Beruflich Dokumente
Kultur Dokumente
Contents
Catalogue HY30-3245/UK
Contents
Introduction and general Information ..............................................................4 Technical Data ................................................................................................5 Ordering Code ................................................................................................6 Pressure Controls .........................................................................................18 Remote Pressure Controls ...........................................................................20 Load Sensing Controls .................................................................................22 Horse Power/Torque Controls .......................................................................26 Performance Curves .....................................................................................30 Electronic P/Q Controls ................................................................................32 Proportional Displacement Control...............................................................32 Electronic P/Q Controls ................................................................................33 Efficiency and Case Drain Flows ..................................................................34 Performance Curves and Case Drain Flows PV 360....................................39 Accessories Control......................................................................................40 Proportional pressure relief valve PVACRE* ................................................42 Accessories Control......................................................................................43 Dimensions ...................................................................................................44 Control Dimensions ......................................................................................56 Electronic Module PQDXXA .........................................................................60 Through Drive, Mounting Kits .......................................................................61 Through Drive, Flange Load Limitation ........................................................62 Multiple Pump Combinations - Maximum Moment .......................................62 Through Drive, Shaft Load Limitations .........................................................63 PV360 shaft options .....................................................................................64
Introduction
Catalogue HY30-3245/UK
General Information
Fluid recommendations Premium quality hydraulic mineral fluid is recomended, like HLP oils to DIN 51524, part 2. Brugger- value has to be 30 N/mm2 minimum for general application and 50 N/mm2 for heavily loaded hydraulic equipment and fast cycling machines and/or high dynamic loads, measured in accordance with DIN 51 347-2. See also Document HY30-3248/UK Parker Hydraulic Fluids. Viscosity The normal operating viscosity should range between 16 and 100 mm2/s (cSt). Max. start-up viscosity is 800 mm2/s (cSt). Filtration For maximum pump and system component functionality and life, the system should be protected from contamination by effective filtration. Fluid cleanliness should be in accordance with ISO classification ISO 4406:1999. The quality of filter elements should be in accordance with ISO standards. General hydraulic systems for satisfactory operation: Class 20/18/15, according to ISO 4406:1999 Recommended cleanliness for maximum component life and functionality: Class 18/16/13, according to ISO 4406:1999 Seals Check hydraulic fluid specification for chemical resistance of seal material. Check temperature range of seal material and compare with max. system and ambient temperature. N - Nitrile -40 ... +90 C Note: The highest fluid temperature will be at the drain port of the pump, up to 25 C higher than in the reservoir.
Technical Data
Catalogue HY30-3245/UK
Frame size Max. Displacement [cm3/rev.] Output flow at 1500 rpm [l/min] Nominal pressure pN [bar] Max. pressure pmax at 20% working cycle1) [bar] Case drain pressure, continuous [bar] Case drain pressure, max. peak [bar] Min. Inlet pressure, abs. [bar] Max. Inlet pressure [bar] Input power at 1500 rpm and 350 bar [kW] Max speed at 1 bar, abs, inlet pressure [rpm] Moment of inertia [kgm2] Weight [kg]
Frame size Max. Displacement [cm3/rev.] Output flow at 1500 rpm [l/min] Nominal pressure pN [bar] Max. pressure pmax at 20% working cycle1) [bar] Case drain pressure, continuous [bar] Case drain pressure, max. peak [bar] Min. Inlet pressure, abs. [bar] Max. Inlet pressure [bar] Input power at 1500 rpm and 350 bar [kW] Max speed at 1 bar, abs, inlet pressure [rpm] Moment of inertia [kgm2] Weight [kg] 1) Special control options required.
PV063 PV080 PV092 PV140 PV180 PV270 PV360 3 3 3 4 4 5 5 63 80 92 140 180 270 360 94.5 120 138 270 405 405 540 350 350 350 350 350 350 350 420 420 420 420 420 420 420 0.5 0.5 0.5 0.5 0.5 0.5 0.5 2.0 2.0 2.0 2.0 2.0 2.0 2.0 0.8 0.8 0.8 0.8 0.8 0.8 0.8 16 16 16 16 16 16 16 61.5 78 89.5 136 175 263 350 2800 2500 2300 2400 2200 1800 1750 0.018 0.018 0.018 0.030 0.030 0.098 0.103 59 59 59 90 90 172 180
Ordering Code
Catalogue HY30-3245/UK
PV
axial piston pump variable displacement size and displacement
R 1 K 1 T 1 N
rotation mounting interface thru drive code coupling code seals control
variation
threads code
Code Displacement 016 020 023 028 16 cm/rev 20 cm/rev 23 cm/rev 28 cm/rev
Size 1 1 1 1
Code N V W P
Seals NBR FPM NBR with PTFE shaft seal FPM with PTFE shaft seal
Code R L
1)
Code Coupling for thru drive 1 H Y A B C Single pump, no coupling with coupling 25 x 1.5 x 15, DIN 5480 with coupling SAE A 9T-16/32 DP with coupling SAE - 11T-16/32 DP with coupling SAE B 13T-16/32 DP with coupling SAE B-B 15T-16/32 DP
Code 1 9
2)
Code K L D E
Mounting interface
Shaft
metr. ISO 4-hole flange 100 mm Cylindric, key 3019/2 4-hole flange 100 mm Splined, DIN 5480 SAE ISO 3019/1 4-hole flange SAE B 4-hole flange SAE B-B Cylindric, key Splined, SAE
with adaptor for 2nd pump Y A B G H J SAE AA, 50.8 mm SAE A, 82.55 mm SAE B, 101.6 mm metric, 63 mm metric, 80 mm metric, 100 mm
Code 1 3 7 85)
See dimensions for details 6) to be ordered separately as single part x= Frame size, see displacement.
3) 4) 5)
Drain, gauge and flushing ports All mounting and connecting threads Mounting interface, code K and L only
Ordering Code
Catalogue HY30-3245/UK
Code 0 0 1 1 0 0 M M M R M F M T C 1 W K Z P
Horse power / Torque control Code Nominal HP at 1.500 rpm B C D E G H K Function L C C 1 W K Z Horse power control with pressure control Horse power control with load sensing (single spool) Standard version NG 6 interface top side With unloading function, 24 VDC solenoid Prop.-pilot valve type PVACRE..35 mounted Without integrated pilot valve, NG6 interface, for mounting of accessory code PVAC* 3 kW 4 kW 5.5 kW 7.5 kW 11 kW 15 kW 18.5 kW Nominal torque 20 Nm 25 Nm 35 Nm 50 Nm 71 Nm 97 Nm 120 Nm
Control variation
Control option Proportional displacement control, no pressure compensation Proportional displacement control, with pressure compensation
Control variation R pilot operated pressure control, open NG6 interface K pilot operated pressure control, proportional pilot valve type PVACRE..35 mounted M pilot operated pressure control, pressure sensor and proportional pilot valve type PVACRE..35 mounted for pressure control and/or power control
Ordering Code
Catalogue HY30-3245/UK
PV
axial piston pump variable displacement size and displacement
R 1 K 1 T 1 N
rotation mounting interface thru drive code coupling code seals control
variation
threads code
Size 2 2 2
Code N V W P
Seals NBR FPM NBR with PTFE shaft seal FPM with PTFE shaft seal
Code 1 9
2)
1 H J Y A B C D
Single pump, no coupling with coupling 25 x 1.5 x 15, DIN 5480 with coupling 32 x 1.5 x 20, DIN 5480 with coupling SAE A 9T-16/32 DP with coupling SAE - 11T-16/32 DP with coupling SAE B 13T-16/32 DP with coupling SAE B-B 15T-16/32 DP with coupling SAE C 14T-12/24 DP
requires Kxxxx number Code Thru drive option Mounting interface Shaft No adaptor for 2nd pump T
Single pump prepared for thru drive
Code K L D E
metr. ISO 4-hole flange 125 mm Cylindric, key 3019/2 4-hole flange 125 mm Splined, DIN 5480 SAE ISO 3019/1 4-hole flange SAE C 4-hole flange SAE C Cylindric, key Splined, SAE
with adaptor for 2nd pump A B C G H J K SAE A, 82.55 mm SAE B, 101.6 mm SAE C, 127 mm metric, 63 mm metric, 80 mm metric, 100 mm metric, 125 mm
Code 1 3 7 85)
3) 4) 5)
Drain, gauge and flushing ports All mounting and connecting threads Mounting interface, code K and L only
See dimensions for details 6) to be ordered separately as single part x= Frame size, see displacement.
