Beruflich Dokumente
Kultur Dokumente
# 13 and # 14
For dry contact activation ( Push
Button)
# 17 and # 18
For serial or voltage pulse
activation, (not to exceed 24V)
#4 and # 8 loop
CX-91M-06
Installation Instructions
5502 Timberlea Blvd.
Mississauga, Ontario L4W 2T7
905-366-3377 Toll Free: 877-226-3369
www.camdencontrols.com
CX-91M-06TDS Single adj. timer, door position switch & bond sensor
SHOCK HAZARD. Care must be taken to keep the power supply and wiring isolated from ground
(earth). Use of an ohmmeter to test for shorts is recommended prior to service.
A. 12V DC Input:
Set jumpers for 12V DC operation. (See diagram below) Connect the ground (-) lead from a 12V
DC power source to terminal 2.Connect the positive (+) lead from a 12V DC power source to
terminal 1.
B. 24V DC Input:
Unit is delivered from Factory with single jumper ON for 24V operation.Connect the ground (-)
lead from a 24V DC power source to terminal 2.Connect the positive (+) lead from a 24V DC
power source to terminal.
C. Contacts:
Reed switch dry contacts are rated 0.5 Amp@30V DC/AC. For safe operation, do not exceed
this rating.If you normally require a normally open contact, connect to the black and green wire of
the PCB.If you normally require a normally closed contact, connect to the black and red wire of
the PCB.
Printed Circuit Board Schematic
(shown with all options)
Jumper 12V DC 24V DC Magnet Power Selector IC 1 Timer Power Supply Reed Switch (Sensor)
White Blue Green Black Red NC NO VR C110 V AC Switch or Solid State Switching Device 12
or 24 VDC CORRECT 110 V AC Switch or Solid State Switching Device 12 or 24 VDC
INCORRECT
Important
Power switch should always be wired as shown below in order to minimize the effect of residual
magnetism.
Contact Camden for other wiring considerations.
Turnstile Counter
Technical Manual
702084-0001
Series C342
Self Powered
LCD Display
HV Input
Introduction
Your Veeder-Root brand Series C342 panel instrument is powered by an internal lithium
battery, features an 8 digit LCD display and is housed in a ultra compact 1/32 DIN
package. An IEC IP65 rated front panel is suitable for washdown environments.
All models feature signal and remote-reset inputs capable of accepting the high voltage AC
or DC impulses They can be applied in much the same manner as electromechanical
devices of similar voltage rating, but have the inherent life and reliability benefits of modern
electronic design.
This product has been configured at the factory to perform one of the following functions:
Count Totalizer, Time Totalizer (Hours:Minutes:Seconds), or Time Totalizer (Hours, 1/100
resolution).
Features
• Available models include count and time
totalization
• Unique input circuit accepts 12 to 250 V,
AC/DC, for signal and reset functions
• Crisp 8 digit LCD display provides easy to
read process values
• Compact 1/32 DIN bezel and 60mm
behind the panel depth save panel space
• Internal lithium battery provides long life
and eliminates the need for external power
• IEC IP65 rated front panel for use in
washdown environments
Veeder-Root brand
SETUP
OPERATION
Front Panel Reset
Used to reset the Process Value
Display, unless disabled through the
keylock input
ABB Modular
Range of Pilot
Devices
In addition to traditional operators like Pushbuttons, Selector switches, Emergency
stops and Pilot lights, ABB also offers a wide range of special functions such as
Machine stops, Toggle switches, Buzzers, Definite purpose pushbuttons,
Potentiometers and Reset buttons.
The pilot devices have a modern, robust and functional design and can be used both
indoor and outdoor. On front side the products meet protection degree IP66 and on
terminal side they meet IP20. They are also approved in accordance with UL Type 1,
3R, 4, 4X, 12 and 13.
Operators are available with bezels in three different alternatives i.e. black plastic,
chrome plastic and metal. Rotation is prevented by ridges and springs on the
operators.
The Contact blocks are provided with a wiping, cleaning function to secure the
contact function. The contact carriers are color coded to indicate normally open and
normally closed contacts. For all illuminated products the same lamp blocks can be
used for both filament bulbs and LED’s.
The operators and pilot lights are fast and easy to install by use of snap-on solutions.
Installation of contact blocks and actuators can be done separately and pre-wiring is
possible.