Beruflich Dokumente
Kultur Dokumente
050-200208
SERVICE MANUAL
COLOR TELEVISION
29AS42
6. AVOID AN X-RAY
Safety is secured against an X-ray by considering about the cathode-ray tube and the high voltage peripheral circuit, etc. Therefore, when repairing the high voltage peripheral circuit, use the designated parts and make sure not modify the circuit. Repairing except indicates causes rising of high voltage, and it emits an X-ray from the cathoderay tube.
4. PUT PARTS AND WIRES IN THE ORIGINAL POSITION AFTER ASSEMBLING OR WIRING
There are parts which use the insulation material such as a tube or tape for safety, or which are assembled in the condition that these do not contact with the printed board. The inside wiring is designed not to get closer to the pyrogenic parts and high voltage parts. Therefore, put these parts in the original positions.
1. Unplug the plug from the AC outlet. 2. Remove the antenna terminal on TV and turn on the TV. 3. Insulation resistance between the cord plug terminals and the eternal exposure metal [Note 2] should be more than 1M ohm by using the 500V insulation resistance meter [Note 1]. 4. If the insulation resistance is less than 1M ohm, the inspection repair should be required.
[Note 1]
If you have not the 500V insulation resistance meter, use a Tester.
[Note 2]
IMPORTANT
Inferior silicon grease can damage IC's and transistors. When replacing an IC's or transistors, use only specified silicon grease (YG6260M). Remove all old silicon before applying new silicon.
GENERAL SPECIFICATIONS
G-1 TV System CRT CRT Size / Visual Size CRT Type Deflection Magnetic Field BV/BH 27 inch / 676mmV Normal 102 degree +0.45G/0.18G NTSC 2Speaker Front 2.0 x 3.5 Inch 8 ohm 2.5 + 2.5 W 2.0 + 2.0 W No US System M 1Tuner Ohers F-Synth VHF/UHF 75 ohm 2 - 69, 4A, A-5 - A-1, A - I, J - W, W+1 - W+84 45.75MHz 41.25MHz 4.50MHz No Yes Yes 120V AC 60Hz at AC Stand by (at AC) Per Year Power Fuse Safety Radiation X-Radiation Operation Storage 125 W at AC 120 V 60 Hz 3 W at AC 120 V 60 Hz -kWh/Year Yes UL FCC DHHS +5oC ~ +40oC -20oC ~ +60oC Less then 80% RH
G-2
Tuning System
System Destination Tuning System Input Impedance CH Coverage Picture(FP) Sound(FS) FP-FS
Intermediate Frequency Preset CH Stereo/Dual TV Sound Tuner Sound Muting Power Source Power Consumption
G-3
Power
AC DC
G-5 G-6
GENERAL SPECIFICATIONS
G-7 On Screen Display Menu Menu Type Picture Contrast Brightness Color Tint Sharpness Audio Bass Treble Balance BBE On/Off Stable Sound On/Off Set Up PIP SOURCE TV/CABLE(CATV) CH Program Add/Erase Option Language V-chip CH Label Favorite CH Lock Color Stream DVD/DTV Control Level Volume Brightness Contrast Color Tint (NTSC Only) Sharpness Tuning Bass Treble Balance Back Light Stereo,Audio Output,SAP Video Color Stream Channel(TV/Cable) CH Label Game Timer Sleep Timer Sound Mute P-in-P V-chip Rating G-8 G-9 OSD Language Clock and Timer Sleep Timer OSD Language Setting Max Time Step Program(On Tim / Off Tim) more than Yes Icon Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes No Yes Yes No Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes No Yes Yes Yes No Yes Yes Yes Yes Yes Yes Yes Yes No Yes English French English 120 Min 10 Min No No -Min
Spanish
On/Off Timer Wake Up Timer Timer Back-up (at Power Off Mode)
Sec
GENERAL SPECIFICATIONS
G-10 Remote Control Unit Glow in Dark Remocon Format Custom Code Power Source Total Keys Keys RC-DU Yes Toshiba TV:40-BF h 3V UM-4 x 2 pcs 42 Keys Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes No No No No No No No No Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes
Voltage(D.C) UM size x pcs Power 1 2 3 4 5 6 7 8 9 0 100 CH Up CH Down Volume Up Volume Down TV/Caption/Text CH1/CH2 TV/Video(TV/AV) CH RTN/CH ENT(Quick View) Sleep RE Call(Call) Reset Menu/Enter Mute Exit MTS(Audio Select) Fav.Up Fav.Down Set + Set PIP Swap Locate Still PIP CH Up PIP CH Down CH Up(VCR) CH Down(VCR) Pause/Still TV/VCR(VCR) Code FF Rew Rec Play Stop TV VCR Cable
P-in-P Keys
GENERAL SPECIFICATIONS
G-11 Features Auto Degauss Auto Shut Off Canal+ CATV Anti-theft Rental Memory(Last CH) Memory(Last Volume) V-Chip Type BBE Auto Search CH Allocation SAP Just Clock Function CH Label VM Circuit Full OSD Premiere Comb Filter Auto CH Memory Hotel Lock Closed Caption Stable Sound FBT Leak Test Protect CH Lock Video Lock Game Timer Energy Star Favorite CH 1 Tuner P-in-P 2 Tuner P-in-P Owner's Manual Remote Control Unit Rod Antenna Poles Terminal Loop Antenna Terminal U/V Mixer DC Car Cord (Center+) Guarantee Card Warning Sheet Circuit Diagram Antenna Change Plug Service Facility List Important Safety Instruction Dew/AHC Caution Sheet AC Plug Adapter Quick Set-up Sheet Battery UM size x pcs OEM Brand AC Cord AV Cord (2Pin-1Pin) Registration Card (NDL Card) ESP Card PTB Sheet 300 ohm to 75 ohm Antenna Adapter No No No No No No No Yes No No No Yes UM4 size x 2 No No No Yes Yes No No No Yes Yes No Yes No No Yes Yes Yes USA,Toshiba Type No No No Yes No Yes No No No Yes 3 Lines Yes No Yes Yes Yes Yes Yes Yes No Yes No No English / Spanish Yes Yes No
G-12
Accessories
Language W/ Warranty
GENERAL SPECIFICATIONS
G-13 Interface Switch Front Power System Select Main Power SW Sub Power Channel Up Channel Down Volume Up Volume Down AC/DC TV/CATV Selector Degauss Main Power SW Power Stand-by On Timer Video Input Audio Input Other Terminal Video Input(Rear1) Video Input(Rear2) Audio Input(Rear1) Audio Input(Rear2) Video Output Audio Output S- Input Euro Scart Color Stream Diversity Ext Speaker DC Jack 12V(Center +) VHF/UHF Antenna Input AC Outlet Approx. W x D x H (mm) Net (Approx.) Gross (Approx.) Content Material Dimensions W x D x H(mm) Description of Origin Gift Box Material Dimensions W x D x H(mm) Design Description of Origin Drop Test Height (cm) Container Stuffing Yes No No No Yes Yes Yes Yes No No No No Yes No No RCA RCA x 2 No RCA RCA RCA x 2 RCA x 2 RCA RCA x 2 Yes No RCA x 3 No No No F Type No 740 x 500.5 x 560 35kg ( 77.1 lbs) 38Kg ( 83.7 lbs) No ---Sets -/--- x -- x -No Yes Double/Brown 808 x 580 x 655 As per Buyer's Yes Natural Dropping At 1 Corner / 3 Edges / 6 Surfaces 31 162 Sets/40' container
Rear
Indicator
Terminals
Front
Rear
DISASSEMBLY INSTRUCTIONS
1. REMOVAL OF ANODE CAP
Read the following NOTED items before starting work. * After turning the power off there might still be a potential voltage that is very dangerous. When removing the Anode Cap, make sure to discharge the Anode Cap's potential voltage. * Do not use pliers to loosen or tighten the Anode Cap terminal, this may cause the spring to be damaged. REMOVAL 1. Follow the steps as follows to discharge the Anode Cap. (Refer to Fig. 1-1.) Connect one end of an Alligator Clip to the metal part of a flat-blade screwdriver and the other end to ground. While holding the plastic part of the insulated Screwdriver, touch the support of the Anode with the tip of the Screwdriver. A cracking noise will be heard as the voltage is discharged. Location of Anode Cap 3. After one side is removed, pull in the opposite direction to remove the other. NOTE Take care not to damage the Rubber Cap. INSTALLATION 1. Clean the spot where the cap was located with a small amount of alcohol. (Refer to Fig. 1-3.)
Fig. 1-3 GND on the CRT NOTE Confirm that there is no dirt, dust, etc. at the spot where the cap was located. 2. Arrange the wire of the Anode Cap and make sure the wire is not twisted. 3. Turn over the Rubber Cap. (Refer to Fig. 1-4.)
Screwdriver
Fig. 1-1 4. Insert one end of the Anode Support into the anode button, then the other as shown in Fig. 1-5.
2. Flip up the sides of the Rubber Cap in the direction of the arrow and remove one side of the support. (Refer to Fig. 1-2.) Rubber Cap
5. Confirm that the Support is securely connected. 6. Put on the Rubber Cap without moving any parts.
DISASSEMBLY INSTRUCTIONS
2. REMOVAL AND INSTALLATION OF FLAT PACKAGE IC
REMOVAL 1. Put the Masking Tape (cotton tape) around the Flat Package IC to protect other parts from any damage. (Refer to Fig. 2-1.) NOTE Masking is carried out on all the parts located within 10 mm distance from IC leads.
