Sie sind auf Seite 1von 32

Installation

Details

Note:

The following 'Design Details' have been produced to assist architects and designers in the use of Architectural Window Systems (AWS) commercial products and accessories. All care has been taken in the production of these pages, but Architectural Window Systems Pty Ltd can take no responsibility for errors. If you should find any errors please contact your local AWS sales office. Details are subject to change without notice. The latest information can be accessed on our web site www. awscommercial.com.au

INDEX INSTALLATION
DATE MAR 08 REPLACES MAR 07 SCALE

Page 110. 110. 110. 110. 110. 110. 110. 110. 110. 110. 110. 110. 110. 110. 110. 110. 110. 110. 110. 110. 110. 110. 110. 110. 110. 110. 110. 110. 110. 110. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30

Contents Installation Details. Shopfront Framing typical shopfront framing installation. Nailing fin adaptors. 410 Bi-fold door without sub-sill. 410 Bi-fold door with sub-sill. 411 Bi-fold door - Head. 411 Bi-fold door - Head. 411 Bi-fold door - Sill alternatives. 411 Bi-fold door - Sill alternatives. 411 Bi-fold door - Flydoor vertical section. 411 Bi-fold door - Flydoor alternative sills. 411 Bi-fold door - Flydoor horizontal section. 411 Bi-fold door - Flydoor horizontal section. 102mm sub-sill. 102mm sub-sill. Nailing fin sub-sill. Nailing fin sub-sill. 102mm sub-head and two piece sub-jamb. 150mm sub-sill. 102mm sub-sill 150mm sub-sill. 150mm sub-head and two piece sub-jamb. Building-in lugs. Windows snap couplers. Windows snap couplers. Nailing fin frame external closer. Nailing fin frame external closer. Internal perimeter trims. Internal perimeter trims. Flydoor adaptor.

110.0

AWS COMMERCIAL ARCHITECTURAL INFORMATION DETAILS SUBJECT TO CHANGE WITHOUT NOTICE

Installation Details ACCESSORIES


DATE MAR 04 REPLACES SCALE NOT TO SCALE

Recommended installation instructions for aluminium windows


The following pages show a number of typical window, door and framing building-in details and coupling arrangements, if the information you require is not covered in these pages contact your local AWS fabricator or email Architectural Window Systems direct at: info@awscommercial.com.au Fix the frames to structure with building-in lugs fasteners and shims as indicated. Installation of windows to be in accordance with Australian Standard AS 2047. Suggested installation steps: 1. 2. If flashing is required fit the flashing to jambs and/or sill as specified. Fit shims on sill plate / slab on meeting stile or mullion centre line and at 450mm maximum centres. Make sure these shims are level. Install the frame into the opening. Fit shims on jambs making sure that the frame is plumb and square, measure frame across diagonals to check for square. Fix the frame to structure by nailing through timber reveals. Make sure that the frame is not twisted. Alternative - On solid brick construction fit buildingin lugs at 450mm maximum centres. Take care that head, sill and/or jamb are not dished or bowed during installation. Make sure the sill reveal is fully supported, if necessary use additional shims. Failure to do so may result in problems with sash operation. Cement mortar or render droppings can permanently damage aluminium. Remove them as soon as possible. Leave at least 10mm gap between sill brick and frame to allow for possible future building settlement. Install Panels into Frame
Check measure diagonals during installation Building-in lugs at approx. 450mm maximum centres Locate one lug at lock keeper position It's critical that sill is installed level. Use spirit level on straight edge Shim sill as required to obtain level at 300mm approx. centres Double fix at transoms

Double-hung Window
Check measure diagonals during installation Building-in lugs at approx. 450mm maximum centres On double-hung windows ensure jambs are plumb and straight.

3. 4.

Transom windows

5.

Double fix at transoms

6. 7.

8. 9.

10. On brick veneer construction there should be at least a 12mm gap between timber header and aluminium frame. 11. Aluminium windows and frames are not designed to support eaves linings.

Important Note: If you install windows out of square or without sufficient shims the opening sashes won't perform satisfactorily.

