Beruflich Dokumente
Kultur Dokumente
EQUIPMENT ID NUMBER(S) EQUIPMENT DESCRIPTION EQPT CODE SYSTEM ID. PLANT NO.
LAYOUT DRAWING NUMBER REV. NO. PURCHASE ORDER NUMBER EC / PMCC / MCC NO.
SCHEDULED INSPECTION DATE & TIME ACTUAL INSPECTION DATE & TIME QUANTITY INSP. MH's SPENT TRAVEL TIME
SAUDI ARAMCO USE ONLY
SAUDI ARAMCO TIP NUMBER SAUDI ARAMCO ACTIVITY NUMBER WORK PERMIT REQUIRED?
ITEM
ACCEPTANCE CRITERIA REFERENCE PASS FAIL N/A RE-INSP DATE
No.
12-SAMSS-007,
A1 All bolts are of new stock.
Para. 4.1.1
All ASTM A325 or ASTM A325M high-strength bolts, shall be Type 1, plain, 12-SAMSS-007,
A3
for structures that are painted. Para. 6.2.5.4
Mill test reports for each heat of high strength bolts are available for review
and verified to meet the requirements of the ASTM A325 specification. 12-SAMSS-007,
A5
(AISC Specification for Structural Joints Using ASTM A325 or A490 Bolts, Para. 6.2.5.2 a
Para. 2.1)
ASTM A 325 bolts are properly identified and marked with the material
grade and manufacturer's logo in accordance with Attachment 3 of this 12-SAMSS-007,
A7
checklist. (AISC Specification for Structural Joints Using ASTM A325 or Para. 6.2.5.5
A490 Bolts, Figures C-2.1& C-2.2)
12-SAMSS-007,
B1 All nuts are of new stock.
Para. 4.1.1
Mill test reports for each heat of heavy hexagonal nuts are available for
review and verified to meet the requirements of the ASTM A563 12-SAMSS-007,
B2
specification. (AISC Specification for Structural Joints Using ASTM A325 or Para. 7.6
A490 Bolts, Para. 2.1 and 2.4.1)
Heavy Hex Nut shall be ASTM A563 Grade DH or ASTM A563M Grade
12-SAMSS-007,
B4 10S(AISC Specification for Structural Joints Using ASTM A325 or A490
Para. 6.2.5.2 a
Bolts, Table 2.1.) as shown in Attachment 2 of this checklist.
Page 1 of 6
SAUDI ARAMCO ID/PID - 25-MAY-05 - REV 0 (Standards Cutoff - August 2004)
SAIC NUMBER DATE APPROVED QR NUMBER
SAUDI ARAMCO INSPECTION CHECKLIST
Receiving Inspection - Bolts, Nuts & Washers for Structural
SAIC-M-2021 25-May-05 MECH-
Connections
PROJECT TITLE WBS / BI / JO NUMBER CONTRACTOR / SUBCONTRACTOR
ITEM
ACCEPTANCE CRITERIA REFERENCE PASS FAIL N/A RE-INSP DATE
No.
Heavy hexagonal nuts are properly identified and marked with the material
grade and manufacturer's logo in accordance with Attachment 3 of this 12-SAMSS-007,
B5
checklist. (AISC Specification for Structural Joints Using ASTM A325 or Para. 6.2.5.6
A490 Bolts, Figures C-2.1& C-2.2)
All bolts, washers and nuts shall be packaged and delivered in rigid , 12SAMSS007,
B6
weather proof containers, cardboard containers are not acceptable 6.3.1.2
Mechanically galvanized bolts and nuts shall not be intermixed with hot-dip 12-SAMSS-008,
B7
galvanized nuts and bolts. (PIP-STS05130, Para. 6.5.4) Sec. I
12-SAMSS-007,
C1 All washers are of new stock.
Para. 4.1.1
Mill test reports for each heat of flat circular washers and square or
rectangular beveled washers are available for review and verified to meet 12-SAMSS-007,
C2
the requirements of the ASTM F436 specification. (AISC Specification for Para. 7.6
Structural Joints Using ASTM A325 or A490 Bolts, Para. 2.5)
The type and finish of washers conform with Attachment 2 of this checklist.
