Sie sind auf Seite 1von 9

1

Refer to the exhibit. Based on the output as shown, which two statements correctly define how the router will
treat Telnet traffic that comes into interface FastEthernet 0/1? (Choose two).
Telnet to 172.16.10.0/24 is denied.
Telnet to 172.16.20.0/24 is denied.
Telnet to 172.16.0.0/24 is permitted.
Telnet to 172.16.10.0/24 is permitted.
Telnet to 172.16.20.0/24 is permitted.

2 Which data link layer encapsulation protocol is used by default for serial connections between two Cisco
routers?
ATM
Frame Relay
HDLC
PPP
SDLC

3
Refer to the exhibit. Which two conclusions are indicated by the output? (Choose two.)
The router is not experiencing congestion.
DLCI 102 has been active for 30:31 minutes.
The upstream router is experiencing congestion.
The downstream router is experiencing congestion.
The virtual circuit cannot be completed until the PVC status changes.

Refer to the exhibit. R1 is performing NAT overload for the 10.1.1.0/24 inside network. Host A has sent a
packet to the web server. What is the destination IP address of the return packet from the web server?
10.1.1.2:1234
172.30.20.1:1234
172.30.20.1:3333
192.168.1.2:80

5 Which configuration on the vty lines provides the best security measure for network administrators to remotely
access the core routers at headquarters?
6 Where does a service provider assume responsibility from a customer for a WAN connection?
local loop
DTE cable on router
demarcation point
demilitarized zone

7 Which statement is true about PAP in the authentication of a PPP session?


PAP uses a two-way handshake.
The password is unique and random.
PAP conducts periodic password challenges.
PAP uses MD5 hashing to keep the password secure.

8
Refer to the exibit. A network technician has configured the Frame Relay network but is unable to ping between
R1 and R2. What set of commands must the technician issue to fix this problem?
R2(config-if)# no frame-relay map ip 10.1.1.2 102 broadcast
R2(config-if)# frame-relay map ip 10.1.1.1 201 broadcast
R1(config-if)# no frame-relay map ip 10.1.1.2 201 broadcast
R1(config-if)# frame-relay map ip 10.1.1.1 102 broadcast
R2(config-if)# no frame-relay map ip 10.1.1.2 102 broadcast
R2(config-if)# frame-relay map ip 10.1.1.2 201 broadcast
R1(config-if)# no frame-relay map ip 10.1.1.1 201 broadcast
R1(config-if)# frame-relay map ip 10.1.1.2 102 broadcast

9
Refer to the exhibit. Every time the administrator reboots this router, the boot process ends in setup mode. What
is a possible problem?
There is insufficient RAM for the IOS to load on this router.
A password recovery process should be done on this router.
The bootstrap version and the version of the IOS are different.
The IOS image is damaged and must be reloaded using tftpdnld.
The configuration register is set to ignore the startup configuration.

10

Refer to the exhibit. What can be concluded from the exhibited output of the debug ip nat command?
The 10.1.1.225 host is exchanging packets with the 192.168.0.10 host.
The native 10.1.200.254 address is being translated to 192.168.0.10.
The 192.168.0.0/24 network is the inside network.
Port address translation is in effect.

11 When would the multipoint keyword be used in Frame Relay PVCs configuration?
when global DLCIs are in use
when using physical interfaces
when multicasts must be supported
when participating routers are in the same subnet

12

Refer to the exhibit. A network administrator is trying to connect R1 remotely to make configuration changes.
Based on the exhibited command output, what will be the result when attempting to connect to R1?
failure to connect due to Telnet not being enabled
failure to connect due to incomplete configuration for Telnet
a successful connection and ability to make configuration changes
a successful connection but inability to make configuration changes because of the absence of an enable
secret password

13 Which statement is true about NCP?


Link termination is the responsibility of NCP.
Each network protocol has a corresponding NCP.
NCP establishes the initial link between PPP devices.
NCP tests the link to ensure that the link quality is sufficient.

14

Refer to the exhibit. What is the meaning of the term dynamic in the output of the command?
The bandwidth capability of the interface increases and decreases automatically based on BECNs.
The Serial0/0/1 interface acquired 172.16.3.1 from a DHCP server.
The mapping between DLCI 100 and 172.16.3.1 was learned through Inverse ARP.
DLCI 100 will automatically adapt to changes in the Frame Relay cloud.
15

Refer to the exhibit. Headquarters is connected through the Internet to branch office A and branch office B.
Which WAN technology would be best suited to provide secure connectivity between headquarters and both
branch offices?
ATM
VPN
ISDN
Frame Relay
broadband DSL

16

Refer to the exhibit. A host connected to Fa0/0 is unable to acquire an IP address from the DHCP server. The
output of the debug ip dhcp server command shows "DHCPD: there is no address pool for 10.1.1.1". What is
the problem?
The 10.1.1.1 address is already configured on Fa0/0.
The default router for the 10Network pool is incorrect.
The ip helper-address must be added to Fa0/0 interface.
The pool of addresses for the 10Network pool is incorrect.

17
Refer to the exhibit. Results of the show vlan and show vtp status commands for switches S1 and S2 are
displayed in the exhibit. VLAN 11 was created on S1. Why is VLAN 11 missing from S2?
There is a Layer 2 loop.
The VTP domain names do not match.
Only one switch can be in server mode.
S2 has a higher spanning-tree priority for VLAN 11 than S1 does.

18 What will be the result of adding the command ip dhcp excluded-address 192.168.24.1 192.168.24.5 to the
configuration of a local router that has been configured as a DHCP server?
Traffic that is destined for 192.168.24.1 and 192.168.24.5 will be dropped by the router.
Traffic will not be routed from clients with addresses between 192.168.24.1 and 192.168.24.5.
The DHCP server will not issue the addresses ranging from 192.168.24.1 to 192.168.24.5.
The router will ignore all traffic that comes from the DHCP servers with addresses 192.168.24.1 and
192.168.24.5.

19 An issue of response time has recently arisen on an application server. The new release of a software package
has also been installed on the server. The configuration of the network has changed recently. To identify the
problem, individuals from both teams responsible for the recent changes begin to investigate the source of the
problem. Which statement applies to this situation?
Scheduling will be easy if the network and software teams work independently.
It will be difficult to isolate the problem if two teams are implementing changes independently.
Results from changes will be easier to reconcile and document if each team works in isolation.
Only results from the software package should be tested as the network is designed to accommodate the
proposed software platform.

20
Refer to the exhibit. RIPv2 has been configured on all routers in the network. Routers R1 and R3 have not
received any RIP routing updates. What will fix the issue?
Enable RIP authentication on R2.
Issue the ip directed-broadcast command on R2.
Change the subnet masks to 10.11.12.0/8 and 172.16.40.0/16 on R2.
Enable CDP on R2 so that the other routers will receive routing updates.

Das könnte Ihnen auch gefallen