18 RBA[5] 30 CE
32 OE A18 9
RM3
)
RM3 2
11 6
(
C100
C101
RM2 3
RM2 RBA[5]
12 5
RM1 4
RM1 RD WR DG
13 4
DG
RM0
RM0 5
14 3 (1)
+24LV BLEEDER_ON
BR5
15 2 PG
680 2W
16 1
R172
(2)
PG
(3)
(4)
(5)
(6)
CE1 +3.3VD CE2
THERMAL HEAD +24V R102 10K
Q7
BLOCK ROMCSMFCS
J2
+3.3VD
8 1 IC11
K0.1u
5.6K
7 2
1 INB 5
C10
R10
6 3 VCC
5 4
+24VF +24VF 2
INA
3 4
4.7K
GND
R12
OUT
2.2K
R11
C105 Z0.1u
DG
DG
(7)
NC
( )
C11
PG Q6
Q4 Q5
HEADON (8)
RBA[5]
RBA[4]
RBA[3]
RBA[2]
RBA[1]
RBA[0]
A[12]
A[11]
A[10]
A[9]
A[8]
A[7]
A[6]
A[5]
A[4]
A[3]
A[2]
A[1]
A[0]
+2.5VD
RXE
CN4 PG
COM 1
TH-TMP
R13 100
LATCH 2
R14 100
STB1 3
C12 +3.3VD
GND 4
Z0.1u THLAT
+3.3V 5
STB1 XRESET
TM 6
L21 +3.3VD +2.5VD
R15 100 THCLK RBA6
CLOCK 7 (9)
GND 8
R16 100 STB2
C179
Z0.1u
(10)
STB2 9
STB1
R17 100 THDAT STB2
Z0.1u
Z0.1u
DATA 10
C178
C177
COM 11
(11)
NC
NC
NC
J100p
J100p
2.2K
VSS 108
VDD3.3V 107
XRESET106
STB3 105
STB2 104
STB1 103
RBA6/IOP96102
RBA5/OP101
RBA4 100
RBA3 99
RBA2 98
RBA1 97
RBA0 96
ADR12 95
ADR11 94
ADR10 93
ADR9 92
ADR8 91
ADR7 90
ADR6 89
VDD2.5V 88
VSS 87
ADR5 86
ADR4 85
ADR3 84
ADR2 83
ADR1 82
ADR0 81
XWR 80
XRD 79
XR0MCS 78
DB7 77
DB6 76
DB0 75
VDD3.3V 74
VSS 73
J100p
)
R150
C150
C13
C14
(
+5V
R18
R19
R20
C154
126 VDD2.5V XTEST 55 (13)
CUTTER POSITION ACK_EN Z0.1u
127 VSS VDD3.3V 54
C175
SENSOR 128 TM1/IOP11 VSS 53
4.7K
R33
+24V
100 21 IRDATXD/IOP81
14 2.5V/BATTIN
FMEND0/IOP26
24 RXD/IOP31
23 TXD/IOP30
+3.3VD
11 XBACKEN
31 VOL2OUT
DG
2 VDDA3.3
27 VDD2.5V
35 VDD3.3V
C171
8 X32OUT
32 VOL3IN
19 CPC/IP
20 RVN/IP
28 TONE1
29 TONE2
18 FA/OP
17 F2/OP
Z0.1u
9 X32IN
1 VSSA
7 VSSA
33 XNMI
4.7K
+3.3VA
3 AIN1
4 AIN2
5 AIN3
MIC 1
15 FTG
36 VSS
+5V
16 F1
10
R153
C168
Z0.1u
34
+5V 2
C50
R59
K1000p
3
(16)
10V Z4.7u
DG R51 270
470
KSTART
C158
47K
KSTART 4
NC
C166 ( )
K1000p
Z0.1u
AIN2
R158
KLATCH 5
C159
R157
R154
AMON
K2200p
KSCLK 8
R55 100 KSCLK (19)
K0.1u
X1 BR2
(20)
C160
R56 100
R155
OPRESET
C162
2 1
OPERST 9
H/L Control
J100p
47K
NC 10
NC
DG
R156 (21)
)
+3.3V/BATIN ( ) A B
NC
J15p
J15p
R57
C51
R58
(
C163
C164
DG
HSTXMUTE
MDMTXEN
TELRXEN
MDMRST
HEADON
PSHORT
DG
Z0.1u
PAPER
C165
PWRCNT
BELL
CPC
JAM
DG
TO POWER (22)
+5V +5V +5VA
+5V FTG
SUPPLY
LEDON
R70 0
FTG
AIN1
F1
Z1u
NC
NC
( )
( )
Q9
C70
C77
(23)
CN1
C71
330K
D503
DG +5V
GND 5
VOUT 1 5
VDD CE
R80
Q11
2 VIN
100K
GND 4
2.2K
VSS 3
R71
Z1u
33K
Z0.1u
Z1u
2
6.3V47u
PG
DG GND
+24V 3 +24V 1
Z0.1u
R77
F36K
3 4 ( )
C75
C74
R74
VOUT VDET
C76
J1
C83
+24V 2
6.3V47u
NC
Z0.1u
C80 Z0.1u
J100p
Z0.1u
C78
C81
BAT1
4.7M
C82
Z0.1u
C87
+24V 1
R73
R79
C73
C79
DG
DG RESET DG DG DG DG
DG
DG DG
(24)
146
KX-FT932FX-B
4M FLASH NC
FOR VOICE
IC6
A[0] 20 A0 D0 21 D[0]
A[1] 19 22 D[1] +5VA
A1 D1
A[2]
A[3]
18
17
A2
A3
D2
D3
23
25
D[2]
D[3]
FAX TX signal +24LV
+24LV
0
A[4] 16 A4 D4 26 D[4] +5VA
A[5] 15 27 D[5]
A5 D5
FAX RX signal
J5
A[6] 14 A6 D6 28 D[6]
A[7] 13 29 D[7] TO ANALOG
A7 D7
A[8] CN2
8
7
6
5
3 A8 +5VA
A[9] 2 A9 RA7 1 +24V
A[10] 31 A10 10K
1
2
3
4
A[11] 1 A11 +3.3VD
J100p
2
R34
A[12] 12
4.7K
WE 7 DG
DG
A12
RBA[0] 4 VDD 8 MDMTXEN
C32
A13 DG 3 +5V
RBA[1] 5 A14 VSS 24 TONE1EN
)
A15 4 PAPER
C106
A16
RBA[4] 6
30
A17
CE
+5VA IC10 +5VA
5 LINETX
32 OE A18 9 1 14
DG VDD 6 TONE1
2.2K
+5VA
R40
2 13
TELRXEN RLY 7 RLY
RBA[5]
R36
4.7K
C114 L12
3 12 HSRXEN CPC 8 CPC
K0.1u
39K
K680p
0 R37
Z0.1u
JAM
IC9 4 11
C116
9 JAM
330K
2.2K
(1) +5VA
J100p
R125
C115
PSHORT 1K
1 V+ 8 5 10
R126
10 P_SHORT
2.2K
R38
4.7K
R129
2 7 6 9 BELL 11 BELL/DCN
C127
R127
DG
A B R39
NC
C112 R131
)
(2) HOOK
C117
+2V 3 6 7 8
K0.033u 3.3K VSS 12 HOOK
C33
C34
DG
L9
(
C113 R123 1K
)
C126
4 V- 5
R128 NC
13 LINERX
D504
100K
J100p
K0.01u
(
K0.01u 0 DG
36K
(3)
R112
14 MONRX
K330p
330K
L10 +2V
C111
K0.1u
47K
R124
(6) 16 H/SRX
L11
DG
0
K0.1u
K0.1u
C110
C125
DG
NC
)
CN10
2.2K
47K
R117 C124
C129
Z0.1u
Q18
R110
R111
R118
( )
( 1 +5V+
( ) ( )
BELL
C123
NC NC NC DG
2 TXD
)
NC
NC
NC
)
TELRXEN 3 RXD
R119
R120
(
(
(7) C120 R113 R115
(
R114
( ) ( ) ( ) ( ) ( )NC PSHORT 4 RTS
NC
NC NC
R116 NC
NC NC
)
)
)
(8) MDMTXEN
NC
Q17
( )
NC
DG DG 5 CTS
ACK_ENR121
C122
(
(
(
C121
HSTXMUTE
TONE2EN
6 DSR
ACK_EN 7 DTR
DG DG
