Beruflich Dokumente
Kultur Dokumente
Twist Drills
Twist Drills
Tools with bold feed column no. are preferred choice.
1
0.004 0.006 0.020 0.025 0.032 0.040 0.040 0.050 0.063 0.080 0.080 0.100 0.125 0.160 0.160 0.200 0.250 0.315 0.400
2
0.006 0.008 0.025 0.032 0.040 0.050 0.050 0.063 0.080 0.100 0.100 0.125 0.160 0.200 0.200 0.250 0.310 0.400 0.500
3
0.007 0.012 0.032 0.040 0.050 0.063 0.063 0.080 0.100 0.125 0.125 0.160 0.200 0.250 0.250 0.315 0.400 0.500 0.630
7
0.014 0.020 0.080 0.100 0.125 0.160 0.160 0.200 0.250 0.315 0.315 0.400 0.500 0.630 0.630 0.800 1.000 1.250 1.600
8
0.016 0.023 0.100 0.125 0.160 0.200 0.200 0.250 0.315 0.400 0.400 0.500 0.630 0.800 0.800 1.000 1.250 1.600 1.600
9
0.019 0.025 0.125 0.160 0.160 0.200 0.250 0.315 0.315 0.400 0.500 0.630 0.630 0.800 1.000 1.250 1.250 1.600 2.000
Cooling: without coolant ducts with coolant ducts Coolant: Air Neat oil Soluble oil Cutting direction: right-hand cutting left-hand cutting * Use bright finish drills or use drills with bright polished flutes.
Material group Common structural steels Free-cutting steels Unalloyed heat-treatable steels
Alloyed heat-treatable steels Unalloyed case hardened steels Alloyed case hardened steels Nitriding steels Tool steels High speed steels Spring steels Stainless steels, sulphured austenitic martensitic Hardened steels Special alloys Cast iron Spheroidal graphite iron and malleable cast iron Chilled cast iron Ti and Ti-alloys Aluminium and Al-alloys Al wrought alloys Al cast alloys 10 % Si > 10 % Si Magnesium alloys Copper, low-alloyed Brass, short-chipping long-chipping Bronze, short-chipping Bronze, long-chipping Duroplastics Thermoplastics Kevlar Glass, carbon concent. plastics
Material examples, new description (old description in brackets) Figures in bold = material no. to DIN EN 1.0035 S185(St33),1.0486 P275N(StE285),1.0345 P235GH(H1),1.0425 P265GH(H2) 1.0050 E295 (St50-2), 1.0070 E360 (St70-2), 1.8937 P500NH (WStE500) 1.0718 11SMnPb30 (9SMnPb28), 1.0736 11SMn37 (9SMn36) 1.0727 46S20 (45S20), 1.0728 (60S20), 1.0757 46SPb20 (45SPb20) 1.0402 C22, 1.1178 C30E (Ck30) 1.0503 C45, 1.1191 C45E (Ck45) 1.0601 C60, 1.1221 C60E (Ck60) 1.5131 50MnSi4, 1.7003 38Cr2, 1.7030 28Cr4 1.5710 36NiCr6, 1.7035 41Cr4, 1.7225 42CrMo4 1.0301 (C10), 1.1121 C10E (Ck10) 1.7043 38Cr4 1.5752 15NiCr13 (15NiCr13), 1.7131 16MnCr5, 1.7264 20CrMo5 1.8504 34CrAl6 1.8519 31CrMoV9, 1.8550 34CrAlNi7 1.1750 C75W, 1.2067 102Cr6, 1.2307 29CrMoV9 1.2080 X210Cr12, 1.2083 X42Cr13, 1.2419 105WCr6, 1.2767 X45NiCrMo4 1.3243 S 6-5-2-5, 1.3343 S 6-5-2, 1.3344 S 6-5-3 1.5026 55Si7, 1.7176 55Cr3, 1.8159 51CrV4 (51CrV4) 1.4005 X12CrS13, 1.4104 X14CrMoS17, 1.4105 X6CrMoS17, 1.4305 X8CrNiS18-9 1.4301 X5CrNi18-10 (V2A), 1.4541 X6CrNiTi18-10, 1.4571 X6CrNiMoTi 17-12-2 (V4A) 1.4057 X20CrNi 17 2 (X17CrNi16-2), 1.4122 X39CrMo17-1, 1.4521 X2CrMoTi18-2 Nimonic, Inconel, Monel, Hastelloy 0.6010 EN-GJL-100(GG10), 0.6020 EN-GJL-200(GG20) 0.6025 EN-GJL-250(GG25), 0.6035 EN-GJL-350(GG35) 0.7050 EN-GJS-500-7(GGG50), 0.8035 EN-GJMW-350-4(GTW35) 0.7070 EN-GJS-700-2(GGG70), 0.8170 EN-GJMB-700-2(GTS70) 3.7024 Ti99,5, 3.7114 TiAl5Sn2,5, 3.7124 TiCu2 3.7154 TiAl6Zr5, 3.7165 TiAl6V4, 3.7184 TiAl4Mo4Sn2,5, - TiAl8Mo1V1 3.0255 Al99,5, 3.2315 AlMgSi1, 3.3515 AlMg1 3.0615 AlMgSiPb, 3.1325 AlCuMg1, 3.3245 AlMg3Si, 3.4365 AlZnMgCu1,5 3.2131 G-AlSi5Cu1, 3.2153 G-AlSi7Cu3, 3.2573 G-AlSi9 3.2581 G-AlSi12, 3.2583 G-AlSi12Cu, - G-AlSi12CuNiMg 3.5200 MgMn2, 3.5812.05 G-MgAl8Zn1, 3.5612.05 G-MgAl6Zn1 2.0070 SE-Cu, 2.1020 CuSn6, 2.1096 G-CuSn5ZnPb 2.0380 CuZn39Pb2, 2.0401 CuZn39Pb3, 2.0410 CuZn43Pb2 2.0250 CuZn20, 2.0280 CuZn33, 2.0332 CuZn37Pb0,5 2.1090 CuSn7ZnPb, 2.1170 CuPb5Sn5, 2.1176 CuPb10Sn 2.0790 CuNi18Zn19Pb 2.0916 CuAl5, 2.0960 CuAl9Mn, 2.1050 CuSn10 2.0980 CuAl11Ni, 2.1247 CuBe2 Bakelit, Resopal, Pertinax, Moltopren Plexiglass, Hostalen, Novodur, Makralon Kevlar GFK/CFK
Tensile strength Hardness MPa (N/mm2) 500 >500-850 850 850-1000 700 700-850 850-1000 850-1000 1000-1200 750 850-1000 1000-1200 850-1000 >1000-1200 850 >850-1000 650-1000 330 HB 850 850 850 40-48 HRC >48-60 HRC 1200 240 HB <300 HB 240 HB <300 HB 350 HB 850 >850-1200 400 450 600 600 450 400 600 600 600 >600-850 850 >850-1000
Coolant
bright
steam tempered
nitrided lands
nitrided
golden brown
TiAlN
52
GUHRINGGUIDE
Tool material Type Surface finish Guh. no. straight shank DIN 1897 G.S.
HSS
HSS
N 653 672 N 2460 GV 120 329 330
HSCO
VA 1261 128 132 363 1263
279 431 343 344
M42
N N 1259 129 136
314
N 223 226
H 224 227
W 225 228
GT 80 552 553
278
278
278
278
279
279
279
431
vc m/min 36 28 36 28 36 28
vc vc m/min m/min 6 5 5 45 36 45 36 45 32 18 22 45 20 18 59 47 59 47 59 42 23 29 59 26 23 29
vc m/min
6 5 5 5
6 5
6 5 5
6 5 6 5 5
4 4 6 4 4 4 5
7 6 7 6 6
5 5 6
30 30 22 20 16 18 14 16 12 20 12 12 10 16 12 14 4 8 40 30 36 28 10 12 8 100 100 80 60 40 50 40 36 30 25 20
5 4 4 3 4 3 4 3 4 3 3 2 3
1 6 6 3 2 2 4 3 5
4
4 3 4 3 4 3 4 3 3 2 4 3 3 1 3 3 3 3 3 3 3
36
7
5 5 5
18
22
4 3
1 1
36 28 32 23
6 6
6 6
6 6 6 6
45 36 40 28
59 47 53 36
6 6
6 6
7 7
7
6 6
2 7 7 7 6 5 5
90 90 70 55 90 36 70 45 36 32 28 18 28
7* 6* 6* 5* 5* 4* 4* 4* 4 5*
7 7
7
6 6
4
7 6 5 5 4
4 4 6
7 7
2 2
90 80 45 55 45 40 35 28 22 36
117 104 59 72 59 52 46 36 29 47
7 6 5 5 4 4 4 5
4 4
8 7 6 6 5 5 5
6 5 5
5 5
4
4 4 4
4 5
4
5
4 4
AlTiN
TiCN
FIRE
AlCrN
TiN
MolyGlide
53
Twist Drills
3D drilling depth
Twist Drills
Tools with bold feed column no. are preferred choice.
1
0.004 0.006 0.020 0.025 0.032 0.040 0.040 0.050 0.063 0.080 0.080 0.100 0.125 0.160 0.160 0.200 0.250 0.315 0.400
2
0.006 0.008 0.025 0.032 0.040 0.050 0.050 0.063 0.080 0.100 0.100 0.125 0.160 0.200 0.200 0.250 0.310 0.400 0.500
3
0.007 0.012 0.032 0.040 0.050 0.063 0.063 0.080 0.100 0.125 0.125 0.160 0.200 0.250 0.250 0.315 0.400 0.500 0.630
7
0.014 0.020 0.080 0.100 0.125 0.160 0.160 0.200 0.250 0.315 0.315 0.400 0.500 0.630 0.630 0.800 1.000 1.250 1.600
8
0.016 0.023 0.100 0.125 0.160 0.200 0.200 0.250 0.315 0.400 0.400 0.500 0.630 0.800 0.800 1.000 1.250 1.600 1.600
9
0.019 0.025 0.125 0.160 0.160 0.200 0.250 0.315 0.315 0.400 0.500 0.630 0.630 0.800 1.000 1.250 1.250 1.600 2.000
Cooling: without coolant ducts with coolant ducts Coolant: Air Neat oil Soluble oil Cutting direction: right-hand cutting left-hand cutting
Material group Common structural steels Free-cutting steels Unalloyed heat-treatable steels
Alloyed heat-treatable steels Unalloyed case hardened steels Alloyed case hardened steels Nitriding steels Tool steels High speed steels Spring steels Stainless steels, sulphured austenitic martensitic Hardened steels Special alloys Cast iron Spheroidal graphite iron and malleable cast iron Chilled cast iron Ti and Ti-alloys Aluminium and Al-alloys Al wrought alloys Al cast alloys 10 % Si > 10 % Si Magnesium alloys Copper, low-alloyed Brass, short-chipping long-chipping Bronze, short-chipping Bronze, long-chipping Duroplastics Thermoplastics Kevlar Glass, carbon concent. plastics
Material examples, new description (old description in brackets) Figures in bold = material no. to DIN EN 1.0035 S185(St33),1.0486 P275N(StE285),1.0345 P235GH(H1),1.0425 P265GH(H2) 1.0050 E295 (St50-2), 1.0070 E360 (St70-2), 1.8937 P500NH (WStE500) 1.0718 11SMnPb30 (9SMnPb28), 1.0736 11SMn37 (9SMn36) 1.0727 46S20 (45S20), 1.0728 (60S20), 1.0757 46SPb20 (45SPb20) 1.0402 C22, 1.1178 C30E (Ck30) 1.0503 C45, 1.1191 C45E (Ck45) 1.0601 C60, 1.1221 C60E (Ck60) 1.5131 50MnSi4, 1.7003 38Cr2, 1.7030 28Cr4 1.5710 36NiCr6, 1.7035 41Cr4, 1.7225 42CrMo4 1.0301 (C10), 1.1121 C10E (Ck10) 1.7043 38Cr4 1.5752 15NiCr13 (15NiCr13), 1.7131 16MnCr5, 1.7264 20CrMo5 1.8504 34CrAl6 1.8519 31CrMoV9, 1.8550 34CrAlNi7 1.1750 C75W, 1.2067 102Cr6, 1.2307 29CrMoV9 1.2080 X210Cr12, 1.2083 X42Cr13, 1.2419 105WCr6, 1.2767 X45NiCrMo4 1.3243 S 6-5-2-5, 1.3343 S 6-5-2, 1.3344 S 6-5-3 1.5026 55Si7, 1.7176 55Cr3, 1.8159 51CrV4 (51CrV4) 1.4005 X12CrS13, 1.4104 X14CrMoS17, 1.4105 X6CrMoS17, 1.4305 X8CrNiS18-9 1.4301 X5CrNi18-10 (V2A), 1.4541 X6CrNiTi18-10, 1.4571 X6CrNiMoTi 17-12-2 (V4A) 1.4057 X20CrNi 17 2 (X17CrNi16-2), 1.4122 X39CrMo17-1, 1.4521 X2CrMoTi18-2 Nimonic, Inconel, Monel, Hastelloy 0.6010 EN-GJL-100(GG10), 0.6020 EN-GJL-200(GG20) 0.6025 EN-GJL-250(GG25), 0.6035 EN-GJL-350(GG35) 0.7050 EN-GJS-500-7(GGG50), 0.8035 EN-GJMW-350-4(GTW35) 0.7070 EN-GJS-700-2(GGG70), 0.8170 EN-GJMB-700-2(GTS70) 3.7024 Ti99,5, 3.7114 TiAl5Sn2,5, 3.7124 TiCu2 3.7154 TiAl6Zr5, 3.7165 TiAl6V4, 3.7184 TiAl4Mo4Sn2,5, - TiAl8Mo1V1 3.0255 Al99,5, 3.2315 AlMgSi1, 3.3515 AlMg1 3.0615 AlMgSiPb, 3.1325 AlCuMg1, 3.3245 AlMg3Si, 3.4365 AlZnMgCu1,5 3.2131 G-AlSi5Cu1, 3.2153 G-AlSi7Cu3, 3.2573 G-AlSi9 3.2581 G-AlSi12, 3.2583 G-AlSi12Cu, - G-AlSi12CuNiMg 3.5200 MgMn2, 3.5812.05 G-MgAl8Zn1, 3.5612.05 G-MgAl6Zn1 2.0070 SE-Cu, 2.1020 CuSn6, 2.1096 G-CuSn5ZnPb 2.0380 CuZn39Pb2, 2.0401 CuZn39Pb3, 2.0410 CuZn43Pb2 2.0250 CuZn20, 2.0280 CuZn33, 2.0332 CuZn37Pb0,5 2.1090 CuSn7ZnPb, 2.1170 CuPb5Sn5, 2.1176 CuPb10Sn 2.0790 CuNi18Zn19Pb 2.0916 CuAl5, 2.0960 CuAl9Mn, 2.1050 CuSn10 2.0980 CuAl11Ni, 2.1247 CuBe2 Bakelit, Resopal, Pertinax, Moltopren Plexiglass, Hostalen, Novodur, Makralon Kevlar GFK/CFK
Tensile strength Hardness MPa (N/mm2) 500 >500-850 850 850-1000 700 700-850 850-1000 850-1000 1000-1200 750 850-1000 1000-1200 850-1000 >1000-1200 850 >850-1000 650-1000 330 HB 850 850 850 40-48 HRC >48-60 HRC 1200 240 HB <300 HB 240 HB <300 HB 350 HB 850 >850-1200 400 450 600 600 450 400 600 600 600 >600-850 850 >850-1000
Coolant
bright
steam tempered
nitrided lands
nitrided
golden brown
TiAlN
54
GUHRINGGUIDE
Tool material Type Surface finish DIN 1897 G.S. MT G.S. Std. range page
HSCO
P2000 2048
HSCO
GT 80
HSCO
GV 120
HSCO
GU 500
PM HSS-E
GT 500 515
Guh. no.
straight shank
1228
2498
659
279
279
279
279
279
431
329
314
vc m/min 34 27 34 30 34 30 22 20 16 34 18 14 16 12 18 12 12 10 16 12 14
vc vc m/min m/min 40 32 45 40 42 40 28 25 20 40 22 18 20 15 25 15 15 12 15 10 12 50 40 60 52 50 45 32 32 26 48 29 23 26 20 28 19 19 16 18 12 15
vc vc m/min m/min
vc m/min 45 35 50 40 42 35 22 18 15 40 20 15 18 12 18 13 13 18 12 15
vc m/min 50 40 60 52 50 45 32 32 28 48 28 23 25 20 28 20 20 16 18 12 15
6 5 6 5 5 5 4 4 6
4 3 4 3 4 3 3 2 4 3 3 3
6 5
6 5 4 4 3 4 4 3 4 3 4 3 3 2 3 3
7 6
6 6 5 5 4 4 5 4 5 4 5 4 4 3 3 3
40 40 28 25 20 22 18 20 15 25 15 15 12 20 15 18 5 10 50 40 45 32 12 15 10
52 52 36 32 26 29 23 26 19 22 19 19 16 26 19 23 7 13 65 52 59 42 16 19 13
5 5
6 6
5 5
4 4 3 4 3 4 3 4 3 3 2 3 3
1 1 6 4
5 5 4 5 4 5 4 5 4 4 3 4 4
2 2 7 5
4 4 3 4 3 4 3 4 3 3 2 3 3
1 1 6 4
6 5 6 6 6 6 5 6
4 3 4 3 4 3 3 4 3
5 3 5 4 5 4 5 4 4 2
4 3 3
4 4 4
8 38 30 32 24 10
2 6 6 6 6 3
50 40 45 32 8
65 52 59 42 10
6 6 6 6
3
7 7 7 7
4
6
6 6 3 2 2
7
7 7 4 3 3
6
6 6 3 2 2
45 36 40 28
6 6 6 6
65 52 60 42 10
7 7 7 7
4
100 100 75 60 85 40 68 44 40 30 28 26 25 22
7 7 7 6 6 5 5 5 4 4 4 4 4 5
50 60 50 45 40 32 25
65 78 60 59 52 42 28
5 5 5 4 4 4
6 6 5 5 5 5
50 45 40 32
60 59 52 42
4 4
4
5 5
5
4 4
4
70 70 85 70 70 32 63 40 50 35 32 28 25 15
7 7 7 6 5 5 5 4 4 4 4 4 4
6
90 80 65 78 60 59 52 42 28
7 6 5 6 5 5 5 5
AlTiN
TiCN
FIRE
AlCrN
TiN
MolyGlide
55
Twist Drills
3D drilling depth
Twist Drills
Tools with bold feed column no. are preferred choice.
1
0.004 0.006 0.020 0.025 0.032 0.040 0.040 0.050 0.063 0.080 0.080 0.100 0.125 0.160 0.160 0.200 0.250 0.315 0.400
2
0.006 0.008 0.025 0.032 0.040 0.050 0.050 0.063 0.080 0.100 0.100 0.125 0.160 0.200 0.200 0.250 0.310 0.400 0.500
3
0.007 0.012 0.032 0.040 0.050 0.063 0.063 0.080 0.100 0.125 0.125 0.160 0.200 0.250 0.250 0.315 0.400 0.500 0.630
7
0.014 0.020 0.080 0.100 0.125 0.160 0.160 0.200 0.250 0.315 0.315 0.400 0.500 0.630 0.630 0.800 1.000 1.250 1.600
8
0.016 0.023 0.100 0.125 0.160 0.200 0.200 0.250 0.315 0.400 0.400 0.500 0.630 0.800 0.800 1.000 1.250 1.600 1.600
9
0.019 0.025 0.125 0.160 0.160 0.200 0.250 0.315 0.315 0.400 0.500 0.630 0.630 0.800 1.000 1.250 1.250 1.600 2.000
Cooling: without coolant ducts with coolant ducts Coolant: Air Neat oil Soluble oil Cutting direction: right-hand cutting left-hand cutting * Cutting lip corrected to appr. 10
Material group Common structural steels Free-cutting steels Unalloyed heat-treatable steels
Alloyed heat-treatable steels Unalloyed case hardened steels Alloyed case hardened steels Nitriding steels Tool steels High speed steels Spring steels Stainless steels, sulphured austenitic martensitic Hardened steels Special alloys Cast iron Spheroidal graphite iron and malleable cast iron Chilled cast iron Ti and Ti-alloys Aluminium and Al-alloys Al wrought alloys Al cast alloys 10 % Si > 10 % Si Magnesium alloys Copper, low-alloyed Brass, short-chipping long-chipping Bronze, short-chipping Bronze, long-chipping Duroplastics Thermoplastics Kevlar Glass, carbon concent. plastics
Material examples, new description (old description in brackets) Figures in bold = material no. to DIN EN 1.0035 S185(St33),1.0486 P275N(StE285),1.0345 P235GH(H1),1.0425 P265GH(H2) 1.0050 E295 (St50-2), 1.0070 E360 (St70-2), 1.8937 P500NH (WStE500) 1.0718 11SMnPb30 (9SMnPb28), 1.0736 11SMn37 (9SMn36) 1.0727 46S20 (45S20), 1.0728 (60S20), 1.0757 46SPb20 (45SPb20) 1.0402 C22, 1.1178 C30E (Ck30) 1.0503 C45, 1.1191 C45E (Ck45) 1.0601 C60, 1.1221 C60E (Ck60) 1.5131 50MnSi4, 1.7003 38Cr2, 1.7030 28Cr4 1.5710 36NiCr6, 1.7035 41Cr4, 1.7225 42CrMo4 1.0301 (C10), 1.1121 C10E (Ck10) 1.7043 38Cr4 1.5752 15NiCr13 (15NiCr13), 1.7131 16MnCr5, 1.7264 20CrMo5 1.8504 34CrAl6 1.8519 31CrMoV9, 1.8550 34CrAlNi7 1.1750 C75W, 1.2067 102Cr6, 1.2307 29CrMoV9 1.2080 X210Cr12, 1.2083 X42Cr13, 1.2419 105WCr6, 1.2767 X45NiCrMo4 1.3243 S 6-5-2-5, 1.3343 S 6-5-2, 1.3344 S 6-5-3 1.5026 55Si7, 1.7176 55Cr3, 1.8159 51CrV4 (51CrV4) 1.4005 X12CrS13, 1.4104 X14CrMoS17, 1.4105 X6CrMoS17, 1.4305 X8CrNiS18-9 1.4301 X5CrNi18-10 (V2A), 1.4541 X6CrNiTi18-10, 1.4571 X6CrNiMoTi 17-12-2 (V4A) 1.4057 X20CrNi 17 2 (X17CrNi16-2), 1.4122 X39CrMo17-1, 1.4521 X2CrMoTi18-2 Nimonic, Inconel, Monel, Hastelloy 0.6010 EN-GJL-100(GG10), 0.6020 EN-GJL-200(GG20) 0.6025 EN-GJL-250(GG25), 0.6035 EN-GJL-350(GG35) 0.7050 EN-GJS-500-7(GGG50), 0.8035 EN-GJMW-350-4(GTW35) 0.7070 EN-GJS-700-2(GGG70), 0.8170 EN-GJMB-700-2(GTS70) 3.7024 Ti99,5, 3.7114 TiAl5Sn2,5, 3.7124 TiCu2 3.7154 TiAl6Zr5, 3.7165 TiAl6V4, 3.7184 TiAl4Mo4Sn2,5, - TiAl8Mo1V1 3.0255 Al99,5, 3.2315 AlMgSi1, 3.3515 AlMg1 3.0615 AlMgSiPb, 3.1325 AlCuMg1, 3.3245 AlMg3Si, 3.4365 AlZnMgCu1,5 3.2131 G-AlSi5Cu1, 3.2153 G-AlSi7Cu3, 3.2573 G-AlSi9 3.2581 G-AlSi12, 3.2583 G-AlSi12Cu, - G-AlSi12CuNiMg 3.5200 MgMn2, 3.5812.05 G-MgAl8Zn1, 3.5612.05 G-MgAl6Zn1 2.0070 SE-Cu, 2.1020 CuSn6, 2.1096 G-CuSn5ZnPb 2.0380 CuZn39Pb2, 2.0401 CuZn39Pb3, 2.0410 CuZn43Pb2 2.0250 CuZn20, 2.0280 CuZn33, 2.0332 CuZn37Pb0,5 2.1090 CuSn7ZnPb, 2.1170 CuPb5Sn5, 2.1176 CuPb10Sn 2.0790 CuNi18Zn19Pb 2.0916 CuAl5, 2.0960 CuAl9Mn, 2.1050 CuSn10 2.0980 CuAl11Ni, 2.1247 CuBe2 Bakelit, Resopal, Pertinax, Moltopren Plexiglass, Hostalen, Novodur, Makralon Kevlar GFK/CFK
Tensile strength Hardness MPa (N/mm2) 500 >500-850 850 850-1000 700 700-850 850-1000 850-1000 1000-1200 750 850-1000 1000-1200 850-1000 >1000-1200 850 >850-1000 650-1000 330 HB 850 850 850 40-48 HRC >48-60 HRC 1200 240 HB <300 HB 240 HB <300 HB 350 HB 850 >850-1200 400 450 600 600 450 400 600 600 600 >600-850 850 >850-1000
Coolant
bright
steam tempered
nitrided lands
nitrided
golden brown
TiAlN
56
GUHRINGGUIDE
Tool material Carbide grade Type Surface finish DIN 6537 DIN 6539 DIN 8037 DIN 8038 G.S. MT DIN 8041 Std. range page
Carbide
K10/K20 N
Carbide-tipped
K10/K20 N K10/K20 N K10/K20 N
Carbide
K10/K20 N
Carbide
K H 1946
K10/K20 N
K10/K20 N/FK
Guh. no.
straight shank
2463
1149
428
710 705
251 424 491 424
707
429 314 341
vc m/min 80 70 80 70 80 70 60 60 80 60 50 50 4 4
vc m/min
5 4
4 4 4 4 5 4 4 3
4 3
6 5
5 5 5 5 6 5 65 5 80 4 4 4
80
25 25 25 25 20 10 15 90 80 80 70 10 20 15 200 200 150 120 180 80 180 180 120 120 70 50 50 40 150 80
2 4 3 3 3 2
3 2 4 4 4 4
5 4 4 4 5 5 5 5
4 3 3
40 30 90 80 80 70 30
2 1
8 8 8 7 2
4 4 4 4
3 2
1 26 20 260 260 195 156 234 104 234 234 156 156 91 65 65 52 104
5* 5 5 4 3 4 3 3
7 7 6 6 5 5 5*
8 8 7 6 6 6 6 6 6
5 4 5 4 4 7
5 5
4 3 3
TiCN
1
FIRE AlCrN
3 2
AlTiN
TiN
MolyGlide
57
Twist Drills
3D drilling depth
Twist Drills
Tools with bold feed column no. are preferred choice.
1
0.004 0.006 0.020 0.025 0.032 0.040 0.040 0.050 0.063 0.080 0.080 0.100 0.125 0.160 0.160 0.200 0.250 0.315 0.400
2
0.006 0.008 0.025 0.032 0.040 0.050 0.050 0.063 0.080 0.100 0.100 0.125 0.160 0.200 0.200 0.250 0.310 0.400 0.500
3
0.007 0.012 0.032 0.040 0.050 0.063 0.063 0.080 0.100 0.125 0.125 0.160 0.200 0.250 0.250 0.315 0.400 0.500 0.630
7
0.014 0.020 0.080 0.100 0.125 0.160 0.160 0.200 0.250 0.315 0.315 0.400 0.500 0.630 0.630 0.800 1.000 1.250 1.600
8
0.016 0.023 0.100 0.125 0.160 0.200 0.200 0.250 0.315 0.400 0.400 0.500 0.630 0.800 0.800 1.000 1.250 1.600 1.600
9
0.019 0.025 0.125 0.160 0.160 0.200 0.250 0.315 0.315 0.400 0.500 0.630 0.630 0.800 1.000 1.250 1.250 1.600 2.000
Cooling: without coolant ducts with coolant ducts Coolant: Air Neat oil Soluble oil Cutting direction: right-hand cutting left-hand cutting * Use bright finish drills or use drills with bright polished flutes.
Material group Common structural steels Free-cutting steels Unalloyed heat-treatable steels
Alloyed heat-treatable steels Unalloyed case hardened steels Alloyed case hardened steels Nitriding steels Tool steels High speed steels Spring steels Stainless steels, sulphured austenitic martensitic Hardened steels Special alloys Cast iron Spheroidal graphite iron and malleable cast iron Chilled cast iron Ti and Ti-alloys Aluminium and Al-alloys Al wrought alloys Al cast alloys 10 % Si > 10 % Si Magnesium alloys Copper, low-alloyed Brass, short-chipping long-chipping Bronze, short-chipping Bronze, long-chipping Duroplastics Thermoplastics Kevlar Glass, carbon concent. plastics
Material examples, new description (old description in brackets) Figures in bold = material no. to DIN EN 1.0035 S185(St33),1.0486 P275N(StE285),1.0345 P235GH(H1),1.0425 P265GH(H2) 1.0050 E295 (St50-2), 1.0070 E360 (St70-2), 1.8937 P500NH (WStE500) 1.0718 11SMnPb30 (9SMnPb28), 1.0736 11SMn37 (9SMn36) 1.0727 46S20 (45S20), 1.0728 (60S20), 1.0757 46SPb20 (45SPb20) 1.0402 C22, 1.1178 C30E (Ck30) 1.0503 C45, 1.1191 C45E (Ck45) 1.0601 C60, 1.1221 C60E (Ck60) 1.5131 50MnSi4, 1.7003 38Cr2, 1.7030 28Cr4 1.5710 36NiCr6, 1.7035 41Cr4, 1.7225 42CrMo4 1.0301 (C10), 1.1121 C10E (Ck10) 1.7043 38Cr4 1.5752 15NiCr13 (15NiCr13), 1.7131 16MnCr5, 1.7264 20CrMo5 1.8504 34CrAl6 1.8519 31CrMoV9, 1.8550 34CrAlNi7 1.1750 C75W, 1.2067 102Cr6, 1.2307 29CrMoV9 1.2080 X210Cr12, 1.2083 X42Cr13, 1.2419 105WCr6, 1.2767 X45NiCrMo4 1.3243 S 6-5-2-5, 1.3343 S 6-5-2, 1.3344 S 6-5-3 1.5026 55Si7, 1.7176 55Cr3, 1.8159 51CrV4 (51CrV4) 1.4005 X12CrS13, 1.4104 X14CrMoS17, 1.4105 X6CrMoS17, 1.4305 X8CrNiS18-9 1.4301 X5CrNi18-10 (V2A), 1.4541 X6CrNiTi18-10, 1.4571 X6CrNiMoTi 17-12-2 (V4A) 1.4057 X20CrNi 17 2 (X17CrNi16-2), 1.4122 X39CrMo17-1, 1.4521 X2CrMoTi18-2 Nimonic, Inconel, Monel, Hastelloy 0.6010 EN-GJL-100(GG10), 0.6020 EN-GJL-200(GG20) 0.6025 EN-GJL-250(GG25), 0.6035 EN-GJL-350(GG35) 0.7050 EN-GJS-500-7(GGG50), 0.8035 EN-GJMW-350-4(GTW35) 0.7070 EN-GJS-700-2(GGG70), 0.8170 EN-GJMB-700-2(GTS70) 3.7024 Ti99,5, 3.7114 TiAl5Sn2,5, 3.7124 TiCu2 3.7154 TiAl6Zr5, 3.7165 TiAl6V4, 3.7184 TiAl4Mo4Sn2,5, - TiAl8Mo1V1 3.0255 Al99,5, 3.2315 AlMgSi1, 3.3515 AlMg1 3.0615 AlMgSiPb, 3.1325 AlCuMg1, 3.3245 AlMg3Si, 3.4365 AlZnMgCu1,5 3.2131 G-AlSi5Cu1, 3.2153 G-AlSi7Cu3, 3.2573 G-AlSi9 3.2581 G-AlSi12, 3.2583 G-AlSi12Cu, - G-AlSi12CuNiMg 3.5200 MgMn2, 3.5812.05 G-MgAl8Zn1, 3.5612.05 G-MgAl6Zn1 2.0070 SE-Cu, 2.1020 CuSn6, 2.1096 G-CuSn5ZnPb 2.0380 CuZn39Pb2, 2.0401 CuZn39Pb3, 2.0410 CuZn43Pb2 2.0250 CuZn20, 2.0280 CuZn33, 2.0332 CuZn37Pb0,5 2.1090 CuSn7ZnPb, 2.1170 CuPb5Sn5, 2.1176 CuPb10Sn 2.0790 CuNi18Zn19Pb 2.0916 CuAl5, 2.0960 CuAl9Mn, 2.1050 CuSn10 2.0980 CuAl11Ni, 2.1247 CuBe2 Bakelit, Resopal, Pertinax, Moltopren Plexiglass, Hostalen, Novodur, Makralon Kevlar GFK/CFK
Tensile strength Hardness MPa (N/mm2) 500 >500-850 850 850-1000 700 700-850 850-1000 850-1000 1000-1200 750 850-1000 1000-1200 850-1000 >1000-1200 850 >850-1000 650-1000 330 HB 850 850 850 40-48 HRC >48-60 HRC 1200 240 HB <300 HB 240 HB <300 HB 350 HB 850 >850-1200 400 450 600 600 450 400 600 600 600 >600-850 850 >850-1000
Coolant
bright
steam tempered
nitrided lands
nitrided
golden brown
TiAlN
58
GUHRINGGUIDE
Tool material Type Surface finish Guh. no. Morse straight taper shank DIN 338 G.S. DIN 345
HSS
H 206 209 207 210 246 251 460 247 W GT 100 549 550 558
208
229 245 592
248
208 207 207 342 434 434 434 207 434 207 434 208 434
vc m/min 32 25 32 25 32 25 6 5 6 5 5 5
6 5
5 5
6 5
6 5
5 5
6 5
6 5
5 5
6 5
6 5
5 5
6 5
6
5 5 5
6 5
32
16
32 25 28 20
6 6 6 6
6 6
6 6
6 6
6 6
6 6
6 6
6 6
6 6
6 6 6 6
80 80 63 50 80 32 63 40 32 25 16 25
7 6
6 5 5 4 4 4 4 5
7* 6* 6* 5* 5* 4* 4* 4* 4 5*
7* 6* 6* 5* 5* 4* 4* 4* 4 5*
7* 6* 6* 5* 5* 4* 4* 4* 4 5*
7* 6* 6* 5* 5* 4* 4* 4* 4 5*
7 7
7
6 6
4
7 6 5 5
4 6
7 7
AlTiN
TiCN
FIRE
AlCrN
TiN
MolyGlide
59
Twist Drills
5D drilling depth
Twist Drills
Tools with bold feed column no. are preferred choice.
1
0.004 0.006 0.020 0.025 0.032 0.040 0.040 0.050 0.063 0.080 0.080 0.100 0.125 0.160 0.160 0.200 0.250 0.315 0.400
2
0.006 0.008 0.025 0.032 0.040 0.050 0.050 0.063 0.080 0.100 0.100 0.125 0.160 0.200 0.200 0.250 0.310 0.400 0.500
3
0.007 0.012 0.032 0.040 0.050 0.063 0.063 0.080 0.100 0.125 0.125 0.160 0.200 0.250 0.250 0.315 0.400 0.500 0.630
7
0.014 0.020 0.080 0.100 0.125 0.160 0.160 0.200 0.250 0.315 0.315 0.400 0.500 0.630 0.630 0.800 1.000 1.250 1.600
8
0.016 0.023 0.100 0.125 0.160 0.200 0.200 0.250 0.315 0.400 0.400 0.500 0.630 0.800 0.800 1.000 1.250 1.600 1.600
9
0.019 0.025 0.125 0.160 0.160 0.200 0.250 0.315 0.315 0.400 0.500 0.630 0.630 0.800 1.000 1.250 1.250 1.600 2.000
Cooling: without coolant ducts with coolant ducts Coolant: Air Neat oil Soluble oil Cutting direction: right-hand cutting left-hand cutting * Use bright finish drills or use drills with bright polished flutes.
Material group Common structural steels Free-cutting steels Unalloyed heat-treatable steels
Alloyed heat-treatable steels Unalloyed case hardened steels Alloyed case hardened steels Nitriding steels Tool steels High speed steels Spring steels Stainless steels, sulphured austenitic martensitic Hardened steels Special alloys Cast iron Spheroidal graphite iron and malleable cast iron Chilled cast iron Ti and Ti-alloys Aluminium and Al-alloys Al wrought alloys Al cast alloys 10 % Si > 10 % Si Magnesium alloys Copper, low-alloyed Brass, short-chipping long-chipping Bronze, short-chipping Bronze, long-chipping Duroplastics Thermoplastics Kevlar Glass, carbon concent. plastics
Material examples, new description (old description in brackets) Figures in bold = material no. to DIN EN 1.0035 S185(St33),1.0486 P275N(StE285),1.0345 P235GH(H1),1.0425 P265GH(H2) 1.0050 E295 (St50-2), 1.0070 E360 (St70-2), 1.8937 P500NH (WStE500) 1.0718 11SMnPb30 (9SMnPb28), 1.0736 11SMn37 (9SMn36) 1.0727 46S20 (45S20), 1.0728 (60S20), 1.0757 46SPb20 (45SPb20) 1.0402 C22, 1.1178 C30E (Ck30) 1.0503 C45, 1.1191 C45E (Ck45) 1.0601 C60, 1.1221 C60E (Ck60) 1.5131 50MnSi4, 1.7003 38Cr2, 1.7030 28Cr4 1.5710 36NiCr6, 1.7035 41Cr4, 1.7225 42CrMo4 1.0301 (C10), 1.1121 C10E (Ck10) 1.7043 38Cr4 1.5752 15NiCr13 (15NiCr13), 1.7131 16MnCr5, 1.7264 20CrMo5 1.8504 34CrAl6 1.8519 31CrMoV9, 1.8550 34CrAlNi7 1.1750 C75W, 1.2067 102Cr6, 1.2307 29CrMoV9 1.2080 X210Cr12, 1.2083 X42Cr13, 1.2419 105WCr6, 1.2767 X45NiCrMo4 1.3243 S 6-5-2-5, 1.3343 S 6-5-2, 1.3344 S 6-5-3 1.5026 55Si7, 1.7176 55Cr3, 1.8159 51CrV4 (51CrV4) 1.4005 X12CrS13, 1.4104 X14CrMoS17, 1.4105 X6CrMoS17, 1.4305 X8CrNiS18-9 1.4301 X5CrNi18-10 (V2A), 1.4541 X6CrNiTi18-10, 1.4571 X6CrNiMoTi 17-12-2 (V4A) 1.4057 X20CrNi 17 2 (X17CrNi16-2), 1.4122 X39CrMo17-1, 1.4521 X2CrMoTi18-2 Nimonic, Inconel, Monel, Hastelloy 0.6010 EN-GJL-100(GG10), 0.6020 EN-GJL-200(GG20) 0.6025 EN-GJL-250(GG25), 0.6035 EN-GJL-350(GG35) 0.7050 EN-GJS-500-7(GGG50), 0.8035 EN-GJMW-350-4(GTW35) 0.7070 EN-GJS-700-2(GGG70), 0.8170 EN-GJMB-700-2(GTS70) 3.7024 Ti99,5, 3.7114 TiAl5Sn2,5, 3.7124 TiCu2 3.7154 TiAl6Zr5, 3.7165 TiAl6V4, 3.7184 TiAl4Mo4Sn2,5, - TiAl8Mo1V1 3.0255 Al99,5, 3.2315 AlMgSi1, 3.3515 AlMg1 3.0615 AlMgSiPb, 3.1325 AlCuMg1, 3.3245 AlMg3Si, 3.4365 AlZnMgCu1,5 3.2131 G-AlSi5Cu1, 3.2153 G-AlSi7Cu3, 3.2573 G-AlSi9 3.2581 G-AlSi12, 3.2583 G-AlSi12Cu, - G-AlSi12CuNiMg 3.5200 MgMn2, 3.5812.05 G-MgAl8Zn1, 3.5612.05 G-MgAl6Zn1 2.0070 SE-Cu, 2.1020 CuSn6, 2.1096 G-CuSn5ZnPb 2.0380 CuZn39Pb2, 2.0401 CuZn39Pb3, 2.0410 CuZn43Pb2 2.0250 CuZn20, 2.0280 CuZn33, 2.0332 CuZn37Pb0,5 2.1090 CuSn7ZnPb, 2.1170 CuPb5Sn5, 2.1176 CuPb10Sn 2.0790 CuNi18Zn19Pb 2.0916 CuAl5, 2.0960 CuAl9Mn, 2.1050 CuSn10 2.0980 CuAl11Ni, 2.1247 CuBe2 Bakelit, Resopal, Pertinax, Moltopren Plexiglass, Hostalen, Novodur, Makralon Kevlar GFK/CFK
Tensile strength Hardness MPa (N/mm2) 500 >500-850 850 850-1000 700 700-850 850-1000 850-1000 1000-1200 750 850-1000 1000-1200 850-1000 >1000-1200 850 >850-1000 650-1000 330 HB 850 850 850 40-48 HRC >48-60 HRC 1200 240 HB <300 HB 240 HB <300 HB 350 HB 850 >850-1200 400 450 600 600 450 400 600 600 600 >600-850 850 >850-1000
Coolant
bright
steam tempered
nitrided lands
nitrided
golden brown
TiAlN
60
GUHRINGGUIDE
HSS
HSCO
N 2457 305 308 345 208 250 435 351 460 250 GT 100 622 645 435 250 251 Ti 605 608 1260 1262 435 VA
M42
N 1146
N 651 664 654 208 435 208 208 2456 652 665
GT 100
Guh. no.
DIN 338
CM
606 435
251
vc vc m/min m/min 40 32 40 32 40 32 16 20 40 18 15 20 52 40 52 40 52 40 20 26 52 23 20 26
vc m/min 6 5 5 5 5 4 4 6 4 4 4 7 6 7 6 6 6 5 5 7 5 5 5
6 5 5 5
4 4 6 5
7 6 6 6
5 5 7 6
28 28 15 18 14 16 12 14 10 18 10 10 8 14 10 12 3 6 36 28 30 22 8 10 6 90 90 70 55 36 45 36 30 28 22 18
5 5
5
5 4
4 4
3
6
4 4 4
7
5 5 5
4 3 3 3 3 3 4
3 4 4 4
4 4 4
3 3 2 4 3 3 3 3
3 3 3 3 4
3 3 3 3
2 3 3
1
4
3 3
2
3
1 1
40 30 35 25
52 52 47 32
6 6
6 6
7 7 7 7
6 6 6 6
7 7 7 7
6 6
3 6
6 6 6 6 3
2 2
3
2
80 70 100 40 50 40 36 32 25 20 32
105 91 130 52 65 52 47 40 32 26
6
6 5 5
8 8
7 6 6
7 6
5 5
4 4
8 7 7 6
7 6 5* 5* 4* 4* 4* 4* 4 5 4
7 7
7 6
5 5
4 4 4 4
4 5
5 5 5 5
5
6
5 5 5
4
4
4 1
AlTiN
TiCN
FIRE
AlCrN
TiN
MolyGlide
61
Twist Drills
5D drilling depth
Twist Drills
Tools with bold feed column no. are preferred choice.
