Sie sind auf Seite 1von 3

3.

Once the root bridge has been determined, which two items are assigned to every other
switch before STP converges a switched network? (Choose two.) VLAN ID designated port

6. Refer to the exhibit. Assuming that the RIPv1 routing protocol is enabled and all networks have been correctly configured on each router, which statement is true? Some of the packets from H1 that are destined to H2 will be sent to the switch that is connected to network 192.168.3.64/26.
10.

Refer to the exhibit. Which access list, when applied inbound to the Fa0/0 interface of router R1, will prevent all IP traffic from the 172.16.1.16 network from entering the 172.16.1.32 network while allowing all other traffic? access-list 101 deny tcp 172.16.1.16 0.0.0.15 172.16.1.32 0.0.0.7 access-list 101 permit ip any any
11.

Which three IP addresses are valid host addresses in the 10.200.0.0/20 network? (Choose three.) 10.200.11.69 10.200.16.1 10.201.0.55
12.

What factor is important to consider when configuring manual summarization with EIGRP? Networks that are being summarized must use the same subnet mask. 15. Refer to the exhibit. What is the purpose of assigning the IP address 192.168.30.1 to an access layer switch? to allow hosts on the same LAN to connect to each other

20. Which command should a network administrator issue to disable default summarization in an EIGRP network? Router(config-router)# no auto-summary 22. Refer to the exhibit. A network technician has added router R0 to an existing network that contains router R1. R0 is configured with EIGRP and is connected to R1 via the Fa0/0 interface of each router. After completing an analysis of the network, the technician notices that the routes to the networks that are supported by routers R0 and R1 are not being exchanged. What is a possible cause for this failure? FastEthernet interfaces on R0 are in a shutdown state. 24. Refer to the exhibit. What is the administrative distance for OSPF routes? 65 25 What is a feature of PAP authentication? It sends the username/password pair across the link in clear text. 37 What is a limitation of RIPv1? RIPv1 does not send subnet mask information in its updates.
38.

Refer to the exhibit. Which commands would be used to configure OSPF on router R1? R1(config)# router ospf 1 R1(config-router)# network 10.10.10.0 0.0.0.255 area 0 R1(config-router)# network 172.16.1.16 0.0.0.15 area 0 R1(config-router)# network 172.16.1.32 0.0.0.7 area 0 R1(config-router)# network 192.168.88.0 0.0.0.3 area 0 R1(config-router)# network 192.168.88.4 0.0.0.3 area 0 R1(config-router)# network 192.168.88.8 0.0.0.3 area 0

39. Refer to the exhibit. How many routers have established OSPF adjacencies with R1? 4 42. Refer to the exhibit. In order to establish a default route to the ISP, which two commands need to be issued on R2 so that R1 receives a default route from R2? (Choose two.) R2(config-router)# area 0 range 0.0.0.0 0.0.0.0 R2(config)# ip route 0.0.0.0 0.0.0.0 serial 0/0/1 45. Refer to the exhibit. The network administrator wants to restrict the Production network from accessing the HR network. All other traffic will have access to all networks. Which combination of interface and direction should the administrator use to apply the ACL? Fa0/1, in 47. Refer to the exhibit. All routes in the exhibit are available to a router. Which two routes will be placed into the routing table? (Choose two.) D E 48. Refer to the exhibit. Routers R1 and R2 are directly connected via interface Serial0/0 on each router but they are unable to communicate. What could be the cause of the problem? Both interfaces require a no shutdown command to be issued.

Das könnte Ihnen auch gefallen