Fug 16 2001 16:57 ~—P.01/04
UDC 621.882.31:621.882.55 May 1967
Prevailing torque type hexagon nuts
with nonmetallic insert
Sechskantmuttern mit Klemmteil;
: Supersedes September 1977 edition
‘mit nichtmetalischem Eintatz, hohe Form withdrawn in 1983,
rear ner gece mane practice in sandrds published by the Interational Organisation for Standardization (150),
‘4 comms has been used throughout as the decime! marker.
Dimensions in men
1 Field of application
‘This standard specifies requirements for M 5 to M 24 prevailing torque type hexagon
‘nuts with nenmetallic insert, asigned to product grade A for sizes up to M 16 and
product grade 8 for sizes over M 16.
{f, in special cases, nus are to comply with specifications other than those given in this
‘standard, €.9, regarding materials other than those specified in DIN 267 Part 1
performance at temperatures above + 120°C, or corrosion resistance, this shall ba agreed
at the time of ordering (ef, DIN 267 Part 18)
2 Dimensions
Prevailing torque
clement (design oo
at the manufacturer's 46° 10%
discretion)
sn = minimum wrenching height.
Continued on pages 2 to 4
217Aug P.02/04
Page 2 DIN 962
ms | me | 7] Me |MW|Mia[ mis |wie| mis] ua [Ma] wae
~ | - |e [mio [ui2 [sa | wre | wie | mao | wae | wae
‘Thread size - xt xT [xt] xt8] x15] «2 ] x2] x2] x2
~ ||. >. )™@fwel. |. [wie | wz [wa]
tas] 125 xis | x38 | is
Po Ce cc
~ s |e {7 |[* |w [we [w [we |w [o |m |m
4
ou | 875 | a7s| a75[ avs[ woe [ve [ier [ws [ies |e | aa? |e
den eo | eo | v6 [ne [156 | 174 | 205 | 225 | 249 | 277 | 205 | a2
@ oo 879 11,05 | 12,12 | 1438 21.1 | 2449 | 2675 | 29,56 | 3295 | 35,03 | 39,55
1 wml |e | os [es [us uw [te fw [a lm [as |e
~ 6 | 77 | a2 | are| aise) vase} ssa | 7a | vere | 207 | m7 | mar
m?) min. 44 49 614 | 644] 804 | 1037] 121 | 141 | 151 | 169 | 181 | 202
man ase | aea| sar] 515 | 4s | es | ame | 1120 | 1200 | rase | vase | tore
, mum? | [u [we lv [w le lw le lo [a le
ee ze | oz [tars | 1273 | 1079 | veer | aver | ase | zee | zoe | at] as
1) P= pitch of coarse thread as specified in DIN 13 Part 12.
2) Also minimum thread length.
3 Technical delivery conditions
Material ~ Steel
General requirements
As specified in DIN 267 Parts 1 and 15.
Tolerance eat)
These
As specified in DIN 13 Parts 12 end 18.
Shani Property class 5,62), 8 or 10;
Mechanical material only for sizes up to M 1
Mechanic (omateral : 12 (ony for sizes upto M 16).
{out beay ‘As specified in 150 896 Part 2 and DIN 267 Part 15.
Matera inert)
Performance (prevailing torques)
‘As specified in DIN 267 Part 18.
Limit deviations ang Product grade
geometrical tolerances
As specified in
For sizes up to M 16: A (previously, design ml.
For sizes over M 16: B (previously, design mg).
1S0 4759 Pert 1,
Surface finish
‘Acceptance inepaction
[As processed.
DIN 267 Pert 2 shall apply with ragard to turface roughness.
DIN 267 Part 20 shall apply with regard to permissible surface
discontinuities.
DIN 267 Part 8 shall apply with regard to electroplating.
DIN 267 Part § shell apply with regerd to ecceptance inspection.
1) See DIN 267 Part 15 in thit
2) Only for fine thread nurs
spect.
218Fug 16 2001 16:58 = P..05/04
OIN 962 Page 3
4 Mass
‘The values of mats ara given for guidance only
Thread size us mo [ M7 | we m10/ M12] Mia Mio] Mie M20] M22] M26
Mass (7,88 kg/ém9) for [| Ts | | |
tooounitwinnsis | “| | 92 | @ | m7 | se] ar | ora] sro | oe | oe | var
Approximately the some values may be assumed for fine thread nuts
5 Designation
Designation of an M 12 p:
ling torque type hexagon nut with a nonmetallic insart, assigned to property class 8:
Hexagon nut DIN 982—~M 12-8
If nuts of sizes over M16
‘the designation by adding
10 comply with product grade A (as spec
“Avege
{in 180 4759 Part 1), this shall be indicated in
Hexagon nut DIN 982 - M 20-8 ~ A
‘The DIN 4000 — 2-7 tabular layout of article characteristics shall apply for nuts covered in this andird,
6 Marking
‘Nuts shall be marked in accordance with the epeeifications of OIN 267 Part 18.
Note for users
Tolerance class 6H shall apply for the thread of nuts with and without coating.
Crean Protective costings applied, eg an electroplated coating complying with DIN 267 Part 9, depending on the
Soaring thickness required, it may be necesary to select a larger fundamental deviation than thet ssned to she
Position (see DIN 267 Part 8). This, however, might impair the resistance of the boltnut esembly to tipping
219