1
0.004 0.006 0.020 0.025 0.032 0.040 0.040 0.050 0.063 0.080 0.080 0.100 0.125 0.160 0.160 0.200 0.250 0.315 0.400
2
0.006 0.008 0.025 0.032 0.040 0.050 0.050 0.063 0.080 0.100 0.100 0.125 0.160 0.200 0.200 0.250 0.310 0.400 0.500
3
0.007 0.012 0.032 0.040 0.050 0.063 0.063 0.080 0.100 0.125 0.125 0.160 0.200 0.250 0.250 0.315 0.400 0.500 0.630
7
0.014 0.020 0.080 0.100 0.125 0.160 0.160 0.200 0.250 0.315 0.315 0.400 0.500 0.630 0.630 0.800 1.000 1.250 1.600
8
0.016 0.023 0.100 0.125 0.160 0.200 0.200 0.250 0.315 0.400 0.400 0.500 0.630 0.800 0.800 1.000 1.250 1.600 1.600
9
0.019 0.025 0.125 0.160 0.160 0.200 0.250 0.315 0.315 0.400 0.500 0.630 0.630 0.800 1.000 1.250 1.250 1.600 2.000
Cooling: without coolant ducts with coolant ducts Coolant: Air Neat oil Soluble oil Cutting direction: right-hand cutting left-hand cutting
Material group Common structural steels Free-cutting steels Unalloyed heat-treatable steels
Alloyed heat-treatable steels Unalloyed case hardened steels Alloyed case hardened steels Nitriding steels Tool steels High speed steels Spring steels Stainless steels, sulphured austenitic martensitic Hardened steels Special alloys Cast iron Spheroidal graphite iron and malleable cast iron Chilled cast iron Ti and Ti-alloys Aluminium and Al-alloys Al wrought alloys Al cast alloys 10 % Si > 10 % Si Magnesium alloys Copper, low-alloyed Brass, short-chipping long-chipping Bronze, short-chipping Bronze, long-chipping Duroplastics Thermoplastics Kevlar Glass, carbon concent. plastics
Material examples, new description (old description in brackets) Figures in bold = material no. to DIN EN 1.0035 S185(St33),1.0486 P275N(StE285),1.0345 P235GH(H1),1.0425 P265GH(H2) 1.0050 E295 (St50-2), 1.0070 E360 (St70-2), 1.8937 P500NH (WStE500) 1.0718 11SMnPb30 (9SMnPb28), 1.0736 11SMn37 (9SMn36) 1.0727 46S20 (45S20), 1.0728 (60S20), 1.0757 46SPb20 (45SPb20) 1.0402 C22, 1.1178 C30E (Ck30) 1.0503 C45, 1.1191 C45E (Ck45) 1.0601 C60, 1.1221 C60E (Ck60) 1.5131 50MnSi4, 1.7003 38Cr2, 1.7030 28Cr4 1.5710 36NiCr6, 1.7035 41Cr4, 1.7225 42CrMo4 1.0301 (C10), 1.1121 C10E (Ck10) 1.7043 38Cr4 1.5752 15NiCr13 (15NiCr13), 1.7131 16MnCr5, 1.7264 20CrMo5 1.8504 34CrAl6 1.8519 31CrMoV9, 1.8550 34CrAlNi7 1.1750 C75W, 1.2067 102Cr6, 1.2307 29CrMoV9 1.2080 X210Cr12, 1.2083 X42Cr13, 1.2419 105WCr6, 1.2767 X45NiCrMo4 1.3243 S 6-5-2-5, 1.3343 S 6-5-2, 1.3344 S 6-5-3 1.5026 55Si7, 1.7176 55Cr3, 1.8159 51CrV4 (51CrV4) 1.4005 X12CrS13, 1.4104 X14CrMoS17, 1.4105 X6CrMoS17, 1.4305 X8CrNiS18-9 1.4301 X5CrNi18-10 (V2A), 1.4541 X6CrNiTi18-10, 1.4571 X6CrNiMoTi 17-12-2 (V4A) 1.4057 X20CrNi 17 2 (X17CrNi16-2), 1.4122 X39CrMo17-1, 1.4521 X2CrMoTi18-2 Nimonic, Inconel, Monel, Hastelloy 0.6010 EN-GJL-100(GG10), 0.6020 EN-GJL-200(GG20) 0.6025 EN-GJL-250(GG25), 0.6035 EN-GJL-350(GG35) 0.7050 EN-GJS-500-7(GGG50), 0.8035 EN-GJMW-350-4(GTW35) 0.7070 EN-GJS-700-2(GGG70), 0.8170 EN-GJMB-700-2(GTS70) 3.7024 Ti99,5, 3.7114 TiAl5Sn2,5, 3.7124 TiCu2 3.7154 TiAl6Zr5, 3.7165 TiAl6V4, 3.7184 TiAl4Mo4Sn2,5, - TiAl8Mo1V1 3.0255 Al99,5, 3.2315 AlMgSi1, 3.3515 AlMg1 3.0615 AlMgSiPb, 3.1325 AlCuMg1, 3.3245 AlMg3Si, 3.4365 AlZnMgCu1,5 3.2131 G-AlSi5Cu1, 3.2153 G-AlSi7Cu3, 3.2573 G-AlSi9 3.2581 G-AlSi12, 3.2583 G-AlSi12Cu, - G-AlSi12CuNiMg 3.5200 MgMn2, 3.5812.05 G-MgAl8Zn1, 3.5612.05 G-MgAl6Zn1 2.0070 SE-Cu, 2.1020 CuSn6, 2.1096 G-CuSn5ZnPb 2.0380 CuZn39Pb2, 2.0401 CuZn39Pb3, 2.0410 CuZn43Pb2 2.0250 CuZn20, 2.0280 CuZn33, 2.0332 CuZn37Pb0,5 2.1090 CuSn7ZnPb, 2.1170 CuPb5Sn5, 2.1176 CuPb10Sn 2.0790 CuNi18Zn19Pb 2.0916 CuAl5, 2.0960 CuAl9Mn, 2.1050 CuSn10 2.0980 CuAl11Ni, 2.1247 CuBe2 Bakelit, Resopal, Pertinax, Moltopren Plexiglass, Hostalen, Novodur, Makralon Kevlar GFK/CFK
Tensile strength Hardness MPa (N/mm2) 500 >500-850 850 850-1000 700 700-850 850-1000 850-1000 1000-1200 750 850-1000 1000-1200 850-1000 >1000-1200 850 >850-1000 650-1000 330 HB 850 850 850 40-48 HRC >48-60 HRC 1200 240 HB <300 HB 240 HB <300 HB 350 HB 850 >850-1200 400 450 600 600 450 400 600 600 600 >600-850 850 >850-1000
Coolant
bright
steam tempered
nitrided lands
nitrided
golden brown
TiAlN
62
GUHRINGGUIDE
Tool material Type Surface finish str. DIN 338 MT DIN 345 Std. range, page
HSCO
Ti 2459 662 435 251 657 250 2458 251 1223 251 1224 435
HSCO
GT 100 1221 250 1222 435
GT 100
No.
vc vc m/min m/min
vc m/min
36 32 18 22 18 20 15 18 13 22 13 13 10 18 13 15 4 8 45 36 40 28 10 13 8
47 42 23 28 23 26 20 23 17 28 17 17 12 23 18 20 6 10 59 47 52 23 13 15 10
5 5
5
5 4 4
6
6 5
40
6 5 5 4 7 5 4 5 4 5 4 4 3 5
4
4 4
3
3 3 3 3 4
3 4 3 4 4
5 4
4 4 4
3 3 2 4 3 3 3
4 4 4 4 5
4 5 5
3 3 3 3 4
4 4 4 4 5
2 3 3 1
1
2 3 4 1
1
22 26 20 55 22 17 20 15 26 15 15 15 20 17
6 6
6
6 6 6 6
7 7 7 7 4
3 2 2
3 2 2
55 40 38 32
7 7 7 7
85 70 45
110 91 59 5
7 6 5
8 7 6
105 80 130 55
7 7 7 6
40 36 28 22
47 30 28
4 4
4 4
4
4
5
5
40 32 26
5 5 5
AlTiN
TiCN
FIRE
AlCrN
TiN
MolyGlide
63
Twist Drills
5D drilling depth
Twist Drills
Tools with bold feed column no. are preferred choice.
1
0.004 0.006 0.020 0.025 0.032 0.040 0.040 0.050 0.063 0.080 0.080 0.100 0.125 0.160 0.160 0.200 0.250 0.315 0.400
2
0.006 0.008 0.025 0.032 0.040 0.050 0.050 0.063 0.080 0.100 0.100 0.125 0.160 0.200 0.200 0.250 0.310 0.400 0.500
3
0.007 0.012 0.032 0.040 0.050 0.063 0.063 0.080 0.100 0.125 0.125 0.160 0.200 0.250 0.250 0.315 0.400 0.500 0.630
7
0.014 0.020 0.080 0.100 0.125 0.160 0.160 0.200 0.250 0.315 0.315 0.400 0.500 0.630 0.630 0.800 1.000 1.250 1.600
8
0.016 0.023 0.100 0.125 0.160 0.200 0.200 0.250 0.315 0.400 0.400 0.500 0.630 0.800 0.800 1.000 1.250 1.600 1.600
9
0.019 0.025 0.125 0.160 0.160 0.200 0.250 0.315 0.315 0.400 0.500 0.630 0.630 0.800 1.000 1.250 1.250 1.600 2.000
Cooling: without coolant ducts with coolant ducts Coolant: Air Neat oil Soluble oil Cutting direction: right-hand cutting left-hand cutting * Cutting lip corrected to appr. 10
Material group Common structural steels Free-cutting steels Unalloyed heat-treatable steels
Alloyed heat-treatable steels Unalloyed case hardened steels Alloyed case hardened steels Nitriding steels Tool steels High speed steels Spring steels Stainless steels, sulphured austenitic martensitic Hardened steels Special alloys Cast iron Spheroidal graphite iron and malleable cast iron Chilled cast iron Ti and Ti-alloys Aluminium and Al-alloys Al wrought alloys Al cast alloys 10 % Si > 10 % Si Magnesium alloys Copper, low-alloyed Brass, short-chipping long-chipping Bronze, short-chipping Bronze, long-chipping Duroplastics Thermoplastics Kevlar Glass, carbon concent. plastics
Material examples, new description (old description in brackets) Figures in bold = material no. to DIN EN 1.0035 S185(St33),1.0486 P275N(StE285),1.0345 P235GH(H1),1.0425 P265GH(H2) 1.0050 E295 (St50-2), 1.0070 E360 (St70-2), 1.8937 P500NH (WStE500) 1.0718 11SMnPb30 (9SMnPb28), 1.0736 11SMn37 (9SMn36) 1.0727 46S20 (45S20), 1.0728 (60S20), 1.0757 46SPb20 (45SPb20) 1.0402 C22, 1.1178 C30E (Ck30) 1.0503 C45, 1.1191 C45E (Ck45) 1.0601 C60, 1.1221 C60E (Ck60) 1.5131 50MnSi4, 1.7003 38Cr2, 1.7030 28Cr4 1.5710 36NiCr6, 1.7035 41Cr4, 1.7225 42CrMo4 1.0301 (C10), 1.1121 C10E (Ck10) 1.7043 38Cr4 1.5752 15NiCr13 (15NiCr13), 1.7131 16MnCr5, 1.7264 20CrMo5 1.8504 34CrAl6 1.8519 31CrMoV9, 1.8550 34CrAlNi7 1.1750 C75W, 1.2067 102Cr6, 1.2307 29CrMoV9 1.2080 X210Cr12, 1.2083 X42Cr13, 1.2419 105WCr6, 1.2767 X45NiCrMo4 1.3243 S 6-5-2-5, 1.3343 S 6-5-2, 1.3344 S 6-5-3 1.5026 55Si7, 1.7176 55Cr3, 1.8159 51CrV4 (51CrV4) 1.4005 X12CrS13, 1.4104 X14CrMoS17, 1.4105 X6CrMoS17, 1.4305 X8CrNiS18-9 1.4301 X5CrNi18-10 (V2A), 1.4541 X6CrNiTi18-10, 1.4571 X6CrNiMoTi 17-12-2 (V4A) 1.4057 X20CrNi 17 2 (X17CrNi16-2), 1.4122 X39CrMo17-1, 1.4521 X2CrMoTi18-2 Nimonic, Inconel, Monel, Hastelloy 0.6010 EN-GJL-100(GG10), 0.6020 EN-GJL-200(GG20) 0.6025 EN-GJL-250(GG25), 0.6035 EN-GJL-350(GG35) 0.7050 EN-GJS-500-7(GGG50), 0.8035 EN-GJMW-350-4(GTW35) 0.7070 EN-GJS-700-2(GGG70), 0.8170 EN-GJMB-700-2(GTS70) 3.7024 Ti99,5, 3.7114 TiAl5Sn2,5, 3.7124 TiCu2 3.7154 TiAl6Zr5, 3.7165 TiAl6V4, 3.7184 TiAl4Mo4Sn2,5, - TiAl8Mo1V1 3.0255 Al99,5, 3.2315 AlMgSi1, 3.3515 AlMg1 3.0615 AlMgSiPb, 3.1325 AlCuMg1, 3.3245 AlMg3Si, 3.4365 AlZnMgCu1,5 3.2131 G-AlSi5Cu1, 3.2153 G-AlSi7Cu3, 3.2573 G-AlSi9 3.2581 G-AlSi12, 3.2583 G-AlSi12Cu, - G-AlSi12CuNiMg 3.5200 MgMn2, 3.5812.05 G-MgAl8Zn1, 3.5612.05 G-MgAl6Zn1 2.0070 SE-Cu, 2.1020 CuSn6, 2.1096 G-CuSn5ZnPb 2.0380 CuZn39Pb2, 2.0401 CuZn39Pb3, 2.0410 CuZn43Pb2 2.0250 CuZn20, 2.0280 CuZn33, 2.0332 CuZn37Pb0,5 2.1090 CuSn7ZnPb, 2.1170 CuPb5Sn5, 2.1176 CuPb10Sn 2.0790 CuNi18Zn19Pb 2.0916 CuAl5, 2.0960 CuAl9Mn, 2.1050 CuSn10 2.0980 CuAl11Ni, 2.1247 CuBe2 Bakelit, Resopal, Pertinax, Moltopren Plexiglass, Hostalen, Novodur, Makralon Kevlar GFK/CFK
Tensile strength Hardness MPa (N/mm2) 500 >500-850 850 850-1000 700 700-850 850-1000 850-1000 1000-1200 750 850-1000 1000-1200 850-1000 >1000-1200 850 >850-1000 650-1000 330 HB 850 850 850 40-48 HRC >48-60 HRC 1200 240 HB <300 HB 240 HB <300 HB 350 HB 850 >850-1200 400 450 600 600 450 400 600 600 600 >600-850 850 >850-1000
Coolant
bright
steam tempered
nitrided lands
nitrided
golden brown
TiAlN
64
GUHRINGGUIDE
Tool material Type Surface finish Internal cooling DIN 338 DIN 6537 G.S. Std. range, page
str. shank
HSCO
P2000
HSCO
PM HSS-E
GT 500
HSCO
GT 80 IK
Carbide
N
GU 500
Guh. no.
2047 1131 251 511 336 513 334 362 1132 732 362 251 2464 251
vc m/min 32 25 32 28 32 28 18 18 14 32 16 12 14 10 16 10 10 8 14 10 12
vc m/min 45 35 50 40 42 35 22 18 15 40 20 15 18 12 18 13 13 18 12 15
vc m/min 50 40 60 50 50 40 32 32 28 48 25 20 25 20 28 17 20 12 18 12 15
vc vc m/min m/min 48 38 48 38 48 38 20 25 20 50 22 16 20 14 24 14 14 12 20 14 16 4 10 48 38 42 30 12 14 10 60 48 60 48 60 48 25 30 25 62 28 20 25 18 30 18 18 15 25 18 20 5 12 60 48 52 38 15 18 12 7 6 7 6 6 6
6 5 5 5 4 4
3 6 4 3 3 4 3 3 2 4 3 3 6 5
6 5 6 5 6 6 5 6
4 3 4 3 4 3
5 4
4 4 4 4 5 4 4 3
6 5
5 5 5 5 6 5 5 4
5 3 4 3 4 4 5 4 4 2
4 3 3
5 5 4 5 4 5 4 4 4 3 5 4 4 3 2 7 7 4 3
7 8 6 6 5 5 3 7 7 5 7
5 5 4 5 4 5 4 4 4 3 5 4 4 3 2 7 7 4 3
7 8 6 6 5 5 3 7 7 5 7
4 3
3
4 4 4
30 30 30 30 25 20 115 100 90 80 25 20 260 260 195 155 235 100 235 235 155 155 90 65 50 65 100
4 3 3
3
5 4 4
3
36 28 30 22 8
6 6 6 6 3
45 36 40 28
6 6 6 6
55 45 52 34 13
7 7 4
7
2 4 4 4 3 2 7 7 6 6 5 5*
5* 5* 5 5 4 3 4 3 3 4
3 5 5 5 4 3 8 8 7 7 6 6
6 6 6 6 5 4 5 4 4 5
90 90 70 55 80 32 63 40 36 28 25 22 25 22
7 7 7 6 6 5 5 5 4 4 4 4 4 5
70 70 85 70 70 32 63 40 50 35 32 28 25 15
7 7 7 6 5 5 5 4 4 4 4 4 4
6
85 76
7 6
95 75 48 60 42 38 30 38
120 95 60 75 52 48 38 48
5
6
5
6
AlTiN
TiCN
FIRE
AlCrN
TiN
MolyGlide
65
Twist Drills
5D drilling depth
Twist Drills
Tools with bold feed column no. are preferred choice.
1
0.004 0.006 0.020 0.025 0.032 0.040 0.040 0.050 0.063 0.080 0.080 0.100 0.125 0.160 0.160 0.200 0.250 0.315 0.400
2
0.006 0.008 0.025 0.032 0.040 0.050 0.050 0.063 0.080 0.100 0.100 0.125 0.160 0.200 0.200 0.250 0.310 0.400 0.500
3
0.007 0.012 0.032 0.040 0.050 0.063 0.063 0.080 0.100 0.125 0.125 0.160 0.200 0.250 0.250 0.315 0.400 0.500 0.630
7
0.014 0.020 0.080 0.100 0.125 0.160 0.160 0.200 0.250 0.315 0.315 0.400 0.500 0.630 0.630 0.800 1.000 1.250 1.600
8
0.016 0.023 0.100 0.125 0.160 0.200 0.200 0.250 0.315 0.400 0.400 0.500 0.630 0.800 0.800 1.000 1.250 1.600 1.600
9
0.019 0.025 0.125 0.160 0.160 0.200 0.250 0.315 0.315 0.400 0.500 0.630 0.630 0.800 1.000 1.250 1.250 1.600 2.000
Cooling: without coolant ducts with coolant ducts Coolant: Air Neat oil Soluble oil Cutting direction: right-hand cutting left-hand cutting * Use bright finish drills or use drills with bright polished flutes.
Material group Common structural steels Free-cutting steels Unalloyed heat-treatable steels
Alloyed heat-treatable steels Unalloyed case hardened steels Alloyed case hardened steels Nitriding steels Tool steels High speed steels Spring steels Stainless steels, sulphured austenitic martensitic Hardened steels Special alloys Cast iron Spheroidal graphite iron and malleable cast iron Chilled cast iron Ti and Ti-alloys Aluminium and Al-alloys Al wrought alloys Al cast alloys 10 % Si > 10 % Si Magnesium alloys Copper, low-alloyed Brass, short-chipping long-chipping Bronze, short-chipping Bronze, long-chipping Duroplastics Thermoplastics Kevlar Glass, carbon concent. plastics
Material examples, new description (old description in brackets) Figures in bold = material no. to DIN EN 1.0035 S185(St33),1.0486 P275N(StE285),1.0345 P235GH(H1),1.0425 P265GH(H2) 1.0050 E295 (St50-2), 1.0070 E360 (St70-2), 1.8937 P500NH (WStE500) 1.0718 11SMnPb30 (9SMnPb28), 1.0736 11SMn37 (9SMn36) 1.0727 46S20 (45S20), 1.0728 (60S20), 1.0757 46SPb20 (45SPb20) 1.0402 C22, 1.1178 C30E (Ck30) 1.0503 C45, 1.1191 C45E (Ck45) 1.0601 C60, 1.1221 C60E (Ck60) 1.5131 50MnSi4, 1.7003 38Cr2, 1.7030 28Cr4 1.5710 36NiCr6, 1.7035 41Cr4, 1.7225 42CrMo4 1.0301 (C10), 1.1121 C10E (Ck10) 1.7043 38Cr4 1.5752 15NiCr13 (15NiCr13), 1.7131 16MnCr5, 1.7264 20CrMo5 1.8504 34CrAl6 1.8519 31CrMoV9, 1.8550 34CrAlNi7 1.1750 C75W, 1.2067 102Cr6, 1.2307 29CrMoV9 1.2080 X210Cr12, 1.2083 X42Cr13, 1.2419 105WCr6, 1.2767 X45NiCrMo4 1.3243 S 6-5-2-5, 1.3343 S 6-5-2, 1.3344 S 6-5-3 1.5026 55Si7, 1.7176 55Cr3, 1.8159 51CrV4 (51CrV4) 1.4005 X12CrS13, 1.4104 X14CrMoS17, 1.4105 X6CrMoS17, 1.4305 X8CrNiS18-9 1.4301 X5CrNi18-10 (V2A), 1.4541 X6CrNiTi18-10, 1.4571 X6CrNiMoTi 17-12-2 (V4A) 1.4057 X20CrNi 17 2 (X17CrNi16-2), 1.4122 X39CrMo17-1, 1.4521 X2CrMoTi18-2 Nimonic, Inconel, Monel, Hastelloy 0.6010 EN-GJL-100(GG10), 0.6020 EN-GJL-200(GG20) 0.6025 EN-GJL-250(GG25), 0.6035 EN-GJL-350(GG35) 0.7050 EN-GJS-500-7(GGG50), 0.8035 EN-GJMW-350-4(GTW35) 0.7070 EN-GJS-700-2(GGG70), 0.8170 EN-GJMB-700-2(GTS70) 3.7024 Ti99,5, 3.7114 TiAl5Sn2,5, 3.7124 TiCu2 3.7154 TiAl6Zr5, 3.7165 TiAl6V4, 3.7184 TiAl4Mo4Sn2,5, - TiAl8Mo1V1 3.0255 Al99,5, 3.2315 AlMgSi1, 3.3515 AlMg1 3.0615 AlMgSiPb, 3.1325 AlCuMg1, 3.3245 AlMg3Si, 3.4365 AlZnMgCu1,5 3.2131 G-AlSi5Cu1, 3.2153 G-AlSi7Cu3, 3.2573 G-AlSi9 3.2581 G-AlSi12, 3.2583 G-AlSi12Cu, - G-AlSi12CuNiMg 3.5200 MgMn2, 3.5812.05 G-MgAl8Zn1, 3.5612.05 G-MgAl6Zn1 2.0070 SE-Cu, 2.1020 CuSn6, 2.1096 G-CuSn5ZnPb 2.0380 CuZn39Pb2, 2.0401 CuZn39Pb3, 2.0410 CuZn43Pb2 2.0250 CuZn20, 2.0280 CuZn33, 2.0332 CuZn37Pb0,5 2.1090 CuSn7ZnPb, 2.1170 CuPb5Sn5, 2.1176 CuPb10Sn 2.0790 CuNi18Zn19Pb 2.0916 CuAl5, 2.0960 CuAl9Mn, 2.1050 CuSn10 2.0980 CuAl11Ni, 2.1247 CuBe2 Bakelit, Resopal, Pertinax, Moltopren Plexiglass, Hostalen, Novodur, Makralon Kevlar GFK/CFK
Tensile strength Hardness MPa (N/mm2) 500 >500-850 850 850-1000 700 700-850 850-1000 850-1000 1000-1200 750 850-1000 1000-1200 850-1000 >1000-1200 850 >850-1000 650-1000 330 HB 850 850 850 40-48 HRC >48-60 HRC 1200 240 HB <300 HB 240 HB <300 HB 350 HB 850 >850-1200 400 450 600 600 450 400 600 600 600 >600-850 850 >850-1000
Coolant
bright
steam tempered
nitrided lands
nitrided
golden brown
TiAlN
66
GUHRINGGUIDE
straight shank
Tool material Type Surface finish Internal cooling DIN 339 DIN 340
HSS
HSS
N W GT50 GT100 N
HSS
GT 100
561 562
211 204 217 220 257 374 364 373 373 462 523 469 373 373 218 221 219 501 535 506 505 373 462 551 374 462 373
Guh. no.
vc m/min 28 22 28 22 28 22 6 5 6 5 5 5
vc m/min 28 22 28 22 28 22
vc vc m/min m/min
6 5 6 5 5
5
36 28 36 28 36 28 22 18 36 14 12
47 36 47 36 47 36 29 23 47 18 15 23 10
6 5 6 5 5
4 4 5
7 6 7 6 6
5 5 6
28
28
6
4 4 4 3
7
5 5 5 4
14
14
18 8
28 22 22 18
6 6 6 6
6 6 6 6
28 22 22 18
6 6
6 6
36 28 28 22
47 36 36 29
6 6 6 6
6 6
6 6
7 7
7 7
70 70 55 45 70 28 55 34 28 22 22 14 22
7 6 6 5 5 4 4 4 4 5
7* 6* 6* 5* 5* 4* 4* 4* 4 5*
70 70 55 45 70 28 34
7 7 7
6
7 7 6
7 6 5 5 4
6 4
70 55 95 36 45 36 28 28 22 18 28
90 72 47 58
7 6 6 5 5
7 6 5 5 4 4
4
8 7 6 6 5 5
5
22 14 22 4
36 29 23
4 4
4 4 4 5
AlTiN
TiCN
FIRE
AlCrN
TiN
MolyGlide
67
Twist Drills
If flute length permits, DIN 338 and DIN 345 can also be applied for holes 10 x D.
Twist Drills
Tools with bold feed column no. are preferred choice.
1
0.004 0.006 0.020 0.025 0.032 0.040 0.040 0.050 0.063 0.080 0.080 0.100 0.125 0.160 0.160 0.200 0.250 0.315 0.400
2
0.006 0.008 0.025 0.032 0.040 0.050 0.050 0.063 0.080 0.100 0.100 0.125 0.160 0.200 0.200 0.250 0.310 0.400 0.500
3
0.007 0.012 0.032 0.040 0.050 0.063 0.063 0.080 0.100 0.125 0.125 0.160 0.200 0.250 0.250 0.315 0.400 0.500 0.630
7
0.014 0.020 0.080 0.100 0.125 0.160 0.160 0.200 0.250 0.315 0.315 0.400 0.500 0.630 0.630 0.800 1.000 1.250 1.600
8
0.016 0.023 0.100 0.125 0.160 0.200 0.200 0.250 0.315 0.400 0.400 0.500 0.630 0.800 0.800 1.000 1.250 1.600 1.600
9
0.019 0.025 0.125 0.160 0.160 0.200 0.250 0.315 0.315 0.400 0.500 0.630 0.630 0.800 1.000 1.250 1.250 1.600 2.000
Cooling: without coolant ducts with coolant ducts Coolant: Air Neat oil Soluble oil Cutting direction: right-hand cutting left-hand cutting * Use bright finish drills or use drills with bright polished flutes.
Material group Common structural steels Free-cutting steels Unalloyed heat-treatable steels
Alloyed heat-treatable steels Unalloyed case hardened steels Alloyed case hardened steels Nitriding steels Tool steels High speed steels Spring steels Stainless steels, sulphured austenitic martensitic Hardened steels Special alloys Cast iron Spheroidal graphite iron and malleable cast iron Chilled cast iron Ti and Ti-alloys Aluminium and Al-alloys Al wrought alloys Al cast alloys 10 % Si > 10 % Si Magnesium alloys Copper, low-alloyed Brass, short-chipping long-chipping Bronze, short-chipping Bronze, long-chipping Duroplastics Thermoplastics Kevlar Glass, carbon concent. plastics
Material examples, new description (old description in brackets) Figures in bold = material no. to DIN EN 1.0035 S185(St33),1.0486 P275N(StE285),1.0345 P235GH(H1),1.0425 P265GH(H2) 1.0050 E295 (St50-2), 1.0070 E360 (St70-2), 1.8937 P500NH (WStE500) 1.0718 11SMnPb30 (9SMnPb28), 1.0736 11SMn37 (9SMn36) 1.0727 46S20 (45S20), 1.0728 (60S20), 1.0757 46SPb20 (45SPb20) 1.0402 C22, 1.1178 C30E (Ck30) 1.0503 C45, 1.1191 C45E (Ck45) 1.0601 C60, 1.1221 C60E (Ck60) 1.5131 50MnSi4, 1.7003 38Cr2, 1.7030 28Cr4 1.5710 36NiCr6, 1.7035 41Cr4, 1.7225 42CrMo4 1.0301 (C10), 1.1121 C10E (Ck10) 1.7043 38Cr4 1.5752 15NiCr13 (15NiCr13), 1.7131 16MnCr5, 1.7264 20CrMo5 1.8504 34CrAl6 1.8519 31CrMoV9, 1.8550 34CrAlNi7 1.1750 C75W, 1.2067 102Cr6, 1.2307 29CrMoV9 1.2080 X210Cr12, 1.2083 X42Cr13, 1.2419 105WCr6, 1.2767 X45NiCrMo4 1.3243 S 6-5-2-5, 1.3343 S 6-5-2, 1.3344 S 6-5-3 1.5026 55Si7, 1.7176 55Cr3, 1.8159 51CrV4 (51CrV4) 1.4005 X12CrS13, 1.4104 X14CrMoS17, 1.4105 X6CrMoS17, 1.4305 X8CrNiS18-9 1.4301 X5CrNi18-10 (V2A), 1.4541 X6CrNiTi18-10, 1.4571 X6CrNiMoTi 17-12-2 (V4A) 1.4057 X20CrNi 17 2 (X17CrNi16-2), 1.4122 X39CrMo17-1, 1.4521 X2CrMoTi18-2 Nimonic, Inconel, Monel, Hastelloy 0.6010 EN-GJL-100(GG10), 0.6020 EN-GJL-200(GG20) 0.6025 EN-GJL-250(GG25), 0.6035 EN-GJL-350(GG35) 0.7050 EN-GJS-500-7(GGG50), 0.8035 EN-GJMW-350-4(GTW35) 0.7070 EN-GJS-700-2(GGG70), 0.8170 EN-GJMB-700-2(GTS70) 3.7024 Ti99,5, 3.7114 TiAl5Sn2,5, 3.7124 TiCu2 3.7154 TiAl6Zr5, 3.7165 TiAl6V4, 3.7184 TiAl4Mo4Sn2,5, - TiAl8Mo1V1 3.0255 Al99,5, 3.2315 AlMgSi1, 3.3515 AlMg1 3.0615 AlMgSiPb, 3.1325 AlCuMg1, 3.3245 AlMg3Si, 3.4365 AlZnMgCu1,5 3.2131 G-AlSi5Cu1, 3.2153 G-AlSi7Cu3, 3.2573 G-AlSi9 3.2581 G-AlSi12, 3.2583 G-AlSi12Cu, - G-AlSi12CuNiMg 3.5200 MgMn2, 3.5812.05 G-MgAl8Zn1, 3.5612.05 G-MgAl6Zn1 2.0070 SE-Cu, 2.1020 CuSn6, 2.1096 G-CuSn5ZnPb 2.0380 CuZn39Pb2, 2.0401 CuZn39Pb3, 2.0410 CuZn43Pb2 2.0250 CuZn20, 2.0280 CuZn33, 2.0332 CuZn37Pb0,5 2.1090 CuSn7ZnPb, 2.1170 CuPb5Sn5, 2.1176 CuPb10Sn 2.0790 CuNi18Zn19Pb 2.0916 CuAl5, 2.0960 CuAl9Mn, 2.1050 CuSn10 2.0980 CuAl11Ni, 2.1247 CuBe2 Bakelit, Resopal, Pertinax, Moltopren Plexiglass, Hostalen, Novodur, Makralon Kevlar GFK/CFK
Tensile strength Hardness MPa (N/mm2) 500 >500-850 850 850-1000 700 700-850 850-1000 850-1000 1000-1200 750 850-1000 1000-1200 850-1000 >1000-1200 850 >850-1000 650-1000 330 HB 850 850 850 40-48 HRC >48-60 HRC 1200 240 HB <300 HB 240 HB <300 HB 350 HB 850 >850-1200 400 450 600 600 450 400 600 600 600 >600-850 850 >850-1000
Coolant
bright
steam tempered
nitrided lands
nitrided
golden brown
TiAlN
68
GUHRINGGUIDE
Tool material Type Surface finish Internal cooling Guh. no. MT straight G.S. G.S.
HSS
Tool material Type Surface finish Internal cooling straight shank Guh. no. DIN 1869
HSS
series 3 p. 412
GT 50
390
1 2
235
1
524
6
270
3
271
4
272
5
1101
6
236 237
2 3 5
528 529
7 9 8 10
MT
473
473
473
472
266 267
4
If flute length permits, DIN 338 and DIN 345 can also be applied for holes 10 x D.
s. right
vc m/min 40 30 40 30 40 30 22 20 14 40 17 12 14 10 20 10 10 7 14 10 12 4 6 40 30 35 25 7 10 6 80 75 60 40 50 35 30 25 30 6 5 6
vc m/min 22 18 22 18 22 18 1 2 3 12 22 10 8 12 6 6 8
5 5 5
4 4 3 4 3 4 3 3 3 2 4 3 3 2 1 6 6 3 2 2
5 5 5
4 4 3 4 3 4 3 3 3 2 4 3 3 2 1 6 6 3 2 2
6 6
6 6
22 18 20 14
5 5 5 5
6 7 6 5 5 4 4
4
7* 6* 5* 5* 4* 4*
4*
55 55 45 36 55 22 45 28 22 20 18 12 18 4 5 6
5*
6* 5* 5* 4* 4* 4* 3* 3* 3* 3* 3 4*
6 6
5
10
AlTiN
TiCN
FIRE
AlCrN
TiN
MolyGlide
69
Twist Drills
Twist Drills
Tools with bold feed column no. are preferred choice.
1
0.004 0.006 0.020 0.025 0.032 0.040 0.040 0.050 0.063 0.080 0.080 0.100 0.125 0.160 0.160 0.200 0.250 0.315 0.400
2
0.006 0.008 0.025 0.032 0.040 0.050 0.050 0.063 0.080 0.100 0.100 0.125 0.160 0.200 0.200 0.250 0.310 0.400 0.500
3
0.007 0.012 0.032 0.040 0.050 0.063 0.063 0.080 0.100 0.125 0.125 0.160 0.200 0.250 0.250 0.315 0.400 0.500 0.630
7
0.014 0.020 0.080 0.100 0.125 0.160 0.160 0.200 0.250 0.315 0.315 0.400 0.500 0.630 0.630 0.800 1.000 1.250 1.600
8
0.016 0.023 0.100 0.125 0.160 0.200 0.200 0.250 0.315 0.400 0.400 0.500 0.630 0.800 0.800 1.000 1.250 1.600 1.600
9
0.019 0.025 0.125 0.160 0.160 0.200 0.250 0.315 0.315 0.400 0.500 0.630 0.630 0.800 1.000 1.250 1.250 1.600 2.000
Cooling: without coolant ducts with coolant ducts Coolant: Air Neat oil Soluble oil Cutting direction: right-hand cutting left-hand cutting
Material group Common structural steels Free-cutting steels Unalloyed heat-treatable steels
Alloyed heat-treatable steels Unalloyed case hardened steels Alloyed case hardened steels Nitriding steels Tool steels High speed steels Spring steels Stainless steels, sulphured austenitic martensitic Hardened steels Special alloys Cast iron Spheroidal graphite iron and malleable cast iron Chilled cast iron Ti and Ti-alloys Aluminium and Al-alloys Al wrought alloys Al cast alloys 10 % Si > 10 % Si Magnesium alloys Copper, low-alloyed Brass, short-chipping long-chipping Bronze, short-chipping Bronze, long-chipping Duroplastics Thermoplastics Kevlar Glass, carbon concent. plastics
Material examples, new description (old description in brackets) Figures in bold = material no. to DIN EN 1.0035 S185(St33),1.0486 P275N(StE285),1.0345 P235GH(H1),1.0425 P265GH(H2) 1.0050 E295 (St50-2), 1.0070 E360 (St70-2), 1.8937 P500NH (WStE500) 1.0718 11SMnPb30 (9SMnPb28), 1.0736 11SMn37 (9SMn36) 1.0727 46S20 (45S20), 1.0728 (60S20), 1.0757 46SPb20 (45SPb20) 1.0402 C22, 1.1178 C30E (Ck30) 1.0503 C45, 1.1191 C45E (Ck45) 1.0601 C60, 1.1221 C60E (Ck60) 1.5131 50MnSi4, 1.7003 38Cr2, 1.7030 28Cr4 1.5710 36NiCr6, 1.7035 41Cr4, 1.7225 42CrMo4 1.0301 (C10), 1.1121 C10E (Ck10) 1.7043 38Cr4 1.5752 15NiCr13 (15NiCr13), 1.7131 16MnCr5, 1.7264 20CrMo5 1.8504 34CrAl6 1.8519 31CrMoV9, 1.8550 34CrAlNi7 1.1750 C75W, 1.2067 102Cr6, 1.2307 29CrMoV9 1.2080 X210Cr12, 1.2083 X42Cr13, 1.2419 105WCr6, 1.2767 X45NiCrMo4 1.3243 S 6-5-2-5, 1.3343 S 6-5-2, 1.3344 S 6-5-3 1.5026 55Si7, 1.7176 55Cr3, 1.8159 51CrV4 (51CrV4) 1.4005 X12CrS13, 1.4104 X14CrMoS17, 1.4105 X6CrMoS17, 1.4305 X8CrNiS18-9 1.4301 X5CrNi18-10 (V2A), 1.4541 X6CrNiTi18-10, 1.4571 X6CrNiMoTi 17-12-2 (V4A) 1.4057 X20CrNi 17 2 (X17CrNi16-2), 1.4122 X39CrMo17-1, 1.4521 X2CrMoTi18-2 Nimonic, Inconel, Monel, Hastelloy 0.6010 EN-GJL-100(GG10), 0.6020 EN-GJL-200(GG20) 0.6025 EN-GJL-250(GG25), 0.6035 EN-GJL-350(GG35) 0.7050 EN-GJS-500-7(GGG50), 0.8035 EN-GJMW-350-4(GTW35) 0.7070 EN-GJS-700-2(GGG70), 0.8170 EN-GJMB-700-2(GTS70) 3.7024 Ti99,5, 3.7114 TiAl5Sn2,5, 3.7124 TiCu2 3.7154 TiAl6Zr5, 3.7165 TiAl6V4, 3.7184 TiAl4Mo4Sn2,5, - TiAl8Mo1V1 3.0255 Al99,5, 3.2315 AlMgSi1, 3.3515 AlMg1 3.0615 AlMgSiPb, 3.1325 AlCuMg1, 3.3245 AlMg3Si, 3.4365 AlZnMgCu1,5 3.2131 G-AlSi5Cu1, 3.2153 G-AlSi7Cu3, 3.2573 G-AlSi9 3.2581 G-AlSi12, 3.2583 G-AlSi12Cu, - G-AlSi12CuNiMg 3.5200 MgMn2, 3.5812.05 G-MgAl8Zn1, 3.5612.05 G-MgAl6Zn1 2.0070 SE-Cu, 2.1020 CuSn6, 2.1096 G-CuSn5ZnPb 2.0380 CuZn39Pb2, 2.0401 CuZn39Pb3, 2.0410 CuZn43Pb2 2.0250 CuZn20, 2.0280 CuZn33, 2.0332 CuZn37Pb0,5 2.1090 CuSn7ZnPb, 2.1170 CuPb5Sn5, 2.1176 CuPb10Sn 2.0790 CuNi18Zn19Pb 2.0916 CuAl5, 2.0960 CuAl9Mn, 2.1050 CuSn10 2.0980 CuAl11Ni, 2.1247 CuBe2 Bakelit, Resopal, Pertinax, Moltopren Plexiglass, Hostalen, Novodur, Makralon Kevlar GFK/CFK
Tensile strength Hardness MPa (N/mm2) 500 >500-850 850 850-1000 700 700-850 850-1000 850-1000 1000-1200 750 850-1000 1000-1200 850-1000 >1000-1200 850 >850-1000 650-1000 330 HB 850 850 850 40-48 HRC >48-60 HRC 1200 240 HB <300 HB 240 HB <300 HB 350 HB 850 >850-1200 400 450 600 600 450 400 600 600 600 >600-850 850 >850-1000
Coolant
bright
steam tempered
nitrided lands
nitrided
golden brown
TiAlN
70
GUHRINGGUIDE
HSS
HSS
GT 100 502
1
GT 100 670
2
503 504
3 8 5
671
4
Guh. no.
Morse taper
series 2
vc m/min 22 18 22 18 22 18 12 22 10 8 12 6 6 8
vc m/min 28 22 28 22 28 22 16 15 10 28 12 10 10 8 12 8 8 6 10 8 10
5 4 5 4 4
3 4
5 4 5 4 4 4 3 3 5 3 3 3 2 2 1
3 2 2 2 2 2
1 p. 404
2 p. 404
3 p. 408
4 p. 408
5
3 3 3 2 2 3
series 3
series 2
series 1
22 18 20 14
5 5
5 5
55 55 45 36 55 22 45 28 22 20 18 12 18
6 5 5 4 4
3
6 28 22 25 18 6 8 6 70 70 55 45 70 28 36 28 25 22 18 15 22
5 5 5
5 2 1 1 6 6
6 5 5 4 4 3 3 3 3
4 3
3 3 3
4
5 p. 412
6 p. 478
7 p. 482
8 p. 415
9 p. 416
10 p. 417
11 p. 485
12 p. 486
13 p. 487
14 p. 485
15 p. 486
16 p. 488
17 p. 489
AlTiN
TiCN
FIRE
AlCrN
TiN
MolyGlide
71
Twist Drills
Twist Drills
Tools with bold feed column no. are preferred choice.
1
0.004 0.006 0.020 0.025 0.032 0.040 0.040 0.050 0.063 0.080 0.080 0.100 0.125 0.160 0.160 0.200 0.250 0.315 0.400
2
0.006 0.008 0.025 0.032 0.040 0.050 0.050 0.063 0.080 0.100 0.100 0.125 0.160 0.200 0.200 0.250 0.310 0.400 0.500
3
0.007 0.012 0.032 0.040 0.050 0.063 0.063 0.080 0.100 0.125 0.125 0.160 0.200 0.250 0.250 0.315 0.400 0.500 0.630
7
0.014 0.020 0.080 0.100 0.125 0.160 0.160 0.200 0.250 0.315 0.315 0.400 0.500 0.630 0.630 0.800 1.000 1.250 1.600
8
0.016 0.023 0.100 0.125 0.160 0.200 0.200 0.250 0.315 0.400 0.400 0.500 0.630 0.800 0.800 1.000 1.250 1.600 1.600
9
0.019 0.025 0.125 0.160 0.160 0.200 0.250 0.315 0.315 0.400 0.500 0.630 0.630 0.800 1.000 1.250 1.250 1.600 2.000
Cooling: without coolant ducts with coolant ducts Coolant: Air Neat oil Soluble oil Cutting direction: right-hand cutting left-hand cutting * Use bright finish drills or use drills with bright polished flutes.