Ordering Code
Catalogue HY30-3245/UK
Code 0 0 1 1 0 0 M M M R M F M T C 1 W K Z P
Horse power / Torque control Code Nominal HP at 1.500 rpm D E G H K M S 5.5 kW 7.5 kW 11 kW 15 kW 18.5 kW 22 kW 30 kW Nominal torque 35 Nm 50 Nm 71 Nm 97 Nm 120 Nm 142 Nm 195 Nm
Function L Horse power control with pressure control C Horse power control with load sensing (single spool) Control variation C 1 W K Z Standard version NG 6 interface top side With unloading function, 24 VDC solenoid Prop.-pilot valve type PVACRE..35 mounted Without integrated pilot valve, NG6 interface, for mounting of accessory code PVAC*
Control option Proportional displacement control, no pressure compensation Proportional displacement control, with pressure compensation
Control variation R pilot operated pressure control, open NG6 interface K pilot operated pressure control, proportional pilot valve type PVACRE..35 mounted M pilot operated pressure control, pressure sensor and proportional pilot valve type PVACRE..35 mounted for pressure control and/or power control
Ordering Code
Catalogue HY30-3245/UK
PV
axial piston pump variable displacement high pressure version size and displacement
R 1 K 1 T 1 N
rotation mounting interface thru drive code coupling code seals compensator
variation
threads code
Size 3 3 3
Code N V W P
Seals NBR FPM NBR with PTFE shaft seal FPM with PTFE shaft seal
Code R L
1)
Code Coupling for thru drive 1 H J K Y A B C D E F Single pump, no coupling with coupling 25 x 1.5 x 15, DIN 5480 with coupling 32 x 1.5 x 20, DIN 5480 with coupling 40 x 1.5 x 25, DIN 5480 with coupling SAE A 9T-16/32 DP with coupling SAE - 11T-16/32 DP with coupling SAE B 13T-16/32 DP with coupling SAE B-B 15T-16/32 DP with coupling SAE C 14T-12/24 DP with coupling SAE C - C with coupling SAE D, E
as single part 6) MK-PVBGxK01 MK-PVBGxK02 MK-PVBGxK03 MK-PVBGxK11 MK-PVBGxK12 MK-PVBGxK13 MK-PVBGxK14 MK-PVBGxK15 MK-PVBGxK16 MK-PVBGxK17
Code 1 9
2)
Code K L D E
Mounting interface
metr. ISO 4-hole flange 160 mm Cylindric, key 3019/2 4-hole flange 160 mm Splined, DIN 5480 SAE ISO 3019/1 4-hole flange SAE D 4-hole flange SAE D Cylindric, key Splined, SAE
with adaptor for 2nd pump Threads4) metric UNC metr. M14 UNC metric A B C D G H J K L SAE A, 82.55 mm SAE B, 101.6 mm SAE C, 127 mm SAE D, 152,4 mm metric, 63 mm metric, 80 mm metric, 100 mm metric, 125 mm metric, 160 mm
as single part 6) MK-PVBGxAMN MK-PVBGxBMN MK-PVBGxCMN MK-PVBGxDMN MK-PVBGxGMN MK-PVBGxHMN MK-PVBGxJMN MK-PVBGxKMN MK-PVBGxLMN
Code
Port3)
Drain, gauge and flushing ports All mounting and connecting threads For PV063-PV092 only: pressure port 1 1/4" with 4 x M14 instead of 4 x M12
See dimensions for details 6) to be ordered separately as single part x= Frame size, see displacement.
10
Ordering Code
Catalogue HY30-3245/UK
Code 0 0 1 1 0 0 M M M R M F M T C 1 W K Z P
Horse power / Torque control Code Nominal HP at 1.500 rpm G H K M S T U W Function L C C 1 W K Z Horse power control with pressure control Horse power control with load sensing (single spool) Standard version NG 6 interface top side With unloading function, 24 VDC solenoid Prop.-pilot valve type PVACRE..35 mounted Without integrated pilot valve, NG6 interface, for mounting of accessory code PVAC* 11 kW 15 kW 18.5 kW 22kW 30 kW 37 kW 45 kW 55 kW Nominal torque 71 Nm 97 Nm 120 Nm 142 Nm 195 Nm 240 Nm 290 Nm 355 Nm
Control variation
Control option Proportional displacement control, no pressure compensation Proportional displacement control, with pressure compensation
Control variation R pilot operated pressure control, open NG6 interface K pilot operated pressure control, proportional pilot valve type PVACRE..35 mounted M pilot operated pressure control, pressure sensor and proportional pilot valve type PVACRE..35 mounted for pressure control and/or power control
11
Ordering Code
Catalogue HY30-3245/UK
PV
axial piston pump variable displacement size and displacement
R 1 K 1 T 1 N
rotation mounting interface thru drive code coupling code seals control
variation
threads code
Code Code Displacement 140 180 140 cm/rev 180 cm/rev Size 4 4 N V W P
Seals NBR FPM NBR with PTFE shaft seal FPM with PTFE shaft seal
as single part 7) MK-PVBGxK01 MK-PVBGxK02 MK-PVBGxK03 MK-PVBGxK04 MK-PVBGxK11 MK-PVBGxK12 MK-PVBGxK13 MK-PVBGxK14 MK-PVBGxK15 MK-PVBGxK16 MK-PVBGxK17 MK-PVBGxK18
Rotation
1)
Code 1 9
2)
1 H J K L Y A B C D E F G
Single pump, no coupling with coupling 25 x 1.5 x 15, DIN 5480 with coupling 32 x 1.5 x 20, DIN 5480 with coupling 40 x 1.5 x 25, DIN 5480 with coupling 50 x 2 x 24, DIN 5480 with coupling SAE A 9T-16/32 DP with coupling SAE - 11T-16/32 DP with coupling SAE B 13T-16/32 DP with coupling SAE B-B 15T-16/32 DP with coupling SAE C 14T-12/24 DP with coupling SAE C - C with coupling SAE D, E with coupling SAE F
Code K L D E F G Code
metr. ISO 4-hole flange 160 mm Cylindric, key 3019/2 4-hole flange 160 mm Splined, DIN 5480 SAE ISO 3019/1 4-hole flange SAE D 4-hole flange SAE D-F 4-hole flange SAE D 4-hole flange SAE D Port3) Threads4) metric UNC metr. M14 UNC metric Cylindric, key Splined, SAE Cylindric, key Splined, SAE Code Thru drive option No adaptor for 2nd pump T
Single pump prepared for thru drive
with adaptor for 2nd pump A B C D H J K L SAE A, 82.55 mm SAE B, 101.6 mm SAE C, 127 mm SAE D, 152.4 mm metric, 80 mm metric, 100 mm metric, 125 mm metric, 160 mm
as single part 7) MK-PVBGxAMN MK-PVBGxBMN MK-PVBGxCMN MK-PVBGxDMN MK-PVBGxHMN MK-PVBGxJMN MK-PVBGxKMN MK-PVBGxLMN
Drain, gauge and flushing ports All mounting and connecting threads Pressure port 1 1/4" with 4 x M14 instead of 4 x M12 Mounting interface, code K and L only
See dimensions for details 7) to be ordered separately as single part x= Frame size, see displacement.
