Beruflich Dokumente
Kultur Dokumente
Cable open.(5001701)
Major
Critical
Minor
Warning
5 6 7
Gigabit ethernet loss of carrier on port 1.(5004031) IF loopback.(5001601) Link to device is broken(1)
Warning
Critical
10
Minor
11
Major
12
Warning
13 14 15
RFU loopback.(5001722) Synthesizer unlocked.(5001733) TDM backplane LOF for slot #2.(5023012)
16
Warning
17
Warning
18 19 20 21 22
Backup kernel is running.(5000716) Tx mute.(5001735) Unknown(127) Mate IDU communication error.(5001012) Low input voltage.(5000717)
23
LOS in STM-1/OC-3.(5002601)
Critical
24 25
Major Warning
1) Check IF cable and connectors. 2) Verify that N-Type connector inner pin is not spliced. 3) Replace IDU. 4) Replace RFU.
(1) Extension or main unit equipment failure (2) Backplane failure(84) 1) Line is not properly connected. 2) External equipment is faulty.(32) (1) Network TDM trail configuration error (2) Signal failure in TDM trail - this may be due to equipment failure or AIS at the line input (2) Excessive BER in TDM trail (3) Signal degrade in TDM trail(111) 1) Cable is not connected to the port. 2) Cable is defective.(5) 1) User enabled IF loopback.(45) Link to NE is broken(1) 1) Reconnect line. 2) Check line cables. 3) Check external equipment. 4) Power cycle the system.
1) Fade in the link. 2) Defective IF cable. 3) Fault in RFU. 4) Fault in IDU.(17) 1) Fade in the link.(16)
1) Connect cable to the port. 2) Replace cable. 1) Disable IF loopback Check the link. 1) Check IF cable and connectors. 2) Verify that N-Type connector inner pin is not spliced.3) Replace IDU.4) Replace RFU. For High Power RF Unit:Check BMA connector center pin is not spliced both on RFU and on OCB. 1) Check link performance. 2) Check IF cable, and replace if required. 3) Replace RFU. 4) Replace IDU. 1) Check link performance. 2) Check IF cable, and replace if required. 3) Replace RFU. 4) Replace IDU. 1) Check link performance.
1) Check IF cable and connectors. 2) Verify that N-Type connector inner pin is not spliced. 3) Replace IDU. 1) Defective IF cable. 2) IF cable not connected properly. 3) Defective 4) Replace RFU. IDU. 4) Defective RFU.(9) For High Power RF Unit: 1) Check BMA connector on OCB 2) Check BMA connector on RFU 1) Disable RFU loopback. 1) Replace RFU.2) In XPIC mode, replace mate RFU as well. 1) Re-insert unit 2) Power cycle unit 3) Check backplane 1) Replace missing components (IDUs, T-cards) 2) Make sure radio scripts support required number of E1/DS1 trails through radio 3) Delete relevant trails 1) Replace missing components (IDUs, T-cards) 2) Make sure radio scripts support required number of E1/DS1 trails through radio 3) Delete relevant trails 1) Re-install the SW. Unmute the RFU transmitter. 1) Check Protection cable connectivity. 2) Replace Protection cable. 1) Check power supply voltage 1) Reconnect line. 2) Check line cables. 3) Check external equipment. 4) Attach SFP 5) Power cycle the system. 1) Replace RFU. 1) Check that the code was entered correctly. 2) Call tech support for new license generation.
1) User action.(43) One of the RFU synthesizers is unlocked.(59) (1) Extension or main unit equipment failure (2) Backplane failure(84) (1) One or more components were extracted from the system since trails were defined (2) Radio scripts have been replaced by narrower scripts since trails were defined(107)
(1) One or more components were extracted from the system since trails were defined (2) Radio scripts have been replaced by narrower scripts since trails were defined(107) 1) The kernel (/boot/uImage) is corrupted or missing.(39) RFU Transmitter muted by user.(65) 1) Port is disabled. 2) Line is connected to a disabled port.(37) 1) IDU IP addresses are identical. 2) IDU IP subnets are not identical. 3) Protection Cable is not properly connected. 4) Protection Cable is damaged.(24) Low input to the system.(57) (1) Line is not properly connected (2) Cable is faulty (3) Equipment is faulty (4) STM-1/OC-3 SFP not attached(90) At least one of the PSU voltages is too low.(46) 1) Unit does not match license feature set.(42)