For the latest accessories refer our web site:

www.awscommercial.com.au

AWS COMMERCIAL ARCHITECTURAL INFORMATION DETAILS SUBJECT TO CHANGE WITHOUT NOTICE

110.1

TYPICAL SHOPFRONT FRAMING INSTALLATION ACCESSORIES


DATE MAR 04 REPLACES SCALE HALF FULL SIZE

Concrete slab/beam over. Cement render. 33 Continuous caulking. Extruded aluminium subhead Fixings @ 450mm maximum centres. Frame size Co-extruded Santoprene bulb seal. Typical shopfront frame. Roll-in wedge. Apply continuous run of caulking before fitting wedge. Extruded aluminium sub-sill. Floor finish

20

Frame size

Note: It is recommended that the installer apply coat of waterproof membrane to concrete rebate before fitting sub-sill and caulking. Basically untreated concrete is not necessarily waterproof.

Continuous caulking. 115 Shim sub-sill level and fix to slab @ 450mm max. cts. Fix jamb to slab @ 450mm m a x i m u m c e n t re s . F i t 150mm lengths of filler and shim before driving screws home. Use aluminium angle trims, depending on the wall finishes.

CAD file: DWG or DXF AWS_Install_1

3 min.

Frame size

Alternative jamb fixing using custom extruded aluminium fixing lug, lugs 75mm wide and fixed @ 450mm max. cts.

Cement render

For the latest accessories refer our web site:

www.awscommercial.com.au

110.2

AWS COMMERCIAL ARCHITECTURAL INFORMATION DETAILS SUBJECT TO CHANGE WITHOUT NOTICE

20

Drainage holes at 400mm cts.

NAILING FIN ADAPTORS ACCESSORIES


DATE MAR 07 REPLACES MAR 04 SCALE HALF FULL SIZE

102mm Nailing fin adaptor

Suits any of the 102mm frames including: Series 400 CentreGLAZE Series 406 FrontGLAZE Series 426 FrontGLAZE Series 407 FACELINE Series 702 SlideMASTER Series 704 SlideMASTER Series 410 FoldMASTER Series 411 ViewMASTER

The location of the nailing fin aligns with the dedicated nailing fin frames on Series 400, 452, 453, 462, 463, 464, 466 and 467 frames.

CAD file: DWG or DXF AWS_Install_2

80mm Nailing fin adaptor

We have an 80mm nailing fin adaptor for the Series 80 offset narrow frame.

For the latest accessories refer our web site:

www.awscommercial.com.au

AWS COMMERCIAL ARCHITECTURAL INFORMATION DETAILS SUBJECT TO CHANGE WITHOUT NOTICE

110.3

410 BI-FOLD DOOR WITHOUT SUB-SILL ACCESSORIES


DATE MAR 07 REPLACES MAR 04 SCALE HALF FULL SIZE

Slab/beam over Cement render Aluminium angle trim. Fix head to slab @ 450mm max. cts. Make sure head is shimmed correctly. 6

Important Note: As bi-fold doors open out make sure there are no external obstructions.

Flat cover fitted after the head fixings.

Frame size

Flat cover fitted after the sill fixings. Fix to slab @ 450mm max. cts. Shim under sill making sure frame is square and level. CAD file: DWG or DXF AWS_Install_1 Continuous caulking.

Sill drainage holes drain water into tubular sump then out on the front face. 120 110

For the latest accessories refer our web site:

www.awscommercial.com.au

110.4

AWS COMMERCIAL ARCHITECTURAL INFORMATION DETAILS SUBJECT TO CHANGE WITHOUT NOTICE

By recessing the floor slab (including the floor finish) 69mm you can get a flush finish as detailed

410 BI-FOLD DOOR WITHOUT SUB-SILL ACCESSORIES


DATE MAR 07 REPLACES MAR 04 SCALE HALF FULL SIZE

Bricks Cement render Fix head to lintel @ 400mm max. cts. Make sure head is shimmed correctly.

Important Note: As bi-fold doors open out make sure there are no external obstructions.

Flat cover fitted after the head fixings.

Frame size

Flat cover fitted after the sill fixings. Fix to sub-sill adaptor with 10# s.s. self tapping screws. Fix to sub-sill to slab and shim to making sure frame is square and level. Continuous caulking.

