Beruflich Dokumente
Kultur Dokumente
http://technet.microsoft.com/en-us/library/bb727...
This white paper explains how to get replication to function properly in environments where an Active Directory directory forest is distributed among internal perimeter networks (also known as DMZ, demilitarized zones, and screened subnets) and external (Internet-facing) networks.
On This Page
Introduction Full Dynamic RPC How RPC Works Limited RPC Encapsulating Inside IPSec Domain Controller Promotion with PPTP Tunnels Domain Controller Promotion with IPSec and Machine Certificates Comparison of the Two Methods of Promotion Configuring IPSec Transport Mode for DC-to-DC Communication Further Lockdown of DCs in a Perimeter Network Is This a Legitimate Use of IPSec?
Introduction
Firewalls present two difficulties when deploying a distributed Active Directory (AD) directory service architecture: Initially promoting a server to a domain controller. Replicating traffic between domain controllers. Active Directory relies on remote procedure call (RPC) for replication between domain controllers. (Simple Mail Transfer Protocol [SMTP] can be used in certain situationsschema, configuration, and global catalog replication, but not domain naming contextlimiting its usefulness.) Getting replication to function properly in environments where a directory forest is distributed among internal, perimeter networks and external (that is, Internet-facing) networks can be challenging. There are three possible approaches: Open the firewall wide to permit RPC's native dynamic behavior. Limit RPC's use of TCP ports and open the firewall just a little bit. Encapsulate domain controller (DC-to-DC) traffic inside IP Security Protocol (IPSec) and open the firewall for that.
1 of 19
06/30/2011 07:57 AM
http://technet.microsoft.com/en-us/library/bb727...
Each approach has its pros and cons. In general, there are more cons than pros at the top of the list, and more pros than cons at the bottom. So although this document describes how to do all three, most of its focus is on the IPSec approach because of its benefits over the other two. Top of page
No special server configuration Turns the firewall into "Swiss cheese" Random incoming high-port connections Insecure firewall configuration Although configuring your environment to work this way is certainly possible, there are plenty of reasons not to do itmost importantlyit results in an insecure network. It does, however, require the least amount of configuration work. To enable replication over dynamic RPC, configure your firewall to permit the following. Service RPC endpoint mapper Network basic input/output system (NetBIOS) name service NetBIOS datagram service NetBIOS session service RPC dynamic assignment Server message block (SMB) over IP (Microsoft-DS) Lightweight Directory Access Protocol (LDAP) LDAP ping Port/protocol 135/tcp, 135/udp 137/tcp, 137/udp 138/udp 139/tcp 1024-65535/tcp 445/tcp, 445/udp 389/tcp 389/udp
2 of 19
06/30/2011 07:57 AM
http://technet.microsoft.com/en-us/library/bb727...
LDAP over SSL Global catalog LDAP Global catalog LDAP over SSL Kerberos
Windows Internet Naming Service (WINS) resolution (if required) 1512/tcp, 1512/udp WINS replication (if required) 42/tcp, 42/udp
1 TCP is used for zone transfers and whenever answers to questions exceed 512 bytes. It is that "RPC dynamic assignment" rule that makes this scenario insecure. Sometimes referred to as "TCP high ports," the rule needs to permit inbound traffic on any port above 1023. If your firewall permits this, there is very little reason even to have a firewall. If you do not want to permit DNS or WINS, you can use HOSTS (for DNS) and LMHOSTS (for WINS) files for name resolution. These files are stored in %SystemRoot%\system32 \drivers\etc. Look inside the files for information on how to use them. Top of page
3 of 19
06/30/2011 07:57 AM
http://technet.microsoft.com/en-us/library/bb727...
