Beruflich Dokumente
Kultur Dokumente
Si
He
W
W
De
Sh
M
Fo
Bo
Ro
Th
Ne
Po
Po
Di
Be
Ru
PA
20
10
9
12
21
No
To
To
■P
■P
■N
MODEL A
■P
El
H I G H S P E E D R O L L E R G U I D E S
THE FLAGSHIP.HE MODEL A ROLLER GUIDE HAS BEEN THE ELEVATOR INDUSTRY’S GOLD STANDARD FOR
■■■■■■■■■■■■■■■■■■■■
■■■■■■■■■■■■■■■■■■■■
T ELEVATOR RIDE QUALITY FOR OVER 45 YEARS. ITS
DURABILITY, AND EXTENDED APPLICATION RANGE MAKE IT OUR FLAGSHIP PRODUCT.
OUTSTANDING PERFORMANCE, RUGGED
■■■■■■■■■■
■■■■■■■■■■
■■■
■■■
A typical installation:
Passenger Elevator Cabin guides for
1 Mid- to High-Rise Traction Elevator.
Speed: 700 fpm (3,5 m/s).
FEATURES OF THE MODEL A GUIDE: Capacity: 3,500 lbs. (1.600 kg).
1. Six-Wheel Construction improves 3. Precision Ball Bearings guarantee 5. Adjustable Stops enable precise
ride quality and extends the application years of silent use. ELSCO specifies control of the car’s overall postwise float
range. The tandem roller design allows bearings intended for the high RPMs and between the rails. Adjustable stops are a
the guide to “step over” misaligned rail demanding loads of electric motors – standard feature on the Model A guide.
joints with only minimal disturbance to the conditions far more rigorous than typically
cab and its occupants. And by using six seen in elevator applications. This means 6. Durable Structural Components.
wheels where most other guides use just that even after years of operation and tens ELSCO castings are made from high-
three, the Model A can withstand the of millions of cycles, only ELSCO roller tensile-strength ductile iron and aluminum
higher loads associated with service and wheels remain completely silent. Each for an optimal combination of strength,
hospital cars. The added stability also bearing bore is machined to a tolerance of durability, and light weight. High quality
helps compensate for unbalanced five ten-thousandths (.0005) of an inch guide hardware ensures long life and
conditions. (,127mm), and two bearings are pressed ease of adjustment in the field. All
into each wheel by a computer-driven components are inspected and 5
2. Neoprene Rubber Roller Wheels press, ensuring perfect fit and alignment. assembled to exacting standards for a
are specially compounded and rigorously lifetime of reliable performance. 4
tested to ensure a smooth, silent ride. 4. Fully Adjustable Stabilizing
Only genuine ELSCO neoprene wheels Springs allow the car to float between
provide the damping characteristics the rails, eliminating the bumps and ELSCO roller guides and swivel sliding
essential to ride quality, and only genuine vibrations that adversely affect ride quality. guide shoes offer a cost-effective
approach for improving elevator ride
ELSCO wheels are engineered with high 2
quality by reducing the need for expensive,
“memory” characteristics that prevent flat labor-oriented solutions and ongoing
spots. ELSCO rollers are precision ground maintenance. That’s why, to elevator
contractors around the world, the ELSCO
to within .002 inches (,051mm) “Total name is synonymous with quality and
Indicator Reading” for perfect roundness value. At ELSCO, We are ride quality.
and concentricity, then 100% inspected
under stress to ensure a secure bond
between tire and hub.
6
See inside for mounting instructions. Many factors must be considered when
making a guide selection. Please call us to
M
discuss your specific application.
3
410.363.9020
info@elscoguides.com H I G
ELSCO Model A elevator roller guides are MOUNTING BRACKET
designed with adjustment features that provide
BRACKET
superior riding characteristics. The installer can WHEEL CLUSTER ASSEMBLY
easily adjust ELSCO guides to compensate for SPRING
Installation Instructions
Model A
Model A
Mounting Template
adverse operating conditions and to minimize HUB
noise, bumps and vibration. For optimum
performance and longer roller wheel life, we
recommend that elevator rails be properly
aligned and cleaned, and the car balanced
before operation. SPRING
SOLID STOP
ELSCO roller guides are carefully assembled, WASHER
inspected, and packed to arrive in perfect HUB ADJUSTING SCREW ASSEMBLY
condition. When you shipment arrives, inspect 1 2 3 4 5
it carefully for damage and, if appropriate,
immediately file a claim with the carrier. For The Model A Guide includes: a mounting After verifying the proper location of the Position the uppermost roller wheels of wheel Place bracket onto the hub of wheel cluster Position bracket over mounting holds or studs.
best results, read all instructions thoroughly bracket, a wheel cluster assembly, and a bag mounting holes (refer to mounting template), cluster assembly onto the rail, and while assembly. Install mounting hardware (not included with
before proceeding with the installation. containing a spring, a solid stop washer, and a begin installation by inserting the solid stop maintaining pressure against the rail, roll entire guide) as required. Tighten lightly to hold
hub adjusting screw assembly consisting of a washer into the hub. Now, insert the spring assembly upward until face roller wheels are bracket in place prior to final adjustment.
hub adjusting screw with locknut, an adjustable into the hub. firmly seated on the rail.
stop shaft, lock washer and locknut.