Blower type IC desoldering machine
3. When IC starts moving back and forth easily after desoldering completely, pickup the corner of the IC using a tweezers and remove the IC by moving with the IC desoldering machine. (Refer to Fig. 2-3.) NOTE Some ICs on the PCB are affixed with glue, so be careful not to break or damage the foil of each IC leads or solder lands under the IC when removing it.
IC
Tweezers
Fig. 2-1
IC
2. Heat the IC leads using a blower type IC desoldering machine. (Refer to Fig. 2-2.) NOTE Do not add the rotating and the back and forth directions force on the IC, until IC can move back and forth easily after desoldering the IC leads completely. 4. Peel off the Masking Tape.
Fig. 2-3
5. Absorb the solder left on the pattern using the Braided Shield Wire. (Refer to Fig. 2-4.) NOTE Do not move the Braided Shield Wire in the vertical direction towards the IC pattern.
Soldering Iron
IC
Fig. 2-2
IC pattern
Fig. 2-4
DISASSEMBLY INSTRUCTIONS
INSTALLATION 1. Take care of the polarity of new IC and then install the new IC fitting on the printed circuit pattern. Then solder each lead on the diagonal positions of IC temporarily. (Refer to Fig. 2-5.) 4. When bridge-soldering between terminals and/or the soldering amount are not enough, resolder using a Thin-tip Soldering Iron. (Refer to Fig. 2-8.)
IC
Soldering Iron
Fig. 2-8 5. Finally, confirm the soldering status on four sides of the IC using a magnifying glass. Confirm that no abnormality is found on the soldering position and installation position of the parts around the IC. If some abnormality is found, correct by resoldering. NOTE When the IC leads are bent during soldering and/or repairing, do not repair the bending of leads. If the bending of leads are repaired, the pattern may be damaged. So, be always sure to replace the IC in this case.
Solder temporarily
Solder temporarily
Fig. 2-5 2. Supply the solder from the upper position of IC leads sliding to the lower position of the IC leads. (Refer to Fig. 2-6.)
Solder
Soldering Iron
IC
Fig. 2-6 3. Absorb the solder left on the lead using the Braided Shield Wire. (Refer to Fig. 2-7.) NOTE Do not absorb the solder to excess.
Soldering Iron IC
Fig. 2-7
FIG. 1
Table 1 1. Enter DATA SET mode by setting VOLUME to minimum. 2. Press both VOL. DOWN button on the set and Channel button (6) on the remote control for more than 1 second. ADDRESS and DATA should appear as FIG 1. 3. ADDRESS is now selected and should "blink". Using the VOL. UP/DOWN button on the remote, step through the ADDRESS until required ADDRESS to be changed is reached. 4. Press ENTER to select DATA. When DATA is selected, it will "blink". 5. Again, step through the DATA using VOL. UP/DOWN button until required DATA value has been selected. 6. Pressing ENTER will take you back to ADDRESS for further selection if necessary. 7. Repeat steps 3 to 6 until all data has been checked. 8. When satisfied correct DATA has been entered, turn POWER off (return to STANDBY MODE) to finish DATA input. The unit will now have the correct DATA for the new MEMORY IC.
ELECTRICAL ADJUSTMENTS
1. ADJUSTMENT PROCEDURE
Read and perform these adjustments when repairing the circuits or replacing electrical parts or PCB assemblies. CAUTION Use an isolation transformer when performing any service on this chassis. Before removing the anode cap, discharge electricity because it contains high voltage. When removing a PCB or related component, after unfastening or changing a wire, be sure to put the wire back in its original position. When you exchange IC and Transistor for a heat sink, apply the silicon grease on the contact section of the heat sink. Before applying new silicon grease, remove all the old silicon grease. (Old grease may cause damages to the IC and Transistor.) Prepare the following measurement tools for electrical adjustments. 1. Oscilloscope 2. Digital Voltmeter 3. Multi-sound Generator 4. Pattern Generator On-Screen Display Adjustment 1. In the condition of NO indication on the screen. Press the VOL. DOWN button on the set and the Channel button (9) on the remote control for more than 1 second to appear the adjustment mode on the screen as shown in Fig. 1-1. TV
2. BASIC ADJUSTMENTS
2-1: CONSTANT VOLTAGE 1. Set condition is AV MODE without signal. 2. Connect the digital voltmeter to the TP002. 3. Adjust the VR502 until the digital voltmeter is 135 1V. 2-2: RF AGC 1. Receive the VHF HIGH (63dB). 2. Connect the digital voltmeter between the TP101 and the GND or pin 5 and pin 1 (GND) of CP101. 3. Activate the adjustment mode display of Fig. 1-1 and press the channel button (02) on the remote control to select RF AGC. 4. Press the VOL. UP/DOWN button on the remote control until the digital voltmeter is 2.2V. 2-3: CUT OFF 1. Place the set with Aging Test for more than 15 minutes. 2. Activate the adjustment mode display of Fig. 1-1 and press the channel button (01) on the remote control to select CUT OFF. 3. Adjust the Screen Volume until a dim raster is obtained. 2-4: WHITE BALANCE NOTE: Adjust after performing CUT OFF adjustment. 1. Place the set with Aging Test for more than 10 minutes. 2. Receive the gray scale pattern from the Pattern Generator. 3. Using the remote control, set the brightness and contrast to normal position. 4. Activate the adjustment mode display of Fig. 1-1 and press the channel button (13) on the remote control to select R. BIAS. 5. Press the CH. UP/DOWN button on the remote control to select the R. BIAS, G. BIAS, B. BIAS, B. DRIVE or G. DRIVE. 6. Adjust the VOL. UP/DOWN button on the remote control to whiten the R. BIAS, G. BIAS, B. BIAS, B. DRIVE, and G. DRIVE at each step tone sections equally. 7. Perform the above adjustments 5 and 6 until the white color is looked like a white. 2-5: FOCUS 1. Receive the monoscope pattern. 2. Turn the Focus Volume fully counterclockwise once. 3. Adjust the Focus Volume until picture is distinct. 2-6: HORIZONTAL POSITION 1. Receive the monoscope pattern. 2. Using the remote control, set the brightness and contrast to normal position. 3. Activate the adjustment mode display of Fig. 1-1 and press the channel button (04) on the remote control to select H. POSI. 4. Press the VOL. UP/DOWN button on the remote control until the SHIFT quantity of the OVER SCAN on right and left becomes minimum.
00 OSD
15 Fig. 1-1
3. Use the Channel UP/DOWN button or Channel button (0-9) on the remote control to select the options shown in Fig. 1-2. 4. Press the MENU button on the remote control to end the adjustments.
NO. 00 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 FUNCTION OSD H CUT OFF RF. AGC --H. POSI V. POSI H. SIZE V. SIZE V. CENT V. LIN VS. CORR G. DRV B. DRV R. BIAS G. BIAS B. BIAS BRI. CENT SUBCONT UNI COL MAX NO. 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 FUNCTION UNI COL CENT UNI COL MIN BRI. MAX BRI. MIN COLOR MAX COLOR CENT COLOR MIN TINT SHARPNESS RGB CONTRAST PARABOLA CORR TRAPEZIUM CORR CORNER CORR TOP CORNER CORR BTM V EHT H EHT FM LEVEL LEVEL SEPARATION 1 NO. 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 77 88 FUNCTION SEPARATION 2 TEST STEREO X-RAY V POS U V POS L H POS L H POS R H SIZE V SIZE H POSI R G B BRIGHT COLOR TINT VCO PIP INPUT SELECT READ DATA
Fig. 1-2
ELECTRICAL ADJUSTMENTS
2-7: VERTICAL POSITION 1. Receive the monoscope pattern. 2. Using the remote control, set the brightness and contrast to normal position. 3. Adjust the VR401 until the horizontal line becomes fit to the notch of the shadow mask. 2-8: VERTICAL SIZE 1. Receive the monoscope pattern. 2. Using the remote control, set the brightness and contrast to normal position. 3. Activate the adjustment mode display of Fig. 1-1 and press the channel button (07) on the remote control to select V. SIZE. 4. Press the VOL. UP/DOWN button on the remote control until the SHIFT quantity of the OVER SCAN on upside and downside becomes 9 2%. 2-9: VERTICAL LINEARITY NOTE: Adjust after performing adjustments in section 2-8. After the adjustment of Vertical Linearity, reconfirm the Vertical Position and Vertical Size adjustments. 1. Receive the monoscope pattern. 2. Using the remote control, set the brightness and contrast to normal position. 3. Activate the adjustment mode display of Fig. 1-1 and press the channel button (09) on the remote control to select V. LIN. 4. Press the VOL. UP/DOWN button on the remote control until the SHIFT quantity of the OVER SCAN on upside and downside becomes minimum. 2-10: BRIGHT CENT 1. Receive the monoscope pattern. (RF Input) 2. Using the remote control, set the brightness and contrast to normal position. 3. Activate the adjustment mode display of Fig. 1-1 and press the channel button (16) on the remote control to select "BRI CENT". 4. Press the VOL. UP/DOWN button on the remote control until the white 0% is starting to be visible 5. Receive the monoscope pattern. (Audio Video Input) 6. Press the TV/VIDEO button on the remote control to set to the AV mode. Then perform the above adjustments 2~4. 7. Press the TV/VIDEO button on the remote control to set to the CS mode. 8. Activate the adjustment mode display of Fig. 1-1 and press the channel button (16) on the remote control to select "BRI CENT". 9. Press the VOL. UP/DOWN button on the remote control until the brightness step No. becomes 83. 2-11: SUB TINT/COLOR CENT 1. Receive the color bar pattern. (RF Input) 2. Connect the oscilloscope to TP806. 3. Using the remote control, set the brightness, contrast, color and tint to normal position. 4. Activate the adjustment mode display of Fig. 1-1 and press the channel button (26) on the remote control to select TINT. 5. Press the VOL. UP/DOWN button on the remote control until the section A becomes a straight line (Refer to Fig. 2-1). 6. Connect the oscilloscope to TP804. 7. Press the channel button (24) on the remote control to select COL. CENT. 8. Adjust the VOLTS RANGE VARIABLE knob of the oscilloscope until the range between white 100% and 0% is set to 5 scales on the screen of the oscilloscope. 9. Press the VOL. UP/DOWN button on the remote control until the red color level is adjusted to 110 5% of the white level. (Refer to Fig. 2-2) 10. Receive the color bar pattern. (Audio Video Input) 11. Press the TV/VIDEO button on the remote control to set to the AV mode. Then perform the above adjustments 2~9. 12. Press the TV/VIDEO button on the remote control to set to the CS mode. 13. Activate the adjustment mode display of Fig. 1-1 and press the channel button (26) on the remote control to select TINT. 14 Press the VOL. UP/DOWN button on the remote control until the tint step No. becomes 51. 15. Press the channel button (24) on the remote control to select COL. CENT. 16. Press the VOL. UP/DOWN button on the remote control until the color step No. becomes 55.