12
Ordering Code
Catalogue HY30-3245/UK
Code 0 0 1 1 0 0 M M M R M F M T C 1 W K Z P
Horse power / Torque control Code Nominal HP at 1.500 rpm K M S T U W Y Z 2 Function L C C 1 W K Z Horse power control with pressure control Horse power control with load sensing (single spool) Standard version NG 6 interface top side With unloading function, 24 VDC solenoid Prop.-pilot valve type PVACRE..35 mounted Without integrated pilot valve, NG6 interface, for mounting of accessory code PVAC* 18.5 kW 22 kW 30 kW 37 kW 45 kW 55 kW 75 kW 90 kW 110 kW Nominal torque 120 Nm 142 Nm 195 Nm 240 Nm 290 Nm 355 Nm 485 Nm 585 Nm 715 Nm
Control variation
Control option Proportional displacement control, no pressure compensation Proportional displacement control, with pressure compensation
Control variation R pilot operated pressure control, open NG6 interface K pilot operated pressure control, proportional pilot valve type PVACRE..35 mounted M pilot operated pressure control, pressure sensor and proportional pilot valve type PVACRE..35 mounted for pressure control and/or power control
13
Ordering Code
Catalogue HY30-3245/UK
PV
axial piston pump variable displacement high pressure version size and displacement
R 1 K 1 T 1 N
rotation mounting interface thru drive code coupling code seals compensator
variation
threads code
Seals NBR FPM NBR with PTFE shaft seal FPM with PTFE shaft seal
Code R L
1)
Code Coupling for thru drive 1 H J K L M Y A B C D E F Single pump, no coupling with coupling 25 x 1.5 x 15, DIN 5480 with coupling 32 x 1.5 x 20, DIN 5480 with coupling 40 x 1.5 x 25, DIN 5480 with coupling 50 x 2 x 24, DIN 5480 with coupling 60 x 2 x 28, DIN 5480 with coupling SAE A 9T-16/32 DP with coupling SAE - 11T-16/32 DP with coupling SAE B 13T-16/32 DP with coupling SAE B-B 15T-16/32 DP with coupling SAE C 14T-12/24 DP with coupling SAE C - C with coupling SAE D, E
as single part 6) MK-PVBGxK01 MK-PVBGxK02 MK-PVBGxK03 MK-PVBGxK04 MK-PVBGxK05 MK-PVBGxK11 MK-PVBGxK12 MK-PVBGxK13 MK-PVBGxK14 MK-PVBGxK15 MK-PVBGxK16 MK-PVBGxK17
Code 1 9
2)
Code K L D E
Mounting interface
metr. ISO 4-hole flange 200 mm Cylindric, key 3019/2 4-hole flange 200 mm Splined, DIN 5480 SAE ISO 3019/1 4-hole flange SAE E 4-hole flange SAE E-F Cylindric, key Splined, SAE
with adaptor for 2nd pump Threads5) metric UNC UNC metric A B C D E H J K L M SAE A, 82.55 mm SAE B, 101.6 mm SAE C, 127 mm SAE D, 152,4 mm SAE E, 165,1 mm metric, 80 mm metric, 100 mm metric, 125 mm metric, 160 mm metric, 200 mm
as single part 6) MK-PVBGxAMN MK-PVBGxBMN MK-PVBGxCMN MK-PVBGxDMN MK-PVBGxEMN MK-PVBGxHMN MK-PVBGxJMN MK-PVBGxKMN MK-PVBGxLMN MK-PVBGxMMN
Code 1 3 7 8
4) 5)
Drain, gauge and flushing ports All mounting and connecting threads
See dimensions for details 6) to be ordered separately as single part x= Frame size, see displacement.
14
Ordering Code
Catalogue HY30-3245/UK
Code 0 0 1 1 0 0 M M M R M F M T C 1 W K Z P
Displacem. 270
Horse power / Torque control Code Nominal HP at 1.500 rpm T U W Y Z 2 3 Function L C C 1 W K Z Horse power control with pressure control Horse power control with load sensing (single spool) Standard version NG 6 interface top side With unloading function, 24 VDC solenoid Prop.-pilot valve type PVACRE..35 mounted Without integrated pilot valve, NG6 interface, for mounting of accessory code PVAC* 37 kW 45 kW 55 kW 75 kW 90 kW 110 kW 132 kW Nominal torque 240 Nm 290 Nm 350 Nm 480 Nm 580 Nm 700 Nm 840 Nm
Control variation
Control option Proportional displacement control, no pressure compensation Proportional displacement control, with pressure compensation
Control variation R pilot operated pressure control, open NG6 interface K pilot operated pressure control, proportional pilot valve type PVACRE..35 mounted M pilot operated pressure control, pressure sensor and proportional pilot valve type PVACRE..35 mounted for pressure control and/or power control
15
Ordering Code
Catalogue HY30-3245/UK
PV
axial piston pump variable displacement size and displacement
R 1 K 1 T 1 N
rotation mounting interface thru drive code coupling code seals control
variation
threads code
Size 5
Code N V
Code Coupling for thru drive 1 H J K L M P Y A B C D E F G Single pump, no coupling with coupling 25 x 1.5 x 15, DIN 5480 with coupling 32 x 1.5 x 20, DIN 5480 with coupling 40 x 1.5 x 25, DIN 5480 with coupling 50 x 2 x 24, DIN 5480 with coupling 60 x 2 x 28, DIN 5480 with coupling 70 x 3 x 22, DIN 5480 with coupling SAE A 9T-16/32 DP with coupling SAE - 11T-16/32 DP with coupling SAE B 13T-16/32 DP with coupling SAE B-B 15T-16/32 DP with coupling SAE C 14T-12/24 DP with coupling SAE C - C with coupling SAE D, E with coupling SAE F
as single part 6) MK-PVBGxK01 MK-PVBGxK02 MK-PVBGxK03 MK-PVBGxK04 MK-PVBGxK05 MK-PVBGxK06 MK-PVBGxK11 MK-PVBGxK12 MK-PVBGxK13 MK-PVBGxK14 MK-PVBGxK15 MK-PVBGxK16 MK-PVBGxK17 MK-PVBGxK18
Code R
1)
Rotation 1) Clockwise
Code 1 9
2)
requires Kxxxx number Mounting interface Shaft Code Thru drive option No adaptor for 2nd pump T
Single pump prepared for thru drive
Code K L R T D E
4-hole flange 250 mm Cylindric, key metr. ISO 4-hole flange 250 mm Splined, DIN 5480 3019/2 SAE ISO 3019/1 Port3) BSPP UNF 4-hole flange 224 mm Cylindric, key 4-hole flange 224 mm Splined, DIN 5480 4-hole flange SAE E 4-hole flange SAE E Cylindric, key Splined, SAE
with adaptor for 2nd pump A B C D E H J K L M SAE A, 82.55 mm SAE B, 101.6 mm SAE C, 127 mm SAE D, 152.4 mm SAE E, 165.1 mm metric, 80 mm metric, 100 mm metric, 125 mm metric, 160 mm metric, 200 mm
as single part 6) MK-PVBGxAMN MK-PVBGxBMN MK-PVBGxCMN MK-PVBGxDMN MK-PVBGxEMN MK-PVBGxHMN MK-PVBGxJMN MK-PVBGxKMN MK-PVBGxLMN MK-PVBGxMMN
Code 1 3
3) 4)
Drain, gauge and flushing ports All mounting and connecting threads
See dimensions for details 6) to be ordered separately as single part x= Frame size, see displacement.