Limited RPC
Pros Cons
More secure than dynamic RPConly one open high port Registry modification to all servers This scenario gives you more security, but it does require making registry modifications to all your domain controllers. Registry modifications can be scripted with tools in the Microsoft Windows 2000 Resource Kit, which helps eliminate configuration errors. You must decide upon fixed port numbers for AD replication for the file replication service (FRS). The Internet Assigned Numbers Authority (IANA) has set aside the range 49152 through 65535 for use by private and dynamic assignments. Using the registry editor, navigate to this registry key: HKEY_LOCAL_MACHINE SYSTEM\ CurrentControlSet\ Services\ NTDS\ Parameters\ Add a new DWORD value called TCP/IP Port (include the space). Set the value's data to the port number that you want to use (remember to change the displayed base to decimal before you enter the data). Next, navigate to this registry key: HKEY_LOCAL_MACHINE SYSTEM\ CurrentControlSet\ Services\ NTFRS\ Parameters\ Add a new DWORD value called RPC TCP/IP Port Assignment (include the spaces). Set the value's data to the port number that you want to use (remember to change the displayed base to decimal before you enter the data). Do this on all your Active Directory servers. You must restart them for the change to take effect. Now configure your firewall to permit the following. Service Port/protocol
4 of 19
06/30/2011 07:57 AM
http://technet.microsoft.com/en-us/library/bb727...
RPC endpoint mapper NetBIOS name service NetBIOS datagram service NetBIOS session service
RPC static port for AD replication <AD-fixed-port>/TCP RPC static port for FRS SMB over IP (Microsoft-DS) LDAP LDAP ping LDAP over SSL Global catalog LDAP Global catalog LDAP over SSL Kerberos DNS WINS resolution (if required) WINS replication (if required) <FRS-fixed-port>/TCP 445/tcp, 445/udp 389/tcp 389/udp 636/tcp 3268/tcp 3269/tcp 88/tcp, 88/udp 53/tcp, 53/udp 1512/tcp, 1512/udp 42/tcp, 42/udp
Replace <AD-fixed-port> and <FRS-fixed-port> with the port numbers that you used in the registry values. As before, if you do not want to permit DNS or WINS, you can use HOSTS (for DNS) and LMHOSTS (for WINS) files for name resolution. These files are stored in
5 of 19
06/30/2011 07:57 AM
http://technet.microsoft.com/en-us/library/bb727...
%SystemRoot%\system32\drivers\etc. Look inside the files for information on how to use them. You still need the endpoint mapper because clients will not know that you fixed the ports. The endpoint mapper always returns your fixed ports when clients request the port numbers associated with AD's and FRS's RPC UUIDs. Here is some text that you can import into the registry. It sets the AD port to 49152 and the FRS port to 49153. Copy it to the clipboard, paste it into a blank Notepad screen, save the file with a .REG extension, and then double-click that file in Windows Explorer. If you want to use a different port, use the Windows Calculator (in scientific mode) to convert the number from decimal to hexadecimal. Remember to pad the value with four leading zeros, as you see in the following example.
Windows Registry Editor Version 5.00 [HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\NTDS\Parameters] "TCP/IP Port"=dword:0000c000 [HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\NTFRS\Parameters] "RPC TCP/IP Port Assignment"=dword:0000c001
Top of page
Mutual authentication between DCs Individualized policies, if required Good reason to start deploying a public key infrastructure (PKI), if desired IPSec provides a way to easily encapsulate and carry RPC traffic over a firewall. Besides simplifying the transport of RPC, IPSec also increases security between the DCs because of IPSec's mutual authentication feature: by using either Kerberos or machine certificates, the DCs will "know" whom they are communicating with before any actual information exchange occurs. This document shows you how to create an appropriate IPSec policy by using the Microsoft Management Console (MMC) interface. You can script policy creation with IPSECPOL.EXE, a tool available in the Windows 2000 Resource Kit. Be sure to thoroughly read and understand the IPSECPOL.EXE documentation before you try to use itunlike the GUI, the command-line tool has very little consistency checking built in.
6 of 19
06/30/2011 07:57 AM
http://technet.microsoft.com/en-us/library/bb727...
