Beruflich Dokumente
Kultur Dokumente
Activate
Issue 8-0
Activating and Testing BSS5050, BSS10118,
BSS11116 and BSS8085: Dual Band Network Opera-
The information in this document is subject to change without notice and describes only the
product defined in the introduction of this documentation. This documentation is intended for the
use of Nokia Siemens Networks customers only for the purposes of the agreement under which
the document is submitted, and no part of it may be used, reproduced, modified or transmitted
in any form or means without the prior written permission of Nokia Siemens Networks. The
documentation has been prepared to be used by professional and properly trained personnel,
and the customer assumes full responsibility when using it. Nokia Siemens Networks welcomes
customer comments as part of the process of continuous development and improvement of the
documentation.
The information or statements given in this documentation concerning the suitability, capacity,
or performance of the mentioned hardware or software products are given "as is" and all liability
arising in connection with such hardware or software products shall be defined conclusively and
finally in a separate agreement between Nokia Siemens Networks and the customer. However,
Nokia Siemens Networks has made all reasonable efforts to ensure that the instructions
contained in the document are adequate and free of material errors and omissions. Nokia
Siemens Networks will, if deemed necessary by Nokia Siemens Networks, explain issues which
may not be covered by the document.
Nokia Siemens Networks will correct errors in this documentation as soon as possible. IN NO
EVENT WILL Nokia Siemens Networks BE LIABLE FOR ERRORS IN THIS DOCUMENTA-
TION OR FOR ANY DAMAGES, INCLUDING BUT NOT LIMITED TO SPECIAL, DIRECT, INDI-
RECT, INCIDENTAL OR CONSEQUENTIAL OR ANY LOSSES, SUCH AS BUT NOT LIMITED
TO LOSS OF PROFIT, REVENUE, BUSINESS INTERRUPTION, BUSINESS OPPORTUNITY
OR DATA,THAT MAY ARISE FROM THE USE OF THIS DOCUMENT OR THE INFORMATION
IN IT.
This documentation and the product it describes are considered protected by copyrights and
other intellectual property rights according to the applicable laws.
The wave logo is a trademark of Nokia Siemens Networks Oy. Nokia is a registered trademark
of Nokia Corporation. Siemens is a registered trademark of Siemens AG.
Other product names mentioned in this document may be trademarks of their respective
owners, and they are mentioned for identification purposes only.
Copyright © Nokia Siemens Networks 2010. All rights reserved
2 Id:0900d8058059c23c DN9812734
Issue 8-0
Activating and Testing BSS5050, BSS10118,
BSS11116 and BSS8085: Dual Band Network Opera-
Table of Contents
This document has 22 pages.
Summary of changes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
1 Activating and testing Dual Band Network Operation (GSM 900/1800, GSM
800/1900, GSM 800/1800, and PGSM 900/EGSM 900) . . . . . . . . . . . . . 6
1.1 Activating Dual Band Network Operation (GSM 900/1800) . . . . . . . . . . . 6
1.2 Testing Dual Band Network Operation (GSM 900/1800). . . . . . . . . . . . . 7
1.3 Activating Dual Band Network Operation (GSM 800/1900) . . . . . . . . . . . 9
1.4 Testing Dual Band Network Operation (GSM 800/1900). . . . . . . . . . . . 10
1.5 Activating Dual Band Network Operation (GSM 800/1800) . . . . . . . . . . 12
1.6 Testing Dual Band Network Operation (GSM 800/1800). . . . . . . . . . . . 13
1.7 Activating Dual Band Network Operation (PGSM 900/EGSM 900) . . . . 14
1.8 Testing Dual Band Network Operation (PGSM 900/EGSM 900). . . . . . 15
DN9812734 Id:0900d8058059c23c 3
Issue 8-0
Activating and Testing BSS5050, BSS10118,
BSS11116 and BSS8085: Dual Band Network Opera-
4 Id:0900d8058059c23c DN9812734
Issue 8-0
Activating and Testing BSS5050, BSS10118, Summary of changes
BSS11116 and BSS8085: Dual Band Network Opera-
Summary of changes
Changes between document issues are cumulative. Therefore, the latest document
issue contains all changes made to previous issues.
