Beruflich Dokumente
Kultur Dokumente
3.1 ANALYSING THE MAGNETIC EFFECT OF CURRENT-CARRYING CONDUCTOR ELECTROMAGNETS 1. 2. Electromagnetism is the study of the relationship between . and . A bar magnet produces the . around it. Draw the pattern of the magnetic fields produced around a bar magnet below
Magnetic fields of a bar magnet 3. 4. 5. An electromagnet is a ... A simple electromagnet consists of with inside. Soft iron is used because it has the following characteristics; (a) (b) 6. 7. If the soft iron is replaced with a steel core, the steel core becomes a permanent magnet when current flows in the solenoid. Figure 1 shows the action of an electromagnet.
Figure 1
2
8.
Using the diagram above, complete the steps to switch on the magnetism effect.
Switch is closed
9.
The electromagnet uses the magnetic effect of an electric current. A current-carrying wire produces a magnetic field in the region around the wire.
Diagram 2 1. 2.
The magnetic filed lines are concentric circles as shown in figure 2. The direction of magnetic field can be determined using right-hand grip rule. Thumb pointing in the ... The other four fingers show the .. round the wire.
Diagram above shows the symbols of direction of currents out of or into a paper.
Figure 3 1. 2. Figure 3 shows the magnetic field produced by a current in circular coil. The magnetic lines are closest to each other at the centre of the coil with the magnetic field at the centre is the strongest.
The magnetic field pattern by the current in the circular coil 3. The strength of the magnetic field increases when, (a) .... (b) (c) THE MAGNETIC FIELD DUE TO A CURRENT IN A SOLENOID
Figure 4
4
1. 2. 3.
The magnetic filed for a solenoid has a similar pattern to the magnetic field of a bar magnet as shown in figure 4. One end of the solenoid is a North Pole (N) while the other end is a South Pole (S). The polarity at the ends of the solenoid can be determined by;
Looking at the ends of the solenoid. A clockwise indicates a South Pole while an anti-clockwise indicates a North Pole.
Figure 5 1. 2. 3. 4. 5. 6. In an electric bell, the electromagnet is switched on and off very rapidly by making and breaking contact. When you press the switch .. in the coil, creating an The electromagnet then the hammer towards the gong to hit it. When the hammer moves towards the gong, the contact ... The circuit is broken and the current stops flowing. The coil loses its and the hammer returns to its original position, completing the circuit again. In this way, the hammer hits and lifts off from the gong repeatedly, making the bell ring as long as the switch is on.
ELECTROMAGNETIC RELAY
Figure 6 1. 2. In circuit 1 when the switch is closed, current flows and the iron rocker arm is attracted to the electromagnet and pushes the contacts together. Circuit 2 is now switched on. Circuit 2 may have a large current flowing through it to operate powerful motors or very bright lights. When the switch is opened, the electromagnet releases the rocker arm and the spring moves the contact apart. Circuit 2 is now switched off. The advantage of using a relay is that a small current (circuit 1) can be used to switch on and off a circuit with a large current (circuit 2).
3.
TELEPHONE EAR-PIECE
Figure 7 1. A permanent magnet in figure 7 attracts the magnetic alloy diaphragm with a constant force.
7
2. 3. 4.
When the caller at the end of the line talks into the microphone, the ear-piece receives a varying current from the telephone line. The varying current in the coils of the electromagnet changes the strength of the magnetic field and causes the diaphragm to be attracted by a varying force. This causes the diaphragm to vibrate and reproduce the sound.
FACTORS THAT AFFECTS THE STRENGTH OF AN ELECTROMAGNET 1. The strength of the magnetic field can be increased by: (a) (b) (c) (d) (e) (f) 8.1 1. 2. ... .. ..
THE FORCE ON A CURRENT-CARRYING CONDUCTOR IN A MAGNETIC FIELD Electrical motors are found in many household items such as the fan, blender and hairdryer. The rotation is due to forces that are produced by using a current and a magnetic field.
3.
When a current carrying conductor is placed in the magnetic field of a permanent magnet as shown in figure 6, the interaction between the two magnetic fields (magnetic field of the permanent magnet and magnetic field produced by the current-carrying conductor) produced a force on the conductor. This produced a resultant field known as a as shown in figure 7.