8 GND
DG
+3.3VD
(9) D[7]
D[6]
(10) L18
) NC
L17
L4
L3
( )
22
NC
NC
R227
C224
) NC
R226
R225
Z0.1u
Z0.1u
20K
NC
R231
0
(11)
(
D[0]
( )
16V10u
J12p
J12p
C228 (
C239
Z0.1u
K0.068u
C230
C229
C234 Z0.1u
C227 (
C226
C237
C236
DG
47K
C225
X3
L7
C235
R224
D[5]
0
32.256MHz
R228
D[1] DG
D[4]
Z0.1u
J100p
D[2]
C233
C241 Z0.1u
C240 Z0.1u
R230
R223
69 R229 1K
D[3]
NC
(12)
3.3K
C223 NC
C222 0 K0.22u
)
NC
SPMUTE
51 ( )
C231
68 0
(
80
79
78
77
76
75
74
73
72
71
70
67
66
65
64
63
62
61
60
59
58
57
56
55
54
53
52
R233
(
L6
MDMCS
D505
WRn
RDn
CSn
VDDo77
AVDD
ENABLE_VREG18D
VBG
AVSS
VSSo72
VSS71
VDD70
XTLO
XTLI
TEST
GPI2
GPI1
GPI0
GP02
GPO1
RINGDn
IA1_VDD
IA_AVSS59
IA1_SPKRM
IA1_SPKRP
IA1_TXP
IA1_TXM
IA1_AVDD
IA1_VC
IA1_Vref
IA1_HSMIC_BIAS
NC DG
R201 C220 NC
+3.3VD A[5] ( ) DG
A[4] ( ) 81 SPRn 50
C219 K0.1u
82 A4 49 R221
XTEST A[3] DG
NC
84 A2 IA1_HSMICM 47
(13) A[1] 0 10K
(
NC
C202
R219
(
88 VSSo88 RESERVED43 43 C242 NC
D506
(14)
C201
( )
+3.3VD DG
C203
89 VSS89
90 VDD90 IC5 RESERVED42
RESERVED41
42
41 C243 NC
D[0] Z1u
91 D0 IA_AVSS40 40 ( ) L20
150
RESERVED27
RESERVED28
RESERVED29
RESERVED30
DG
1K
92 D1 RESERVED39 39
D[2] 93 D2 RESERVED38 38
NC
D[3]
NC
NC
R162 1M
R164
94 D3 RESERVED37 37
NC
NC
)
96 D5 RESERVED35 35
)
HOOK D[6] )
12 PIA_CNTRL_SIN
24.00MHz
17 IA1_CNTRL_SIN
(15) 97 D6 RESERVED34 34
D10p
PWRCNT D[7]
23 RESERVED23
25 RESERVED25
26 RESERVED26
C174
C212
C214
9 PIA_STROBE
5 EYEXY/XCLK
21 IA1_STROBE
C173
D10p
6 RESERVED6
7 RESERVED7
8 PIA_RESETn
(
22 IA1_RESETn
C211
C213
98 D7 RESERVED33 33
(
11 PIA_RXOUT
19 IA1_RXOUT
HSRXEN
(
18 IA1_TESTC
10 PIA_TXSIN
13 PIA_CLKIN
16 IA1_CLKIN
20 IA1_TXSIN
14 PIA_SCLK
15 IA1_SCLK
99 RESETn RESERVED32 32
24 IA_AVSS
TONE2EN
NC
NC
)
3 VSSo3
TONE1EN
2 VDD2
1 VSS1
J33p
C215
R218
4.7K
)
NC
DG
+3.3VD
(
(
R232
C209
DG DG
27
28
29
30
(
Z0.1u
C204
C172
C205
Z1u
100
100
100
100
100
100
100
100
)
NC
R215
)
NC
NC
(
R204
DG
NC
R205
R216
R217
C210(
C206
R206
R209
(
R203
(16) DG
R202
Z0.1u
DG
R207
R208
R210
R211
R212
R213
)
NC
C208
DG
(
1K
(17) R178
(18)
(19) R159 R160
(20) 120K 0
)
NC
K1000p
C170
(
2.7K
EYE PATTERN MONITOR
(21) TEST PAD C207
DG DG
K1000p
SPMUTE DG
CISON
AIN1
F1
(22) +3.3VD
R143
R142 10K
TO SPEAKER
22K
3.3K
220
220
2.2K
NC
120K
)
IC12 CN9
C144
(23)
R144
(
1 8
R94
120K
CD VO2 1
R90
SP+
R93
R91
R92
+5V TO +2V
)
2 7
FC2 GND 2 SP-
R146
(
+2V
Q14
R145
+5VA
NC
+2V 3 6
FC1 VCC
50V4.7u
+5V
C142
)
NC
NC
4 5
NC
Q13
VIN VO1
)
)
12K
NC
C141
(
)
NC
10
C145
(
C146
(
D507
R147
(
R75
C143 K1000p
(
NC
1.5K
C90
Z0.1u
R96
R95
C91
NC C93
C140 K0.1u R140 15K R141 9.1K
NC
DG
NC
J100p
)
6.3V47u
)
C92
DG
R76
8.2K
(
C86
C84
C85
(
CN8
LEDVCC
LEDGND
FTG(CLK)
GND
FI(DATA)
AIN(SI)
+3.3V
DG
DG DG
(24)
KX-FT932FX : DIGITAL BOARD SCHEMATIC DIAGRAM
147
KX-FT932FX-B
NC NC
33 1/2W
C55
( )
R65
6.8K
NC
R67
NC
+5V
(
R71 R70
R69
( ) ( )
NC NC NC
NC R68 C60
C NC
A ( )
R10
75K
+24VA
PC4
E K
( ) ( )
NC
R66 NC
D12
NC (2)
Q11
BEAD
+2.0V C8 C56 Q10 12K
C3p
NC
( )
50V10u
L7
J270p
)
NC
NC
R72
C69
(
C54
10K
R2
AG
(3)
T1
C13 R13 56K C17 R81
IC2-1 8 2
300:600
R5 C4
1 K0.039u 4 3
(4)
D10p 0
K0.01u
5.6V
0 3
50V4.7u 2
D2
Z0.1u
4
R18 C21
)
NC
C7
390 1/4W
56K 6 1
K0.039u
C29
4.7V
C63
K0.1u
D1
5.6V
(
R26
BEAD
C26
D3
+12V
L4
R82 0
AG
BEAD
AG
L3
AG
(5)
NC
)
R11 Q13
R87
C27
0
R27
( )
(
75K ( )
NC
(6)
1.8K
R14
)
C9
C66
NC
(
J270p
( )
C18
R22
NC
0
AG AG
(7)
K0.047u
3.6K
C14
R15
K0.01u
3.9K
C19
R23
(8)
AG
C64 NC
+5V
( )
R24 300K R91
50V4.7u
0
+24V C23 J120p
C28
0
L2
C11 R16
CN1 (9)
+24V 1
K0.1u 24K 6
D10p
7
C32 J39p
5
C22
2
AG IC2-2 R39 750K
+5V 3 +2.0V
+5V
AG
PAPER 4
R47
0
L12
LINETX 5
0
C12 R17 R21 C25
TONE1 6
K0.1u 47K 39K K0.022u IC1-1 8 2 (10)
RLY 7 1
)
C35
3 NC
4
(
CPC 8
2.2K
C31
R36
JAM 9 Z0.1u
0
L13
P_SHORT 10
AG
NC
BELL/DCN 11 1K AG
HOOK 12
1A2K ( 2A )
L1 DA2
LINERX 13 (11)
MONRX 14
H/STX_MUTE 15
H/SRX 16
(12)
NC
12K
R28
2 1 2 1
L34 1 4 3 4 3 Q3
JJ5 NC NC
( )
C2
C5 ( )Q4
6.8K
K0.01u K0.01u
R30
+5V +24VA
AG
+24V R34
0
(14)
HOOK SENSOR SW Q1
SW2 L6 0
1 2 3
)
NC
R37
+2.0V
(
10K
NC
)
220K
R25
330K
C16
R31
10K
R19
NCQ5
(
R8
+12V
R1 4 5 6
L5
AG ( )
)
100