DN9812734 Id:0900d8058059c233 5
Issue 8-0
Activating and testing Dual Band Network Operation Activating and Testing BSS5050, BSS10118,
(GSM 900/1800, GSM 800/1900, GSM 800/1800, and BSS11116 and BSS8085: Dual Band Network Opera-
6 Id:0900d8058059c236 DN9812734
Issue 8-0
Activating and Testing BSS5050, BSS10118, Activating and testing Dual Band Network Operation
BSS11116 and BSS8085: Dual Band Network Opera- (GSM 900/1800, GSM 800/1900, GSM 800/1800, and
Steps
1 Tune the BTS1 and BTS2 to a proper frequency band (BTS1 <-> GSM 900, BTS2 <-
> GSM 1800).
8 Take into account the adjacencies on the other band of BTS1 (EQF).
ZEQF:BTS=1:DBC=Y;
9 Take into account the adjacencies on the other band of BTS2 (EQF).
ZEQF:BTS=2:DBC=Y;
Further information
Next, test Dual Band Network Operation (GSM 900/1800).
DN9812734 Id:0900d8058059c236 7
Issue 8-0
Activating and testing Dual Band Network Operation Activating and Testing BSS5050, BSS10118,
(GSM 900/1800, GSM 800/1900, GSM 800/1800, and BSS11116 and BSS8085: Dual Band Network Opera-
3 Set the value of the PBGT HO margin from cell BTS1 to adjacent cell BTS2 to —24
dB to trigger the PBGT HO (EAM).
ZEAM:BTS=1::ABTS=2::PMRG=-24;
g The existing value of PBGT HO margin should be restored after the test.
4 Set the value of the PBGT HO margin from cell BTS2 to adjacent cell BTS1 to -24
dB to trigger the PBGT HO (EAM).
ZEAM:BTS=2::ABTS=1::PMRG=-24;
g The existing value of PBGT HO margin should be restored after the test.
Expected outcome
• Dual Band Network Operation is activated in the BSC.
• A call is set up to the GSM 900 cell, and successive handovers between GSM 900
and GSM 1800 cells are made.
• The test results are verified from the BSC Level Clear Code (PM) Measurements
that indicate the number of successful handovers.
Expected outcome
The administrative state is UNLOCKED and the operational state is ENABLED.
8 Id:0900d8058059c236 DN9812734
Issue 8-0
Activating and Testing BSS5050, BSS10118, Activating and testing Dual Band Network Operation
BSS11116 and BSS8085: Dual Band Network Opera- (GSM 900/1800, GSM 800/1900, GSM 800/1800, and
12 Verify the success level of the power budget handovers by using the BSC Level
Clear Code (PM) Measurement.
At the end of the measurement period, check the measurement file in Nokia NetAct or
using the MEFICO tool. For more information, see:
• Reporter and Performance Management Principlesin NetAct documentation
• Converting BSC Measurement and Observation Files with MEFICO
Expected outcome
The counter 051013 INTERNAL_INTER_HO_SUCCESS is updated in both cells.
Expected outcome
The administrative state is now LOCKED and the operational state is DISABLED.
Steps
1 Tune BTS1 and BTS2 to a proper frequency band (BTS1 <-> GSM 800, BTS2 <->
GSM 1900).
DN9812734 Id:0900d8058059c236 9
Issue 8-0
Activating and testing Dual Band Network Operation Activating and Testing BSS5050, BSS10118,
(GSM 900/1800, GSM 800/1900, GSM 800/1800, and BSS11116 and BSS8085: Dual Band Network Opera-
Further information
Next, test Dual Band Network Operation (GSM 800/1900).
3 Set the value of the PBGT HO margin from cell BTS1 to adjacent cell BTS2 to —24
dB to trigger the PBGT HO (EAM).
ZEAM:BTS=1::ABTS=2::PMRG=-24;
g The existing value of PBGT HO margin should be restored after the test.
4 Set the PBGT HO margin from cell BTS2 to adjacent cell BTS1 to value -24 dB to
trigger the PBGT HO (EAM).
ZEAM:BTS=2::ABTS=1::PMRG=-24;
g The existing value of PBGT HO margin should be restored after the test.
Expected outcome
• Dual Band Network Operation is activated in the BSC.
10 Id:0900d8058059c236 DN9812734
Issue 8-0
Activating and Testing BSS5050, BSS10118, Activating and testing Dual Band Network Operation
BSS11116 and BSS8085: Dual Band Network Opera- (GSM 900/1800, GSM 800/1900, GSM 800/1800, and
• A call is set up to the GSM 800 cell, and successive handovers between GSM 800
and GSM 1900 cells are made.
