Beruflich Dokumente
Kultur Dokumente
HELIX DSP 3S - 148x210mm - 01 02 2021 - Web
HELIX DSP 3S - 148x210mm - 01 02 2021 - Web
DSP.3S
Digitaler High-Res 8-Kanal Signalprozessor mit
96 kHz / 24 Bit Signalweg
Digital High-Res 8-channel signal processor with
96 kHz / 24 Bit signal path
Herzlichen Glückwunsch!
Sehr geehrter Kunde, Dieser Prozessor wurde von uns nach neuesten
technischen Erkenntnissen entwickelt und zeichnet
Wir gratulieren Ihnen zum Kauf dieses hochwer- sich durch hervorragende Verarbeitung und eine
tigen HELIX-Signalprozessors. überzeugende Anwendung ausgereifter Technolo-
gien aus.
Audiotec Fischer setzt mit dem HELIX DSP.3S neue
Maßstäbe im Bereich der Signalprozessortechnik. Viel Freude an diesem Produkt wünscht Ihnen das
Dabei profitieren Sie als Kunde direkt von unserer Team von
nahezu 30-jährigen Erfahrung in der Forschung und
Entwicklung von Audiokomponenten. AUDIOTEC FISCHER
Allgemeine Hinweise
Allgemeines zum Einbau von HELIX-Kompo- sind. Diese könnten sonst beschädigt werden. Ach-
nenten ten Sie bitte darauf, dass sich solche Teile auch in
der doppelten Wandverkleidung verbergen können.
Um alle Möglichkeiten des Produktes optimal aus-
schöpfen zu können, lesen Sie bitte sorgfältig die Allgemeines zum Anschluss des HELIX DSP.3S
nachfolgenden Installationshinweise. Wir garantie- Signalprozessors
ren, dass jedes Gerät vor Versand auf seinen ein-
wandfreien Zustand überprüft wurde. Der Signalprozessor darf nur in Kraftfahrzeuge ein-
gebaut werden, die den 12 V-Minuspol an Masse
Vor Beginn der Installation unterbrechen Sie haben. Bei anderen Systemen können der HELIX
den Minusanschluss der Autobatterie. Signalprozessor und die elektrische Anlage des Kfz
Wir empfehlen Ihnen, die Installation von einem beschädigt werden. Die Plusleitung für die gesamte
Einbauspezialisten vornehmen zu lassen, da der Anlage sollte in einem Abstand von max. 30 cm von
Nachweis eines fachgerechten Einbaus und An- der Batterie mit einer Hauptsicherung abgesichert
schlusses des Gerätes Voraussetzung für die werden. Der Wert der Sicherung errechnet sich aus
Garantieleistungen sind. der maximalen Stromaufnahme der Car-Hifi Anla-
ge.
Installieren Sie Ihren HELIX DSP.3S an einer tro-
ckenen Stelle im Auto und vergewissern Sie sich, Verwenden Sie zum Anschluss des Signalpro-
dass der Signalprozessor am Montageort genü- zessors an die Stromversorgung des Fahrzeugs
gend Kühlung erhält. Montieren Sie das Gerät ausschließlich den beiliegenden Anschlussste-
nicht in zu kleine, abgeschlossene Gehäuse ohne cker!
Luftzirkulation oder in der Nähe von wärmeabstrah-
lenden Teilen oder elektronischen Steuerungen des Die Kabelverbindungen müssen so verlegt sein,
Fahrzeuges. Im Sinne der Unfallsicherheit muss dass keine Klemm-, Quetsch- oder Bruchgefahr be-
der Signalprozessor professionell befestigt werden. steht. Bei scharfen Kanten (Blechdurchführungen)
Dieses geschieht über Schrauben, die in eine Mon- müssen alle Kabel gegen Durchscheuern gepols-
tagefläche eingeschraubt werden, die wiederum tert sein. Ferner darf das Versorgungskabel niemals
genügend Halt bieten muss. mit Zuleitungen zu Vorrichtungen des Kfz (Lüfter-
motoren, Brandkontrollmodulen, Benzinleitungen
Bevor Sie die Schrauben im Montagefeld befesti- etc.) verlegt werden.
gen, vergewissern Sie sich, dass keine elektrischen
Kabel und Komponenten, hydraulische Bremslei-
tungen, der Benzintank etc. dahinter verborgen
2
Anschluss- und Bedienelemente
1 2 3 4 5
6 7 8 9 10 11
3
Inbetriebnahme und Funktionen
Der HELIX DSP.3S wird wie nachfolgend be- 2. Anschluss der Highlevel-Lautsprecherein-
schrieben an das Autoradio angeschlossen. gänge
Die Hochpegel-Lautsprechereingänge kön-
Achtung: Für die Durchführung der nachfolgenden nen direkt mit den Lautsprecherausgängen
Schritte werden Spezialwerkzeuge und Fachwissen des Werks- bzw. Nachrüstradios mit Hilfe ent-
benötigt. Um Anschlussfehler und Beschädigungen sprechender Kabel (Lautsprecherkabel mit
zu vermeiden, fragen Sie im Zweifelsfall Ihren Ein- max. 1 mm² Querschnitt) verbunden werden.