White 100%
Red 110%
Fig. 2-2
ELECTRICAL ADJUSTMENTS
2-12: CONTRAST MAX MANUAL 1. Activate the adjustment mode display of Fig. 1-1 and press the channel button (18) on the remote control to select CONT. MAX. 2. Press the VOL. UP/DOWN button on the remote control until the contrast step No. becomes 106. 3. Receive a broadcast and check if the picture is normal. 4. Press the TV/VIDEO button on the remote control to set to the AV mode. Then perform the above adjustments 1~3. 5. Press the TV/VIDEO button on the remote control to set to the CS mode. Then perform the above adjustments 1~3. 2-13: SEPARATION 1, 2 Please do the method (1) or method (2) adjustment. Method (1) 1. Set the multi-sound signal generator for each different Lch and R-ch frequency (Ex. L-ch=2KHz, R-ch=400Hz) and receive the RF. 2. Connect the oscilloscope to the Audio Out Jack. 3. Activate the adjustment mode display of Fig. 1-1 and press the channel button (37) on the remote control to select SEP 1. 4. Press the VOL. UP/DOWN button on the remote control to adjust it until the audio output wave becomes a fine sine wave. 5. Press the CH UP button once the set to SEP 2 mode. Then perform the above adjustment 4. Method (2) 1. Set the multi-sound signal generator L-ch=1KHz, R-ch =Non input and receive the RF. 2. Connect the oscilloscope to the Audio Out Jack (R-ch). 3. Activate the adjustment mode display of Fig. 1-1 and press the channel button (37) on the remote control to select SEP 1. 4. Press the VOL. UP/DOWN button on the remote control to adjust it until the R-ch output becomes minimum. 5. Set the multi-sound signal generator L-ch=Non input, R-ch=1KHz and receive the RF. 6. Connect the oscilloscope to the Audio Out Jack (L-ch). 7. Activate the adjustment mode display of Fig. 1-1 and press the channel button (38) on the remote control to select SEP 2. 8. Press the VOL. UP/DOWN button on the remote control to adjust it until the L-ch output becomes minimum. 2-14: LEVEL 1. Receive the VHF HIGH (70dB). 2. Connect the AC voltmeter to pin 6 of CP101 and the pin 1 (GND) of CP101. 3. Activate the adjustment mode display of Fig. 1-1 and press the channel button (36) on the remote control to select LEVEL. 4. Press the VOL. UP/DOWN button on the remote control until the AC voltmeter is 75 2mV. 2-15: OSD HORIZONTAL 1. Receive the monoscope pattern. 2. Activate the adjustment mode display of Fig. 1-1. 3. Press the VOL. UP/DOWN button on the remote control until the value from the adjustment screen frame to the shadow mask becomes 50 5mm. (Refer to Fig. 2-3) TV
00 OSD 50 mm
15
Fig. 2-3
2-24: Confirmation of Fixed Value (Step No.) Please check if the fixed values of the each adjustment items are set correctly referring below. NO. 05 06 08 10 17 19 20 21 22 23 25 27 28 29 30 31 32 33 34 35 51 52 53 FUNCTION V. POSI H. SIZE V. CENT VS. CORR SUBCONT UNI COL CENT UNI COL MIN BRI. MAX BRI. MIN COLOR MAX COLOR MIN SHARPNESS RGB CONTRAST PARABOLA CORR TRAPEZIUM CORR CORNER CORR TOP CORNER CORR BTM V EHT H EHT FM LEVEL BRIGHT COLOR TINT RF 00 00 32 12 08 64 20 112 32 105 00 30 21 00 00 00 00 00 00 01 ------AV --------09 64 20 112 32 105 00 30 ----------------31 18 30 CS --------06 64 20 112 32 105 00 30 -----------------------
ELECTRICAL ADJUSTMENTS
3. PURITY AND CONVERGENCE ADJUSTMENTS
NOTE 1. Turn the unit on and let it warm up for at least 30 minutes before performing the following adjustments. 2. Place the CRT surface facing east or west to reduce the terrestrial magnetism. 3. Turn ON the unit and demagnetize with a Degauss Coil. 3-1: STATIC CONVERGENCE (ROUGH ADJUSTMENT) 1. Tighten the screw for the magnet. Refer to the adjusted CRT for the position. (Refer to Fig. 3-1) If the deflection yoke and magnet are in one body, untighten the screw for the body. 2. Receive the green raster pattern from the color bar generator. 3. Slide the deflection yoke until it touches the funnel side of the CRT. 4. Adjust center of screen to green, with red and blue on the sides, using the pair of purity magnets. 5. Switch the color bar generator from the green raster pattern to the crosshatch pattern. 6. Combine red and blue of the 3 color crosshatch pattern on the center of the screen by adjusting the pair of 4 pole magnets. 7. Combine red/blue (magenta) and green by adjusting the pair of 6 pole magnets. 8. Adjust the crosshatch pattern to change to white by repeating steps 6 and 7. 3-2: PURITY NOTE Adjust after performing adjustments in section 3-1. 1. Receive the green raster pattern from color bar generator. 2. Adjust the pair of purity magnets to center the color on the screen. Adjust the pair of purity magnets so the color at the ends are equally wide. 3. Move the deflection yoke backward (to neck side) slowly, and stop it at the position when the whole screen is green. 4. Confirm red and blue color. 5. Adjust the slant of the deflection yoke while watching the screen, then tighten the fixing screw. DEFLECTION YOKE DEFLECTION YOKE SCREW MAGNET SCREW 3-3: STATIC CONVERGENCE NOTE Adjust after performing adjustments in section 3-2. 1. Receive the crosshatch pattern from the color bar generator. 2. Combine red and blue of the 3 color crosshatch pattern on the center of the screen by adjusting the pair of 4 pole magnets. 3. Combine red/blue (magenta) and green by adjusting the pair of 6 pole magnets. 3-4: DYNAMIC CONVERGENCE NOTE Adjust after performing adjustments in section 3-3. 1. Adjust the differences around the screen by moving the deflection yoke upward/downward and right/left. (Refer to Fig. 3-2-a) 2. Insert three wedges between the deflection yoke and CRT funnel to fix the deflection yoke. (Refer to Fig. 3-2-b) RGB RGB
R G B
WEDGE
WEDGE
ELECTRICAL ADJUSTMENTS
4. ELECTRICAL ADJUSTMENT PARTS LOCATION GUIDE (WIRING CONNECTION)
CRT PCB
R808 R804 TP804 J801 CP804
CD803
CP805
J708
J704
J703
J701
J702 CP101
CP801A
TP001
CP401
CP502
W011
SPEAKER
VR502
CP702A
CD501 AC IN