4.
A catapult field is produced. The direction of the magnetic filed lines causes the wire to move from the strong magnetic field to the weaker filed Figure 7 5. The relationship between the direction of the current, magnet field and the force acting on the conductor can be easily determined with .
6.
The direction of the force on the conductor is perpendicular to the direction of the current and the direction of the magnetic field.
THE TURNING EFFECT OF A CURRENT-CARRYING COIL IN A MAGNETIC FIELD 1. 2. Consider a current-carrying coil ABCD placed between the poles magnet as shown in the figure below. As the current flows through the coil from A to D, an (1) force acts on the arm CD whereas a . (3) force acts on the arms AB according to Flemings Left Hand rule.
Coil S B 2 3 Magnet D C
1 Carbon brush 4 A
current commutator
3.
The interaction between the magnetic field of the current and the magnetic field of the permanent magnet produced a resultant magnetic field as shown in figure 7.
Figure 7
10
4.
The two forces which are in opposite directions constitute a couple which produces a turning effect and the coil rotates in a clockwise.
Ammeter
Figure 9 1. 2. 3. 4. Figure 9 shows the internal parts of the ammeter or voltmeter. When a current passes through the coil, equal and opposite parallel forces act respectively on the sides of the coil beside the poles of the permanent magnet. This pair of forces causes the coil to rotate until it is stopped by the control springs. When there is no current flow, the forces no longer exist. The control springs bring the coil back to its original position and the pointer goes back to zero deflection.
1. 2. 3.
The direct current motor (d.c motor) uses the turning effect on a current-carrying coil in a magnetic field. A d.c motor consists of a rectangular coil of wire placed between two permanent magnets. Both ends of the coil are soldered to a commutator made of two semicircular copper rings.
11
4.
The use of a commutator is Two carbon brushes are held against the commutator with a slight pressure with the aid of spring. The current flows from the brush P to the coil and out of the coil via the brush Q.
5. 6.
Switch is closed, current flows in the direction abcd. The force on the side ab is downwards The force on the side cd is upwards. These two forces produce a couple which rotates the coil in clockwise direction. Stage 3
The contact between the carbon brushes P and Q with the commutator X and Y is broken. No current flows in the coil therefore no turning force. Stage 4
Horizontal position
Vertical/upright position
Carbon brush P touches Y and carbon brush Q touches X. The current flows in the direction dcba. The force on the side ab is upwards while the force on the side cd is downwards.
The contact between the carbon brushes P and Q with the commutator X and Y is broken. No current flows in the coil therefore no
12
turning force. The above process are repeated and the motor continues to rotate until the current is cut off.
Factors that affect the speed of rotation of an electric motor 1. The magnitude of force acting on a conductor in a magnetic increases by: (a) (b) (c) . . .
13
8.2 1. 2.
ANALYSING ELECTROMAGNETIC INDUCTION The production of an electric current by a _________________________ is called current ____________________________________ ___________________. The induced current is produced when, (a) _________________________________________________________ (b) _________________________________________________________
3.
From the observations of the above activities, it is found that the movement o the of _____________ or the ____________ produces an ____________ in the wire. The existence of the induced current is detected by the galvanometer. The direction of the induced current can be determined using ___________ _____________________________
4.
14
1. 2.
In the above activities, an induced current is produced when there is __________________ produced between the ____________ and the _____________ The induced current produced in this case is due to ___________________ uced _____________________________________________________________
FARADAYS LAW 1. Faradays law state that the _____________________________________ ______________________________________________________ _____________________________________________________________ experience by the conductor. The magnitude of the induced current or e.m.f increases with (a) (b) (c) (d) _________________________________________________________ _________________________________________________________ _________________________________________________________ _________________________________________________________ _________________________________________________________
2.
15
LENZS LAW 1. 2. 3. Lenzs law is used to determine the _____________________________ ________________________________________________ Flemings right hand grip rule is then used to determine the ____________ then _____________________________ _____________________________________________________________________________ _____________________________________________________________ Lenzs Law states that the direction of the induced e.m.f is such that its magnetic effects always ______________________ the change producing.