Material group Common structural steels Free-cutting steels Unalloyed heat-treatable steels
Alloyed heat-treatable steels Unalloyed case hardened steels Alloyed case hardened steels Nitriding steels Tool steels High speed steels Spring steels Stainless steels, sulphured austenitic martensitic Hardened steels Special alloys Cast iron Spheroidal graphite iron and malleable cast iron Chilled cast iron Ti and Ti-alloys Aluminium and Al-alloys Al wrought alloys Al cast alloys 10 % Si > 10 % Si Magnesium alloys Copper, low-alloyed Brass, short-chipping long-chipping Bronze, short-chipping Bronze, long-chipping Duroplastics Thermoplastics Kevlar Glass, carbon concent. plastics
Material examples, new description (old description in brackets) Figures in bold = material no. to DIN EN 1.0035 S185(St33),1.0486 P275N(StE285),1.0345 P235GH(H1),1.0425 P265GH(H2) 1.0050 E295 (St50-2), 1.0070 E360 (St70-2), 1.8937 P500NH (WStE500) 1.0718 11SMnPb30 (9SMnPb28), 1.0736 11SMn37 (9SMn36) 1.0727 46S20 (45S20), 1.0728 (60S20), 1.0757 46SPb20 (45SPb20) 1.0402 C22, 1.1178 C30E (Ck30) 1.0503 C45, 1.1191 C45E (Ck45) 1.0601 C60, 1.1221 C60E (Ck60) 1.5131 50MnSi4, 1.7003 38Cr2, 1.7030 28Cr4 1.5710 36NiCr6, 1.7035 41Cr4, 1.7225 42CrMo4 1.0301 (C10), 1.1121 C10E (Ck10) 1.7043 38Cr4 1.5752 15NiCr13 (15NiCr13), 1.7131 16MnCr5, 1.7264 20CrMo5 1.8504 34CrAl6 1.8519 31CrMoV9, 1.8550 34CrAlNi7 1.1750 C75W, 1.2067 102Cr6, 1.2307 29CrMoV9 1.2080 X210Cr12, 1.2083 X42Cr13, 1.2419 105WCr6, 1.2767 X45NiCrMo4 1.3243 S 6-5-2-5, 1.3343 S 6-5-2, 1.3344 S 6-5-3 1.5026 55Si7, 1.7176 55Cr3, 1.8159 51CrV4 (51CrV4) 1.4005 X12CrS13, 1.4104 X14CrMoS17, 1.4105 X6CrMoS17, 1.4305 X8CrNiS18-9 1.4301 X5CrNi18-10 (V2A), 1.4541 X6CrNiTi18-10, 1.4571 X6CrNiMoTi 17-12-2 (V4A) 1.4057 X20CrNi 17 2 (X17CrNi16-2), 1.4122 X39CrMo17-1, 1.4521 X2CrMoTi18-2 Nimonic, Inconel, Monel, Hastelloy 0.6010 EN-GJL-100(GG10), 0.6020 EN-GJL-200(GG20) 0.6025 EN-GJL-250(GG25), 0.6035 EN-GJL-350(GG35) 0.7050 EN-GJS-500-7(GGG50), 0.8035 EN-GJMW-350-4(GTW35) 0.7070 EN-GJS-700-2(GGG70), 0.8170 EN-GJMB-700-2(GTS70) 3.7024 Ti99,5, 3.7114 TiAl5Sn2,5, 3.7124 TiCu2 3.7154 TiAl6Zr5, 3.7165 TiAl6V4, 3.7184 TiAl4Mo4Sn2,5, - TiAl8Mo1V1 3.0255 Al99,5, 3.2315 AlMgSi1, 3.3515 AlMg1 3.0615 AlMgSiPb, 3.1325 AlCuMg1, 3.3245 AlMg3Si, 3.4365 AlZnMgCu1,5 3.2131 G-AlSi5Cu1, 3.2153 G-AlSi7Cu3, 3.2573 G-AlSi9 3.2581 G-AlSi12, 3.2583 G-AlSi12Cu, - G-AlSi12CuNiMg 3.5200 MgMn2, 3.5812.05 G-MgAl8Zn1, 3.5612.05 G-MgAl6Zn1 2.0070 SE-Cu, 2.1020 CuSn6, 2.1096 G-CuSn5ZnPb 2.0380 CuZn39Pb2, 2.0401 CuZn39Pb3, 2.0410 CuZn43Pb2 2.0250 CuZn20, 2.0280 CuZn33, 2.0332 CuZn37Pb0,5 2.1090 CuSn7ZnPb, 2.1170 CuPb5Sn5, 2.1176 CuPb10Sn 2.0790 CuNi18Zn19Pb 2.0916 CuAl5, 2.0960 CuAl9Mn, 2.1050 CuSn10 2.0980 CuAl11Ni, 2.1247 CuBe2 Bakelit, Resopal, Pertinax, Moltopren Plexiglass, Hostalen, Novodur, Makralon Kevlar GFK/CFK
Tensile strength Hardness MPa (N/mm2) 500 >500-850 850 850-1000 700 700-850 850-1000 850-1000 1000-1200 750 850-1000 1000-1200 850-1000 >1000-1200 850 >850-1000 650-1000 330 HB 850 850 850 40-48 HRC >48-60 HRC 1200 240 HB <300 HB 240 HB <300 HB 350 HB 850 >850-1200 400 450 600 600 450 400 600 600 600 >600-850 850 >850-1000
Coolant
bright
steam tempered
nitrided lands
nitrided
golden brown
TiAlN
72
GUHRINGGUIDE
Tool material Type Surface finish Internal cooling DIN 339 DIN 340 G.S. MT DIN 341 Std. range, page straight
HSCO
HSCO
Ti Ti
HSCO
GT 100
Carbide
K10/K20 N
GT 100
Guh. no.
311 317 357 364 374 462 374 336 623 462 374 374 374 403 617 669 396 706
vc m/min
24 24 16 16 12 14 10 12 8 16 8 8 6 12 8 10
5 5 4 4 3 4 3 4 3 4 3 3 2 4 3 3
5 4 4 3 4 3 4 3 4 3 3 4 3
2 2 5
7 6 7 6 6
5 5 6
80 70 80 70 80 70 60 60 80 60 50 50
15
3 49 19
7
5 5 4 5 4 3 5
13 10 10 10 8 15 10 13 3 6
3 3 3 3 4 16 10 24 10 10 7 14 10 12
3 3
1
2 3 3 1 1
4 4 4
5 30 24 24 20 6 8 5
1 6 6 6 6 3
6 6
6 3 6 10 6
2 2
7 6
3 2 2
49 38 38 30
7 7
7 7
60 50 30 38 30 24 24 20 16 5* 5* 4* 4* 4* 4* 4
94 76 49 61
8 7 6 6 5 5
5
5 5
4
4
25
38 30 24
25 25 25 25 20 10 15 90 80 80 70 10 20 15 200 200 150 120 180 80 180 180 120 120 70 50 50 40 150 80
4 3 3
AlTiN
TiCN
FIRE
AlCrN
TiN
MolyGlide
73
Twist Drills
If flute length permits, DIN 338 and DIN 345 can also be applied for holes 10 x D.
Twist Drills
Tools with bold feed column no. are preferred choice.
1
0.004 0.006 0.020 0.025 0.032 0.040 0.040 0.050 0.063 0.080 0.080 0.100 0.125 0.160 0.160 0.200 0.250 0.315 0.400
2
0.006 0.008 0.025 0.032 0.040 0.050 0.050 0.063 0.080 0.100 0.100 0.125 0.160 0.200 0.200 0.250 0.310 0.400 0.500
3
0.007 0.012 0.032 0.040 0.050 0.063 0.063 0.080 0.100 0.125 0.125 0.160 0.200 0.250 0.250 0.315 0.400 0.500 0.630
7
0.014 0.020 0.080 0.100 0.125 0.160 0.160 0.200 0.250 0.315 0.315 0.400 0.500 0.630 0.630 0.800 1.000 1.250 1.600
8
0.016 0.023 0.100 0.125 0.160 0.200 0.200 0.250 0.315 0.400 0.400 0.500 0.630 0.800 0.800 1.000 1.250 1.600 1.600
9
0.019 0.025 0.125 0.160 0.160 0.200 0.250 0.315 0.315 0.400 0.500 0.630 0.630 0.800 1.000 1.250 1.250 1.600 2.000
Cooling: without coolant ducts with coolant ducts Coolant: Air Neat oil Soluble oil Cutting direction: right-hand cutting left-hand cutting * Use bright finish drills or use drills with bright polished flutes.
Material group Common structural steels Free-cutting steels Unalloyed heat-treatable steels
Alloyed heat-treatable steels Unalloyed case hardened steels Alloyed case hardened steels Nitriding steels Tool steels High speed steels Spring steels Stainless steels, sulphured austenitic martensitic Hardened steels Special alloys Cast iron Spheroidal graphite iron and malleable cast iron Chilled cast iron Ti and Ti-alloys Aluminium and Al-alloys Al wrought alloys Al cast alloys 10 % Si > 10 % Si Magnesium alloys Copper, low-alloyed Brass, short-chipping long-chipping Bronze, short-chipping Bronze, long-chipping Duroplastics Thermoplastics Kevlar Glass, carbon concent. plastics
Material examples, new description (old description in brackets) Figures in bold = material no. to DIN EN 1.0035 S185(St33),1.0486 P275N(StE285),1.0345 P235GH(H1),1.0425 P265GH(H2) 1.0050 E295 (St50-2), 1.0070 E360 (St70-2), 1.8937 P500NH (WStE500) 1.0718 11SMnPb30 (9SMnPb28), 1.0736 11SMn37 (9SMn36) 1.0727 46S20 (45S20), 1.0728 (60S20), 1.0757 46SPb20 (45SPb20) 1.0402 C22, 1.1178 C30E (Ck30) 1.0503 C45, 1.1191 C45E (Ck45) 1.0601 C60, 1.1221 C60E (Ck60) 1.5131 50MnSi4, 1.7003 38Cr2, 1.7030 28Cr4 1.5710 36NiCr6, 1.7035 41Cr4, 1.7225 42CrMo4 1.0301 (C10), 1.1121 C10E (Ck10) 1.7043 38Cr4 1.5752 15NiCr13 (15NiCr13), 1.7131 16MnCr5, 1.7264 20CrMo5 1.8504 34CrAl6 1.8519 31CrMoV9, 1.8550 34CrAlNi7 1.1750 C75W, 1.2067 102Cr6, 1.2307 29CrMoV9 1.2080 X210Cr12, 1.2083 X42Cr13, 1.2419 105WCr6, 1.2767 X45NiCrMo4 1.3243 S 6-5-2-5, 1.3343 S 6-5-2, 1.3344 S 6-5-3 1.5026 55Si7, 1.7176 55Cr3, 1.8159 51CrV4 (51CrV4) 1.4005 X12CrS13, 1.4104 X14CrMoS17, 1.4105 X6CrMoS17, 1.4305 X8CrNiS18-9 1.4301 X5CrNi18-10 (V2A), 1.4541 X6CrNiTi18-10, 1.4571 X6CrNiMoTi 17-12-2 (V4A) 1.4057 X20CrNi 17 2 (X17CrNi16-2), 1.4122 X39CrMo17-1, 1.4521 X2CrMoTi18-2 Nimonic, Inconel, Monel, Hastelloy 0.6010 EN-GJL-100(GG10), 0.6020 EN-GJL-200(GG20) 0.6025 EN-GJL-250(GG25), 0.6035 EN-GJL-350(GG35) 0.7050 EN-GJS-500-7(GGG50), 0.8035 EN-GJMW-350-4(GTW35) 0.7070 EN-GJS-700-2(GGG70), 0.8170 EN-GJMB-700-2(GTS70) 3.7024 Ti99,5, 3.7114 TiAl5Sn2,5, 3.7124 TiCu2 3.7154 TiAl6Zr5, 3.7165 TiAl6V4, 3.7184 TiAl4Mo4Sn2,5, - TiAl8Mo1V1 3.0255 Al99,5, 3.2315 AlMgSi1, 3.3515 AlMg1 3.0615 AlMgSiPb, 3.1325 AlCuMg1, 3.3245 AlMg3Si, 3.4365 AlZnMgCu1,5 3.2131 G-AlSi5Cu1, 3.2153 G-AlSi7Cu3, 3.2573 G-AlSi9 3.2581 G-AlSi12, 3.2583 G-AlSi12Cu, - G-AlSi12CuNiMg 3.5200 MgMn2, 3.5812.05 G-MgAl8Zn1, 3.5612.05 G-MgAl6Zn1 2.0070 SE-Cu, 2.1020 CuSn6, 2.1096 G-CuSn5ZnPb 2.0380 CuZn39Pb2, 2.0401 CuZn39Pb3, 2.0410 CuZn43Pb2 2.0250 CuZn20, 2.0280 CuZn33, 2.0332 CuZn37Pb0,5 2.1090 CuSn7ZnPb, 2.1170 CuPb5Sn5, 2.1176 CuPb10Sn 2.0790 CuNi18Zn19Pb 2.0916 CuAl5, 2.0960 CuAl9Mn, 2.1050 CuSn10 2.0980 CuAl11Ni, 2.1247 CuBe2 Bakelit, Resopal, Pertinax, Moltopren Plexiglass, Hostalen, Novodur, Makralon Kevlar GFK/CFK
Tensile strength Hardness MPa (N/mm2) 500 >500-850 850 850-1000 700 700-850 850-1000 850-1000 1000-1200 750 850-1000 1000-1200 850-1000 >1000-1200 850 >850-1000 650-1000 330 HB 850 850 850 40-48 HRC >48-60 HRC 1200 240 HB <300 HB 240 HB <300 HB 350 HB 850 >850-1200 400 450 600 600 450 400 600 600 600 >600-850 850 >850-1000
Coolant
bright
steam tempered
nitrided lands
nitrided
golden brown
TiAlN
74
GUHRINGGUIDE
HSCO
HSCO
HSCO
GT 100
GT 100
GT 100
618, 619
1 2
Guh. no. MT
620, 621
3
4
473
476
vc m/min
vc m/min 45 34 45 34 45 34 28 22 16 45 20 14 16 12 20 12 12 8 16 12 14 4 8 45 34 38 28 8 12 8
vc m/min 30 25 30 25 30 25 18 16 12 30 14 12 12 8 16 8 8 6 12 8 12 3 6 30 25 28 20 6 8 6
20
4 3 3 2 3 2 3 2 3 2 2 1 3 2
1 2
14 14 10 12 10 10 8 14 8 8 6 10 8 10 3 6 20 16 6 8 6
4 4 3 4 3 4 3 3 3 2 4 3
2 3 4 6
5 4 5 4 4 4 3 3 2 5 3 2 3 2 3 2 2 2 3 2 1 1 5 5 5 5 2 2 2 6* 5* 4* 4* 4* 4* 4* 4*
2
1 5 5 1 1
6 5 4 4 2
1 6 6 2 2
7* 6* 5* 5* 4* 3 6 6
50 40 24 30
85 75 45 55 34 34 28 34
63 50 30 40 28 25 20 25
20 16 14
3
3
4* 4*
5*
10
AlTiN
TiCN
FIRE
AlCrN
TiN
MolyGlide
75
Twist Drills
If flute length permits, DIN 338 and DIN 345 can also be applied for holes 10 x D.
Micro-Precision Tools
Tools with bold feed column no. are preferred choice.
Twist Drills
Attention! Special table with feed column nos for micro-precision drills.
Drill mm 0.10 0.16 0.25 0.30 0.50 0.63 0.80 1.00 1.50 2.00
1
0.002 0.002 0.003 0.004 0.005 0.007 0.010 0.020 0.030 0.040
9
0.016 0.022 0.024 0.033 0.041 0.057 0.060 0.086 0.092 0.122
Cooling: without coolant ducts with coolant ducts Coolant: Air Neat oil Soluble oil Cutting direction: right-hand cutting left-hand cutting
Material group Common structural steels Free-cutting steels Unalloyed heat-treatable steels
Alloyed heat-treatable steels Unalloyed case hardened steels Alloyed case hardened steels Nitriding steels Tool steels High speed steels Spring steels Stainless steels, sulphured austenitic martensitic Hardened steels Special alloys Cast iron Spheroidal graphite iron and malleable cast iron Chilled cast iron Ti and Ti-alloys Aluminium and Al-alloys Al wrought alloys Al cast alloys 10 % Si > 10 % Si Magnesium alloys Copper, low-alloyed Brass, short-chipping long-chipping Bronze, short-chipping Bronze, long-chipping Duroplastics Thermoplastics Kevlar Glass, carbon concent. plastics
Material examples, new description (old description in brackets) Figures in bold = material no. to DIN EN 1.0035 S185(St33),1.0486 P275N(StE285),1.0345 P235GH(H1),1.0425 P265GH(H2) 1.0050 E295 (St50-2), 1.0070 E360 (St70-2), 1.8937 P500NH (WStE500) 1.0718 11SMnPb30 (9SMnPb28), 1.0736 11SMn37 (9SMn36) 1.0727 46S20 (45S20), 1.0728 (60S20), 1.0757 46SPb20 (45SPb20) 1.0402 C22, 1.1178 C30E (Ck30) 1.0503 C45, 1.1191 C45E (Ck45) 1.0601 C60, 1.1221 C60E (Ck60) 1.5131 50MnSi4, 1.7003 38Cr2, 1.7030 28Cr4 1.5710 36NiCr6, 1.7035 41Cr4, 1.7225 42CrMo4 1.0301 (C10), 1.1121 C10E (Ck10) 1.7043 38Cr4 1.5752 15NiCr13 (15NiCr13), 1.7131 16MnCr5, 1.7264 20CrMo5 1.8504 34CrAl6 1.8519 31CrMoV9, 1.8550 34CrAlNi7 1.1750 C75W, 1.2067 102Cr6, 1.2307 29CrMoV9 1.2080 X210Cr12, 1.2083 X42Cr13, 1.2419 105WCr6, 1.2767 X45NiCrMo4 1.3243 S 6-5-2-5, 1.3343 S 6-5-2, 1.3344 S 6-5-3 1.5026 55Si7, 1.7176 55Cr3, 1.8159 51CrV4 (51CrV4) 1.4005 X12CrS13, 1.4104 X14CrMoS17, 1.4105 X6CrMoS17, 1.4305 X8CrNiS18-9 1.4301 X5CrNi18-10 (V2A), 1.4541 X6CrNiTi18-10, 1.4571 X6CrNiMoTi 17-12-2 (V4A) 1.4057 X20CrNi 17 2 (X17CrNi16-2), 1.4122 X39CrMo17-1, 1.4521 X2CrMoTi18-2 Nimonic, Inconel, Monel, Hastelloy 0.6010 EN-GJL-100(GG10), 0.6020 EN-GJL-200(GG20) 0.6025 EN-GJL-250(GG25), 0.6035 EN-GJL-350(GG35) 0.7050 EN-GJS-500-7(GGG50), 0.8035 EN-GJMW-350-4(GTW35) 0.7070 EN-GJS-700-2(GGG70), 0.8170 EN-GJMB-700-2(GTS70) 3.7024 Ti99,5, 3.7114 TiAl5Sn2,5, 3.7124 TiCu2 3.7154 TiAl6Zr5, 3.7165 TiAl6V4, 3.7184 TiAl4Mo4Sn2,5, - TiAl8Mo1V1 3.0255 Al99,5, 3.2315 AlMgSi1, 3.3515 AlMg1 3.0615 AlMgSiPb, 3.1325 AlCuMg1, 3.3245 AlMg3Si, 3.4365 AlZnMgCu1,5 3.2131 G-AlSi5Cu1, 3.2153 G-AlSi7Cu3, 3.2573 G-AlSi9 3.2581 G-AlSi12, 3.2583 G-AlSi12Cu, - G-AlSi12CuNiMg 3.5200 MgMn2, 3.5812.05 G-MgAl8Zn1, 3.5612.05 G-MgAl6Zn1 2.0070 SE-Cu, 2.1020 CuSn6, 2.1096 G-CuSn5ZnPb 2.0380 CuZn39Pb2, 2.0401 CuZn39Pb3, 2.0410 CuZn43Pb2 2.0250 CuZn20, 2.0280 CuZn33, 2.0332 CuZn37Pb0,5 2.1090 CuSn7ZnPb, 2.1170 CuPb5Sn5, 2.1176 CuPb10Sn 2.0790 CuNi18Zn19Pb 2.0916 CuAl5, 2.0960 CuAl9Mn, 2.1050 CuSn10 2.0980 CuAl11Ni, 2.1247 CuBe2 Bakelit, Resopal, Pertinax, Moltopren Plexiglass, Hostalen, Novodur, Makralon Kevlar GFK/CFK
Tensile strength Hardness MPa (N/mm2) 500 >500-850 850 850-1000 700 700-850 850-1000 850-1000 1000-1200 750 850-1000 1000-1200 850-1000 >1000-1200 850 >850-1000 650-1000 330 HB 850 850 850 40-48 HRC >48-60 HRC 1200 240 HB <300 HB 240 HB <300 HB 350 HB 850 >850-1200 400 450 600 600 450 400 600 600 600 >600-850 850 >850-1000
Coolant
bright
steam tempered
nitrided lands
nitrided
golden brown
TiAlN
76
GUHRINGGUIDE
Tool material Carbide grade Type Surface finish Guh. no. straight shank DIN 1899 G.S. Std. range, page
HSCO
N 301 303 350
HSCO
N 660
Carbide
K10/K20 N
350
701 350
vc m/min 21 18 18 16 20 18 14 14 12 18 14 12 14 12 16 14 14 8 6 6 6
vc m/min 27 23 23 21 26 23 18 18 16 23 18 16 18 16 20 18 18 10 8 8 8
vc m/min 50 35 50 45 45 35 30 30 50 40 25 25
1,5
5 4
4 4 3 3 3 3 3 3
4 4 4 4 4
3 3 2 4 3 3 3 3 3 6
4 4 4 4 4
3 3 2 4 3 3 3 3 3 6
3 2 2
4
26 22 18 22
6 6
6
33 28 23 28
6 6
6
3 5 5 5 4 4 7 6 6 6 5 5
6 4 3 3 3 3 3 3 4 5
l = 6,8mm
l = 3,4mm
26 18 75 42
7 6 6 5 5 4 4 4 4 4
33 23 97 53 28 28 23 16 14 20 23
7 6 6 5 5 4 4 4 4 4 4
l = 0,5mm
3xD
22 22 18 13 16 18
0,1
0,5
1,0
AlTiN
TiCN
FIRE
AlCrN
TiN
MolyGlide
77
Twist Drills
Ratio Drills
Tools with bold feed column no. are preferred choice.
Twist Drills
Drill mm 0.50 1.00 2.00 2.50 3.15 4.00 5.00 6.30 8.00 10.00 12.50 16.00 20.00 25.00 31.50 40.00 50.00 63.00 80.00
1
0.004 0.006 0.020 0.025 0.032 0.040 0.040 0.050 0.063 0.080 0.080 0.100 0.125 0.160 0.160 0.200 0.250 0.315 0.400
2
0.006 0.008 0.025 0.032 0.040 0.050 0.050 0.063 0.080 0.100 0.100 0.125 0.160 0.200 0.200 0.250 0.310 0.400 0.500
3
0.007 0.012 0.032 0.040 0.050 0.063 0.063 0.080 0.100 0.125 0.125 0.160 0.200 0.250 0.250 0.315 0.400 0.500 0.630
7
0.014 0.020 0.080 0.100 0.125 0.160 0.160 0.200 0.250 0.315 0.315 0.400 0.500 0.630 0.630 0.800 1.000 1.250 1.600
8
0.016 0.023 0.100 0.125 0.160 0.200 0.200 0.250 0.315 0.400 0.400 0.500 0.630 0.800 0.800 1.000 1.250 1.600 1.600
9
0.019 0.025 0.125 0.160 0.160 0.200 0.250 0.315 0.315 0.400 0.500 0.630 0.630 0.800 1.000 1.250 1.250 1.600 2.000
Cooling: without coolant ducts with coolant ducts Coolant: Air Neat oil Soluble oil Cutting direction: right-hand cutting left-hand cutting
Material group Common structural steels Free-cutting steels Unalloyed heat-treatable steels
Alloyed heat-treatable steels Unalloyed case hardened steels Alloyed case hardened steels Nitriding steels Tool steels High speed steels Spring steels Stainless steels, sulphured austenitic martensitic Hardened steels Special alloys Cast iron Spheroidal graphite iron and malleable cast iron Chilled cast iron Ti and Ti-alloys Aluminium and Al-alloys Al wrought alloys Al cast alloys 10 % Si > 10 % Si Magnesium alloys Copper, low-alloyed Brass, short-chipping long-chipping Bronze, short-chipping Bronze, long-chipping Duroplastics Thermoplastics Kevlar Glass, carbon concent. plastics
Material examples, new description (old description in brackets) Figures in bold = material no. to DIN EN 1.0035 S185(St33),1.0486 P275N(StE285),1.0345 P235GH(H1),1.0425 P265GH(H2) 1.0050 E295 (St50-2), 1.0070 E360 (St70-2), 1.8937 P500NH (WStE500) 1.0718 11SMnPb30 (9SMnPb28), 1.0736 11SMn37 (9SMn36) 1.0727 46S20 (45S20), 1.0728 (60S20), 1.0757 46SPb20 (45SPb20) 1.0402 C22, 1.1178 C30E (Ck30) 1.0503 C45, 1.1191 C45E (Ck45) 1.0601 C60, 1.1221 C60E (Ck60) 1.5131 50MnSi4, 1.7003 38Cr2, 1.7030 28Cr4 1.5710 36NiCr6, 1.7035 41Cr4, 1.7225 42CrMo4 1.0301 (C10), 1.1121 C10E (Ck10) 1.7043 38Cr4 1.5752 15NiCr13 (15NiCr13), 1.7131 16MnCr5, 1.7264 20CrMo5 1.8504 34CrAl6 1.8519 31CrMoV9, 1.8550 34CrAlNi7 1.1750 C75W, 1.2067 102Cr6, 1.2307 29CrMoV9 1.2080 X210Cr12, 1.2083 X42Cr13, 1.2419 105WCr6, 1.2767 X45NiCrMo4 1.3243 S 6-5-2-5, 1.3343 S 6-5-2, 1.3344 S 6-5-3 1.5026 55Si7, 1.7176 55Cr3, 1.8159 51CrV4 (51CrV4) 1.4005 X12CrS13, 1.4104 X14CrMoS17, 1.4105 X6CrMoS17, 1.4305 X8CrNiS18-9 1.4301 X5CrNi18-10 (V2A), 1.4541 X6CrNiTi18-10, 1.4571 X6CrNiMoTi 17-12-2 (V4A) 1.4057 X20CrNi 17 2 (X17CrNi16-2), 1.4122 X39CrMo17-1, 1.4521 X2CrMoTi18-2 Nimonic, Inconel, Monel, Hastelloy 0.6010 EN-GJL-100(GG10), 0.6020 EN-GJL-200(GG20) 0.6025 EN-GJL-250(GG25), 0.6035 EN-GJL-350(GG35) 0.7050 EN-GJS-500-7(GGG50), 0.8035 EN-GJMW-350-4(GTW35) 0.7070 EN-GJS-700-2(GGG70), 0.8170 EN-GJMB-700-2(GTS70) 3.7024 Ti99,5, 3.7114 TiAl5Sn2,5, 3.7124 TiCu2 3.7154 TiAl6Zr5, 3.7165 TiAl6V4, 3.7184 TiAl4Mo4Sn2,5, - TiAl8Mo1V1 3.0255 Al99,5, 3.2315 AlMgSi1, 3.3515 AlMg1 3.0615 AlMgSiPb, 3.1325 AlCuMg1, 3.3245 AlMg3Si, 3.4365 AlZnMgCu1,5 3.2131 G-AlSi5Cu1, 3.2153 G-AlSi7Cu3, 3.2573 G-AlSi9 3.2581 G-AlSi12, 3.2583 G-AlSi12Cu, - G-AlSi12CuNiMg 3.5200 MgMn2, 3.5812.05 G-MgAl8Zn1, 3.5612.05 G-MgAl6Zn1 2.0070 SE-Cu, 2.1020 CuSn6, 2.1096 G-CuSn5ZnPb 2.0380 CuZn39Pb2, 2.0401 CuZn39Pb3, 2.0410 CuZn43Pb2 2.0250 CuZn20, 2.0280 CuZn33, 2.0332 CuZn37Pb0,5 2.1090 CuSn7ZnPb, 2.1170 CuPb5Sn5, 2.1176 CuPb10Sn 2.0790 CuNi18Zn19Pb 2.0916 CuAl5, 2.0960 CuAl9Mn, 2.1050 CuSn10 2.0980 CuAl11Ni, 2.1247 CuBe2 Bakelit, Resopal, Pertinax, Moltopren Plexiglass, Hostalen, Novodur, Makralon Kevlar GFK/CFK
Tensile strength Hardness MPa (N/mm2) 500 >500-850 850 850-1000 700 700-850 850-1000 850-1000 1000-1200 750 850-1000 1000-1200 850-1000 >1000-1200 850 >850-1000 650-1000 330 HB 850 850 850 40-48 HRC >48-60 HRC 1200 240 HB <300 HB 240 HB <300 HB 350 HB 850 >850-1200 400 450 600 600 450 400 600 600 600 >600-850 850 >850-1000
Coolant
bright
steam tempered
nitrided lands
nitrided
golden brown
TiAlN
78
GUHRINGGUIDE
Tool material Carb. head Carbide grade P Type RT 80 U Surface finish Cooling HA DIN 6537 HE DIN 6538 HE 1171 DIN 6539 DZ Std. range, page 543
K RT 100 G
K/P RT 100 F
K/P RT 100 U
Guh. no.
1661
510
510
511
511
511
511
511
vc m/min 95 80 95 75 80 75 70 75 60 90 75 60 75 60 45 35 40 40 35 35
vc m/min
vc vc m/min m/min 110 90 130 110 100 95 90 90 80 110 90 65 85 80 60 50 45 45 45 40 35 40 25 25 160 120 100 95 30 35 30 240 240 220 170 230 95 250 170 95 80 70 60 145 120 170 145 130 125 120 120 105 145 120 85 110 105 80 65 60 60 60 55 45 55 35 35 195 160 140 130 40 45 40 310 310 260 220 280 125 325 220 125 105 90 80 6 5 7 7 7 6 6 6 6 7 6 4 6 6 5 7 7 7 6 6 6 6 7 6 4 6 7 6 8 8 8 7 7 7 7 8 7 5 7
7 7 7 6
6 6 6 6 2
7 7
4 5 4 3 2 4 4 4 2 1 3
8 8 8 7 2
4 5 4 3 2 4 4 4 2 1 3
8 8 8 7 2
5 6 5 4 3 5 5 5 3 2 4
9 9 9 8 3
6 5 7 7 7 6 6 6 6 7 6 4 6
5 5 4 2 4 4 4 2 1 3
7 6 8 8 8 7 7 7 7 8 7 5 7
5 6 5 3 5 5 5 3 2 4
6 5 7 7 7 6 6 6 6 7 6 4 6
5 5 4 2 4 4 4 2 1 3
7 6 8 8 8 7 7 7 7 8 7 5 7
5 6 5 3 5 5 5 3 2 4
8 8 8 7
8 6 6
5 6 5 5 4 3
3 2 8 8 8 8
7
3 2 8 8 8 8
7
4 3 9 9 9 9
8
8 8 8 7 2
3 2 8 8 8 8 6 7
9 9 9 8 3
4 3 9 9 9 9 7 8
8 8 8 7 2
3 2 8 8 8 8 6 7
9 9 9 8 3
4 3 9 9 9 9 7 8
6 7
6 6 5 5 5
6 7
6 6 5 5 5
7 8
7 7 6 6 6
7 6 6 5 5 5
8 7 7 6 6 6
7 6 6 5 5 5
8 7 7 6 6 6
AlTiN
TiCN
FIRE
AlCrN
TiN
MolyGlide
79
Twist Drills
Carbide
Ratio Drills
Tools with bold feed column no. are preferred choice.
Twist Drills
Drill mm 0.50 1.00 2.00 2.50 3.15 4.00 5.00 6.30 8.00 10.00 12.50 16.00 20.00 25.00 31.50 40.00 50.00 63.00 80.00
1
0.004 0.006 0.020 0.025 0.032 0.040 0.040 0.050 0.063 0.080 0.080 0.100 0.125 0.160 0.160 0.200 0.250 0.315 0.400
2
0.006 0.008 0.025 0.032 0.040 0.050 0.050 0.063 0.080 0.100 0.100 0.125 0.160 0.200 0.200 0.250 0.310 0.400 0.500
3
0.007 0.012 0.032 0.040 0.050 0.063 0.063 0.080 0.100 0.125 0.125 0.160 0.200 0.250 0.250 0.315 0.400 0.500 0.630
7
0.014 0.020 0.080 0.100 0.125 0.160 0.160 0.200 0.250 0.315 0.315 0.400 0.500 0.630 0.630 0.800 1.000 1.250 1.600
8
0.016 0.023 0.100 0.125 0.160 0.200 0.200 0.250 0.315 0.400 0.400 0.500 0.630 0.800 0.800 1.000 1.250 1.600 1.600
9
0.019 0.025 0.125 0.160 0.160 0.200 0.250 0.315 0.315 0.400 0.500 0.630 0.630 0.800 1.000 1.250 1.250 1.600 2.000
Cooling: without coolant ducts with coolant ducts Coolant: Air Neat oil Soluble oil Cutting direction: right-hand cutting left-hand cutting Al especially suitable for machining aluminium G especially suitable for machining cast iron
Material group Common structural steels Free-cutting steels Unalloyed heat-treatable steels
Alloyed heat-treatable steels Unalloyed case hardened steels Alloyed case hardened steels Nitriding steels Tool steels High speed steels Spring steels Stainless steels, sulphured austenitic martensitic Hardened steels Special alloys Cast iron Spheroidal graphite iron and malleable cast iron Chilled cast iron Ti and Ti-alloys Aluminium and Al-alloys Al wrought alloys Al cast alloys 10 % Si > 10 % Si Magnesium alloys Copper, low-alloyed Brass, short-chipping long-chipping Bronze, short-chipping Bronze, long-chipping Duroplastics Thermoplastics Kevlar Glass, carbon concent. plastics
Material examples, new description (old description in brackets) Figures in bold = material no. to DIN EN 1.0035 S185(St33),1.0486 P275N(StE285),1.0345 P235GH(H1),1.0425 P265GH(H2) 1.0050 E295 (St50-2), 1.0070 E360 (St70-2), 1.8937 P500NH (WStE500) 1.0718 11SMnPb30 (9SMnPb28), 1.0736 11SMn37 (9SMn36) 1.0727 46S20 (45S20), 1.0728 (60S20), 1.0757 46SPb20 (45SPb20) 1.0402 C22, 1.1178 C30E (Ck30) 1.0503 C45, 1.1191 C45E (Ck45) 1.0601 C60, 1.1221 C60E (Ck60) 1.5131 50MnSi4, 1.7003 38Cr2, 1.7030 28Cr4 1.5710 36NiCr6, 1.7035 41Cr4, 1.7225 42CrMo4 1.0301 (C10), 1.1121 C10E (Ck10) 1.7043 38Cr4 1.5752 15NiCr13 (15NiCr13), 1.7131 16MnCr5, 1.7264 20CrMo5 1.8504 34CrAl6 1.8519 31CrMoV9, 1.8550 34CrAlNi7 1.1750 C75W, 1.2067 102Cr6, 1.2307 29CrMoV9 1.2080 X210Cr12, 1.2083 X42Cr13, 1.2419 105WCr6, 1.2767 X45NiCrMo4 1.3243 S 6-5-2-5, 1.3343 S 6-5-2, 1.3344 S 6-5-3 1.5026 55Si7, 1.7176 55Cr3, 1.8159 51CrV4 (51CrV4) 1.4005 X12CrS13, 1.4104 X14CrMoS17, 1.4105 X6CrMoS17, 1.4305 X8CrNiS18-9 1.4301 X5CrNi18-10 (V2A), 1.4541 X6CrNiTi18-10, 1.4571 X6CrNiMoTi 17-12-2 (V4A) 1.4057 X20CrNi 17 2 (X17CrNi16-2), 1.4122 X39CrMo17-1, 1.4521 X2CrMoTi18-2 Nimonic, Inconel, Monel, Hastelloy 0.6010 EN-GJL-100(GG10), 0.6020 EN-GJL-200(GG20) 0.6025 EN-GJL-250(GG25), 0.6035 EN-GJL-350(GG35) 0.7050 EN-GJS-500-7(GGG50), 0.8035 EN-GJMW-350-4(GTW35) 0.7070 EN-GJS-700-2(GGG70), 0.8170 EN-GJMB-700-2(GTS70) 3.7024 Ti99,5, 3.7114 TiAl5Sn2,5, 3.7124 TiCu2 3.7154 TiAl6Zr5, 3.7165 TiAl6V4, 3.7184 TiAl4Mo4Sn2,5, - TiAl8Mo1V1 3.0255 Al99,5, 3.2315 AlMgSi1, 3.3515 AlMg1 3.0615 AlMgSiPb, 3.1325 AlCuMg1, 3.3245 AlMg3Si, 3.4365 AlZnMgCu1,5 3.2131 G-AlSi5Cu1, 3.2153 G-AlSi7Cu3, 3.2573 G-AlSi9 3.2581 G-AlSi12, 3.2583 G-AlSi12Cu, - G-AlSi12CuNiMg 3.5200 MgMn2, 3.5812.05 G-MgAl8Zn1, 3.5612.05 G-MgAl6Zn1 2.0070 SE-Cu, 2.1020 CuSn6, 2.1096 G-CuSn5ZnPb 2.0380 CuZn39Pb2, 2.0401 CuZn39Pb3, 2.0410 CuZn43Pb2 2.0250 CuZn20, 2.0280 CuZn33, 2.0332 CuZn37Pb0,5 2.1090 CuSn7ZnPb, 2.1170 CuPb5Sn5, 2.1176 CuPb10Sn 2.0790 CuNi18Zn19Pb 2.0916 CuAl5, 2.0960 CuAl9Mn, 2.1050 CuSn10 2.0980 CuAl11Ni, 2.1247 CuBe2 Bakelit, Resopal, Pertinax, Moltopren Plexiglass, Hostalen, Novodur, Makralon Kevlar GFK/CFK
Tensile strength Hardness MPa (N/mm2) 500 >500-850 850 850-1000 700 700-850 850-1000 850-1000 1000-1200 750 850-1000 1000-1200 850-1000 >1000-1200 850 >850-1000 650-1000 330 HB 850 850 850 40-48 HRC >48-60 HRC 1200 240 HB <300 HB 240 HB <300 HB 350 HB 850 >850-1200 400 450 600 600 450 400 600 600 600 >600-850 850 >850-1000
Coolant
bright
steam tempered
nitrided lands
nitrided
golden brown
TiAlN
80
GUHRINGGUIDE
Tool material Carbide grade Type Surface finish Cooling HA DIN 6537 HE DIN 6538 HE DIN 6539 DZ G.S. HA Std. range, page
K/P RT 100 F
K/P RT 100 U
K RT 150 GG
Guhring no.
1659
2475
1673
2480 1184 2472 1242 2473 503 768 535 6068 535
503
Al
vc vc m/min m/min 100 85 110 85 90 85 80 80 75 100 90 65 75 70 50 40 40 45 40 35 35 35 20 20 160 120 120 95 25 30 25 200 200 170 140 200 80 210 140 80 65 60 45 130 110 145 110 120 110 105 105 100 130 120 85 100 90 65 55 55 45 55 45 45 45 25 25 210 155 155 125 35 40 35 260 260 220 180 260 105 270 180 105 85 80 60 6 5 7 6 6 6 6 6 5 7 6 4 5 7 6 8 7 7 7 7 7 6 8 7 5 6 6 5 7 6 6 6 6 6 5 7 6 4 5
vc m/min
4 5 4 3 2 3 3 2 2 1 3
7 7 6 6 2
5 6 5 4 3 4 4 3 3 2 4
8 8 7 7 3
4 5 4 3 2 3 3 2 2 1 3
7 7 6 6 2
6 5 7 6 6 6 6 6 5 7 6 4 5
4 5 4 2 3 3 2 2 1 3
7 6 8 7 7 7 7 7 6 8 7 5 6
5 6 5 3 4 4 3 3 2 4
6 5 7 6 6 6 6 6 5 7 6 4 5
4 5 4 2 3 3 2 2 1 3
7 6 8 7 7 7 7 7 6 8 7 5 6
5 6 5 3 4 4 3 3 2 4
6 5 7 6 6 6 6 6 5 7 6 4 5
4 5 4 2 3 3 2 2 1 3
7 6 8 7 7 7 7 7 6 8 7 5 6
5 6 5 3 4 4 3 3 2 4
2 2 8 8 8 7 6 7
6 5 5 4 4 7
3 3 9 9 9 8 7 8
7 6 6 5 5 8
2 2 8 8 8 7 6 7
6 5 5 4 4 7
7 7 6 6 2
3 2 8 8 8 7 6 7
8 8 7 7 3
4 3 9 9 9 8 7 8
7 7 6 6 2
3 2 8 8 8 7 6 7
8 8 7 7 3
4 3 9 9 9 8 7 8
7 7 6 6 2
3 2 8 8 8 7 6 7
8 8 7 7 3
4 3 9 9 9 8 7 8
120 100 90 80 40
7 7 7 7 2
7 7 7 7 2
7 7 7 7
7 6 5 5 4 4
8 7 6 6 5 5
7 6 5 5 4 4
8 7 6 6 5 5
7 6 5 5 4 4
8 7 6 6 5 5
9 9 9 9
9 6 5
280 110 80
9 6 5
AlTiN
TiCN
FIRE
AlCrN
TiN
MolyGlide
81
Twist Drills
3D drilling depth
Carbide
4D
Carbide
Ratio Drills
Tools with bold feed column no. are preferred choice.