CAD file: DWG or DXF AWS_Install_1

Face of brick wall over 120 115

For the latest accessories refer our web site:

www.awscommercial.com.au

AWS COMMERCIAL ARCHITECTURAL INFORMATION DETAILS SUBJECT TO CHANGE WITHOUT NOTICE

By recessing the floor slab (including the floor finish) 82mm you can get a flush finish as detailed

20

110.5

411 BI-FOLD DOOR - HEAD ACCESSORIES


DATE MAR 07 REPLACES NOV 04 SCALE HALF FULL SIZE

Typical cavity brick head detail.

Seal head to lintels inside and out. M8 Bolts secure head to lintel @ 600mm max. cts. with additional bolts to support panels in the folded open position. One bolt per panel @ 100mm cts., refer typical layout example below. It's important to take care when packing the head and make sure the head remains square after tightening the fixings.

scale: half full size

Head fixing locations: A = 150mm approximately B = 100mm approximately C = 600mm maximum

A BB B

B A

For the latest accessories refer our web site:

www.awscommercial.com.au

110.6

AWS COMMERCIAL ARCHITECTURAL INFORMATION DETAILS SUBJECT TO CHANGE WITHOUT NOTICE

411 BI-FOLD DOOR - HEAD ACCESSORIES


DATE MAR 07 REPLACES NOV 04 SCALE HALF FULL SIZE

Typical brick veneer head detail.


Important Note: Head fixed to steel beam.

M8 Bolts secure head to 'C' beam @ 600mm max. cts. with additional bolts to support panels in the folded open position. One bolt per panel @ 100mm cts., refer typical layout example below. It's important to take care when packing the head and make sure the head re m a i n s s q u a re a f t e r tightening the fixings.

scale: half full size

Head fixing locations: A = 150mm approximately B = 100mm approximately C = 600mm maximum

A BB B

B A

For the latest accessories refer our web site:

www.awscommercial.com.au

AWS COMMERCIAL ARCHITECTURAL INFORMATION DETAILS SUBJECT TO CHANGE WITHOUT NOTICE

110.7

411 BI-FOLD DOOR - SILL ALTERNATIVES ACCESSORIES


DATE MAR 07 REPLACES NOV 04 SCALE HALF FULL SIZE

Water Resistance: Recessed sill shown on this page has no water resistance.

This recessed sill can be fabricated and shipped with the main frame. Cut 120mm x 35mm recess in floor finish to accept this sill.

35

120

81502

Water Resistance: Ramp sill shown on this page has no water resistance.

Raised ramp floor guide. Ramp screwed to floor with stainless steel screws in plugs.

34

81626 All AWS sills cater for 5mm plus and minus adjustment to cater for building settlement.

For the latest accessories refer our web site:

www.awscommercial.com.au

110.8

AWS COMMERCIAL ARCHITECTURAL INFORMATION DETAILS SUBJECT TO CHANGE WITHOUT NOTICE

35

81628

25

411 BI-FOLD DOOR - SILL ALTERNATIVES ACCESSORIES


DATE MAR 07 REPLACES NOV 04 SCALE HALF FULL SIZE

Water Resistance: Weather resisting sill shown left has been tested to resist 200Pa water.

Weatherpile fin seal 97023. Weather resisting sill detail.

81625

8mm dia. Drainage holes @ 600mm max. cts. Fit nylon grommets 94421 onto visible front holes.

35

81542

Weatherpile fin seal 97023. Weather resisting sill detail.

27

35

81625

20

80518

8mm Drainage holes @ 600mm max. cts. 20 x 6 sub-sill drainage slots @ 400mm max. cts. Co-extruded Santoprene cover flap 94055P.

112

40

Water Resistance: Fitting sub-sill under external opening bi-fold doors will increase the water resistance to 300Pa.

scale: half full size

For the latest accessories refer our web site:

www.awscommercial.com.au

AWS COMMERCIAL ARCHITECTURAL INFORMATION DETAILS SUBJECT TO CHANGE WITHOUT NOTICE

110.9

411 BI-FOLD DOOR - VERTICAL ACCESSORIES


DATE MAR 08 REPLACES MAR 07 SCALE HALF FULL SIZE

Flyscreen Frame Height = H + 8

H = O/A Height

M8 Bolts secure head to lintel @ 600mm max. cts. with additional bolts to support panels in the folded open position. One bolt per panel @ 100mm cts., refer typical layout example below. It's important to take care when packing the head and make sure the head remains square after tightening the fixings. Seal head to lintels on the outside.