GREASE 3/8"
FITTING GAP
HUB ADJUSTING
SCREW AND NUT
3 in
6 7 8 9 10
(70mm
At this point, install the remaining roller guides Be sure guides are aligned properly (as shown) Improper alignment Set 3/8" (10 mm) gap between wheel cluster Securely tighten mounting bolts. Repeat steps 7 Install the hub adjusting screw assembly and
on top and/or beneath the elevator. Lubricate before making any further adjustments. assembly and bracket. Note: Be certain that and 8 on remaining guides before proceeding. nut into bracket. Adjustment of the large screw
the fitting on each guide with general purpose both face roller wheels are firmly seated against This helps assure that the elevator car will be regulates the pressure of the face roller wheels
grease until a small amount appears between the rail while making this adjustment. properly centered between the rails. against the rail.
the hub and the bracket.
SIDE ARM
INCREASE SIDE ARM TRACKING
PRESSURE TIGHTEN ADJUSTING NUT SCREWS
DECREASE
PRESSURE
11 12 13 14 15 16 2 3/8
(60mm
Turn the large hub adjusting screw until roller wheel When properly adjusted, it will be possible to Be certain that both face roller wheel pressure and Adjust side arm roller wheel pressure. Turn side arm At this point, there will be 25 to 50 lbs. (12 to Each pair of side arm roller wheels should track
tire is compressed 1/32" to 1/16" (1 to 2 mm) on the skid the face roller wheel by hand with recommended gap measurement (see step 8) are adjusting nuts until side roller wheels are com- 25 kg) of pressure on each side roller wheel parallel to the face of the rail. The distance from
rail. This represents approximately 25 to 50 lbs. (12 moderate effort. equal for each guide. Caution: This gap meas- pressed 1/32" to 1/16" (1 to 2 mm), and face wheels and the wheels can be skidded by hand on the the edge of each roller wheel to the face edge
to 25 kg) of wheel pressure. Note: If installing urement may now be greater than 3/8" (10 are tracking in the center of the rail. Note: If instal- rail with moderate effort. of the rail should be the same at both the top
guides equipped with polyurethane roller wheels, mm) , but should never exceed 1/2" (12 lation guides equipped with polyurethane wheels, and bottom wheels of each pair. Note: The
refer to step 21 for allowable wheel pressures. mm). Now, tighten adjusting screw locknut. refer to step 21 for allowable wheel pressures. side arm tracking screws are pre-set at the
factory and should need no further adjustment.
SIDE ARM FLOAT ADJUSTMENT
TRACKING SCREW SCREW
FLOAT
ADJUSTMENT
LOCKNUT 21 22
LOCKNUT
(counter clockwise)
INCREASE FLOAT ELSCO’s polyurethane roller wheels are a hard After all adjustments have been made, ride
(95 Shore A durometer) polymer material elevator in both the up and down direction at
(clockwise) TIGHTEN intended for use on lower speed elevators inspection speed to check hoistway clearances.
DECREASE FLOAT when the roller wheel pressures exceed those Check to be sure that all mounting bolts and/or
specified for neoprene composition wheels nuts, and adjustment locknuts are securely
(25 to 50 lbs, or 12 to 25 kg). tightened. Make several more runs at operating
speed, then recheck float, tracking and roller
While polyurethane roller wheels can operate wheel pressures before returning elevator to
17 18 19 20
at pressures up to 300 lbs. (140 kg) per wheel, service.
If it is necessary to adjust side arm tracking, Repeat steps 14 through 17 for each remaining To set postwise float, turn adjustment screw When the desired amount of postwise float is it is advisable to keep static pressure as low as
loosen locknuts and turn side arm tracking roller guide. clockwise until it makes contact with solid stop set, tighten locknut securely while holding float possible to prevent flat spots from forming
screws until top and bottom roller wheels are washer (installed in step 2). At this point, there adjustment screw in place. while the elevator is sitting. Flat spots can
parallel to the face of the rail. Now tighten will be zero postwise float. To increase float, adversely affect ride quality by causing a rough
locknuts. Note: If adjusted correctly, tracking turn adjustment screw counterclockwise. If installing guides equipped with and/or noisy ride. At higher pressures, it may
screws should not restrict float or walking Note: Each full turn equals 1/16" (2 mm). polyurethane roller wheels, refer to not be possible to skid the roller wheels by
beam action of side arm assembly. For best results, set the float at 3/16" to 5/16" step 21 for pertinent information. hand.
(6 mm to 10 mm).
TEM PLATE S HOWN ACTUAL S IZ E
Model A
Mounting Template
5 1/2 in
(140mm)
1 1/16 in (27mm)
11/16 in (17mm)
2 3/4 in
(70mm) 9 3/4 in
(248mm)
3 in FROM FACE OF RAIL
(70mm)
11 3/4 in
(299mm)
MAXIMUM
OVERALL
WIDTH
2 3/8 in
(60mm)
12 3/4 in (324mm)
MAXIMUM OVERALL WIDTH
ON T-160 (15#) RAIL
Model A
Specifications
SPECIFICATIONS