• The test results are verified from the BSC clear code measurements that indicate
the number of successful handovers.
Expected outcome
The administrative state is UNLOCKED and the operational state is ENABLED.
12 Verify the success level of handovers by using BSC Level Clear Code (PM) Mea-
surement.
At the end of the measurement period, check the measurement file in Nokia NetAct or
using the MEFICO tool. For more information, see:
• Reporter and Performance Management Principles in NetAct documentation
• Converting BSC Measurement and Observation Files with MEFICO
Expected outcome
The counter 051013 INTERNAL_INTER_HO_SUCCESS is updated in both cells.
DN9812734 Id:0900d8058059c236 11
Issue 8-0
Activating and testing Dual Band Network Operation Activating and Testing BSS5050, BSS10118,
(GSM 900/1800, GSM 800/1900, GSM 800/1800, and BSS11116 and BSS8085: Dual Band Network Opera-
Steps
1 Tune BTS1 and BTS2 to a proper frequency band (BTS1 <-> GSM 800, BTS2 <->
GSM 1800).
12 Id:0900d8058059c236 DN9812734
Issue 8-0
Activating and Testing BSS5050, BSS10118, Activating and testing Dual Band Network Operation
BSS11116 and BSS8085: Dual Band Network Opera- (GSM 900/1800, GSM 800/1900, GSM 800/1800, and
Further information
Next, test Dual Band Network Operation (GSM 800/1800).
3 Set the value of the PBGT HO margin from cell BTS1 to adjacent cell BTS2 to -24
dB to trigger the PBGT HO (EAM).
ZEAM:BTS=1::ABTS=2::PMRG=-24;
g The existing value of PBGT HO margin should be restored after the test.
4 Set the value of the PBGT HO margin from cell BTS2 to adjacent cell BTS1 to -24
dB to trigger the PBGT HO (EAM).
ZEAM:BTS=2::ABTS=1::PMRG=-24;
g The existing value of PBGT HO margin should be restored after the test.
Expected outcome
• Dual Band Network Operation is activated in the BSC.
• A call is set up to the GSM 800 cell, and successive handovers between GSM 800
and GSM 1800 cells are made.
• The test results are verified from the BSC clear code measurements that indicate
the number of successful handovers.
DN9812734 Id:0900d8058059c236 13
Issue 8-0
Activating and testing Dual Band Network Operation Activating and Testing BSS5050, BSS10118,
(GSM 900/1800, GSM 800/1900, GSM 800/1800, and BSS11116 and BSS8085: Dual Band Network Opera-
12 Verify the success level of handovers by using BSC Level Clear Code (PM) Mea-
surement.
At the end of the measurement period, check the measurement file in Nokia NetAct or
using the MEFICO tool. For more information, see:
• Reporter and Performance Management Principles in NetAct documentation
• Converting BSC Measurement and Observation Files with MEFICO
Expected outcome
The counter 051013 INTERNAL_INTER_HO_SUCCESS is updated in both cells.
14 Id:0900d8058059c236 DN9812734
Issue 8-0
Activating and Testing BSS5050, BSS10118, Activating and testing Dual Band Network Operation
BSS11116 and BSS8085: Dual Band Network Opera- (GSM 900/1800, GSM 800/1900, GSM 800/1800, and
Steps
1 Tune BTS1 and BTS2 to a proper frequency band (BTS1 <-> PGSM 900, BTS2 <->
EGSM 900).
Further information
Next, test Dual Band Network Operation (PGSM 900/EGSM 900).
3 Set the value of the PBGT HO margin from cell BTS1 to adjacent cell BTS2 to -24
dB to trigger the PBGT HO (EAM).
ZEAM:BTS=1::ABTS=2::PMRG=-24;
g The existing value of PBGT HO margin should be restored after the test.
DN9812734 Id:0900d8058059c236 15
Issue 8-0
Activating and testing Dual Band Network Operation Activating and Testing BSS5050, BSS10118,
(GSM 900/1800, GSM 800/1900, GSM 800/1800, and BSS11116 and BSS8085: Dual Band Network Opera-
4 Set the value of the PBGT HO margin from cell BTS2 to adjacent cell BTS1 to -24
dB to trigger the PBGT HO (EAM).
ZEAM:BTS=2::ABTS=1::PMRG=-24;
g The existing value of PBGT HO margin should be restored after the test.
Expected outcome
• Dual Band Network Operation is activated in the BSC.