There is one decision that you must make before you beginwhether to use certificates for IPSec authentication or built-in Kerberos for Windows 2000. Kerberos authentication requires that both computers already be in the same domain, so if you prefer Kerberos, then you must use something other than IPSec for the domain controller promotion (DCPROMO) phase (because the target server is not yet a member of the domain). Point-to-Point Tunneling Protocol (PPTP) tunnels work well for this and are documented here. If instead you want to use certificates for authentication, you must obtain a certificate for each DC that will participate in IPSec replication. Please see http://www.microsoft.com/windows2000/library/ for documents that describe how to build a Windows 2000 certificate authority and how to configure your domain for automatic enrollment of machine certificates. For IPSec replication and IPSec or PPTP promotion, configure your firewall to permit the following. Service DNS PPTP establishment (if using PPTP) Port/protocol 53/tcp, 53/udp 1723/tcp
2
GRE, generic routing encapsulation (if using PPTP) IP protocol 47 Kerberos IKE, Internet Key Exchange IPSec ESP, encapsulated security payload IPSec AH, authenticated header 88/tcp, 88/udp 500/udp IP protocol 50 IP protocol 51
If you decide to use certificates for IPSec authentication instead of Kerberos, you can configure 1 the servers to carry Kerberos traffic inside IPSec. This will be covered in more detail later. Regardless of authentication mode, Kerberos between domain controllers is still required. Note that IPSec will not work through network address translation (NAT) devices. Because IPSec uses IP addresses when computing packet checksums, IPSec packets whose source addresses were altered by NAT are discarded when they arrive at the destination. Top of page
7 of 19
06/30/2011 07:57 AM
http://technet.microsoft.com/en-us/library/bb727...
controller or on a separate server. For simplicity, it is best that the RRAS server exist in the same subnet as the root domain controllerthen no static route maintenance is necessary. To configure RRAS: Select Start | Programs | Administrative Tools | Routing and Remote Access. Right-click your server in the left-hand pane, and then click Configure and Enable Routing and Remote Access. The RRAS setup wizard starts. Click Manually configured server.
Figure 1: Routing and Remote Access Wizard Finish the wizard and start the service when it prompts you. The MMC should now look like this, after clicking on the + next to the server name.
Figure 2: RRAS after Configuring and Enabling After RRAS is configured and enabled, make the following changes: Right-click the server, and then click Properties. Click the IP tab. Click Static address pool. Type an IP address range in the same subnet as your internal domain controller. Only a
8 of 19
06/30/2011 07:57 AM
http://technet.microsoft.com/en-us/library/bb727...
Figure 3: Server Properties, IP Address Assignment Right-click Ports (in the left pane of the MMC), and then click Properties. Configure Direct parallel so that neither remote access nor demand dial connections are permitted; if you have any modems on the server (as in the example below), configure them likewise. Configure Demand dial (L2TP) so that there are zero ports and neither remote access nor demand dial connections are permitted. You do not need to make any changes to Demand dial (PPTP) unless you need more than five ports. Close all dialog boxes.
9 of 19
06/30/2011 07:57 AM
http://technet.microsoft.com/en-us/library/bb727...
Figure 4: Ports Properties RRAS is now ready to accept inbound PPTP connections for domain controller promotion. Before promoting a perimeter network or external server to a domain controller, establish a PPTP tunnel to the internal RRAS server. Open the Properties page of My Network Places and click Make New Connection. In the wizard: Click Connect to a private network through the Internet. Do not dial any initial connection. Type the IP address of the internal RRAS server as the destination. Set the connection availability to For all users. Do not share the connection. Name the connection whatever you wish. The connectoid then opens. Before connecting, click the Properties button. Click the Options tab, and then click Include Windows logon domain. Close the dialog box. Now log onto the RRAS server by using enterprise administrator credentials (the administrator of the root domain). After the server completes the connection, you may start DCPROMO. DCPROMO requires a reboot at the end of the process; this will also disconnect the PPTP tunnel. Because you no longer need the tunnel, you may delete the connectoid. Top of page
10 of 19
06/30/2011 07:57 AM
http://technet.microsoft.com/en-us/library/bb727...
11 of 19
06/30/2011 07:57 AM
http://technet.microsoft.com/en-us/library/bb727...
Including Kerberos inside IPSec is fine after a machine is promoted to a domain controller (and thus is a member of the domain). But for a machine not yet a member of a domainthe one that you want to promote to a domain controlleryou cannot establish IPSec by using Kerberos. You must use some other form of authentication, which is the reason for using machine certificates. Here is some text that you can import into the registry. It will set the NoDefaultExempt value to 1. Copy it to the clipboard, paste it into a blank Notepad screen, save the file with a .REG extension, and then double-click that file in Windows Explorer.
