Beruflich Dokumente
Kultur Dokumente
Topic
list or product label.
Description
Mandatory. This information can be obtained from the delivery
NETWORKING
Networking scenario: Private network and VPN: private Public network access through IPSec: public
Mandatory
S_POE_RF1 S_POE_RF2
Optional. In PoE power supply mode, the BTS3900B only supports one TRX. This information is used to disable the other TRX.
S_BTSIP
Optional. In private network and VPN, this parameter should be set when the static IP address of the BTS is required.
S_BTSIPMASK
Subnet mask
Optional. In private network and VPN, this parameter should be set when the static IP address of the BTS is required.
S_GWIP
Optional. In private network and VPN, this parameter should be set when the static IP address of the BTS is required.
S_BSCIP
Optional. In private network and VPN, this parameter should be set when the static IP address of the BTS is required.
S_BSCIPMASK
Optional. In private network and VPN, this parameter should be set when the static IP address of the BTS is required.
S_VLANSWITCH
Optional. In private network and VPN, this parameter should be set when the static IP address of the BTS is required.
S_VLANFLAG
Optional. In private network and VPN, this parameter should be set when the static IP address of the BTS is required. Optional. In private network and VPN, this parameter should be set when the static IP address of the BTS is required.
S_VLANPRI
Topic
Description
Mandatory. This parameter can be obtained from the delivery list or product label.
NETWORKING
Networking scenario: Private network and VPN: private Public network access through IPSec: public
Mandatory
S_POE_RF1 S_POE_RF2
Optional. In PoE power supply mode, the BTS3900B only supports one TRX. This parameter is used to disable the other TRX.
IPADDR
Optional. In public network access through IPSec mode, the static IP address of the BTS should be set.
IPMASK
Optional
S_STATIC_IPGW
Optional. In public network access through IPSec mode, the static IP gateway is used to configure default route during the setting of BTS static IP address.
Optional Set either the IP address or the domain name. When you choose to set the domain name, the DNS should be configured in the network and properly set.
M2000_DHCPServer_IP
Set either the IP address or the domain name. When you choose to set the domain name, the DNS should be configured in the network and properly set.
GW_LOCAL_ID
Type of IKE local authentication: name: Indicates that the IKE authentication is performed by the domain name.
Mandatory. The type of the IKE local authentication must be the same as the type of the IKE peer authentication on the SeGW.
Item
Topic
ip: Indicates that the IKE authentication is performed by the IP address.
Description
GW_REMOTE_ID
Type of the IKE peer authentication: name: Indicates that the IKE authentication is performed by the domain name. ip: Indicates that the IKE authentication is performed by the IP address.
Mandatory. The type of the IKE peer authentication must be the same as the type of the IKE remote authentication on the SeGW.
GW_LOCAL_NAME
The IKE local name that is used during the tunnel establishment with the PSeGW
Optional This parameter is configured only when GW_LOCAL_ID is set to name. The IKE local name must be the same as the IKE peer name on the PSeGW.
GW_ROMOTE_NAME
The IKE remote name that is used during the tunnel establishment with the PSeGW
Optional This parameter is configured only when GW_ROMOTE_ID is set to name. The IKE remote name must be the same as the IKE local name on the PSeGW.
GWS_LOCAL_NAME
The IKE local name that is used during the tunnel establishment with the BSC SeGW
Optional This parameter is configured only when GW_LOCAL_ID is set to name. The IKE local name must be the same as the IKE remote name on the BSC SeGW.
GWS_REMOTE_NAME
The IKE remote name that is used during the tunnel establishment with the BSC SeGW
Optional This parameter is configured only when GW_ROMOTE_ID is set to name. The IKE remote name must be the same as the IKE local name on the BSC SeGW.
PRE_SHARED_KEY
Pre-shared key
Mandatory The key is used for authentication when an IPSec tunnel is established with the PSeGW. The key must be the same as that on the PSeGW.
Procedure
1. Connect the USB disk to the USB port of the BTS3900B directly or through a USB data cable. Check the status of the RUN/ALM LED on the BTS3900B panel.
If ... The RUN/ALM LED is green and blinks on for 0.125 s and off for 0.125 s
Then ... It indicates that preconfiguration data file is being loaded to the equipment.
2. 3. 4.
WARNING: When the RUN/ALM LED is green and blinks on for 0.125 s and off for 0.125 s, do not remove the USB disk. After the preconfiguration file is loaded, wait one or two minutes. After the BTS is reset, check the status of the RUN/ALM LED on the BTS3900B panel.
If ... The RUN/ALM LED is green and blinks on for 1 s and off for 1 s
5. 6.
Remove the USB disk or USB data cable from the USB port on the side of the BTS3900B. Check the transmission between the BTS3900B and the BSC on the LMT.