• A call is set up to the PGSM 900 cell, and successive handovers between PGSM
900 and EGSM 900 cells are made.
• The test results are verified from the BSC clear code measurements that indicate
the number of successful handovers.
12 Verify the success level of handovers by using BSC Level Clear Code (PM) Mea-
surement.
At the end of the measurement period, check the measurement file in Nokia NetAct or
using the MEFICO tool. For more information, see:
• Reporter and Performance Management Principles in NetAct documentation
• Converting BSC Measurement and Observation Files with MEFICO
Expected outcome
The counter 051013 INTERNAL_INTER_HO_SUCCESS is updated in both cells.
16 Id:0900d8058059c236 DN9812734
Issue 8-0
Activating and Testing BSS5050, BSS10118, Activating and testing Dual Band Network Operation
BSS11116 and BSS8085: Dual Band Network Opera- (GSM 900/1800, GSM 800/1900, GSM 800/1800, and
DN9812734 Id:0900d8058059c236 17
Issue 8-0
Deactivating and testing Dual Band Network Operation Activating and Testing BSS5050, BSS10118,
(GSM 900/1800, GSM 800/1900 and GSM 800/1800) BSS11116 and BSS8085: Dual Band Network Opera-
Steps
3 Modify the counters of BSC Level Clear Code (PM) Measurement (TPM).
ZTPM:MEASUR,CC_PM:<measurement day>,<measurement
interval>,<output interval>;
18 Id:0900d8058059c239 DN9812734
Issue 8-0
Activating and Testing BSS5050, BSS10118, Deactivating and testing Dual Band Network Operation
BSS11116 and BSS8085: Dual Band Network Opera- (GSM 900/1800, GSM 800/1900 and GSM 800/1800)
11 Verify the success level of handovers by using BSC Level Clear Code (PM) Mea-
surement.
At the end of the measurement period, check the measurement file in Nokia NetAct or
using the MEFICO tool. For more information, see:
• Reporter and Performance Management Principles in NetAct documentation
• Converting BSC Measurement and Observation Files with MEFICO
Expected outcome
The counter 051013 INTERNAL_INTER_HO_SUCCESS is not updated (no handovers
are made).
DN9812734 Id:0900d8058059c239 19
Issue 8-0
Deactivating and testing Dual Band Network Operation Activating and Testing BSS5050, BSS10118,
(GSM 900/1800, GSM 800/1900 and GSM 800/1800) BSS11116 and BSS8085: Dual Band Network Opera-
where
BTS=2 is the GSM 1900 cell identification
3 Modify the counters of BSC Level Clear Code (PM) Measurement (TPM).
ZTPM:MEASUR,CC_PM:<measurement day>,<measurent interval>,<output
interval>;
11 Verify the success level of handovers by using BSC Level Clear Code (PM) Mea-
surement.
At the end of the measurement period, check the measurement file in Nokia NetAct or
using the MEFICO tool. For more information, see:
• Reporter and Performance Management Principles in NetAct documentation
20 Id:0900d8058059c239 DN9812734
Issue 8-0
Activating and Testing BSS5050, BSS10118, Deactivating and testing Dual Band Network Operation
BSS11116 and BSS8085: Dual Band Network Opera- (GSM 900/1800, GSM 800/1900 and GSM 800/1800)
Expected outcome
The counter 051013 INTERNAL_INTER_HO_SUCCESS is not updated (no handovers
are made).
3 Modify the counters of the BSC Level Clear Code (PM) Measurement (TPM).
ZTPM:MEASUR,CC_PM:<measurement day>,<measurent interval>,<output
interval>;
DN9812734 Id:0900d8058059c239 21
Issue 8-0
Deactivating and testing Dual Band Network Operation Activating and Testing BSS5050, BSS10118,
(GSM 900/1800, GSM 800/1900 and GSM 800/1800) BSS11116 and BSS8085: Dual Band Network Opera-
11 Verify the success level of handovers by using BSC Level Clear Code (PM) Mea-
surement.
At the end of the measurement period, check the measurement file in Nokia NetAct or
using the MEFICO tool. For more information, see:
• Reporter and Performance Management Principles in NetAct documentation
• Converting BSC Measurement and Observation Files with MEFICO
Expected outcome
The counter 051013 INTERNAL_INTER_HO_SUCCESS is not updated (no handovers
are made).
22 Id:0900d8058059c239 DN9812734
Issue 8-0