Windows Registry Editor Version 5.00 [HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\IPSEC] "NoDefaultExempt"=dword:00000001
Understand this before you proceed. If you decide to follow this approach, you also must follow all the steps in the next section, "Configuring IPSec transport mode for DC-to-DC communication," before you run DCPROMO. Here is the order: 1. If you want to include Kerberos in IPSec processing, add the previous registry key. 2. Install a certificate authority. 3. Obtain machine certificates for all existing domain controllers and for all candidate domain controllers. 4. Perform the steps in the section "Configuring IPSec transport mode for DC-to-DC communication." 5. Run DCPROMO on candidate domain controllers. 6. All doneleave everything in place; ongoing replication occurs over the existing IPSec configuration. Top of page
12 of 19
06/30/2011 07:57 AM
http://technet.microsoft.com/en-us/library/bb727...
Allows Kerberos to be included in IPSec processing. Fewer protocols through the firewallno PPTP, possibly no Kerberos. Single step for promotion and ongoing replication. Although neither method is preferred over the other, using IPSec with machine certificates is probably the more "forward looking" approach, especially because most organizations plan to deploy PKIs of some kind. Top of page
Figure 5: Local Security Settings Next, click IP Security Policies on Local Machine (in the left-hand pane of the MMC). This displays the default policies, where you will add a new one for replication. First, however, you must create the filter list and action. The filter list indicates which IP addresses, ports, and protocols trigger the application of IPSec. You want to secure all the traffic between the domain controllers only, not any traffic between a domain controller and some other machine. Right-click in the MMC's right-hand pane and click Manage IP filter lists and filter actions. You will be on the Manage IP Filter Lists tab. A filter list is simply a list of filters; you will create a filter for each server that this one replicates with. That is, only one filter list is required and the list contains filters for all domain controllers.
13 of 19
06/30/2011 07:57 AM
http://technet.microsoft.com/en-us/library/bb727...
Figure 6: IP Filter Lists and Filter Actions, Filter Lists Tab Click the Add button to create a new filter list. Name the filter list DC replication. Click the Add button to create a new filter; follow these steps to complete the wizard: Select My IP address as the source address. Select A specific IP address as the destination address, and then type the IP address of the other server. Select Any as the protocol type. This configures the filter so that all traffic between the two 2 computers will be carried inside IPSec .
Figure 7: Domain Controller Replication Filter List Add additional filters for the remaining domain controllers. When finished, close the dialog box. Next, you want to define a filter action. Click the Manage filter actions tab, and then click the
14 of 19
06/30/2011 07:57 AM
http://technet.microsoft.com/en-us/library/bb727...
Click Do not communicate with computers that do not support IPSec. Click High (Encapsulated Secure Payload). Select the Edit properties check box (you will need to make changes later). Click the Finish button. In the Properties dialog box, clear the check box next to Accept unsecured communication, but always respond using IPSec. You do not want the server to respond at all to unsecured communication. Of course, this applies only to those machines that are part of the corresponding IP filter list; you will link the filter list and the filter action with a policy in just a moment. Close all dialog boxes.
10
Figure 8: Domain Controller Replication Filter Action Now you are ready to create the IPSec policy. Right-click in the MMC's right-hand pane and click Create IP security policy. In the wizard: Name the policy Domain controller replication. Clear Activate the default response rule. Ensure that the Edit properties check box is selected and close the wizard.
15 of 19
06/30/2011 07:57 AM
http://technet.microsoft.com/en-us/library/bb727...
