Beruflich Dokumente
Kultur Dokumente
P N M T
ASOLINK
ETWORK
ANAGEMENT
ERMINAL
NEC Corporation
Copyright 2009
ROI-S06986
Table of Contents
1. 2. 3. 4. 5. 6. 7. 8.
Installation Sequence ............................................................................................................................ 1 Phone and Modem Options Setting (Standard 19.2 Kbps Connection) .......................................... 2 Installation of USB Com Port Driver (USB Connection)................................................................... 7 Dial-up Setting ..................................................................................................................................... 10 SNMP Service Setting ......................................................................................................................... 21 PNMT Setup ........................................................................................................................................ 26 Network Connections Setting on Windows XP................................................................................. 31 Launching PNMT................................................................................................................................ 40
-i-
ROI-S06986
1.
Installation Sequence
Only Administrator group privilege level users are authorized to configure the following settings, (1) Dial-up Connection Step 1: Modem Setting
Network Element (NE) other than PASOLINK NEO Standard 19200bps Modem Setting (Phone and Modem Options Setting)
(2) Ethernet Connection Step 1: Pasolink Network Management Terminal (PNMT) Setup
-1-
ROI-S06986
2.
(2)
Click the Phone and Modem Options icon in the Control Panel window to start configuring the modem.
-2-
ROI-S06986
(3)
Enter your country and area code in the Location Information window. Click [OK].
(4)
-3-
ROI-S06986
(5)
Select the Modem tab. Click [Add] to continue with adding the new modem for the PNMT.
(6)
-4-
ROI-S06986
(7)
Select Standard Modem Types from the list of Manufacturers and Standard 19200bps Modem from the Models. Click [Next] to continue.
(8)
-5-
ROI-S06986
(9)
(10) Verify that Standard 19200 bps Modem and COM1 are displayed. Click [OK].
-6-
ROI-S06986
3.
(2)
Select Install from a list or specific location [Advanced] and click on [Next].
-7-
ROI-S06986
(3)
Insert the USB driver CD-ROM in the computers disk drive and select Search for the best driver in these locations and check Search removable media [floppy, CD-ROM ...] then, click [Next].
(4)
-8-
ROI-S06986
(5)
(6)
-9-
ROI-S06986
4.
Dial-up Setting
(1) Click Start | Settings | Control Panel and the Network Connections icon to start configuring the Dialup setting.
(2)
The Network Connections window appears. Click Create a new connection in the Network Tasks area.
- 10 -
ROI-S06986
(3)
The Welcome to the New Connection Wizard window appears. Click [Next].
(4)
- 11 -
ROI-S06986
(5)
(6)
NOTE This screen appears only when a USB Modem Driver has been installed.
- 12 -
ROI-S06986
(7)
In the New Connection Wizard window, input connection name into Company Name field. Click [Next]. In case of connecting with RS232C-Type [PNMT(RS232C)]
- 13 -
ROI-S06986
(8)
Enter any number in the Phone number field and click [Next] to continue.
- 14 -
ROI-S06986
(9)
You can also create a shortcut on your desktop if desired. Click [Finish]. RS232C connection
USB connection
- 15 -
ROI-S06986
(10) In the Connect Dial-up Connection window, click [Cancel] to continue. Click Properties in the Connect Dial-up Connection window.
(11) In the Properties Window click on the General tab. Click [Configure].
RS232C setting
USB setting
- 16 -
ROI-S06986
RS232C setting
USB setting
(13) Retain the default setting on the Options tab and click the Security tab.
RS232C setting
USB setting
- 17 -
ROI-S06986
(14) Retain the default setting on the Security tab and click the Networking tab.
RS232C setting
USB setting
(15) On the Networking tab, verify that PPP ... is`displayed in the Type of dial-up server I am calling field and uncheck File and Printer ... and Client for Microsoft....
RS232C setting
USB setting
- 18 -
ROI-S06986
(16) Click Settings Uncheck all the boxes in the window that appears, as shown below. Click [OK] to go back to the previous window. Highlight Internet Protocol (TCP/IP) and then click [Properties].
(17) Verify that both Obtain an IP address automatically and Obtain DNS server address automatically are selected.
- 19 -
ROI-S06986
(18) In the Advanced TCP/IP Settings window, uncheck Use IP header compression for the PPP link. Click [OK].
(19) Retain the default setting on the Advanced tab and click [OK].
- 20 -
ROI-S06986
5.
To Remove SNMP Service: (1) Select Start Setting Control Panel, then, in the Add or Remove Programs window, click Add/Remove Windows Components.
(2) The Windows Components Wizard window appears. Remove the check from Management and Monitoring Tools, and then click Details ...