bauspezialisten und beachten Sie zwingend die Sollten Sie ein normales Werksradio anschlie-
allgemeinen Anschluss- und Einbauhinweise (siehe ßen, empfehlen wir folgende Kanalbelegung:
Seite 2). Kanal A = Vorne links
Kanal B = Vorne rechts
1. Anschluss der Vorverstärkereingänge Kanal C = Hinten links
Diese Eingänge (Line Input) können mit ent- Kanal D = Hinten rechts
sprechenden Kabeln (RCA / Cinch-Kabel) an Dabei müssen nicht zwingend alle Eingän-
die Vorverstärker- / Lowlevel- / Cinch-Aus- ge belegt werden. Werden nur zwei Kanäle
gänge des Radios angeschlossen werden. Im belegt, empfehlen wir die Kanäle A und B zu
Signalprozessor lassen sich die Signaleingän- verwenden. Achten Sie bitte auf eine korrekte
ge über die DSP PC-Tool Software frei den Vor- Polung! Wenn Sie einen oder mehrere An-
verstärkerausgängen (Line Output) zuweisen. schlüsse verpolen, kann dadurch die Funktion
Die Einschaltautomatik des Signalprozessors des Signalprozessors beeinträchtigt werden.
funktioniert bei den Vorverstärkereingängen Bei Verwendung dieses Eingangs muss der
nicht, so dass der Remote-Eingang zwingend Remote-Eingang nicht belegt werden, da sich
belegt werden muss. der Signalprozessor automatisch einschaltet,
Achtung: Der Highlevel- und der Vorverstär- sobald ein Lautsprechersignal anliegt.
kersignaleingang eines einzelnen Kanals darf
nicht gleichzeitig genutzt werden, da dies zu 3. Anschluss einer digitalen Signalquelle
Schäden an ihrem Autoradio führen kann. Es ist Sofern Sie über eine Signalquelle mit koaxialem
aber zulässig, an einem Kanal den Highlevel- oder optischem Digitalausgang verfügen, kann
und an einem anderen Kanal den Vorverstär- diese an den Signalprozessor angeschlossen
kersignaleingang zu verwenden. werden. Werkseitig ist der Optical Input aktiviert
6
und die manuelle Einschaltung des Eingangs 2.
Schalten Sie den Signalprozessor ein
über eine optionale Fernbedienung konfiguriert. und starten anschließend die Soft-
Möchten Sie den Eingang automatisch, bei An- ware. Die Funktion finden Sie im Tab
liegen eines Audiosignals, aktivieren, können „Signalverwaltung“ des DCM-Menüs unter
Sie dies in der DSP PC-Tool Software unter dem Punkt „Main Input → Input Gain“.
dem Menüpunkt Signalmanagement im DCM
konfigurieren.
Die Einschaltautomatik des Signalprozessors
funktioniert bei Verwendung eines Digitalein-
gangs nicht, so dass der Remote-Eingang des 3. Drehen Sie die Lautstärke Ihres Radios auf
Power Inputs zwingend belegt werden muss. 90 % der Gesamtlautstärke und spielen Sie
Wichtig: Das digitale Audiosignal einer Quel- ein geeignetes Testsignal, z.B. Rosa Rau-
le ist üblicherweise nicht lautstärkegeregelt. schen, (Vollaussteuerung 0 dB) ab.
Das bedeutet, dass an den Signalausgängen 4. Sollte die Clipping Anzeige im DSP PC-Tool
des HELIX DSP.3S der volle Pegel anliegt bereits rot leuchten (siehe Markierung im
und die angeschlossenen Verstärker voll aus- folgenden Bild), verringern Sie mit Hilfe des
gesteuert werden. Dies kann im Extremfall Schiebereglers die Eingangsempfindlich-
die Lautsprecher zerstören. Wir raten deshalb keit, bis die Clipping Anzeige erlischt.
dringend dazu, eine optionale Fernbedienung
zur Einstellung der Lautstärke der digitalen
Signaleingänge zu verwenden!
