Beruflich Dokumente
Kultur Dokumente
6 CORPORATE PARKWAY
GOOSE CREEK , SC . 29445 STYLE NUMBER: FQ9013MK, FQ9013AW
www . quoizel . com
I Center Stem 1 pc
L
J Fixture Hood 1 pc G
K Shade 1 pc
L Cage 1 pc
H
PREPARATION
● Before beginning installation of product, make sure all parts are present. Compare parts with package contents
list and diagram above. If any part is missing or damaged, do not attempt to assemble, install or operate the
product. Contact customer service for replacement part.
● Estimated Assembly Time: 30 - 45 minutes
● Tool Required for Assembly (not included): Flathead screwdriver, Phillips screwdriver, Pliers, Electrical tape,
Wire cutter, Safety glasses and (4) 60W candelabra base bulbs .
● Helpful Tools (not included): Wire strippers.
1 OF 4
INSTALLATION INSTRUCTIONS STYLE NUMBER: FQ9013MK, FQ9013AW
STEP 1:
a. Place the Shade inside of the Cage as shown. Shade
b. Place Tabs onto the top edge of the Shade and line up Mounting Hole Tab
holes on them and Mounting Holes on the Cage.
c. Using screwdriver, thread Lock Screws into Mounting
Holes and hand-tighten until snug to make sure the Lock
Tabs engage the Shade. Screw
Shade
Cage
Cage
STEP 2:
a. Thread the beaded end of the Stem into the Hex
Coupling inside of the Cage. Hand tighten until snug.
Stem
Cage with
Shade
Hex Coupling
STEP 3 :
a. Install correct Bulbs referring to fixture markings and/or labels for maximum wattage.
2 OF 4
INSTALLATION INSTRUCTIONS STYLE NUMBER: FQ9013MK, FQ9013AW
Center Stem
Cage
STEP 5:
a. Screw the Hex Nut onto the Nipple. Then thread the
Nipple into the Hex Coupling on the top center of the Finial
Fixture Hood. Using pliers, thread the Hex Nut against
the Hex Coupling and hand-tighten until snug. Nipple
b. Thread the Finial onto the top end of the Nipple. Hand- Hex Nut
tighten until snug. Hex Coupling
Fixture Hood
STEP 6:
a. Carefully fit the Post Fitter over the end of the Post (not
supplied), making sure the Post Fitter is fully seated.
b. Mark the drill point for the (3) Mounting Screws, using
(3) Mounting Holes as reference. After marking hole
locations, remove fixture from Post and drill 1/16” pilot Post Fitter
holes for screws.
c. Refer to Step 7 for wire connections. Mounting Screw
d. Coat the top 1” of the Post with Clear Silicone Caulk
(not supplied) and position the Post Fitter onto the
Post. Be sure to seat it completely, aligning the holes in
Post( not supplied)
the Fitter with the 1/16” Pilot Holes drilled into the Post.
e. Secure the fixture to Post with (3) Mounting Screws.
3 OF 4
INSTALLATION INSTRUCTIONS STYLE NUMBER: FQ9013MK, FQ9013AW
STEP 7:
Use Wire Connectors to connect the wires.
WHITE OR RIBBED WHITE OR RIBBED
a. Connect the House Ground Wire to the Fixture Ground
Wire. FROM HOUSE FROM FIXTURE
b. Connect the House White (or Ribbed) Wire to the
Fixture Supply Wire (Black or Smooth Side).
c. Connect the House Black (or Red) Wire to the Fixture BLACK (OR RED) WIRE BLACK OR SMOOTH
Supply Wire (Black or Smooth Side).
FROM HOUSE FROM FIXTURE
d. Wrap each connection with approved electrical tape
and carefully stuff all of the connected wires into the
Outlet Box. GROUND WIRE GROUND WIRE
Your installation is completed now. Restore electricity. Retain this sheet for future reference.
4 OF 4