Beruflich Dokumente
Kultur Dokumente
B)
B)
C)
PREPARATION
● Before beginning installation of product, make sure all parts are present. Compare parts with package
contents list and diagram above. If any part is missing or damaged, do not attempt to assemble, install or
operate the product. Contact customer service for replacement part.
● Estimated Assembly Time: 45 - 60 minutes
● Tools Required for Assembly (not included): Flathead screwdriver , Phillips screwdriver, pliers, electrical
tape, wire cutters, safety glasses &8, 60 Watt, Candelabra Base Bulbs.
● Helpful Tools (not included): Wire Strippers.
1 OF 5
INSTALLATION INSTRUCTIONS STYLE NUMBER : RDA5008RY
STEP 1 :
a . Secure the Crossbar onto the Outlet Box with Outlet
Box Screws. Tighten until snug . Outlet Box
Crossbar
Outlet Box
Screw
STEP 2:
* Plier is required on this step .
a . Thread one Hex Nut onto top end of the Nipple .
b . Place one Lock Washer over the top end of the Nipple
and then thread the Nipple into the center lock hole of
the Crossbar . Lock Washer
c . Us ing plier , thread the Hex Nut against the c rossbar Crossbar
Hex Nut
and hand tighten until snug .
d . Thread another Hex Nut onto the bottom end of the
Nipple .
Nipple
Hex Nut
STEP 3 :
a . Adjust the Fixture Chain to your desired length by
removing the links if needed .
* Please note that depends on chain material thickness ,
Nipple
you might be required to use chain pliers to spread links
open . Hex Nut
b . Pull the supply wires through the Fixture Chain alternating
links . And then pull the wires through the following Lock Washer
components in turn :
Canopy Lock Ring , Ceiling Canopy , Canopy Chain Loop, Canopy Chain
Lock Washer , and Nipple . Loop
c . Place Lock Washer over the end of the Nipple and thread
the Canopy Chain Loop onto the end of the Nipple .
d . Using plier , thread the Hex Nut against the Canopy Chain Ceiling
Loop and tighten until snug . Canopy
e . Attach one end of the Fixture Chain onto the Fixture Loop
and attach the another end of the chain onto the Canopy
Chain Loop .
f . Refer to Step 4 - Wire Connections to connect wires . Fixture Chain
g . Push the Ceiling Canopy upward over the Outlet Box .
h . Thread the Canopy Lock Ring onto the Canopy Chain Loop Canopy Lock
Ring
and tighten until snug to secure the Ceiling Canopy .
Fixture Loop
2 OF 5
INSTALLATION INSTRUCTIONS STYLE NUMBER : RDA5008RY
STEP 4 :
* Use Wire Connectors ( not supplied ) to connect the wires .
WHITE WIRE WHITE OR RIBBED
a . Connect the House Ground Wire to the Fixture Ground
Wire. FROM HOUSE FROM FIXTURE
b . Connect the House White Wire to the Fixture Supply Wire
BLACK ( OR RED ) WIRE BLACK OR SMOOTH
( White or Ribbed Side ) .
c . Connect the House Black ( or Red ) Wire to the Fixture FROM HOUSE FROM FIXTURE
Supply Wire ( Black or Smooth Side ).
d . Wrap each connection with approved electrical tape and GROUND WIRE GROUND WIRE
carefully stuff all of the connected wires into the Outlet Box . FROM HOUSE FROM FIXTURE
STEP 5 :
a. Insert eye pin on one end of bead string into pinhole
number 3 and bend over Arm . Pinhole 1 2 Pinhole
b.Insert eye pin on other side of bead string into pinhole Pinhole 3 4 Pinhole
number 4 and bend over Arm.
c.Repeat for pinholes 5 & 6, 7 & 8, and 9 & 10.
d .Repeat steps a- c for remaining 5 Part A bead strings . Arm
Pinhole 5 6 Pinhole
Note: For easy installation of the bead strings, DO NOT Bead String
bend the eye pins until the eye pin from each side of the
arm have been inserted in the same pin hole.
7 8
9 10
11 12
13 14
Top View
STEP 6 :
a Connect Part A U-Drop crystal (without octagon jewel) to
loop at bottom of clear crystal bead in center of Bead Spray 2 Pinhole
String.
Pinhole 1
b.Repeat connection for 5 Part A Crystals in remaining Bead
Crystal C
String sections.
c .Insert the eye pin of Part B Almond shaped crystal into
pinhole 11 and bend downward.
Bead String
d .Repeat for pinhole 12 and continue connecting remaining 5
Crystal A
Almond shaped crystals.
e .Insert eye pin of Part C U-Drop Crystal (with octagon jewel)
in pinhole 1 and bend downward.
f .Repeat for pinhole 2 and continue connecting remaining 5
U-Drop Crystals (with octagon jewels) around top.
Arm
g .Insert eye pin of Part C U-Drop Crystal (with octagon jewel) 11 12
in pinhole 13 and bend downward. 13 14 Crystal B
H.Repeat for pinhole 14 and continue connecting remaining 5
U-Drop Crystals (with octagon jewels) around bottom. Crystal C
3 OF 5
INSTALLATION INSTRUCTIONS STYLE NUMBER : RDA5008RY
STEP 7 :
a . Place Candle Covers over Sockets as shown.
Candle Cover
Socket
STEP 8 :
a . Install correct Bulbs referring to fixture markings and/or labels for maximum wattage.
Your installation is completed now. Restore electricity. Retain this sheet for future reference.
4 OF 5
INSTALLATION INSTRUCTIONS STYLE NUMBER : RDA5008RY
5 OF 5