If you want to tuck the internal wall lining into flydoor head as drawn take care when positioning the framing in the wall. Maximum screen frame height 3000mm.

Shim and fix flyscreen sill to floor @ 600mm max. cts. Recess the sill into the floor slab as drawn.

10mm Shims under Bi-fold sill.

4mm Shims under flyscreen sill.

For the latest accessories refer our web site:

211 www.awscommercial.com.au

110.10

AWS COMMERCIAL ARCHITECTURAL INFORMATION DETAILS SUBJECT TO CHANGE WITHOUT NOTICE

39

20

411 BI-FOLD DOOR - ALTERNATIVE SILLS ACCESSORIES


DATE MAR 08 REPLACES MAR 07 SCALE HALF FULL SIZE Fitting Bi-fold frame into sub-sill will give a higher water resistance number. Continuous co-extruded Santoprene bulb seals flyscreen frame to sub-sill. Shim and fix flyscreen sill to floor @ 600mm max. cts. Continuous seal flyscreen frame to floor finish in this area.

Flyscreen Frame Height = H + 8

H = O/A Height

6mm Shims under sub-sill.

10mm Shims under flyscreen sill. Fix both sub-sill and flyscreen sill to floor finish.

87

213
Recessing the Bi-fold sill and flyscreen sill into the floor finish is possible but pleas note there is no water resistance.

Flyscreen Frame Height = H + 31

Shim and fix flyscreen sill to floor @ 600mm max. cts.

H = O/A Height

29

10

35mm Shims under Bi-fold sill.

6mm Shims under flyscreen sill.

For the latest accessories refer our web site:

225 www.awscommercial.com.au

AWS COMMERCIAL ARCHITECTURAL INFORMATION DETAILS SUBJECT TO CHANGE WITHOUT NOTICE

110.11

40

20

36

44

20

411 BI-FOLD DOOR - HORIZONTAL ACCESSORIES


DATE MAR 08 REPLACES MAR 07 SCALE NTS

Flush jamb opening

Galvanised building-in lug used to secure flyscreen frame to wall, fit lugs @ 450mm max. cts. This detail shows how the internal wall lining could be tucked into the flyscreen frame.

Jamb extender used to extend the jamb to align with flydoor jamb. Jamb cavity closer fitted to allow main frame fixing. Pack to prevent main frame dishing. Fix jamb to cavity closer @ 450mm max. cts. before fitting the Bi-fold jamb adaptor 81624. Span-on Bi-fold jamb adaptor. 81647

23

Flyscreen stile location when screen is open.

Maximum flyscreen width www.awscommercial.com.au

Flyscreen Frame Width = W + 46

The maximum flyscreen width varies depending on the Flyscreen frame height. If the Flyscreen frame height <= 2450mm then the maximum flyscreen width would be 3050mm. If the Flyscreen frame height > 2450mm and <= 3000mm then the maximum flyscreen width would be 2400mm.

W = O/A Width

Flyscreen stile runs up to magnetic strip in the jamb closer. This page shows the flyscreen frame fitted behind 3L door combination, make sure the flyscreen does not exceed the absolute maximum flyscreen width. Single opening flyscreen can be fitted to other Bi-fold door that open to one side only as long as you don't exceed the absolute maximum single screen width.

Alternative 26mm step in the brick skins removes the need for jamb extender.

Important Note: The flyscreen frame can only be fixed to the 44mm jambs as shown left and is not suitable for retro fitting. This page shows the flyscreen frame fitted behind 3L door combination.

For the latest accessories refer our web site:

110.12

26

AWS COMMERCIAL ARCHITECTURAL INFORMATION DETAILS SUBJECT TO CHANGE WITHOUT NOTICE

23

411 BI-FOLD DOOR - HORIZONTAL ACCESSORIES


DATE MAR 08 Flush jamb opening REPLACES MAR 07 SCALE NTS

Jamb extender used to extend the jamb to align with flydoor jamb. Jamb cavity closer fitted to allow main frame fixing. Pack to prevent main frame dishing. Fix jamb to cavity closer @ 450mm max. cts. before fitting the Bi-fold jamb adaptor. Snap-on Bi-fold jamb adaptor. Flydoor stile location when screen is open.