CP501
L503
CD702
CRT
J705
J706
J707
MAIN PCB
CP702B
TV BLOCK DIAGRAM
CH DOWN
VOL_DOWN POWER CH UP
41
OS101
1
T501
VOL_UP 10 X101 8MHz
TU001
SOUND+B +B
BLUE B X.OUT 20
IF SDA SCL 11 5 4
SPEAKER SP1001
Q502 12 SWITCHING D 5
AUDIO MUTE 1
Q1001 MUTE 12 7 L R
30 SCL1
31 SDA1
YUV IN
J702
6 4 3
J701
3 4 2
7
IF IN
24 25 43 44 22 21 20 19
YS/YM IN
SDA
U IN
EXT G IN
EXT R IN
SCL
V IN
EXT B IN
18 19 14
7 9
38 V OUT
10 19
ABCL
C IN
Q1503 BUFFER
J703
17 18 20 30
5 6 3 4 2 1
31
34
28
16
15 14
12 42
47
55
18 16 3 Q1507
3 8 10 4 2 6
32 22 25
31
J708
24 23
4 3 2
BUFFER
27 29
J801
8 6 11 7 F 10
15
14
13
CRT V801
Q705
Q704 BUFFER
J704
2 2
BUFFER
HV S F
10
J705
3 2 5
YUV IN
FBT FB401
7 1 9
J706
J707
Q402 H.DRIVE
Q405 H.OUT
W002
W001
D404
TP005
R443
TP004
CD501
D509
C509 R543 D501 C502 D502 D530 L501 D504 C513 C512 D523 R502 B502 R540 B501 R539
HS501
Q502
W006
6.3A125VOR250V
FB401
C535_1
W007
D506
W005
W004
W003
D529
D524 TP002 D407 D405 W012 W013 TH501_1 Q504 R515 D528 R510 S802X W025 W817 R505 Q503 D519 D520 SW103 W065 C533 D513 W080 W077 W071 W068 Q501 W081 W079 W073 W078 W066 C117 W822 R524 R522 W051 W052 D515 IC503 W058 C532 W048 D460 R460 W054 W049 W140 W141 R128 W042 W082 W045 R503 X101 C122 D103 W043 W076 IC103 W063 W069 W072 C111 W169 W120 W118 W115 W112 W116 W111 W156 W155 W154 W153 W150 W148 R112 W136 R159 W117 W157 R160 W139 R635 W146 W813 W808 D615 D612 D608 D611 W802 W130 W114 W119 D602 D603 D604 W129 W093 W094 W188 W189 W113 W125 C625 W207 W208 L604 HS1001 W186 W187 W193 W226 L603 C615 CD701 CD701B W848 W216 R720 W209 C1006 W183 W173 D001 W181 W184 C004 R221 W177 W179 W172 CP101 W180 TP001 W196 W197 W194 W192 W203 W201 C003 IC1001 C1011 W191 W839 C630 L201 IC201 C214 C209 W206 C619 X601 C608 C604 C216 W214 W220 W221 W218 C640 C1501 R1525 L1511 C1502 L1502 L1503 C1518 C1520 L205 D201 CF202 C230 L203 C204 W805 W212 C213 W215 W222 W225 L602 CF203 C203 W205 CF201 W213 C917 L1508 C918 C919 CP702A C924 C211 W224 W219 W223 L204 CD702 R735 C925 C935 C921 C929 L901 W838 J707 W840 C725 W227 C724 C1528 C624 R631 D613 D614 W143 W137 S802Y D606 C616 R608 W142 W217 C612 L601 W147 W152 C305_1 C303 C304_1 L301 W228 IC303 W151 W149 W144 C329_1 C326 D102 D107 W134 W135 W168 W171 W170 W164 W166 W167 C704_1 L302 W163 W161 W834 S801X C315 W162 C1510 W211 L1505 C328_1 CD702 CP702B W138 R106 R133 C123 R137 D108 R512 R508 D516 HS402 B504 W825 W023 W022 VR502 W857 Q507 C501 W026 R554 R553 R002 R001 Q505 RY501 W014 R545 C519
8_1
R432
R43
C426 C413
W821 W807 R507 D505 C531_1 W019 W018 R52 7 W020 Q512 R535 R536 C539 W046 W047 R546 C504 D517 W053 C118 R537
D525
W010
Q405
C431 R406 R428 D514 R424 W057 Q508 W015 W017 D512 C521
C418_2
C425
R439
W008
D510
W024
SOLDER SIDE
L402
C527 W055
R521
W031
CP801A
CD801
W034
CP401_1
R437
VR401
IC502
W059
C417
C427
D403 W029 C403 Q402 C529 Q510 C409 R413 C439 D406 W038 C406 W030 R416 C407 R420 W041 R442 W036 W033 R407 W032 C408 R426 W037 R605 W040 R436 C436 W062 W061 R430 D402 R414
J708
L1510
W035
R429
C715 W103 W101 W100 W099 J704 C1525 CD701A C1530 W106 R1522 W104 W096 W092 W089 W090 W091 W087 W809 W127 W098 R708 CD701 W110 W084 C705 C713 L1512 W088 W086 C146 W108 W095 W133
C714
R517
J703
CP1001
R741 C735 W105 R749 R748 J701 W109 W107 R728 W085 R711 L701 L002 C1007 C1008 C1004 D711 C002 W174 W175 W824 W818 TU001 C1009 R734 C733 R723 R702 J702 R707 W176 R770
R705 W182
IC701
S801Y
W083
R41
C411 IC401
IC504
W011
D503
D531
C524 C541 R511 R412 R547 R533 R532 C554 R126 R513 R516 R101 R104 R134 R116 R114 R142
C405 R417
R115
C107 R525 C526 R415 Q109 Q406 W832 C141 C140 R102 C143 C121 C128 C145 R157 C103 C132 R150 Q460
SOLDER SIDE
IC101
R713 R752 C1533 R1520 R1518 R725 C706 Q709 Q1507 C743 W814 W836 R726 C744 C746 C722 C726 C793 C748 C745 C747 C721 C727 C731 C734 W837 R724 C720 C750 R714 C1526 R751 R721 R636 Q604 Q601 R740 C723 R722 R715 C737 R716 C712 C728 Q701 C708 C707 C739 C738 R004 C001 C730 R1519 R1516 R607 R1013 R1009 Q1001 W842 R1004 R1010 C637_1 R003 R006 R007 C627 R619 C208 C218 C220 R219 R1011 R1003 R217 C221_1 C602 C620 R618 W843 C626 C638 W820 C609 C614 C633 C607 C623 C622 C621 R615 R623 C606 R614 R613 R612 R611 R610 R609 C618 C629 C601 C222 C634 R209 C215 C206 C212 C201 C202 R202 R215 R201 C210 R212 R210 C753 R138 R601 R211 R213 Q201 R205 Q202 Q203 Q204 R220 R218 C227 R223 C229
IC199
R155
R140 R122
R314
R322 R319 R321 C330 R323 R320 C339 C617 R604 R603 C1535 R327 R1505 C1509 C1517 C1519 C1523 R602 C1513 R1506 Q1503 C1504 R750 C605 R747 C729 C1503 C1506 C1507 R203 R204 IC902 R906 R214 R1507 C1505 C1508 R1502 C927 R1503 R1514 C333 C331 C335 R325 C338 R1513 R324 C334 C332 C336 R326 R328 C337 C325
C1531 R1511 C1514 R1504 C1516 R1510 R1528 C1512 R1529 C1515 R1508 C1521 C1527 IC1501 R904
R1509 R1530 R1523 Q1508 Q1504 R1521 R1515 Q1506 R1517 C1522 Q1505 W859 C1524 R905 R1524
R737
R732
C922
0 R8
Q811 Q801 C808 R828 TP804 L804 Q803 TP806 D803 Q812 D801 R830 R815 L802 R808 R821 R811 W003 C820 W804 CP806 CP803 C806 R803 TP805
4 80 R
C805
SOLDER SIDE
L803
R819 R812 D802 CP804 W001 R813 Q802 R809 R802 R829 R810 R817 C804 Q810 C809 W002
R814
C815
J8
01
_2
(MAIN PCB)
TU001 10 NC ENV56DB6G3 3 ADRES 1 AGC 7 BPL 5 SDA 9 BTL 4 SCL 6 V.S 2 NC
13
11 IF
W818
W824
4.9 0
5.0
BT001 R03(AB)E_20_T
1 2 3 4 5 6 7
14
0 NC
0 NC
NC
1.3 NC 6.2 NC
1.3
5.0
5.0
5.0
47 16V 10 KA
30.0
4.6
R111 C123
R006
MTZJ33A
6.3V 470 YK
D001
R007
0.022 M
R127
R130
C004
820
L002 100uH
0.01 B
1K
C001
C002
270
BT002 R03(AB)E_20_T
TM101 SBKMOP006B
270
R004
R003 330K
100
AGC TP001
68 1/4W
0.0022 B