Twist Drills
Drill mm 0.50 1.00 2.00 2.50 3.15 4.00 5.00 6.30 8.00 10.00 12.50 16.00 20.00 25.00 31.50 40.00 50.00 63.00 80.00
1
0.004 0.006 0.020 0.025 0.032 0.040 0.040 0.050 0.063 0.080 0.080 0.100 0.125 0.160 0.160 0.200 0.250 0.315 0.400
2
0.006 0.008 0.025 0.032 0.040 0.050 0.050 0.063 0.080 0.100 0.100 0.125 0.160 0.200 0.200 0.250 0.310 0.400 0.500
3
0.007 0.012 0.032 0.040 0.050 0.063 0.063 0.080 0.100 0.125 0.125 0.160 0.200 0.250 0.250 0.315 0.400 0.500 0.630
7
0.014 0.020 0.080 0.100 0.125 0.160 0.160 0.200 0.250 0.315 0.315 0.400 0.500 0.630 0.630 0.800 1.000 1.250 1.600
8
0.016 0.023 0.100 0.125 0.160 0.200 0.200 0.250 0.315 0.400 0.400 0.500 0.630 0.800 0.800 1.000 1.250 1.600 1.600
9
0.019 0.025 0.125 0.160 0.160 0.200 0.250 0.315 0.315 0.400 0.500 0.630 0.630 0.800 1.000 1.250 1.250 1.600 2.000
Cooling: without coolant ducts with coolant ducts Coolant: Air Neat oil Soluble oil Cutting direction: right-hand cutting left-hand cutting
Material group Common structural steels Free-cutting steels Unalloyed heat-treatable steels
Alloyed heat-treatable steels Unalloyed case hardened steels Alloyed case hardened steels Nitriding steels Tool steels High speed steels Spring steels Stainless steels, sulphured austenitic martensitic Hardened steels Special alloys Cast iron Spheroidal graphite iron and malleable cast iron Chilled cast iron Ti and Ti-alloys Aluminium and Al-alloys Al wrought alloys Al cast alloys 10 % Si > 10 % Si Magnesium alloys Copper, low-alloyed Brass, short-chipping long-chipping Bronze, short-chipping Bronze, long-chipping Duroplastics Thermoplastics Kevlar Glass, carbon concent. plastics
Material examples, new description (old description in brackets) Figures in bold = material no. to DIN EN 1.0035 S185(St33),1.0486 P275N(StE285),1.0345 P235GH(H1),1.0425 P265GH(H2) 1.0050 E295 (St50-2), 1.0070 E360 (St70-2), 1.8937 P500NH (WStE500) 1.0718 11SMnPb30 (9SMnPb28), 1.0736 11SMn37 (9SMn36) 1.0727 46S20 (45S20), 1.0728 (60S20), 1.0757 46SPb20 (45SPb20) 1.0402 C22, 1.1178 C30E (Ck30) 1.0503 C45, 1.1191 C45E (Ck45) 1.0601 C60, 1.1221 C60E (Ck60) 1.5131 50MnSi4, 1.7003 38Cr2, 1.7030 28Cr4 1.5710 36NiCr6, 1.7035 41Cr4, 1.7225 42CrMo4 1.0301 (C10), 1.1121 C10E (Ck10) 1.7043 38Cr4 1.5752 15NiCr13 (15NiCr13), 1.7131 16MnCr5, 1.7264 20CrMo5 1.8504 34CrAl6 1.8519 31CrMoV9, 1.8550 34CrAlNi7 1.1750 C75W, 1.2067 102Cr6, 1.2307 29CrMoV9 1.2080 X210Cr12, 1.2083 X42Cr13, 1.2419 105WCr6, 1.2767 X45NiCrMo4 1.3243 S 6-5-2-5, 1.3343 S 6-5-2, 1.3344 S 6-5-3 1.5026 55Si7, 1.7176 55Cr3, 1.8159 51CrV4 (51CrV4) 1.4005 X12CrS13, 1.4104 X14CrMoS17, 1.4105 X6CrMoS17, 1.4305 X8CrNiS18-9 1.4301 X5CrNi18-10 (V2A), 1.4541 X6CrNiTi18-10, 1.4571 X6CrNiMoTi 17-12-2 (V4A) 1.4057 X20CrNi 17 2 (X17CrNi16-2), 1.4122 X39CrMo17-1, 1.4521 X2CrMoTi18-2 Nimonic, Inconel, Monel, Hastelloy 0.6010 EN-GJL-100(GG10), 0.6020 EN-GJL-200(GG20) 0.6025 EN-GJL-250(GG25), 0.6035 EN-GJL-350(GG35) 0.7050 EN-GJS-500-7(GGG50), 0.8035 EN-GJMW-350-4(GTW35) 0.7070 EN-GJS-700-2(GGG70), 0.8170 EN-GJMB-700-2(GTS70) 3.7024 Ti99,5, 3.7114 TiAl5Sn2,5, 3.7124 TiCu2 3.7154 TiAl6Zr5, 3.7165 TiAl6V4, 3.7184 TiAl4Mo4Sn2,5, - TiAl8Mo1V1 3.0255 Al99,5, 3.2315 AlMgSi1, 3.3515 AlMg1 3.0615 AlMgSiPb, 3.1325 AlCuMg1, 3.3245 AlMg3Si, 3.4365 AlZnMgCu1,5 3.2131 G-AlSi5Cu1, 3.2153 G-AlSi7Cu3, 3.2573 G-AlSi9 3.2581 G-AlSi12, 3.2583 G-AlSi12Cu, - G-AlSi12CuNiMg 3.5200 MgMn2, 3.5812.05 G-MgAl8Zn1, 3.5612.05 G-MgAl6Zn1 2.0070 SE-Cu, 2.1020 CuSn6, 2.1096 G-CuSn5ZnPb 2.0380 CuZn39Pb2, 2.0401 CuZn39Pb3, 2.0410 CuZn43Pb2 2.0250 CuZn20, 2.0280 CuZn33, 2.0332 CuZn37Pb0,5 2.1090 CuSn7ZnPb, 2.1170 CuPb5Sn5, 2.1176 CuPb10Sn 2.0790 CuNi18Zn19Pb 2.0916 CuAl5, 2.0960 CuAl9Mn, 2.1050 CuSn10 2.0980 CuAl11Ni, 2.1247 CuBe2 Bakelit, Resopal, Pertinax, Moltopren Plexiglass, Hostalen, Novodur, Makralon Kevlar GFK/CFK
Tensile strength Hardness MPa (N/mm2) 500 >500-850 850 850-1000 700 700-850 850-1000 850-1000 1000-1200 750 850-1000 1000-1200 850-1000 >1000-1200 850 >850-1000 650-1000 330 HB 850 850 850 40-48 HRC >48-60 HRC 1200 240 HB <300 HB 240 HB <300 HB 350 HB 850 >850-1200 400 450 600 600 450 400 600 600 600 >600-850 850 >850-1000
Coolant
bright
steam tempered
nitrided lands
nitrided
golden brown
TiAlN
82
GUHRINGGUIDE
Tool material Carb.tipped Carbide grade P Type RT 80 U Surface finish Cooling HA DIN 6537 HE DIN 6538 HE 1172 G.S. DZ Std. range, page 546
K RT 100 G
K/P RT 100 F
K/P RT 100 U
Guh. no.
1662
1663
1799 507
520
521
520
520
521
521
521
521
vc m/min 95 80 95 75 80 80 75 75 55 90 75 55 70 55 40 35 40 40 35 35
vc vc m/min m/min 110 90 130 110 100 95 90 90 80 110 90 65 85 80 60 50 45 45 45 40 35 40 25 25 160 120 100 95 30 35 30 240 240 220 170 230 95 250 170 95 80 70 60 145 120 170 145 130 125 120 120 105 145 120 85 110 105 80 65 60 60 60 55 45 55 35 35 210 160 140 130 40 45 40 310 310 260 220 280 125 325 220 125 105 90 80 6 5 7 7 7 6 6 6 6 7 6 4 6 7 6 8 8 8 7 7 7 7 8 7 5 7 6 5 7 7 7 6 6 6 6 7 6 4 6
6 6 6 5
6 6 6 6 2
7 7
4 5 4 3 2 4 4 4 2 1 3
8 8 8 7 2
5 6 5 4 3 5 5 5 3 2 4
9 9 9 8 3
4 5 4 3 2 4 4 4 2 1 3
8 8 8 7 2
5 6 5 4 3 5 5 5 3 2 4
9 9 9 8 3
6 5 7 7 7 6 6 6 6 7 6 4 6
4 5 4 2 4 4 4 2 1 3
7 6 8 8 8 7 7 7 7 8 7 5 7
5 6 5 3 5 5 5 3 2 4
6 5 7 7 7 6 6 6 6 7 6 4 6
4 5 4 2 4 4 4 2 1 3
7 6 8 8 8 7 7 7 7 8 7 5 7
5 6 5 3 5 5 5 3 2 4
7 7 7 6
8 6 6
5 6 5 5 4 3
3 2 8 8 8 8
7
4 3 9 9 9 9 7 8
7 7 6 6 6 8
3 2 8 8 8 8
7
4 3 9 9 9 9 7 8
7 7 6 6 6 8
8 8 8 7 2
3 2 8 8 8 8 6 7
9 9 9 8 3
4 3 9 9 9 9 7 8
8 8 8 7 2
3 2 8 8 8 8 6 7
9 9 9 8 3
4 3 9 9 9 9 7 8
6 7
6 6 5 5 5
6 7
6 6 5 5 5
7 6 6 5 5 5
8 7 7 6 6 6
7 6 6 5 5 5
8 7 7 6 6 6
AlTiN
TiCN
FIRE
AlCrN
TiN
MolyGlide
83
Twist Drills
Carbide
Carbide
Ratio Drills
Tools with bold feed column no. are preferred choice.
Twist Drills
Drill mm 0.50 1.00 2.00 2.50 3.15 4.00 5.00 6.30 8.00 10.00 12.50 16.00 20.00 25.00 31.50 40.00 50.00 63.00 80.00
1
0.004 0.006 0.020 0.025 0.032 0.040 0.040 0.050 0.063 0.080 0.080 0.100 0.125 0.160 0.160 0.200 0.250 0.315 0.400
2
0.006 0.008 0.025 0.032 0.040 0.050 0.050 0.063 0.080 0.100 0.100 0.125 0.160 0.200 0.200 0.250 0.310 0.400 0.500
3
0.007 0.012 0.032 0.040 0.050 0.063 0.063 0.080 0.100 0.125 0.125 0.160 0.200 0.250 0.250 0.315 0.400 0.500 0.630
7
0.014 0.020 0.080 0.100 0.125 0.160 0.160 0.200 0.250 0.315 0.315 0.400 0.500 0.630 0.630 0.800 1.000 1.250 1.600
8
0.016 0.023 0.100 0.125 0.160 0.200 0.200 0.250 0.315 0.400 0.400 0.500 0.630 0.800 0.800 1.000 1.250 1.600 1.600
9
0.019 0.025 0.125 0.160 0.160 0.200 0.250 0.315 0.315 0.400 0.500 0.630 0.630 0.800 1.000 1.250 1.250 1.600 2.000
Cooling: without coolant ducts with coolant ducts Coolant: Air Neat oil Soluble oil Cutting direction: right-hand cutting left-hand cutting
Material group Common structural steels Free-cutting steels Unalloyed heat-treatable steels
Alloyed heat-treatable steels Unalloyed case hardened steels Alloyed case hardened steels Nitriding steels Tool steels High speed steels Spring steels Stainless steels, sulphured austenitic martensitic Hardened steels Special alloys Cast iron Spheroidal graphite iron and malleable cast iron Chilled cast iron Ti and Ti-alloys Aluminium and Al-alloys Al wrought alloys Al cast alloys 10 % Si > 10 % Si Magnesium alloys Copper, low-alloyed Brass, short-chipping long-chipping Bronze, short-chipping Bronze, long-chipping Duroplastics Thermoplastics Kevlar Glass, carbon concent. plastics
Material examples, new description (old description in brackets) Figures in bold = material no. to DIN EN 1.0035 S185(St33),1.0486 P275N(StE285),1.0345 P235GH(H1),1.0425 P265GH(H2) 1.0050 E295 (St50-2), 1.0070 E360 (St70-2), 1.8937 P500NH (WStE500) 1.0718 11SMnPb30 (9SMnPb28), 1.0736 11SMn37 (9SMn36) 1.0727 46S20 (45S20), 1.0728 (60S20), 1.0757 46SPb20 (45SPb20) 1.0402 C22, 1.1178 C30E (Ck30) 1.0503 C45, 1.1191 C45E (Ck45) 1.0601 C60, 1.1221 C60E (Ck60) 1.5131 50MnSi4, 1.7003 38Cr2, 1.7030 28Cr4 1.5710 36NiCr6, 1.7035 41Cr4, 1.7225 42CrMo4 1.0301 (C10), 1.1121 C10E (Ck10) 1.7043 38Cr4 1.5752 15NiCr13 (15NiCr13), 1.7131 16MnCr5, 1.7264 20CrMo5 1.8504 34CrAl6 1.8519 31CrMoV9, 1.8550 34CrAlNi7 1.1750 C75W, 1.2067 102Cr6, 1.2307 29CrMoV9 1.2080 X210Cr12, 1.2083 X42Cr13, 1.2419 105WCr6, 1.2767 X45NiCrMo4 1.3243 S 6-5-2-5, 1.3343 S 6-5-2, 1.3344 S 6-5-3 1.5026 55Si7, 1.7176 55Cr3, 1.8159 51CrV4 (51CrV4) 1.4005 X12CrS13, 1.4104 X14CrMoS17, 1.4105 X6CrMoS17, 1.4305 X8CrNiS18-9 1.4301 X5CrNi18-10 (V2A), 1.4541 X6CrNiTi18-10, 1.4571 X6CrNiMoTi 17-12-2 (V4A) 1.4057 X20CrNi 17 2 (X17CrNi16-2), 1.4122 X39CrMo17-1, 1.4521 X2CrMoTi18-2 Nimonic, Inconel, Monel, Hastelloy 0.6010 EN-GJL-100(GG10), 0.6020 EN-GJL-200(GG20) 0.6025 EN-GJL-250(GG25), 0.6035 EN-GJL-350(GG35) 0.7050 EN-GJS-500-7(GGG50), 0.8035 EN-GJMW-350-4(GTW35) 0.7070 EN-GJS-700-2(GGG70), 0.8170 EN-GJMB-700-2(GTS70) 3.7024 Ti99,5, 3.7114 TiAl5Sn2,5, 3.7124 TiCu2 3.7154 TiAl6Zr5, 3.7165 TiAl6V4, 3.7184 TiAl4Mo4Sn2,5, - TiAl8Mo1V1 3.0255 Al99,5, 3.2315 AlMgSi1, 3.3515 AlMg1 3.0615 AlMgSiPb, 3.1325 AlCuMg1, 3.3245 AlMg3Si, 3.4365 AlZnMgCu1,5 3.2131 G-AlSi5Cu1, 3.2153 G-AlSi7Cu3, 3.2573 G-AlSi9 3.2581 G-AlSi12, 3.2583 G-AlSi12Cu, - G-AlSi12CuNiMg 3.5200 MgMn2, 3.5812.05 G-MgAl8Zn1, 3.5612.05 G-MgAl6Zn1 2.0070 SE-Cu, 2.1020 CuSn6, 2.1096 G-CuSn5ZnPb 2.0380 CuZn39Pb2, 2.0401 CuZn39Pb3, 2.0410 CuZn43Pb2 2.0250 CuZn20, 2.0280 CuZn33, 2.0332 CuZn37Pb0,5 2.1090 CuSn7ZnPb, 2.1170 CuPb5Sn5, 2.1176 CuPb10Sn 2.0790 CuNi18Zn19Pb 2.0916 CuAl5, 2.0960 CuAl9Mn, 2.1050 CuSn10 2.0980 CuAl11Ni, 2.1247 CuBe2 Bakelit, Resopal, Pertinax, Moltopren Plexiglass, Hostalen, Novodur, Makralon Kevlar GFK/CFK
Tensile strength Hardness MPa (N/mm2) 500 >500-850 850 850-1000 700 700-850 850-1000 850-1000 1000-1200 750 850-1000 1000-1200 850-1000 >1000-1200 850 >850-1000 650-1000 330 HB 850 850 850 40-48 HRC >48-60 HRC 1200 240 HB <300 HB 240 HB <300 HB 350 HB 850 >850-1200 400 450 600 600 450 400 600 600 600 >600-850 850 >850-1000
Coolant
bright
steam tempered
nitrided lands
nitrided
golden brown
TiAlN
84
GUHRINGGUIDE
Tool material Carbide grade Type Surface finish Cooling HA DIN 6537 HE G.S. DZ Std. range, page
Carbide
K/P RT 100 F
K/P RT 100 U
Guh. no.
2717
499
499
499
499
vc vc m/min m/min 100 85 110 85 90 85 80 80 75 100 90 65 75 70 50 40 35 40 35 35 35 20 20 160 120 120 95 25 30 25 200 200 170 140 200 80 210 140 80 65 60 45 130 110 145 110 120 110 105 105 100 130 120 85 100 90 65 55 55 45 55 45 45 45 25 25 195 155 145 125 35 40 35 260 260 220 170 260 105 270 180 105 85 80 60 7 6 8 7 7 7 7 7 6 8 7 5 6
5 6 5 4 3 4 4 3 2 2 4
8 8 7 7 3
6 5 7 6 6 6 6 6 5 7 6 4 5
4 5 4 2 3 3 2 2 1 3
7 6 8 7 7 7 7 7 6 8 7 5 6
5 6 5
6 5 7 6 6 6 6 6 5 7 6 4 5
4 5 4 2 3 3 2 2 1 3
7 6 8 7 7 7 7 7 6 8 7 5 6
5 6 5 3 4 4 3 3 2 4
6 5 7 6 6 6 6 6 5 7 6 4 5
4 5 4 2 3 3 2 2 1 3
7 6 8 7 7 7 7 7 6 8 7 5 6
5 6 5 3 4 4 3 3 2 4
3 3 9 9 9 8 7 8
7 6 6 5 5 8
7 7 6 6 2
3 2 8 8 8 7 6 7
8 8 7 7 3
4 3 9 9 8 8 7 8
3 4 4 3 3 2 4
7 7 6 6 2
3 2 8 8 8 7 6 7
8 8 7 7 3
4 3 9 9 8 8 7 8
7 7 6 6 2
3 2 8 8 8 7 6 7
8 8 7 7 3
4 3 9 9 8 8 7 8
7 6 5 5 4 4
8 7 6 6 5 5
7 6 5 5 4 4
8 7 6 6 5 5
7 6 5 5 4 4
8 7 6 6 5 5
AlTiN
TiCN
FIRE
AlCrN
TiN
MolyGlide
85
Twist Drills
Ratio Drills
Tools with bold feed column no. are preferred choice.
Twist Drills
Drill mm 0.50 1.00 2.00 2.50 3.15 4.00 5.00 6.30 8.00 10.00 12.50 16.00 20.00 25.00 31.50 40.00 50.00 63.00 80.00
1
0.004 0.006 0.020 0.025 0.032 0.040 0.040 0.050 0.063 0.080 0.080 0.100 0.125 0.160 0.160 0.200 0.250 0.315 0.400
2
0.006 0.008 0.025 0.032 0.040 0.050 0.050 0.063 0.080 0.100 0.100 0.125 0.160 0.200 0.200 0.250 0.310 0.400 0.500
3
0.007 0.012 0.032 0.040 0.050 0.063 0.063 0.080 0.100 0.125 0.125 0.160 0.200 0.250 0.250 0.315 0.400 0.500 0.630
7
0.014 0.020 0.080 0.100 0.125 0.160 0.160 0.200 0.250 0.315 0.315 0.400 0.500 0.630 0.630 0.800 1.000 1.250 1.600
8
0.016 0.023 0.100 0.125 0.160 0.200 0.200 0.250 0.315 0.400 0.400 0.500 0.630 0.800 0.800 1.000 1.250 1.600 1.600
9
0.019 0.025 0.125 0.160 0.160 0.200 0.250 0.315 0.315 0.400 0.500 0.630 0.630 0.800 1.000 1.250 1.250 1.600 2.000
Cooling: without coolant ducts with coolant ducts Coolant: Air Neat oil Soluble oil Cutting direction: right-hand cutting left-hand cutting Al especially suitable for machining aluminium G especially suitable for machining cast iron
Material group Common structural steels Free-cutting steels Unalloyed heat-treatable steels
Alloyed heat-treatable steels Unalloyed case hardened steels Alloyed case hardened steels Nitriding steels Tool steels High speed steels Spring steels Stainless steels, sulphured austenitic martensitic Hardened steels Special alloys Cast iron Spheroidal graphite iron and malleable cast iron Chilled cast iron Ti and Ti-alloys Aluminium and Al-alloys Al wrought alloys Al cast alloys 10 % Si > 10 % Si Magnesium alloys Copper, low-alloyed Brass, short-chipping long-chipping Bronze, short-chipping Bronze, long-chipping Duroplastics Thermoplastics Kevlar Glass, carbon concent. plastics
Material examples, new description (old description in brackets) Figures in bold = material no. to DIN EN 1.0035 S185(St33),1.0486 P275N(StE285),1.0345 P235GH(H1),1.0425 P265GH(H2) 1.0050 E295 (St50-2), 1.0070 E360 (St70-2), 1.8937 P500NH (WStE500) 1.0718 11SMnPb30 (9SMnPb28), 1.0736 11SMn37 (9SMn36) 1.0727 46S20 (45S20), 1.0728 (60S20), 1.0757 46SPb20 (45SPb20) 1.0402 C22, 1.1178 C30E (Ck30) 1.0503 C45, 1.1191 C45E (Ck45) 1.0601 C60, 1.1221 C60E (Ck60) 1.5131 50MnSi4, 1.7003 38Cr2, 1.7030 28Cr4 1.5710 36NiCr6, 1.7035 41Cr4, 1.7225 42CrMo4 1.0301 (C10), 1.1121 C10E (Ck10) 1.7043 38Cr4 1.5752 15NiCr13 (15NiCr13), 1.7131 16MnCr5, 1.7264 20CrMo5 1.8504 34CrAl6 1.8519 31CrMoV9, 1.8550 34CrAlNi7 1.1750 C75W, 1.2067 102Cr6, 1.2307 29CrMoV9 1.2080 X210Cr12, 1.2083 X42Cr13, 1.2419 105WCr6, 1.2767 X45NiCrMo4 1.3243 S 6-5-2-5, 1.3343 S 6-5-2, 1.3344 S 6-5-3 1.5026 55Si7, 1.7176 55Cr3, 1.8159 51CrV4 (51CrV4) 1.4005 X12CrS13, 1.4104 X14CrMoS17, 1.4105 X6CrMoS17, 1.4305 X8CrNiS18-9 1.4301 X5CrNi18-10 (V2A), 1.4541 X6CrNiTi18-10, 1.4571 X6CrNiMoTi 17-12-2 (V4A) 1.4057 X20CrNi 17 2 (X17CrNi16-2), 1.4122 X39CrMo17-1, 1.4521 X2CrMoTi18-2 Nimonic, Inconel, Monel, Hastelloy 0.6010 EN-GJL-100(GG10), 0.6020 EN-GJL-200(GG20) 0.6025 EN-GJL-250(GG25), 0.6035 EN-GJL-350(GG35) 0.7050 EN-GJS-500-7(GGG50), 0.8035 EN-GJMW-350-4(GTW35) 0.7070 EN-GJS-700-2(GGG70), 0.8170 EN-GJMB-700-2(GTS70) 3.7024 Ti99,5, 3.7114 TiAl5Sn2,5, 3.7124 TiCu2 3.7154 TiAl6Zr5, 3.7165 TiAl6V4, 3.7184 TiAl4Mo4Sn2,5, - TiAl8Mo1V1 3.0255 Al99,5, 3.2315 AlMgSi1, 3.3515 AlMg1 3.0615 AlMgSiPb, 3.1325 AlCuMg1, 3.3245 AlMg3Si, 3.4365 AlZnMgCu1,5 3.2131 G-AlSi5Cu1, 3.2153 G-AlSi7Cu3, 3.2573 G-AlSi9 3.2581 G-AlSi12, 3.2583 G-AlSi12Cu, - G-AlSi12CuNiMg 3.5200 MgMn2, 3.5812.05 G-MgAl8Zn1, 3.5612.05 G-MgAl6Zn1 2.0070 SE-Cu, 2.1020 CuSn6, 2.1096 G-CuSn5ZnPb 2.0380 CuZn39Pb2, 2.0401 CuZn39Pb3, 2.0410 CuZn43Pb2 2.0250 CuZn20, 2.0280 CuZn33, 2.0332 CuZn37Pb0,5 2.1090 CuSn7ZnPb, 2.1170 CuPb5Sn5, 2.1176 CuPb10Sn 2.0790 CuNi18Zn19Pb 2.0916 CuAl5, 2.0960 CuAl9Mn, 2.1050 CuSn10 2.0980 CuAl11Ni, 2.1247 CuBe2 Bakelit, Resopal, Pertinax, Moltopren Plexiglass, Hostalen, Novodur, Makralon Kevlar GFK/CFK
Tensile strength Hardness MPa (N/mm2) 500 >500-850 850 850-1000 700 700-850 850-1000 850-1000 1000-1200 750 850-1000 1000-1200 850-1000 >1000-1200 850 >850-1000 650-1000 330 HB 850 850 850 40-48 HRC >48-60 HRC 1200 240 HB <300 HB 240 HB <300 HB 350 HB 850 >850-1200 400 450 600 600 450 400 600 600 600 >600-850 850 >850-1000
Coolant
bright
steam tempered
nitrided lands
nitrided
golden brown
TiAlN
86
GUHRINGGUIDE
Tool material Carb.-tipped Carbide grade P Type RT 80 U Surface finish Cooling DIN 6538 HE 1173 HA G.S. HE Std. range, page 548
Carbide
Carbide
K/P RT 100 U
Carbide
Carbide
K RT 150 GG
K RT 150 GG
K RT 150 GN
Guh. no.
769 538 Al
6069
2711 530
770
540
6070
540
773 542 Al
538
G
Al
vc m/min 95 75 90 75 80 75 60 75 60 90 75 55 75 55 40 35 40 35 33 25
vc m/min
vc vc m/min m/min 110 90 130 110 100 95 90 90 80 110 90 65 80 75 55 40 45 45 45 40 35 40 25 25 150 120 100 95 30 35 30 220 220 200 170 230 95 250 170 95 80 70 60 145 120 170 145 130 125 120 120 105 145 120 85 110 105 80 65 60 60 60 55 45 55 35 35 210 180 160 130 40 40 40 310 310 260 220 280 125 325 220 125 105 90 80
vc m/min
vc m/min
5 4 6 6 6 5 5 5 5 6 5 3 5 4
4 3 2 1 3 3 3 1 1 2
6 5 7 7 7 6 6 6 6 7 6
4 6 4 5 4 4 2 4 4 4 2 1 3
5 5 5 4
120 100 90 80 40
6 6 6 6 2
7 7 7 7 2
7 7 7 6 1 7 7 7 7 6 6 6 5 5 5
6 7 1 1
8 8 8 7
2 3 2
120 100 90 80 40
6 6 6 6 2
6 6 6 6 1
120 100 90 80 40
5 5 5 5 1
6 6 6 5
8 8
7 6 5
8 8
7 7 7 7
8 8 8 8 7
6 7 6
8 8
7 6 5
8 8
6 6 6 6
7 7
6 5 4
6 6
280 110 80
7 6 5
280 110 80
7 6 5
280 110 80
6 5 5 5
AlTiN
TiCN
FIRE
AlCrN
TiN
MolyGlide
87
Twist Drills
10D 15D
Ratio Drills
Tools with bold feed column no. are preferred choice.
Twist Drills
Drill mm 0.50 1.00 2.00 2.50 3.15 4.00 5.00 6.30 8.00 10.00 12.50 16.00 20.00 25.00 31.50 40.00 50.00 63.00 80.00
1
0.004 0.006 0.020 0.025 0.032 0.040 0.040 0.050 0.063 0.080 0.080 0.100 0.125 0.160 0.160 0.200 0.250 0.315 0.400
2
0.006 0.008 0.025 0.032 0.040 0.050 0.050 0.063 0.080 0.100 0.100 0.125 0.160 0.200 0.200 0.250 0.310 0.400 0.500
3
0.007 0.012 0.032 0.040 0.050 0.063 0.063 0.080 0.100 0.125 0.125 0.160 0.200 0.250 0.250 0.315 0.400 0.500 0.630
7
0.014 0.020 0.080 0.100 0.125 0.160 0.160 0.200 0.250 0.315 0.315 0.400 0.500 0.630 0.630 0.800 1.000 1.250 1.600
8
0.016 0.023 0.100 0.125 0.160 0.200 0.200 0.250 0.315 0.400 0.400 0.500 0.630 0.800 0.800 1.000 1.250 1.600 1.600
9
0.019 0.025 0.125 0.160 0.160 0.200 0.250 0.315 0.315 0.400 0.500 0.630 0.630 0.800 1.000 1.250 1.250 1.600 2.000
Cooling: without coolant ducts with coolant ducts Coolant: Air Neat oil Soluble oil Cutting direction: right-hand cutting left-hand cutting
Material group Common structural steels Free-cutting steels Unalloyed heat-treatable steels
Alloyed heat-treatable steels Unalloyed case hardened steels Alloyed case hardened steels Nitriding steels Tool steels High speed steels Spring steels Stainless steels, sulphured austenitic martensitic Hardened steels Special alloys Cast iron Spheroidal graphite iron and malleable cast iron Chilled cast iron Ti and Ti-alloys Aluminium and Al-alloys Al wrought alloys Al cast alloys 10 % Si > 10 % Si Magnesium alloys Copper, low-alloyed Brass, short-chipping long-chipping Bronze, short-chipping Bronze, long-chipping Duroplastics Thermoplastics Kevlar Glass, carbon concent. plastics
Material examples, new description (old description in brackets) Figures in bold = material no. to DIN EN 1.0035 S185(St33),1.0486 P275N(StE285),1.0345 P235GH(H1),1.0425 P265GH(H2) 1.0050 E295 (St50-2), 1.0070 E360 (St70-2), 1.8937 P500NH (WStE500) 1.0718 11SMnPb30 (9SMnPb28), 1.0736 11SMn37 (9SMn36) 1.0727 46S20 (45S20), 1.0728 (60S20), 1.0757 46SPb20 (45SPb20) 1.0402 C22, 1.1178 C30E (Ck30) 1.0503 C45, 1.1191 C45E (Ck45) 1.0601 C60, 1.1221 C60E (Ck60) 1.5131 50MnSi4, 1.7003 38Cr2, 1.7030 28Cr4 1.5710 36NiCr6, 1.7035 41Cr4, 1.7225 42CrMo4 1.0301 (C10), 1.1121 C10E (Ck10) 1.7043 38Cr4 1.5752 15NiCr13 (15NiCr13), 1.7131 16MnCr5, 1.7264 20CrMo5 1.8504 34CrAl6 1.8519 31CrMoV9, 1.8550 34CrAlNi7 1.1750 C75W, 1.2067 102Cr6, 1.2307 29CrMoV9 1.2080 X210Cr12, 1.2083 X42Cr13, 1.2419 105WCr6, 1.2767 X45NiCrMo4 1.3243 S 6-5-2-5, 1.3343 S 6-5-2, 1.3344 S 6-5-3 1.5026 55Si7, 1.7176 55Cr3, 1.8159 51CrV4 (51CrV4) 1.4005 X12CrS13, 1.4104 X14CrMoS17, 1.4105 X6CrMoS17, 1.4305 X8CrNiS18-9 1.4301 X5CrNi18-10 (V2A), 1.4541 X6CrNiTi18-10, 1.4571 X6CrNiMoTi 17-12-2 (V4A) 1.4057 X20CrNi 17 2 (X17CrNi16-2), 1.4122 X39CrMo17-1, 1.4521 X2CrMoTi18-2 Nimonic, Inconel, Monel, Hastelloy 0.6010 EN-GJL-100(GG10), 0.6020 EN-GJL-200(GG20) 0.6025 EN-GJL-250(GG25), 0.6035 EN-GJL-350(GG35) 0.7050 EN-GJS-500-7(GGG50), 0.8035 EN-GJMW-350-4(GTW35) 0.7070 EN-GJS-700-2(GGG70), 0.8170 EN-GJMB-700-2(GTS70) 3.7024 Ti99,5, 3.7114 TiAl5Sn2,5, 3.7124 TiCu2 3.7154 TiAl6Zr5, 3.7165 TiAl6V4, 3.7184 TiAl4Mo4Sn2,5, - TiAl8Mo1V1 3.0255 Al99,5, 3.2315 AlMgSi1, 3.3515 AlMg1 3.0615 AlMgSiPb, 3.1325 AlCuMg1, 3.3245 AlMg3Si, 3.4365 AlZnMgCu1,5 3.2131 G-AlSi5Cu1, 3.2153 G-AlSi7Cu3, 3.2573 G-AlSi9 3.2581 G-AlSi12, 3.2583 G-AlSi12Cu, - G-AlSi12CuNiMg 3.5200 MgMn2, 3.5812.05 G-MgAl8Zn1, 3.5612.05 G-MgAl6Zn1 2.0070 SE-Cu, 2.1020 CuSn6, 2.1096 G-CuSn5ZnPb 2.0380 CuZn39Pb2, 2.0401 CuZn39Pb3, 2.0410 CuZn43Pb2 2.0250 CuZn20, 2.0280 CuZn33, 2.0332 CuZn37Pb0,5 2.1090 CuSn7ZnPb, 2.1170 CuPb5Sn5, 2.1176 CuPb10Sn 2.0790 CuNi18Zn19Pb 2.0916 CuAl5, 2.0960 CuAl9Mn, 2.1050 CuSn10 2.0980 CuAl11Ni, 2.1247 CuBe2 Bakelit, Resopal, Pertinax, Moltopren Plexiglass, Hostalen, Novodur, Makralon Kevlar GFK/CFK
Tensile strength Hardness MPa (N/mm2) 500 >500-850 850 850-1000 700 700-850 850-1000 850-1000 1000-1200 750 850-1000 1000-1200 850-1000 >1000-1200 850 >850-1000 650-1000 330 HB 850 850 850 40-48 HRC >48-60 HRC 1200 240 HB <300 HB 240 HB <300 HB 350 HB 850 >850-1200 400 450 600 600 450 400 600 600 600 >600-850 850 >850-1000
Coolant
bright
steam tempered
nitrided lands
nitrided
golden brown
TiAlN
88
GUHRINGGUIDE
Tool material Carbide grade Type Surface finish Cooling DIN 6537 HA DZ DIN 6539 DZ Std. range, page
Carbide
Carbide
K FT 200 G K/P FT 200 G L GS 200 U K/P GS 200 U
K GS 200 G
K GS 200 G
K GS 200 G
K/P GS 200 F
Guh. no.
vc m/min
100 80 80 70
6 6 6 6
100 80 80 70
6 6 6 6
6 6 6 6
6 6 6 6
6 6 6 6
7 7 7 7
6 6 6 6
6 6 6 6
7 7 7 6 6 6
7 6 6 6
7 7 7 6 6 6
7 7 7 6 6 6
7 7 7 6 6 6
8 8 8 7 7 4 7
7 7 7 6 6 6
7 7 7 6 6 6
AlTiN
TiCN
FIRE
AlCrN
TiN
MolyGlide
89
Twist Drills
3D
5D 3-fluted
Twist Drills
Drills mm 0.80 1.00 1.50 2.00 2.50 3.00 Material group Common structural steels Free-cutting steels Unalloyed heat-treatable steels
60
0.04 0.06 0.09 0.12 0.15 0.18
68
0.09 0.12 0.18 0.24 0.30 0.36 Coolant
Alloyed heat-treatable steels Unalloyed case hardened steels Alloyed case hardened steels Nitriding steels Tool steels High speed steels Spring steels Stainless steels, sulphured austenitic martensitic Hardened steels Special alloys Cast iron Spheroidal graphite iron and malleable cast iron Chilled cast iron Ti and Ti-alloys Aluminium and Al-alloys Al wrought alloys Al cast alloys 10 % Si > 10 % Si Magnesium alloys Copper, low-alloyed Brass, short-chipping long-chipping Bronze, short-chipping Bronze, long-chipping Duroplastics Thermoplastics Kevlar Glass, carbon concent. plastics
Material examples, new description (old description in brackets) Figures in bold = material no. to DIN EN 1.0035 S185(St33),1.0486 P275N(StE285),1.0345 P235GH(H1),1.0425 P265GH(H2) 1.0050 E295 (St50-2), 1.0070 E360 (St70-2), 1.8937 P500NH (WStE500) 1.0718 11SMnPb30 (9SMnPb28), 1.0736 11SMn37 (9SMn36) 1.0727 46S20 (45S20), 1.0728 (60S20), 1.0757 46SPb20 (45SPb20) 1.0402 C22, 1.1178 C30E (Ck30) 1.0503 C45, 1.1191 C45E (Ck45) 1.0601 C60, 1.1221 C60E (Ck60) 1.5131 50MnSi4, 1.7003 38Cr2, 1.7030 28Cr4 1.5710 36NiCr6, 1.7035 41Cr4, 1.7225 42CrMo4 1.0301 (C10), 1.1121 C10E (Ck10) 1.7043 38Cr4 1.5752 15NiCr13 (15NiCr13), 1.7131 16MnCr5, 1.7264 20CrMo5 1.8504 34CrAl6 1.8519 31CrMoV9, 1.8550 34CrAlNi7 1.1750 C75W, 1.2067 102Cr6, 1.2307 29CrMoV9 1.2080 X210Cr12, 1.2083 X42Cr13, 1.2419 105WCr6, 1.2767 X45NiCrMo4 1.3243 S 6-5-2-5, 1.3343 S 6-5-2, 1.3344 S 6-5-3 1.5026 55Si7, 1.7176 55Cr3, 1.8159 51CrV4 (51CrV4) 1.4005 X12CrS13, 1.4104 X14CrMoS17, 1.4105 X6CrMoS17, 1.4305 X8CrNiS18-9 1.4301 X5CrNi18-10 (V2A), 1.4541 X6CrNiTi18-10, 1.4571 X6CrNiMoTi 17-12-2 (V4A) 1.4057 X20CrNi 17 2 (X17CrNi16-2), 1.4122 X39CrMo17-1, 1.4521 X2CrMoTi18-2 Nimonic, Inconel, Monel, Hastelloy 0.6010 EN-GJL-100(GG10), 0.6020 EN-GJL-200(GG20) 0.6025 EN-GJL-250(GG25), 0.6035 EN-GJL-350(GG35) 0.7050 EN-GJS-500-7(GGG50), 0.8035 EN-GJMW-350-4(GTW35) 0.7070 EN-GJS-700-2(GGG70), 0.8170 EN-GJMB-700-2(GTS70) 3.7024 Ti99,5, 3.7114 TiAl5Sn2,5, 3.7124 TiCu2 3.7154 TiAl6Zr5, 3.7165 TiAl6V4, 3.7184 TiAl4Mo4Sn2,5, - TiAl8Mo1V1 3.0255 Al99,5, 3.2315 AlMgSi1, 3.3515 AlMg1 3.0615 AlMgSiPb, 3.1325 AlCuMg1, 3.3245 AlMg3Si, 3.4365 AlZnMgCu1,5 3.2131 G-AlSi5Cu1, 3.2153 G-AlSi7Cu3, 3.2573 G-AlSi9 3.2581 G-AlSi12, 3.2583 G-AlSi12Cu, - G-AlSi12CuNiMg 3.5200 MgMn2, 3.5812.05 G-MgAl8Zn1, 3.5612.05 G-MgAl6Zn1 2.0070 SE-Cu, 2.1020 CuSn6, 2.1096 G-CuSn5ZnPb 2.0380 CuZn39Pb2, 2.0401 CuZn39Pb3, 2.0410 CuZn43Pb2 2.0250 CuZn20, 2.0280 CuZn33, 2.0332 CuZn37Pb0,5 2.1090 CuSn7ZnPb, 2.1170 CuPb5Sn5, 2.1176 CuPb10Sn 2.0790 CuNi18Zn19Pb 2.0916 CuAl5, 2.0960 CuAl9Mn, 2.1050 CuSn10 2.0980 CuAl11Ni, 2.1247 CuBe2 Bakelit, Resopal, Pertinax, Moltopren Plexiglass, Hostalen, Novodur, Makralon Kevlar GFK/CFK
Tensile strength Hardness MPa (N/mm2) 500 >500-850 850 850-1000 700 700-850 850-1000 850-1000 1000-1200 750 850-1000 1000-1200 850-1000 >1000-1200 850 >850-1000 650-1000 330 HB 850 850 850 40-48 HRC >48-60 HRC 1200 240 HB <300 HB 240 HB <300 HB 350 HB 850 >850-1200 400 450 600 600 450 400 600 600 600 >600-850 850 >850-1000
bright
steam tempered
nitrided lands
nitrided
golden brown
TiAlN
90
GUHRINGGUIDE
Tool material Carbide grade Type Surface finish Cooling G.S. G.S. Std. range, page
Carbide
K/P N
K/P N
Guh. no.
Tool material Carbide grade Type Surface finish Cooling DIN 6537 HA G.S. HA Std. range, page
Carbide
K/P RT 100 R
K/P RT 100 R
G No.
530
Drills mm 0.50 1.00 2.00 2.50 3.15 4.00 5.00 6.30 8.00 10.00 12.50 16.00 20.00 25.00 31.50 40.00 50.00 63.00 80.00 vc m/min 90-120 90-110 90-120 80-100 80-110 80-110 80-100 80-100 60-80 90-110 70-100 60-80 60-80 50-70 40-60 40-60 Feed column no. 64 64 64 63 64 64 63 63 62 63 63 62 62 62 62 62 62 62 62 61 62 62 61 61 60 61 61 60 60 60 60 60
1
0.004 0.006 0.020 0.025 0.032 0.040 0.040 0.050 0.063 0.080 0.080 0.100 0.125 0.160 0.160 0.200 0.250 0.315 0.400
2
0.006 0.008 0.025 0.032 0.040 0.050 0.050 0.063 0.080 0.100 0.100 0.125 0.160 0.200 0.200 0.250 0.310 0.400 0.500
8
0.016 0.023 0.100 0.125 0.160 0.200 0.200 0.250 0.315 0.400 0.400 0.500 0.630 0.800 0.800 1.000 1.250 1.600 1.600 Hardness 240 HB 300 HB 240 HB <300 HB
9
0.019 0.025 0.125 0.160 0.160 0.200 0.250 0.315 0.315 0.400 0.500 0.630 0.630 0.800 1.000 1.250 1.250 1.600 2.000 vc m/min 210 160 160 130 Feed column no.
Material examples Figures in bold = material no. to DIN EN Cast iron 0.6010 EN-GJL-100, 0.6020 EN-GJL-200 0.6025 EN-GJL-250, 0.6035 EN-GJL-350 Spher. graphite iron and 0.7050 EN-GJS-500-7, 0.8035 EN-GJMW-350-4 malleable cast iron 0.7070 EN-GJS-700-2, 0.8170 EN-GJMB-700-2 New cast materials
Cast iron with compacted graphite iron (CGI) Formable cast iron (step hardened) (ADI*) EN-GJV250, EN-GJV350 EN-GJV400, EN-GJV500 EN-GJS-800-8, EN-GJS-1000-5 EN-GJS-1200-2, EN-GJS-1000-1
Material group
9 9 9 8
8 8 8 7
130 100 80 60
8 8 8 8
7 7 7 7
General recommendations: Powerful machines, no play in spindle bearings, alignment accurate tool holders. Max. concentricity error of clamped tools 0.02 mm, high coolant pressures. We recommend the application of hydraulic chucks or shrink fit chucks. External cooling recommendations: We recommend using soluble oil or neat oil. With RT 100 R, cooling with air is also possible under certain conditions. However, the application under MQL conditions, for which the tools are extremely well suited, is always preferable. For MQL applications we recommend the tapered MQL shank end as well as the MQL components from Guhring. Further information is available on request.