23

Maximum flyscreen width

Flydoor Frame Width = W + 46

The maximum single flyscreen width varies depending on the Flyscreen frame height. If the Flyscreen frame height <= 2450mm then the maximum single flyscreen width would be 3050mm or 6100mm on a double if the screens met in the middle. If the Flyscreen frame height > 2450mm and <= 3000mm then the maximum single flyscreen width would be 2400mm or 4800mm on a double if the screens met in the middle.

W = O/A Width

Important Note: This page shows the flyscreen frame fitted behind 3L 1R door combination with the screen door meeting at French meeting stiles. This is only possible if the door leaves are not too wide and the screen does not exceed the maximum width. On other four panel combinations 4L, 4R and 2L2R the screen door would meet in the middle. Flyscreens can be fitted to other door combinations as long as they don't exceed the absolute maximum double screen width.

Flush jamb opening

23

For the latest accessories refer our web site:

www.awscommercial.com.au

scale: not to scale

AWS COMMERCIAL ARCHITECTURAL INFORMATION DETAILS SUBJECT TO CHANGE WITHOUT NOTICE

110.13

102mm SUB-SILLS ACCESSORIES


DATE MAR 08 REPLACES MAR 07 SCALE FULL SIZE & NTS

102mm Sub-sill

Suit any of the 102mm frames including: Series 400 CentreGLAZE Series 406 FrontGLAZE Series 407 FACELINE Series 702 SlideMASTER 102mm sub-sill fitted with custom injection moulded nylon end caps as shown on following page. Fix sub-sill to structure @ 450mm maximum centres.

Drainage slots @ 400mm centres. Series 400 frame illustrated.

Alternative flat sub-sill

Seal sub-sill to structure in this area.

CAD file: DWG or DXF AWS_Install_2

Drainage slots @ 400mm centres.

For the latest accessories refer our web site:

www.awscommercial.com.au

110.14

AWS COMMERCIAL ARCHITECTURAL INFORMATION DETAILS SUBJECT TO CHANGE WITHOUT NOTICE

102mm SUB-SILLS ACCESSORIES


DATE MAR 08 REPLACES MAR 07 SCALE NOT TO SCALE

Two piece sub-jamb is notched over sub-sill.

We have a stop-end that wraps around the junction of 102mm sub-sill and sub-jamb.

For the latest accessories refer our web site:

www.awscommercial.com.au

AWS COMMERCIAL ARCHITECTURAL INFORMATION DETAILS SUBJECT TO CHANGE WITHOUT NOTICE

110.15

NAILING FIN SUB-SILL ACCESSORIES


DATE MAR 08 REPLACES MAR 07 SCALE FULL SIZE & NTS

Nailing fin sub-sill

Is the standard sub-sill under commercial windows. Important Note: Overall frame height includes the nailing fin sub-sill and is measured to the external lower edge, refer 'Q'.

Series 462 sliding window sill illustrated.

Caulking sub-sill to frame seal.

Frame spacer.

Nailing-fin sub-sill.

CAD file: DWG or DXF AWS_462_1

Moulded nylon end caps complete this sub-sill installation.

End caps sealed into sub-sill. 20 x 6mm drainage slots @ 400mm max. cts. Drainage slots covered with PVC cover flap. Sub-sill will accept sill flap. For the latest accessories refer our web site: www.awscommercial.com.au

110.16

AWS COMMERCIAL ARCHITECTURAL INFORMATION DETAILS SUBJECT TO CHANGE WITHOUT NOTICE

NAILING FIN SUB-SILL ACCESSORIES


DATE MAR 08 REPLACES MAR 07 SCALE NOT TO SCALE

The stop-ends on this sub-sill nest into the jambs and are flush with the overall width. This means that they won't clash with reveal linings. Nailing fin sub-sill can be fitted with PVC sill flap to close off the gap between frame and structure.

Sub-sill screwed to sill with stainless steel self tapping screws before installation. The nailing fin sub-sill is designed to be factory fitted to AWS commercial frames and windows.

For the latest accessories refer our web site:

www.awscommercial.com.au

AWS COMMERCIAL ARCHITECTURAL INFORMATION DETAILS SUBJECT TO CHANGE WITHOUT NOTICE

110.17

102mm WINDOW INTO SUB-HEAD & JAMB ACCESSORIES


DATE MAR 08 REPLACES MAR 07 SCALE FULL SIZE

102mm Sub-head

Will accept any 102mm commercial frame.