NC
35V33u
0
K0.01u
AG
Z0.1u
C71
C24
16V10u
Z0.1u
)
NC
10K
220K
C1
C20
AG AG
C3
(
C15
R20
C6
R9
AG
AG AG AG
148
KX-FT932FX-B
(1)
+5V
+5V
)
R83
)
NC
R77
R86
)
1K
NC
C68
NC
D10
(
C A PC6
NC 2 3
FAX TX signal
)
NC
FAX RX signal
D13
E K
1 4
(
C A PC5 R84 D15
E K
Q12 ( ) (
NC
) (
NC
)
)
C67
R85
NC
NC
)
R88
NC
C53 K680p
(
(
(
Q9
AG
(3) AG
300/310V
CN3
1 4
ZNR1
L19
1 a
2 3
SA1
2 b
R54 NC RLY1 -1
4 L32 POS1
(5) ( )
22 1/4W JJ2
3
(6)
W5NL5T
5
C43
L33
+5V ( ) (PU AT DIGITAL BOARD)
)
NC
JJ3
NC
1 4
R35
( ) PC2
3000V
(
47K 1/2W
(7)
SA2
22K 2 3
NC
R38
C AK
CN4
1 b
PC1
E KA
2 a
D4 D5 R45 L26
(9)
DA1 T3 NC
R48 C50 R61 R62 NC
(10) ( ) ( )
4.7K K0.056u NC
4
() 3
NC
NC
2
)
Q8 1A 2K
)
1
NC 6
(
(
R59
C65
1K2A
R63
1M
+24V
AG AG
R60 C51
(11) RLY1 -2
2
10K K0.1u D8
1
(12) Q7
+5V
C34
R57 L17
J120p
R42 330 0
6.3V47u
1.5K
C47
AG
820K
R55
IC1-2 6
R49 10K C41 K0.027u
AG
7 L23
(13) 5
C36 D10p
8 1
( )
220K
1 HSMIC-
R40
R44
C37
NC
+5V
L14
K0.01u
K0.01u
0
L15
1.5K
C46
C48
R56
R52 7 2
2 HSSP+
22 0 6 3
AG
3 HSSP-
5 4
4 HSMIC+
47K
6.3V47u
R51
( )
L22
0
R58
Q6
C42
C44
NC
L16
C33 R46
L11
L24
(14)
K0.01u
0 18K
C49
K0.1u
D6
D7
K4700p
AG
C39
AG
C45
16V10u
330
R43
AG
AG
149
+5VA +5V +5VA
)
+5V
9 DB6
8 DB5
7 DB4
6 E
5 R/W
4 RS
3 V0
2 VDD
1 VSS
10 DB7
NC
R34
CN2
R47
(
KX-FT932FX-B
( )
C28
R19
4.7
)
NC
)
)
( )
NC
NC
DG AG
NC
NC
C99
(
R35
C25
(
(
R39 TO LCD
( )
C17
Z0.22u
+5V NC
)
R37 C26 AG
( ) ( ) TO MIC
)
NC NC
)
TO DIGITAL Q4 MIC+
(
NC
)
R16
C22
NC
(
CN1
C1
C2
C3
MIC-
Z0.1u
Z0.1u
(
(
6.3V220u
R48
MICIN 1
NC
(
+5V
R17
2.2K
+5V 2
DG 3 AG AG
R1 0
KSTART 4
LED1
R2 0
KLATCH 5
17.3. Operation Board
R14
KRXD 6
R3 0 0
270
R18
KTXD 7
1K
820
R4 0
18K
R24
R25
R15
KSCLK 8
R5 0
OPERST 9
NC 10
)
)
E 25
D7 29
D6 28
D5 27
D4 26
RS 23
C13
C14
+5V
K330p
J120p
TXD 33
RXD 32
RWB 24
SCLK 31
C4
C6
C7
C9
RESET 30
34 LATCH LED1 22
K330p
J120p
K330p
K0.01u
(
(
35 START XLED15 21
36 LED2 XLED14 20
4.7K
R22
37 LED3 XLED13 19
38 LED4 IC1 VSS-18 18
R20 SW39
39 VSS-39 VDD-17 17
40 VDD-40 XLED11 16
4 1
41 LED5 XLED12 15
3 2
100
42 KIN0 KIN7 14
+5VL
C16
43 KSL0 KIN6 13
C19
Z0.1u
44 KSL1 KIN5 12
DOCUMENT
K0.01u
C15
TOP SW
Z0.1u
+5V +5VL
1 KSL2
2 LED6
3 KIN1
4 LED7
5 XLED8
6 XLED9
7 KIN2
8 KIN3
9 XLED10
10 KSL3
11 KIN4
R50
150
33
KSL0
KSL1
KSL2
KSL4
KSL3
+5V
KIN0
KIN1
KIN2
KIN3
KIN4
KIN5
KIN6
KIN7
R23
4.7K
SW38
R21
1 4
KIN0
KIN4
KIN3
KIN2
KIN7
KIN1
KIN6
KIN5
NC 2 3
FAX/START 0 # NAVI LEFT BOARDCAST SKEY 6 ERASE 100
( )
SW1 SW6 SW11 SW16 SW21 SW26 SW31 SW36
C20
K0.01u
KSL0
NC
COPY 7 8 MONITOR NAVI DOWN SKEY 3 MENU PLAYBACK
( )
SW2 SW7 SW12 SW17 SW22 SW27 SW32 SW37
TP1
KSL1
NC CN5
STOP 4 9 PAUSE NAVI UP SKEY 2 AUTO ANSWER RECORD
( )
SW3 SW8 SW13 SW18 SW23 SW28 SW33 SW29
TP2
KSL2
KSL3
KSL4
1000p
0V
0V
T101 TRANS
C202 1000p/1k
/1k
R107
1000p
100k/2 CN202
D105 C108
R106 C107 D202
1 24V
D102 D101
47/2 47p/1k
17.4. Power Supply Board
1k
5.6k
R224
R221
2 24V
L103
C106
Q101
56/450
5k
1k
VR201
3 24V
R222
R223 C205
PC101
10 S
C201
10k
220/35
R105 Q203 1k 0.1/25 4 GND
R121
(R202)
18k
R229
0.22/2
C102 R225 5 GND
2.2k
1k
D110
R228
D205
(R206)
0.1 D206
6 GND
100
R123 R122
R128
D109
C105
3300p
(Q202) Q201
151
10k
C103 1.8K 180 0V
R102
7 6V
D204
(C207)
1000p 4 5 8 6V
C121 R111 D106 D202 (C208) (R227)
L101 3 6 9 P-Cont
4700p IC101 22
2 7
ZNR101 PC101
0.1
1 8
C203
470/16
(D203)
C123
C109
47/35
750V
0.01
C124
25
0.1
R101
C122
1M 1/2
C101
0V 0V
0.1
F101
250V
T3.15A
GND
1
L N
CN31
MEMO:
152
2 1
+5VA
CN1 J1
CN8 CN9
1
C84
R75
9 1 7 C85
R10 C73
18.1. Digital Board
5 4
L10 C86
C116 R76
1
Q7
R143
R127
1
8 L12
X1 32.7
18.1.1. Component View
C11
C144
C10
C115
8 1
R146
C72
16
Q14
F1
C90
C74 E R92 R128
R1
R126
C117
E Q2
4
5
C92
C71
C77
R142
Q1 E
IC12
R93 L9
R91
IC15 R125 C114
L11
C75
R70
R96
C141
R2 D507
C12
C76
C91
C70 1 4
18 Printed Circuit Board
CN4
C213
C93
R90
1 5 R159 C214
D502 TEST C212
C80 C227
C169
C79
E C142
R157
R178
C78
IC3 C211
D501
R3
X2
Q13
R207
C170 R160
9 8 3 C81 DG C228
CN2
R71 4 R211
C82
R210
R213
R209
R208 C235
REF-CH 32 17 PCB-CH
153
R72 E R203
R212
C234 R227 L18
11
C83
R74
R73 Q10
R101
1 28
8
7
1 AUTO-CH