12-SAMSS-007,
C3 (AISC Specification for Structural Joints Using ASTM A325 or A490 Bolts,
Para. 6.2.5.2 a
Para. 2.5 & Table 2.1)
Fastener components (bolts, nuts and washers) shall be protected from dirt
and moisture in closed containers in a protected shelter. (AISC 12-SAMSS-007,
C5
Specification for Structural Joints Using ASTM A325 or A490 Bolts, Para. Para. 6.2.5.2 a
2.2)
Mill test reports for each heat of ASTM A 307 bolts, are available for review 12-SAMSS-007,
D1
and verified to meet the requirements of the ASTM A307 specification. Para. 7.6
12-SAMSS-007,
D2 Nuts shall be ASTM A563 Grade A (Hex ¼" - 1½" diameter)
Para. 4.7
12-SAMSS-007,
D3 Washer shall be ASTM F436.
Para. 4.7
ASTM A307 bolt shall be limited in size to 5/8 inch (16 mm) diameter and 12-SAMSS-007,
D4
smaller. Para. 6.2.5.10
Page 2 of 6
SAUDI ARAMCO ID/PID - 25-MAY-05 - REV 0 (Standards Cutoff - August 2004)
SAIC NUMBER DATE APPROVED QR NUMBER
SAUDI ARAMCO INSPECTION CHECKLIST
Receiving Inspection - Bolts, Nuts & Washers for Structural
SAIC-M-2021 25-May-05 MECH-
Connections
PROJECT TITLE WBS / BI / JO NUMBER CONTRACTOR / SUBCONTRACTOR
Direct tension indicators met the dimensional requirements of per Table 4 12-SAMSS-008,
E2
of Attachment 4. {ASTM F 959, Para. 15} Sec. I
Each direct tension indicator shall be marked to identify the lot number,
12-SAMSS-008,
E3 manufacturer or private label distribution, as appropriate, and type (A325
Sec. I
and A490). {ASTM F 959, Para. 17.1}
Mechanically galvanized bolts and nuts shall not be intermixed with hot-dip 12-SAMSS-008,
F1
galvanized nuts and bolts. (PIP-STS05130, Para. 6.5.4) Sec. I
Materials shall be kept free of dirt, grease, and other foreign matter.(PIP- 12-SAMSS-008,
F3
STS05130, Para. 6.1.1) Sec. I
REMARKS:
REFERENCE DOCUMENTS:
Page 3 of 6
SAUDI ARAMCO ID/PID - 25-MAY-05 - REV 0 (Standards Cutoff - August 2004)
SAIC NUMBER DATE APPROVED QR NUMBER
SAUDI ARAMCO INSPECTION CHECKLIST
Receiving Inspection - Bolts, Nuts & Washers for Structural
SAIC-M-2021 25-May-05 MECH-
Connections
ATTACHMENT 1
Page 4 of 6
SAUDI ARAMCO ID/PID - 25-MAY-05 - REV 0 (Standards Cutoff - August 2004)
SAIC NUMBER DATE APPROVED QR NUMBER
SAUDI ARAMCO INSPECTION CHECKLIST
Receiving Inspection - Bolts, Nuts & Washers for Structural
SAIC-M-2021 25-May-05 MECH-
Connections
ATTACHMENT 2
Page 5 of 6
SAUDI ARAMCO ID/PID - 25-MAY-05 - REV 0 (Standards Cutoff - August 2004)
SAIC NUMBER DATE APPROVED QR NUMBER
SAUDI ARAMCO INSPECTION CHECKLIST
Receiving Inspection - Bolts, Nuts & Washers for Structural
SAIC-M-2021 25-May-05 MECH-
Connections
ATTACHMENT 3
Figure C-2.1. Required marks for acceptable bolt and nut assemblies
(Spec. for Structural Joints Using ASTM A325 or A490 Bolts)
Notes:
1. XYZ represents the manufacturer’s identification mark.
2. ASTM F1852 twist-off-type tension-control bolt
assemblies are also produced with heavy-hex head
that has similar markings.
Page 6 of 6