Hinweis: Der HELIX DSP.3S kann nur unkom-
primierte, digitale Stereo PCM-Signale mit ei- 5. Erhöhen Sie die Eingangsempfindlichkeit
ner Abtastrate zwischen 12 kHz und 96 kHz / bis die Clipping Anzeige aufleuchtet. Schie-
192 kHz verarbeiten. Es können keine MP3- ben Sie nun den Regler zurück bis die Clip-
oder Dolby-codierten Daten verarbeitet werden, ping Anzeige wieder erlischt.
sondern ausschließlich Stereosignale.
gering, trotzdem sollten Kabel mit mind. 1 mm² Inbus- und vier Kreuzschlitzschrauben) lösen.
Querschnitt für die Spannungsversorgung ver- Nun können Sie das Bodenblech aus dem
wendet werden. Kühlkörper zur Seite hinausziehen und e rhalten
so Zugriff auf den Schalter. Dieser befindet sich
6. Anschluss des Remote-Eingangs in der Nähe des „Made in Germany“ Siegels
Der Remote-Eingang des Power Inputs muss (siehe Markierung im nachfolgenden Bild).
mit dem Remote-Ausgang des Steuergeräts
(Radio) verbunden sein, sofern die Vorverstär-
kereingänge (Line Input) oder der Digitalein-
gang (Optical Input) des Signalprozessors als
Signaleingänge / Signaleingang genutzt wer-
den / wird.
Es wird dringend davon abgeraten, den
Remote-Eingang des Signalprozessors über
das Zündungsplus des Fahrzeugs zu steuern,
um Störgeräusche beim Ein- und Ausschalten
zu vermeiden.
Bei Verwendung des Hochpegel-Lautsprecher
eingangs (Highlevel Input) muss der Remote-
Eingang nicht belegt werden, sofern das ange-
schlossene Radio über BTL-Ausgangsstufen On: Einschaltung über Hochpegel-Lautspre-
verfügt. chereingang aktiviert (Werkseinstellung).
Off:
Einschaltung über Hochpegel-Lautspre-
7. Konfiguration des Remote-Eingangs chereingang deaktiviert.
Die Einschaltung des HELIX DSP.3S erfolgt au-
tomatisch bei Ansteuerung über die Hochpegel- 8. Konfiguration des DSPs
Lautsprechereingänge (Highlevel Input) oder Es wird dringend empfohlen, vor der ersten
sobald ein Remote-Signal am Remote-Eingang Inbetriebnahme die grundlegenden Einstel-
anliegt. Mit Hilfe des „Auto Remote“-Schalters lungen im DSP mit Hilfe der DSP PC-Tool
kann die automatische Einschaltung deaktiviert Software vorzunehmen.
werden (Auto Remote = Off). Dies sollte vorge- Eine Missachtung kann zur Zerstörung der
nommen werden, wenn es beispielsweise zu angeschlossenen Verstärker / der Lautspre-
Störgeräuschen beim Ein- und Ausschalten des cher führen. Informationen zum Anschluss des
Signalprozessors kommt. Signalprozessors an einen PC finden Sie auf
Hinweis: Wird die automatische Einschaltung Seite 9.
des Signalprozessors deaktiviert, muss der
Remote-Eingang belegt werden. Eine auto- 9. Anschluss des Remote-Ausgangs
matische Einschaltung über den Hochpegel- Dieser Ausgang dient dazu, einen am Line
Lautsprechereingang ist dann nicht mehr mög- Output angeschlossenen Verstärker mit einem
lich. Remote-Signal zu versorgen. Bitte verwenden
Hinweis: Werkseitig ist die automatische Ein- Sie ausschließlich dieses Signal zur Einschal-
schaltung über den Hochpegel-Lautsprecher tung externer Verstärker, um Ein- und Aus-
eingang des DSP.3S aktiviert. schaltgeräusche zu vermeiden.
Um die automatische Einschaltung zu
deaktivieren, muss das Gerät geöffnet und die
Schalterposition des „Auto Remote“-Schalters
geändert werden. Dazu entfernen Sie bitte das
Seitenblech der Geräteseite mit dem USB-
Eingang indem Sie die fünf Schrauben (eine
8
Anschluss an den Computer
Der HELIX DSP.3S kann mit Hilfe der DSP PC‑Tool 1. Laden Sie die DSP PC-Tool Software unter
Software frei konfiguriert werden. Die Software www.audiotec-fischer.com herunter und in-
stellt alle Funktionen übersichtlich und bediener- stallieren diese auf ihrem Computer.
freundlich zur Verfügung, so dass Sie diese indi- 2. Schließen Sie danach den DSP.3S mit dem
viduell einstellen können. Dabei können alle acht beiliegenden USB-Kabel an den Computer an.