- 21 -
ROI-S06986
(3) The Management and Monitoring Tools window appears. Confirm that Simple Network Management Protocol is not checked and click [OK]. Return to above window and click [Next].
- 22 -
ROI-S06986
To Stop SNMP Service: (5) To stop SNMP Service without removing it, click Administrative Tools in the Control Panel window.
- 23 -
ROI-S06986
(7) Confirm that SNMP Service is installed and it has started automatically. Select Action Properties on the menu bar in the Services window, or right-click SNMP Service and then click Properties in the SNMP Service pop-up menu.
(8) Select Manual in the Startup type field and click Stop in the Service status field on the General tab. Click [OK] or [Apply].
- 24 -
ROI-S06986
(9) Confirm that the Status of both SNMP Service and SNMP Trap Service is stopped, and that the startup condition for each one is Manual.
- 25 -
ROI-S06986
6.
PNMT Setup
NOTE If PNMT software has already been installed, please uninstall it before you install a new version.
(1) Insert the PNMT Installation CDROM.Open the CDROM folder and double-click install.exe.
- 26 -
ROI-S06986
(4) Specify the directory in which the PNMT is to be installed. Click [Next]. Restore Default Folder: Click this button to choose the license key folder Choose: Click this button to select another directory
NOTE The default path is C:\PNMSj. It is not possible to include blank spaces as in Program Files. (C denotes the directory where the currently running OS is installed)
- 27 -
ROI-S06986
(5) Specify the License Key file if one is available. Click [Next]. Restore Default Folder: Click this button to revert to default path Choose: Click this button to choose the license key file
IMPORTANT: IMMEDIATE IMPORT OF LICENSE You may use the PNMT on a trial basis for 30 days. After that the PNMT can ONLY be used IF the license has been imported (activated). To obtain the license please contact NEC.
- 28 -
ROI-S06986
- 29 -
ROI-S06986
(8) If PNMT Installation CDROM contains ADM Management Tool, the tool also is installed
- 30 -
ROI-S06986
7.
Select Start
Control Panel
(2)
Select the Network and Internet Connections from the Control Panel window.
- 31 -
ROI-S06986
(3)
Select the Network Connections from the Network and Internet Connections window.
(4)
- 32 -
ROI-S06986
(5)
Right click the Local Area Connection and select the Properties from the context menu.
(6)
The following Local Area Connection Properties window will appear as default.
- 33 -
ROI-S06986
(7)
Confirm that the Internet Protocol (TCP/IP) is only checked on the General tab, and then click on the Authentication tab.
(8)
- 34 -
ROI-S06986
(9)
Remove the check on the Enable network access control using IEEE 802.1X, and then click on the Advanced tab.
(10) The following Advanced tab will be displayed, and confirm that there is no check on the Advanced tab.
- 35 -
ROI-S06986
(11) Return to the General tab and select the Internet Protocol (TCP/IP), then click on the Properties button.
- 36 -
ROI-S06986
(12) The following Internet Protocol (TCP/IP) Properties window will appear. Select the Use the following IP Address instead of the Obtain an IP address automatically. Set the IP address, Subnet mask and Default gateway as follows:
Item IP Address Subnet mask Default gateway Setting 172.17.254.254 255.255.255.252 172.17.254.253
- 37 -
ROI-S06986
(13) The following Advanced TCP/IP Settings window will appear. IP Settings, DNS, and WINS are not required. Select the TCP/IP filtering on the Options tab and click on Properties button.
- 38 -
ROI-S06986
(14) The following TCP/IP Filtering window will appear. Confirm that there is no check on the Enable TCP/IP Filtering (All adapters) and all the Permit All on the TCP Ports, UDP Ports and IP Protocols are selected. Click on OK button returning to Local Area Connection Properties windows.
(15) Click on Close button from Local Area Connection Properties window to complete the Network Connections Setting on Windows XP.
- 39 -
ROI-S06986
8.
Launching PNMT
(1) Click Start | Programs |PNMTj |PNMT to start the application.
(2) If the following window appears, select [Unblock] (when using the Windows XP SP2 Firewall).
- 40 -
ROI-S06986
(3) Enter User name and Password, and Select the Connection Entry. After installation of the PNMT, the initial password will be:User name: Password: admin (There is no initial password. Just press Enter. A password can then be set.) Connection: In case of connection to 5000S and PASOLINK NEO/a select Ethernet and PNMT(LAN/Direct) entry. Otherwise select Dialup and PNMT(RS232C)/PNMT(USB) entry.
NOTE If another application is using the SNMP Port, application initialization will not be possible; the application will shut down, and the following message will appear.
- 41 -