FROM/TO CHROMA/IF AGC SYNC_OUT SCL SDA IF R124 0 0 0 0 0 0 0 4.9 0 NC 5.0 0 R108 2 14 PIP SD P FAIL FSC IN 16 DEGAUSS H CLOCK CONT 17 X-RAY TEST CNVSS X.IN CVIN VHOLD HLF FILT VCC C139 0.01 B R133 10K 1/4W R142 10K X-RAY TEST Q103 KRC102SRTK MODE 5 SDA 5.0 6 SCL 5.0 7 0 8 VCC 5.0 MEMORY IC IC199 S-24C16AFJA-TB-01 C117 50V 50V 1 KA R134 C111 0.47 KA 10K 26 RESET 27 POWER NC 29 0 4.8 5.0 0 5.0 0 4.8 0 0 0 C118 6.3V 2200 YK VCC 1 5.0 GND V.OUT 2 0 D103 1SS133 3 5.0 2.2K R157 10K C109 R109 2.2K C108 68P CH 68P CH R106 100 1/4W R112 100 1/4W 3 4 SDA SCL FROM/TO POWER POWER P.CON+5V TUNER+B AT+5V GND R160 1M R159 C128 0.001 B 19 1 X101 EFOEC8004T4 3 1 21 VSS 22 3.5 24 1.7 1.7 470 1/4W R102 C146 SYNC SEP. 0.3 Q109 0 2SC2412K 0 56P CH C103 KEY 1 KEY 2 X RAY REMOCON ON_TIMER PIP AFT AV2 V SYNC BLUE B GREEN G RED R BLANK NC SDA1 SCL1 37 6 0.3 5.0 5.0 0 2.5 NC 0 0 NC 0 NC R146 R138 1K BBE SW AFT SYNC H SYNC 39 4 4.9 0 38 5 R114 47K R151 4.7K R150 C132 4.7K 820P CH C125 D102 R121 4.7K R122 4.7K R123 4.7K 10 33 1SS133 R141 SCL 4.7K R140 4.7K R139 4.7K D107 1SS133 R144 4.7K 12 11 32 SDA EXT_MUTE SW_VIDEO_OUT FROM/TO SOUND TV_MUTE 10P CH OSD_B OSD_G OSD_R OSD_BLK TUNER_AUDIO_L TUNER_AUDIO_R TO DEFLECTION POWER X-RAY_TEST FROM/TO AV
MICON IC IC101 R119 MTZJ5.6B D108 47K R125 R155 4.7K R156 FROM/TO CHROMA/IF PROTECT AFT_OUT 10K 47K STANDBY_H 1 4.8 4.8 0 AUDIO MUTE EXT MUTE
R126 FROM DEFLECTION V.OUT1 AFC X-RAY SW102 SKHVBED010 VOL DOWN 2.7K
R101
560
2.2K R116
R104
560 SW104 SKHVBED010 POWER SW105 SKHVBED010 SW101 SKHVBED010 SW103 SKHVBED010
CH DOWN
VOL UP
CH UP
31
34
35
36
13
AV1
4.7K 15
28
30
C145 560P W
3
2
X.OUT
0.1 B C122 C121 1K 50V 1 KA C143 100P CH C141 W832 100P CH C140 0.01 B 47P CH
18
25
3
RESET IC IC103 PST600C
20
23
15.9 0 0
W822 VSS E2 4 3 E1 0 2 0 E0 1 0
PCB010 TMA530
NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE
CAUTION: SINCE THESE PARTS MARKED BY CRITICAL FOR SAFETY,USE ONES DESCRIBED IN PARTS LIST ONLY
ARE
ATTENTION: LES PIECES REPAREES PAR UN ETANT DANGEREUSES AN POINT DE VUE SECURITE NUTILISER QUE CELLS DECRITES DANS LA NOMENCLATURE DES PIECES
(MAIN PCB)
8
16V 1000 YK
47uH 0305
L205
C640
10K 1/4W
L601
R604
470 R605
FROM/TO MICON/TUNER 11 SYNC_OUT 10 W820 SDA C617 R607 2.2K B 1 SCL MTZJ5.6B W813 W808 W802 OSD_B OSD_G OSD_R OSD_BLK PROTECT
R747
75 R750
75
D201 MTZJ12B
0.0022 B R215
R601
50V 1 KA
180K
1K
50V 0.22 KA
0.1 B C606
0.1 B
C605
50V 1 KA C633
R203
C211
C614
1.2K
C608
33P CH
0.22 B C601
0.01 B
0.1 B
C215
C634
0.01 B
C607
2.4 0
C216
100
16V 10 KA
R205
9.0
52 V REF
2.4
51 DE-EMPH
3.7
50 DC NF FILTER
2.8
49 EXT AUDIO IN
3.6
48 Y CLAMP FILTER
2.4
47 CVBS LNT IN
2.5
1.9
45
NC 2.4
C609
16V 100 YK
44 U IN
2.5
43 V IN
2.5
42 C IN
2.5
2.7
40 CVBS OUT
1.5
39 DIG GND
38 V OUT
6.0
37 V RAMP
4.9
36 H VCC(9V)
9.0
35 H AFC FILTER
7.1
34 H OUT
4.0
33 SYNC OUT
2.1
32 X-RAY
6.0
30 DIG VDD
3.4
6
TO COMB FILTER FSC_OUT
CVBS EXT IN
EW OUT
2.2K
R204
D606
10V100 YK
16V 47 YK
C604
0.47 B
C616
C210
470
C213
R602
29
NC 2.0
XTAL(3.58MHz)
SIF/H CORR IN
IF VCC(5V)
YS/YM IN
SVM OUT
EXT R IN
EXT G IN
AFT OUT
CW OUT
EXT B IN
R201
RF AGC
IF AGC
R OUT
G OUT
IF IN
IF IN
3.0
4 NC
0 C206
0 0.1 B C218
2.1 12 X601
10
11
2.9
12
1.6
13
5.0
14
4.8
15
4.8
16
4.8
17
18
2.2
19
0.1
20
2.2
21
2.2
22
2.2
23
9.0
24
5.0
25
5.0
26
1.1
27
9.0 R618
28
ABCL IN
YC VCC(5V)
APC FILTER
AUDIO OUT
RGB VCC(9V)
YC GND
1K
EHT IN
B OUT
IK IN
SDA
SCL
6.0 220K
16V 10 KA
0.0022 B
47uH 0305 R609 6.3V 470 YK R610 100 R611 2.7K R612 100 R613 2.7K R614 100
10V 100 YK
0.22 KA C618
EFCT4R5YS5A
0.01 B C619
2.7K
R623
R209
33K C222
CF201
0.1 B C621
0.1 B C622
0.1 B
C620
S802X S802Y
0.01 B
10K
0.01 B C624
FROM POWER
50V 4.7 NA
47uH 0305
0.01 B L602
100uH
33K 50V
0.01 B
C201
C202
R615
C627
L604
2.2K
L603
C625
0.012 B
R202
C203
C623
C626
1K
4
11E1-EIC
MTZJ6.2B
W842
W843
D605
FROM/TO DEFLECTION 13 C220 W805 C221_1 0.01 B 1 2 3 4 IN GNDOUTOUT CF202 TSF5229P3 14 15 V.OUT2 H.OUT ABCL B.OUT G.OUT R.OUT 1SS133 D612 1SS133 D615 1SS133 R631 1SS133 D613 1SS133 D614 1SS133 D611 D608 AFC 150 1/2W
1.2uH
390
IF TUNER_AUDIO_R TUNER_AUDIO_L
220 1/4W
0.0022 B
C935 W840 50V 4.7 KA W838 3.6 V.BLK Q604 2SC2412K 0.047 B C928 2.0 2.2K 0 R636 R635
0.1 B
470 R904
2
SOUND DECORDER IC IC902 AN5829S
NC 24
2.3
NC 23
R905
2.3
22
2.3
21
2.3
DAC
NC 0 5.0 5.0 0 20 19 18 17
GND ZAP IIC Decoder L-R Filter L+R Filter L-R Demod L+R Demod
16
3.7
15
3.6
14
2.6
0.1 B 3.7
C926
C931
470
13
Det SAP
2
R640 PROTECT Q603 2SC2412K 8.9 0 0 R638 1K 4.7K
AGC Matrix
OUT SW
VCA Input
Switch De-Emph (L-R)/SAP 75us Filter Cancel SAPout Offset Expand Cancel Wide Band Offset
2.3
CAUTION: DIGITAL TRANSISTOR NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE
1 0
4 2.2 C919
6 0.4
Vcc
8 2.4
9 2.4
10 0.4 C930
NC2.3 NC2.3
5.1
50V 4.7 KA
50V 4.7 KA
50V 3.3 KA
0.022 B C925
10V 100 YK
1
220K C917 R906
16V 10 KA C922
TUNER AUDIO SIGNAL TUNER VIDEO SIGNAL LUMINANCE SIGNAL COLOR SIGNAL DEFLECTION SIGNAL R.SIGNAL G.SIGNAL B.SIGNAL
F G
PCB010 TMA530
0.022 B C929
C918
C924
(MAIN PCB)
V.OUTPUT IC IC401 LA78041 + THERMAL PROTECTION 2.2K 1/4W AMP R442
5 12.0
6 25.0 17
16 35V 100 YK
11E1-EIC C407
D402
16V 47 YK
C436
C411 D403 R460 1K 1/4W 1SS133 560P CH R413 D460 C405 R414 R415 500V10P SL 25V 2200 YK 2.2K 1/2W R408 220 1/2W 820 MTZJ30B MTZJ30B
R421
R425
680 1/2W
680 1/2W
C417
R424
V.POSI
6
FROM POWER P.CON+5V P.CON+9V GND +B AT+12V
1 1/2W
C406
R437
4.9 0
D410
V801 A68AJB82X10
R416
R420
C409
2.7 1/2W
50V 10 YK
TO DY
CP401_1 A2361WV2-4P
9 10 8 6 11
4 3 2 1
6
R G B 5 7 1
680 1/2W
L402 R439 ELH5L4113 21 C418_2 250V 0.47 PMS CMPP FB401 +B TP002 2.8 1 13.1 6 W807 W821 108.0 2 105.0 9 0 10 R452 D414 11E1-EIC R410 150 2W D415 11E1-EIC R432 MTZJ9.1B 8.2K 1/2W D405 RGP15J COL E180 B+ 3227009R 1K 1W C425
TO CRT
CD803 CU822501
CD805 CU822501
T401 ETH14Y47AY 4 5 1
C402
50V 47 YK
R406
100 1/4W
C403
C431
C420
17.3
1.25KV 0.016
2KV 0.001 R
5
ANORD
HV
TO CRT AFC HEA TER F S GND 0 11 ABL 8.1 7 68K 1/2W C427 100V 0.1 MKT R443 FORCUS SCREEN
180 1W
D404
R438_1
X-RAY
15.9 10.9
AFC C439 V.OUT2 H.OUT ABCL B.OUT R.OUT G.OUT 0.001 B V.OUT1
C426
FROM/TO CHROMA/IF
250V 33 YK
15.9
0.22
1W
D407
MTZJ5.6B
100V 22 YK
D406
R426
TP005 35V 1000 YK TO CRT CP801A (CP805) B2013H02-10P 180V NC NC NC NC GND HEATER B.OUT R.OUT G.OUT P.CON+9V GND 1 2 3 4 5 6 7 8 9 10 CD801 CU2A3601
C430
TP004
C413
PCB010 TMA530
1
NOTE: THE DC VOLTAGE AT EACH PART WAS MEASURED
WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL.
NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE
CAUTION: SINCE THESE PARTS MARKED BY CRITICAL FOR SAFETY,USE ONES DESCRIBED IN PARTS LIST ONLY
ARE
ATTENTION: LES PIECES REPAREES PAR UN ETANT DANGEREUSES AN POINT DE VUE SECURITE NUTILISER QUE CELLS DECRITES DANS LA NOMENCLATURE DES PIECES
NOTE: THE RESISTOR MARKED F IS FUSE RESISTOR. THE ALUMI ELECTROLYTIC CAPACITOR MARKED NP IS NON POLAR ONE. F G H
(MAIN PCB)
CAUTION: FOR CONTINUED PROTECTION AGAINST FIRE HAZARD, REPLACE ONLY WITH THE SAME TYPE FUSE
6.3A 125V(F501)
ATTENTION: POUR UNE PROTECTION CONTINUE LES RISQUES DINCEIE NUTILISER QUE DES FUSIBLE DE MEME TYPE
6.3A 125V(F501)
7
R515 10K 1/4W TO CHROMA/IF P.CON+9V P.CON+5V AT+5V GND
RY501 ALKS321 2 DEGAUSS COIL L503 8R270008 1 2 1 3 CP502 A1561WV2-2P 1 2.7M 1/2W +-10%
250V 0.001 KY
C513
D505 35V 1000 YK 21DQ09N-FC4 R501 1N4005-EIC D530 1.2 7W 1N4005-EIC R541_1 MTZJ18B 1.2M 1/4W 1.2M 1/4W R539 0.22 1W C501
R517 1 2W
TO SOUND C526 0.001 B R537 135.0 C539 R505 150K 1/4W +B SW. Q503 2SA1371 135.0 135.0 10K 1/4W 134.3 220K 1/4W SOUND+B P.CON+9V SOUND_GND P.CON+5V GND
1N4005-EIC D527
1N4005-EIC
D501
R500
D502
TH501_1 250V 0.22 ECQUL 120V 60Hz CD501 2 2 ZPB45BL3R0A 1.5M 1/2W C505_1 R518 CP501 A3963WV2-3PD WHITE F501 1 1 BLACK
200V 470 UP
R540
D504
BLADE WIDE
D503
3 1
4 2
C506_1
D523
250V
WHITE BLACK
T501
8140065S
B504
D510
50.0 141.6
8 P1 7 9 NC 25.0 W825 10
R507
6.3A125V FH501 FH502 EYF-52BC EYF-52BC 51MS 6.3A L B502 6.3A 125V BL02RN1-R62T2 B501
HS501 763WAA0238
0 40.0
6 125.0 5
0
11 P2 240.0 12
TO AV P.CON+9V GND
R525 D511 R546 50V 10 YK C504 R524 2.2K 1/4W D515 MTZJ15B R503 4.3 10K 1/4W
BL02RN1-R62 SWITCHING Q502 131.7 D 2SK3326(2) G 6.88 9.9 0.12 S 0.5 SWITCHING Q514 KTC3203_Y 0 R542 D507 1SS133 R544 2KV 680P RR 13 R502 C512
0 138.9
3 20.0 14
C535_1
47K
5.0
26.0 15
0 16
4
FEED BACK IC504 LTV-817M-VB 16.3
8.9 5.6
0.15 1W 1.5
IN +5V SW Q510 2SD734 8.9 8.7 9.5 390 1/4W C529 1 8.7
GND 2
OUT 3 5.0
0.1 B
C541
270 1/4W R545 D524 D513 1K 1/4W MTZJ5.6B C533 C531_1 150 1/4W 1SS133 25V 470 YK D506 1N4937 25V 47 YK 16V 10 KA R512 D509 MTZJ18B 1K 1/2W C509 R543
0 R522
10.7
2 9.7
R520
C554 0.022 B 9.7 FEED BACK SWITCHING Q507 5.7 KTC3198 R532 1.5K
763WAA0200
3
W817
6.3
GND1 250V 0.0022 KY +12V SW Q508 KTA1273_Y 12.1 R511 22K 16V 2200 YK 1K 1/2W C527 R519 11.3 11.9 IN 1 11.3 GND 2 OUT 1SS133 D519 R533 270 R547 REG.+9V IC IC502 KIA7809API 100
27K 1/2W
R553
MTZJ8.2B
D525
C522
D512 SB290S
W857
R510
VR502 22K
MTZJ5.6B
CAUTION:
C528
C530
10V 1000 YK
+B ADJ
D528
1000 16V YK
3 0 9.0 R521 27 2W
5.0
W803
NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE
CAUTION: SINCE THESE PARTS MARKED BY CRITICAL FOR SAFETY,USE ONES DESCRIBED IN PARTS LIST ONLY
ARE
ATTENTION: LES PIECES REPAREES PAR UN ETANT DANGEREUSES AN POINT DE VUE SECURITE NUTILISER QUE CELLS DECRITES DANS LA NOMENCLATURE DES PIECES
NOTE: THE RESISTOR MARKED F IS FUSE RESISTOR. THE ALUMI ELECTROLYTIC CAPACITOR MARKED NP IS NON POLAR ONE. F G H
(MAIN PCB)
16V 47 YK R322
100P CH C337
100P CH
R321
4.7K
C326
1.5K
C336
C331 C332 0.022 B 5.0 3 4 1.8K + VR3 S1 0.47 B 4.8 5 S3 S5 VR5 4.7 6 S7 4.8 0 7 8 TONE AMP1 + 6.5K CONTROL LOGIC + TONE VR6 AMP2 15 14 13 4.8 0 5.0 S8 S4 S6 4.8 9 4.7
5.0 2
5.0 136K
SIMAMP1 VOLAMP16.5K REF VOLAMP2 REF SIMAMP2 6.5K VR2 + 136K 1.8K VR4 20 19 18 17 16 + + S2 10.0 5.0 C329_1 5.0 16V 22 KA 5.0 C330 4.8 C333
VR1
16V
6.5K
C304_1
22 KANP
10
6
12 4.9 11
4.7
0.022 B 0.47 B
C339 0.01 B
R325 1.8K
C303 16V 47 YK
5
R323 1.5K
47uH C305_1
16V 220 YK
S801Y
S801X
TV_MUTE SOUND AMP IC IC1001 AN5276 + + FROM POWER P.CON+5V P.CON+9V SOUND+B GND CH1 NC IN 1 2 0 NC ATT. + CH2 OUT 0 RIPPLE FILTER CH2 GND RF IN 3 4 5 0 13.9 0 25V 100 YK C1011 + ATT.CONT. 25 NC 6 0 MUTE 8 6.7 GND 9 0.7 STAND CH1 VCC -BY OUT 10 11 12 0 14.9 12.1 6.7 24
0.01 B
22uH C315
L302
C325
0.001 B
C338
SOUND_GND
R1011
10K
16V 2200 YK
R1010
10K
C1009
C1004
25V 1000 YK
C1003
R1013 10K C1006 220P B R1009 10K 3.6 MUTE Q1001 KRC111SRTK 0 50V 2.2 KA 16V 22 KA HS1001 763WAA0215 NC C1008 0 C1007
W/CONECTOR.2SPEAKER CP1001 A2502WV2-4P 4 3 27 2 1 4 3 2 1 (R) (L) SP1001 S0509F12-C 8 OHM 2.5W SPEAKER 8 OHM 2.5W
26
W809
PCB010 TMA530
CAUTION: DIGITAL TRANSISTOR NOTE: THE DC VOLTAGE AT EACH PART WAS MEASURED
WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL.
NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE
CAUTION: SINCE THESE PARTS MARKED BY CRITICAL FOR SAFETY,USE ONES DESCRIBED IN PARTS LIST ONLY
ARE
ATTENTION: LES PIECES REPAREES PAR UN ETANT DANGEREUSES AN POINT DE VUE SECURITE NUTILISER QUE CELLS DECRITES DANS LA NOMENCLATURE DES PIECES
AUDIO SIGNAL
AV SCHEMATIC DIAGRAM
8
(MAIN PCB)
FROM/TO CHROMA/IF CD701A CH243001 4 3 2 1
H1
75 1/4W
R708
H1
29
H2
28
7
A/V_OUT(REAR) J708 MSP-213V2-432_PBSN
H1 NC H1 H2
SW_A_OUT_L2
FROM POWER P.CON+9V GND C714 FROM/TO COMB FILTER W837 34 SW_VIDEO_OUT Y_V_OUT_COMB C_V_OUT_COMB 16V 10 KA
SW_A_OUT_R2
R726
R724
3.3K
270
C715
R713
4.6 8P CH 0
H1 NC H1 H2
5
AV SW IC IC701 MM1311AD C708 TUNER_AUDIO_L TUNER_AUDIO_R TUNER_VIDEO L701 100uH 0607 0.1 B C707 C730 1B 5.2 5.4 1 B 32 5.4 1 4.7 2 5.4 3 4.8 C721 29 4 C720 33P CH 2.5 BUFFER Q701 2SC2412K C729 Y_V_OUT_SW R740 0.47 B 31 9.0 3.1 R721 1.2K 2.5 1.2K 28 C723 150P CH 0.01 B 5 5.4 Vcc S1 BIAS 1 B C731 9.0 27 6 4.0 C735 26 7 16V 22 KA 4.8 25 8 5.8 24 9 4.7 4.7 4.8 4.7 C745 5.4 4.8 10 5.4 C734 4.8 0 C737 20 FROM/TO MICON/TUNER EXT_MUTE KA SW_VIDEO_OUT SCL SDA W814 C741 W836 13 4.7 0 5.0 4.8 5.4 5.4 C793 1 B C738 1 B C739 R716 470 0.01 B 1 B C722 1 B C746 1 B 4.7 0 W833
2 3
0.0056 B C727
0.0056 B R702
FROM/TO CHROMA/IF
C_V_OUT_SW
3.9K 1/4W C748 0.1 B R715 D711 MTZJ6.2B C747 1 B R749 3.9K 1/4W R717 470 1/4W R748 3.9K 1/4W R770 10K 1/4W 470 1/4W R734 1K
30
30
75 1/4W
1 B C712
31
C726
C728
R723
75 1/4W 75 1/4W
R705
R707
4
S-JACK J702 YKF51-5503
32 33
FRONT-VIDEO J705 AV1-06D-3 H 2 R720 180K R737 180K R730 100 1/4W 1 E
SW_AUDIO-R
23
FRONT-AUDIO.L J706 AV1-06D-4 R732 3.9K 0.0056 B C742 FRONT-AUDIO.R J707 AV1-06DS-2
NC
22
11
21
12
50V 1 KA
F_VIDEO F_AUDIO_L
R727
18
15
33P CH
75 1/4W C753
3.3
10V 470 YK
1 B 33P CH R735
17
16
5.0
3 4 5
3 4 5
F_AUDIO_R
R738
220K
C740
50V
FRONT.AUDIO.L
FRONT.AUDIO.L
0.0056 B
FRONT.VIDEO
FRONT.VIDEO
50V 1 KA
3.9K
C704_1
CP702A A2001WV2-5P
CD702 CU252002
1K
R731
220K
19
14
CP702B B2013H02-5P
C725
R739
GND
S2
8.8
C724
PCB010 TMA530
PCB170 TEAA92
WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL.
NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE
AUDIO SIGNAL TUNER AUDIO SIGNAL TUNER VIDEO SIGNAL COLOR SIGNAL LUMINANCE SIGNAL
F G H
(MAIM PCB)
1.2K 1/4W
R1511
1.2K
R1525
L1511 R1517 R1513 470 15uH 0305 16V 100 YK C1531 0.01 B C1528 9.0 2.5 2.0 BUFFER Q1508 2SC2412K C1535 R1530 Y_V_OUT_COMB 470 0.1 B 47
L1505 W848 R1505 15uH 0305 8.3 W859 6.8K C1524 5.0 1.0 1.0 100P CH C1517 R1506 R1507 BUFFER Q1503 2SC2412K C1519 C1522 8P CH 20P CH 2.2 1.6 R1514
R1503
100
6
6.3V 100 YK 0.01 B C1510 C1509
8.9 8.3 BUFFER Q1506 BUFFER Q1505 2.5 2SA1037AK 2SC2412K R1515 R1521 470 1K
FROM/TO AV
C1513 0.1 B
470
COMB FILTER IC IC1501 LA76600M-TLM C1504 2.6 CIN INSEL YIN2 GND AVCC DVCC SAND CASTLE COUT OUTSEL YOUT GND YIN1 AFC RD 1 4.9 4.2 0 4 4.9 5 4.9 C1502 100 YK 6.3V C1503 0.1 B 6 C1506 4.0 7 0.1 B C1507 2.1 PHASE DET FSC_IN GND GND 8 0.1 B 0 9 3 2 2.4 18
5
R1502 100
0.1 B
0 17 3.4 16 0 15 C1514 R1528 0.1 B R1529 C1521 0.1 B 100uH C1520 0305 R1509 L1508 47K 2.9 14 3.6 13
C1505 1 B 0.1 B
C1501
C1508
6.3V 100 YK
16V 100 YK
12
82K C1516 4.7K R1504 C1518 0.1 B 9.5 C1512 8.2K 50V 1 KA 0.9 0.1 B C1515 R1524 C1527
FROM CHROMA/IF R1523 100 C1523 FSC_OUT 0.001 B L1510 15uH 0305
11
470P CH
0 10
220
47K
0.1 B
R1510
R1518
0.01 B
C1525
5.0
27K
R1519
C1533
C1530
R1522 1K 1/4W
PCB010 TMA530
NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE
(CRT PCB)
FROM DEFLECTION CP805_1 (CP801A) A2001WV2-10P 10 9 8 7 6 5 4 3 2 1 GND P.CON+9V G.OUT R.OUT B.OUT HEATER GND NC NC 180V C813 0.0022 M D808 1SS133 NC NC GND
TP804
150uH
L802
12K 2W
R804
37
RED/GREEN AMP Q801 123.5 2SC2621 7.8 220 1/4W 7.3 R813
D801 1SS133 R801 R810 100 1.8K 1/4W 1/4W 390P B C804 3.0 7.3 RED/GREEN AMP Q810 2SC1740S TP 2.4 R817 270 1/4W 117.0 0 6 5 4
W802 W803
150uH 12K 2W
D807 1SS133
1
0 38 R829 2.7K 1/4W
F
J801_2 ISHS53S
R814
L803
220 1/4W
D802 1SS133 R802 330P B C815 R812 1.8K 1/4W C805 100 1/4W 3.0 390P B
W804
500V 0.001 B
12K 2W
C820
R808
L804
150uH
39
119.7 7.3
D803 1SS133 R803 3.1 7.3 2.5 270 1/4W BLUE AMP Q812 2SC1740S TP
1.8K 1/4W
FROM DEFLECTION
CP806 A2361WV2-2P
CP803 A2361WV2-2P
005P-2100 FOCUS
SCREEN
GND
GND
GND
GND
CP804
PCB110 TCA389
NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE
CAUTION: SINCE THESE PARTS MARKED BY CRITICAL FOR SAFETY,USE ONES DESCRIBED IN PARTS LIST ONLY
ARE
ATTENTION: LES PIECES REPAREES PAR UN ETANT DANGEREUSES AN POINT DE VUE SECURITE NUTILISER QUE CELLS DECRITES DANS LA NOMENCLATURE DES PIECES
WAVEFORMS
MICON/TUNER
1 2.0V 50ns/div
500mV 10s/div
11 500mV 50s/div
2.0V 50ns/div
200mV 10s/div
12 100mV 100ns/div
3 2.0V 50s/div
1.0V 5ms/div
13
1.0V 20s/div
2.0V 50s/div
9 1.0V 20s/div
14 1.0V 20s/div
CHROMA/IF
200mV 10s/div
10 2.0V 20s/div
15 1.0V 20s/div
NOTE: The following waveforms were measured at the point of the corresponding balloon number in the schematic diagram.
WAVEFORMS
DEFLECTION
16 1.0V 5ms/div
21 200V 20s/div
26 500mV 1ms/div
SOUND
17 10V 5ms/div
22 1.0V 2ms/div
27 500mV 1ms/div
AV
18 10V 5ms/div
23 1.0V 2ms/div
28 200mV 20s/div
19 50V 20s/div
24 20mV 1ms/div
29 200mV 20s/div
20 2.0V 20s/div
25 20mV 1ms/div
30 100mV 10s/div
NOTE: The following waveforms were measured at the point of the corresponding balloon number in the schematic diagram.
WAVEFORMS
31 500mV 10s/div
38 50V 10s/div
32 1.0V 1ms/div
39 50V 10s/div
33 1.0V 1ms/div
34 1.0V 10s/div
CRT
37 50V 10s/div
NOTE: The following waveforms were measured at the point of the corresponding balloon number in the schematic diagram.
201 201
114
201 105 202 104 104 202 PCB110 (CRT PCB) 108
201
114
202 203 103 205 PCB010 (MAIN PCB) 205 204 205 206 206 102 204
204
204 203 203 113 204 110 204 PCB170 (VIDEO JACK PCB) 106 112
109
Reference No.
A3L509E720 771WPA0263 899EFBA002 899HV3T000 741WUA0021 701APJA109 712APBA003 702APA0134 711WPA0168 713WPA0202 722549A106 7260000306 735WPBA416 762WPA0009 723549A007 8117540B04 8111J50D05 8109630802 8110630A04 8109I30A04 8107630804 791AHA0024 792AHA0087 792AHA0088 793ACDA158 A3L509E975 J3K11302 J3L50901 JA4LD200
Description
CABINET,FRONT ASSY PLATE,JACK WIRING-CLIP HOLDER,ANODE WIRE SPRING,EARTH CABINET,FRONT DOOR CABINET,BACK PLATE,FRONT GLASS,LED SHEET,RATING SHEET,CAUTION BUTTON ASS'Y HOLDER,CRT WIRE AV LABEL SCREW,TAPPING(B0) TRUSS SCREW,TAPPING(A) GW22 SCREW,TAP TITE(B) BRAZIER SCREW,TAP TITE(P) BRAZIER SCREW,TAP TITE(B) WH7 SCREW,TAP TITE(S) BRAZIER 4x20 5x35 3x8 3x10 3x10 3x8
FILM BAG PACKAGE,TOP PACKAGE,BOTTOM GIFT BOX INSTRUCTION BOOK KIT GUARANTEE CARD INSTRUCTION BOOK POLYBAG,INSTRUCTION(RED CAUTION)
Description
1M OHM 1/6W 150 OHM 2W 3.9 OHM 1/2W 2.7 OHM 1/2W 4.7K OHM 1/6W 18K OHM 1/6W 0.22 OHM 1W 1K OHM 1W 15K OHM 1/6W 180 OHM 1W 2.7M OHM 1/2W 1.2 OHM 7W 1.2 OHM 7W 330 OHM 2W 10K OHM 1/4W 10K OHM 1/4W 1 OHM 2W 1.5M OHM 1/2W 27 OHM 2W 27 OHM 2W 0.68 OHM 2W 0.22 OHM 1W 0.15 OHM 1W 100K OHM 1/2W 12K OHM 2W 12K OHM 2W 12K OHM 2W 2200 UF 25V 1000 UF 35V 0.47 UF 250V PMS 0.47 UF 200V FHS 0.016 UF 1.25KV 0.001 UF 2KV R 33 UF 250V 22 UF 100V 1000 UF 35V 0.001 UF 2KV B 0.001 UF 2KV B 10 UF 50V 0.22 UF 250V ECQUL 0.22UF 275V PHE840 0.1 UF 250V ECQUL 0.1 UF 275V PHE840 470 UF 200V 47 UF 25V 0.001 UF 250V 820 PF 2KV RR 0.001 UF 250V 220 UF 160V 0.0022UF 250V 2200 UF 16V 470 UF 25V 680 PF 2KV RR 680 PF 2KV R 0.001 UF 2KV B 1000 UF 25V 2200 UF 16V 2200 UF 16V MTZJ33A T-77 1SS133T-77 1SS133T-77 1SS133T-77 MTZJ5.6B T-77 SLR-342VCT32 MTZJ12B T-77 11E1-EIC MTZJ30B T-77 MTZJ9.1B T-77 RGP15J-G23 MTZJ5.6B T-77 AU02A-EIC MTZJ30B T-77 AU02A-EIC 11E1-EIC 11E1-EIC
! ! ! ! ! ! ! ! ! ! !