16
Ordering Code
Catalogue HY30-3245/UK
Code 0 0 1 1 0 0 M M M R M F M T C 1 W K Z P
Displacem. 360
Horse power / Torque control Code Nominal HP at 1.500 rpm U W Y Z 2 3 4 5 6 Function L C C 1 W K Z Horse power control with pressure control Horse power control with load sensing (single spool) Standard version NG 6 interface top side With unloading function, 24 VDC solenoid Prop.-pilot valve type PVACRE..35 mounted Without integrated pilot valve, NG6 interface, for mounting of accessory code PVAC* 45 kW 55 kW 75 kW 90 kW 110 kW 132 kW 160 kW 180 kW 200 kW Nominal torque 290 Nm 350 Nm 480 Nm 580 Nm 700 Nm 840 Nm 1020 Nm 1150 Nm 1280 Nm
Control variation
Control option Proportional displacement control, no pressure compensation Proportional displacement control, with pressure compensation
Control variation R pilot operated pressure control, open NG6 interface K pilot operated pressure control, proportional pilot valve type PVACRE..35 mounted M pilot operated pressure control, pressure sensor and proportional pilot valve type PVACRE..35 mounted for pressure control and/or power control
17
Pressure Controls
Catalogue HY30-3245/UK
MP1
P P
A A
T T
Displacement [%]
Response times of the pump are collected from a circuit as below by measuring the pumps swash angle movement at different pressures.
On/Off valve
t on stroke
PV360
Time on-stroke [ms] against against 50 bar 350 bar 520 180
Time de-stroke [ms] zero stroke zero stroke 50 bar 350 bar 120 82 15 to 350 bar 50 bar 10 to 40 bar 15 bar Max 8.0 l/min
Pressure adjustment range Factory setting pressure Differential pressure adjustment range Factory setting differential pressure Control oil consumption
18
Pressure Controls
Catalogue HY30-3245/UK
P T
P T
P T
P T
19
Catalogue HY30-3245/UK
Control option MRC The remote pressure control adjusts the pump displacement according to the actual need of flow in the system in order to keep the pressure constant at a level given by a remotely installed pilot valve. Control schematics
PR
MP1
P P
A A
T T
Displacement [%]
Response times of the pump are collected from a circuit as below by measuring the pumps swash angle movement at different pressures.
On/Off valve
t on stroke
PV360
Time on-stroke [ms] against against 50 bar 350 bar 520 180
Time de-stroke [ms] zero stroke zero stroke 50 bar 350 bar 120 82 15 to 350 bar 50 bar 10 to 40 bar 15 bar Max 8.0 l/min
Pressure adjustment range Factory setting pressure Differential pressure adjustment range Factory setting differential pressure Control oil consumption
20
Catalogue HY30-3245/UK
P MP1 P
P P A A T T
PR
P T
T T
PR
P
T T
P
P P A A T T
21
Catalogue HY30-3245/UK
Control option MFC The pilot pressure of the load sensing control is taken from a load sensing port in the hydraulic system. It is used to match pump flow to system demands. Control schematics
PF
MP1
P P
A A
T T
Displacement [%]
Response times of the pump are collected from a circuit as below by measuring the pumps swash angle movement at different pressures.
Load valve
t on stroke
PV360
Time on-stroke [ms] stand-by stand-by to 50 bar to 350 bar 500 690
Time de-stroke [ms] 50 bar to 350 bar to stand-by stand-by 830 50 15 to 350 bar 50 bar 10 to 40 bar 10 bar Max 8.0 l/min
Pressure adjustment range Factory setting pressure Differential pressure adjustment range Factory setting differential pressure Control oil consumption
22
Catalogue HY30-3245/UK
PF
P MP1 P
P P A A T T
PF
P
T T
PF
P
T T
P
P P A A T T
23
Catalogue HY30-3245/UK
Control option MTP The pilot pressure of the load sensing control is taken from a load sensing port in the hydraulic system. It is used to match pump flow to system demands. With the 2 spool control the interaction of the two control functions is avoided by using two separate control valves for flow and pressure compensation. Control schematics
PF
MP1 P
P P
A A
T T
Displacement [%]
Response times of the pump are collected from a circuit as below by measuring the pumps swash angle movement at different pressures.
Load valve
t on stroke
PV360
Time on-stroke [ms] stand-by stand-by to 50 bar to 350 bar 920 670
Time de-stroke [ms] 50 bar to 350 bar to stand-by stand-by 1000 170 15 to 350 bar 50 bar 10 to 40 bar 10 bar 15 bar Max 8.0 l/min
Pressure adjustment range Factory setting pressure Differential pressure adjustment range Factory setting differential pressure load sensing Factory setting differential pressure, pressure control Control oil consumption
24
Catalogue HY30-3245/UK
MP1 P
P P
A A
T T
P P
A A
T T
PF
25
Catalogue HY30-3245/UK
Control option *LC The horse power control type *L* provides the benefit of the pressure control, plus the ability to limit the input power the pump will draw. These controls are beneficial when the power available from the prime mover for the hydraulics is limited or the application power demand has both high flow/low pressure and low flow/high pressure duty cycles. Control schematics
MP1
P P
A A
L L
T T
Displacement [%]
Response times of the pump are collected from a circuit as below by measuring the pumps swash angle movement at different pressures.
Load valve
t on stroke
PV360
Time de-stroke [ms] zero stroke zero stroke 50 bar 350 bar 100 100 15 to 350 bar 350 bar 10 to 40 bar 15 bar Max 8.0 l/min
Pressure adjustment range Factory setting pressure Differential pressure adjustment range Factory setting differential pressure Control oil consumption
26
Catalogue HY30-3245/UK
P MP1 P T
P P A A L L T T
P T
P T
This allows a variation of the pump compensating pressure between 20 and 350 bar by an electrical signal.
P T
27
Catalogue HY30-3245/UK
MP1
P P
A A
L L
T T
Displacement [%]
Response times of the pump are collected from a circuit as below by measuring the pumps swash angle movement at different pressures.
Load valve
t on stroke
PV360
Time de-stroke [ms] 50 bar to 350 bar to stand-by stand-by 100 100 15 to 350 bar 350 bar 10 to 40 bar 15 bar Max 8.0 l/min
Pressure adjustment range Factory setting pressure Differential pressure adjustment range Factory setting differential pressure Control oil consumption
28
Catalogue HY30-3245/UK
P MP1 P T
P P A A L L T T
PF
P T
L L T T
PF
P T
L L T T
P T
P P A A L L T T
29
Catalogue HY30-3245/UK
Performance Curves
40 35 30 25 20 15
E= 7.
