Beruflich Dokumente
Kultur Dokumente
(5) Threaded Connectors (4) Casters (4) Nuts B B (6) Flathead Phillips Wood L L (6) Flathead Phillips
K (actual size)
X Z (actual size) Screws (actual size) Wood Screws
(actual size)
PARTS ENCLOSED IN CARTON (1) Drawer End - Right Q (1) Drawer End - Left R
PREPARATION:
Carefully lay out all hardware and parts. Check quantities and match to Hardware Bag & Carton Parts Lists. If a part is missing or broken
contact your dealer or Legacy, 812/ 883-3111, (FAX 812-883-1819), http://www.childcraftind.com, for a replacement part or instructional
literature. Before contacting identify your crib. Identification numbers are stamped on the underneath edge of bottom rail of Footboard M ,
Headboard L , crib side O or N or stamped on a label attached to the inside face of Footboard M bottom rail. Record the complete
model identification number now: #__________________. DO NOT SUBSTITUTE PARTS!
STEP 1- DIAGRAM 1: HARDWARE APPLICATION TO HEADBOARD Lay Footboard M and Headboard L down horizontally, (outside
facing down)as shown. Insert an Upper Guide Bushing C and affix
& FOOTBOARD AND ATTACH STATIONARY SIDE. a Flathead Machine Screw B as shown to Footboard M . Note:
use hand screwdriver not battery or electric driver. Tighten but do not overtighten. (Overtightening can cause the Upper Guide Bushing C to
compress down.) The Upper Guide Bushing C must slide freely in groove of the metal track attached to the ends of Dropside O . At this time read
and understand Diagram 4 before proceeding. Test to see that the metal top track will slide freely over Upper Guide Bushing C , if not loosen Flathead
Machine Screw B until the metal top track slides freely, but make sure Upper Guide Bushing C is securely attached. Insert a Lower Guide Pin D
into its receiving hole located on inside face of Footboard M exactly as shown. Follow the same procedure to install the remaining Upper Guide
Bushing C and the Lower Guide Pin D to Headboard L . Lower Guide Pins D will remain loose in their receiving holes. Follow Diagram 1 exactly
for installing Wood Drawer Rail M M and Drawer Cabinet Rail-Right J J to Footboard M using (3) Flathead Phillips Wood Screws B B. Follow
this same process for installing Wood Drawer Rail M M and Drawer Cabinet Rail-Left K K to Headboard L using (3) Flathead Phillips Wood Screws
B B.
B B N
Threaded
ing on its posts. Attach the inserts
loose end of the Stationary
vary)
M N
N
Outside Face
ENLARGED VIEW
G
G
Install this Stretcher first.
Attach both ends before installing
the other Stretcher Y
E G
rl ast.
tche
Stre
all this
Inst
E
Attach this end to Headboard L
Y
following the same process described
for the Footboard M NOTE: Drawer track is not shown (Step 1) to M
allow a clear view of the assembly process.
IV. READ THIS STEP COMPLETELY BEFORE PROCEEDING. Next, lift II. ENLARGED SECTION VIEW
Dropside O approximately two inches (2") vertically. This will put Dropside O Engagement of Metal Top Track
in the proper vertical alignment with the Lower Guide Pin D which will be and Upper
inserted into the Lower Tracks (Right & Left). Guide Bushing C
Flex the bottom end of the corner post on the Dropside side of Footboard M Metal Top Track
away from the Dropside O . The purpose of this process is to create a gap
for the Lower Guide Pins D to pass through so that the Lower Guide Pins IV. ENLARGED VIEW
can be inserted into the long groove of the plastic Lower Tracks. As you
prepare to accomplish this please note the following:
If the Stretcher Assembly Y was not loosened enough (as described in
PREPARATION FOR INSTALLATION OF DROPSIDE in the beginning of
this step) there will not be enough slack to create the necessary gap required
for the Lower Guide Pin D to pass through. Prematurely forcing the pin O C M
through a gap with inadequate clearance could damage the finish on the
Dropside O . If your crib has too small of a gap, then lower Dropside O to its
lowest position and check to verify that preparation at beginning of Step 4
was performed correctly. O
If it was performed correctly, but the gap is still too small, it may be because
the Stretcher Y assembly needs to be pulled away from the bottom rails of
the Footboard M or Headboard L . Check to verify that the Stretchers Y
have been pulled away from the bottom rails.
M
After the Lower Guide Pin D has been installed into the long groove on IV. Then insert Lower Guide Pin D
Footboard M , then repeat this process on Headboard L . After both Lower into long groove in Lower Track (plastic).
Guide Pins D are installed, very carefully and slowly raise the Dropside O
up until it locks into its raised position. Be very careful to watch to ensure that
the Lower Guide Pins D located in the grooves do not slip out during the FLEX
process of raising Dropside O .
Check the function of Dropside O . To lower the Dropside, lift
Refer to Diagram 2. Tighten the (2) Allenhead Bolts G which were installed up on the Dropside top rail with your hand near the middle and
in Step 2 to attach Stretcher Y to Headboard L and Footboard M but were then press in with your knee on the center of the Dropside
loosened in Step 4. Be sure the (2) Allenhead Bolts G are tightened securely. bottom rail. The Dropside will then lower. To lock the Dropside
Check these screws periodically and tighten if needed. in the raised position, just lift it up until it locks into place.
Always verify that both ends of the Dropside are locked in the
raised position whenever child is placed in crib. Only lower
the Dropside when attending to child.