IC7
C31
R32
R33
C101
32 IC10
C102
R229
IC6
CN3
2 1 2 1 17
X3
C236 B
CN5 CN6
14
1
C237 C94
IC4
1
C100
5 L7
16 RA7
IC2
16 1 1
F2
PbF
0.25A
YELLOW BLUE R100
C104
C129
R172 8 1 A
C106
10 1
14 15
1 16
C103 CN10
CN206 J2
PFUP1546Z A
+5VA
E
PbF
Q16
R12
R145
AMON
Q6 1
C164
R156 Q9
Q11
R141
C118
C143
C163 C166
A B
C158
C119 R13 Q5 Q4
C111
C128 R140 E E
D506 +3.3V/BATIN +3.3VD
R153
R124 R112 +2.5V/BATIN
C165
C113
R155
C160
C162
R14
R123 C168
C159
R219 R111 C171 36 +2V FTG 1
D504
C216 R221
C13
C161
C14
R216 XMI
L20
R158
R220
C167
R130 C208
R18
C220
C219 C231
C217
R164
D505
R217
C210
37
ADR13
C156
ADR15
L19
CN4
R15
R218
C215
R38 C155 R154
C209
R224
C172
R17
C173
C222
R215
R152
R223
R222
C34
R162
C221 PG
9
R163
C226 30
R58
C33
R16
C223 XTEST R57
154
CN2
C229
C230
C174
R37
R225
R36
C175
R214 IC1 C154
C225
R40 R226
C207
+2.5VD
C224 C232 R165 R167 R151
R35
C32
L17 11
IC5
EYECLK R166
R228
C233 1
109 XRESET C30
R31
R204 IC7
R230
R34
C153
R205
C238 D4 D5 C151
R206
CN3
J5 R30
R117
C176
C239 R202 D3 73 108
C177 A4
C240
C178
R116
C121
R231
RD
C150
A16
R150
C179
L3 XCLK/EYEXY A12
EYESYNC 5
R115 R120 C241 80 A3 A10 A6
A14
R119 1 C206 R51
C205
C123
R52
R118
A11
RBA6
L4 ROMCS A7 R55
C204
R121 100 D2 A0
C203
C124 C50
A18
L6 C51
R56
R114 D7
16
C122 Q18 A2 WR A8
C201
C202
R59
Q17
1 7
1
5
R54 R53
R201
C200 R232
IC11
R200
A13
A1
A17
D6 MFCS C105 +5V
D1
3
4
C120
R113
A15
18.1.2. Bottom View
CN10 A5 D0
R102 +24LV
1 CN206 10
CE2
CE1 A9
2 8
A PFUP1546Z
KX-FT932FX-B
JJ2
R41
L19 CN4 CN3
ZNR1
CN2
JJ1
JJ4
JJ3
RLY1
D13 R86
R54
C52
C68
D8 D15 POS1
R9
R67
C67
18.2.1. Component View
C53
Q10
18.2. Analogue Board
E SA1 SA2
C38
L33
C54
D3 R38
PC6
PC2
1 FLT3
SW2
4
D12
R62
D2
C28
T1
SW1
R45
J28
C56
J26
D5
D4
8 J30
J2
155
5
JJ5
T3
PC5
PC1
PC4
D6 C4
J18
J20
J24
C45
J21
PFUP1547Z
C42
D7 SW3
D1
J6
J17
J3 J29
C15
J10
C47 J4
J22
R26
R27
J15
J27
C71
PbF
PCB-CH
J16
AUTO-CH
J25
J19
C10 C6 J14
J13
J11
J8
J11 J7 1 16
CN1
A
KX-FT932FX: Analog Board (Component View)
KX-FT932FX-B
KX-FT932FX-B
1
L34 R8 16
R47 R2 CN1
C72
DA2
L14
R9
R30
C3 R39 R60 L2
R25 R5 R34
+2V C32 R33 L11
L13
L1
R48
R28
R36
R31
C33
Q3
C16
C37 R44 C35 R29
R46
E
C25
18.2.2. Bottom View
L17
C31
L12 R37
5
4
Q2
Q1
C11
E
E
R49 C36 C24
Q4
PFUP1547Z
R50
R21
C34 C12
IC1
E
C40
R16
R42 C30 R17
C20
R19
1
Q5
E
Q9
8
R57 R32 L10 C50 Q8 +24VA
R72
E
R40 C51 L6
C48 C46
L16 R20 L5 R51
R56 R55
C39
Q6
R43
L15
R77
C41
PbF
E R52
C26
C44 C27
R61 L4 C14 C5
C49 L3 C22
R11
R15
+12V
PC1
PC5
PC4
C23 C64
E K
C A
DA1
C9
K E
C7
A C
E KA
C AK
R81
R35 R24 R91
4
C17
5
R63 L7
R13 R14 R82
C13
IC2
C65 C21 C18
R65
156
R59 Q13 C8 R23 R22
8
L23 C60 1
R58 R10 C19
E
L21 L24 L22 C1 R18 C2
R71 C66 R1
R70
C29
R87
R88
E
3
4
Q11
PC6
PC2
R66
E K
C A
2
1
C63
E
C69
Q7
R69 R83
C55 C43
R84
R68
E
R85
Q12
L31
L26
EXT.LINE
LINE
L32
D10
L25
A
KX-FT932FX: Analog Board (Bottom View)
1 10 A
CN2
PFUP1560Z PbF SW29 SW36 SW37 SW33
18.3.1. Component View
LED1
18.3. Operation Board
J15
J26
J3
J13 J6
J14 SW30 S1 J2 SW35 S4
J5
J4
CALLER ID J12 J7 J1
SW5 SW28 S2 SW34 S5
FLASH
J11
J10
SW4 1 SW9 2 SW14 3 SW19
SW27 S3 SW31 S6
157
STOP PCB-CH REDIAL
J16
SW3 SW8 4 SW10 5 SW15 6 SW20
J8
J9
PAUSE
COPY BROADCAST SW23 MENU
SW7 7 SW12 8 SW13 9
J17 SW18
J20
FAX/START SW2
C3
SW21 SW25 SW24
SW1 J35
1 10
SW6 * SW11 0 SW16 # SW17
SW22
CN1
MONITOR
Q4
E
C25 R48
R37
R47 C28 C26
R39
R34
R35 C22
SW38
R21
C20 R23
R17
C17
1
R19
R16
R15
R25
R24
10
PbF
R22
1
SW39
R20
C19 C1
PFUP1560Z
R1
R2
10
C2 R3
R4
R5
C15 R50
1
44
C4
C9
IC1
12 11
33 34
R14
C13
C16 C7
C14
22
23
C6
R18
1 JP201 9 C205
SECONDARY
VR201
R223
C201
JP203
D203
R225
D206
C207
JP202
D201
C208
C203
C202
D202
D204
R227
R226
J204
R202 Q202
D205
D205
Q203
PbF R228 Q201
R229 R221
R222
T101
SECONDARY
C110
PC101
SRF 1678EK PRIMARY
PRIMARY C214
D105
C108
(COMPONENT VIEW)
L103
C107
R106
D106
(BOTTOM VIEW)
R107
Q101
JP103
R111
R122
C109
R105 R121 R128
D109
JP102 C123
R109 R123
5
C121
IC101
R102
C106
C122
8
JP101
D103
D104
D110
D102
SEE SOLDER SIDE
D101
C105
L101
C102 CAUTION FOR CONTINUED
C101
Blue
ZNR101
F101
C103
R101
N
Brown
L
CN31
159
KX-FT932FX-B
3.