H=
G= 11 kW
45
60
50
3 S= 0 kW
40
K= 18
15
.5 18 K= kW
M
.5
=2
2k
kW
30
G= 11
kW
20
10 5 0
B=
C=
D=
4 kW
5.5
kW
D=
10
E=
3k
5.5
7.5
kW
15 H= kW
5 kW
kW
kW
50
100
150
200
250
Pressure p [bar]
300
350
50
100
150
200
250
Pressure p [bar]
300
350
140
PV140
W
U=
kW
=5
Z=
75
kW
90
kW
kW K= M=2 K= 18 2 18 H= .,5 k kW 5 15 kW W G= kW 11 kW
30
45
kW
kW
=5 5
U= 45
kW M kW K= =22 18 k ,5 W kW
30
T=
kW
37
kW
350
Pressure p [bar]
50
100
150
200
250
300
350
Pressure p [bar]
30
Performance Curves
Catalogue HY30-3245/UK
300 270 240 210 180 150 120 90 60 30 0 0 50 100 150 200 250
W =5
PV180
PV270
Z=
75 Y=
2=
90
11
kW
kW
3=
S= T=3 kW 30 7 k M kW W =2 2 kW
U=
45
kW
Y=
Z=
75
90
11 0
13
W= U= 55 k T= 45 k W 37 W kW
kW
kW
kW kW
kW
300
350
Pressure p [bar]
50
100
150
200
250
300
350
Pressure p [bar]
550 500 450 400 350 300 250 200 150 100 50 0
0 50 100 150 200 250 300 350 Pressure p [bar]
6= 2 5= 00 4= 18 kW 0 16 0 k kW 3= W 13 2k 2= 11 W 0k Z= W 90 kW Y= 75 kW W= 55 U= 45 kW kW
PV360
: : : : :
n = 1500 rev/min t = 50 C HLP, ISO VG46 = 46 mm2/s at 40 C Maximum 350 bar, depending on HP level
31
Catalogue HY30-3245/UK
Control option FPV The proportional displacement control allows the adjustment of the pumps output flow with an electrical input signal. The actual displacement of the pump is monitored by an LVDT and compared with the commanded displacement in an electronic control module PQDXXA-Z00. The command is given as an electrical input signal (0 - 10 V) from the supervising machine control or a potentiometer. Version FPV of the proportional control does not provide a pressure compensation. The hydraulic circuit must be protected by a pressure relief valve. Control schematics
MP1 P
P P
A A
T T
UQ
= FPV included
Displacement [%]
Response times of the pump are collected from a circuit as below by measuring the pumps swash angle movement at different pressures.
Load valve
t on stroke
PV360
Time on-stroke [ms] stand-by stand-by to 50 bar to 350 bar 180 100
Time de-stroke [ms] 50 bar to 350 bar to stand-by stand-by 330 240 25 to 350 bar 50 bar 10 to 40 bar 15 bar Max 8.0 l/min
Pressure adjustment range * Factory setting pressure * Differential pressure adjustment range * Factory setting differential pressure * Control oil consumption
Internal pilot pressure required to control the pump FPV UPR UPK UPM
Catalogue HY30-3245/UK
T MP1 P
P P A A T T
UQ UP
p = UPM included
33
Catalogue HY30-3245/UK
vol. efficiency
overall efficiency
20
80
15
12
60
10
inp
5 4
ut
ra we po
tf
ull
w flo
40
20
dhead
300 Pressure [bar] 0
PV020
Output flow [l/min] Input power [kW]
30 25 outp ut flow, vol. ef 20
25
20
100
overall efficiency
80
ficiency
14 12 10 8 6 4
dead head full flow
24
18
15
60
12
10
inp
6 5
p ut
er ow
f at
ull
w flo
40
20
input power
0 0 0 100
at deadhead
200 300 Pressure [bar] 0
Pressure [bar]
PV023
Efficiency [%] (overall, volymetric) Input power [kW] Output flow [l/min]
40 25 vol. efficiency 20 100
PV028
overall efficiency output flow 80
Output flow [l/min]
vol. efficiency
32
40
20
output flow
fficienc y
80
i
8 5
20
10
in pu tp ow e
ra tf
ul
16
10
u np
er ow p
at
overall e
24
15
l fl ul
ow
60
30
15
60
40
l fl
20
10
40
20
input power
0 0 0 100
at deadhead
200 300 Pressure [bar] 0 0 0 0
ad
0
34
50
25
100
ow
Catalogue HY30-3245/UK
40
overall efficiency
80
30
24
60
20
16
inp
10 8
ut
a er ow p
tf
ow ll fl
40
20
input powe
0 0 0 100
r at
deadhead
0 300 350 Pressure [bar]
200
50
40
vol. efficiency
100
PV040
Output flow [l/min] Input power [kW]
60 40
48
32
overall efficiency
80
100
ciency
36
24
60
24
16
inp
12 8
p ut
e ow
ra
u tf
ll fl
ow
40
20
input power
0 0 0 100
at deadhead
200 300 350 Pressure [bar] 0
0 0
100
200
Pressure [bar]
300
PV046
Output flow [l/min] Input power [kW]
vol. efficiency
overall efficiency
80
64
40
output flow
48
30
32
20
in
16 10
pu
tp
er ow
at
l fu
l fl
ow
60
40
20
0 0
input power
100
at deadhead
200 300 350 Pressure [bar] 0
80
50
100
35
Catalogue HY30-3245/UK
output flow
56
80
overall efficiency
80
60
42
40
28
in
20 14
pu
r we po
at
l fl ul
ow
60
40
20
PV080
Output flow [l/min] Input power [kW]
120 80
output flow, vo
l. efficiency
100
100
70
vol. efficiency
100
overall efficiency
64 80
96
12
72
48
48
32
in
pu
a er ow p
u tf
ll fl
ow
60
40
8
dead head
24
16
20
d
0
PV092
Output flow [l/min] Input power [kW]
150 100
output flow
100
full flow
0 0
100
200
Pressure [bar]
300
120
80
80
90
60
60
40
p in
r we po t
at
l fu
l fl
ow
60
40
30
20
20
er input pow
0 0 0 100
ad at deadhe
300 Pressure [bar] 0
200
36
Catalogue HY30-3245/UK
overall efficiency
120
200
output flow
80
150
90
100
60
in
50 30
pu
r we po
u tf
ll fl
ow
60
40
20
PV180
Output flow [l/min] Input power [kW]
300 175
250
150
100
fficienc y
240
140
output flow
80
180
overall e
105
120
70
in
pu
r we po t
f at
l ul
w flo
vol. efficiency
100
60
12
dead head
40
60
35
20
ad
0
full flow
0 0
100
200
Pressure [bar]
300
37
Catalogue HY30-3245/UK
500
250
400
200
output flow
80
24
16
ow er
at
fu l
300
150
l fl
ow
dead head
60
100
50
in
200
100
40
pu
tp
20
full flow
input power at
0 100
deadhead
300 Pressure [bar] 0
0 0
100
200
200
Pressure [bar]
300
Efficiency and case drain flows PV270 The efficiency and power graphs are measured at an input speed of n = 1500 rpm, a temperature of 50 C and a fluid viscosity of 30 mm2/s. Case drain flow and compensator control flow leave via the drain port of the pump. To the values shown are to be added 1 to 1.2 l/min , if at pilot operated compensators (codes FR*, FF*, FT*, power compensator and p-Qcontrol) the control flow of the pressure pilot valve also goes through the pump. Please note: The values shown below are only valid for static operation. Under dynamic conditions and at rapid compensation of the pump the volume displaced by the servo piston also leaves the case drain port. This dynamic control flow can reach up to 120 l/min! Therefore the case drain line is to lead to the reservoir at full size and without restrictions as short and direct as possible.