DSP Kanäle separat eingestellt werden. Wenn Sie längere Distanzen zu überbrücken
Bevor Sie den HELIX DSP.3S das erste Mal an ei- haben, verwenden Sie bitte eine aktive USB-
nen Computer anschließen, gehen Sie auf unsere Verlängerung mit integriertem Repeater oder
Homepage und laden die aktuellste Software Ver- das optional erhältliche WIFI CONTROL Inter-
sion des DSP PC-Tools herunter. Es ist ratsam, face.
regelmäßig nach Updates der Software zu schau- 3. Schalten Sie erst den Signalprozessor ein und
en, damit das Gerät immer auf dem aktuellsten starten Sie anschließend die Software. Sofern
Stand ist. die Betriebssoftware des DSPs nicht mehr ak-
tuell ist, wird diese automatisch aktualisiert.
Die Software sowie eine umfangreiche Knowledge 4. Nun können Sie den HELIX DSP.3S mithilfe der
Base finden Sie auf www.audiotec-fischer.com. DSP PC-Tool Software frei konfigurieren. Nütz-
Es wird dringend empfohlen, die DSP PC-Tool liche Hinweise zur korrekten Einstellung ent-
Knowledge Base vor der ersten Benutzung durch- nehmen Sie unserer Knowledge Base, welche
zulesen, um Komplikationen und Fehler zu vermei- auf unserer Webseite bereit steht.
den.
Achtung: Es wird dringend empfohlen, vor der
Wichtig: Stellen Sie sicher, dass der H
ELIX DSP.3S ersten Inbetriebnahme die Lautstärke am Radio
bei der ersten Installation der Software noch nicht auf Minimum zu drehen und an die Vorverstärker
an den PC angeschlossen ist. Verbinden Sie diesen ausgänge des DSP.3S noch nichts anzuschlie-
erst, wenn die Software samt der USB-Treiber voll- ßen, bis die grundlegenden Einstellungen im
ständig installiert ist! Signalprozessor vorgenommen wurden. Speziell
bei Verwendung in vollaktiven Systemen besteht
Im folgenden Abschnitt lesen Sie die wichtigsten sonst Zerstörungsgefahr für die Lautsprecher.
Schritte zum Anschluss und der ersten Inbetrieb-
nahme:
9
Konfigurationshinweise für die DSP-Soundeffekte
Der HELIX DSP.3S bietet einzigartige DSP-Sound FX-Menüs die „Active Setup Link“-Funktion
effekte wie das „Augmented Bass Processing“, den durch Setzen eines Hakens.
„StageXpander“, den „RealCenter“ und noch mehr.
Um in den Genuss der DSP-Soundeffekte zu kom-
men, müssen bei der Hard- und Softwarekonfigu-
ration bestimmte Einstellungen vorgenommen wer-
den. 5. Wiederholen Sie die Schritte zwei und drei für
alle genutzten Routing-Matrizen.
Hinweise für das Center Processing mit seiner 6. Wechseln Sie nun in das FX-Menü und aktivieren
RealCenter- und ClarityXpander-Funktion im Reiter „Center Processing“ den gewünschten
Um die RealCenter- und ClarityXpander-Funktion für Soundeffekt durch Setzen eines Hakens.
einen Center-Lautsprecher nutzen zu können, müs-
sen folgende Schritte durchgeführt werden:
1. Sie benötigen mindestens ein linkes und ein
rechtes analoges oder digitales Eingangssignal.
2. Öffnen Sie das IO-Menü im DSP PC-Tool. Rou-
ten Sie das linke und das rechte analoge oder
digitale Eingangssignal (kein Summensignal) auf
die Ausgangskanäle A und B (siehe Beispiel im Hinweis: Das Center Processing wird je nach Laut-
nachfolgenden Bild). Es spielt dabei keine Rolle sprecher-Setup (aktiv oder passiv) ausschließlich
ob der Ausgangskanal als Front-, Rear-, Center- auf den Ausgangskanal G bzw. die Ausgangskanä-
Kanal etc. definiert ist. le F und G angewendet.
Für ein passives Setup definieren Sie den Aus- Hinweise für das Augmented Bass Processing
gangskanal G als „Center Full“. Der Kanal F mit seiner Dynamic Bass Enhancement- und
bleibt unberücksichtigt. SubXpander-Funktion
Auch für das Augmented Bass Processing müssen
bestimmte Einstellungen vorgenommen werden,
um dessen Soundeffekte anwenden zu können.
1. Sie benötigen entweder ein Mono- oder Stereo-
4. Nur bei aktivem Setup durchführen: Aktivie- Eingangssignal (analog oder digital).
ren Sie nun im Reiter „Center Processing“ des 2. Öffnen Sie das IO-Menü im DSP PC-Tool. Rou-
10
ten Sie alle linken und rechten analogen oder
digitalen Eingangssignale auf den Ausgangska-
nal H.