Fix the sub-head to structure @ 450mm max. centres. Seal to structure on the inner line to match up with the sub-sill caulking.

CAD file: DWG or DXF AWS_Install_2

102mm Sub-jamb

Will accept any 102mm commercial frame.

Fix the sub-jamb base to structure @ 450mm max. centres. Seal to structure on the inner line to match up with the sub-sill caulking.

After fitting the commercial frame apply the inner sub-jamb closer trim.

For the latest accessories refer our web site:

www.awscommercial.com.au

110.18

AWS COMMERCIAL ARCHITECTURAL INFORMATION DETAILS SUBJECT TO CHANGE WITHOUT NOTICE

150mm SUB-SILL ACCESSORIES


DATE MAR 08 REPLACES MAR 07 SCALE FULL SIZE & NTS

150mm Sub-sill

Suit any of the 150mm frames including: Series 606 FrontGLAZE Series 607 FACELINE Series 702 SlideMASTER

A feature with the AWS 150mm sub-sills is the central support leg.This leg also has the drainage slots to allow water escape to the outside. Drainage slots @ 400mm centres. CAD file: DWG or DXF AWS_Install_2 Fix sub-sill to structure @ 450mm maximum centres.

Alternative flat sub-sill

Injection moulded nylon sub-sill end caps. Seal sub-sill to structure in this area.

Drainage slots @ 400mm centres. For the latest accessories refer our web site: www.awscommercial.com.au

AWS COMMERCIAL ARCHITECTURAL INFORMATION DETAILS SUBJECT TO CHANGE WITHOUT NOTICE

110.19

102mm SUB-SILL ACCESSORIES


DATE MAR 08 REPLACES MAR 07 SCALE FULL SIZE

102mm Sub-sill

Suits any of the 102mm frames including: Series 704 SlideMASTER Drainage slots @ 400mm centres. External drainage slots covered with co-extruded Santoprene anti blow-back flap. Fix sub-sill to structure @ 450mm maximum centres.

102mm

102mm Extended Sub-sill

Suits any of the 102mm frames including: Series 704 SlideMASTER

CAD file: DWG or DXF AWS_Install_2 For the latest accessories refer our web site: www.awscommercial.com.au

110.20

AWS COMMERCIAL ARCHITECTURAL INFORMATION DETAILS SUBJECT TO CHANGE WITHOUT NOTICE

150mm SUB-SILL ACCESSORIES


DATE MAR 08 REPLACES MAR 07 SCALE FULL SIZE & NTS

150mm Sub-sill

Suits any of the 150mm frames including: Series 704 SlideMASTER

A feature with the AWS 150mm sub-sills is the central support leg. This leg also has the drainage slots to allow water to escape.

150mm Drainage slots @ 400mm centres. External drainage slots are covered with co-extruded Santoprene anti blow-back flap. Fix sub-sill to structure @ 450mm maximum centres.

Injection moulded nylon sub-sill end caps. Seal sub-sill to structure in this area. CAD file: DWG or DXF AWS_Install_2 For the latest accessories refer our web site: www.awscommercial.com.au
AWS COMMERCIAL ARCHITECTURAL INFORMATION DETAILS SUBJECT TO CHANGE WITHOUT NOTICE

110.21

150mm FRAMING INTO SUB-HEAD & JAMB ACCESSORIES


DATE MAR 08 REPLACES MAR 07 SCALE FULL SIZE

150mm Sub-head

Will accept any 150mm commercial frame. Fix the sub-head to structure @ 450mm max. centres. Seal to structure on the inner line to match up with the sub-sill caulking.

CAD file: DWG or DXF AWS_Install_2

150mm Sub-jamb

Will accept any 150mm commercial frame. Fix the sub-jamb base to structure @ 450mm max. centres. Seal to structure on the inner line to match up with the sub-sill caulking.