68 68 68 67
66 66 66 65
AlTiN
TiCN
FIRE
AlCrN
TiN
MolyGlide
91
Twist Drills
5D 7D
Twist Drills
for through holes supporting lands must remain in permanent contact. for 7 x D, centering is recommended with equal point angle of 140, or larger, to min. 2/3 cutting edge diameter. interrupted cutting (grooves, transverse holes) is not recommended without prior tests. For interrupted cutting (max. 0.2xD) it is recommended to reduce the feed rate whenever possible. in contrast to conventional indexable inserts, HT 800 is also suitable for the drilling of stacked sheets.
Drill mm 0.50 1.00 2.00 2.50 3.15 4.00 5.00 6.30 8.00 10.00 12.50 16.00 20.00 25.00 31.50 40.00 50.00 63.00 80.00
1
0.004 0.006 0.020 0.025 0.032 0.040 0.040 0.050 0.063 0.080 0.080 0.100 0.125 0.160 0.160 0.200 0.250 0.315 0.400
2
0.006 0.008 0.025 0.032 0.040 0.050 0.050 0.063 0.080 0.100 0.100 0.125 0.160 0.200 0.200 0.250 0.310 0.400 0.500
3
0.007 0.012 0.032 0.040 0.050 0.063 0.063 0.080 0.100 0.125 0.125 0.160 0.200 0.250 0.250 0.315 0.400 0.500 0.630
7
0.014 0.020 0.080 0.100 0.125 0.160 0.160 0.200 0.250 0.315 0.315 0.400 0.500 0.630 0.630 0.800 1.000 1.250 1.600
8
0.016 0.023 0.100 0.125 0.160 0.200 0.200 0.250 0.315 0.400 0.400 0.500 0.630 0.800 0.800 1.000 1.250 1.600 1.600
9
0.019 0.025 0.125 0.160 0.160 0.200 0.250 0.315 0.315 0.400 0.500 0.630 0.630 0.800 1.000 1.250 1.250 1.600 2.000
Cooling: without coolant ducts with coolant ducts Coolant: Air Neat oil Soluble oil Cutting direction: right-hand cutting left-hand cutting
Material group Common structural steels Free-cutting steels Unalloyed heat-treatable steels
Alloyed heat-treatable steels Unalloyed case hardened steels Alloyed case hardened steels Nitriding steels Tool steels High speed steels Spring steels Stainless steels, sulphured austenitic martensitic Hardened steels Special alloys Cast iron Spheroidal graphite iron and malleable cast iron Chilled cast iron Ti and Ti-alloys Aluminium and Al-alloys Al wrought alloys Al cast alloys 10 % Si > 10 % Si Magnesium alloys Copper, low-alloyed Brass, short-chipping long-chipping Bronze, short-chipping Bronze, long-chipping Duroplastics Thermoplastics Kevlar Glass, carbon concent. plastics
Material examples, new description (old description in brackets) Figures in bold = material no. to DIN EN 1.0035 S185(St33),1.0486 P275N(StE285),1.0345 P235GH(H1),1.0425 P265GH(H2) 1.0050 E295 (St50-2), 1.0070 E360 (St70-2), 1.8937 P500NH (WStE500) 1.0718 11SMnPb30 (9SMnPb28), 1.0736 11SMn37 (9SMn36) 1.0727 46S20 (45S20), 1.0728 (60S20), 1.0757 46SPb20 (45SPb20) 1.0402 C22, 1.1178 C30E (Ck30) 1.0503 C45, 1.1191 C45E (Ck45) 1.0601 C60, 1.1221 C60E (Ck60) 1.5131 50MnSi4, 1.7003 38Cr2, 1.7030 28Cr4 1.5710 36NiCr6, 1.7035 41Cr4, 1.7225 42CrMo4 1.0301 (C10), 1.1121 C10E (Ck10) 1.7043 38Cr4 1.5752 15NiCr13 (15NiCr13), 1.7131 16MnCr5, 1.7264 20CrMo5 1.8504 34CrAl6 1.8519 31CrMoV9, 1.8550 34CrAlNi7 1.1750 C75W, 1.2067 102Cr6, 1.2307 29CrMoV9 1.2080 X210Cr12, 1.2083 X42Cr13, 1.2419 105WCr6, 1.2767 X45NiCrMo4 1.3243 S 6-5-2-5, 1.3343 S 6-5-2, 1.3344 S 6-5-3 1.5026 55Si7, 1.7176 55Cr3, 1.8159 51CrV4 (51CrV4) 1.4005 X12CrS13, 1.4104 X14CrMoS17, 1.4105 X6CrMoS17, 1.4305 X8CrNiS18-9 1.4301 X5CrNi18-10 (V2A), 1.4541 X6CrNiTi18-10, 1.4571 X6CrNiMoTi 17-12-2 (V4A) 1.4057 X20CrNi 17 2 (X17CrNi16-2), 1.4122 X39CrMo17-1, 1.4521 X2CrMoTi18-2 Nimonic, Inconel, Monel, Hastelloy 0.6010 EN-GJL-100(GG10), 0.6020 EN-GJL-200(GG20) 0.6025 EN-GJL-250(GG25), 0.6035 EN-GJL-350(GG35) 0.7050 EN-GJS-500-7(GGG50), 0.8035 EN-GJMW-350-4(GTW35) 0.7070 EN-GJS-700-2(GGG70), 0.8170 EN-GJMB-700-2(GTS70) 3.7024 Ti99,5, 3.7114 TiAl5Sn2,5, 3.7124 TiCu2 3.7154 TiAl6Zr5, 3.7165 TiAl6V4, 3.7184 TiAl4Mo4Sn2,5, - TiAl8Mo1V1 3.0255 Al99,5, 3.2315 AlMgSi1, 3.3515 AlMg1 3.0615 AlMgSiPb, 3.1325 AlCuMg1, 3.3245 AlMg3Si, 3.4365 AlZnMgCu1,5 3.2131 G-AlSi5Cu1, 3.2153 G-AlSi7Cu3, 3.2573 G-AlSi9 3.2581 G-AlSi12, 3.2583 G-AlSi12Cu, - G-AlSi12CuNiMg 3.5200 MgMn2, 3.5812.05 G-MgAl8Zn1, 3.5612.05 G-MgAl6Zn1 2.0070 SE-Cu, 2.1020 CuSn6, 2.1096 G-CuSn5ZnPb 2.0380 CuZn39Pb2, 2.0401 CuZn39Pb3, 2.0410 CuZn43Pb2 2.0250 CuZn20, 2.0280 CuZn33, 2.0332 CuZn37Pb0,5 2.1090 CuSn7ZnPb, 2.1170 CuPb5Sn5, 2.1176 CuPb10Sn 2.0790 CuNi18Zn19Pb 2.0916 CuAl5, 2.0960 CuAl9Mn, 2.1050 CuSn10 2.0980 CuAl11Ni, 2.1247 CuBe2 Bakelit, Resopal, Pertinax, Moltopren Plexiglass, Hostalen, Novodur, Makralon Kevlar GFK/CFK
Tensile strength Hardness MPa (N/mm2) 500 >500-850 850 850-1000 700 700-850 850-1000 850-1000 1000-1200 750 850-1000 1000-1200 850-1000 >1000-1200 850 >850-1000 650-1000 330 HB 850 850 850 40-48 HRC >48-60 HRC 1200 240 HB <300 HB 240 HB <300 HB 350 HB 850 >850-1200 400 450 600 600 450 400 600 600 600 >600-850 850 >850-1000
Coolant
bright
steam tempered
nitrided lands
nitrided
golden brown
TiAlN
92
GUHRINGGUIDE
HT 800 WP
Twist Drills
Indexable inserts
Tool material Carbide grade Surface finish Guh. no. Std. range, page
Carbide
K 4024 566 K/P 4025 566 K/P 4026 566
general steels
Tool holders
Cooling Guh. no. Std. range page
3xD
4042 564
5xD
4043 564
7xD
4048 564
vc m/min 100 85 100 85 100 95 85 85 70 100 85 55 80 55 40 35 40 35 40 30 25 20 20 160 120 120 100 25 30 25 220 200 180 150 200 80 210 140 80 65 50 40 80 80 80 80 130 110 130 110 130 125 110 110 90 130 110 70 105 70 55 50 55 50 55 40 35 25 25 210 155 155 130 35 40 35 290 260 235 195 260 105 270 180 105 85 65 55 105 105 105 105
vc m/min 95 80 95 80 95 90 80 80 65 95 80 55 80 55 40 35 40 35 40 30 25 20 20 150 110 110 90 25 30 25 200 200 170 140 200 80 210 140 80 65 50 40 80 80 80 80 125 105 125 105 125 120 105 105 85 125 105 70 105 70 55 50 55 50 55 40 35 25 25 195 145 145 120 35 40 35 260 260 220 180 260 105 270 180 105 85 65 55 105 105 105 105
vc m/min 90 80 90 80 90 85 75 75 65 90 75 55 80 55 40 35 40 35 40 30 25 20 20 150 110 110 90 25 30 25 200 200 170 140 200 80 210 140 80 65 50 40 80 80 80 80 120 105 120 105 120 110 100 100 85 120 100 70 105 70 55 50 55 50 55 40 35 25 25 195 145 145 120 35 40 35 260 260 220 180 260 105 270 180 105 85 65 55 105 105 105 105
6 5 7 6 6 6 5 6 5 7 6 4
5 4 5 4 3 2 3 3 3 2 2
6 5 7 6 6 6 5 6 5 7 6 4
5 4 5 4 3 2 3 3 3 2 2
5 4 6 5 5 5 4 5 4 6 5 4
4 3 4 3 2 2 2 2 2 1 1
100 80 80 70 10
7 7 7 6
2 3 2 7 7 7 7 6 7 6 6 6 6 5 5 5 5 5
90 70 70 60 10
7 7 7 6
2 3 2 7 7 7 7 6 7 6 6 6 6 5 5 5 5 5
90 70 70 60 10
6 6 6 5
2 2 1 6 6 6 6 5 6 5 5 5 5 4 4 4 4 4
AlTiN
TiCN
FIRE
AlCrN
TiN
MolyGlide
93
Twist Drills
for through holes supporting lands must remain in permanent contact. for 7 x D, centering is recommended with equal point angle of 140, or larger, to min. 2/3 cutting edge diameter. interrupted cutting (grooves, transverse holes) is not recommended without prior tests. For interrupted cutting (max. 0.2xD) it is recommended to reduce the feed rate whenever possible. in contrast to conventional indexable inserts, RT 800 is also suitable for the drilling of stacked sheets. when replacing the inserts, it is recommended to also replace the original clamping screw with the included polyamide coated screw.
Drill mm 0.50 1.00 2.00 2.50 3.15 4.00 5.00 6.30 8.00 10.00 12.50 16.00 20.00 25.00 31.50 40.00 50.00 63.00 80.00
1
0.004 0.006 0.020 0.025 0.032 0.040 0.040 0.050 0.063 0.080 0.080 0.100 0.125 0.160 0.160 0.200 0.250 0.315 0.400
2
0.006 0.008 0.025 0.032 0.040 0.050 0.050 0.063 0.080 0.100 0.100 0.125 0.160 0.200 0.200 0.250 0.310 0.400 0.500
3
0.007 0.012 0.032 0.040 0.050 0.063 0.063 0.080 0.100 0.125 0.125 0.160 0.200 0.250 0.250 0.315 0.400 0.500 0.630
7
0.014 0.020 0.080 0.100 0.125 0.160 0.160 0.200 0.250 0.315 0.315 0.400 0.500 0.630 0.630 0.800 1.000 1.250 1.600
8
0.016 0.023 0.100 0.125 0.160 0.200 0.200 0.250 0.315 0.400 0.400 0.500 0.630 0.800 0.800 1.000 1.250 1.600 1.600
9
0.019 0.025 0.125 0.160 0.160 0.200 0.250 0.315 0.315 0.400 0.500 0.630 0.630 0.800 1.000 1.250 1.250 1.600 2.000
Cooling: without coolant ducts with coolant ducts Coolant: Air Neat oil Soluble oil Cutting direction: right-hand cutting left-hand cutting
Material group Common structural steels Free-cutting steels Unalloyed heat-treatable steels
Alloyed heat-treatable steels Unalloyed case hardened steels Alloyed case hardened steels Nitriding steels Tool steels High speed steels Spring steels Stainless steels, sulphured austenitic martensitic Hardened steels Special alloys Cast iron Spheroidal graphite iron and malleable cast iron Chilled cast iron Ti and Ti-alloys Aluminium and Al-alloys Al wrought alloys Al cast alloys 10 % Si > 10 % Si Magnesium alloys Copper, low-alloyed Brass, short-chipping long-chipping Bronze, short-chipping Bronze, long-chipping Duroplastics Thermoplastics Kevlar Glass, carbon concent. plastics
Material examples, new description (old description in brackets) Figures in bold = material no. to DIN EN 1.0035 S185(St33),1.0486 P275N(StE285),1.0345 P235GH(H1),1.0425 P265GH(H2) 1.0050 E295 (St50-2), 1.0070 E360 (St70-2), 1.8937 P500NH (WStE500) 1.0718 11SMnPb30 (9SMnPb28), 1.0736 11SMn37 (9SMn36) 1.0727 46S20 (45S20), 1.0728 (60S20), 1.0757 46SPb20 (45SPb20) 1.0402 C22, 1.1178 C30E (Ck30) 1.0503 C45, 1.1191 C45E (Ck45) 1.0601 C60, 1.1221 C60E (Ck60) 1.5131 50MnSi4, 1.7003 38Cr2, 1.7030 28Cr4 1.5710 36NiCr6, 1.7035 41Cr4, 1.7225 42CrMo4 1.0301 (C10), 1.1121 C10E (Ck10) 1.7043 38Cr4 1.5752 15NiCr13 (15NiCr13), 1.7131 16MnCr5, 1.7264 20CrMo5 1.8504 34CrAl6 1.8519 31CrMoV9, 1.8550 34CrAlNi7 1.1750 C75W, 1.2067 102Cr6, 1.2307 29CrMoV9 1.2080 X210Cr12, 1.2083 X42Cr13, 1.2419 105WCr6, 1.2767 X45NiCrMo4 1.3243 S 6-5-2-5, 1.3343 S 6-5-2, 1.3344 S 6-5-3 1.5026 55Si7, 1.7176 55Cr3, 1.8159 51CrV4 (51CrV4) 1.4005 X12CrS13, 1.4104 X14CrMoS17, 1.4105 X6CrMoS17, 1.4305 X8CrNiS18-9 1.4301 X5CrNi18-10 (V2A), 1.4541 X6CrNiTi18-10, 1.4571 X6CrNiMoTi 17-12-2 (V4A) 1.4057 X20CrNi 17 2 (X17CrNi16-2), 1.4122 X39CrMo17-1, 1.4521 X2CrMoTi18-2 Nimonic, Inconel, Monel, Hastelloy 0.6010 EN-GJL-100(GG10), 0.6020 EN-GJL-200(GG20) 0.6025 EN-GJL-250(GG25), 0.6035 EN-GJL-350(GG35) 0.7050 EN-GJS-500-7(GGG50), 0.8035 EN-GJMW-350-4(GTW35) 0.7070 EN-GJS-700-2(GGG70), 0.8170 EN-GJMB-700-2(GTS70) 3.7024 Ti99,5, 3.7114 TiAl5Sn2,5, 3.7124 TiCu2 3.7154 TiAl6Zr5, 3.7165 TiAl6V4, 3.7184 TiAl4Mo4Sn2,5, - TiAl8Mo1V1 3.0255 Al99,5, 3.2315 AlMgSi1, 3.3515 AlMg1 3.0615 AlMgSiPb, 3.1325 AlCuMg1, 3.3245 AlMg3Si, 3.4365 AlZnMgCu1,5 3.2131 G-AlSi5Cu1, 3.2153 G-AlSi7Cu3, 3.2573 G-AlSi9 3.2581 G-AlSi12, 3.2583 G-AlSi12Cu, - G-AlSi12CuNiMg 3.5200 MgMn2, 3.5812.05 G-MgAl8Zn1, 3.5612.05 G-MgAl6Zn1 2.0070 SE-Cu, 2.1020 CuSn6, 2.1096 G-CuSn5ZnPb 2.0380 CuZn39Pb2, 2.0401 CuZn39Pb3, 2.0410 CuZn43Pb2 2.0250 CuZn20, 2.0280 CuZn33, 2.0332 CuZn37Pb0,5 2.1090 CuSn7ZnPb, 2.1170 CuPb5Sn5, 2.1176 CuPb10Sn 2.0790 CuNi18Zn19Pb 2.0916 CuAl5, 2.0960 CuAl9Mn, 2.1050 CuSn10 2.0980 CuAl11Ni, 2.1247 CuBe2 Bakelit, Resopal, Pertinax, Moltopren Plexiglass, Hostalen, Novodur, Makralon Kevlar GFK/CFK
Tensile strength Hardness MPa (N/mm2) 500 >500-850 850 850-1000 700 700-850 850-1000 850-1000 1000-1200 750 850-1000 1000-1200 850-1000 >1000-1200 850 >850-1000 650-1000 330 HB 850 850 850 40-48 HRC >48-60 HRC 1200 240 HB <300 HB 240 HB <300 HB 350 HB 850 >850-1200 400 450 600 600 450 400 600 600 600 >600-850 850 >850-1000
Coolant
bright
steam tempered
nitrided lands
nitrided
golden brown
TiAlN
94
GUHRINGGUIDE
RT 800 WP
Twist Drills
Indexable inserts
Tool material Carbide grade Surface finish Guh. no. Std. range, page
Carbide
K 2747 570 K/P 1047 570 K/P 2485 570
general steels
Tool holder
Cooling Guh. no. Std. range, page with indexable inserts:
3xD
5242 568
5xD
5243 568
7xD
5248 568
vc m/min 100 85 100 85 100 95 85 85 70 100 85 55 80 55 40 35 40 35 40 30 25 20 20 160 120 120 100 25 30 25 220 200 180 150 200 80 210 140 80 65 50 40 80 80 80 80
Feed col. no. 130 110 130 110 130 125 110 110 90 130 110 70 105 70 55 50 55 50 55 40 35 25 25 210 155 155 130 35 40 35 290 260 235 195 260 105 270 180 105 85 65 55 105 105 105 105
6 5 7 6 6 6 5 6 5 7 6 4
5 4 5 4 3 2 3 3 3 2 2
vc m/min 95 80 95 80 95 90 80 80 65 95 80 55 80 55 40 35 40 35 40 30 25 20 20 150 110 110 90 25 30 25 200 200 170 140 200 80 210 140 80 65 50 40 80 80 80 80
Feed col. no. 125 105 125 105 125 120 105 105 85 125 105 70 105 70 55 50 55 50 55 40 35 25 25 195 145 145 120 35 40 35 260 260 220 180 260 105 270 180 105 85 65 55 105 105 105 105
6 5 7 6 6 6 5 6 5 7 6 4
5 4 5 4 3 2 3 3 3 2 2
vc m/min 90 80 90 80 90 85 75 75 65 90 75 55 80 55 40 35 40 35 40 30 25 20 20 150 110 110 90 25 30 25 200 200 170 140 200 80 210 140 80 65 50 40 80 80 80 80
Feed col. no. 120 105 120 105 120 110 100 100 85 120 100 70 105 70 55 50 55 50 55 40 35 25 25 195 145 145 120 35 40 35 260 260 220 180 260 105 270 180 105 85 65 55 105 105 105 105
5 4 6 5 5 5 4 5 4 6 5 4
4 3 4 3 2 2 2 2 2 1 1
100 80 80 70 10
7 7 7 6
2 3 2 7 7 7 7 6 7 6 6 6 6 5 5 5 5 5
90 70 70 60 10
7 7 7 6
2 3 2 7 7 7 7 6 7 6 6 6 6 5 5 5 5 5
90 70 70 60 10
6 6 6 5
2 2 1 6 6 6 6 5 6 5 5 5 5 4 4 4 4 4
AlTiN
TiCN
FIRE
AlCrN
TiN
MolyGlide
95
Twist Drills
Alloyed heat-treatable steels Unalloyed case hardened steels Alloyed case hardened steels Nitriding steels Tool steels High speed steels Spring steels Stainless steels, sulphured austenitic martensitic Hardened steels Special alloys Cast iron Spheroidal graphite iron and malleable cast iron Chilled cast iron Ti and Ti-alloys Aluminium and Al-alloys Al wrought alloys Al cast alloys 10 % Si > 10 % Si Magnesium alloys Copper, low-alloyed Brass, short-chipping long-chipping Bronze, short-chipping Bronze, long-chipping Duroplastics Thermoplastics Kevlar Glass, carbon concent. plastics
bright
steam tempered
nitrided lands
nitrided
golden brown
TiAlN
96
GUHRINGGUIDE
Drilling depth
Carbide
depend. on index. insert 400560 40<60
vc m/min 110150 100130 110150 100130 100130 90120 80110 80110 70100 90120 80110 70100 80110 70100 70100 7090
Carbide
depend. on index. insert 400560 40<60
vc m/min 100130 90120 100130 90120 90120 80110 70100 70100 6590 80110 70100 6590 70100 6590 6595 6590
Carbide
depend. on index. insert 400560 40<60
vc m/min 70120 70110 70120 70110 80110 70100 6090 6090 6080 70100 6090 6080 6090 6080 6090 6080
Carbide
depend. on index. insert 400560 40<60
vc m/min 60110 60110 60120 60110 70100 6090 5580 5580 5575 6090 5580 5575 5580 5575 5580 5575
600950 60100
vc m/min 130180 120155 130180 120160 120155 110145 100130 100130 85120 110145 100130 85120 100130 85120 85120 85110
600950 60100
vc m/min 120155 110145 120155 110145 110145 100130 85120 85120 80110 100130 85120 80110 85120 80110 80115 80110
600950 60100
vc m/min 85145 85130 85145 85130 100130 85120 70110 70110 70100 85120 70110 70100 70110 70100 70110 70100
600950 60100
vc m/min 70130 70130 70145 70130 85120 70110 65100 65100 6590 70110 65100 6590 65100 6590 65100 6590
AlTiN
TiCN
FIRE
AlCrN
TiN
MolyGlide
97
Twist Drills
6xD
9xD
12xD
Standard
Type
Tool illustration
Surface
Diameter range
Jobber drills
DIN 338
rh
HSS
0.200 - 20.000
205
130
206
DIN 338
rh
HSS
2.370 - 5.300
560
138
207
DIN 338
rh
HSS
0.200 - 19.500
651
131
207
DIN 338
rh
HSS
1.000 - 16.000
2456
135
207
DIN 338
rh
HSCO
0.200 - 20.000
305
134
250
DIN 338
rh
HSCO
1.000 - 14.500
2997
135
251
DIN 338
rh
M42
0.500 - 16.000
1146
138
251
DIN 338
rh
HSS
3.100 - 16.670
240
132
206
DIN 338
rh
HSS
0.200 - 20.000
206
134
206
DIN 338
rh
HSS
0.200 - 20.000
207
134
206
DIN 338
GT 100
rh
HSS
0.600 - 16.000
549
136
207
DIN 338
GT 100
rh
HSS
1.000 - 16.000
652
137
207
DIN 338
GT 100
rh
HSS
1.000 - 16.000
2457
137
207
DIN 338
GT 100
rh
HSCO
1.000 - 16.000
622
136
250
DIN 338
GT 100
rh
HSCO
1.000 - 16.000
658
137
250
bright
steam tempered
nitrided lands
nitrided
golden brown
TiAlN
98
Standard
Type
Tool illustration
Surface
Diameter range
Jobber drills
DIN 338
GT 100
rh
HSCO
1.000 - 16.000
2459
137
251
DIN 338
GT 100
rh
HSCO
3.000 - 12.000
1223
137
251
DIN 338
GT 100
rh
HSCO
2.100 - 12.000
1221
137
250
DIN 338
Ti
rh
HSCO
0.200 - 19.000
605
134
250
DIN 338
Ti
rh
HSCO
0.500 - 14.500
657
135
250
DIN 338
Ti
rh
HSCO
1.000 - 13.000
2458
135
251
DIN 338
VA
rh
HSCO
1.000 - 12.000
1260
134
251
Guhring std.
rh
Solid carbide
1.000 - 12.000
732
102
251
Guhring std.
rh
Solid carbide
1.000 - 12.000
2464
102
251
rh
Carbide
2.700 - 14.000
710
102
251
DIN 338
P2000
rh
HSCO
1.000 - 13.000
2047
134
251
DIN 338
lh
HSS
0.200 - 20.000
208
134
206
DIN 338
lh
HSS
0.250 - 14.250
664
139
207
DIN 338
lh
HSCO
0.320 - 20.000
308
138
250
DIN 338
lh
HSS
0.220 - 20.000
209
134
206
AlTiN
TiCN
FIRE
AlCrN
TiN
MolyGlide
99
Standard
Type
Tool illustration
Surface
Diameter range
Jobber drills
DIN 338
lh
HSS
0.250 - 20.000
210
138
206
DIN 338
GT 100
lh
HSS
1.000 - 16.000
550
138
207
DIN 338
GT 100
lh
HSS
1.400 - 20.000
665
139
207
DIN 338
Ti
lh
HSCO
0.300 - 9.500
608
138
250
Stub drills
DIN 1897
rh
HSS
0.350 - 50.000
223
132
278
DIN 1897
rh
HSS
0.600 - 30.160
653
133
279
DIN 1897
rh
HSS
1.000 - 16.000
2460
133
279
DIN 1897
rh
M42
1.000 - 15.870
1259
138
314
rh
HSCO
0.400 - 48.000
329
134
279
rh
HSCO
0.500 - 15.500
659
135
279
rh
HSCO
1.000 - 19.500
2461
135
279
DIN 1897
VA
rh
HSCO
1.000 - 12.000
1261
138
279
DIN 1897
rh
HSS
0.690 - 22.000
224
138
278
DIN 1897
rh
HSS
1.000 - 20.000
225
138
278
bright
steam tempered
nitrided lands
nitrided
golden brown
TiAlN
100
Standard
Type
Tool illustration
Surface
Diameter range
Stub drills
DIN 1897
GT 80
rh
HSS
1.000 - 20.000
552
136
278
DIN 1897
GT 80
rh
HSCO
1.000 - 20.000
1228
137
279
DIN 1897
GT 80
rh
HSCO
1.000 - 16.000
2498
137
279
rh
PM HSS-E
2.000 - 13.000
515
115
314
DIN 6539
rh
Solid carbide
0.500 - 16.000
730
102
314
DIN 6539
rh
Solid carbide
1.000 - 16.000
2463
102
314
Guhring std.
rh
Solid carbide
0.490 - 6.500
702
102
319
Guhring std.
rh
Solid carbide
0.750 - 11.910
709
102
319
DIN 1897
P2000
rh
HSCO
1.000 - 13.000
2048
135
279
DIN 1897
lh
HSS
0.320 - 50.000
226
134
278
DIN 1897
lh
HSS
0.800 - 19.000
672
139
279
lh
HSCO
0.450 - 35.000
330
138
279
DIN 1897
lh
HSS
0.750 - 29.000
227
138
278
DIN 1897
lh
HSS
1.000 - 20.000
228
138
278
DIN 1897
GT 80
lh
HSS
1.000 - 19.840
553
138
278
AlTiN
TiCN
FIRE
AlCrN
TiN
MolyGlide
101
Standard
Type
Tool illustration
-range mm
Guhring no.
Discount group
Jobber drills
DIN 338
HSS
>2,36
201/ 200
130
324
DIN 338
HSS
201/ 200
130
325
DIN 338
HSCO
>2,36
201/ 200
130
326
DIN 338
HSCO
195
130
326
DIN 338
HSCO
2049
134
327
DIN 1897
HSCO
2050
134
327
Metal case only Metal case only Metal case only Plastic stand only
36 73 72 11
steam tempered
nitrided lands
nitrided
golden brown
TiAlN
102
Standard
Type
Tool illustration
Surface
Diameter range
rh
3.000 - 12.000
1946
102
340
rh
HSCO
2.000 - 20.000
512
115
328
rh
HSCO
2.000 - 20.000
511
115
335
rh
PM HSS-E
2.000 - 13.000
513
115
333
rh
HSS
13.000 - 31.750
268
138
341
rh
HSCO
16.000 - 40.000
128
138
342
Guhring std.
lh
HSCO
17 .500 - 40.000
132
138
342
rh
HSCO
25.000 - 40.000
129
138
343
Guhring std.
lh
HSCO
25.000 - 39.000
136
138
343
NC-spotting drills 90
Guhring std.
rh
HSS
6.350 - 25.400
559
138
345
Guhring std.
rh
HSS
2.950 - 25.400
557
134
344
AlTiN
TiCN
FIRE
AlCrN
TiN
MolyGlide
103
Standard
Type
Tool illustration
Surface
Diameter range
NC-spotting drills 90
Guhring std.
rh
HSS
3.000 - 25.400
568
135
344
Guhring std.
rh
Solid carbide
5.000 - 20.000
723
102
344
rh
HSS
3.000 - 25.400
556
134
346
Guhring std.
rh
HSS
3.000 - 25.400
567
139
346
Guhring std.
rh
Solid carbide
5.000 - 20.000
724
102
346
rh
HSS
1.500 - 10.500
554
134
347
Micro-precision drills
DIN 1899
rh
HSCO
0.050 - 1.920
301
134
349
DIN 1899
rh
HSCO
0.160 - 1.900
660
135
349
Guhring std.
rh
Solid carbide
0.200 - 1.400
701
102
349
Guhring std.
rh
Solid carbide
0.800 - 3.000
6400
164
357
Guhring std.
rh
Solid carbide
0.800 - 3.000
6401
164
359
DIN 1899
lh
HSCO
0.130 - 1.950
303
138
349
bright
steam tempered
nitrided lands
nitrided
golden brown
TiAlN
104
Standard
Type
Tool illustration
Surface
Diameter range
rh
HSS
0.800 - 20.000
211
134
363
DIN 339
rh
HSS
2.400 - 5.000
561
138
363
DIN 339
rh
HSS
1.000 - 13.000
666
139
363
DIN 339
rh
HSCO
1.100 - 19.000
311
138
363
rh
HSS
0.400 - 36.510
217
132
372
DIN 340
rh
HSS
2.400 - 5.000
562
138
373
DIN 340
rh
HSS
0.500 - 22.220
667
133
373
DIN 340
rh
HSS
3.100 - 25.250
204
138
372
DIN 340
rh
HSCO
0.500 - 26.000
317
134
373
DIN 340
rh
HSS
0.460 - 21.000
218
134
372
DIN 340
rh
HSS
0.400 - 24.000
219
134
372
DIN 340
GT 100
rh
HSS
1.000 - 14.000
535
136
373
DIN 340
GT 100
rh
HSS
1.000 - 14.000
668
137
373
DIN 340
GT 100
rh
HSS
1.000 - 10.000
2462
137
373
AlTiN
TiCN
FIRE
AlCrN
TiN
MolyGlide
105
Standard
Type
Tool illustration
Surface
Diameter range
rh
0.500 - 1.500
706
102
402
DIN 340
GT 100
rh
HSCO
1.000 - 12.000
336
136
373
DIN 340
GT 100
rh
HSCO
1.000 - 12.000
396
137
373
DIN 340
GT 50
rh
HSS
1.000 - 14.000
501
136
372
DIN 340
Ti
rh
HSCO
1.000 - 13.000
617
134
373
DIN 340
Ti
rh
HSCO
1.000 - 10.200
669
139
373
DIN 340
lh
HSS
0.450 - 29.000
220
138
372
DIN 340
lh
HSS
0.430 - 17 .100
221
138
372
DIN 340
GT 100
lh
HSS
1.400 - 13.000
506
138
372
rh
HSS
1.600 - 13.000
235
134
403
DIN 1869
GT 50
rh
HSS
2.000 - 12.700
524
138
403
rh
HSS
1.950 - 13.000
502
136
403
rh
HSS
1.980 - 12.700
670
137
403
rh
HSCO
2.700 - 10.000
618
136
403
bright
steam tempered
nitrided lands
nitrided
golden brown
TiAlN
106
Standard
Type
Tool illustration
Surface
Diameter range
rh
HSS
2.700 - 13.000
236
134
408
DIN 1869
GT 50
rh
HSS
2.800 - 12.500
528
138
408
rh
HSS
2.000 - 13.000
503
136
408
rh
HSS
2.700 - 8.500
671
139
408
rh
HSCO
3.000 - 10.000
619
138
408
rh
HSS
3.500 - 13.000
237
138
412
DIN 1869
GT 50
rh
HSS
2.500 - 13.000
529
138
412
rh
HSS
2.500 - 13.000
504
136
412
rh
HSS
6.000 - 12.000
242
136
415
rh
HSS
8.000 - 12.000
243
138
416
rh
HSS
10.000 - 12.000
244
138
417
rh
HSS
1.500 - 8.500
577
138
418
AlTiN
TiCN
FIRE
AlCrN
TiN
MolyGlide
107
Standard
Type
Tool illustration
Surface
Diameter range
rh
HSS
1.500 - 8.000
579
138
418
rh
HSS
1.500 - 8.000
578
138
421
NAS 907
rh
HSS
1.500 - 8.000
580
138
421
Pin drills
DIN 1898
rh
HSS
1.000 - 12.000
531
138
423
rh
Carbide
1.700 - 23.500
703
102
424
Guhring std.
rh
Carbide
1.500 - 24.500
704
102
424
Kevlar drills
Guhring std. Solid carbide
rh
2.380 - 12.000
1149
102
428
rh
Carbide
3.000 - 12.000
707
102
429
Masonry drills
Guhring std.
rh
Carbide
3.000 - 16.000
716
102
430
bright
steam tempered
nitrided lands
nitrided
golden brown
TiAlN
108
Standard
Type
Tool illustration
Surface
Diameter range
rh
axial
HSS
3.000 - 13.000
390
136
362
Guhring GT 80 std. IK
rh
axial
HSCO
5.000 - 20.000
1131
134
361
Guhring GT 80 std. IK
rh
axial
HSCO
5.000 - 20.000
1132
135
361
AlTiN
TiCN
FIRE
AlCrN
TiN
MolyGlide
109
Standard
Type
Tool illustration
Surface
Diameter range
Twist drills
DIN 345
rh
HSS
2.000 - 100.000
245
132
434
DIN 345
rh
HSS
3.000 - 31.000
654
133
435
DIN 345
rh
HSCO
3.000 - 67 .000
345
134
435
DIN 345
rh
HSCO
7 .940 - 31.000
661
139
435
DIN 345
rh
HSS
6.700 - 47 .000
246
138
434
DIN 345
rh
HSS
3.200 - 48.000
247
138
434
DIN 345
VA
rh
HSCO
10.000 - 32.000
1262
134
435
DIN 345
GT 100
rh
HSS
7 .940 - 31.750
558
138
434
DIN 345
GT 100
rh
HSS
7 .940 - 32.000
606
139
435
DIN 345
GT 100
rh
HSCO
9.520 - 32.000
645
138
435
DIN 345
GT 100
rh
HSCO
10.200 - 30.160
662
139
435
DIN 345
GT 100
rh
HSCO
10.000 - 30.160
1224
139
435
DIN 345
GT 100
rh
HSCO
10.400 - 30.160
1222
139
435
DIN 345
rh
HSS
8.000 - 59.000
229
138
434
DIN 345
rh
HSS
10.320 - 23.000
592
138
434
bright
steam tempered
nitrided lands
nitrided
golden brown
TiAlN
110
Standard
Type
Tool illustration
Surface
Diameter range
Twist drills
DIN 346
rh
HSS
10.000 - 76.000
251
138
460
DIN 346
rh
HSCO
10.000 - 30.500
351
138
460
DIN 345
lh
HSS
5.000 - 60.000
248
138
434
Jobber drills
Guhring GV 120 std.
rh
HSCO
7 .000 - 46.000
363
134
431
rh
HSCO
10.500 - 31.000
663
139
431
Guhring std.
VA
rh
HSCO
10.000 - 32.000
1263
138
431
rh
Carbide
8.000 - 50.000
705
102
491
rh
HSS
2.900 - 50.000
257
132
462
DIN 341
rh
HSS
4.200 - 22.000
655
133
462
DIN 341
rh
HSCO
4.750 - 50.000
357
138
462
DIN 341
GT 100
rh
HSS
5.500 - 32.000
551
136
462
DIN 341
GT 100
rh
HSS
6.200 - 23.000
656
139
462
AlTiN
TiCN
FIRE
AlCrN
TiN
MolyGlide
111
Standard
Type
Tool illustration
Surface
Diameter range
GT 100
rh
HSCO
10.000 - 30.500
623
138
462
DIN 341
GT 50
rh
HSS
4.800 - 29.500
505
138
462
Guhring std.
rh
HSS
10.000 - 29.000
523
138
469
rh
HSS
8.000 - 50.000
266
134
478
DIN 1870
GT 50
rh
HSS
7 .900 - 33.000
525
138
478
rh
HSS
8.000 - 32.000
526
136
478
rh
HSCO
9.520 - 30.000
620
138
478
rh
HSS
7 .700 - 45.000
267
138
482
DIN 1870
GT 50
rh
HSS
8.000 - 31.000
542
138
482
rh
HSS
7 .800 - 30.000
527
136
482
rh
HSCO
9.520 - 29.500
621
138
482
rh
HSS
6.000 - 7 .500
563
138
485
bright
steam tempered
nitrided lands
nitrided
golden brown
TiAlN
112
Standard
Type
Tool illustration
Surface
Diameter range
rh
HSS
6.000 - 10.000
564
138
486
rh
HSS
6.000 - 17 .000
565
138
487
rh
HSS
8.000 - 40.000
566
138
485
rh
HSS
14.000 - 40.000
293
138
486
rh
HSS
14.000 - 18.000
298
138
488
rh
HSS
14.000 - 18.000
299
138
489
Pin drills
DIN 1898
rh
HSS
5.000 - 25.000
532
138
490
AlTiN
TiCN
FIRE
AlCrN
TiN
MolyGlide
113
Standard
Type
Tool illustration
Surface
Diameter range
rh
radial
HSS
9.520 - 23.020
269
138
470
rh
axial
HSS
10.000 - 49.000
270
138
473
Guhring std.
rh
radial
HSS
10.000 - 49.000
272
138
473
Guhring std.
rh
radial
HSS
10.000 - 44.000
271
138
473
Guhring std.
rh
DIN 228 BK
HSS
10.000 - 34.000
1101
138
472
rh
axial
HSCO
11.000 - 34.920
370
138
473
rh
radial
HSCO
11.500 - 34.000
372
138
473
rh
radial
HSCO
11.000 - 34.130
371
138
473
rh
axial
HSCO
11.000 - 33.000
374
138
476
rh
radial
HSCO
11.000 - 34.000
376
138
476
rh
radial
HSCO
11.000 - 34.000
375
138
476
bright
steam tempered
nitrided lands
nitrided
golden brown
TiAlN
114
Ratio drills
Drilling Shank Tool material Surface depth design Guhring no. Discount group Standard range, page
Standard
Type
Tool illustration
Diameter range
3xD
DZ
3.300 - 16.000
1798
121
503
3xD
Solid carbide
DZ
3.000 - 15.000
1702
121
503
3xD
Solid carbide
HA
4.600 - 12.500
1659
121
494
3xD
Solid carbide
HA
3.700 - 12.500
2475
121
494
3xD
Solid carbide
DZ
3.000 - 16.000
1242
121
503
3xD
Solid carbide
DZ
3.000 - 16.000
2473
121
503
3xD
Solid carbide
HA
3.000 - 20.000
1673
121
494
3xD
Solid carbide
HA
3.000 - 20.000
2480
121
494
3xD
Solid carbide
HE
3.000 - 20.000
1184
121
494
3xD
Solid carbide
HE
3.000 - 20.000
2472
121
494
5xD
Solid carbide
DZ
5.000 - 16.000
1799
121
507
5xD
Solid carbide
HA
3.000 - 14.000
2712
121
499
5xD
Solid carbide
DZ
5.000 - 16.000
1243
121
507
5xD
Solid carbide
DZ
5.000 - 16.000
2474
121
507
5xD
Solid carbide
HA
3.300 - 16.000
2717
121
499
AlTiN
TiCN
FIRE
AlCrN
TiN
MolyGlide
115
Ratio drills
Ratio drills
Drilling Shank Tool material Surface depth design Guhring no. Discount group Standard range, page
Ratio drills
Standard
Type
Tool illustration
Diameter range
5xD
HA
3.000 - 16.000
2996
121
499
5xD
Solid carbide
HE
3.000 - 16.000
2718
121
499
5xD
Solid carbide
HE
3.000 - 16.000
2719
121
499
3 x D Carbide
HE
9.500 - 25.500
1171
128
543
RT 80 U
5 x D Carbide
HE
9.500 - 25.500
1172
128
546
DIN RT 80 6538 L U
7 x D Carbide
HE
9.500 - 25.000
1173
128
548
4xD
Solid carbide
HA
3.000 - 20.000
768
121
535
4xD
Solid carbide
HA
3.000 - 20.000
6068
121
535
7xD
Solid carbide
HA
3.000 - 20.000
769
121
538
7xD
Solid carbide
HA
3.000 - 20.000
6069
121
538
10 x D
Solid carbide
HA
3.000 - 20.000
770
121
540
10 x D
Solid carbide
HA
3.000 - 19.500
6070
121
540
15 x D
Solid carbide
HA
5.000 - 14.000
773
121
542
3xD
Solid carbide
HA
4.000 - 22.000
1660
121
510
bright
steam tempered
nitrided lands
nitrided
golden brown
TiAlN
116
Ratio drills
Drilling Shank Tool material Surface depth design Guhring no. Discount group Standard range, page
Standard
Type
Tool illustration
Diameter range
3xD
HE
4.000 - 22.500
1180
121
510
3xD
Solid carbide
HE
4.000 - 20.000
2468
121
511
5xD
Solid carbide
HA
4.000 - 24.500
1662
121
520
5xD
Solid carbide
HA
4.000 - 20.000
2478
121
521
5xD
Solid carbide
HE
4.000 - 25.000
1182
121
520
5xD
Solid carbide
HE
4.000 - 20.000
2470
121
520
3xD
Solid carbide
HA
5.000 - 20.000
1661
121
511
3xD
Solid carbide
HA
3.000 - 20.000
2477
121
511
3xD
Solid carbide
HE
4.000 - 20.000
1181
121
511
3xD
Solid carbide
HE
3.000 - 20.000
2469
121
511
5xD
Solid carbide
HA
4.000 - 20.000
1663
121
521
5xD
Solid carbide
HA
3.000 - 20.000
2479
121
521
5xD
Solid carbide
HE
4.000 - 20.000
1183
121
521
5xD
Solid carbide
HE
3.000 - 20.000
2471
121
521
5xD
Solid carbide
HA
3.000 - 20.000
6501
165
521
AlTiN
TiCN
FIRE
AlCrN
TiN
MolyGlide
117
Ratio drills
Ratio drills
Drilling Shank Tool material Surface depth design Guhring no. Discount group Standard range, page
Ratio drills
Standard
Type
Tool illustration
Diameter range
7xD
HA
4.000 - 20.000
6502
165
530
7xD
Solid carbide
HA
5.000 - 20.000
2711
121
530
7xD
Solid carbide
HE
4.000 - 20.000
4044
121
530
7xD
Solid carbide
HE
4.000 - 20.000
4045
121
530
3xD
DZ
3.570 - 19.500
745
109
552
5xD
Solid carbide
DZ
3.100 - 19.500
1024
109
552
5xD
Solid carbide
DZ
3.000 - 20.000
1025
109
553
5xD
Solid carbide
HA
3.000 - 20.000
2713
109
550
5xD
Solid carbide
HA
5.000 - 18.500
2939
109
550
5xD
Solid carbide
DZ
3.000 - 14.400
1027
109
552
5xD
Solid carbide
DZ
3.000 - 20.000
731
109
553
5xD
Solid carbide
DZ
3.000 - 19.000
611
109
553
3xD
Solid carbide
DZ
3.800 - 20.000
1020
109
552
5xD
Solid carbide
DZ
3.500 - 16.500
1028
109
553
bright
steam tempered
nitrided lands
nitrided
golden brown
TiAlN
118
Ratio drills
Drilling Shank Tool material Surface depth design Guhring no. Discount group Standard range, page
Standard
Type
Tool illustration
Diameter range
5xD
DZ
4.400 - 13.100
1029
109
553
5xD
Solid carbide
DZ
3.700 - 17 .000
1021
109
553
DZ
3.400 - 20.000
1032
109
562
Solid carbide
DZ
3.100 - 11.000
1034
109
562
Solid carbide
DZ
4.000 - 20.000
1033
109
562
AlTiN
TiCN
FIRE
AlCrN
TiN
MolyGlide
119
Ratio drills
Tooling system
Standard
Type
Tool illustration
Drilling depth
Tool material
Surface finish
Diameter range
Guhring no.