LH01799:01/01 5
STEP 5 - DIAGRAM 5: BUILD UP OF DRAWER. STEP 5B. Install Threaded Connectors K
into Drawer Front S as shown. DO NOT
STEP 5A. Attach Metal Drawer Rail-Right H H to Drawer End- OVERTIGHTEN.
Right Q by matching to pilot holes, affix (3) Flathead Phillips
Wood Screws L L as shown. Repeat this procedure with
Metal Drawer End-Left I I to Drawer End-Left R , again affix K
with the remaining (3) Wood Screws L L. Tighten screws
securely. DO NOT OVERTIGHTEN.
L L
H H
S
L L Drawer
Bottom STEP 5C. Attach Drawer End-Right Q , Drawer End-Left R and
Groove Support Rail V to Drawer Front S . Insert Cam Locks I into their
receiving holes in Support Rail V , Drawer End-Right Q and
Drawer End-Left R , then lower onto the Threaded Connectors
II K . NOTE: Align the large opening in Cam Lock I to receive the
R head of the Threaded Connector K after Cam Locks are inserted
I in receiving holes. Rotate Cam Locks I clockwise 1/2 turn using
a phillips screwdriver.
Receiving Holes
V
R for Cam Locks I
U H H
R
Q
K I
I
J S
S
H H T
Locate the (4) Casters X , insert one into socket in each (Crib mattress will be Sketch A
lower corner post of Headboard L and Footboard M . used as seating for
Caster X design may vary according to your particular Dayed) Refer to Sketch
model. CAUTION: If crib is placed on exceptionally thick A. Follow Installation of
carpet, take care when crib is rolled as casters could Dropside directions,
catch on thick carpet pile and possibly cause breakage (STEP 4), in reverse or-
to lower corner posts of crib. der for the removal of
Dropside O using ex-
treme caution when
Place a purchased mattress on Spring P and crib is
doing so to avoid dam-
ready for use.
age to the finish of your
crib/daybed. Remove
Check periodically to be sure screws and bolts Style may vary
Upper Guide Bushings
(fastening devices) remain tightened as instructed C and Lower Guide
in each step of these assembly instructions. Pins D as directed in Step 1- Diagram 1, in reverse order (NOTE:
it is very important that the Lower Guide Pin D is removed and
After completing crib assembly, and after making yourself stored away from the child because it is not attached to the crib,
aware of the Warnings, Cautions, Cleaning, Storage, and if removed by the child and swallowed, Lower Guide Pin D
Use and Maintenance of crib, store the assembly could be a choking hazard). Store removed Dropside O and
directions in the plastic pouch which was pre-attached to hardware so you will be able to reassemble into a crib if you wish
Spring P . For future referral to assembly directions you to do so in the future. Only use the lowest position placement of
will only need to remove them from the plastic pouch. We Spring P when using as a daybed, (refer to Step 3 - Diagram 3).
caution you not to store excess hardware in plastic pouch Periodically check and tighten (if needed) fastening devices (screws
as this would be a danger to child if retrieved by him/her. and bolts) as instructed. Return the assembly directions to the
plastic pouch attached to the crib spring for future availability.
L
N M
ASSEMBLED CRIB
(STYLE MAY VARY)
R
Q
S
X
•TO LOWER & RAISE CRIB DROPSIDE: To lower lift up on the Dropside top rail with your hand near the center and then press in with your knee on the
center of the Dropside bottom rail. To lock the Dropside in the raised position, lift up from center until it locks into place. Always verify that both ends of
the Dropside are locked in the raised position when child is placed in crib. Only lower Dropside when attending to child.
•MAINTENANCE OF YOUR LEGACY CRIB: Upon completion of assembly be sure screws and bolts (fastening devices) are tightened securely. A periodic
check should be made of fastening devices and tighten if needed. Before each usage or assembly, inspect crib for damaged hardware, loose joints,
missing parts or sharp edges. DO NOT use crib if parts are missing or broken. Ask your Dealer or LEGACY (812/ 883-3111), service@childcraftind.com
for replacement parts and instructional literature if needed. Include Model Identification Number with your request which you recorded on page 1. DO NOT
substitute parts. DO NOT make any alteration to this crib.
•CLEANING INSTRUCTIONS FOR YOUR LEGACY CRIB: Mix together a mild solution of gentle dishwashing liquid and water, apply to crib surface using
a soft clean cloth lightly dampened in the solution. Rinse with clear water again using a soft clean cloth then dry all surfaces thoroughly with a soft dry
cloth. NO ABRASIVE CLEANERS, SCOURING PADS, STEEL WOOL, OR COARSE RAGS SHOULD BE USED TO CLEAN THIS FINE FURNITURE.
•STORAGE AND USE OF YOUR LEGACY CRIB: A printed plastic pouch is attached to the crib spring for the permanent storage of the assembly directions.
After completing the assembly process you are advised to read and be aware of all WARNINGS, CAUTIONS, CLEANING, STORAGE, USE AND MAINTENANCE
notices contained in this set of assembly directions and printed on the plastic pouch attached to crib spring. You will then place the complete set of assembly
directions into the plastic pouch for future referral. We caution you not to place excess hardware in the plastic pouch as it could present danger to a child
if retrieved and it could also puncture crib mattress. When storing crib use CAUTION as extreme temperature or humidity changes could be harmful. Use
CAUTION when a vaporizer is in use, always aim vapor stream away from crib as well as away from any other wood furniture item.
LH01799:01/01
▲
! WARNING
Φ FAILURE TO FOLLOW THESE WARNINGS AND ASSEMBLY INSTRUCTIONS COULD RESULT
7