3. Wiederholen Sie das Routing für alle genutzten Hinweis: Das Augmented Bass Processing wird aus-
Routing-Matrizen. schließlich auf den Ausgangskanal H angewendet.
4. Wechseln Sie nun in das FX-Menü und aktivie-
ren den gewünschten Soundeffekt durch Setzen
eines Hakens.
ACO Plattform-Features
Neben den einzigartigen DSP-Soundeffekten bietet werden. Werkseitig sind die Speicherbereiche eins
die ACO-Plattform des DSP.3S zusätzlich eine Viel- und zwei ausgewählt. Um zwischen allen internen
zahl an System-Features. Speicherplätzen umschalten zu können, werden die
Im DCM Menü der DSP PC-Tool Software können optional erhältlichen Fernbedienungen DIRECTOR
für einige dieser System-Features individuelle Ein- und CONDUCTOR oder die HELIX WIFI CONTROL
stellungen vorgenommen werden. empfohlen.
Der HELIX DSP.3S kann durch die Montage einer 6. Achten Sie auf den richtigen Sitz des HEC Mo-
HELIX Extension Card (HEC) um weitere Funk- duls und darauf, dass alle Kontaktstifte vollstän-
tionen erweitert werden – beispielsweise um eine dig im Sockel stecken.
Bluetooth® Audio Streaming Funktion, einer High
Resolution Audio USB Soundkarte etc. erweitert
werden.
Zur Montage einer HEC muss das Seitenblech des
DSP.3S demontiert und gegen das der HEC beilie-
gende Seitenblech ausgetauscht werden.
Achtung: Installieren Sie ausschließlich für den
DSP.3S vorgesehene HEC Module an der dafür
vorgesehenen Position. Die Benutzung eines
nicht für das Gerät spezifizierten HEC Moduls
oder eine Installation an einer nicht dafür vorge-
sehenen Position im Gerät kann zu Schäden am
HEC Modul, dem Signalprozessor, des Radios
oder anderen angeschlossenen Geräten führen.
12
Spezielle Features des HELIX DSP.3S
13
Technische Daten
Eingänge..........................................................................6 x Cinch
6 x Hochpegel-Lautsprechereingang
1 x Optisch SPDIF-Format (12 - 96 kHz)
1 x Koaxial SPDIF-Format (12 - 192 kHz)
1 x Remote In
Eingangsempfindlichkeit...................................................Cinch: 2 - 4 Volt
Hochpegel: 5 - 11 Volt
Ausgänge.........................................................................8 x Cinch
1 x Remote Out
Ausgangsspannung..........................................................6 Volt
Frequenzbereich..............................................................10 Hz - 44.000 Hz
DSP Leistung....................................................................64 Bit / 295 MHz
Abtastrate.........................................................................96 kHz
DSP Typ...........................................................................Audio Signalprozessor
Signalwandler...................................................................A/D: BurrBrown
D/A: BurrBrown
Signal- / Rauschabstand (A-bewertet).............................Digitaleingang: 112 dB
Analogeingang: 107 dB
Klirrfaktor (THD+N)...........................................................Digitaleingang: < 0,0008 %
Analogeingang: < 0,002 %
Intermodulationsverzerrungen..........................................Digitaleingang: < 0,003 %
Analogeingang: < 0,005 %
Übersprechen...................................................................> 90 dB
Betriebsspannung �����������������������������������������������������������9,6 - 18 Volt (max. 5 Sek. bis hinab zu 6 Volt)
Leistungsaufnahme..........................................................DC 12 V 3 A max.
Stromaufnahme................................................................< 450 mA
Max. Remote-Ausgangsstrom..........................................500 mA
Zusätzliche Features........................................................HEC Slot, Masseschalter, Smart Control Port,
32 Bit CoProcessor, ADEP.3-Schaltkreis, Auto
Remote-Schalter
Abmessungen (H x B x T)................................................40 x 177 x 120 mm
Garantiehinweis
Die Garantieleistung entspricht der gesetzlichen Technische Änderungen und Irrtümer vorbehalten!
Regelung. Von der Garantieleistung ausgeschlos- Für Schäden am Fahrzeug oder Gerätedefekte, her-
sen sind Defekte und Schäden, die durch Überla- vorgerufen durch Bedienungsfehler des Gerätes,
stung oder unsachgemäße Behandlung entstanden können wir keine Haftung übernehmen. Dieses
sind. Eine Rücksendung kann nur nach vorheriger Produkt ist mit einer CE-Kennzeichnung versehen.
Absprache in der Originalverpackung, einer de- Damit ist das Gerät für den Betrieb in Fahrzeugen
taillierten Fehlerbeschreibung und einem gültigen innerhalb der Europäischen Union (EU) zertifiziert.
Kaufbeleg erfolgen.
