Beruflich Dokumente
Kultur Dokumente
SINHGAD TECHNICAL EDUCATION SOCIETY SINHGAD COLLEGE OF ENGINEERING, VADGAON (BK), PUNE 411 041. DEPARTMENT OF E&TC ENGINEERING
SE E&TC
EXPERIMENT NO: 01 TITLE: - STUDY OF COMPONENTS AND INTEGRATED CIRCUITS. CLASS: - S.E. E&TC BATCH: DATE:ROLL NO: -
SE E&TC
TITLE: - STUDY OF COMPONENTS AND INTEGRATED CIRCUITS. AIM:- A) Study the components 1. Resistors 2. Capacitor 3. Diode 4. BJTs 5. FET B) Study the method for soldering. APPRATUS: -1. Solder gun tool kit. 2. Sample diode and BJTs. THEORY: - Write following questions: 1] Explain the different types of resistors in detail. 2] How to measure the value of resistor using four band colors? Give three examples. 3] Explain the different types of capacitors in detail. Give at least two examples. 4] How to measure the value of capacitor? 5] Explain the different types of Diode in detail? 6] Explain in detail BJTs and FET. 7] What do you understand by IC Packages?
SE E&TC
8] Explain the procedure of soldering for the electronic components. CONCLUSION: 1] Comment on the advantages and application of using soldering technique.
NOTE: - Attach the datasheet of the components used in practical.
SE E&TC
EXPERIMENT NO: 02 TITLE: - STUDY OF DIGITAL MULTIMETER CLASS: - S.E. E&TC BATCH: DATE:ROLL NO: -
SE E&TC
TITLE: - STUDY OF DIGITAL MULTIMETER. AIM:- To measure 1. AC and DC voltages. 2. AC and DC current. 3. Value of resistance and continuity test. 4. Hfe diode and BJT testing. APPRATUS: - 1. Digital multimeter with probes. 2. Sample resistor, diode and transistor. 3. Power supply. THEORY: - Write following questions: 1] Explain digital multimeter specification. 2] Draw the neat and labeled block diagram of DMM. 3] Explain different types of converters used in multimeter? 4] Explain the fuses and batteries used in DMM? 5] Can we measure the hfe value of BJT if yes then how? 6] Explain how to measure resistor value on DMM and how to test diode. 7] DMM shows the value of voltage reading but it not showing the value of current. What could be probable problem in DMM?
SE E&TC
SE E&TC
EXPERIMENT NO: 03 TITLE: - STUDY OF TRANSFORMER AND INDUCTOR. CLASS: - S.E. E&TC BATCH: DATE:ROLL NO: -
SE E&TC
TITLE: - STUDY OF TRANSFORMERS AND INDUCTORS. AIM:- To study 1. Types of transformer. 2. Types of inductor. APPRATUS: - 1. Digital multimeter with probes.
2.
THEORY: - Write following questions: 1] What is transformer? Explain the basic principle of transformer in detail. 2] What are the different types of transformers? 3] What do you mean by inductor? Explain the construction and basic operating Principle of inductor. 4] Enlist and explain the types of inductors.
SE E&TC
EXPERIMENT NO: 04 TITLE: - STUDY OF LABORATORY INSTRUMENTS. CLASS: - S.E. E&TC BATCH: DATE:ROLL NO: -
SE E&TC
10
TITLE: - STUDY OF LABORATORY INSTRUMENTS. AIM:- To study 1. Signal generator. 2. Function generator. 3. DC Regulated power supplies
APPRATUS: - 1. Signal generator, Function generator, DC Regulated power supplies 2. CRO. THEORY: - Write following questions: 1] Give the technical specification of signal generator. 2] Explain the front panel of signal generator. 3] Write the procedure to check various front panel controls. 4] Give the technical specification of function generator. 5] What is the advantage of using function generator over signal generator? Explain it. 6] Give the procedure for generating any three types of signal and explain How we set frequency and amplitude of signal. 7] Explain technical specification for DC power supply. CONCLUSION: -1] Give the application and advantages for using signal generator, function generator and DC power supply.
SE E&TC
11
EXPERIMENT NO: 05 TITLE: - STUDY OF OSCILLOSCOPES CLASS: - S.E. E&TC BATCH: DATE:ROLL NO: -
SE E&TC
12
TITLE: - STUDY OF OSCILLOSCOPES. AIM:- To study of various control on front panel of dual channel storage Oscilloscope. 1. Measuring of voltage frequency and time. 2. Storing charging and discharging waveforms of RC circuits DSO.Measure rise and fall times. 3. Store signals at different trace locations and retrieve it. 4. Find out propagation delay of logic gate.
5. Connect function generator output to DSO and observe different wavefo different frequency. APPRATUS: - 1. Digital Storage Oscilloscope, probe, resistor, capacitor, Breadboard THEORY: - Write following questions: 1] Draw and explain the block diagram of DSO. 2] Draw the front panel of DSO and explain: a) Vertical controls b) Horizontal controls c) Trigger controls d) Menu and control button 3] How do you measure frequency, amplitude and pulse width using DSO. 4] How the measurements are taken automatically using DSO. 5] How do you measure propagation delay on oscilloscope? Give steps to measure Propagation delay.
SCOE, DEPT. OF E&TC ENGG. SE E&TC 13
SE E&TC
14
EXPERIMENT NO: 06 TITLE: - STUDY OF FREQUENCY COUNTER. CLASS: - S.E. E&TC BATCH: DATE:ROLL NO: -
SE E&TC
15
TITLE: - STUDY OF FREQUENCY COUNTER. AIM: - To study of various control on front panel of dual channel storage oscilloscope. Measurement of frequency, time period.
APPRATUS: - Frequency counter, probes. THEORY: - Write following questions: 1] Draw the basic block diagram of a frequency counter and explain. 2] Explain the gating function using proper waveform example. 3] What is the use of temperature compensated crystal oscillator in the time base circuit. 4] Explain the input signal processing with diagram. 5] How will you measure period of a given signal using frequency counter. 6] Explain the following errors i) Gating error ii) time base error iii) trigger level error. 7] What problems are associated with the measurement of pulsed signals? CONCLUSION: 1] Give the application and advantages for using frequency counter
SE E&TC
16
EXPERIMENT NO: 07 TITLE: - STUDY OF PCB DESIGNING AND SMALL PROJECT ON BREADBOARD CLASS: - S.E. E&TC BATCH: DATE:ROLL NO: -
SE E&TC
17
TITLE: - STUDY OF PCB DESIGNING AND SMALL PROJECT ON BREADBOARD. AIM: - To study of various techniques of PCB designing and make small project on bread board. THEORY: - Write following questions: 1] Explain the different types of PCB designing PROJECT: - Make the small project on bread board / PCB. CONCLUSION: 1] Make small report of your project.
SE E&TC
18