or
! R502 R503 ! R505 ! R517 ! R518 ! R521 ! R522 ! R527 ! R541 ! R542 ! R554 ! R804 ! R806 ! R808 ! C408 ! C413 C418 ! C420 C425 ! C426 ! C430 ! C501 ! C502 ! C503 ! C504 ! C505 ! C506 ! C507 ! C509 ! C513 C517 ! C519 ! C521 ! C522 ! C527 ! C531 C535 C808 C1003 C1004 C1009 D001 D102 D103 D107 D108 D109 D201 D402 D403 D404 D405 D406 D407 D410 D411 D414 D415
CAPACITORS
or
or or
or
DIODES
DIODE,ZENER DIODE,SILICON DIODE,SILICON DIODE,SILICON DIODE,ZENER LED DIODE,ZENER DIODE,SILICON DIODE,ZENER DIODE,ZENER DIODE,SILICON DIODE,ZENER DIODE,SILICON DIODE,ZENER DIODE,SILICON DIODE,SILICON DIODE,SILICON
! ! ! !
Description
1SS133T-77 1N4005-EIC 1N4005-EIC 1N4005-EIC 1N4005-EIC 21DQ09N-FC4 1N4937 1SS133T-77 MTZJ18B T-77 31DF6-FC 1N4937 SB290S MTZJ5.6B T-77 SB290S MTZJ15B T-77 1SS133T-77 1SS133T-77 1SS133T-77 1SS133T-77 MTZJ18B T-77 1SS133T-77 MTZJ8.2B T-77 1N4005-EIC MTZJ5.6B T-77 1N4005-EIC 1N4005-EIC 1N4005-EIC MTZJ6.2B T-77 MTZJ6.2B T-77 MTZJ6.2B T-77 11E1-EIC MTZJ5.6B T-77 1SS133T-77 1SS133T-77 1SS133T-77 1SS133T-77 1SS133T-77 1SS133T-77 MTZJ6.2B T-77 1SS133T-77 1SS133T-77 1SS133T-77 1SS133T-77 1SS133T-77 1SS133T-77 OEC7074A PST600C S-24C16AFJA-TB-01 TB1253N M62420SP LA78041 KIA7809API KIA7805API LTV-817M-VB MM1311AD AN5829S AN5276 LA76600M-TLM 2SC2412KT146 R,S 2SC2412KT146 R,S KRC102SRTK 2SC2412KT146 R,S 2SC2412KT146 R,S 2SC2412KT146 R,S 2SA1037AKT146R,S KTC3881S-RTK KTC3227_Y-AT 2SD2499(LB0EC1) DTA144EKAT146 KRC111SRTK KTC3203_Y-AT 2SK3326(2) 2SA1371(D,E)-AE KTC3198-AT(Y,GR) 2SC2909(S,T)-AA
! ! ! ! ! ! ! ! ! ! !
! ! ! ! ! !
ICS
IC IC IC IC IC IC IC IC PHOTO COUPLER IC IC IC IC TRANSISTOR,SILICON TRANSISTOR,SILICON COMPOUND TRANSISTOR TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON COMPOUND TRANSISTOR COMPOUND TRANSISTOR TRANSISTOR,SILICON FET TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON
! ! ! !
TRANSISTORS
! !
! ! ! !
Description
2SA1037AKT146R,S KTC3198-AT(Y,GR) KTA1273_Y KRC102SRTK 2SD734(E,F)-AA 2SA1624-AA KTC3203_Y-AT KRA102SRTK 2SC2412KT146 R,S 2SC2412KT146 R,S 2SC2412KT146 R,S 2SC2412KT146 R,S 2SC2412KT146 R,S 2SA1037AKT146R,S KTC4217(O,Y) 2SC2621(D,E)-RAC KTC4217(O,Y) 2SC2621(D,E)-RAC KTC4217(O,Y) 2SC2621(D,E)-RAC KTC3199_Y-AT 2SC1740SP TP KTC3199_Y-AT 2SC1740SP TP KTC3199_Y-AT 2SC1740SP TP KRC111SRTK 2SC2412KT146 R,S 2SC2412KT146 R,S 2SC2412KT146 R,S 2SA1037AKT146R,S 2SC2412KT146 R,S 2SC2412KT146 R,S 100 UH 100 UH 1.2 UH 15 UH 47 UH 47 UH 47 UH 22 UH ELH5L4113 2R2A752F28Y 8R270008 47 UH 47 UH 100 UH 47 UH 47 UH 100 UH 150 UH 150 UH 150 UH 22 UH 220 UH 220 UH 220 UH 220 UH 15 UH 100 UH 15 UH 15 UH 22 UH ETH14Y47AY 8140065S MSP-213V2-432 PBSN YKF51-5503 MSP-213V2-432 PBSN MSP-213V1-652 PBSN AV1-06D-3 AV1-06D-4 AV1-06DS-2 MSP-213V2-432 PBSN ISHS53S
TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON COMPOUND TRANSISTOR TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON COMPOUND TRANSISTOR TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON COMPOUND TRANSISTOR TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON COIL COIL COIL COIL COIL COIL COIL COIL COIL,LINEARITY COIL,LINE FILTER COIL,DEGAUSS COIL COIL COIL COIL COIL COIL COIL COIL COIL COIL COIL COIL COIL COIL COIL COIL COIL COIL COIL TRANS,HORIZONTAL DRIVE TRANSFORMER,SWITCHING
or or or or or or
COILS &TRANSFORMERS
or
or
or or
JACKS
RCA JACK JACK RCA JACK RCA JACK RCA JACK RCA JACK RCA JACK RCA JACK SOCKET,CATHODE RAY,TUBE
Description
SKHVBED010 SKHVBED010 SKHVBED010 SKHVBED010 SKHVBED010 NVG6TLTAB222 EVNCYAA03BE4 TMA530A TCA389A TEAA92A BL02RN1-R62T2 BL02RN1-R62T2 W4BRH3.5X6X1 0R615901 CU252002 CU2A3601 CU822501 CU822501 EFCT4R5YS5A TSF5229P3 TPSRA4M50C00-A0 TKC-M07X-A1 A2361WV2-4P TS-80P-04-V1 A3963WV2-3PD A1561WV2-2P A2361WV2-2P 005P-2100 A2001WV2-10P A2361WV2-2P CH243001 A2502WV2-4P A2001WV2-5P B2013H02-5P B2013H02-10P XRY20X30BD XRY16X28BD 51MS063L 3227009R EYF-52BC EYF-52BC RPM7138-H5 ALKS321 S0509F12-C ZPB45BL3R0A SBKMOP006B ENV56DB6G3 A68AJB82X10 EFOEC8004T4 HC-49/C
VARIABLE RESISTORS
VOLUME,SEMI FIXED VOLUME,SEMI FIXED PCB ASS'Y PCB ASS'Y PCB ASS'Y CORE,BEADS CORE,BEADS CORE,BEADS CORD,AC BUSH CORD,CONNECTOR CORD,CONNECTOR CORD,CONNECTOR CORD,CONNECTOR FILTER,CERAMIC FILTER,SAW FILTER,CERAMIC TRAP CONNECTOR PCB SIDE CONNECTOR PCB SIDE CONNECTOR PCB SIDE CONNECTOR PCB SIDE CONNECTOR PCB SIDE CONNECTOR PCB SIDE CONNECTOR PCB SIDE CONNECTOR PCB SIDE CONNECTOR PCB SIDE CORD,CONNECTOR CONNECTOR PCB SIDE CONNECTOR PCB SIDE WIRE HOLDER WIRE HOLDER CUSHION A EYE LET EYE LET FUSE TRANSFORMER,FLYBACK HOLDER,FUSE HOLDER,FUSE REMOTE RECEIVER RELAY SPEAKER DEGAUSS ELEMENT TRANSMITTER TUNER,VHF-UHF CRT W/DY CERAMIC,OSCILLATOR CRYSTAL
P.C.BOARD ASSEMBLIES
MISCELLANEOUS
or
TOSHIBA CORPORATION
1-1, SHIBAURA 1-CHOME, MINATO-KU, TOKYO 105-8001, JAPAN