Beruflich Dokumente
Kultur Dokumente
1
II B.Tech II Semester Supplimentary Examinations, Aug/Sep 2008
STRUCTURAL ANALYSIS-I
(Civil Engineering)
Time: 3 hours Max Marks: 80
Answer any FIVE Questions
All Questions carry equal marks
⋆⋆⋆⋆⋆
Figure 3
4. Develop the slope-deflection equations for analyzing continuous beams and portal
frames. Illustrate their application. [16]
5. Define Strain energy. Derive an expression for strain energy due to bending mo-
ment. [16]
6. A uniform load of 30kN/m, 5m long, crosses a girder 20m span. Calculate the
maximum S.F and B.M at a section 8m from the left support. Also find out the
maximum shear and the absolute maximum BM in the beam. [16]
7. A warren girder of 60m span is built up of triangles and has ten panels of 6m each.
Draw the influence line for the left hand diagonal in the fourth panel from the left
hand support. State the exact position of a single rolling load in the panel so that
the force in the diagonal is zero. [16]
8. (a) What are the Advantages and disadvantages of statically indeterminate trusses?
(b) Explain how castigluauos theorem provides an elegant method of solution to
indeterminate trusses by considering one example? [6+10]
⋆⋆⋆⋆⋆
1 of 1
Code No: R05220106 Set No. 2
II B.Tech II Semester Supplimentary Examinations, Aug/Sep 2008
STRUCTURAL ANALYSIS-I
(Civil Engineering)
Time: 3 hours Max Marks: 80
Answer any FIVE Questions
All Questions carry equal marks
⋆⋆⋆⋆⋆
1. Draw the bending moment and shear force diagram of a propped cantilever beam
of span 6m due to a point load of 6 kN at the mid span. [16]
Figure 3
4. Develop the slope-deflection equations for analyzing continuous beams and portal
frames. Illustrate their application. [16]
5. In the pin jointed frame shown in Figure 5, if joint B undergoes horizontal and
vertical displacements of magnitude δu , δv respectively. Find the magnitude of the
load that is applied at B. If A1 , A2 andL1 , L2 represent the area of c/s and lengths
of the members AB and BC respectively, with E as modulus of elasticity then what
shall be the force required if the joint B has no horizontal shift. [16]
Figure 5
6. The system of concentrated loads shown below rolls from left to right on a girder
of span 16m, 30kN load leading. For a section 4m from left support , determine
1 of 2
Code No: R05220106 Set No. 2
the maximum B.M and S.F:
Wheel load (kN) : 20 50 50 40 30
Spacing (m) : 1.5 1.5 2 1 [16]
8. (a) Cite Two examples of structures that have the same degree of static and
kinematic indeterminacy.
(b) Three wires AD, BD and CD having the same cross sectional area and of same
material support a load W as shown in Figure 8. Determine the tensions in
three wires. [6+10]
Figure 8
⋆⋆⋆⋆⋆
2 of 2
Code No: R05220106 Set No. 3
II B.Tech II Semester Supplimentary Examinations, Aug/Sep 2008
STRUCTURAL ANALYSIS-I
(Civil Engineering)
Time: 3 hours Max Marks: 80
Answer any FIVE Questions
All Questions carry equal marks
⋆⋆⋆⋆⋆
2. Find the fixed end moments for a fixed beam of span 6 m subjected to a concen-
trated clockwise moment of 10 kNm at 2.5 m from the left end. [16]
4. Develop the slope-deflection equations for analyzing continuous beams and portal
frames. Illustrate their application. [16]
5. Define Strain energy. Derive an expression for strain energy due to bending mo-
ment. [16]
6. A load 80kN/m and, 4m long, rolls over a girder of 30m span. Calculate the
equivalent uniformly distributed load. [16]
7. A pratt girder consists of eight panels, each 3.5m square, the loading being on the
lower bottom. Draw the influence line for the force in the diagonal of the of the
third panel from the left and determine the maximum tension and compression in
it due to uniformly distributed load of 100kN/m, 10m long. [16]
8. While Fabricating the pin pointed frame shown in Figure 8; the member AC was
the last member to be fitted, and was found to be 1mm short of the resumed lasted.
Find the force in AC the diagonal members are 1000mm2 in area while others are
2000mm2 in area E = 200Gpa. [16]
1 of 2
Code No: R05220106 Set No. 3
Figure 8
⋆⋆⋆⋆⋆
2 of 2
Code No: R05220106 Set No. 4
II B.Tech II Semester Supplimentary Examinations, Aug/Sep 2008
STRUCTURAL ANALYSIS-I
(Civil Engineering)
Time: 3 hours Max Marks: 80
Answer any FIVE Questions
All Questions carry equal marks
⋆⋆⋆⋆⋆
1. Draw the bending moment and shear force diagram of a propped cantilever beam
of span 6m due to a point load of 6 kN at the mid span. [16]
2. Find the fixed end moments for a fixed beam of span 6 m subjected to a concen-
trated clockwise moment of 10 kNm at 2.5 m from the left end. [16]
4. During loading the support B of the continuous beam shown in figure 4. Sinks by
10mm. Obtain the support moments by the slope-deflection method and sketch
the B.M.D. [16]
Figure 4
5. Determine the vertical displacement of joint C of the truss. Cross sectional area of
each member A= 300mm2 , E= 2× 105 N/mm2 . Solve using Castigliano’s theorem.
Shown in Figure 5. [16]
Figure 5
1 of 2
Code No: R05220106 Set No. 4
6. A single rolling load of 120kN rolls along a girder of 12m span. Draw the diagrams
of maximum B.M and maximum S.F (positive and negative). [16]
7. A pratt girder consists of eight panels, each 3.5m square, the loading being on the
lower bottom. Draw the influence line for the force in the diagonal of the of the
third panel from the left and determine the maximum tension and compression in
it due to uniformly distributed load of 100kN/m, 10m long. [16]
8. (a) Cite Two examples of structures that have the same degree of static and
kinematic indeterminacy.
(b) Three wires AD, BD and CD having the same cross sectional area and of same
material support a load W as shown in Figure 8. Determine the tensions in
three wires. [6+10]
Figure 8
⋆⋆⋆⋆⋆
2 of 2