Hinweis:
„Die Bluetooth® Wortmarke und die Logos sind eingetragene Warenzeichen der Bluetooth SIG, Inc. und jegliche Nutzung dieser Marken
durch die Audiotec Fischer GmbH geschieht unter Lizenz. Andere Handelsmarken und Handelsnamen gehören den jeweiligen Inhabern.“
14
Congratulations!
Dear Customer,
Congratulations on your purchase of this innovative We wish you many hours of enjoyment with your
and high-quality HELIX product. new HELIX DSP.3S.
General instructions
General installation instructions for HELIX General instruction for connecting the HELIX
components DSP.3S signal processor
To prevent damage to the unit and possible injury, The HELIX DSP.3S signal processor may only be
read this manual carefully and follow all installation installed in vehicles which have a 12 Volts negative
instructions. This product has been checked for terminal connected to the chassis ground. Any other
proper function prior to shipping and is guaranteed system could cause damage to the signal processor
against manufacturing defects. and the electrical system of the vehicle.
The positive cable from the battery for the entire
Before starting your installation, disconnect sound system should be provided with a main fuse
the battery’s negative terminal to prevent at a distance of max. 30 cm from the battery. The
damage to the unit, fire and / or risk of injury. For value of the fuse is calculated from the maximum
a proper performance and to ensure full warranty total current draw of the car audio system.
coverage, we strongly recommend to get this prod-
uct installed by an authorized HELIX dealer. Use only the provided connectors for connec-
tion of the HELIX DSP.3S. The use of other con-
Install your HELIX DSP.3S in a dry location with suf- nectors or cables can result in damage of the
ficient air circulation for proper cooling of the equip- signal processor, the head unit / radio or the
ment. The signal processor should be secured to connected amplifiers / loudspeakers!
a solid mounting surface using proper mounting
hardware. Before mounting, carefully examine the Prior to installation, plan the wire routing to
area around and behind the proposed installa- avoid any possible damage to the wire harness.
tion location to insure that there are no electrical All cabling should be protected against possible
cables or components, hydraulic brake lines or any crushing or pinching hazards. Also avoid routing
part of the fuel tank located behind the mounting cables close to potential noise sources such as
surface. Failure to do so may result in unpredictable electric motors, high power accessories and other
damage to these components and possible costly vehicle harnesses.
repairs to the vehicle.
15
Connectors and control units
1 2 3 4 5
6 7 8 9 10 11
16
Initial start-up and functions
Nevertheless, there are use cases where it will installed. Connect the signal processor to the
be necessary to directly connect input and output DSP PC-Tool software and confirm the automat-
ground or to tie both grounds together via a resistor. ic update of the operating system. You will find
Therefore the Ground lift switch has three positions: the latest version of the DSP PC-Tool software at
- center position: input and output ground www.audiotec-fischer.com.
separated. Red / green fast flashing: The currently selected
- left position: input and output ground tied sound setup memory is empty. A new setup has to
together. be loaded via the DSP PC-Tool software or switch
- right position: input and output ground to a memory position with existing sound setup.
connected via 200 Ohms resistor.
9 USB input
7 Control pushbutton Connect your personal computer to the DSP.3S
The DSP.3S provides 10 internal memory locations using the provided USB cable. The required PC
for sound setups. The Control pushbutton allows software to configure this signal processor can be
the user to switch between two memory positions. downloaded from the Audiotec Fischer website
These can be defined in the DSP PC-Tool. www.audiotec-fischer.com.
1. Setup switch: Press Control pushbutton for 1 sec- Please note: It is not possible to connect any USB
ond. The memory locations one and two are defined storage devices.
by default. Switching is indicated by a single red
flash of the Status LED. Alternatively, the optional 10 SCP (Smart Control Port)
URC.3 remote control can be used for switching. This multi-functional input is designed for HELIX
To switch between all internal memory locations, DSP.3S accessory products like a remote control
optional accessories like the DIRECTOR display which allows to adjust several features of the signal
remote control, CONDUCTOR or WIFI CONTROL processor. Depending on the type of remote con-
are required. trol, at first its functionality has to be defined in the
2. Device reset: Press pushbutton for five seconds. “Device Configuration Menu” of the DSP PC‑Tool
This completely erases the internal memory and is software.
indicated by a continuous red glowing and constant Attention: If the accessory product does not have
green flashing of the Status LED. a NanoFit connector solely use the NanoFit adaptor
Attention: After erasing the setups from memory which is included in delivery for connection.
the DSP.3S will not reproduce any audio output un-
til the device is updated via the DSP PC-Tool soft-
ware.
8 Status LED
The Status LED indicates the operating mode of the
signal processor and of its memory. NanoFit adaptor
Green: DSP is ready for operation.