For the latest accessories refer our web site:

www.awscommercial.com.au

110.22

AWS COMMERCIAL ARCHITECTURAL INFORMATION DETAILS SUBJECT TO CHANGE WITHOUT NOTICE

EXTRUDED ALUMINIUM BUILDING-IN LUG ACCESSORIES


DATE MAR 08 REPLACES MAR 07 SCALE FULL SIZE & NTS

Adjustable galvanised steel building-in lug, suitable for cavity brick construction. Position lugs @ 450mm maximum centres, may be reduced in high wind load areas.

Lug suits: 30mm and 44mm nailing fin jambs on Series 400 CentreGLAZE (illustrated right). Series 462 Sliding window. Series 463 Double-hung window. Series 464 Double-hung window. Series 466 Awning window. Series 467 Awning window.

CAD file: DWG or DXF AWS_install_2

Adjustable extruded aluminium building-in lug, suitable when fitting 102mm shopfront into existing openings. Position lugs @ 450mm maximum centres, this may reduce in higher wind load areas.

Lug suits: 400 CentreGLAZE open back frames including the commercial windows. 406 FrontGLAZE 102mm open back frames. 407 FACELINE 102mm open back frames. 410 FoldMASTER jambs and head. 701 SlideMASTER jambs and head. 702 SlideMASTER 102mm jambs and head. 704 SlideMASTER 102mm jambs and head. For the latest accessories refer our web site: www.awscommercial.com.au

AWS COMMERCIAL ARCHITECTURAL INFORMATION DETAILS SUBJECT TO CHANGE WITHOUT NOTICE

110.23

WINDOW TO FRAMING SNAP COUPLERS ACCESSORIES


DATE MAR 08 REPLACES MAR 07 SCALE FULL SIZE

102mm Coupler

This coupler is designed to join any 102mm window - typical windows shown below: Series 601 Magnum Sliding window. Series 602 Magnum Sliding window. Series 613 Magnum Double-hung window. Series 610 ClearVENT sashless double-hung window. Series 616 Magnum Awning window. to any of the 102mm AWS shopfront frames: Series 400 CentreGLAZE shopfront. Series 406 FrontGLAZE shopfront. Series 407 FACELINE shopfront. Series 410 FoldMASTER bi-fold doors. Series 701 SlideMASTER sliding windows. Series 702 SlideMASTER sliding doors. Series 704 SlideMASTER sliding doors.

150mm Coupler

This coupler is designed to join any 102mm window - typical windows shown below: Series 601 Magnum Sliding window. Series 602 Magnum Sliding window. Series 613 Magnum Double-hung window. Series 610 ClearVENT sashless double-hung window. Series 616 Magnum Awning window. to any of the 150mm AWS shopfront frames: Series 606 FrontGLAZE shopfront. Series 607 FACELINE shopfront. Series 702 SlideMASTER sliding doors. Series 704 SlideMASTER sliding doors.

CAD file: DWG or DXF AWS_Install_2 For the latest accessories refer our web site: www.awscommercial.com.au

110.24

AWS COMMERCIAL ARCHITECTURAL INFORMATION DETAILS SUBJECT TO CHANGE WITHOUT NOTICE

WINDOW TO FRAMING SNAP COUPLERS ACCESSORIES


DATE MAR 08 REPLACES MAR 07 SCALE NOT TO SCALE

102mm Coupler

This snap fit coupler is designed to join 102mm residential windows to 102mm commercial framing.

Internal view of Series 613 Magnum double-hung window clipped to Series 400 CentreGLAZE shopfront framing.

External view of Series 613 Magnum double-hung window clipped to Series 400 CentreGLAZE shopfront framing.

For the latest accessories refer our web site:

www.awscommercial.com.au

AWS COMMERCIAL ARCHITECTURAL INFORMATION DETAILS SUBJECT TO CHANGE WITHOUT NOTICE

110.25

NAILING FIN FRAME EXTERNAL CLOSER ACCESSORIES


DATE MAR 08 REPLACES MAR 07 SCALE FULL SIZE & NTS

Rotate the closer trim into the main frame.

CAD file: DWG or DXF AWS_Install_2

Can be fitted to any of the nailing fin frame sections. This trim would be useful when frames are being installed into stud walls with external wall cladding. For the latest accessories refer our web site: www.awscommercial.com.au

Nailing fin frame closer

110.26

AWS COMMERCIAL ARCHITECTURAL INFORMATION DETAILS SUBJECT TO CHANGE WITHOUT NOTICE

NAILING FIN FRAME INTERNAL CLOSER ACCESSORIES


DATE MAR 08 REPLACES SCALE FULL SIZE & NTS

Used to create a platform for a second line of reveal fixings.