38
Performance Curves Typical inlet characteristics vs. speed at various percentage displacements Inlet characteristics
Self priming speed [rpm]
1850 1800 1750 1700 1650 1600 1550 1500 0.8
Catalogue HY30-3245/UK
Axial Piston Pump PV 360 Typical drive power at full displacement Input power full stroke
400
1750 rpm
1500 rpm
0.9
1.0
1.1
0 0 25 50 75 100 125 150 175 200 225 250 275 300 325 350
Pressure [bar]
Volumetric
30
90%
1750 rpm
25 20
Overall
80%
15 10 5
1500 rpm
70%
60%
25 50 75 100 125 150 175 200 225 250 275 300 325 350
Pressure [bar]
25
50
75 100 125 150 175 200 225 250 275 300 325 350
Pressure [bar]
32
24
dead head
16
full flow
0 0 100 200
Pressure [bar]
300
360
The curves show typical characteristics measured under following conditions: Fluid: Mineral oil ISO VG 22 at 32 C Inlet pressure 1,0 bar (absolute), measured at inlet port. 39
Parker Hannifin Pump and Motor Division Chemnitz, Germany
Accessories Control
Catalogue HY30-3245/UK
PV
AC
Mounting bolts Threads Seals
35
Adjustment Solenoid Solenoid Nominal acces- pressure sories 350 bar Code Solenoid accessories omit W Seals NBR FPM For function 1P DIN plug socket without plug
Accessories Function For for PV pump controls series Code 1P 1E Function Max. pressure relief 1 pressure, electrical unloading stand by default 2 pressures, electrical selection 2 pressures + stand by electrical selection low pressure default 2 pressures + stand by electrical selection stand by default
Code M S
2P
2E
Code C S M
Mounting bolts For single controls Without bolts For code UP*/MT*
2M
Dimensions PVAC1P*
Adjustment Code S
PVAC1E*
DC solenoid 205 AC solenoid 190
48
PVAC2P*
DC solenoid 205 AC solenoid 190
PVAC2M*/PVAC2E*
48
DC solenoid 241 AC solenoid 211
48
133
133
High pressure Low pressure High pressure Low pressure
40
133
Accessories Control
Schematics PVAC1P*
Catalogue HY30-3245/UK
Schematics PVAC2P*
Schematics PVAC2M*/PVAC2E*
*2M*
41
Catalogue HY30-3245/UK
Technical data
General Nominal size Mounting position Ambient temperature Weight Hydraulic Max. operating pressure Pressure stages Fluid Viscosity, recommended permitted Fluid temperature Filtration Linearity Repeatability Hysteresis DIN NG06 / CETOP03 / NFPA D03 as desired, horizontal mounting preferred [C] -20 ... +70 [kg] 1.8 [bar] Ports P and A up to 420; port T depressurized [bar] 350, 420 Hydraulic oil as per DIN 51524 ... 525 [cSt] / [mm/s] 30 ... 80 [cSt] / [mm/s] 12 ... 380 [C] -20 ... +60 ISO 4406 (1999), 18/16/13 [%] 2.8 [%] <1 [%] 1.5 of pmax [%] 100 ED IP 65 in accordance with EN 60529 (plugged and mounted) [V] 16 (1.3 A max. current) [Ohm] 4 at 20C Connector as per EN 175301-803 PCD00A-400
Electrical Duty ratio Protection class Nominal voltage Coil resistance Solenoid connection Power amplifier, recommended
42
Accessories Control
Ordering code proportional pressure relief valve
Catalogue HY30-3245/UK
PV
Pump series PV
AC
Accessories for controller
RE
Prop. pressure valve Mounting bolts Thread option Seal Nominal pressure
Code Nominal pressure 35 42 Code C S M Mounting bolts/ ports For single controller Without bolts For code UP*/MT* design series 45/46 Code M S Thread option Metric SAE / UNC Code N V Seal NBR FPM 350 bar 420 bar
Dimensions PVACRE*
P MP1 P
P P A A T T
43
Dimensions
Catalogue HY30-3245/UK
view X
max. 212 197.5 10 9.0 Gage port M; G1/4 optional M12x1.5; ISO 6149-1 (thread options 7 and 8) or 7/16-20 UNF (thread option 3)
12 125
170.5
Drain port L2 and L3 (opposite); G1/2 optional M22x2; ISO 6149-1 (thread options 7 and 8) or 7/8-14 UNF (thread option 3)
50.8
OUTLET for metric and SAE version: flage acc. ISO 6162 DN19; PN400 4xM10, 18 deep optional 3/8-16UNC-2B (thread options 3 and 7) 23.8 100h8 30.2 INLET for metric and SAE version: flage acc. ISO 6162 DN32; PN250 43 4xM10, 18 deep optional 7/16-14UNC-2B (thread options 3 and 7)
The pump shown above has mounting option K and thru drive option T (prepared for thru drive)
58.7
Shown is a clockwise rotating pump with standard pressure compensator. Counter clockwise rotating pumps have inlet, outlet and gauge port reversed.
44
Dimensions
Catalogue HY30-3245/UK
13.5
89.9
44.9
44.9 89.9
Mounting option E Splined shaft 15T-16/32 DP, flat root, side fit ANSI B92.1
46
Thru drive: splined shaft 13T-16/32 DP, flat root, side fit
C G E
197.5 (224.5)
B 27 47
45
Dimensions
Catalogue HY30-3245/UK
149 97 16 68
view X
227 max 248
Gage port M; G1/4 optional M12x1,5; ISO 6149-1 (thread options 7 and 8) or 7/16 - 20 UNF (thread option 3)
9 10
99 71 60
14 160
50
185 197
138
Drain ports L2 and L3 (opposite); G3/4 optional M27 x 2: ISO 6149-1 (thread options 7 and 8) or 1 1/16 - 12 UNF (thread option 3)
mounting option K
57.2
OUTLET for metric and SAE version: flange acc. ISO 6162 DN25; PN400 4 x M12, 18 deep optional 7/16-14 UNC-2B (thread options 3 and 7) 27.8 INLET for metric and SAE version: flange acc. ISO 6162 DN38; PN200 4 x M12, 18 deep optional 1/2-13 UNC-2B (thread options 3 and 7)
125 h8
69.9
47
35.7
Shown is a clockwise rotating pump with standard pressure compensator. Counter clockwise rotating pumps have inlet, outlet and gauge port reversed.