160
KX-FT932FX-B
161
KX-FT932FX-B
162
KX-FT932FX-B
163
KX-FT932FX-B
164
KX-FT932FX-B
20.1.5. Screws
165
KX-FT932FX-B
166
KX-FT932FX-B
167
KX-FT932FX-B
20.3.4. Gear Block Section Ref. Part No. Part Name & Description Remarks
No.
IC4 C3ABKC000034 IC
Ref. Part No. Part Name & Description Remarks IC5 C1CB00001959 IC
No. IC7 B1HAGFF00015 IC
150 PFDG1447Z GEAR,TX4 IC9 C0ABEB000052 IC
151 PFDG1444Z GEAR,TX1 IC10 C0JBAS000252 IC
152 PFDG1446Z GEAR,TX3 IC11 C0JBAA000474 IC
153 PFDG1445Z GEAR,TX2 IC12 C1BB00000129 IC
154 PFDG1442Z GEAR,DOC2 IC15 C0CBADD00009 IC
155 PFDE1259Z ARM
156 PFDG1441Y GEAR,DOC1 (TRANSISTORS)
157 PFUS1579Z SPRING Q1 2SB1322 TRANSISTOR(SI) S
158 PFDG1448Z GEAR,CAM Q2 PQVTDTC143E TRANSISTOR(SI) S
159 PFUS1591Z SPRING Q4 PQVTDTC143E TRANSISTOR(SI) S
160 PFDG1438Z GEAR, D Q5 PQVTDTC143E TRANSISTOR(SI) S
161 PFUS1231Y SPRINT, GEAR 1 Q6 PQVTDTC143E TRANSISTOR(SI) S
162 PFHR1500Z ARM4 Q7 B1DHDD000026 TRANSISTOR(SI)
163 PFHR1497Y ARM1 (Black) Q9 PQVTDTC143E TRANSISTOR(SI) S
164 PFHR1498Z ARM2 Q10 B1ABDF000025 TRANSISTOR(SI)
165 PFDG1436Z GEAR, B Q11 B1ABDF000025 TRANSISTOR(SI)
166 PFDG1443Z GEAR, RX Q13 B1ABDF000025 TRANSISTOR(SI)
167 Not Used Q14 2SB1218ARL TRANSISTOR(SI)
168 Not Used Q16 B1ABDF000025 TRANSISTOR(SI)
169 PFDG1435Z GEAR, A
170 Not Used (BATTERY)
171 Not Used BAT1 BR2032/1HF1 BATTERY S
172 Not Used
173 PFMH1171Z COVER (DIODES)
174 Not Used D501 PFVDRMRLS245 DIODE(SI) S
175 Not Used D502 MAZ720000F DIODE(SI)
176 Not Used D503 PFVDRMRLS245 DIODE(SI) S
177 PQST2A04Z SENSOR, MOTOR D504 MA729 DIODE(SI) S
178 PFHR1488Y COVER, GEAR BASE (Black)
179 PFUA1066Y GEAR BASE (CAPACITORS)
180 L6HAGCLK0008 MOTOR C10 ECJ1VB1C104K 0.1
181 Not Used C12 ECJ1VF1C104Z 0.1
182 Not Used C13 ECJ1VC1H101J 100P
183 PFJS03Q43Y CONNECTOR for CAM SENSOR C14 ECJ1VC1H101J 100P
184 Not Used C30 ECJ1VC1H101J 100P
185 Not Used C31 ECJ1VC1H101J 100P
C32 ECJ1VC1H101J 100P
20.3.5. Accessories and packing materials C33 ECJ1VC1H101J 100P
C34 ECJ1VB1C103K 0.01
C50 ECJ1VF1C104Z 0.1
Ref. Part No. Part Name & Description Remarks C51 ECJ1VC1H101J 100P
No. C71 ECJ1VF1A105Z 1
A1 PFJA02B002Y CORD, TELEPHONE C72 F2G1C2210008 220
A2 PQJA212V CORD, HANDSET C73 ECJ1VF1H104Z 0.1
A3 PFHP1123Z SHEET PAPER RECORDING PAPER C74 ECJ1VF1A105Z 1
(10M)
C75 F2G0J4700032 47
A4 Not Used
C76 ECJ1VF1A105Z 1
A5 PFQX2588Z INSTRUCTION BOOK
C78 F2G0J4700032 47
A6 PFJXH0901Z HANDSET ASS'Y
C79 ECJ1VF1H104Z 0.1
A7 PFHP1145Z SHEET PAPER
C80 ECJ1VF1H104Z 0.1
C81 ECJ1VC1H101J 100P
P1 PFZE1632Z-M GIFT BOX
C82 ECJ1VF1C104Z 0.1
P2 PFPN1405Z CUSHION
C83 ECJ1VF1C104Z 0.1
P3 PFPN1406Z CUSHION
C85 F2G0J4700032 47
P4 PFPD1277Z CUSHION
C87 ECJ1VF1C104Z 0.1
P5 PFPH1085Z PACKING SHEET
C90 ECJ1VF1C104Z 0.1
P6 PQPP10005Z PROTECTION COVER
C92 ECJ1VC1H101J 100P
P7 XZB20X35A04 PROTECTION COVER
C94 ECJ1VF1E104Z 0.1
C102 ECJ1VF1C104Z 0.1
20.4. Digital Board Parts C103 ECJ1VF1C104Z 0.1
C104 ECJ1VF1C104Z 0.1
C105 ECJ1VF1C104Z 0.1
Ref. Part No. Part Name & Description Remarks C110 ECJ1VB1C104K 0.1
No.
C111 ECJ1VB1H331K 330P
PCB1 PFWP1FT932FX DIGITAL BOARD ASS'Y (RTL)
C112 ECJ1VB1C333K 0.033
C113 ECJ1VB1C103K 0.01
(ICs)
C114 ECJ1VB1C104K 0.1
IC1 C1ZBZ0001896 IC
C115 ECJ1VB1H681K 680P
IC2 PFWIFT932FX IC
C116 ECJ1VF1C104Z 0.1
IC3 C0CBCBD00047 IC
C118 ECJ1VB1C104K 0.1
168
KX-FT932FX-B
Ref. Part No. Part Name & Description Remarks Ref. Part No. Part Name & Description Remarks
No. No.