Orange: Power Save Mode is active. 11 Line Output
Red: Protection Mode is active. This may have dif- 8-channel pre-amplifier output for connecting power
ferent root causes. The HELIX DSP.3S is equipped amplifiers. The output voltage is 6 Volts max. Please
with protection circuits against over- and under- make sure that you always turn on / off external am-
voltage as well as overheating. Please check for plifiers using the remote output of the signal proces-
connecting failures such as short-circuits or other sors Power Input. Never directly control the external
wrong connections. amps by a signal from the ignition switch of your
If the DSP is overheated the internal temperature car! Additionally this output will be turned off when
protection switches off the remote and signal output the “Power Save Mode” of the signal processor is
until it reaches a safe temperature level again. active. The outputs can be assigned to any of the
Red / green slow flashing: No operating software inputs as desired using the DSP PC‑Tool software.
18
Installation
Connection of HELIX DSP.3S to the head unit / processor. If this input is used the remote input
car radio: does not need to be connected as the signal
processor will automatically turn on once a
Caution: Carrying out the following steps will re- loudspeaker signal is received.
quire special tools and technical knowledge. In or-
der to avoid connection mistakes and / or damage, 3. Connecting a digital signal source
ask your dealer for assistance if you have any ques If you have a signal source with an optical or
tions and follow all instructions in this manual (see coaxial digital output you can connect it to the
page 15). It is recommended that the device will be signal processor using the appropriate input. In
installed by an authorized HELIX dealer. standard configuration the Optical Input is ac-
tivated as well as the manual activation via an
1. Connecting the pre-amplifier inputs optional remote control is configured.
Use the correct cable (RCA / cinch cable) to Alternatively you can activate the automatic
connect these inputs to the pre-amplifier / turn-on feature in the DCM menu of the DSP
lowlevel / cinch outputs of your head unit / car PC-Tool software. The feature activates the
radio. Each input can be assigned to any output configured digital input as soon as a signal is
using the DSP PC-Tool software. The automat- applied to its input.
ic turn-on circuit does not work when using the The automatic turn-on circuit does not work
pre-amplifier inputs. In this case the remote in- when a digital input is used. Therefore it is man-
put has to be connected to activate the HELIX datory to connect the remote input of the Power
DSP.3S. Input.
Important: It is strictly forbidden to use the Important: The signal of a digital audio source
Highlevel and lowlevel Line Input of an indi- normally does not contain any information
vidual channel at the same time as this may about the volume level. Keep in mind that this
cause severe damage to the lowlevel line out- will lead to full level on the outputs of the HELIX
puts of your head unit / car radio. Nevertheless DSP.3S and your connected amplifiers. This
it is possible to use the Highlevel Input of one may cause severe damage to your speakers.
channel and the lowlevel Line Input of another We strongly recommend to use an optional re-
channel simultaneously. mote control for adjusting the volume level of
the digital signal input!
2. Connecting the highlevel speaker inputs Information: The HELIX DSP.3S can only han-
The highlevel loudspeaker inputs can be con- dle uncompressed digital stereo signals in PCM
nected directly to the loudspeaker outputs of an format with a sample rate between 12 kHz and
OEM or aftermarket radio using appropriate ca- 96 kHz / 192 kHz and no MP3- or Dolby-coded
bles (loudspeaker cables with 1 mm² / AWG 18 digital audio stream!
max.).
We recommend the following channel assign- 4. Adjustment of the input sensitivity
ment if a common car radio will be connected to Attention: It is mandatory to properly adapt
the signal processor: the input sensitivity of the DSP.3S to the
Channel A = Front left signal source in order to avoid damage to
Channel B = Front right the signal processor.
Channel C = Rear left The input sensitivity can be optimally adapted to
Channel D = Rear right the signal source using the DSP PC-Tool soft-
Actually it is not mandatory to use all highlevel ware. Input sensitivity is factory set to 11 Volts
speaker inputs. If only two channels will be con- for the Highlevel and 4 Volts for the Line Input.
nected we recommend to use the channels A This is definitely the best setting for most appli-
and B. Make sure that the polarity is correct. If cations. Only if the head unit / car radio doesn ́t
one or more connections have reversed polar- deliver enough output level, the input sensitivity
ity it may affect the performance of the signal should be increased.
19
Installation
The setting affects both the lowlevel and the recommend a minimum wire gauge of 1 mm² /
highlevel inputs! AWG18 for both power supply wires.