46
Catalogue HY30-3245/UK
Dimensions
14
114.5
57.25
8 60 68
127-0.05
12.7 Mounting option E Splined shaft 14T-12/24 DP, flat root, side fit ANSI B92.1
56
C
G
227 K L
D F
47
Dimensions
Catalogue HY30-3245/UK
Max. 133
Gage port M; G1/4, optional M12 x 1.5; ISO 6149-1 (tread option 7 and 8) or 7/16- 20 UNF (tread option 3)
9 10
view X
121
86 78
26
64
187.5
236 252
77.8 50
INLET for metric and SAE version: flange according ISO 6162 DN 51; PN 200 bar 4 x M12, 20 deep optional 1/2 - 13 UNC - 2B (thread options 3 and 7)
42.9
The pump shown above has Mounting option K and through drive variation T (prepared for through drive)
160 h8
31.8
66.6 32
4 x M12, 20 deep optional 1/2 - 13 UNC - 2B (thread options 3 and 7) or thread options 4: 4 x M14, 20 deep OUTLET for metric and SAE version: flange according ISO 6162 DN 32; PN 400 bar
56
48
18
Dimensions
Catalogue HY30-3245/UK
44.45-0.05
49.3-0.05
152.4
12.6 8
82 90
75
152.4-0.05
Mounting option E splined shaft 13T-8/16 DP, flat root, side fit ANSI B92.1
287 L K
49
Dimensions
Catalogue HY30-3245/UK
35
160 h8
35
97
202
20 48 350
9.3
92
145
182 158
Max. 133
200
Gage port M; G1/4, optional M12 x 1.5; ISO 6149-1 (tread option 7 and 8) or 7/16- 20 UNF (tread option 3)
53.5-0.25
283 106
105
146
18
00
Bearing flushing port F; G1/4, optional M12 x 1.5; ISO 6149-1 (tread option 7 and 8) or 7/16 - 20 UNF (tread option 3)
40
88.9
INLET for metric and SAE version: flange according ISO 6162 DN 64; PN 160 bar 4 x M12, 20 deep optional 1/2 - 13 UNC - 2B (thread options 3 and 7)
The pump shown above has Mounting option K and through drive variation T (prepared for through drive)
63
50.8
31.8
4 x M12, 20 deep optional 1/2 - 13 UNC - 2B (thread options 3 and 7) or thread options 4: 78 4 x M14, 22 deep OUTLET for metric and SAE Shown is a clockwise rotating pump with standard pressure control. version: Counter clockwise rotating pump have inlet, outlet and gauge port reversed. flange according ISO 6162 DN 32; PN 400 bar
66.6
32
50
160 h8
Dimensions
Catalogue HY30-3245/UK
56.4 0.13
21
80.8
12.3
8
Shown above is Mounting option D Mounting option E splined shaft 15T-8/16 DP, flat root, side fit ANSI B92.1
91.4 99.4
80.8 161.6
44.45 -0.05
49.3 0.13
Mounting option G splined shaft 13T-8/16 DP, flat root, side fit ANSI B92.1
152.4 -0.05
152.4 -0.05
88
152.4 -0.05
75
75
B 350 (415) 97 65 D F
51
161.6
Dimensions
PV 270 Metric
Catalogue HY30-3245/UK
Mounting interface for horse power pilot or LVDT for displacement feedback
Gage port M; G1/4, optional M12 x 1.5; ISO 6149-1 (tread option 7 and 8) or 7/16- 20 UNF (tread option 3)
176
184
view X
173
128
110
22
250
X
294 378 403
135
Bearing flushing port F; G1/4, optional M12 x 1.5; ISO 6149-1 (tread option 7 and 8) or 7/16 - 20 UNF (tread option 3) The pump shown above has Mounting option K and through drive variation T (prepared for through drive)
120.7
88
INLET for metric and SAE version: flange according ISO 6162 DN 89; PN 35 bar 4 x M16, 30 deep optional 5/8 - 11 UNC - 2B (thread options 3 and 7)
69.8 36.7
80
79.4
38
4 x M16, 30 deep optional 5/8 - 11 UNC - 2B (thread options 3 and 7) OUTLET for metric and SAE version: flange according ISO 6162 DN 38; PN 400 bar
52
200
Dimensions
Catalogue HY30-3245/UK
15.9 89.5
97.5
112.25 224.5
Mounting option E splined shaft 15T-8/16 DP, flat root, side fit ANSI B92.1
88
472.5 531.5
98
D F
53
112.25
224.5
Dimensions
PV 360 Metric
Catalogue HY30-3245/UK
Mounting interface for horse power pilot or LVDT for displacement feedback
176 25 9 115 max. 133 250 Shown with standard pressure control 9 10
60 477 max. 510 Gauge port M; G1/4, optional 7/16- 20 UNF (tread option 3)
view X
26
100 Bearing flushing port L4; G1/4, optional 7/16 - 20 UNF (thread option 3)
377 408
294
The pump shown above has Mounting option K and through drive variation T (prepared for through drive)
79.4
flange according ISO 6162 DN 38; PN 400 bar 1 1/2" 38 4 x M16, 30 deep optional 5/8 - 11 UNC - 2B (thread option 3) 36.5 77.8
24 250h8 (L) resp. 224h8 (T) Thread M20 - 42 deep 80 90 Mounting option L, T, splined shaft W 70 x 3 x 22 x 8f DIN 5480 mounting option R pilot diameter 224 mm
280 224h8
130.2
flange according ISO 6162 DN 102; PN 35 bar 4" 102 4 x M16, 30 deep optional 5/8 - 11 UNC - 2B (thread option 3)
54
Dimensions
Catalogue HY30-3245/UK
78-0.25 69.85-0.05
112.25
165.1-0.05 Thread 5/8-11 UNC-2B 36 deep 92 100 Shown above is Mounting option D 112.25 224.5 Note: The dimensions shown conform to ISO 3019/1 the actual hole dimensions conform to ISO 3019/2 (pitch 315, hole 26, see previous page) and cover ISO 3019/1 dimensions as well. Use washers when assembling pump. 224.5
10 15.6
165.1-0.05 Mounting option E splined shaft W 70x3x22x8f, DIN 5480 90 Output: splined shaft W 50x2x24x9g DIN 5480
B 477 (536) 59 97 D F
55
Control Dimensions
Dimensions standard pressure control, code ...MMC
43.4
Catalogue HY30-3245/UK
P A
L T
45 54
88.5
Pump axis
24
Controls with code ...MM1 have a NG6 / Cetop 3 interface topside (as shown below) Dimensions remote pressure and load sensing control, codes ...MR1, ...MF1
43.4
max. 172
41
P A
L T P
45
69.5
Pump axis All control ports G1/4 Optional 7/16-20 UNF (option 3)
88.5
24
remote control port pP (code ...MRC, ...MR1) resp. LS port pF (code ...MFC, ...MF1)
Controls with code ...MRC and MFC have no topside valve interface (as shown above) Dimensions horse power pilot cartridge, displacement sensor
45
73
37.5
Pump housing
56
Control Dimensions
Catalogue HY30-3245/UK
97
41
Shown in version MRW/MFW, version MMW has no remote control port. Dimensions for controls with proportional pressure pilot valve, codes ...M*K
43.4
pilot valve: PVACREC**35 for codes ...M*K, ** for threads and seals option
130
171
96
Shown in version MRK/MFK, version MMK has no remote control port. Dimensions for horse power compensator *L* and *C* are identical to MM* respectively MF*. 57
Parker Hannifin Pump and Motor Division Chemnitz, Germany
Control Dimensions
Catalogue HY30-3245/UK
Dimensions two spool load sensing control, code ...MT1, ...MTP LS port pF
96 88
110
Pump axis
191
104
80.5
58
29
elbow manifold
Dimensions two spool load sensing control with proportional pressure pilot valve, code ...MTK LS port pF
88 96
110
pilot valve: PVACREM**35 for code ...MTK, ** for threads- and seals soption Pump axis proportional pressure pilot valve pressure control stage
222
105 81 58 29
116
elbow manifold 58
Control Dimensions
Catalogue HY30-3245/UK
95
108
45
pump axis
50
61
96 91
110
pilot valve: PVACREM**35 for code ...UPK, UPM ** for threads- and seals option
110
pressure pilot valve (codes ...UPK, ...UPM only pump axis pressure sensor (code ...UPM only) pressure control stage
222
116 105 81 58 29
elbow manifold
59
Catalogue HY30-3245/UK
Technical data
Mounting style Body material Inflammation class Mounting position Env. temperature range Protection class Weight Duty ratio Supply voltage Rush in current Current consumption Resolution Interface EMC Connctors Cables Max. cable length Snap-on mounting for EN50022 rail Polycarbonate V2...V0 acc. UL 94 any [C] -20...+55 IP 20 acc. DIN 40 050 [g] 160 [%] 100 [V] 18...30VDC, ripple <5% eff. [A] 22 for 0.2 ms [A] < 4 for p/Q control ; < 2 for Q-control [%] 0.025 (power 0.1) RS232C, 9600 baud, 3.5 mm cinch EN 50 081-2, EN 50 082-2 Screw terminals 0.2...2.5 mm, plug in style [mm] Supply and solenoid cables; 1,5 mm2 (AWG16) overall braid shield. Sensor and command signals; 0,5 mm2 (AWG20) overall braid shield [m] 50
For programming the module via PC, an interface cable is needed, please order part number PQDXXA-KABEL (RS232) or PQDXXA-KABEL-USB (USB) separately.
