Beruflich Dokumente
Kultur Dokumente
Hallmark MPEG-2 SD Channels SD MPEG-2 Digital/Analog Tier Application Quick Set-up Guide
Figure 2. Rear Panel (Base Model) 1. Connect the L-Band signal to RF1. 13V or 18V LNB power is only available on the RF1 port. The factory default setting for LNB power is OFF. 2. Connect a cable from the Video #2 BNC connector on the rear of the unit to a video monitor and the terminal block balanced audio outputs labeled AUDIO 1 to monitoring equipment. 3. Once the boot up sequence is completed, press the Menu button then press to Preset/Input Setup and press the SELECT button. 4. Press to Preset Signal then press the SELECT button. 5. Press and enter the following parameters: P#: 1 Freq(GHZ) 3.790500 SymRate 12.4000 FEC AUTO L-Band 1359.50
NOTE: When the frequency field is selected, a message stating video may be disabled will appear and you will be prompted to abort or continue. Select continue and proceed with data entry.
1 of 4
6.
Press again and enter the following parameters: P#: 1 Input IQ AUTO Net ID 1 Polarization Horiz Input RF 1
NOTE: Assuming all parameters and cabling have been done correctly; the signal led should be flashing. If not, recheck all connections and settings. If led is blinking, proceed to next step. 7. Press the Menu button. The message Acquired, Save should appear and you will be prompted again to abort or continue. If so, press to Continue and then press the SELECT button. 8. The receiver display should now be on the Startup Screen and the unit will default to the first available channel.
Table 1. RF Parameters Entry / Selection Satellite Downlink Frequency L-Band Frequency (equiv.) Symbol Rate FEC Modulation Rolloff Network ID Polarity RF Input LO #1 Frequency Orbital Location Power (LNB DC Power on RF1) Values AMC 11 3.790500 GHz 1359.50 MHz 12.4000 MSps AUTO DVB-S QPSK 0.35 1 H (Horizontal) #1 5.150 GHz 131 West OFF
to scroll through the available program 9. To change the channel to decode, use the channels or use the keypad to directly enter the program number. Press SELECT. NOTE: It is recommended for the analog or digital tier to use channels 111, 121, 131, or 141, because they have AC-3 audio. Use the (See Table 2 for Service Names and Channel Numbers).
2 of 4
Table 2. Hallmark SD Channel Assignments Channel Service Name Hallmark Channel East Hallmark Channel West Hallmark Movie Channel East Hallmark Movie Channel West Hallmark Channel East (AC-3) Hallmark Channel West (AC-3) Hallmark Movie Channel East (AC-3) Hallmark Movie Channel West (AC-3) Local Avail with 8 sec pre-roll Audio 1 is Stereo Left and Right (L & R) channels for all SD services. Audio 2 is DTMF Tones on the Left (L) channel and no audio on the Right (R) channel for the MPEG services. (See Local avails/commercial insertion at the end of this document for further information) ** NOTE! A displayed BER reading between 1.0E-03 and 0.0E-08 on the front panel of the PowerVu Receiver is needed to properly decode the signal. 10. After a short period of time you should get the message Channel XX Needs Authorization Key on your video monitor and the red Alarm light on the front display panel should be illuminated. 11. You will now need to follow the below steps under Authorizing D9850 Program Receiver Instructions to complete the installation and setup procedure. Numbers 11 21 31 41 111 121 131 141 Video (PID) 1260 1160 1360 1460 1260 1160 1360 1460 Audio 1 (PID) 1220 1120 1320 1420 1230 1330 1130 1430 Audio 2 (PID) 1222 1122 1322 1422 1231 1331 1131 1431 DPI (PID) 130 230 330 430 130 230 330 430 PMT (PID) 5011 5021 5031 5041 5111 5121 5131 5141
3 of 4
Customers Programmers and Broadcasters Telcos and Cable Service Providers All customers All customers
4 of 4