Beruflich Dokumente
Kultur Dokumente
6 CORPORATE PARKWAY
GOOSE CREEK , SC . 29445 STYLE NUMBER: VTMY8602BN
www . quoizel . com
E Glass Panel 1 pc
C
J
F Bulb Shield 2 pcs
G G9 Bulb 2 pcs
H Socket Collar 2 pcs
D
I Flat Washer 2 pcs
2
J Shade 2 pcs
K
K Socket Collar Tool 1 pc
1
L Allen Wrench 1 pc
L
E
PREPARATION
● Before beginning installation of product, make sure all parts are present. Compare parts with package contents
list and diagram above. If any part is missing or damaged, do not attempt to assemble, install or operate the
product. Contact customer service for replacement part.
● Estimated Assembly Time: 30 - 45 minutes
● Tool Required for Assembly (not included): Flathead screwdriver, Phillips screwdriver, Pliers, Electrical tape,
Wire cutter, Safety glasses and (2) 75W Frosted JCD G9 Bulbs (supplied).
● Helpful Tools (not included): Wire strippers.
1 OF 5
INSTALLATION INSTRUCTIONS STYLE NUMBER: VTMY8602BN
STEP 1: Fig. 1
a. Secure the Crossbar to the Outlet Box with Outlet Box
Screws . Tighten until snug.
Crossbar
STEP 2: Fig. 2
Use Wire Connectors (not supplied) to connect the
wires.
a. Connect the House Ground Wire to the Fixture Ground WHITE OR RIBBED WHITE OR RIBBED
Wire. FROM FIXTURE
FROM HOUSE
b. Connect the House White (or Ribbed) Wire to the
Fixture Supply Wire (Black or Smooth Side).
c. Connect the House Black (or Red) Wire to the Fixture BLACK (OR RED) WIRE BLACK OR SMOOTH
Supply Wire (Black or Smooth Side).
d. Wrap each connection with approved electrical tape FROM HOUSE FROM FIXTURE
and carefully stuff all of the connected wires into the
Outlet Box. GROUND WIRE GROUND WIRE
STEP 3: Fig. 3
a. Place the Backplate over the Crossbar, line up holes on
the side of the Backplate and mounting holes on the Crossbar
folded edge of the Crossbar. Secure by threading Backplate
Mounting Screws into the mounting holes on the
Mounting
Crossbar. Hand-tighten until snug with screwdrivers. Screw
b. Insert the Round Plug into the Plug Receptacle on the
side of the Backplate as shown.
Plug
Receptacle
Round Plug 2
Mounting
Screw
2 OF 5
INSTALLATION INSTRUCTIONS STYLE NUMBER: VTMY8602BN
Bar
Glass (or
Mosaic Panel
EL
Fig. 4A E L Fig. 4B C )P
AN
AN AI
C )P OS
S AI RM
MO O
S(
OR AS
Glass (or Mosaic) Panel S S( GL
F
LA KO
FG C
KO BA
C
BA Middle Slot
Mounting Glass (or
Bracket Mosaic)
Panel
LED
Sliding
Block
Bar
Backplate
LED
STEP 5: Fig. 5
a. Place the Shade and the Flat Washer over the Socket
as shown. Using the Socket Collar Tool, thread the
Socket Collar onto the Socket. Hand-tighten until snug. Socket Collar Tool
Note: There are labels on the Sockets for Bulb Shields Socket Collar
assembly. You might have to remove them while you
Flat Washer
assemble the Shades. Please make notes of the
Sockets sequences before you start it.
Shade
2 Socket
1 Label
3 OF 5
INSTALLATION INSTRUCTIONS STYLE NUMBER: VTMY8602BN
STEP 6:
a. Install the supplied G9 Bulbs into the Socket, referring Fig. 6
Glass (or Mosaic) Panel
to fixture markings and/or labels for maximum wattage.
b. Match the labels on the Bulb Shield and the Socket.
Bulb Shield
Thread the Bulb Shield onto the corresponding Socket 2
to cover G9 Bulbs. Hand tighten until snug. G9 Bulb
(supplied)
STEP 7:
a. Your installation is completed now. Restore electricity. Please note that the G9 Bulbs and the LED lights inside
of the Glass (or Mosaic) P anel can be turned on independently by the wall Switch (Please refer to Step 12).
b. Please retain this instruction sheet for future reference.
STEP 8: Fig. 8
a. Place the Glass Panel onto a flat working surface with
the back facing you. Socket Head Screw
Anticlockwise
b. By using the Allen Wrench (supplied), unscrew Socket
Head Screws at the corners of the frame.
Allen Wrench
BACK
Glass Panel
STEP 9:
a. Remove the side of the Frame and the Glass Panel Fig. 9
carefully as shown.
Remove
Glass Panel
Frame Frame
4 OF 5
INSTALLATION INSTRUCTIONS STYLE NUMBER: VTMY8602BN
STEP 10:
a. Insert the replaced Mosaic Panel into the Frame. Fig. 10
b. Place the side of the Frame back into the Frame as
shown.
Mosaic Panel
Frame “L” Tab
STEP 11:
Fig. 11
a. T hread the Socket Head Screws into the mounting
Clockwise
holes on the “L” Tabs at the corners of the Frame. "L” Tab
Hand-tigthen until snug to secure them.
b. Return to Step 4 for Glass (or Mosaic) Panel assembly.
Allen Wrench
SWITCHING MODE
The switching features of the product allows for you to change your lighting mode from halogen to LED.
STEP 12:
a. Flip the switch “ON” and the halogen lamps illuminates.
ON...
STEP 13:
a. Flip the switch “OFF” to turn off the halogen lamps for
one second.
...One Second
OFF then...
STEP 14:
a. Flip the switch “ON” to turn the LED lamps ON.
...Back ON...
STEP 15:
a. Flip the switch “OFF” to turn off LED lamps.
...OFF
STEP 16:
a. Sequence begins over.
Note: When no switch has occurred for 30 minutes, the halogen lights are programmed to come on first.
5 OF 5