C125 ECJ1VB1C104K 0.1 F1 K5H122200005 FUSE
C127 ECJ1VC1H101J 100P F2 K5H251200003 FUSE
C128 ECJ1VB1C104K 0.1
C129 ECJ1VF1E104Z 0.1 (COILS)
C140 ECJ1VB1C104K 0.1 L3 PQLQR2KA113 COIL S
C142 F2G1H4R70017 0.1 S L4 PQLQR2KA113 COIL S
C143 ECJ1VB1H102K 0.001 L6 PQLQR2KA20T COIL S
C150 ECJ1VC1H101J 100P L7 J0JCC0000042 COIL
C151 ECJ1VF1C104Z 0.1 L17 PQLQR2KA20T COIL S
C153 ECJ1VF1C104Z 0.1 L18 PQLQR2KA20T COIL S
C154 ECJ1VF1C104Z 0.1 L21 PQLQR2KA113 COIL S
C155 ECJ1VF1C104Z 0.1 R203 PQLQR2KA20T COIL S
C156 ECJ1VF1C104Z 0.1 R204 PQLQR2KA20T COIL S
C157 ECJ1VF1C104Z 0.1 R208 PQLQR2KA20T COIL S
C158 F1J1A4750003 4.7M R209 PQLQR2KA20T COIL S
C159 ECJ1VB1H102K 0.001
C160 ECJ1VB1H222K 0.0022 (RESISTORS)
C161 ECJ1VB1C104K 0.1 J5 ERJ3GEY0R00 0
C162 ECJ1VB1C104K 0.1 L9 ERJ3GEY0R00 0
C163 ECJ1VC1H150J 15P L10 ERJ3GEY0R00 0
C164 ECJ1VC1H150J 15P L11 ERJ3GEY0R00 0
C165 ECJ1VF1C104Z 0.1 L12 ERJ3GEY0R00 0
C167 ECJ1VF1C104Z 0.1 R1 ERJ3GEYJ821 820
C168 ECJ1VB1H102K 0.001 R2 D0GN152JA016 1.5K
C169 ECJ1VB1H102K 0.001 R3 ERJ3GEYJ221 220
C171 ECJ1VF1C104Z 0.1 R10 ERJ3GEYJ562 5.6K
C172 ECJ1VF1C104Z 0.1 R11 ERJ3GEYJ222 2.2K
C173 ECJ1VC1H100D 10P R12 ERJ3GEYJ472 4.7K
C174 ECJ1VC1H100D 10P R13 ERJ3GEYJ101 100
C175 ECJ1VF1C104Z 0.1 R14 ERJ3GEYJ101 100
C176 ECJ1VF1C104Z 0.1 R15 ERJ3GEYJ101 100
C177 ECJ1VF1C104Z 0.1 R16 ERJ3GEYJ101 100
C178 ECJ1VF1C104Z 0.1 R17 ERJ3GEYJ101 100
C179 ECJ1VF1C104Z 0.1 R30 ERJ3GEYJ472 4.7K
C201 ECJ1VB1H472K 0.0047 R31 ERJ3GEYJ102 1K
C202 ECJ1VF1C104Z 0.1 R32 ERJ3GEYJ102 1K
C203 ECJ1VF1A105Z 1 R33 ERJ3GEYJ472 4.7K
C204 ECJ1VC1H330J 33P R34 ERJ3GEYJ472 4.7K
C205 ECJ1VF1A105Z 1 R35 ERJ3GEYJ102 1K
C206 ECJ1VF1C104Z 0.1 R36 ERJ3GEYJ472 4.7K
C207 ECJ1VB1H102K 0.001 R37 ERJ3GEYJ102 1K
C216 ECUV1C224KBV 0.22 R38 ERJ3GEYJ472 4.7K
C217 ECJ1VB1C104K 0.1 R39 ERJ3GEYJ102 1K
C219 ECJ1VB1C104K 0.1 R40 ERJ3GEYJ222 2.2K
C221 ECUV1C224KBV 0.22 R51 ERJ3GEYJ271 270
C222 ECJ1VB1C104K 0.1 R52 ERJ3GEYJ271 270
C225 ECJ1VB1C683K 0.068 R53 ERJ3GEYJ101 100
C226 ECJ1VF1C104Z 0.1 R54 ERJ3GEYJ101 100
C229 ECJ1VF1C104Z 0.1 R55 ERJ3GEYJ101 100
C232 ECJ1VC1H101J 100P R56 ERJ3GEYJ101 100
C233 ECJ1VF1C104Z 0.1 R57 ERJ3GEYJ473 47K
C234 ECJ1VF1C104Z 0.1 R59 ERJ3GEYJ472 4.7K
C235 F2G1C1000014 10 R70 ERJ3GEY0R00 0
C236 ECJ1VC1H120J 12P R71 ERJ3GEYJ333 33K
C237 ECJ1VC1H120J 12P R72 ERJ3EKF1101 1.1K
C238 ECJ1VF1A105Z 1 R73 ERJ3EKF3602 36K
C239 ECJ1VF1C104Z 0.1 R74 ERJ3GEYJ104 100K
C240 ECJ1VF1C104Z 0.1 R75 ERJ3GEYJ123 12K
C241 ECJ1VF1C104Z 0.1 R76 ERJ3GEYJ822 8.2K
R78 ERJ3GEYJ334 330K
(CONNECTORS) R79 ERJ3GEYJ475 4.7M
CN1 K1KA09A00204 CONNECTOR, 9 PIN R80 ERJ3GEYJ222 2.2K
CN2 K1KA16A00206 CONNECTOR, 16 PIN R90 ERJ3GEYJ332 3.3K
CN3 K1KA05AA0193 CONNECTOR, 5 PIN R91 ERJ3GEYJ221 220
CN4 K1KA11A00158 CONNECTOR, 11 PIN R92 ERJ3GEYJ221 220
CN5 K1KA02A00746 CONNECTOR, 2 PIN R93 ERJ3GEYJ222 2.2K
CN8 K1KA07A00257 CONNECTOR, 7 PIN R94 ERJ3GEYJ223 22K
CN9 K1KA02A00587 CONNECTOR, 2 PIN R95 ERJ3GEYJ152 1.5K
CN10 K1MN08A00017 CONNECTOR, 8 PIN R96 ERJ3GEYJ100 10
CN206 K1KA10A00412 CONNECTOR, 10 PIN R100 ERJ3GEYJ103 10K
R101 ERJ3GEYJ103 10K
R102 ERJ3GEYJ103 10K
(FUSES) R110 ERJ3GEYJ222 2.2K
169
KX-FT932FX-B
Ref.
No.
Part No. Part Name & Description Remarks 20.5. Analog Board Parts
R111 ERJ3GEYJ473 47K
R112 ERJ3GEYJ334 330K
Ref. Part No. Part Name & Description Remarks
R123 ERJ3GEYJ104 100K
No.
R124 ERJ3GEYJ473 47K
PCB2 PFLP1754FXZ ANALOG BOARD ASS'Y (RTL)
R125 ERJ3GEYJ222 2.2K
R126 ERJ3GEYJ393 39K
(ICs)
R127 ERJ3GEYJ334 330K
IC1 C0ABEB000083 IC S
R128 ERJ3GEYJ363 36K
IC2 C0ABEB000075 IC S
R129 ERJ3GEYJ222 2.2K
R130 ERJ3GEYJ243 24K
(TRANSISTORS)
R131 ERJ3GEYJ332 3.3K
Q1 B1ABDF000025 TRANSISTOR(SI)
R140 ERJ3GEYJ153 15K
Q2 B1GBCFJJ0047 TRANSISTOR(SI)
R141 ERJ3GEYJ912 9.1K
Q3 B1GBCFJJ0047 TRANSISTOR(SI)
R142 ERJ3GEYJ103 10K
Q6 B1ABDF000026 TRANSISTOR(SI)
R143 ERJ6GEY0R00 0
Q7 PQVTDTC143E TRANSISTOR(SI) S
R144 ERJ3GEYJ124 120K
Q8 PQVTDTC143E TRANSISTOR(SI) S
R145 ERJ3GEYJ124 120K
Q9 PQVTDTC143E TRANSISTOR(SI) S
R150 ERJ3GEYJ222 2.2K
Q10 B1AAKL000008 TRANSISTOR(SI)
R151 ERJ3GEYJ472 4.7K
R152 ERJ3GEYJ223 22K
(DIODES)
R153 ERJ3GEYJ100 10
D1 MA4047 DIODE(SI) S
R154 ERJ3GEYJ473 47K
D2 MA4056 DIODE(SI) S
R155 ERJ3GEYJ223 22K
D3 MA4056 DIODE(SI) S
R157 ERJ3GEYJ101 100
D4 MA4056 DIODE(SI) S
R158 ERJ3GEYJ471 470
D5 MA4056 DIODE(SI) S
R159 ERJ3GEYJ124 120K
D6 B0EAAD000001 DIODE(SI)
R160 ERJ3GEY0R00 0
D7 B0EAAD000001 DIODE(SI)
R161 ERJ3GEYJ101 100
D8 B0EAAD000001 DIODE(SI)
R162 ERJ3GEYJ105 1M
D10 B0EDER000009 DIODE(SI)
R163 ERJ3GEYJ151 150
D12 B0EAAD000001 DIODE(SI)
R164 ERJ3GEYJ102 1K
R165 ERJ3GEYJ101 100
(JACKS AND CONNECTOR)
R166 ERJ3GEYJ100 10
