Beruflich Dokumente
Kultur Dokumente
Rev.1.Jul.25.2005
Build the Small Clone circuit on this layout. The FET switching has been removed to use true bypass switching. Layout shown with depth mod applied, see schematic for depth switch for stock wiring. Pads A, B, C, D, E are for the stereo mod. Off board components except for the potentiometers are not shown on the layout. Trademarks are property of their owners.
1M-C 10k-B 3
47
2.2uF
10k
470k
220uF +
OUT
10uF
220k
56k
LAYOUT
47 AC ADAPTOR 9v INPUT .033 220k +4.5v 6k8 .01
+4.5v
+9v
OTIDALEH
.0033 .033
GND IN
33k 6k8 1k
1uF +
MOC.DAPENOT 5002PF
READY TO TRANSFER
220uF 10uF 56k +4.5v 56k 10uF
POT B CW +4.5v C
+9v E
1k
3 2
+9v IC1a 1 A 22k 20k D 1uF Q1 .0033 .015 470pF D1 12k 180pF 10k 220k 39k 33k 120k 470k 4 3 7 8 MN3007 1 5 2 6 12 11 10 14 9 4 8 CD4047 5 7 6 2 3 1 D3 150pF +9v +9v 100k 10k Q3 10uF 10uF +4.5v +4.5v 1uF 5 10k .0027 6 IC1b 7 1k OUTPUT 10k 33k .01 6k8
+9v Q2
.047
RATE 1M
47k 2.2uF
+9v 180k
68k
3
82k
2
39k*** 10uF
10k
1
Layout and presentation by Francisco Pea 2001-2005. All rights reserved. Authorization for personal use only, any commercial use is forbidden. Permission for posting/serving limited to http://www.tonepad.com Permission refused for posting from other sites.
14 13 12 11 10 9
CD4047
150pF D2
MN3007
10uF +
39k
10uF +
10uF
+9V
Rb=Empty
DEPTH
+ +
1uF + +
Heladito-O2
Rev.1.Jul.25.2005
The Stereo Mod requires a separate board. The original small clone had a depth switch instead of the potentiometer, this gave two depth options only. The layout provides pads for this mod, just follow the schematic for the depth switch. Trademarks are property of their owners. SCHEMATIC FOR THE STEREO MOD
Use the pads on the main PCB and wire this circuit:
22k A 2.2uF 20k 100k C 100k D B E 2 3 8 IC1a 1 5 10k 33k .01 6 IC1b 4 7 1k OUTPUT2 1uF DEPTH 2k7 (Rb) 68k 4k7 (Ra) 39k 10uF 82k 6k8 180k +9v Tant. 2 1 IC2a 3 5 7 Lm358 6 IC2b Lm358 120k 470k
100k
5002 PF
This mod is for changing the value of the 150pF cap going to pin1 of CD4007. Use a SP4T rotary switch wired like this:
C1 C2 C3 C4
STEREO MOD LAYOUT/TRANSFER Parts List Resistors 1 - 47ohm 2 - 1k 1 - 2k7 (2.7k)* 1 - 3k3 (3.3k) 1 - 4k7 (4.7k)* 2 - 6k8 (6.8k) 6 - 10k 1 - 12k 1 - 20k 1 - 22k 3 - 33k 4 - 39k 1 - 47k 2 - 56k 1 - 68k 1 - 82k 1 - 100k 1 - 120k 1 - 180k 2 - 220k 1 - 470k
1 2 3 4
Pots 1 - 1M Rev. Log. 1 - 100k Trim. 1 - 10k Lin.** Capacitors 1 - 150pF 1 - 180pF 1 - 470pF 1 - 0.0027 1 - 0.0033 1 - 0.0047 2 - 0.01 1 - 0.015 1 - 0.033 1 - 0.047 3 - 1uF 1 - 2.2uF Tant. 5 - 10uF 1 - 220uF
Diodes 2 - 1N914 Transistors & ICs IC1 - 4558 IC2 - LM358 1 - CD4047 1 - MN3007 Q1 - 2N5087 Q2 - 2N5088 Q3 - 2N5088
The Math: -1 -1 -1 -1 -1 Pos1=(C1 +C2 +C3 +C4 ) Pos2=(C1-1+C3-1+C4-1)-1 -1 -1 -1 Pos3=(C1 +C4 ) -1 -1 Pos4=(C1 ) =C1
Notes * Only needed if building stock (no depth pot mod) version ** Replace with SPST switch if building stock version
Layout and presentation by Francisco Pea 2001-2005. All rights reserved. Authorization for personal use only, any commercial use is forbidden. Permission for posting/serving limited to http://www.tonepad.com Permission refused for posting from other sites.