4.
Lanzs law is an example of the Principle of Conservation of Energy. When the magnet or solenoid is moved against the opposing force, ____________ Therefore __________________ is converted to ______________________
Application of electromagnetic induction 1. 2. A generator is basically the inverse of a motor. A generator consists of many coils of wire wound on an armature that can rotate in a magnetic field. ture The coil is rotated by an external force (e.g. falling water, steam, etc) so that the coil cuts the magnetic field/flux lines as it rotates.
16
DC Generator
17
When coils is at its horizontal position 900 and 2700. The ________________________________ and _____________________________________
When coils is at its vertical position 00, 1800 and 3600. _______________________________________ _______________________________________
AC Generator 1. Two slip rings are used to obtain an alternating current output.
18
2. 3.
When coils is at its horizontal position 900 and 2700. ____________________________________ ______________________________________________________________________________ When coils is at its vertical position 00, 1800 and 3600. __________________________________ ______________________________________________________________________________
19
Characteristics
Effect on a capacitor
Note: The bulb light up for a very short Note: Capacitor allows alternating while after the switch is closed. current but not direct current to pass through. The bulb lights up Note: Both currents produce heating of the filament
Effect on a bulb
20
3.4
ANALYSING TRANSFORMER
1. 2. 3. 4.
In Malaysia, our electricity for domestic supplied at a voltage of 240 V a.c. However, most of home appliances at home use lower than or higer than 240V. A transformer is a device which used to _________ or ____________ the potential difference of an alternating current. It works on the principles of electromagnetic induction.
Operating principle of a transformer 1. A simple transformer consists of two coils wound on a laminated iron core.
A transformer 2.
Symbol
The coil which is connected to the power supply whose voltage is to be raised or lowered is called the primary coil. The supply voltage is called the primary (input) voltage, Vp. The other coil which is connected to the electrical equipment or resistor is called the secondary coil. The voltage across the secondary coil is called the secondary (output) voltage, Vs. The operating principle of a transformer is based on __________________
3.
4.
21
5. 6. 7.
When the alternating current in the primary coil flows, it produced ____________ or ____________. The ______________________________ in the primary coils causes the _________________________________ the secondary coil. The changing of the magnetic flux produces an induced e.m.f across the secondary coil with the same frequency as the electrical supply. Note: The primary coil must be connected to an a.c supply an not d.c supply. This is because an induced e.m.f will not be produced in the secondary coil. The d.c is constant does not create a changing magnetic flux in the secondary coil.
22
EFFICIENCY OF A TRANSFORMER 1. 2. 3. The efficiency of a transformer in normally less than 100% that is the power of the output is less than the power of the input. A transformer transfers electrical energy from one circuit to another circuit by electromagnetic induction. In the process, a fraction of the electrical energy is lost as heat energy. Formula for the efficiency of a transformer:
Ideal Transformer 1. Ideal transformer is no loss of energy in a transformer, all the energy supplied to the primary coil will be transferred to the secondary coil which has an efficiency of 100%.
FACTORS THAT AFFECT THE EFFICIENCY OF A TRANSFORMER AND WAYS TO IMPROVE THE EFFICIENCY OF A TRANSFORMER Factor Resistance of coil Ways to minimise energy losses
23
Examples 1 Transformer that has 2000 turns in its primary coil is used to operate a 12 V, 24 W lamps from the 240 V mains, as shown in figure 1. If energy losses in transformer can be neglected and the lamps is operated at its ratings, find (a) the number of turns in the secondary coil (b) the current in the secondary coil, (c) the current in the primary coil.
24
Examples 2 A transformer enables a 12 V lamp to be used with a 240 V mains supply. If there are 600 turns on the primary coil, calculate (a) the number of turns in the secondary coil, (b) the secondary current if the primary current is 0.5 A. (Assume no energy loss)
Examples 3 A transformer connected to the 240 V mains has 1000 turns on the secondary coil. The efficiency of the transformer is 80% and it is used to light a 12 V, 48 W lamps. If the lamp lights up with normal brightness, calculate (a) the number of turns in the primary coil (b) the primary current
25