Follow the subsequent steps to perfectly adapt 6. Connecting the remote input
the signal processors input sensitivity to your The remote input of the Power Input has to
signal source: be connected to the radio remote output if the
1. Don‘t connect any amplifiers to the outputs signal processors lowlevel Line Inputs or the
of the DSP.3S during this setup. Optical Input is / are used as signal input/s. We
2. First turn on the signal processor and then do not recommend controlling the remote input
start the software. The function can be found via the ignition switch to avoid pop noise during
in the “Signal Management” tab of the DCM turn on / off.
menu under the item “Main Input → Input If the Highlevel Input is used this input does not
Gain“. need to be connected as long as the car radio
has BTL output stages.
Connection to a PC
It is possible to freely configure the HELIX DSP.3S 2. Connect the signal processor to your comput-
with our DSP PC-Tool software. er using the USB cable that is included in de-
The user interface is designed for easy handling of livery. If you have to bridge longer distances
all functions and allows an individual adjustment of please use an active USB extension cable with
each of the eight DSP channels. Prior to connect- integrated repeater or the optionally available
ing the signal processor to your PC visit our web- WIFI CONTROL interface.
site and download the latest version of the DSP 3. First turn on the signal processor and then start
PC‑Tool software. the software. The operating software will be up-
Check from time to time for software updates. You dated automatically to the latest version if it is
will find the software and a huge knowledge base at not up-to-date.
www.audiotec-fischer.com. 4. Now you are able to configure your HELIX
We strongly recommend to carefully read the DSP DSP.3S with our intuitive DSP PC-Tool soft-
PC-Tool knowledge base before using the software ware. Nevertheless, interesting and useful
for the first time in order to avoid any complications hints can be found in our knowledge base at
and failures. www.audiotec-fischer.com.
Important: Make sure that the signal processor is
not connected to your computer before the software Caution: We highly recommend to set the vol-
and USB driver are installed! ume of your car radio to minimum position during
first start-up. Additionally no devices should be
In the following the most important steps how to connected to the signal processor until general
connect and the first start-up are described: settings in the DSP PC-Tool software have been
made. Especially if the DSP.3S will be used in fully
1. Download the latest version of the DSP active applications, a wrong setup can destroy your
PC-Tool software (available on our website speakers right away.
www.audiotec-fischer.com) and install it on
your computer.
21
Configuration notes for the DSP sound effects
22
Notes for Augmented Bass Processing with 4. Now switch to the FX menu and activate the de-
its functions Dynamic Bass Enhancement and sired sound effect by placing a tick.
SubXpander
There are as well some adjustments necessary if
the Augmented Bass Processing and its sound ef-
fects shall be used.
1. You need either a mono or stereo input signal
(analog or digital).
2. Open the IO menu in the DSP PC-Tool. Route
all left and right analog or digital input signals to Note: The Augmented Bass Processing affects only
output channel H. the output channel H.
23
ACO platform features
Beside the unique DSP sound effects the DSP.3S Remote Output Configuration
provides a bunch of new system and DSP features. This function controls if the remote output (which
In the DCM menu of the DSP PC-Tool software in- switches on and off the connected amplifiers) will
dividual settings can be made for several of these be temporarily deactivated during a sound setup
system features. switch. This function is activated (ON) by default.
ADEP.3 Configuration
If the DSP.3S is connected to an OEM radio via the
highlevel inputs it may happen that the ADEP.3 cir-
cuit has to be adapted to the diagnostic mode of the
Turn On & Off Delay radio if the latter is equipped with a so-called “class
This function allows to determine the delay time with SB” output stage”.
which the DSP is switched on and off. The factory The ADEP.3 circuit should be adjusted if there are
setting is 0.2 seconds. The delay time should only e.g. distortions in the upper volume range.
be modified if there are e.g. noises while switching The compatibility mode is disabled by default.
on / off the signal processor.
24
HELIX Extension Card slot (HEC slot)
25
Unique features of the HELIX DSP.3S
Start-Stop capability
The switched power supply of the HELIX DSP.3S
assures a constant internal supply voltage even if
the battery’s voltage drops to 6 Volts during engine
crank.
26
Technical Data
Warranty Disclaimer
The warranty service is based on the statutory reg- Technical modifications and errors excepted! We
ulations. Defects and damage caused by overload accept no liability for damage to the vehicle or
or improper handling are excluded from the warran- device defects caused by the incorrect operation
ty service. Any return can only take place following of the device. This product has been issued a CE
prior consultation, in the original packaging together marking. This means that the device is certified for
with a detailed description of the error and a valid use in vehicles within the European Union (EU).
proof of purchase.
Note: “The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by
udiotec Fischer GmbH is under license. Other trademarks and trade names are those of their respective owners.”
A
27
Audiotec Fischer GmbH
Hünegräben 26 · 57392 Schmallenberg · Germany
Tel.: +49 2972 9788 0 · Fax: +49 2972 9788 88
E-mail: helix@audiotec-fischer.com · Internet: www.audiotec-fischer.com