Chamfer collar FR 90
5.0
16.0
1052
140
582
Guhring FR 90 std.
5.0
18.0
145
140
583
5.0
16.0
1053
140
583
Clamping sleeve
5.0
18.0
1054
140
583
Adjustment ring Guhring FR90 std. Carbide 4.0 20.0 1156 142 582
Carbide
4.0
20.0
1056
142
582
M4 Adjustment element 4.0 Clamping piece T8 Screw driver T8/SW4 - SW5 Torx screw SW4 - SW5 Screw driver
steam tempered nitrided lands nitrided golden brown
4072
140
582
20.0
1055
140
582
1612
114
583
1072
140
583
4912
114
583
bright
TiAlN
120
Standard
Type
Tool illustration
Drilling depth
Tool material
Surface finish
Diameter range
Guhring no.
3xD
11.50 - 25.99
4042
140
564
5xD
11.50 - 25.99
4043
140
564
7xD
11.50 - 25.99
4048
140
564
Carbide
11.50 - 25.50
4024
141
566
Carbide
11.50 - 25.50
4025
141
566
Carbide
11.50 - 25.50
4026
141
566
T20
4071
140
567
Guhring std.
T20
1612
114
567
3xD
5242
140
568
5xD
5243
140
568
7xD
5248
140
568
Carbide
16.00 - 40.50
2747
141
570
Carbide
16.00 - 40.50
1047
141
570
Carbide
16.00 - 40.50
2485
141
570
AlTiN
TiCN
FIRE
AlCrN
TiN
MolyGlide
121
Tooling system
Tooling system
Standard
Type
Tool illustration
Drilling depth
Tool material
Surface finish
Diameter range
Guhring no.
T10
1071
140
571
Guhring std.
T10
1612
114
571
Guhring std.
T10
4917
114
571
Guhring std.
4915
114
571
4512
114
572
4510
114
572
VDI Holder
4355
114
573
Reductions HSK-A/HSK-C
bright
steam tempered
nitrided lands
nitrided
golden brown
TiAlN
122
Standard
Type
Tool illustration
Drilling depth
Tool material
Surface finish
Diameter range
Guhring no.
4549
114
573
Extensions HSK-A
0,5xD/ 2,0xD
4142
114
574
0,5xD/ 2,0xD
4144
114
574
3xD
4148
114
574
Extensions, 15 spiral
3xD
4149
114
574
Extensions, cylindrical
AlTiN
TiCN
FIRE
AlCrN
TiN
MolyGlide
123
Tooling system
Tooling system
Standard
Type
Tool illustration
Drilling depth
Tool material
Surface finish
Diameter range
Guhring no.
1xD
4150
114
576
Drill heads
4164
114
577
Retension spindles Guhring LT800 std. WP T30 Torx-Bits 1/2 Torx key Holder size 400 - 950 4160 114 578 4915 114 577 T45 4188 114 577
Guhring std.
Cartridges
Clamping screws
4189
114
578
Guhring std.
4907
114
578
DIN 6798
4102
114
579
Distance pieces
4168
114
579
Carbide
27 .00 - 34.00
2747
141
580
Carbide
27 .00 - 34.00
1047
141
580
Carbide
27 .00 - 34.00
2485
141
580
bright
steam tempered
nitrided lands
nitrided
golden brown
TiAlN
124
Standard
Type
Tool illustration
Drilling depth
Tool material
Surface finish
Diameter range
Guhring no.
T8 Clamping screw T8 Torx screw driver 1/4 Torx-Bit 1/4 Torque key
1071
140
580
Guhring std.
1612
140
580
4917
140
580
Guhring std.
4915
114
580
LTT
Carbide
insert 05 - 06
4170
142
581
Guhring std.
LTT
Carbide
insert 05 - 06
4171
142
581
Guhring std.
LTT
Carbide
insert 05 - 06
4172
142
581
Guhring std.
LTT
Carbide
insert 05 - 06
4173
142
581
Carbide
insert 09 - 12
4179
142
581
Carbide
insert 09 - 12
4180
142
581
Carbide
insert 09 - 12
4181
142
581
Carbide
insert 09 - 12
4182
142
581
Guhring std.
75o
for insert 05 - 09
4166
114
581
Guhring std.
for insert 05 - 12
6128
122
581
AlTiN
TiCN
FIRE
AlCrN
TiN
MolyGlide
125
Tooling system
Step drills
Cutting direcTool material tion Guhring no. Discount group Standard range, page
Step drills
Standard
Type
Tool illustration
Surface
Diameter range
rh
HSS
8.000 - 40.000
274
138
585
Guhring std.
rh
HSS
8.000 - 40.000
574
138
585
Guhring std.
rh
HSS
8.000 - 20.000
575
138
587
Guhring std.
rh
HSS
14.000 - 40.000
576
138
586
rh
HSS
6.000 - 19.000
378
138
588
Guhring std.
rh
HSS
6.600 - 21.500
1147
138
588
Guhring std.
rh
HSS
6.000 - 18.000
379
138
589
Guhring std.
rh
HSS
3.400 - 13.500
380
138
590
rh
HSS
6.000 - 19.000
536
138
591
DIN 8374
rh
HSS
6.600 - 17 .200
636
138
591
DIN 8378
rh
HSS
3.400 - 13.500
540
138
594
Guhring std.
rh
Solid carbide
4.500 - 11.000
739
102
594
DIN 8376
rh
HSS
6.000 - 18.000
538
138
592
bright
steam tempered
nitrided lands
nitrided
golden brown
TiAlN
126
Step drills
Cutting direcTool material tion Guhring no. Discount group Standard range, page
Standard
Type
Tool illustration
Surface
Diameter range
rh
HSS
6.000 - 8.000
638
138
591
Guhring std.
rh
Solid carbide
6.000 - 18.000
738
102
592
Guhring std.
rh
HSS
5.900 - 17 .500
514
138
593
rh
HSS
11.000 - 29.000
537
138
595
Guhring std.
rh
HSS
11.500 - 30.000
637
138
596
DIN 8379
rh
HSS
9.000 - 22.000
541
138
600
DIN 8377
rh
HSS
10.000 - 33.000
539
138
598
Guhring std.
rh
HSS
10.000 - 26.000
639
138
597
Guhring std.
rh
Carbide
15.000 - 18.000
741
102
598
Guhring std.
rh
HSS
9.400 - 33.000
520
138
599
AlTiN
TiCN
FIRE
AlCrN
TiN
MolyGlide
127
Step drills
Center drills
Cutting direcTool material tion Guhring no. Discount group Standard range, page
Center drills
Standard
Form
Tool illustration
Surface
Diameter range
rh
HSS
0.500 - 12.500
581
132
604
DIN 333
rh
HSS
0.500 - 8.000
613
133
605
DIN 333
rh
HSCO
1.000 - 4.000
381
138
605
Guhring std.
rh
HSS
0.500 - 10.000
281
138
606
Guhring std.
rh
HSS
1.000 - 12.500
590
138
605
Guhring std.
rh
Solid carbide
0.500 - 6.300
736
102
605
Guhring std.
rh
HSS
1.000 - 3.150
280
138
608
B.S. 328
rh
HSS
1.190 - 7 .940
292
138
603
ASA
rh
HSS
1.190 - 7 .940
594
138
601
DIN 333
rh
HSS
1.000 - 10.000
585
138
607
Guhring std.
rh
HSS
1.000 - 6.300
285
138
609
Guhring std.
rh
HSS
1.000 - 8.000
591
138
607
ASA
rh
HSS
1.190 - 6.350
595
138
602
DIN 333
rh
HSS
0.500 - 12.500
583
138
604
DIN 333
rh
HSS
0.800 - 8.000
614
139
605
bright
steam tempered
nitrided lands
nitrided
golden brown
TiAlN
128
Center drills
Cutting direcTool material tion Guhring no. Discount group
Standard
Form
Tool illustration
Surface
Diameter range
rh
HSS
0.500 - 10.000
283
138
606
DIN 333
lh
HSS
0.500 - 12.500
582
138
604
Guhring std.
lh
HSS
0.500 - 5.000
282
138
606
B.S. 328
lh
HSS
1.190 - 7 .940
294
138
603
DIN 333
lh
HSS
1.000 - 10.000
586
138
607
Guhring std.
lh
HSS
2.000 - 3.150
286
138
609
DIN 333
lh
HSS
0.800 - 5.000
584
138
604
Guhring std.
lh
HSS
1.250 - 4.000
284
138
606
rh
HSS
1.600 - 12.500
587
138
610
Guhring std.
rh
HSS
1.600 - 10.000
287
138
611
Guhring std.
rh
HSS
1.600 - 10.000
589
138
612
Guhring std.
rh
HSS
1.600 - 5.000
289
138
613
Guhring std.
rh
HSS
1.600 - 10.000
588
138
610
Guhring std.
rh
HSS
1.600 - 8.000
288
138
611
AlTiN
TiCN
FIRE
AlCrN
TiN
MolyGlide
129
Center drills
Core drills
Cutting direcTool material tion Guhring no. Discount group Standard range, page
Core drills
Standard
Type
Tool illustration
Surface
Diameter range
rh
HSS
3.800 - 20.000
533
138
615
Guhring std.
rh
Carbide
3.800 - 19.700
750
102
614
rh
HSS
7 .800 - 50.000
534
138
619
DIN 343
rh
HSCO
7 .800 - 34.600
634
138
619
DIN 8043
rh
Carbide
13.000 - 40.000
729
102
618
DIN 1864
rh
HSS
5.000 - 30.000
555
138
624
DIN 1864
rh
HSCO
8.000 - 24.000
635
138
624
rh
Carbide
35.000 - 75.000
728
102
626
bright
steam tempered
nitrided lands
nitrided
golden brown
TiAlN
130
Standard
Type
Tool illustration
Tool material
Surface finish
Diameter range
Guhring no.
40.0
- 120.0
230
138
632
13.0
50.0
1438
105
627
634
637
AlTiN
TiCN
FIRE
AlCrN
TiN
MolyGlide
131
Drilling tools
Jobber drills
Standard drill
alloyed/unall. steel and cast steel grey cast iron, malleable cast iron spheroidal cast iron sintered powder metal German silver graphite
Surface Type N Cutting direction rh Point grinding Relieved cone Point angle 118 Web thinned 1.00 Standard range, page 206
Jobber drills
Standard drill
hard and crumbly materials brass, magnesium alloys bronze, phosphor bronze electron (thin sections) slate, mica, perspex
Surface Type H Cutting direction rh Point grinding Relieved cone Point angle 118 Web thinned 14.01 Standard range, page 206
Jobber drills
Standard drill
soft and long chipping materials aluminium, long chipping al-alloys zinc, refined copper, silumin electron, soft synthetic mat. wood
Surface Type W Cutting direction rh Point grinding Relieved cone Point angle 130 Web thinned 14.01 Standard range, page 206
Jobber drills
Standard drill
alloyed/unall. steel and cast steel grey cast iron, malleable cast iron spheroidal cast iron sintered powder metal German silver graphite
Surface Type N Cutting direction lh Point grinding Relieved cone Point angle 118 Web thinned 14.01 Standard range, page 206
Jobber drills
Standard drill
hard and crumbling materials brass, magnesium alloys bronze, phosphor bronze slate mica, pertinax
Surface Type H Cutting direction lh Point grinding Relieved cone Point angle 118 Web thinned 14.01 Standard range, page 206
bright
steam tempered
nitrided lands
nitrided
golden brown
TiAlN
132
Surface Type W Cutting direction lh Point grinding Relieved cone Point angle 130 Web thinned 14.01 Standard range, page 206
Jobber drills
alloyed/unall. steel and cast steel grey cast iron, malleable cast iron spheroidal cast iron sintered powder metal German silver graphite
Surface Type N Cutting direction rh Point grinding Relieved cone Point angle 118 Web thinned 3.00 Standard range, page 206
Jobber drills
steels and cast iron up to 1000 N/mm Not recommended for: CrNi steels, stainless steels
Surface Type GT 100 Cutting direction rh Point grinding Relieved cone Point angle 130 Web thinned 0.96 Standard range, page 207
Jobber drills
steels and cast iron up to 1000 N/mm Not recommended for: CrNi steels, stainless steels
Surface Type GT 100 Cutting direction lh Point grinding Relieved cone Point angle 130 Web thinned 1.00 Standard range, page 207
Jobber drills
Standard drill
alloyed/unall. steel and cast steel grey cast iron, malleable cast iron spheroidal cast iron sintered powder metal German silver graphite
Surface Type N Cutting direction rh Point grinding Relieved cone Point angle 118 Web thinned 2.37 Standard range, page 207
AlTiN
TiCN
FIRE
AlCrN
TiN
MolyGlide
133
Jobber drills
Standard drill
alloyed/unall. steel and cast steel grey cast iron, malleable cast iron spheroidal cast iron sintered powder metal German silver graphite
Surface Type N Cutting direction rh Point grinding Relieved cone Point angle 118 Web thinned 1.00 Standard range, page 207
Jobber drills
steels and cast iron up to 1000 N/mm Not recommended for: CrNi steels, stainless steels
Surface Type GT 100 Cutting direction rh Point grinding Relieved cone Point angle 130 Web thinned 1.00 Standard range, page 207
Jobber drills
Standard drill
alloyed/unall. steel and cast steel grey cast iron, malleable cast iron spheroidal cast iron sintered powder metal German silver graphite
Surface Type N Cutting direction lh Point grinding Relieved cone Point angle 118 Web thinned 2.37 Standard range, page 207
Jobber drills
steels and cast iron up to 1000 N/mm Not recommended for: CrNi steels, stainless steels
Surface Type GT 100 Cutting direction lh Point grinding Relieved cone Point angle 130 Web thinned 1.30 Standard range, page 207
Jobber drills
Standard drill
alloyed/unall. steel and cast steel grey cast iron, malleable cast iron spheroidal cast iron sintered powder metal German silver graphite
Surface Type N Cutting direction rh Point grinding Relieved cone Point angle 118 Web thinned 1.00 Standard range, page 207
bright
steam tempered
nitrided lands
nitrided
golden brown
TiAlN
134
Surface Type GT 100 Cutting direction rh Point grinding Relieved cone Point angle 130 Web thinned 1.00 Standard range, page 207
Jobber drills
alloyed and unalloyed steels castings over 800 N/mm hot and cold-rolled steels case hardening steels heat treatable steels
Surface Type N Cutting direction rh Point grinding Relieved cone Point angle 118 Web thinned 1.00 Standard range, page 250
Jobber drills
alloyed and unalloyed steels castings over 800 N/mm hot and cold-rolled steels case hardening steels heat treatable steels
Surface Type N Cutting direction lh Point grinding Relieved cone Point angle 118 Web thinned 2.37 Standard range, page 250
Jobber drills
titanium and titanium alloys stainl./acid-/heat-res. austen. steels high tensile short chipping steels over 900 N/mm Hastelloy/Inconel/Nimonic
Surface Type Ti Cutting direction rh Point grinding Relieved cone Point angle 130 Web thinned 0.96 Standard range, page 250
Jobber drills
titanium and titanium alloys stainl./acid-/heat-res. austen. steels high tensile short chipping steels over 900 N/mm Hastelloy/Inconel/Nimonic
Surface Type Ti Cutting direction lh Point grinding Relieved cone Point angle 130 Web thinned 0.96 Standard range, page 250
AlTiN
TiCN
FIRE
AlCrN
TiN
MolyGlide
135
Jobber drills
Co-alloyed high speed steel Wide flutes Increased wear resistance Especially for drilling depths over 3xD
alloyed and unalloyed steels castings over 800 N/mm hot and cold-rolled steels case hardening steels heat treatable steels
Surface Type GT 100 Cutting direction rh Point grinding Relieved cone Point angle 130 Web thinned 0.96 Standard range, page 250
Jobber drills
titanium and titanium alloys stainl./acid-/heat-res. austen. steels high tensile short chipping steels over 900 N/mm Hastelloy/Inconel/Nimonic
Surface Type Ti Cutting direction rh Point grinding Relieved cone Point angle 130 Web thinned 0.96 Standard range, page 250
Jobber drills
Co-alloyed high speed steel Wide flutes Increased wear resistance Especially for drilling depths over 3xD
alloyed and unalloyed steels castings over 800 N/mm hot and cold-rolled steels case hardening steels heat treatable steels
Surface Type GT 100 Cutting direction rh Point grinding Relieved cone Point angle 130 Web thinned 1.00 Standard range, page 250
Jobber drills
Co-alloyed high speed steel Wide flutes Increased wear resistance Especially for drilling depths over 3xD
alloyed and unalloyed steels castings over 800 N/mm hot and cold-rolled steels case hardening steels heat treatable steels
Surface Type GT 100 Cutting direction rh Point grinding Relieved cone Point angle 130 Web thinned 2.10 Standard range, page 250
Jobber drills
Co-alloyed high speed steel Wide flutes Increased wear resistance Especially for drilling depths over 3xD
alloyed and unalloyed steels castings over 800 N/mm hot and cold-rolled steels case hardening steels heat treatable steels
Surface Type GT 100 Cutting direction rh Point grinding Relieved cone Point angle 130 Web thinned 3.00 Standard range, page 251
bright
steam tempered
nitrided lands
nitrided
golden brown
TiAlN
136
Surface Type VA Cutting direction rh Point grinding Relieved cone Point angle 130 Web thinned Standard range, page 251
Jobber drills
Surface Type P2000 Cutting direction rh Point grinding Relieved cone Point angle 118 Web thinned Standard range, page 251
Jobber drills
titanium and titanium alloys stainl./acid-/heat-res. austen. steels high tensile short chipping steels over 900 N/mm Hastelloy/Inconel/Nimonic
Surface Type Ti Cutting direction rh Point grinding Relieved cone Point angle 130 Web thinned 1.00 Standard range, page 251
Jobber drills
Co-alloyed high speed steel Wide flutes Increased wear resistance Especially for drilling depths over 3xD
alloyed and unalloyed steels castings over 800 N/mm hot and cold-rolled steels case hardening steels heat treatable steels
Surface Type GT 100 Cutting direction rh Point grinding Relieved cone Point angle 130 Web thinned 1.00 Standard range, page 251
Jobber drills
alloyed and unalloyed steels castings over 800 N/mm hot and cold-rolled steels case hardening steels heat treatable steels
Surface Type N Cutting direction rh Point grinding Relieved cone Point angle 118 Web thinned 1.00 Standard range, page 251
AlTiN
TiCN
FIRE
AlCrN
TiN
MolyGlide
137
Jobber drills
medium and high-strength CrNi base alloys Hastelloy, Inconel, Monel, Nimonic stainless/acid-/heat-resistant steels wear-resistant sheet metal steels, bronzes up to 1400 N/mm
Surface Type N Cutting direction rh Point grinding Relieved cone Point angle 135 Web thinned 0.96 Standard range, page 251
Jobber drills
abrasive materials heat treated/hardened steels hard cast iron, manganese steels hard bronze
Surface Type Duro 150 Cutting direction rh Point grinding Facet point Point angle 118 Web thinned 2.70 Standard range, page 251
Jobber drills
Guhring no. 732 Standard Guhring std. Tool material Solid carbide
Standard drill
abrasive materials AlSi alloys fiber-reinforced plastics Duroplastics liable to cause severe abrasion on cutting lips and lands high tensile steels, cast steel grey cast iron, chilled cast iron, CrNi-steels, bronzes, light metals
Surface Type N Cutting direction rh Point grinding Facet point Point angle 118 Web thinned 2.00 Standard range, page 251
Jobber drills
Guhring no. 2464 Standard Guhring std. Tool material Solid carbide
Standard drill
abrasive materials AlSi alloys fiber-reinforced plastics Duroplastics liable to cause severe abrasion on cutting lips and lands high tensile steels, cast steel grey cast iron, chilled cast iron, CrNi-steels, bronzes, light metals
Surface Type N Cutting direction rh Point grinding Facet point Point angle 118 Web thinned 2.00 Standard range, page 251
Stub drills
Rigid twist drill For use in automatic/capstan lathes Also for hand drilling machines
Surface Type N Cutting direction rh Point grinding Relieved cone Point angle 118 Web thinned 1.00 Standard range, page 278
bright
steam tempered
nitrided lands
nitrided
golden brown
TiAlN
138
Surface Type H Cutting direction rh Point grinding Relieved cone Point angle 118 Web thinned 14.01 Standard range, page 278
Stub drills
Surface Type W Cutting direction rh Point grinding Relieved cone Point angle 130 Web thinned 2.37 Standard range, page 278
Stub drills
Surface Type N Cutting direction lh Point grinding Relieved cone Point angle 118 Web thinned 14.01 Standard range, page 278
Stub drills
hard and crumbly materials brass, magnesium alloys bronze, phosphor bronze electron (thin sections) slate, mica, perspex
Surface Type H Cutting direction lh Point grinding Relieved cone Point angle 118 Web thinned 14.01 Standard range, page 278
Stub drills
Surface Type W Cutting direction lh Point grinding Relieved cone Point angle 130 Web thinned 2.37 Standard range, page 278
AlTiN
TiCN
FIRE
AlCrN
TiN
MolyGlide
139
Stub drills
free-cutting steels stainless/acid-resistant steels case hardening/heat treatable steels up to 800 N/mm short/medium chip length Al/Cu alloys
Surface Type GT 80 Cutting direction rh Point grinding Relieved cone Point angle 130 Web thinned 1.00 Standard range, page 278
Stub drills
free-cutting steels stainless/acid-resistant steels case hardening/heat treatable steels up to 800 N/mm short/medium chip length Al/Cu alloys
Surface Type GT 80 Cutting direction lh Point grinding Relieved cone Point angle 130 Web thinned 1.00 Standard range, page 278
Stub drills
Rigid twist drill For use in automatic/capstan lathes Also for hand drilling machines
Surface Type N Cutting direction rh Point grinding Relieved cone Point angle 118 Web thinned 1.00 Standard range, page 279
Stub drills
Surface Type N Cutting direction lh Point grinding Relieved cone Point angle 118 Web thinned 2.37 Standard range, page 279
Stub drills
Rigid twist drill For use in automatic/capstan lathes Also for hand drilling machines
Surface Type N Cutting direction rh Point grinding Relieved cone Point angle 118 Web thinned 1.00 Standard range, page 279
bright
steam tempered
nitrided lands
nitrided
golden brown
TiAlN
140
Surface Type GV 120 Cutting direction rh Point grinding Relieved cone Point angle 130 Web thinned 1.00 Standard range, page 279
Stub drills
Surface Type GV 120 Cutting direction lh Point grinding Relieved cone Point angle 130 Web thinned 2.37 Standard range, page 279
Stub drills
Surface Type GV 120 Cutting direction rh Point grinding Relieved cone Point angle 130 Web thinned 1.00 Standard range, page 279
Stub drills
Co-alloyed high speed steel Special geometry Increased wear resistance For higher tensile steels
long chipping materials up to 1000 N/mm Al and Cu alloys soft bronzes electrolytic copper ductile brass
Surface Type GT 80 Cutting direction rh Point grinding Relieved cone Point angle 130 Web thinned 1.00 Standard range, page 279
Stub drills
Surface Type VA Cutting direction rh Point grinding Relieved cone Point angle 130 Web thinned Standard range, page 279
AlTiN
TiCN
FIRE
AlCrN
TiN
MolyGlide
141
Stub drills
Co-alloyed high speed steel Increased wear resistance Universal application For professional use For hand drilling machines
long chipping steels up tp 1000 N/mm cast iron and AlSi alloys
Surface Type P2000 Cutting direction rh Point grinding Relieved cone Point angle 118 Web thinned Standard range, page 279
Stub drills
Surface Type GV 120 Cutting direction rh Point grinding Relieved cone Point angle 130 Web thinned 1.00 Standard range, page 279
Stub drills
long chipping materials up to 1000 N/mm Al and Cu alloys soft bronzes electrolytic copper ductile brass
Surface Type GT 80 Cutting direction rh Point grinding Relieved cone Point angle 130 Web thinned 1.00 Standard range, page 279
Stub drills
medium/high-strength CrNi-based alloys Hastelloy, Inconel, Nimonic stainless/acid-/heat-resistant steels wear-resistant sheet metals steels, bronzes up to 1400 N/mm
Surface Type N Cutting direction rh Point grinding Relieved cone Point angle 135 Web thinned 1.00 Standard range, page 314
Stub drills
PM Co-alloyed high speed steel Especially high rigidity Especially high wear resistance
high alloyed steels heat treatable and case hardened steels cast iron, brass, bronze
Surface Type GT 500 Cutting direction rh Point grinding Relieved cone Point angle 130 Web thinned 2.00 Standard range, page 314
bright
steam tempered
nitrided lands
nitrided
golden brown
TiAlN
142
Surface Type N Cutting direction rh Point grinding Facet point Point angle 118 Web thinned 2.00 Standard range, page 314
Stub drills
Guhring no. 2463 Standard DIN 6539 Tool material Solid carbide
abrasive materials AlSi alloys fiber-reinforced plastics Duroplastics liable to cause severe abrasion on cutting lips and lands high tensile steels, cast steel grey cast iron, chilled cast iron, CrNi-steels, bronzes, light metals
Surface Type N Cutting direction rh Point grinding Facet point Point angle 118 Web thinned 2.00 Standard range, page 314
Stub drills
Guhring no. 702 Standard Guhring std. Tool material Solid carbide
Special drill
fiberglass reinforced plastics Duroplastics that cause wear on lands and cutting edges
Surface Type N Cutting direction rh Point grinding Facet point Point angle 130 Web thinned Standard range, page 319
Stub drills
Guhring no. 709 Standard Guhring std. Tool material Solid carbide
high tensile steels cast iron, grey cast iron, chilled cast iron austenitic manganese steel CrNi steels bronzes light and non-ferrous metals
Surface Type N Cutting direction rh Point grinding Facet point Point angle 130 Web thinned Standard range, page 319
Co-alloyed high speed steel Low feed force required Low torque required Universal application
alloyed/unalloyed steels up to 800 N/mm cold/hot work steels bearing steels non-ferrous metals cast materials stainless steels plastics
Surface Type GU 500 Cutting direction rh Point grinding Facet point Point angle 118 Web thinned 2.00 Standard range, page 328
AlTiN
TiCN
FIRE
AlCrN
TiN
MolyGlide
143
PM Co-alloyed high speed steel Especially high rigidity Especially high wear resistance
high alloyed steels heat treatable and case hardened steels cast iron, brass, bronze
Surface Type GT 500 Cutting direction rh Point grinding Relieved cone Point angle 130 Web thinned 2.00 Standard range, page 333
Co-alloyed high speed steel Low feed force required Low torque required Increased wear resistance Universal application
alloyed/unall. steels up to 800 N/mm cold and hot work steels bearing steels non-ferrous metals cast materials plastics
Surface Type GU 500 Cutting direction rh Point grinding Facet point Point angle 118 Web thinned 2.00 Standard range, page 335
Guhring no. 1946 Standard DIN 6537 K Tool material Solid carbide
Surface Type H Cutting direction rh Point grinding Facet point Point angle 120 Web thinned 3.00 Standard range, page 340
alloyed/unall. steel and cast steel grey cast iron, malleable cast iron spheroidal cast iron sintered powder iron German silver, graphite
Surface Type N Cutting direction rh Point grinding Relieved cone Point angle 118 Web thinned 14.01 Standard range, page 341
Co-alloyed high speed steel Increased wear resistance With solid shank
Surface Type N Cutting direction rh Point grinding without Point angle 118 Web thinned Standard range, page 342
bright
steam tempered
nitrided lands
nitrided
golden brown
TiAlN
144
Surface Type N Cutting direction lh Point grinding without Point angle 118 Web thinned Standard range, page 342
Co-alloyed high speed steel Increased wear resistance With solid shank
Surface Type N Cutting direction rh Point grinding without Point angle 118 Web thinned Standard range, page 343
Co-alloyed high speed steel Increased wear resistance With solid shank
Surface Type N Cutting direction lh Point grinding without Point angle 118 Web thinned Standard range, page 343
NC-spotting drills 90
Surface Type N Cutting direction rh Point grinding Relieved cone Point angle 90 Web thinned Standard range, page 344
NC-spotting drills 90
Surface Type N Cutting direction rh Point grinding Relieved cone Point angle 90 Web thinned Standard range, page 344
AlTiN
TiCN
FIRE
AlCrN
TiN
MolyGlide
145
NC-spotting drills 90
Guhring no. 723 Standard Guhring std. Tool material Solid carbide
high tensile steels cast iron, grey cast iron, chilled cast iron austenitic manganese steel CrNi steels bronzes light and non-ferrous metals
Surface Type N Cutting direction rh Point grinding Facet point Point angle 90 Web thinned Standard range, page 344
NC-spotting drills 90
Surface Type N Cutting direction rh Point grinding Relieved cone Point angle 90 Web thinned Standard range, page 345
Surface Type N Cutting direction rh Point grinding Relieved cone Point angle 120 Web thinned Standard range, page 346
Surface Type N Cutting direction rh Point grinding Relieved cone Point angle 120 Web thinned Standard range, page 346
Guhring no. 724 Standard Guhring std. Tool material Solid carbide
high tensile steels cast iron, grey cast iron, chilled cast iron austenitic manganese steel CrNi steels bronzes light and non-ferrous metals
Surface Type N Cutting direction rh Point grinding Facet point Point angle 120 Web thinned Standard range, page 346
bright
steam tempered
nitrided lands
nitrided
golden brown
TiAlN
146
Surface Type DK 77 Cutting direction rh Point grinding Relieved cone Point angle 118 Web thinned 1.45 Standard range, page 347
Micro-precision drills
Surface Type N Cutting direction rh Point grinding Facet point Point angle 118 Web thinned Standard range, page 349
Micro-precision drills
Surface Type N Cutting direction lh Point grinding Facet point Point angle 118 Web thinned Standard range, page 349
Micro-precision drills
Co-alloyed high speed steel With re-inforced shank Increased wear resistance
Surface Type N Cutting direction rh Point grinding Facet point Point angle 118 Web thinned Standard range, page 349
Micro-precision drills
Guhring no. 701 Standard Guhring std. Tool material Solid carbide
fiberglass reinforced plastics Duroplastics that cause wear on lands and cutting edges
Surface Type N Cutting direction rh Point grinding Facet point Point angle 130 Web thinned 0.80 Standard range, page 349
AlTiN
TiCN
FIRE
AlCrN
TiN
MolyGlide
147
Micro-precision drills
Guhring no. 6400 Standard Guhring std. Tool material Solid carbide
Surface Type N Cutting direction rh Point grinding Facet point Point angle 140 Web thinned 0.80 Standard range, page 357
Micro-precision drills
Guhring no. 6401 Standard Guhring std. Tool material Solid carbide
Surface Type N Cutting direction rh Point grinding Facet point Point angle 140 Web thinned 0.80 Standard range, page 359
long chipping materials steels up to 1000 N/mm stainless steels cast materials non-ferrous metals
Surface Type GT 80 IK Cutting direction rh Point grinding Relieved cone Point angle 130 Web thinned 5.00 Standard range, page 361
long chipping materials steels up to 1000 N/mm stainless steels cast materials non-ferrous metals
Surface Type GT 80 IK Cutting direction rh Point grinding Relieved cone Point angle 130 Web thinned 5.00 Standard range, page 361
Oil feed drill For drilling through drill bushes Especially for drilling depth over 5xD
laminated sheet metal steel, cast iron, grey cast iron austenitic steels up to 800 N/mm
Surface Type N Cutting direction rh Point grinding Relieved cone Point angle 130 Web thinned 3.00 Standard range, page 362
bright
steam tempered
nitrided lands
nitrided
golden brown
TiAlN
148
Surface Type N Cutting direction rh Point grinding Relieved cone Point angle 118 Web thinned 1.00 Standard range, page 363
alloyed/unall. steel and cast steel grey cast iron, malleable cast iron spheroidal cast iron sintered powder metal German silver graphite
Surface Type N Cutting direction rh Point grinding Relieved cone Point angle 118 Web thinned 2.40 Standard range, page 363
alloyed/unall. steel and cast steel grey cast iron, malleable cast iron spheroidal cast iron sintered powder metal German silver graphite
Surface Type N Cutting direction rh Point grinding Relieved cone Point angle 118 Web thinned 1.00 Standard range, page 363
Co-alloyed high speed steel Special geometry Increased wear resistance For drilling through drill bushes
alloyed/unalloyed steels and castings up to 800 N/mm cold/hot work steels bearing steels high-alloyed steels case hardening/heat treatable steels
Surface Type N Cutting direction rh Point grinding Relieved cone Point angle 118 Web thinned 1.10 Standard range, page 363
With tang
alloyed/unall. steel and cast steel grey cast iron, malleable cast iron spheroidal cast iron sintered powder iron German silver, graphite
Surface Type N Cutting direction rh Point grinding Relieved cone Point angle 118 Web thinned 2.95 Standard range, page 372
AlTiN
TiCN
FIRE
AlCrN
TiN
MolyGlide
149
alloyed/unall. steel and cast steel grey cast iron, malleable cast iron spheroidal cast iron sintered powder iron German silver, graphite
Surface Type N Cutting direction rh Point grinding Relieved cone Point angle 118 Web thinned 1.00 Standard range, page 372
hard, crumbly materials brass, magnesium alloys bronze, phosphor bronze thin zamac and electron slate, mico, pertinax with special point grind: insulating materials, ebonite, bakelite galalithe, celluloid, synthetic resins horn compounds, eternit, plexiglass
Surface Type H Cutting direction rh Point grinding Relieved cone Point angle 118 Web thinned 14.01 Standard range, page 372
soft and long chipping materials aluminium, long chipping al-alloys zinc, refined copper, silumin electron, zamak, soft synthetic mat. wood
Surface Type W Cutting direction rh Point grinding Relieved cone Point angle 130 Web thinned 14.01 Standard range, page 372
Standard drill For drilling through drill bushes Especially for deep holes
alloyed/unall. steel and cast steel grey cast iron, malleable cast iron spheroidal cast iron sintered powder iron German silver, graphite
Surface Type N Cutting direction lh Point grinding Relieved cone Point angle 118 Web thinned 14.01 Standard range, page 372
hard, crumbly materials brass, magnesium alloys bronze, phosphor bronze thin zamac and electron slate, mico, pertinax with special point grind: insulating materials, ebonite, bakelite galalithe, celluloid, synthetic resins horn compounds, eternit, plexiglass
Surface Type H Cutting direction lh Point grinding Relieved cone Point angle 118 Web thinned 14.01 Standard range, page 372
bright
steam tempered
nitrided lands
nitrided
golden brown
TiAlN
150
Surface Type GT 50 Cutting direction rh Point grinding Relieved cone Point angle 130 Web thinned 2.37 Standard range, page 372
steels and cast iron up to 1000 N/mm Not recommended for: CrNi steels, stainless steels
Surface Type GT 100 Cutting direction lh Point grinding Relieved cone Point angle 130 Web thinned 1.40 Standard range, page 372
steels and cast iron up to 1000 N/mm Not recommended for: CrNi steels, stainless steels
Surface Type GT 100 Cutting direction rh Point grinding Relieved cone Point angle 130 Web thinned 1.00 Standard range, page 373
Standard drill For drilling through drill bushes Especially for deep holes
alloyed/unall. steel and cast steel grey cast iron, malleable cast iron spheroidal cast iron sintered powder iron German silver, graphite
Surface Type N Cutting direction rh Point grinding Relieved cone Point angle 118 Web thinned 2.40 Standard range, page 373
Standard drill For drilling through drill bushes Especially for deep holes
alloyed/unall. steel and cast steel grey cast iron, malleable cast iron spheroidal cast iron sintered powder iron German silver, graphite
Surface Type N Cutting direction rh Point grinding Relieved cone Point angle 118 Web thinned 0.96 Standard range, page 373
AlTiN
TiCN
FIRE
AlCrN
TiN
MolyGlide
151
steels and cast iron up to 1000 N/mm Not recommended for: CrNi steels, stainless steels
Surface Type GT 100 Cutting direction rh Point grinding Relieved cone Point angle 130 Web thinned 1.00 Standard range, page 373
steels and cast iron up to 1000 N/mm Not recommended for: CrNi steels, stainless steels
Surface Type GT 100 Cutting direction rh Point grinding Relieved cone Point angle 130 Web thinned 1.00 Standard range, page 373
alloyed/unalloyed steels and castings up to 800 N/mm cold/hot work steels bearing steels high-alloyed steels case hardening/heat treatable steels
Surface Type N Cutting direction rh Point grinding Relieved cone Point angle 118 Web thinned 1.00 Standard range, page 373
Co-alloyed high speed steel Wide flutes Increased wear resistance For unsatisfactory chip evacuation
alloyed and unalloyed steels and castings over 800 N/mm hot and cold rolled steels antifriction bearing steels high alloyed steels case hardening and heat-treatable steels
Surface Type GT 100 Cutting direction rh Point grinding Relieved cone Point angle 130 Web thinned 1.00 Standard range, page 373
Co-alloyed high speed steel Wide flutes Especially high wear resistance For unsatisfactory chip evacuation
alloyed and unalloyed steels and castings over 800 N/mm hot and cold rolled steels antifriction bearing steels high alloyed steels case hardening and heat-treatable steels
Surface Type GT 100 Cutting direction rh Point grinding Relieved cone Point angle 130 Web thinned 1.00 Standard range, page 373
bright
steam tempered
nitrided lands
nitrided
golden brown
TiAlN
152
Surface Type Ti Cutting direction rh Point grinding Relieved cone Point angle 130 Web thinned 1.00 Standard range, page 373
titanium and titanium alloys stainless steels acid and heat resisting austen. steels for high tensile strength and short chipping steels over appr. 900 N/mm antifriction bearing steel Hastelloy, Inconel, Nimonic
Surface Type Ti Cutting direction rh Point grinding Relieved cone Point angle 130 Web thinned 1.00 Standard range, page 373
Guhring no. 706 Standard Guhring std. Tool material Solid carbide
fiberglass reinforced plastics Duroplastics that cause wear on lands and cutting edges
Surface Type N Cutting direction rh Point grinding Relieved cone Point angle 130 Web thinned Standard range, page 402
alloyed/unall. steel and cast steel grey cast iron, malleable cast iron spheroidal cast iron sintered powder metal German silver graphite
Surface Type N Cutting direction rh Point grinding Relieved cone Point angle 118 Web thinned 2.37 Standard range, page 403
steels and cast iron up to 1000 N/mm Not recommended for: CrNi steels, stainless steels
Surface Type GT 100 Cutting direction rh Point grinding Relieved cone Point angle 130 Web thinned 1.95 Standard range, page 403
AlTiN
TiCN
FIRE
AlCrN
TiN
MolyGlide
153
soft and long chipping materials of 500 N/mm mild steel aluminium, aluminium alloys zinc, refined copper, silumin, electron zamak, argalium, soft synthetic mat. wood
Surface Type GT 50 Cutting direction rh Point grinding Relieved cone Point angle 130 Web thinned 2.37 Standard range, page 403
Wide flutes For extremely deep holes For unsatisfactory chip evacuation
steels and cast iron up to 1000 N/mm Not recommended for: CrNi steels, stainless steels
Surface Type GT 100 Cutting direction rh Point grinding Relieved cone Point angle 130 Web thinned 1.98 Standard range, page 403
Co-alloyed high speed steel Wide flutes Increased wear resistance For extremely deep holes For unsatisfactory chip evacuation
high tensile steels and cast steels grey cast iron malleable and spheroidal iron
Surface Type GT 100 Cutting direction rh Point grinding Relieved cone Point angle 130 Web thinned 2.70 Standard range, page 403
alloyed/unall. steel and cast steel grey cast iron, malleable cast iron spheroidal cast iron sintered powder metal German silver graphite
Surface Type N Cutting direction rh Point grinding Relieved cone Point angle 118 Web thinned 2.70 Standard range, page 408
Wide flutes For extremely deep holes For unsatisfactory chip evacuation
steels and cast iron up to 1000 N/mm Not recommended for: CrNi steels, stainless steels
Surface Type GT 100 Cutting direction rh Point grinding Relieved cone Point angle 130 Web thinned 2.00 Standard range, page 408
bright
steam tempered
nitrided lands
nitrided
golden brown
TiAlN
154
Surface Type GT 50 Cutting direction rh Point grinding Relieved cone Point angle 130 Web thinned 2.80 Standard range, page 408
Wide flutes For extremely deep holes For unsatisfactory chip evacuation
steels and cast iron up to 1000 N/mm Not recommended for: CrNi steels, stainless steels
Surface Type GT 100 Cutting direction rh Point grinding Relieved cone Point angle 130 Web thinned 2.30 Standard range, page 408
Co-alloyed high speed steel Wide flutes Increased wear resistance For extremely deep holes For unsatisfactory chip evacuation
high tensile steels and cast steels grey cast iron malleable and spheroidal iron
Surface Type GT 100 Cutting direction rh Point grinding Relieved cone Point angle 130 Web thinned 3.00 Standard range, page 408
alloyed/unall. steel and cast steel grey cast iron, malleable cast iron spheroidal cast iron sintered powder metal German silver graphite
Surface Type N Cutting direction rh Point grinding Relieved cone Point angle 118 Web thinned 3.50 Standard range, page 412
Wide flutes For extremely deep holes For unsatisfactory chip evacuation
steels and cast iron up to 1000 N/mm Not recommended for: CrNi steels, stainless steels
Surface Type GT 100 Cutting direction rh Point grinding Relieved cone Point angle 130 Web thinned 2.50 Standard range, page 412
AlTiN
TiCN
FIRE
AlCrN
TiN
MolyGlide
155
soft and long chipping materials of 500 N/mm mild steel aluminium, aluminium alloys zinc, refined copper, silumin, electron zamak, argalium, soft synthetic mat. wood
Surface Type GT 50 Cutting direction rh Point grinding Relieved cone Point angle 130 Web thinned 2.50 Standard range, page 412
Wide flutes For extremely deep holes For unsatisfactory chip evacuation
steels and cast iron up to 1000 N/mm Not recommended for: CrNi steels, stainless steels
Surface Type GT 100 Cutting direction rh Point grinding Relieved cone Point angle 130 Web thinned 6.00 Standard range, page 415
Wide flutes For extremely deep holes For unsatisfactory chip evacuation
steels and cast iron up to 1000 N/mm Not recommended for: CrNi steels, stainless steels
Surface Type GT 100 Cutting direction rh Point grinding Relieved cone Point angle 130 Web thinned 8.00 Standard range, page 416
Wide flutes For extremely deep holes For unsatisfactory chip evacuation
steels and cast iron up to 1000 N/mm Not recommended for: CrNi steels, stainless steels
Surface Type GT 100 Cutting direction rh Point grinding Relieved cone Point angle 130 Web thinned 10.00 Standard range, page 417
Surface Type N Cutting direction rh Point grinding Relieved cone Point angle 118 Web thinned 1.50 Standard range, page 418
bright
steam tempered
nitrided lands
nitrided
golden brown
TiAlN
156
Surface Type N Cutting direction rh Point grinding Relieved cone Point angle 135 Web thinned 1.50 Standard range, page 418
Surface Type N Cutting direction rh Point grinding Relieved cone Point angle 118 Web thinned 1.50 Standard range, page 421
Surface Type N Cutting direction rh Point grinding Relieved cone Point angle 135 Web thinned 1.50 Standard range, page 421
Pin drills
With tang For tapered holes For holding taper pins To DIN 1 (new: DIN EN 22 339) and DIN 7978 (new: DIN EN 28 736)
Surface Type N Cutting direction rh Point grinding Relieved cone Point angle 118 Web thinned 1.00 Standard range, page 423
Carbide tipped
spring steel hard cast iron over 300 Brinell pure molybdenum hard bronzes
Surface Type N Cutting direction rh Point grinding Facet point Point angle 118 Web thinned 1.70 Standard range, page 424
AlTiN
TiCN
FIRE
AlCrN
TiN
MolyGlide
157
Carbide tipped
fiberglass reinforced plastics Duroplastics that cause wear on lands and cutting edges
Surface Type N Cutting direction rh Point grinding Facet point Point angle 85 Web thinned 1.50 Standard range, page 424
Kevlar drills
Guhring no. 1149 Standard Guhring std. Tool material Solid carbide
Surface Type N Cutting direction rh Point grinding Special Point angle Web thinned Standard range, page 428
Surface Type Cutting direction rh Point grinding Facet point Point angle 120 Web thinned 3.00 Standard range, page 429
Masonry drills
Carbide tipped For drills and hammer drills Drilling tiles without hammer action!