11
Figure 9: Domain Controller Replication IPSec Policy You create a rule by associating the filter list and filter action that you created earlier. Click the Add button to define a new rule. In the wizard: Select This rule does not specify a tunnel. Select Local area network (LAN) for the network type. Choose an authentication method Select Windows 2000 default (Kerberos V5 protocol) if you used PPTP tunnels for DCPROMO, or Select Use a certificate from this Certificate Authority (CA) if you are using certificates. Then click Browse and select the certificate authority that issued the machine certificate installed on the computer. You will see a list of IP filter lists. Select the filter list that you created earlier, DC replication, from the list. You will see a list of filter actions. Select the filter action that you created earlier, DC replication, from the list. Do not edit the properties. Finish the wizard. Your policy will now look like this (the authentication column will indicate "Certificate" if you
16 of 19
06/30/2011 07:57 AM
http://technet.microsoft.com/en-us/library/bb727...
12
Figure 10: Completed Domain Controller Replication Policy Finally, you need to turn onthat is, assignthe policy. Right-click the Domain controller replication policy. Click Assign.
13
Figure 11: Domain Controller Policy Is Assigned IPSec processing happens immediately. There is no need to reboot the server. Every domain controller requires a similar IPSec policy. Regardless of whether the controller is in the internal network, the perimeter network, or the external network, you must configure its IPSec policy so that all communications with all other domain controllers are through IPSec. Not only does this allow the knowledge consistency checker to build a replication topology that ignores the firewall, it also secures all IPSec replication between every server. Testing the IPSec policy. Be sure to test the policies that you have created. After you have created and assigned a policy on at least two machines, you can use the IPSECMON.EXE utility to
17 of 19
06/30/2011 07:57 AM
http://technet.microsoft.com/en-us/library/bb727...
observe when the machines establish the IPSec security association: Open a command window. Issue the command ipsecmon. A graphical utility starts, listing current security associations and how much authenticated and/or encrypted traffic has passed through the server. (Unless the DCs have started to exchange information, there probably will not be any system administrators right now.) Click the Options button and change the refresh rate to one second. Go back to the command prompt and ping another domain controller that also has an IPSec policy. Use the -t flag to ping continuously until stopped (ping -t ip-address ). Look for several "Negotiating IP security" responsesthe machines are exchanging cryptographic keys and building their security associations. Finally you will see normal replies. It may take 10 to 12 seconds to establish the security associations in both directions. Press CTRL +C to stop. Top of page
For more information about Windows 2000 IPSec, and other security features of Windows 2000, please begin your adventure at http://www.microsoft.com/technet/security/default.mspx . Top of page
15
18 of 19
06/30/2011 07:57 AM
http://technet.microsoft.com/en-us/library/bb727...
This document doesn't discuss using preshared keys. Preshared key authentication is included in Windows 2000 only for compatibility with other IPSec implementations and to conform to the 1 IPSec RFCs. In no cases do we encourage the use of preshared keys in a production environment because of the inherent security risks associated with shared-secret style authentication. 2 That is, all traffic except that which is exempted from IPSec processing, as discussed earlier.
Links Table
1 2 3 4 5 6 7 8 9
http://blogs.technet.com/steriley http://www.microsoft.com/windows2000/library/ http://technet.microsoft.com/en-us/library/Bb727063.adrep01_big(l=en-us).gif http://technet.microsoft.com/en-us/library/Bb727063.adrep02_big(l=en-us).gif http://technet.microsoft.com/en-us/library/Bb727063.adrep03_big(l=en-us).gif http://technet.microsoft.com/en-us/library/Bb727063.adrep04_big(l=en-us).gif http://technet.microsoft.com/en-us/library/Bb727063.adrep05_big(l=en-us).gif http://technet.microsoft.com/en-us/library/Bb727063.adrep06_big(l=en-us).gif http://technet.microsoft.com/en-us/library/Bb727063.adrep07_big(l=en-us).gif http://technet.microsoft.com/en-us/library/Bb727063.adrep08_big(l=en-us).gif http://technet.microsoft.com/en-us/library/Bb727063.adrep09_big(l=en-us).gif http://technet.microsoft.com/en-us/library/Bb727063.adrep10_big(l=en-us).gif http://technet.microsoft.com/en-us/library/Bb727063.adrep11_big(l=en-us).gif http://www.microsoft.com/technet/itsolutions/network/security/ipsecld.mspx http://www.microsoft.com/technet/security/default.mspx
10 11 12 13 14 15
19 of 19
06/30/2011 07:57 AM