CN1 PQJS16A10Z CONNECTOR, 16 PIN S
R167 ERJ3GEYJ100 10
CN2 K2LA1YYB0001 JACK
R172 ERG2SJ681 680
CN3 K2LB1YYB0002 JACK
R178 ERJ3GEYJ102 1K
CN4 K2LB1YYB0002 JACK
R200 ERJ3GEY0R00 0
R202 ERJ3GEYJ101 100
(SWITCHES)
R205 ERJ3GEYJ101 100
SW1 PFSH1A03Z PUSH SWITCH S
R206 ERJ3GEYJ101 100
SW2 K0L1KA000007 PUSH SWITCH
R207 ERJ3GEYJ101 100
SW3 PFSH1A03Z PUSH SWITCH S
R210 ERJ3GEYJ101 100
R211 ERJ3GEYJ101 100
(COILS)
R212 ERJ3GEYJ101 100
L1 PQLQR2KA113 COIL S
R213 ERJ3GEYJ101 100
L3 PQLQR2KA113 COIL S
R214 ERJ3GEYJ272 2.7K
L4 PQLQR2KA113 COIL S
R219 ERJ3GEYJ103 10K
L7 PQLQR2KA113 COIL S
R220 ERJ3GEY0R00 0
L10 PQLQR2KA113 COIL S
R221 ERJ3GEYJ472 4.7K
L19 PFLE003 COIL S
R222 ERJ3GEY0R00 0
L21 PQLQR2KA113 COIL S
R223 ERJ3GEYJ392 3.9K
L22 PQLQR2KA113 COIL S
R224 ERJ3GEY0R00 0
L23 PQLQR2KA113 COIL S
R226 ERJ3GEYJ203 20K
L24 PQLQR2KA113 COIL S
R227 PQ4R18XJ220 22 S
L25 PQLQR2BT COIL S
R228 ERJ3GEYJ473 47K
L26 PQLQR2BT COIL S
R229 ERJ3GEYJ102 1K
L31 PQLQR2BT COIL S
R230 ERJ3GEY0R00 0
L32 PQLQR2BT COIL S
R231 ERJ3GEY0R00 0
R232 ERJ3GEYJ472 4.7K
(PHOTO ELECTRIC TRANSDUCERS)
R233 ERJ3GEYJ332 3.3K
PC1 B3PAA0000330 PHOTO ELECTRIC TRANSDUCER
PC5 PQVIPS2532-1 PHOTO ELECTRIC TRANSDUCER S
(COMPONENTS PARTS)
RA7 EXB38V103JV COMPONENTS PARTS
(THERMISTOR)
POS1 PFRT002 THERMISTOR S
(CRYSTAL OSCILLATORS)
X1 H0A327200096 CRYSTAL OSCILLATOR
(RELAY)
X2 H2A240500005 CRYSTAL OSCILLATOR
RLY1 PFSL003Z RELAY S
X3 H0J322500004 CRYSTAL OSCILLATOR
(TRANSFORMER)
T1 G4A1A0000170 TRANSFORMER
(VARISTORS)
SA1 PQVDDSS301L VARISTOR S
170
KX-FT932FX-B
Ref. Part No. Part Name & Description Remarks Ref. Part No. Part Name & Description Remarks
No. No.
SA2 J0LS00000024 VARISTOR R91 ERJ3GEY0R00 0
ZNR1 ERZVA7D121 VARISTOR
(CAPACITORS)
(RESISTORS) C1 ECJ1VB1H103K 0.01
L2 ERJ3GEY0R00 0 C2 ECJ1VB1H103K 0.01
L5 ERJ3GEY0R00 0 C4 ECEA1HKA4R7 4.7 S
L6 ERJ3GEY0R00 0 C5 ECJ1VB1H103K 0.01
L11 ERJ3GEY0R00 0 C6 ECEA0JKA470 47 S
L12 ERJ3GEY0R00 0 C7 ECJ1VF1E104Z 0.1
L13 ERJ3GEY0R00 0 C8 ECJ1VC1H271J 270P
L14 ERJ3GEY0R00 0 C9 ECJ1VC1H271J 270P
L15 ERJ3GEY0R00 0 C11 ECJ1VB1C104K 0.1
L16 ERJ3GEY0R00 0 C12 ECJ1VB1C104K 0.1
L17 ERJ3GEY0R00 0 C13 ECJ1VC1H100D 10P
L34 ERJ6GEYJ1R0 0 C14 ECJ1VB1C473K 0.047
C15 F2A1C1000030 10
R1 ERJ3GEYJ101 100 C17 ECJ1VB1C393K 0.039
R2 ERJ3GEYJ103 10K C19 ECJ1VB1H103K 0.01
R5 ERJ3GEY0R00 0 C20 ECJ1VF1E104Z 0.1
R8 ERJ3GEYJ103 10K C21 ECJ1VB1C393K 0.039
R9 ERJ3GEYJ103 10K C22 ECJ1VC1H100D 10P
R10 ERJ3GEYJ753 75K C23 ECJ1VC1H121J 120P
R11 ERJ3GEYJ753 75K C24 ECJ2VF1H104Z 0.1
R13 ERJ3GEYJ563 56K C25 ECJ1VB1C223K 0.022
R14 ERJ3GEYJ182 1.8K C26 ECJ1VB1C104K 0.1
R15 ERJ3GEYJ362 3.6K C28 ECEA1HKA4R7 4.7 S
R16 ERJ3GEYJ243 24K C29 ECJ1VB1H103K 0.01
R17 ERJ3GEYJ473 47K C30 ECJ1VB1C104K 0.1
R18 ERJ3GEYJ563 56K C31 ECJ1VF1E104Z 0.1
R19 ERJ3GEYJ224 220K C32 ECJ1VC1H390J 39P
R20 ERJ3GEYJ224 220K C33 ECJ1VB1C104K 0.1
R21 ERJ3GEYJ393 39K C34 ECJ1VC1H121J 120P
R22 ERJ3GEY0R00 0 C36 ECJ1VC1H100D 10P
R23 ERJ3GEYJ392 3.9K C38 F0C2E105A146 1
R24 ERJ3GEYJ304 300K C39 ECJ1VB1H472K 0.0047
R25 ERJ3GEYJ103 10K C40 ECJ1VB1C273K 0.027
R26 ERDS2TJ391 390 S C41 ECJ1VB1C273K 0.027
R28 ERJ3GEYJ123 12K C42 ECEA0JKA470 47 S
R29 ERJ3GEYJ562 5.6K C45 F2A1C1000030 10
R30 ERJ3GEYJ682 6.8K C46 ECJ1VB1H103K 0.01
R31 ERJ3GEYJ334 330K C47 ECEA0JKA470 47 S
R32 ERJ3GEYJ363 36K C48 ECJ1VB1H103K 0.01
R34 ERJ3GEY0R00 0 C49 ECJ1VB1H103K 0.01
R35 ERJ3GEYJ223 22K C50 ECJ1VB1C563K 0.056
R36 ERJ3GEYJ222 2.2K C51 ECJ1VB1C104K 0.1
R38 ERDS1TJ473 47K S C52 ECKD2H681KB 680P S
R39 ERJ3GEYJ754 750K C53 ECKD2H681KB 680P S
R40 ERJ3GEYJ222 2.2K C54 ECEA1HKS100 10 S
R41 ECEA1HKN2R2 2.2 C69 ECJ1VC1H030C 3P
R42 ERJ3GEYJ824 820K C71 ECEA1VKA330 33
R43 ERJ3GEYJ331 330 C72 F1J1H104A578 0.1
R44 ERJ3GEYJ224 220K
R45 ERDS1TJ223 22K S 20.6. Operation Board Parts
R46 ERJ3GEYJ183 18K
R47 ERJ3GEY0R00 0
R48 ERJ3GEYJ472 4.7K Ref. Part No. Part Name & Description Remarks
R49 ERJ3GEYJ103 10K No.
R50 ERJ3GEYJ103 10K PCB3 PFWP2FT932CN OPERATION BOARD ASS'Y (RTL)
R51 ERJ3GEYJ473 47K PCB3-1 K0L1BA000095 SWITCH (SW38)
R52 ERJ3GEYJ220 22 PCB3-2 K0L1AA000002 SWITCH (SW39)
R54 ERDS2TJ220 22 S
R55 ERJ3GEYJ152 1.5K (IC)
R56 ERJ3GEYJ152 1.5K IC1 C1ZBZ0002089 IC
R57 ERJ3GEYJ331 330
R58 ERJ3GEY0R00 0 (DIODE)
R60 ERJ3GEYJ103 10K LED1 LNJ801LPDJA LED
R63 ERJ3GEYJ105 1M
R65 ERJ3GEYJ682 6.8K (CONNECTOR)
R66 ERJ3GEYJ123 12K CN1 K1KA10B00215 CONNECTOR,10 PINS
R67 ERDS1TJ330 33 S
R77 ERJ3GEYJ102 1K (LIQUID CRYSTAL DISPLAY)
R81 ERJ3GEY0R00 0 CN2 L5DAAFB00001 LIQUID CRYSTAL DISPLAY
R82 ERJ3GEY0R00 0 S
171
KX-FT932FX-B
Ref. Part No. Part Name & Description Remarks Ref. Part No. Part Name & Description Remarks
No. No.