Surface Type N Cutting direction rh Point grinding Facet point Point angle 120 Web thinned Standard range, page 430
Jobber drills
Surface Type GV 120 Cutting direction rh Point grinding Relieved cone Point angle 130 Web thinned 7.00 Standard range, page 431
bright
steam tempered
nitrided lands
nitrided
golden brown
TiAlN
158
Jobber drills
Surface Type GV 120 Cutting direction rh Point grinding Relieved cone Point angle 130 Web thinned 9.00 Standard range, page 431
Jobber drills
Surface Type VA Cutting direction rh Point grinding Relieved cone Point angle 130 Web thinned Standard range, page 431
Twist drills
Surface Type N Cutting direction rh Point grinding Relieved cone Point angle 118 Web thinned 8.00 Standard range, page 434
Twist drills
Standard drill
alloyed/unall. steel and cast steel grey cast iron, malleable cast iron spheroidal cast iron sintered powder iron German silver, graphite
Surface Type N Cutting direction rh Point grinding Relieved cone Point angle 118 Web thinned 14.01 Standard range, page 434
Twist drills
Standard drill
hard, crumbly materials brass, magnesium alloys bronze, phosphor bronze thin zamac and electron slate, mico, pertinax with special point grind: insulating materials, ebonite, bakelite galalithe, celluloid, synthetic resins horn compounds, eternit, plexiglass
Surface Type H Cutting direction rh Point grinding Relieved cone Point angle 118 Web thinned 14.01 Standard range, page 434
AlTiN
TiCN
FIRE
AlCrN
TiN
MolyGlide
159
Surface Type W Cutting direction rh Point grinding Relieved cone Point angle 130 Web thinned 14.01 Standard range, page 434
Twist drills
Standard drill
alloyed/unall. steel and cast steel grey cast iron, malleable cast iron spheroidal cast iron sintered powder iron German silver, graphite
Surface Type N Cutting direction lh Point grinding Relieved cone Point angle 118 Web thinned 14.01 Standard range, page 434
Twist drills
steels and cast iron up to 1000 N/mm Not recommended for: CrNi steels, stainless steels
Surface Type GT 100 Cutting direction rh Point grinding Relieved cone Point angle 130 Web thinned 7.94 Standard range, page 434
Twist drills
Surface Type N Cutting direction rh Point grinding Relieved cone Point angle 118 Web thinned 10.00 Standard range, page 434
Twist drills
steels and cast iron up to 1000 N/mm Not recommended for: CrNi steels, stainless steels
Surface Type GT 100 Cutting direction rh Point grinding Relieved cone Point angle 130 Web thinned 7.94 Standard range, page 435
bright
steam tempered
nitrided lands
nitrided
golden brown
TiAlN
160
Twist drills
Standard drill
alloyed/unall. steel and cast steel grey cast iron, malleable cast iron spheroidal cast iron sintered powder iron German silver, graphite
Surface Type N Cutting direction rh Point grinding Relieved cone Point angle 118 Web thinned 3.00 Standard range, page 435
Twist drills
alloyed and unalloyed steels and castings over 800 N/mm hot and cold rolled steels antifriction bearing steels high alloyed steels case hardening and heat-treatable steels
Surface Type N Cutting direction rh Point grinding Relieved cone Point angle 118 Web thinned 3.00 Standard range, page 435
Twist drills
Co-alloyed high speed steel Wide flutes Increased wear resistance Especially for drilling depths over 3xD
alloyed and unalloyed steels and castings over 1000 N/mm hot and cold rolled steels antifriction bearing steels high alloyed steels case hardening and heat-treatable steels
Surface Type GT 100 Cutting direction rh Point grinding Relieved cone Point angle 130 Web thinned 9.52 Standard range, page 435
Twist drills
alloyed and unalloyed steels and castings over 800 N/mm hot and cold rolled steels antifriction bearing steels high alloyed steels case hardening and heat-treatable steels
Surface Type N Cutting direction rh Point grinding Relieved cone Point angle 118 Web thinned 7.94 Standard range, page 435
Twist drills
Co-alloyed high speed steel Wide flutes Increased wear resistance Especially for drilling depths over 3xD
alloyed and unalloyed steels and castings over 1000 N/mm hot and cold rolled steels antifriction bearing steels high alloyed steels case hardening and heat-treatable steels
Surface Type GT 100 Cutting direction rh Point grinding Relieved cone Point angle 130 Web thinned 10.00 Standard range, page 435
AlTiN
TiCN
FIRE
AlCrN
TiN
MolyGlide
161
Surface Type GT 100 Cutting direction rh Point grinding Relieved cone Point angle 130 Web thinned 10.00 Standard range, page 435
Twist drills
Co-alloyed high speed steel Wide flutes Increased wear resistance Especially for drilling depths over 3xD
alloyed and unalloyed steels and castings over 1000 N/mm hot and cold rolled steels antifriction bearing steels high alloyed steels case hardening and heat-treatable steels
Surface Type GT 100 Cutting direction rh Point grinding Relieved cone Point angle 130 Web thinned 10.00 Standard range, page 435
Twist drills
Surface Type VA Cutting direction rh Point grinding Relieved cone Point angle 130 Web thinned Standard range, page 435
Twist drills
alloyed/unall. steel and cast steel grey cast iron, malleable cast iron spheroidal cast iron sintered powder iron German silver, graphite
Surface Type N Cutting direction rh Point grinding Relieved cone Point angle 118 Web thinned 14.01 Standard range, page 460
Twist drills
alloyed and unalloyed steels and castings over 1000 N/mm hot and cold rolled steels antifriction bearing steels high alloyed steels case hardening and heat-treatable steels
Surface Type N Cutting direction rh Point grinding Relieved cone Point angle 118 Web thinned 10.00 Standard range, page 460
bright
steam tempered
nitrided lands
nitrided
golden brown
TiAlN
162
alloyed/unall. steel and cast steel grey cast iron, malleable cast iron spheroidal cast iron sintered powder iron German silver, graphite
Surface Type N Cutting direction rh Point grinding Relieved cone Point angle 118 Web thinned 14.01 Standard range, page 462
soft and long chipping materials of 500 N/mm mild steel aluminium, aluminium alloys zinc, refined copper, silumin, electron zamak, argalium, soft synthetic mat. wood
Surface Type GT 50 Cutting direction rh Point grinding Relieved cone Point angle 130 Web thinned 4.20 Standard range, page 462
steels and cast iron up to 1000 N/mm Not recommended for: CrNi steels, stainless steels
Surface Type GT 100 Cutting direction rh Point grinding Relieved cone Point angle 130 Web thinned 5.50 Standard range, page 462
alloyed/unall. steel and cast steel grey cast iron, malleable cast iron spheroidal cast iron sintered powder iron German silver, graphite
Surface Type N Cutting direction rh Point grinding Relieved cone Point angle 118 Web thinned 4.00 Standard range, page 462
steels and cast iron up to 1000 N/mm Not recommended for: CrNi steels, stainless steels
Surface Type GT 100 Cutting direction rh Point grinding Relieved cone Point angle 130 Web thinned 5.60 Standard range, page 462
AlTiN
TiCN
FIRE
AlCrN
TiN
MolyGlide
163
Surface Type N Cutting direction rh Point grinding Relieved cone Point angle 118 Web thinned 4.75 Standard range, page 462
Co-alloyed high speed steel Wide flutes Increased wear resistance For unsatisfactory chip evacuation
alloyed and unalloyed steels and castings over 800 N/mm hot and cold rolled steels antifriction bearing steels high alloyed steels case hardening and heat-treatable steels
Surface Type GT 100 Cutting direction rh Point grinding Relieved cone Point angle 130 Web thinned 10.00 Standard range, page 462
Special geometry With oversize taper For drilling through drill bushes
alloyed/unall. steel and cast steel grey cast iron, malleable cast iron spheroidal cast iron sintered powder iron German silver, graphite
Surface Type N Cutting direction rh Point grinding Relieved cone Point angle 118 Web thinned 14.01 Standard range, page 469
laminated sheet metal steel, cast iron, grey cast iron austenitic steels up to 800 N/mm
Surface Type N Cutting direction rh Point grinding Relieved cone Point angle 118 Web thinned 9.52 Standard range, page 470
laminated sheet metal steel, cast iron, grey cast iron austenitic steels up to 800 N/mm
Surface Type N Cutting direction rh Point grinding Relieved cone Point angle 118 Web thinned 10.00 Standard range, page 472
bright
steam tempered
nitrided lands
nitrided
golden brown
TiAlN
164
laminated sheet metal steel, cast iron, grey cast iron austenitic steels up to 800 N/mm
Surface Type N Cutting direction rh Point grinding Relieved cone Point angle 118 Web thinned 10.00 Standard range, page 473
laminated sheet metal steel, cast iron, grey cast iron austenitic steels up to 800 N/mm
Surface Type N Cutting direction rh Point grinding Relieved cone Point angle 118 Web thinned 10.00 Standard range, page 473
laminated sheet metal steel, cast iron, grey cast iron austenitic steels up to 800 N/mm
Surface Type N Cutting direction rh Point grinding Relieved cone Point angle 118 Web thinned 10.00 Standard range, page 473
Co-alloyed high speed steel Increased wear resistance For drilling through drill bushes
tensile and high tensile steels cast steel, grey cast iron stainless/acid-/heat-resistant steels above 800 up to 1300 N/mm
Surface Type GT 100 Cutting direction rh Point grinding Relieved cone Point angle 130 Web thinned 11.00 Standard range, page 473
Co-alloyed high speed steel Increased wear resistance For drilling through drill bushes
tensile and high tensile steels cast steel, grey cast iron stainless/acid-/heat-resistant steels above 800 up to 1300 N/mm
Surface Type GT 100 Cutting direction rh Point grinding Relieved cone Point angle 130 Web thinned 11.00 Standard range, page 473
AlTiN
TiCN
FIRE
AlCrN
TiN
MolyGlide
165
Surface Type GT 100 Cutting direction rh Point grinding Relieved cone Point angle 130 Web thinned 11.00 Standard range, page 473
Co-alloyed high speed steel Increased wear resistance For drilling through drill bushes
tensile and high tensile steels cast steel, grey cast iron stainless/acid-/heat-resistant steels above 800 up to 1300 N/mm
Surface Type GT 100 Cutting direction rh Point grinding Relieved cone Point angle 130 Web thinned 11.00 Standard range, page 476
Co-alloyed high speed steel Increased wear resistance For drilling through drill bushes
tensile and high tensile steels cast steel, grey cast iron stainless/acid-/heat-resistant steels above 800 up to 1300 N/mm
Surface Type GT 100 Cutting direction rh Point grinding Relieved cone Point angle 130 Web thinned 11.00 Standard range, page 476
Co-alloyed high speed steel Increased wear resistance For drilling through drill bushes
tensile and high tensile steels cast steel, grey cast iron stainless/acid-/heat-resistant steels above 800 up to 1300 N/mm
Surface Type GT 100 Cutting direction rh Point grinding Relieved cone Point angle 130 Web thinned 11.00 Standard range, page 476
alloyed/unall. steel and cast steel grey cast iron, malleable cast iron spheroidal cast iron sintered powder metal German silver graphite
Surface Type N Cutting direction rh Point grinding Relieved cone Point angle 118 Web thinned 7.55 Standard range, page 478
bright
steam tempered
nitrided lands
nitrided
golden brown
TiAlN
166
soft and long chipping materials of 500 N/mm mild steel aluminium, aluminium alloys zinc, refined copper, silumin, electron zamak, argalium, soft synthetic mat. wood
Surface Type GT 50 Cutting direction rh Point grinding Relieved cone Point angle 130 Web thinned 7.75 Standard range, page 478
Wide flutes For unsatisfactory chip evacuation For extremely deep holes
steels and cast iron up to 1000 N/mm Not recommended for: CrNi steels, stainless steels
Surface Type GT 100 Cutting direction rh Point grinding Relieved cone Point angle 130 Web thinned 5.80 Standard range, page 478
Co-alloyed high speed steel Wide flutes Increased wear resistance For unsatisfactory chip evacuation For extremely deep holes
high tensile steels and cast steels grey cast iron malleable and spheroidal iron
Surface Type GT 100 Cutting direction rh Point grinding Relieved cone Point angle 130 Web thinned 9.52 Standard range, page 478
alloyed/unall. steel and cast steel grey cast iron, malleable cast iron spheroidal cast iron sintered powder metal German silver graphite
Surface Type N Cutting direction rh Point grinding Relieved cone Point angle 118 Web thinned 7.70 Standard range, page 482
Wide flutes For unsatisfactory chip evacuation For extremely deep holes
steels and cast iron up to 1000 N/mm Not recommended for: CrNi steels, stainless steels
Surface Type GT 100 Cutting direction rh Point grinding Relieved cone Point angle 130 Web thinned 7.50 Standard range, page 482
AlTiN
TiCN
FIRE
AlCrN
TiN
MolyGlide
167
Surface Type GT 50 Cutting direction rh Point grinding Relieved cone Point angle 130 Web thinned 8.00 Standard range, page 482
Co-alloyed high speed steel Wide flutes Increased wear resistance For unsatisfactory chip evacuation For extremely deep holes
high tensile steels and cast steels grey cast iron malleable and spheroidal iron
Surface Type GT 100 Cutting direction rh Point grinding Relieved cone Point angle 130 Web thinned 9.52 Standard range, page 482
Wide flutes For unsatisfactory chip evacuation For extremely deep holes
steels and cast iron up to 1000 N/mm Not recommended for: CrNi steels, stainless steels
Surface Type GT 100 Cutting direction rh Point grinding Relieved cone Point angle 130 Web thinned 6.00 Standard range, page 485
Wide flutes For unsatisfactory chip evacuation For extremely deep holes
steels and cast iron up to 1000 N/mm Not recommended for: CrNi steels, stainless steels
Surface Type GT 100 Cutting direction rh Point grinding Relieved cone Point angle 130 Web thinned 8.00 Standard range, page 485
Wide flutes For unsatisfactory chip evacuation For extremely deep holes
steels and cast iron up to 1000 N/mm Not recommended for: CrNi steels, stainless steels
Surface Type GT 100 Cutting direction rh Point grinding Relieved cone Point angle 130 Web thinned 14.01 Standard range, page 486
bright
steam tempered
nitrided lands
nitrided
golden brown
TiAlN
168
Wide flutes For unsatisfactory chip evacuation For extremely deep holes
steels and cast iron up to 1000 N/mm Not recommended for: CrNi steels, stainless steels
Surface Type GT 100 Cutting direction rh Point grinding Relieved cone Point angle 130 Web thinned 6.00 Standard range, page 486
Wide flutes For unsatisfactory chip evacuation For extremely deep holes
steels and cast iron up to 1000 N/mm Not recommended for: CrNi steels, stainless steels
Surface Type GT 100 Cutting direction rh Point grinding Relieved cone Point angle 130 Web thinned 6.00 Standard range, page 487
Wide flutes For unsatisfactory chip evacuation For extremely deep holes
steels and cast iron up to 1000 N/mm Not recommended for: CrNi steels, stainless steels
Surface Type GT 100 Cutting direction rh Point grinding Relieved cone Point angle 130 Web thinned 14.01 Standard range, page 488
Wide flutes For unsatisfactory chip evacuation For extremely deep holes
steels and cast iron up to 1000 N/mm Not recommended for: CrNi steels, stainless steels
Surface Type GT 100 Cutting direction rh Point grinding Relieved cone Point angle 130 Web thinned 14.01 Standard range, page 489
Pin drills
For tapered holes For holding taper pins To DIN 1 (new: DIN EN 22 339), DIN 7978 (new: DIN EN 28 736), DIN 7977 (new: DIN EN 28737) and DIN 258
Surface Type N Cutting direction rh Point grinding Relieved cone Point angle 118 Web thinned 5.00 Standard range, page 490
AlTiN
TiCN
FIRE
AlCrN
TiN
MolyGlide
169
Surface Type N Cutting direction rh Point grinding Relieved cone Point angle 118 Web thinned 8.00 Standard range, page 491
Guhring no. 1659 Standard DIN 6537 K Tool material Solid carbide
Concave cutting edge geometry Special web thinning Special point grind Very good self-centering characteristics Highest cutting rates (see Guroguide) Short chips Close diameter tolerances Alignment accurate holes Powerful machines Max. conc. error of clamped tool 0.02 mm Play-free spindles
high-alloyed steels stainless/acid-/heat-resistant steels Inconel, Hastelloy, Monel brass, bronze aluminium and aluminium alloys magnesium and magnesium alloys titanium and titanium alloys sintered powder metals
Surface Type RT 100 F Cutting direction rh Point grinding Relieved cone Point angle 140 Web thinned 3.70 Standard range, page 494 Guhring no. 2475 Standard DIN 6537 K Tool material Solid carbide
Concave cutting edge geometry Special web thinning Special point grind Very good self-centering characteristics Highest cutting rates (see Guroguide) Short chips Close diameter tolerances Alignment accurate holes Powerful machines Max. conc. error of clamped tool 0.02 mm Play-free spindles
high-alloyed steels stainless/acid-/heat-resistant steels Inconel, Hastelloy, Monel brass, bronze aluminium and aluminium alloys magnesium and magnesium alloys titanium and titanium alloys sintered powder metals
Surface Type RT 100 F Cutting direction rh Point grinding Relieved cone Point angle 140 Web thinned 3.70 Standard range, page 494 Guhring no. 1184 Standard DIN 6537 K Tool material Solid carbide
Concave cutting edge geometry Special web thinning Special point grind Very good self-centering characteristics Highest cutting rates (see Guroguide) Short chips Alignment accurate holes Powerful machines Chatter-free, defined feed Max. conc. error of clamped tool 0.02 mm Play-free spindles
structural and case hardened steels cast steels, heat-treatable steels alloyed steels up to 1200 N/mm carbon steels, bronze, cast iron high alloyed AlSi alloys
Surface Type RT 100 U Cutting direction rh Point grinding Relieved cone Point angle 140 Web thinned 3.00 Standard range, page 494 Guhring no. 1673 Standard DIN 6537 K Tool material Solid carbide
Concave cutting edge geometry Special web thinning Special point grind Very good self-centering characteristics Highest cutting rates (see Guroguide) Short chips Alignment accurate holes Powerful machines Chatter-free, defined feed Max. conc. error of clamped tool 0.02 mm Play-free spindles
structural and case hardened steels cast steels, heat-treatable steels alloyed steels up to 1200 N/mm carbon steels, bronze, cast iron high alloyed AlSi alloys
Surface Type RT 100 U Cutting direction rh Point grinding Relieved cone Point angle 140 Web thinned 3.00 Standard range, page 494
bright
steam tempered
nitrided lands
nitrided
golden brown
TiAlN
170
Ratio drills
Ratio drills without oil feed Guhring no. 2472 Standard DIN 6537 K Tool material Solid carbide
Concave cutting edge geometry Special web thinning Special point grind Very good self-centering characteristics Highest cutting rates (see Guroguide) Short chips Alignment accurate holes Powerful machines Chatter-free, defined feed Max. conc. error of clamped tool 0.02 mm Play-free spindles structural and case hardened steels cast steels, heat-treatable steels alloyed steels up to 1200 N/mm carbon steels, bronze, cast iron high alloyed AlSi alloys Ratio drills
Surface Type RT 100 U Cutting direction rh Point grinding Relieved cone Point angle 140 Web thinned 3.00 Standard range, page 494 Guhring no. 2480 Standard DIN 6537 K Tool material Solid carbide
Concave cutting edge geometry Special web thinning Special point grind Very good self-centering characteristics Highest cutting rates (see Guroguide) Short chips Alignment accurate holes Powerful machines Chatter-free, defined feed Max. conc. error of clamped tool 0.02 mm Play-free spindles
structural and case hardened steels cast steels, heat-treatable steels alloyed steels up to 1200 N/mm carbon steels, bronze, cast iron high alloyed AlSi alloys
Surface Type RT 100 U Cutting direction rh Point grinding Relieved cone Point angle 140 Web thinned 3.00 Standard range, page 494 Guhring no. 2712 Standard DIN 6537 L Tool material Solid carbide
Concave cutting edge geometry Special web thinning Special point grind Very good self-centering characteristics Highest cutting rates (see Guroguide) Short chips Close diameter tolerances Alignment accurate holes Powerful machines Max. conc. error of clamped tool 0.02 mm Play-free spindles
high-alloyed steels stainless/acid-/heat-resistant steels Inconel, Hastelloy, Monel brass, bronze aluminium and aluminium alloys magnesium and magnesium alloys titanium and titanium alloys sintered powder metals
Surface Type RT 100 F Cutting direction rh Point grinding Relieved cone Point angle 140 Web thinned 3.00 Standard range, page 499 Guhring no. 2717 Standard DIN 6537 L Tool material Solid carbide
Concave cutting edge geometry Special web thinning Special point grind Very good self-centering characteristics Highest cutting rates (see Guroguide) Short chips Alignment accurate holes Powerful machines Chatter-free, defined feed Max. conc. error of clamped tool 0.02 mm Play-free spindles
structural and case hardened steels cast steels, heat-treatable steels alloyed steels up to 1200 N/mm carbon steels, bronze, cast iron high alloyed AlSi alloys
Surface Type RT 100 U Cutting direction rh Point grinding Relieved cone Point angle 140 Web thinned 3.00 Standard range, page 499 Guhring no. 2718 Standard DIN 6537 L Tool material Solid carbide
Concave cutting edge geometry Special web thinning Special point grind Very good self-centering characteristics Highest cutting rates (see Guroguide) Short chips Alignment accurate holes Powerful machines Chatter-free, defined feed Max. conc. error of clamped tool 0.02 mm Play-free spindles
structural and case hardened steels cast steels, heat-treatable steels alloyed steels up to 1200 N/mm carbon steels, bronze, cast iron high alloyed AlSi alloys
Surface Type RT 100 U Cutting direction rh Point grinding Relieved cone Point angle 140 Web thinned 3.00 Standard range, page 499
AlTiN
TiCN
FIRE
AlCrN
TiN
MolyGlide
171
Ratio drills
Ratio drills without oil feed
Ratio drills
Guhring no. 2719 Standard DIN 6537 L Tool material Solid carbide
Concave cutting edge geometry Special web thinning Special point grind Very good self-centering characteristics Highest cutting rates (see Guroguide) Short chips Alignment accurate holes Powerful machines Chatter-free, defined feed Max. conc. error of clamped tool 0.02 mm Play-free spindles
structural and case hardened steels cast steels, heat-treatable steels alloyed steels up to 1200 N/mm carbon steels, bronze, cast iron high alloyed AlSi alloys
Surface Type RT 100 U Cutting direction rh Point grinding Relieved cone Point angle 140 Web thinned 3.00 Standard range, page 499 Guhring no. 2996 Standard DIN 6537 L Tool material Solid carbide
Concave cutting edge geometry Special web thinning Special point grind Very good self-centering characteristics Highest cutting rates (see Guroguide) Short chips Alignment accurate holes Powerful machines Chatter-free, defined feed Max. conc. error of clamped tool 0.02 mm Play-free spindles
structural and case hardened steels cast steels, heat-treatable steels alloyed steels up to 1200 N/mm carbon steels, bronze, cast iron high alloyed AlSi alloys
Surface Type RT 100 U Cutting direction rh Point grinding Relieved cone Point angle 140 Web thinned 3.00 Standard range, page 499 Guhring no. 1702 Standard DIN 6539 Tool material Solid carbide
Concave cutting edge geometry Special web thinning Special point grind Very good self-centering characteristics Highest cutting rates (see Guroguide) Short chips Alignment accurate holes Powerful machines Chatter-free, defined feed Max. conc. error of clamped tool 0.02 mm Play-free spindles
high-alloyed steels stainless/acid-/heat-resistant steels Inconel, Hastelloy, Monel brass, bronze aluminium and aluminium alloys magnesium and magnesium alloys titanium and titanium alloys sintered powder metals
Surface Type RT 100 F Cutting direction rh Point grinding Relieved cone Point angle 140 Web thinned 3.00 Standard range, page 503 Guhring no. 1798 Standard DIN 6539 Tool material Solid carbide
Concave cutting edge geometry Special web thinning Special point grind Very good self-centering characteristics Highest cutting rates (see Guroguide) Short chips Alignment accurate holes Powerful machines Chatter-free, defined feed Max. conc. error of clamped tool 0.02 mm Play-free spindles
cast iron, grey cast iron malleable cast iron spheroidal graphite iron aluminium alloys with high Si-content abrasive materials
Surface Type RT 100 G Cutting direction rh Point grinding Relieved cone Point angle 140 Web thinned 3.00 Standard range, page 503 Guhring no. 1242 Standard DIN 6539 Tool material Solid carbide
Concave cutting edge geometry Special web thinning Special point grind Very good self-centering characteristics Highest cutting rates (see Guroguide) Short chips Alignment accurate holes Powerful machines Chatter-free, defined feed Max. conc. error of clamped tool 0.02 mm Play-free spindles
structural and case hardened steels cast steels, heat-treatable steels alloyed steels up to 1200 N/mm carbon steels, bronze, cast iron high alloyed AlSi alloys
Surface Type RT 100 U Cutting direction rh Point grinding Relieved cone Point angle 140 Web thinned 3.00 Standard range, page 503
bright
steam tempered
nitrided lands
nitrided
golden brown
TiAlN
172
Ratio drills
Ratio drills without oil feed Guhring no. 2473 Standard DIN 6539 Tool material Solid carbide
Concave cutting edge geometry Special web thinning Special point grind Very good self-centering characteristics Highest cutting rates (see Guroguide) Short chips Alignment accurate holes Powerful machines Chatter-free, defined feed Max. conc. error of clamped tool 0.02 mm Play-free spindles structural and case hardened steels cast steels, heat-treatable steels alloyed steels up to 1200 N/mm carbon steels, bronze, cast iron high alloyed AlSi alloys Ratio drills
Surface Type RT 100 U Cutting direction rh Point grinding Relieved cone Point angle 140 Web thinned 3.00 Standard range, page 503 Guhring no. 1799 Standard Guhring std. Tool material Solid carbide
Concave cutting edge geometry Special web thinning Special point grind Very good self-centering characteristics Highest cutting rates (see Guroguide) Short chips Alignment accurate holes Powerful machines Chatter-free, defined feed Max. conc. error of clamped tool 0.02 mm Play-free spindles
cast iron, grey cast iron malleable cast iron spheroidal graphite iron aluminium alloys with high Si-content abrasive materials
Surface Type RT 100 G Cutting direction rh Point grinding Relieved cone Point angle 140 Web thinned 5.00 Standard range, page 507 Guhring no. 1243 Standard Guhring std. Tool material Solid carbide
Concave cutting edge geometry Special web thinning Special point grind Very good self-centering characteristics Highest cutting rates (see Guroguide) Short chips Alignment accurate holes Powerful machines Chatter-free, defined feed Max. conc. error of clamped tool 0.02 mm Play-free spindles
structural and case hardened steels cast steels, heat-treatable steels alloyed steels up to 1200 N/mm carbon steels, bronze, cast iron high alloyed AlSi alloys
Surface Type RT 100 U Cutting direction rh Point grinding Relieved cone Point angle 140 Web thinned 5.00 Standard range, page 507 Guhring no. 2474 Standard Guhring std. Tool material Solid carbide
Concave cutting edge geometry Special web thinning Special point grind Very good self-centering characteristics Highest cutting rates (see Guroguide) Short chips Alignment accurate holes Powerful machines Chatter-free, defined feed Max. conc. error of clamped tool 0.02 mm Play-free spindles
structural and case hardened steels cast steels, heat-treatable steels alloyed steels up to 1200 N/mm carbon steels, bronze, cast iron high alloyed AlSi alloys
Surface Type RT 100 U Cutting direction rh Point grinding Relieved cone Point angle 140 Web thinned 5.00 Standard range, page 507 Guhring no. 1180 Standard DIN 6537 K Tool material Solid carbide
Concave cutting edge geometry Special web thinning Special point grind Straight shank without flat Highest cutting rates (see Guroguide) Short chips Alignment accurate holes Application in hydraulic chucks Powerful machines Max. conc. error of clamped tool 0.02 mm Play-free spindles
high-alloyed steels stainless/acid-/heat-resistant steels Inconel, Hastelloy, Monel brass, bronze aluminium and aluminium alloys magnesium and magnesium alloys titanium and titanium alloys sintered powder metals
Surface Type RT 100 F Cutting direction rh Point grinding Relieved cone Point angle 140 Web thinned 3.00 Standard range, page 510
AlTiN
TiCN
FIRE
AlCrN
TiN
MolyGlide
173
Ratio drills
Ratio drills with oil feed
Ratio drills
Guhring no. 1660 Standard DIN 6537 K Tool material Solid carbide
Concave cutting edge geometry Special web thinning Special point grind Straight shank without flat Highest cutting rates (see Guroguide) Short chips Alignment accurate holes Application in hydraulic chucks Powerful machines Max. conc. error of clamped tool 0.02 mm Play-free spindles
high-alloyed steels stainless/acid-/heat-resistant steels Inconel, Hastelloy, Monel brass, bronze aluminium and aluminium alloys magnesium and magnesium alloys titanium and titanium alloys sintered powder metals
Surface Type RT 100 F Cutting direction rh Point grinding Relieved cone Point angle 140 Web thinned 3.00 Standard range, page 510 Guhring no. 2468 Standard DIN 6537 K Tool material Solid carbide
Concave cutting edge geometry Special web thinning Special point grind Straight shank without flat Highest cutting rates (see Guroguide) Short chips Alignment accurate holes Application in hydraulic chucks Powerful machines Max. conc. error of clamped tool 0.02 mm Play-free spindles
high-alloyed steels stainless/acid-/heat-resistant steels Inconel, Hastelloy, Monel brass, bronze aluminium and aluminium alloys magnesium and magnesium alloys titanium and titanium alloys sintered powder metals
Surface Type RT 100 F Cutting direction rh Point grinding Relieved cone Point angle 140 Web thinned 3.00 Standard range, page 511 Guhring no. 1181 Standard DIN 6537 K Tool material Solid carbide
Concave cutting edge geometry Special web thinning Special point grind Straight shank without flat Highest cutting rates (see Guroguide) Short chips Alignment accurate holes Application in hydraulic chucks Powerful machines Max. conc. error of clamped tool 0.02 mm Play-free spindles
structural and case hardened steels cast steels, heat-treatable steels alloyed steels up to 1200 N/mm carbon steels, bronze, cast iron high alloyed AlSi alloys
Surface Type RT 100 U Cutting direction rh Point grinding Relieved cone Point angle 140 Web thinned 3.00 Standard range, page 511 Guhring no. 1661 Standard DIN 6537 K Tool material Solid carbide
Concave cutting edge geometry Special web thinning Special point grind Straight shank without flat Highest cutting rates (see Guroguide) Short chips Alignment accurate holes Application in hydraulic chucks Powerful machines Max. conc. error of clamped tool 0.02 mm Play-free spindles
structural and case hardened steels cast steels, heat-treatable steels alloyed steels up to 1200 N/mm carbon steels, bronze, cast iron high alloyed AlSi alloys
Surface Type RT 100 U Cutting direction rh Point grinding Relieved cone Point angle 140 Web thinned 3.00 Standard range, page 511 Guhring no. 2469 Standard DIN 6537 K Tool material Solid carbide
Concave cutting edge geometry Special web thinning Special point grind Straight shank without flat Highest cutting rates (see Guroguide) Short chips Alignment accurate holes Application in hydraulic chucks Powerful machines Max. conc. error of clamped tool 0.02 mm Play-free spindles
structural and case hardened steels cast steels, heat-treatable steels alloyed steels up to 1200 N/mm carbon steels, bronze, cast iron high alloyed AlSi alloys
Surface Type RT 100 U Cutting direction rh Point grinding Relieved cone Point angle 140 Web thinned 3.00 Standard range, page 511
bright
steam tempered
nitrided lands
nitrided
golden brown
TiAlN
174
Ratio drills
Ratio drills with oil feed Guhring no. 2477 Standard DIN 6537 K Tool material Solid carbide
Concave cutting edge geometry Special web thinning Special point grind Straight shank without flat Highest cutting rates (see Guroguide) Short chips Alignment accurate holes Application in hydraulic chucks Powerful machines Max. conc. error of clamped tool 0.02 mm Play-free spindles structural and case hardened steels cast steels, heat-treatable steels alloyed steels up to 1200 N/mm carbon steels, bronze, cast iron high alloyed AlSi alloys Ratio drills
Surface Type RT 100 U Cutting direction rh Point grinding Relieved cone Point angle 140 Web thinned 3.00 Standard range, page 511 Guhring no. 1182 Standard DIN 6537 L Tool material Solid carbide
Concave cutting edge geometry Special web thinning Special point grind Straight shank without flat Highest cutting rates (see Guroguide) Short chips Alignment accurate holes Application in hydraulic chucks Powerful machines Max. conc. error of clamped tool 0.02 mm Play-free spindles
high-alloyed steels stainless/acid-/heat-resistant steels Inconel, Hastelloy, Monel brass, bronze aluminium and aluminium alloys magnesium and magnesium alloys titanium and titanium alloys sintered powder metals
Surface Type RT 100 F Cutting direction rh Point grinding Relieved cone Point angle 140 Web thinned 3.00 Standard range, page 520 Guhring no. 1662 Standard DIN 6537 L Tool material Solid carbide
Concave cutting edge geometry Special web thinning Special point grind Straight shank without flat Highest cutting rates (see Guroguide) Short chips Alignment accurate holes Application in hydraulic chucks Powerful machines Max. conc. error of clamped tool 0.02 mm Play-free spindles
high-alloyed steels stainless/acid-/heat-resistant steels Inconel, Hastelloy, Monel brass, bronze aluminium and aluminium alloys magnesium and magnesium alloys titanium and titanium alloys sintered powder metals
Surface Type RT 100 F Cutting direction rh Point grinding Relieved cone Point angle 140 Web thinned 3.00 Standard range, page 520 Guhring no. 2470 Standard DIN 6537 L Tool material Solid carbide
Concave cutting edge geometry Special web thinning Special point grind Straight shank without flat Highest cutting rates (see Guroguide) Short chips Alignment accurate holes Application in hydraulic chucks Powerful machines Max. conc. error of clamped tool 0.02 mm Play-free spindles
high-alloyed steels stainless/acid-/heat-resistant steels Inconel, Hastelloy, Monel brass, bronze aluminium and aluminium alloys magnesium and magnesium alloys titanium and titanium alloys sintered powder metals
Surface Type RT 100 F Cutting direction rh Point grinding Relieved cone Point angle 140 Web thinned 3.00 Standard range, page 520 Guhring no. 2478 Standard DIN 6537 L Tool material Solid carbide
Concave cutting edge geometry Special web thinning Special point grind Straight shank without flat Highest cutting rates (see Guroguide) Short chips Alignment accurate holes Application in hydraulic chucks Powerful machines Max. conc. error of clamped tool 0.02 mm Play-free spindles
high-alloyed steels stainless/acid-/heat-resistant steels Inconel, Hastelloy, Monel brass, bronze aluminium and aluminium alloys magnesium and magnesium alloys titanium and titanium alloys sintered powder metals
Surface Type RT 100 F Cutting direction rh Point grinding Relieved cone Point angle 140 Web thinned 3.00 Standard range, page 521
AlTiN
TiCN
FIRE
AlCrN
TiN
MolyGlide
175
Ratio drills
Ratio drills with oil feed
Ratio drills
Guhring no. 6501 Standard DIN 6537 L Tool material Solid carbide
Special geometry Radius point grind Especially high rigidity Maximum tool life High process reliability
CGI and ADI cast materials grey cast iron, spheroidal graphite and malleable cast iron
Surface Type RT 100 R Cutting direction rh Point grinding Relieved cone Point angle Web thinned 3.00 Standard range, page 521
Guhring no. 1183 Standard DIN 6537 L Tool material Solid carbide
Concave cutting edge geometry Special web thinning Special point grind Straight shank without flat Highest cutting rates (see Guroguide) Short chips Alignment accurate holes Application in hydraulic chucks Powerful machines Max. conc. error of clamped tool 0.02 mm Play-free spindles
structural and case hardened steels cast steels, heat-treatable steels alloyed steels up to 1200 N/mm carbon steels, bronze, cast iron high alloyed AlSi alloys
Surface Type RT 100 U Cutting direction rh Point grinding Relieved cone Point angle 140 Web thinned 3.00 Standard range, page 521 Guhring no. 1663 Standard DIN 6537 L Tool material Solid carbide
Concave cutting edge geometry Special web thinning Special point grind Straight shank without flat Highest cutting rates (see Guroguide) Short chips Alignment accurate holes Application in hydraulic chucks Powerful machines Max. conc. error of clamped tool 0.02 mm Play-free spindles
structural and case hardened steels cast steels, heat-treatable steels alloyed steels up to 1200 N/mm carbon steels, bronze, cast iron high alloyed AlSi alloys
Surface Type RT 100 U Cutting direction rh Point grinding Relieved cone Point angle 140 Web thinned 3.00 Standard range, page 521 Guhring no. 2471 Standard DIN 6537 L Tool material Solid carbide
Concave cutting edge geometry Special web thinning Special point grind Straight shank without flat Highest cutting rates (see Guroguide) Short chips Alignment accurate holes Application in hydraulic chucks Powerful machines Max. conc. error of clamped tool 0.02 mm Play-free spindles
structural and case hardened steels cast steels, heat-treatable steels alloyed steels up to 1200 N/mm carbon steels, bronze, cast iron high alloyed AlSi alloys
Surface Type RT 100 U Cutting direction rh Point grinding Relieved cone Point angle 140 Web thinned 3.00 Standard range, page 521 Guhring no. 2479 Standard DIN 6537 L Tool material Solid carbide
Concave cutting edge geometry Special web thinning Special point grind Straight shank without flat Highest cutting rates (see Guroguide) Short chips Alignment accurate holes Application in hydraulic chucks Powerful machines Max. conc. error of clamped tool 0.02 mm Play-free spindles
structural and case hardened steels cast steels, heat-treatable steels alloyed steels up to 1200 N/mm carbon steels, bronze, cast iron high alloyed AlSi alloys
Surface Type RT 100 U Cutting direction rh Point grinding Relieved cone Point angle 140 Web thinned 3.00 Standard range, page 521
bright
steam tempered
nitrided lands
nitrided
golden brown
TiAlN
176
Ratio drills
Ratio drills with oil feed Guhring no. 6502 Standard Guhring std. Tool material Solid carbide
Special geometry Radius point grind Especially high rigidity Maximum tool life High process reliability CGI and ADI cast materials grey cast iron, spheroidal graphite and malleable cast iron Ratio drills
Surface Type RT 100 R Cutting direction rh Point grinding Relieved cone Point angle Web thinned 4.00 Standard range, page 530
Guhring no. 2711 Standard Guhring std. Tool material Solid carbide
Concave cutting edge geometry Special web thinning Special point grind Straight shank without flat Highest cutting rates (see Guroguide) Short chips Alignment accurate holes Application in hydraulic chucks Powerful machines Max. conc. error of clamped tool 0.02 mm Play-free spindles
structural and case hardened steels cast steels, heat-treatable steels alloyed steels up to 1200 N/mm carbon steels, bronze, cast iron high alloyed AlSi alloys
Surface Type RT 100 U Cutting direction rh Point grinding Relieved cone Point angle 140 Web thinned 4.00 Standard range, page 530 Guhring no. 4044 Standard Guhring std. Tool material Solid carbide
Concave cutting edge geometry Special web thinning Special point grind Straight shank without flat Highest cutting rates (see Guroguide) Short chips Alignment accurate holes Application in hydraulic chucks Powerful machines Max. conc. error of clamped tool 0.02 mm Play-free spindles
structural and case hardened steels cast steels, heat-treatable steels alloyed steels up to 1200 N/mm carbon steels, bronze, cast iron high alloyed AlSi alloys
Surface Type RT 100 U Cutting direction rh Point grinding Relieved cone Point angle 140 Web thinned 4.00 Standard range, page 530 Guhring no. 4045 Standard Guhring std. Tool material Solid carbide
Concave cutting edge geometry Special web thinning Special point grind Straight shank without flat Highest cutting rates (see Guroguide) Short chips Alignment accurate holes Application in hydraulic chucks Powerful machines Max. conc. error of clamped tool 0.02 mm Play-free spindles
structural and case hardened steels cast steels, heat-treatable steels alloyed steels up to 1200 N/mm carbon steels, bronze, cast iron high alloyed AlSi alloys
Surface Type RT 100 U Cutting direction rh Point grinding Relieved cone Point angle 140 Web thinned 4.00 Standard range, page 530 Guhring no. 768 Standard Guhring std. Tool material Solid carbide
Very good self-centering characteristics High productivity High cutting rates Close diameter tolerances Very good surface quality of hole Application in hydraulic chucks Alignment accurate tool holders Powerful machines Observe optimal coolant pressure Max. conc. error of clamped tool 0.02 mm Play-free spindles
Surface Type RT 150 GG Cutting direction rh Point grinding Relieved cone Point angle 120 Web thinned 3.00 Standard range, page 535
AlTiN
TiCN
FIRE
AlCrN
TiN
MolyGlide
177
Ratio drills
Ratio drills with oil feed
Ratio drills
Guhring no. 6068 Standard Guhring std. Tool material Solid carbide
Very good self-centering characteristics High productivity High cutting rates Close diameter tolerances Very good surface quality of hole Application in hydraulic chucks Alignment accurate tool holders Powerful machines Observe optimal coolant pressure Max. conc. error of clamped tool 0.02 mm Play-free spindles
Surface Type RT 150 GG Cutting direction rh Point grinding Facet point Point angle 130 Web thinned 3.00 Standard range, page 535 Guhring no. 769 Standard Guhring std. Tool material Solid carbide
Very good self-centering characteristics High productivity High cutting rates Close diameter tolerances Very good surface quality of hole Application in hydraulic chucks Alignment accurate tool holders Powerful machines Observe optimal coolant pressure Max. conc. error of clamped tool 0.02 mm Play-free spindles
Surface Type RT 150 GG Cutting direction rh Point grinding Relieved cone Point angle 120 Web thinned 3.00 Standard range, page 538 Guhring no. 6069 Standard Guhring std. Tool material Solid carbide
Very good self-centering characteristics High productivity High cutting rates Close diameter tolerances Very good surface quality of hole Application in hydraulic chucks Alignment accurate tool holders Powerful machines Observe optimal coolant pressure Max. conc. error of clamped tool 0.02 mm Play-free spindles
Surface Type RT 150 GG Cutting direction rh Point grinding Facet point Point angle 130 Web thinned 3.00 Standard range, page 538 Guhring no. 770 Standard Guhring std. Tool material Solid carbide
Very good self-centering characteristics High productivity High cutting rates Close diameter tolerances Very good surface quality of hole Application in hydraulic chucks Alignment accurate tool holders Powerful machines Observe optimal coolant pressure Max. conc. error of clamped tool 0.02 mm Play-free spindles
Surface Type RT 150 GG Cutting direction rh Point grinding Relieved cone Point angle 120 Web thinned 3.00 Standard range, page 540 Guhring no. 6070 Standard Guhring std. Tool material Solid carbide
Very good self-centering characteristics High productivity High cutting rates Close diameter tolerances Very good surface quality of hole Application in hydraulic chucks Alignment accurate tool holders Powerful machines Observe optimal coolant pressure Max. conc. error of clamped tool 0.02 mm Play-free spindles
Surface Type RT 150 GG Cutting direction rh Point grinding Facet point Point angle 130 Web thinned 3.00 Standard range, page 540
bright
steam tempered
nitrided lands
nitrided
golden brown
TiAlN
178
Ratio drills
Ratio drills with oil feed Guhring no. 773 Standard Guhring std. Tool material Solid carbide
Negative helix Extremely quiet spotting characteristics High dynamic stability For dimensionally very accurate holes Very good surface quality of hole Application in hydraulic chucks Alignment accurate tool holders Powerful machines Observe optimal coolant pressure Max. conc. error of clamped tool 0.02 mm Play-free spindles aluminium and Al alloys with high Si-content cast iron Ratio drills
Surface Type RT 150 GN Cutting direction rh Point grinding Relieved cone Point angle 120 Web thinned 5.00 Standard range, page 542 Guhring no. 1171 Standard DIN 6538 K Tool material Carbide
HSS holder with brazed carbide insert Special geometry Dampens vibrations and shocks Highest cutting rates (see Guroguide) Optimal chip fracture and short chips Close diameter tolerances Alignment accurate holes Alignment accurate tool holders Coolant press./volume s. Techn. Section Powerful machines Max. conc. error of clamped tool 0.02 mm
unalloyed/low alloyed steels grey cast/spheroidal graphite iron brass, bronzes, plastics graphite
Surface Type RT 80 U Cutting direction rh Point grinding Relieved cone Point angle 140 Web thinned 9.50 Standard range, page 543 Guhring no. 1172 Standard DIN 6538 M Tool material Carbide
HSS holder with brazed carbide insert Special geometry Dampens vibrations and shocks Highest cutting rates (see Guroguide) Optimal chip fracture and short chips Close diameter tolerances Alignment accurate holes Alignment accurate tool holders Coolant press./volume s. Techn. Section Powerful machines Max. conc. error of clamped tool 0.02 mm
unalloyed/low alloyed steels grey cast/spheroidal graphite iron brass, bronzes, plastics graphite
Surface Type RT 80 U Cutting direction rh Point grinding Relieved cone Point angle 140 Web thinned 9.50 Standard range, page 546 Guhring no. 1173 Standard DIN 6538 L Tool material Carbide
HSS holder with brazed carbide insert Special geometry Dampens vibrations and shocks Highest cutting rates (see Guroguide) Optimal chip fracture and short chips Close diameter tolerances Alignment accurate holes Alignment accurate tool holders Coolant press./volume s. Techn. Section Powerful machines Max. conc. error of clamped tool 0.02 mm
unalloyed/low alloyed steels grey cast/spheroidal graphite iron brass, bronzes, plastics graphite
Surface Type RT 80 U Cutting direction rh Point grinding Relieved cone Point angle 140 Web thinned 9.50 Standard range, page 548 Guhring no. 2713 Standard DIN 6537 L Tool material Solid carbide
Short design Wide flutes Three flutes Optimal centering Very high feed rates Spotting on oblique surfaces Application under difficult conditions Reboring with interrupted cutting Maximum process reliability
Surface Type FT 200 G Cutting direction rh Point grinding Spiro-point Point angle 130 Web thinned 3.00 Standard range, page 550
AlTiN
TiCN
FIRE
AlCrN
TiN
MolyGlide
179
Ratio drills
Ratio drills 3-flute
Ratio drills
Guhring no. 2939 Standard DIN 6537 L Tool material Solid carbide
Short design Wide flutes Three flutes Optimal centering Very high feed rates Spotting on oblique surfaces Application under difficult conditions Reboring with interrupted cutting Maximum process reliability
Surface Type FT 200 G Cutting direction rh Point grinding Spiro-point Point angle 130 Web thinned 5.00 Standard range, page 550
Guhring no. 1027 Standard DIN 6539 Tool material Solid carbide
Three flutes Very good self-centering characteristics For dimensionally very accurate holes Very good surface quality of hole
Surface Type GS 200 F Cutting direction rh Point grinding Facet point Point angle 150 Web thinned Standard range, page 552
Guhring no. 745 Standard DIN 6539 Tool material Solid carbide
Three flutes Very good self-centering characteristics For dimensionally very accurate holes Very good surface quality of hole
grey and chilled cast iron short chipping brass, bronze short chipping aluminium alloys AlSi-alloys with high Si content fiber reinforced plastics Duroplastics, hardened steels
Surface Type GS 200 G Cutting direction rh Point grinding Facet point Point angle 150 Web thinned Standard range, page 552
Guhring no. 1020 Standard DIN 6539 Tool material Solid carbide
Three flutes Very good self-centering characteristics For dimensionally very accurate holes Very good surface quality of hole
grey and chilled cast iron short chipping brass, bronze short chipping aluminium alloys AlSi-alloys with high Si content fiber reinforced plastics Duroplastics, hardened steels
Surface Type GS 200 G Cutting direction lh Point grinding Facet point Point angle 150 Web thinned Standard range, page 552
Guhring no. 1024 Standard DIN 6539 Tool material Solid carbide
Three flutes Very good self-centering characteristics For dimensionally very accurate holes Very good surface quality of hole
grey and chilled cast iron short chipping brass, bronze short chipping aluminium alloys AlSi-alloys with high Si content fiber reinforced plastics Duroplastics, hardened steels
Surface Type GS 200 G Cutting direction rh Point grinding Facet point Point angle 150 Web thinned Standard range, page 552
bright
steam tempered
nitrided lands
nitrided
golden brown
TiAlN
180
Ratio drills
Ratio drills 3-flute Guhring no. 1025 Standard DIN 6539 Tool material Solid carbide
Three flutes Very good self-centering characteristics For dimensionally very accurate holes Very good surface quality of hole grey cast iron long chipping Al cast alloys Ratio drills
Surface Type GS 200 G Cutting direction rh Point grinding Facet point Point angle 150 Web thinned Standard range, page 553
Guhring no. 1028 Standard DIN 6539 Tool material Solid carbide
Three flutes Very good self-centering characteristics For dimensionally very accurate holes Very good surface quality of hole
Surface Type GS 200 G Cutting direction lh Point grinding Facet point Point angle 150 Web thinned Standard range, page 553
Guhring no. 1029 Standard DIN 6539 Tool material Solid carbide
Three flutes Very good self-centering characteristics For dimensionally very accurate holes Very good surface quality of hole
Surface Type GS 200 G Cutting direction lh Point grinding Facet point Point angle 150 Web thinned Standard range, page 553
Guhring no. 611 Standard DIN 6539 Tool material Solid carbide
Three flutes Very good self-centering characteristics For dimensionally very accurate holes Very good surface quality of hole
Surface Type GS 200 U Cutting direction rh Point grinding Facet point Point angle 150 Web thinned Standard range, page 553
Guhring no. 731 Standard DIN 6539 Tool material Solid carbide
Three flutes Very good self-centering characteristics For dimensionally very accurate holes Very good surface quality of hole
Surface Type GS 200 U Cutting direction rh Point grinding Facet point Point angle 150 Web thinned Standard range, page 553
AlTiN
TiCN
FIRE
AlCrN
TiN
MolyGlide
181
Ratio drills
Ratio drills 3-flute
Ratio drills
Guhring no. 1021 Standard DIN 6539 Tool material Solid carbide
Three flutes Very good self-centering characteristics For dimensionally very accurate holes Very good surface quality of hole
Surface Type GS 200 U Cutting direction lh Point grinding Facet point Point angle 150 Web thinned Standard range, page 553
Guhring no. 1032 Standard Guhring std. Tool material Solid carbide
Three flutes Very good self-centering characteristics For dimensionally very accurate holes Very good surface quality of hole
grey and chilled cast iron short chipping brass, bronze short chipping aluminium alloys AlSi-alloys with high Si content fiber reinforced plastics Duroplastics, hardened steels
Surface Type GS 200 G Cutting direction rh Point grinding Facet point Point angle 150 Web thinned Standard range, page 562
Guhring no. 1034 Standard Guhring std. Tool material Solid carbide
Three flutes Very good self-centering characteristics For dimensionally very accurate holes Very good surface quality of hole
grey and chilled cast iron short chipping brass, bronze short chipping aluminium alloys AlSi-alloys with high Si content fiber reinforced plastics Duroplastics, hardened steels
Surface Type GS 200 G Cutting direction rh Point grinding Facet point Point angle 150 Web thinned Standard range, page 562
Guhring no. 1033 Standard Guhring std. Tool material Solid carbide
Three flutes Very good self-centering characteristics For dimensionally very accurate holes Very good surface quality of hole
Surface Type GS 200 U Cutting direction rh Point grinding Facet point Point angle 150 Web thinned Standard range, page 562
bright
steam tempered
nitrided lands
nitrided
golden brown
TiAlN
182
Product information Standard For the production of tapping size holes Tool material with a 90 chamfer. Ideal combination: Surface finish Ratio drill plus chamfer collar FR 90. In comparison with other designs, the FR Type 90 has the main advantage of also being Cutting direction suitable for use with standard carbide and high speed steel drills, with or without Grinding coolant ducts and with slow or quick helix Point angle angles. Modifications to the shank i.e. whistle notch flats or to the drill body for Web thinned the indexable insert are not necessary. Es pecially suitable for the drilling of cast iron Standard range, page and AlSi-alloys, but also for structural and heat-treatable steels.