Internal frame closer

Series 462 sliding window head illustrated. Closer can also be used on other products that will accept the nailing fin frame: Series 463 Commercial double-hung window. Series 464 ClearVENT window. Series 466 Commercial awnings & casements. Series 467 Commercial awnings & casements. Series 400 CentreGLAZE. The closer can be fitted to head, sill and or jambs.

CAD file: DWG or DXF AWS_462_1

Optional internal nailing fin frame filler used to allow extra reveal fixings as shown on previous page. Internal filler would stop on top of and be sealed to the nailing fin sub-sill stop end.

Nailing fin sub-sill stop end.

For the latest accessories refer our web site:

www.awscommercial.com.au

AWS COMMERCIAL ARCHITECTURAL INFORMATION DETAILS SUBJECT TO CHANGE WITHOUT NOTICE

110.27

INTERNAL PERIMETER TRIM ACCESSORIES


DATE MAR 08 REPLACES SCALE FULL SIZE

Dimension 'X'

The dimension 'X' varies depending on the wall and cladding thickness and the framing thickness. The table below is a guide to what the dimension should be with a couple of typical wall and cladding thicknesses: Frame Wall 102mm 100 102mm 100 102mm 90 102mm 90 102mm 75 102mm 75 102mm 64 102mm 64 80mm 64 80mm 64 Serrated angle trim Cladding 10 13 10 13 10 13 10 13 10 13 dim 'X' 11.50 8.50 6.50 3.50 - 0.50 2.50 - 6.50 - 3.50 4.30 1.30

The main trim varies depending on the wall thickness. Typical 102mm frame installed into 90mm stud wall with 10mm Gyprock lining both sides.

CAD file: DWG or DXF AWS_install_2 10 90mm stud wall illustrated 10

The 80mm narrow framing can also be used as shown left into 64mm metal stud wall with 10mm Gyprock lining both sides.

For the latest accessories refer our web site:

www.awscommercial.com.au

110.28

AWS COMMERCIAL ARCHITECTURAL INFORMATION DETAILS SUBJECT TO CHANGE WITHOUT NOTICE

INTERNAL PERIMETER TRIM ACCESSORIES


DATE MAR 08 REPLACES SCALE NOT TO SCALE

Channel trim installation:


Fix main trim to the frame filler at the correct position with blind rivets @ approximately 450mm centres. The correct position varies depending on the stud and wall lining thicknesses, refer previous page. Place frame into wall opening with the main angle hard up against the wall lining. Drill fixing holes through main frame and trim in the glazing pocket area @ approx. 450mm centres. Fit shims between the main trim and studs at fixing points. Don't tighten the fixing screws. Fit serrated angle trim by pushing it into the gap between main frame and the main trim. With the serrated angle tight against the wall lining tighten the fixing screws, this will lock the serrated trim into position. Glaze the frame.

Note: The fixing screw is not tightened until the serrated angle trim is fitted. Serrated angle trim. The details on this page show 90mm stud wall with 10mm Gyprock linings.

Main trim varies depending on wall thickness.

CAD file: DWG or DXF AWS_install_2

Note: This is an internal trimming system. Not recommended for external walls.

For the latest accessories refer our web site:

www.awscommercial.com.au

AWS COMMERCIAL ARCHITECTURAL INFORMATION DETAILS SUBJECT TO CHANGE WITHOUT NOTICE

110.29

FLYDOOR ADAPTOR ACCESSORIES


DATE MAR 08 REPLACES SCALE FULL SIZE & NTS

Flydoor adaptor secretly screwed to shopfront frame @ 450mm max. cts.

The 80mm gap between flydoor and main glass door suits most door furniture.

CAD file: DWG or DXF AWS_install_2

32

Mitred corners fitted with aluminium gusset. 8# Csk. head s.s. self tapping screws.

80

For the latest accessories refer our web site:

www.awscommercial.com.au

110.30

AWS COMMERCIAL ARCHITECTURAL INFORMATION DETAILS SUBJECT TO CHANGE WITHOUT NOTICE

Das könnte Ihnen auch gefallen