(SWITCHES) S C15 ECJ1VB1C105K 1
SW1 EVQ11Y05B SPECIAL SWITCH S C16 ECJ1VB1C105K 1
SW2 EVQ11Y05B SPECIAL SWITCH S C17 ECJ1VB1C105K 1
SW3 EVQ11Y05B SPECIAL SWITCH S C19 ECJ1VB1H103K 0.01
SW4 EVQ11Y05B SPECIAL SWITCH S C20 ECJ1VB1H103K 0.01
SW5 EVQ11Y05B SPECIAL SWITCH S C31 ECJ1VB1H152K 0.0015
SW6 EVQ11Y05B SPECIAL SWITCH S C32 ECJ1VB1H152K 0.0015
SW7 EVQ11Y05B SPECIAL SWITCH S C33 ECJ1VB1H272K 0.0027
SW8 EVQ11Y05B SPECIAL SWITCH S C34 ECJ1VF1E104Z 0.1
SW9 EVQ11Y05B SPECIAL SWITCH S C35 ECJ1VF1E104Z 0.1
SW10 EVQ11Y05B SPECIAL SWITCH S
SW11 EVQ11Y05B SPECIAL SWITCH S 20.7. Power Supply Board Parts
SW12 EVQ11Y05B SPECIAL SWITCH S
SW13 EVQ11Y05B SPECIAL SWITCH S
SW14 EVQ11Y05B SPECIAL SWITCH S Ref. Part No. Part Name & Description Remarks
SW15 EVQ11Y05B SPECIAL SWITCH S No.
SW16 EVQ11Y05B SPECIAL SWITCH S PCB4 N0AC2GJ00005 POWER SUPPLY BOARD ASS'Y
(RTL)
SW17 EVQ11Y05B SPECIAL SWITCH S
SW18 EVQ11Y05B SPECIAL SWITCH S
(ICs)
SW19 EVQ11Y05B SPECIAL SWITCH S
IC101 PFVIFA5518N IC S
SW20 EVQ11Y05B SPECIAL SWITCH S
SW21 EVQ11Y05B SPECIAL SWITCH S
(TRANSISTORS)
SW22 EVQ11Y05B SPECIAL SWITCH S
Q101 2SK2647 TRANSISTOR(SI)
SW23 EVQ11Y05B SPECIAL SWITCH S
Q201 DTA114EKAT46 TRANSISTOR(SI)
SW24 EVQ11Y05B SPECIAL SWITCH S
Q203 2SC3928 TRANSISTOR(SI)
SW25 EVQ11Y05B SPECIAL SWITCH S
SW26 EVQ11Y05B SPECIAL SWITCH S
(DIODES)
SW27 EVQ11Y05B SPECIAL SWITCH S
D101 PFVD1N4005 DIODE(SI) S
SW28 EVQ11Y05B SPECIAL SWITCH S
D102 PFVD1N4005 DIODE(SI) S
SW30 EVQ11Y05B SPECIAL SWITCH S
D103 PFVD1N4005 DIODE(SI) S
SW31 EVQ11Y05B SPECIAL SWITCH S
D104 PFVD1N4005 DIODE(SI) S
SW32 EVQ11Y05B SPECIAL SWITCH S
D105 PQVDPR1007 DIODE(SI) S
SW33 EVQ11Y05B SPECIAL SWITCH S
D109 MA165 DIODE(SI) S
SW34 EVQ11Y05B SPECIAL SWITCH
D110 PFVD1N4005 DIODE(SI) S
SW35 EVQ11Y05B SPECIAL SWITCH
D201 PFVDSF5LC20U DIODE(SI) S
SW38 K0L1BA000095 SWITCH,SENSOR
D202 PFVDD1NL20U DIODE(SI) S
SW39 K0L1AA000002 SWITCH,SENSOR
D204 MA165 DIODE(SI) S
D205 HZS5.1NB3 DIODE(SI)
(RESISTORS)
D206 MA165 DIODE(SI) S
R1 ERJ3GEY0R00 0
R2 ERJ3GEY0R00 0
(CONNECTORS)
R3 ERJ3GEY0R00 0
CN202 PFJPB9BPHKL CONNECTOR, 9 PIN S
R4 ERJ3GEY0R00 0
CN31 PQJP2D98Z CONNECTOR, 2 PIN
R5 ERJ3GEY0R00 0
R14 ERJ3GEY0R00 0
(COIL)
R15 ERJ3GEYJ183 18K
L101 PFLES11V0523 COIL S
R17 ERJ3GEYJ222 2.2K
R18 ERJ3GEYJ271 270
(COMPONENTS PARTS)
R19 ERJ3GEYJ4R7 4.7
L103 EXCELDR35 COMPONENTS PARTS
R20 ERJ3GEYJ101 100
R21 ERJ3GEYJ101 100
(FUSE)
R22 ERJ3GEYJ472 4.7K
F101 PFBA250V3.15 FUSE S
R23 ERJ3GEYJ472 4.7K
R24 ERJ3GEYJ102 1K
(PHOTO ELECTRIC TRANSDUCER)
R25 ERJ3GEYJ821 820
PC101 PFVIPC123 PHOTO ELECTRIC TRANSDUCER S
R50 ERJ3GEYJ330 33
(CAPACITORS) S (TRANSFORMER)
C1 ECJ1VF1E104Z 0.1 T101 PFLTSRW28LEC TRANSFORMER S
C3 ECEA0JKA221 220
C4 ECJ1VB1H331K 330P (VARIABLE RESISTOR)
C6 ECJ1VB1H103K 0.01 VR201 ECNCYAA03B53 VARIABLE RESISTOR S
C13 ECJ1VB1H331K 330P
C14 ECJ1VC1H121J 120P (VARISTOR)
C15 ECJ1VF1E104Z 0.1 ZNR101 ERZV10D751 VARISTOR
C16 ECJ1VF1E104Z 0.1
C17 ECJ1VF1C224Z 0.22 (RESISTORS)
C19 ECJ1VB1H103K 0.01 JP204 ERJ3GEY0R00 0
C20 ECJ1VB1H103K 0.01 R101 ERDS1TJ105 1M
R102 ERJ3GEYJ103 10K
C10 ECJ1VF1E104Z 0.1 R105 ERX2SJR22E 0.22
C13 ECJ1VB1H331K 330P R106 ERG2SJ470 47
C14 ECJ1VC1H121J 120P R107 ERG2DJ104E 100K
172
KX-FT932FX-B
(CAPACITORS)
C101 ECQU2A104ML 0.1
C102 ECQU2A104ML 0.1
C103 PFKDD2GA102M 0.001 S
C105 PFKDD2GA332M 0.033 S
C106 EEUEB2W560U 56
C107 PFKDD3DD470J 47P S
C108 PFKDD3AD102K 0.001 S
C109 PFCEA35A47M 47 S
C110 PFKDD2GA102M 0.001 S
C121 ECUV1H472KBV 0.0047 S
C122 ECUV1E104KBV 0.1 S
C123 ECUV1H104KCV 0.1 S
C124 ECUV1H103KBV 0.01 S
C125 ECUV1H471JCV 470P S
C201 PFCEA35L220 22P S
C202 PFKDD3AD102K 0.001 S
C203 PFCEA16A470 47P S
C205 ECUV1E104KBV 0.1 S
Note:
Tools and Extension Cords are useful for servicing.
(They make servicing easy.)
Y.M
KXFT932FX
173