Beruflich Dokumente
Kultur Dokumente
Vishay Semiconductors
19026
MECHANICAL DATA
Pinning: 1 = Carrier OUT, 2 = GND, 3 = VS
DESCRIPTION
The TSOP98238 is a miniaturized sensor for receiving the modulated signal of infrared remote control systems. A PIN diode and preamplifier are assembled on a lead frame, the epoxy package is designed as an IR filter. The modulated output signal, carrier out, can be used for repeater applications and code learning applications. This component has not been qualified according to automotive specifications.
PARTS TABLE
CARRIER FREQUENCY 30 kHz to 50 kHz CODE LEARNING APPLICATIONS TSOP98238
BLOCK DIAGRAM
16833_10
APPLICATION CIRCUIT
TSOP98x38 R1 100 33 k C1 4.7 F VO R2 3.3 k R4 3 R3 680 Supply voltage +5V TSAL6400
2
21647
GND 0V
PIN
Control circuit
GND
Recommended circuit for best sensitivity of the TSOP98x38 in repeater applications. It limits the output voltage swing VO to about 1 V in order to avoid internal coupling. The high level output voltage VO should never be pulled to a voltage lower than 0.85 V by the external circuit under any ambient condition.
** Please see document Vishay Material Category Policy: www.vishay.com/doc?99902 www.vishay.com 1 Document Number: 81973 Rev. 1.2, 04-Feb-11
TSOP98238
IR Sensor Module for Remote Control Systems
ABSOLUTE MAXIMUM RATINGS
PARAMETER Supply voltage (pin 3) Supply current (pin 3) Output voltage (pin 1) Voltage at output to supply Output current (pin 1) Junction temperature Storage temperature range Operating temperature range Power consumption Soldering temperature Tamb 85 C t 10 s, 1 mm from case TEST CONDITION SYMBOL VS IS VO VS - VO IO Tj Tstg Tamb Ptot Tsd VALUE - 0.3 to + 6 5 - 0.3 to 5.5 - 0.3 to (VS + 0.3) 5 100 - 25 to + 85 - 25 to + 85 10 260 UNIT V mA V V mA C C C mW C
Vishay Semiconductors
Note Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect the device reliability.
Ee max. 1/2
30 45
W/m2 deg
Ee
t tpi - burst length VO tpi 6 carrier cycles is recommended for optimum function VOH
VOL
21648
The number of carrier- out-pulses might not be exactly same as the number of carrier cycles in tpi (input burst)
t
21649
30
35
40
45
50
55
60
www.vishay.com 2
TSOP98238
Vishay Semiconductors
IR Sensor Module for Remote Control Systems
850
950
1050
1150
94 8408
- Wavelength (nm)
10
20 30
0.4
0.2
10
20 30
0.4
0.2
www.vishay.com 3
TSOP98238
IR Sensor Module for Remote Control Systems
PACKAGE DIMENSIONS in millimeters
5 (4) 2.8 4.8
Vishay Semiconductors
R2
8.25 0.3
6.95 0.3
(5.55)
(1.54)
30.5 0.5 1.1 0.9
0.85 max.
2.54 nom.
0.5 max.
1.2 0.2
Marking area
R2
www.vishay.com 4
Disclaimer
ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, Vishay), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishays knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customers responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customers technical experts. Product specifications do not expand or otherwise modify Vishays terms and conditions of purchase, including but not limited to the warranty expressed therein. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk and agree to fully indemnify and hold Vishay and its distributors harmless from and against any and all claims, liabilities, expenses and damages arising or resulting in connection with such use or sale, including attorneys fees, even if such claim alleges that Vishay or its distributor was negligent regarding the design or manufacture of the part. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners.
www.vishay.com 1