adjustment ring size adjustment ring size A/B L max clamping length l4 adjustment s2=6 mm L min A/B clamping length l4
582
d1
45
d1
d2
adjustment
s1=6 mm
size l2 mm d1 > mm d2 mm l4 mm L L L L
max
1 29 4,9 6 36 15 3
2 29 5-6 6 36 15 3
3 29 6-7 8 36 12 0 24 12 12 0
4 29 7-8 8 36 12 0 24 12 12 0
5 33 8-9 10 40 14 2 28 16 16 4
6 33 9-10 10 40 14 2 28 16 16 4
7 33 12 45 22 10 10 0 38 26 26 14
8 33 12 45 22 10 10 0 38 26 26 14
9 39 12-13 14 45 21 9 9 0 38 26 26 14
10 39 13-14 14 45 21 9 9 0 38 26 26 14
11 39 14-15 16 48 26 14 14 2 44 32 32 20
d2
12 39 15-16 16 48 26 14 14 2 44 32 32 20
13 45 18 48 28 16 16 4 48 36 36 24
14 45 18 48 28 16 16 4 48 36 36 24
10-11 11-12
16-17 17-18
3x D
A B A B
L L L L
min
max min
max min
5x D
max min
Guhring no.
1156
Guhring no.
1056
Standard Guhring std. Tool material Solid carbide Carbide grade K Surface finish Standard range, page 582 Guhring no. 145 Chamfer collar Standard range, page 583 Guhring no. 1054 Adjustment ring Standard range, page 583 Guhring no. 1072 Torx screw Standard range, page 583 Guhring no. 1612 Screw driver
Schraubendreher
Standard Guhring std. Tool material Solid carbide Carbide grade K/P Surface finish Standard range, page 582 Guhring no. 1053 Clamping sleeve Standard range, page 583 Guhring no. 1055 Clamping piece Standard range, page 582 Guhring no. 4072 Adjusting element Standard range, page 582 Guhring no. 4912 Screw driver Standard range, page 583
AlCrN TiN MolyGlide
AlTiN
183
Chamfer collar Fr 90
Guhring no.
1052
Product information Type HT 800 WP was specially developed for the economic production of larger (11.5 - 25.99 mm ), more accurate and deep holes in cast materials, Al and Al-alloys. The compact design gives the tool increased rigidity, allowing cosiderably higher feed rates compared to conventional tools with indexable or interchangeable inserts. The optimised flute profile causes outstanding chip flow, preventing chip congestion especially with deep holes. Self centering interchangeable insert geometry, chip formation in the interchangeable insert. Patented interchangeable insert clamping principle.
HT 800 WP
Guhring no. 4042 Standard Guhring std. Type HT 800 WP Cutting direction rh Drilling depth 3 x D Shank DIN 6535, form HE, collar DIN 6595 Coolant supply through the body Standard range, page 564
HT 800 WP
Guhring no. 4043 Standard Guhring std. Type HT 800 WP Cutting direction rh Drilling depth 5 x D Shank DIN 6535, form HE, collar DIN 6595 Coolant supply through the body Standard range, page 564
HT 800 WP
Guhring no. 4048 Standard Guhring std. Type HT 800 WP Cutting direction rh Drilling depth 7 x D Shank DIN 6535, form HE, collar DIN 6595 Coolant supply through the body Standard range, page 564 Guhring no. 4024 Standard Guhring std. Tool material Solid carbide Carbide grade K Surface finish Point grinding/angle relieved cone/140 Web thinned Ratio Standard range, page 566 Guhring no. 4026 Standard Guhring std. Tool material Solid carbide Carbide grade K/P Surface finish Point grinding/angle relieved cone/140 Web thinned Ratio Standard range, page 566 Guhring no. 4025 Standard Guhring std. Tool material Solid carbide Carbide grade K/P Surface finish Point grinding/angle relieved cone/140 Web thinned Ratio Standard range, page 566 Guhring no. 4071 Clamping screw Standard range, page 567 Guhring no. 1612 Screw driver Standard range, page 567
nitrided golden brown TiAlN
bright
steam tempered
nitrided lands
184
detail A...A
interchangeable insert tool holder A A clamping screw (with conical point) Torx Md marking for clamping screw stop screw (fixed position)
Product information Type RT 800 WP was specially developed for the economic production of larger (16.0 - 40.5 mm ), more accurate and deep holes in steel, cast iron and Al-alloys. The compact design gives the tool increased rigidity, allowing cosiderably higher feed rates compared to conventional tools with indexable or interchangeable inserts (see Guhringguide). The insert has rounded lands allowing a hole quality to IT9. Precise centering of interchangeable inserts thanks to locating spigot on connecting surface.
RT 800 WP
Guhring no. 5242 Standard Guhring std. Type RT 800 WP Cutting direction rh Drilling depth 3 x D Shank DIN 6535, form HE Coolant supply through the body Standard range, page 568
RT 800 WP
Guhring no. 5243 Standard Guhring std. Type RT 800 WP Cutting direction rh Drilling depth 5 x D Shank DIN 6535, form HE Coolant supply through the body Standard range, page 568
RT 800 WP
Guhring no. 5248 Standard Guhring std. Type RT 800 WP Cutting direction rh Drilling depth 7 x D Shank DIN 6535, form HE, collar DIN 6595 Coolant supply through the body Standard range, page 568 Guhring no. 2747 Standard Guhring std. Tool material Solid carbide Carbide grade K Surface finish Point grinding/angle relieved cone/140 Web thinned Ratio Standard range, page 570 Guhring no. 2485 Standard Guhring std. Tool material Solid carbide Carbide grade K/P Surface finish Point grinding/angle relieved cone/140 Web thinned Ratio Standard range, page 570 Guhring no. 1071 Standard Guhring std. Clamping screw Standard range, page 571
Schraubendreher
Guhring no. 1047 Standard Guhring std. Tool material Solid carbide Carbide grade K/P Surface finish Point grinding/angle relieved cone/140 Web thinned Ratio Standard range, page 570 Guhring no. 4915 Standard Guhring std. Torque key Standard range, page 571 Guhring no. 1612 Standard Guhring std. Clamping screw Standard range, page 571 Guhring no. 4917 Standard Guhring std. Torx-Bit Standard range, page 571
AlCrN TiN MolyGlide
AlTiN
TiCN
FIRE
185
LT 800 WP
System summary
SK holders
4512 4510
holder size
nom.* range
400
(4042.9)
430
(4345.9)
100
100.063
460
(4648.9)
100
490
(4951.9)
100
140.063
140
520
(5255.9)
100
100.063
100
560
(5659.9)
100
140.063
140
When ordering please always state Guhring no. and code no! * for intermediate please consult Guhring application technician. direct installation in the spindle
bright
steam tempered
nitrided lands
nitrided
golden brown
TiAlN
186
LT 800 WP
Tooling system T800
holder size
LTLT 800-Systembersicht heads Cartridges 800-Systembersicht Extensions Drill for mounting Seite 5 5 Seite 3xD 1xD the external A58 00042 spiral design 1500042 A58
4148 4150 4160
4142
nom.* range
40.0
40.046 40.043
40.046
105
63.105
105
0.5 x D
10.150
43.046
150
150
46.056 46.049
180
63.180
180
2xD
46.056 49.052
46.056
53.0 54.0
120
63.120
120
0.5 x D
12.180
52.056
55.0 56.0
180
180
56.065
57.0 58.0
210
63.210
210
2xD
560
56.060
59.0
HSK
size
100100
80 80
63 63
AlTiN
TiCN
FIRE
AlCrN
TiN
MolyGlide
187
LT 800 WP
System summary
SK holders
4512 4510
Extensions
4549
600
(6064.9)
650
(6569.9)
700
(7074.9)
750
(7579.9)
800
(8084.9)
850
(8589.9)
900
(9094.9)
950
(95100)
60.0 61.0 62.0 63.0 64.0 65.0 66.0 67.0 68.0 69.0 70.0 71.0 72.0 73.0 74.0 75.0 76.0 77.0 78.0 79.0 80.0 81.0 82.0 83.0 84.0 85.0 86.0 87.0 88.0 89.0 90.0 91.0 92.0 93.0 94.0 95.0 96.0 97.0 98.0 99.0 100.0
100
100.063
100
140
100
50.080
120.080 50.080
120
80.100
120
160.080
160
60.080
60.100 140.100
140
60.100
200.100
200
When ordering please always state Guhring no. and code no! * for intermediate please consult Guhring application technician. direct installation in the spindle
bright
steam tempered
nitrided lands
nitrided
golden brown
TiAlN
188
LT 800 WP
Tooling system T800
holder size
Cartridges
4160
4149
4150
nom.* range
56.065
63.135
135
0,5 x D
40.210
060.065
63.240
240
2xD
210
65.070
70.075 070.075
80.160
160
0,5 x D
75.080 48.255 075.080
255
105
80.290
290
2xD
150
080.085
80.090
180
80.090 085.090
100.180
180
0,5 x D
90.100 58.300 090.095
120
300
100.330
330
210
2xD
180
90.100 095.100
60.0 61.0 62.0 63.0 64.0 65.0 66.0 67.0 68.0 69.0 70.0 71.0 72.0 73.0 74.0 75.0 76.0 77.0 78.0 79.0 80.0 81.0 82.0 83.0 84.0 85.0 86.0 87.0 88.0 89.0 90.0 91.0 92.0 93.0 94.0 95.0 96.0 97.0 98.0 99.0 100.0
950
HSK
size
100
80
100 63
80
63
AlTiN
TiCN
FIRE
AlCrN
TiN
MolyGlide
189
LT 800 WP
Summary Central inserts and external inserts for drilling head Std. range, page 572 Central interchangeable inserts
Guhring no.
Tool material Carbide grade Surface finish especially suitable for cast materials aluminium/Al-alloys plastics universal steel and cast machining universal steel and cast machining
4179
with circular lands
4180
with circular lands
4181
with circular lands
4182
with circular lands
09
size
size
12
4170
with circular lands
4171
with circular lands
4172
with circular lands
4173
with circular lands
05
size
size
06
bright
steam tempered
nitrided lands
nitrided
golden brown
TiAlN
190
LT 800 WP
Tooling system T800
400 430
27
30
400
for size
560
for size
950
for size
28
31
34
27
for size for size for size Durchmesserregulierung durch Distanzstck Art:-Nr. 4168 400 560 950 700 32 (am Beispiel der Trger-Gre 950) Diameter adjustment with Dateiname: A58 durch Distanzstck Art:-Nr. 4168 Durchmesserregulierung00039 distance pieces on both sides
Durchmesserregulierung durch Distanzstck Art:-Nr. 4168 (am Beispiel der Trger-Gre 950) 650 Dateiname: A58 00039
(am Beispiel der Trger-Gre 950) (using holder size 950 as example) Dateiname: A58 00039 95,0 96,0 97,0
750
98,0
99,0
100,0
Thickness t in mm
800 850
34
100,0
95,0 ,0
96,0
97,0
97,0
98,0
98,0 99,0
100,0
99,0
900 950
0.50
AlTiN
32
34
1.00
TiCN
1.50
FIRE
2.0
AlCrN
1.00/1.50
TiN MolyGlide
191
Step drills
Stepped drills for centering to DIN 332
Step drills
60 countersink angle For tapping size holes with centre To DIN 332, sheet 2, form D Application on centering/cut-off mach.
Surface Type N Cutting direction rh Point grinding Relieved cone Point angle 118 Web thinned 3.30 Standard range, page 585
60 countersink angle For tapping size holes with centre To DIN 332, sheet 2, form DR Application on centering/cut-off mach.
Surface Type N Cutting direction rh Point grinding Relieved cone Point angle 118 Web thinned 3.30 Standard range, page 585
Shank without flat 60 countersink angle For tapping size holes with centre To DIN 332, sheet 2, form D
Surface Type N Cutting direction rh Point grinding Relieved cone Point angle 118 Web thinned 6.80 Standard range, page 586
Shank without flat 60 countersink angle For tapping size holes with centre To DIN 332, sheet 2, form D
Surface Type N Cutting direction rh Point grinding Relieved cone Point angle 118 Web thinned 3.30 Standard range, page 587
Very high torsional stability For CNC and NC machines For through holes to DIN EN 20 273 for screwhead countersinks 90 f dependent on small diameter vc dependent on large diameter
Surface Type N Cutting direction rh Point grinding Relieved cone Point angle 118 Web thinned 3.20 Standard range, page 588
bright
steam tempered
nitrided lands
nitrided
golden brown
TiAlN
192
Step drills
Straight shank short step drills Guhring no. 1147 Tool material HSS
Very high torsional stability For CNC and NC machines For through holes to DIN EN 20 273 for screwhead countersinks 90 f dependent on small diameter vc dependent on large diameter Step drills
Standard Guhring std. Surface Type N Cutting direction rh Point grinding Relieved cone Point angle 118 Web thinned 3.40 Standard range, page 588 Straight shank short step drills Guhring no. 379 Standard Guhring std. Tool material HSS
Very high torsional stability For CNC and NC machines For through holes To DIN EN 20 273 For screwhead countersinks 180 to DIN 974-1 For screws To DIN 6912, 7513, 7984 f dependent on small diameter vc dependent on large diameter
Surface Type N Cutting direction rh Point grinding Relieved cone Point angle 118 Web thinned 3.40 Standard range, page 589
Very high torsional stability For CNC and NC machines For tapping size holes To DIN 336 For countersinking 90 To DIN EN 20 273 f dependent on small diameter vc dependent on large diameter
Surface Type N Cutting direction rh Point grinding Relieved cone Point angle 118 Web thinned 2.50 Standard range, page 590
fine tolerance For through holes To DIN EN 20 273 For screwhead countersinks 90 f dependent on small diameter vc dependent on large diameter
Surface Type N Cutting direction rh Point grinding Relieved cone Point angle 118 Web thinned 3.20 Standard range, page 591
For through holes To DIN EN 20 273 For screwhead countersinks 90 form A To DIN 74 f dependent on small diameter vc dependent on large diameter
Surface Type N Cutting direction rh Point grinding Relieved cone Point angle 118 Web thinned 3.40 Standard range, page 591
AlTiN
TiCN
FIRE
AlCrN
TiN
MolyGlide
193
Step drills
Straight shank subland drills
Step drills
For through holes To DIN EN 20 273 For screwhead countersinks 180 To DIN 974-1 For screws To DIN 6912, 7513, 7984 f dependent on small diameter vc dependent on large diameter
Surface Type N Cutting direction rh Point grinding Relieved cone Point angle 118 Web thinned 3.20 Standard range, page 591
For through holes To DIN EN 20 273 For screwhead countersinks 180 To DIN 974-1 For screws To DIN 6912, 7513, 7984 f dependent on small diameter vc dependent on large diameter
Surface Type N Cutting direction rh Point grinding Relieved cone Point angle 118 Web thinned 3.40 Standard range, page 592
Guhring no. 738 Standard Guhring std. Tool material Solid carbide
For through holes To DIN EN 20 273 For screwhead countersinks 180 To DIN 974-1 For screws To DIN 6912, 7513, 7984 f dependent on small diameter vc dependent on large diameter
abrasive materials AlSi alloys fiber-reinforced plastics Duroplastics liable to cause severe abrasion on cutting lips and lands high tensile steels, cast steel grey cast iron, chilled cast iron, CrNi-steels, bronzes, light metals
Surface Type N Cutting direction rh Point grinding Relieved cone Point angle 118 Web thinned 3.40 Standard range, page 592
For through holes to DIN EN 20273 For screwhead countersinks 180 For screws To DIN 6912 f dependent on small diameter vc dependent on large diameter
Surface Type N Cutting direction rh Point grinding Relieved cone Point angle 118 Web thinned 5.90 Standard range, page 593
For tapping size holes To DIN 336 For countersinking 90 For through holes To DIN EN 20 273 f dependent on small diameter vc dependent on large diameter
Surface Type N Cutting direction rh Point grinding Relieved cone Point angle 118 Web thinned 2.50 Standard range, page 594
bright
steam tempered
nitrided lands
nitrided
golden brown
TiAlN
194
Step drills
Straight shank subland drills Guhring no. 739 Tool material Solid carbide
For tapping size holes To DIN 336 For countersinking 90 For through holes To DIN EN 20 273 f dependent on small diameter vc dependent on large diameter abrasive materials AlSi alloys fiber-reinforced plastics Duroplastics liable to cause severe abrasion on cutting lips and lands high tensile steels, cast steel grey cast iron, chilled cast iron, CrNi-steels, bronzes, light metals Step drills
Standard Guhring std. Surface Type N Cutting direction rh Point grinding Relieved cone Point angle 118 Web thinned 2.50 Standard range, page 594 Taper shank subland drills Guhring no. 537 Standard DIN 8375 Tool material HSS
fine tolerance For through holes To DIN EN 20 273 For screwhead countersinks 90 f dependent on small diameter vc dependent on large diameter
Surface Type N Cutting direction rh Point grinding Relieved cone Point angle 118 Web thinned 5.50 Standard range, page 595
fine tolerance For through holes To DIN EN 20 273 For screwhead countersinks 90 f dependent on small diameter vc dependent on large diameter
Surface Type N Cutting direction rh Point grinding Relieved cone Point angle 118 Web thinned 6.40 Standard range, page 596
For through holes To DIN EN 20 273 For screwhead countersinks 180 To DIN 974-1 For screws To DIN 6912, 7513, 7984 f dependent on small diameter vc dependent on large diameter
Surface Type N Cutting direction rh Point grinding Relieved cone Point angle 118 Web thinned 5.30 Standard range, page 597
For through holes To DIN EN 20 273 For screwhead countersinks 180 To DIN 974-1 For screws To DIN 6912, 7513, 7984 f dependent on small diameter vc dependent on large diameter
Surface Type N Cutting direction rh Point grinding Relieved cone Point angle 118 Web thinned 5.50 Standard range, page 598
AlTiN
TiCN
FIRE
AlCrN
TiN
MolyGlide
195
Step drills
Taper shank subland drills
Step drills
For through holes To DIN EN 20 273 For screwhead countersinks 180 To DIN 974-1 For screws To DIN 6912, 7513, 7984 f dependent on small diameter vc dependent on large diameter
abrasive materials AlSi alloys fiber-reinforced plastics Duroplastics liable to cause severe abrasion on cutting lips and lands high tensile steels, cast steel grey cast iron, chilled cast iron, CrNi-steels, bronzes, light metals
Surface Type N Cutting direction rh Point grinding Relieved cone Point angle 118 Web thinned 9.00 Standard range, page 598
For through holes With old countersinks form H, J, K To DIN 75, part 2 For screws To DIN 84, 912, 6712 f dependent on small diameter vc dependent on large diameter
Surface Type N Cutting direction rh Point grinding Relieved cone Point angle 118 Web thinned 5.30 Standard range, page 599
For tapping size holes To DIN 336, part 1 For countersinking 90 To DIN 20 273 f dependent on small diameter vc dependent on large diameter
Surface Type N Cutting direction rh Point grinding Relieved cone Point angle 118 Web thinned 6.80 Standard range, page 600
Surface Type Cutting direction rh Point grinding Relieved cone Point angle 118 Web thinned 1.60 Standard range, page 601
Surface Type Cutting direction rh Point grinding Relieved cone Point angle 118 Web thinned 1.60 Standard range, page 602
bright
steam tempered
nitrided lands
nitrided
golden brown
TiAlN
196
Center drills
Center drills without flat Guhring no. 292 Standard B.S. 328 Tool material HSS
For centre holes Form A to British standards Center drills
Surface Type Cutting direction rh Point grinding Relieved cone Point angle 118 Web thinned 1.19 Standard range, page 603
Surface Type Cutting direction lh Point grinding Relieved cone Point angle 118 Web thinned 1.19 Standard range, page 603
Without protected countersink For centre holes To DIN 332, sheet 1, form A
Surface Type Cutting direction rh Point grinding Relieved cone Point angle 118 Web thinned 1.60 Standard range, page 604
Without protected countersink For centre holes To DIN 332, sheet 1, form A
Surface Type Cutting direction lh Point grinding Relieved cone Point angle 118 Web thinned 1.60 Standard range, page 604
Especially high rigidity Correct positioning between lathe centers For centre holes To DIN 332, sheet 1, form R
Surface Type Cutting direction rh Point grinding Relieved cone Point angle 118 Web thinned 1.60 Standard range, page 604
AlTiN
TiCN
FIRE
AlCrN
TiN
MolyGlide
197
Center drills
Center drills without flat
Center drills
Especially high rigidity Correct positioning between lathe centers For centre holes To DIN 332, sheet 1, form R
Surface Type Cutting direction lh Point grinding Relieved cone Point angle 118 Web thinned 1.60 Standard range, page 604
Without protected countersink For centre holes To DIN 332, sheet 1, form A
Surface Type Cutting direction rh Point grinding Relieved cone Point angle 118 Web thinned 1.60 Standard range, page 605
Especially high rigidity Correct positioning between lathe centers For centre holes To DIN 332, sheet 1, form R
Surface Type Cutting direction rh Point grinding Relieved cone Point angle 118 Web thinned 1.60 Standard range, page 605
Co-alloyed high speed steel Without protected countersink Increased wear resistance For centre holes To DIN 332, sheet 1, form A
Surface Type Cutting direction rh Point grinding Relieved cone Point angle 118 Web thinned 1.60 Standard range, page 605
With heel Without protected countersink Recess between countersink and hole Especially high rigidity High cutting rates For centre holes To DIN 332, sheet 1, form A
Surface Type Cutting direction rh Point grinding Relieved cone Point angle 118 Web thinned 1.60 Standard range, page 605
bright
steam tempered
nitrided lands
nitrided
golden brown
TiAlN
198
Center drills
Center drills without flat Guhring no. 736 Standard Guhring std. Tool material Solid carbide
Without protected countersink For centre holes To DIN 332, sheet 1, form A d1 0.8 mm: not double ended abrasive materials AlSi alloys fiber-reinforced plastics Duroplastics liable to cause severe abrasion on cutting lips and lands high tensile steels, cast steel grey cast iron, chilled cast iron, CrNi-steels, bronzes, light metals Center drills
Surface Type Cutting direction rh Point grinding Relieved cone Point angle 118 Web thinned 1.60 Standard range, page 605
Without protected countersink For centre holes To DIN 332, sheet 1, form A d1 0.8 mm: not double ended
Surface Type Cutting direction rh Point grinding Relieved cone Point angle 118 Web thinned 1.60 Standard range, page 606
Without protected countersink For centre holes To DIN 332, sheet 1, form A d1 0.8 mm: not double ended
Surface Type Cutting direction lh Point grinding Relieved cone Point angle 118 Web thinned 1.60 Standard range, page 606
Especially high rigidity Correct positioning between lathe centers For centre holes To DIN 332, sheet 1, form R d1 0.8 mm: not double ended
Surface Type Cutting direction rh Point grinding Relieved cone Point angle 118 Web thinned 1.60 Standard range, page 606
Especially high rigidity Correct positioning between lathe centers For centre holes To DIN 332, sheet 1, form R
Surface Type Cutting direction lh Point grinding Relieved cone Point angle 118 Web thinned 1.60 Standard range, page 606
AlTiN
TiCN
FIRE
AlCrN
TiN
MolyGlide
199
Center drills
Center drills without flat
Center drills
For centre holes To DIN 332, sheet 1, form B With protected 120 countersink
Surface Type Cutting direction rh Point grinding Relieved cone Point angle 118 Web thinned 1.60 Standard range, page 607
For centre holes To DIN 332, sheet 1, form B With protected 120 countersink
Surface Type Cutting direction lh Point grinding Relieved cone Point angle 118 Web thinned 1.60 Standard range, page 607
With heel Recess between countersink and hole Especially high rigidity High cutting rates For centre holes To DIN 332, sheet 1, form B With protected 120 countersink d1 0.8 mm: not double ended
Surface Type Cutting direction rh Point grinding Relieved cone Point angle 118 Web thinned 1.60 Standard range, page 607
Long special drill Without protected countersink For centre holes To DIN 332, sheet 1, form A For deep centering positions
Surface Type Cutting direction rh Point grinding Relieved cone Point angle 118 Web thinned 1.60 Standard range, page 608
For centre holes To DIN 332, sheet 1, form B With protected 120 countersink
Surface Type Cutting direction rh Point grinding Relieved cone Point angle 118 Web thinned 1.60 Standard range, page 609
bright
steam tempered
nitrided lands
nitrided
golden brown
TiAlN
200
Center drills
Center drills without flat Guhring no. 286 Standard Guhring std. Tool material HSS
For centre holes To DIN 332, sheet 1, form B With protected 120 countersink Center drills
Surface Type Cutting direction lh Point grinding Relieved cone Point angle 118 Web thinned 1.60 Standard range, page 609
Without protected countersink For centre holes To DIN 332, sheet 1, form A
Surface Type Cutting direction rh Point grinding Relieved cone Point angle 118 Web thinned 1.60 Standard range, page 610
Especially high rigidity Correct positioning between lathe centers For centre holes To DIN 332, sheet 1, form R
Surface Type Cutting direction rh Point grinding Relieved cone Point angle 118 Web thinned 1.60 Standard range, page 610
Without protected countersink For centre holes To DIN 332, sheet 1, form A
Surface Type Cutting direction rh Point grinding Relieved cone Point angle 118 Web thinned 1.60 Standard range, page 611
Especially high rigidity Correct positioning between lathe centers For centre holes To DIN 332, sheet 1, form R
Surface Type Cutting direction rh Point grinding Relieved cone Point angle 118 Web thinned 1.60 Standard range, page 611
AlTiN
TiCN
FIRE
AlCrN
TiN
MolyGlide
201
Center drills
Center drills with flat
Center drills
For centre holes To DIN 332, sheet 1, form B With protected 120 countersink
Surface Type Cutting direction rh Point grinding Relieved cone Point angle 118 Web thinned 1.60 Standard range, page 612
For centre holes To DIN 332, sheet 1, form B With protected 120 countersink
Surface Type Cutting direction rh Point grinding Relieved cone Point angle 118 Web thinned 1.60 Standard range, page 613
Core drills Three flutes Especially high rigidity For pre-drilled/-cast/-punched holes Corrects alignment inaccuracies Corrects circularity errors Improved surface quality of hole Observe min. pilot hole dia. Chamfer dia. < tapping size hole Perf. finish reaming after core drilling
steels over 1000 N/mm cast iron over 240 Brinell Mn-steels, AlSi alloys hard and abrasive plastics
Surface Type N Cutting direction rh Point grinding Relieved cone Point angle 120 Web thinned Standard range, page 614
Core drills Three flutes Especially high rigidity For pre-drilled/-cast/-punched holes Corrects alignment inaccuracies Corrects circularity errors Improved surface quality of hole Observe min. pilot hole dia. Chamfer dia. < tapping size hole Perf. finish reaming after core drilling
Surface Type N Cutting direction rh Point grinding Relieved cone Point angle 120 Web thinned Standard range, page 615
Core drills, carbide tipped Especially high rigidity For pre-drilled/-cast/-punched holes Corrects alignment inaccuracies Corrects circularity errors Improved surface quality of hole Observe min. pilot hole dia. Chamfer dia. < tapping size hole Perf. finish reaming after core drilling
steels over 1000 N/mm cast iron over 240 Brinell Mn-steels, AlSi alloys hard and abrasive plastics
Surface Type N Cutting direction rh Point grinding Relieved cone Point angle 120 Web thinned Standard range, page 618
bright
steam tempered
nitrided lands
nitrided
golden brown
TiAlN
202
Core drills
Taper shank core drills Guhring no. 534 Tool material HSS
Core drills Three flutes Especially high rigidity For pre-drilled/-cast/-punched holes Corrects alignment inaccuracies Corrects circularity errors Improved surface quality of hole Observe min. pilot hole dia. Chamfer dia. < tapping size hole Perf. finish reaming after core drilling Core drills
Standard DIN 343 Surface Type N Cutting direction rh Point grinding Relieved cone Point angle 120 Web thinned Standard range, page 619 Taper shank core drills Guhring no. 634 Standard DIN 343 Tool material HSCO
Core drills Co-alloyed high speed steel Especially high rigidity For pre-drilled/-cast/-punched holes Corrects alignment inaccuracies Corrects circularity errors Improved surface quality of hole Observe min. pilot hole dia. Chamfer dia. < tapping size hole Perf. finish reaming after core drilling
Surface Type N Cutting direction rh Point grinding Relieved cone Point angle 120 Web thinned Standard range, page 619
Core drills Especially high rigidity For pre-drilled/-cast/-punched holes Corrects alignment inaccuracies Corrects circularity errors Improved surface quality of hole Observe min. pilot hole dia. Chamfer dia. < tapping size hole Perf. finish reaming after core drilling
Surface Type N Cutting direction rh Point grinding Relieved cone Point angle 120 Web thinned Standard range, page 624
Core drills Co-alloyed high speed steel Especially high rigidity For pre-drilled/-cast/-punched holes Corrects alignment inaccuracies Corrects circularity errors Improved surface quality of hole Observe min. pilot hole dia. Chamfer dia. < tapping size hole Perf. finish reaming after core drilling
Surface Type N Cutting direction rh Point grinding Relieved cone Point angle 120 Web thinned Standard range, page 624
Shell core drills Multi-fluted Especially high rigidity For round and alignment accurate holes For pre-drilled/-cast/-punched holes Observe min. pilot hole dia. Chamfer dia. < tapping size hole Perf. finish reaming after core drilling
steels over 1000 N/mm cast iron over 240 Brinell Mn-steels, AlSi alloys hard and abrasive plastics
Surface Type N Cutting direction rh Point grinding Relieved cone Point angle 120 Web thinned Standard range, page 626
AlTiN
TiCN
FIRE
AlCrN
TiN
MolyGlide
203
Guhring no. 1434 Standard DIN 217 Standard range, page 628
Guhring no. 1437 Standard DIN 6888 Standard range, page 631
Guhring no. 1435 Standard Guhring std. Standard range, page 629
Guhring no. 1436 Standard Guhring std. Standard range, page 630
bright
steam tempered
nitrided lands
nitrided
golden brown
TiAlN
204
Oil feed adaptors Product information For Guhring oil feed drills (guhring no. 269, 271, 371 and 375) Suitable for all drilling machines. The oil feed drill fits direct into the spindle. Radially coolant via the ball race at the run-out of the flutes. The adaptor does not extend the drilling system. Longitudinal stability and torsional rigidity are completely maintained. Coolant: soluble oil. Thin cutting oil can be used. As a rule, coolant pumps are sufficient.
Guhring no. 230 Standard Guhring std. Standard range, page 632
AlTiN
TiCN
FIRE
AlCrN
TiN
MolyGlide
205