Ordering code
PQD
Digital control module for p/Q control
XX
For all frame sizes series PV
A
Version A
Z00
Option
Programming software The programming of the p/Q control module is done in an easy to learn mode. To select the pump model and size and to set the control paramters the program ProPVplus must be started. This program runs under WINDOWS 95 and higher. The latest version of this software can be downloaded at the following internet address:
www.parker.com/euro_pmd
Features Display and documentation of parameter sets Save ond reload of optimized parameter sets Offers oscilloscope function for easy performance evaluation and optimization Parameter sets for all PVplus pumps are pre-installed in the modules 60
Parker Hannifin Pump and Motor Division Chemnitz, Germany
Catalogue HY30-3245/UK
MK
Mounting kit
PV
Axial piston pump series PV
BG
Size Second pump Thread Seals
Code 1 2 3 4 5
Pump size Pump size 1: PV016 - PV028 Pump size 2: PV032 - PV046 Pump size 3: PV063 - PV092 Pump size 4: PV140 - PV180 Pump size 5: PV270 - PV360 Code T Y A B C D E H J K L M Second pump, SAE Prepared for thru drive option (plugged) SAE AA, diameter 50.8 mm SAE A, diameter 82.55 mm SAE B, diameter 101.6 mm SAE C, diameter 127,mm SAE D, diameter 152.4 mm SAE E, diameter 165.1 mm Second pump, metric Diameter 80 mm Diameter 100 mm Diameter 125 mm Diameter 160 mm Diameter 200 mm
Code N V
Code M S
Kit contains positions 30, 69, 84, 85 and 87, see drawing below.
MK
Mounting kit
PV
Axial piston pump series PV
BG
Size
K
Coupling
Code 1 2 3 4 5
Pump size Pump size 1: PV016 - PV028 Pump size 2: PV032 - PV046 Pump size 3: PV063 - PV092 Pump size 4: PV140 - PV180 Pump size 5: PV270 - PV360
Code 01 02 03 04 05 06
Coupling for metric, splined shaft DIN 5480 N25 x 1.5 x 15 N32 x 1.5 x 20 N40 x 1.5 x 25 N50 x 2 x 24 N60 x 2 x 28 N70 x 3 x 22* Coupling for SAE splined shaft flat root, side fit
SAE, splined
11 12 13 14 15 16 17 18
SAE A, 9T 16/32 SAE-, 11T 16/32 SAE B, 13T 16/32 SAE B-B, 15T 16/32 SAE C, 14T 12/24 SAE C-C, 17T 12/24 SAE D+E, 13T 8/16 SAE F, 15T 8/16 Coupling + adaptor for keyed shaft
metric splined
20 21 22
front pump
second pump
Availability of thru drive flange and coupling please check with ordering code options per each pump size, starting at page 6
61
Catalogue HY30-3245/UK
L1
W1 L2 L3 W2 W3
Moment M = (L1*W1 + L2*W2 + L3*W3 +...) Note: If the calculated moment M exceed the maximum moment in table 1 below, additional pump support is needed Table 1: Maximum Moment and Pump Dimensions
PV016-PV028 Maximum moment Weight W Distance L1 Distance Lp
1)
62
Catalogue HY30-3245/UK
Important notice The max. allowable torque of the individual shaft must not be exceeded. For 2-pump combinations there is no problem because PV series offers 100% thru torque. For 3-pump combinations (and more) the limit torque could be reached or exceeded. Therefore it is necessary to calculate the torque factor and compare it with the allowed torque limit factor in the table. Required: calculated torque factor < torque limit factor
Pump
Shaft D E K L D E K L D E K L D E F G K L D E K L
Torque limit factor 17700 17700 17700 20130 32680 36380 33810 40250 77280 72450 67620 83720 118400 158760 78750 97650 113400 157500 119000 159700 170100 236250
PV016-028
PV032-046
To make the necessary calculations easier and more user friendly it is not required to calculate actual torque requirements in Nm and compare them with the shaft limitations. The table on the right shows limit factors that include material specification, safety factors and conversion factors. The total torque factor is represented by the sum of the individual torque factors of all pumps in the complete pump combination. Total torque factor of the combination = sum of individual torque factors of all pumps The torque factor of each individual pump is calculated by multiplying the max. operating pressure p of the pump (in bar) with the max. displacement Vg of the pump (in cm/rev). Torque factor of any pump = p x Vg
PV063-092
PV140-180
PV270
63
Catalogue HY30-3245/UK
250h8
250h8
Metric key 70 mm Max. input torque 3750 Nm Max. through drive torque 3250 Nm
105 115
80 90
Metric spline W70x3x22x9g DIN5480 Max. input torque 8100 Nm Max. through drive torque 3250 Nm
224h8
224h8
Metric key 70 mm Max. input torque 3750 Nm Max. through drive torque 3250 Nm
105 115
80 90
Metric spline W70x3x22x9g DIN5480 Max. input torque 8100 Nm Max. through drive torque 3250 Nm
165.1-0.05
165.1-0.05
SAE key 69,85 mm Max. input torque 4750 Nm Max. through drive torque 3250 Nm
92 100
80 90
Metric spline W70x3x22x9g DIN5480 Max. input torque 8100 Nm Max. through drive torque 3250 Nm
64
Catalogue HY30-3245/UK
Notes
65
Catalogue HY30-3245/UK
Notes
66
Catalogue HY30-3245/UK
Offer of Sale
Please contact your Parker representation for a detailed Offer of Sale.
67
Parker Worldwide
Europe, Middle East, Africa
AE United Arab Emirates, Dubai Tel: +971 4 8127100 parker.me@parker.com AT Austria, Wiener Neustadt Tel: +43 (0)2622 23501-0 parker.austria@parker.com AT Eastern Europe, Wiener Neustadt Tel: +43 (0)2622 23501 900 parker.easteurope@parker.com AZ Azerbaijan, Baku Tel: +994 50 2233 458 parker.azerbaijan@parker.com BE/LU Belgium, Nivelles Tel: +32 (0)67 280 900 parker.belgium@parker.com BY Belarus, Minsk Tel: +375 17 209 9399 parker.belarus@parker.com CH Switzerland, Etoy Tel: +41 (0)21 821 87 00 parker.switzerland@parker.com CZ Czech Republic, Klecany Tel: +420 284 083 111 parker.czechrepublic@parker.com DE Germany, Kaarst Tel: +49 (0)2131 4016 0 parker.germany@parker.com DK Denmark, Ballerup Tel: +45 43 56 04 00 parker.denmark@parker.com ES Spain, Madrid Tel: +34 902 330 001 parker.spain@parker.com FI Finland, Vantaa Tel: +358 (0)20 753 2500 parker.finland@parker.com FR France, Contamine s/Arve Tel: +33 (0)4 50 25 80 25 parker.france@parker.com GR Greece, Athens Tel: +30 210 933 6450 parker.greece@parker.com HU Hungary, Budapest Tel: +36 1 220 4155 parker.hungary@parker.com IE Ireland, Dublin Tel: +353 (0)1 466 6370 parker.ireland@parker.com IT Italy, Corsico (MI) Tel: +39 02 45 19 21 parker.italy@parker.com KZ Kazakhstan, Almaty Tel: +7 7272 505 800 parker.easteurope@parker.com NL The Netherlands, Oldenzaal Tel: +31 (0)541 585 000 parker.nl@parker.com NO Norway, Asker Tel: +47 66 75 34 00 parker.norway@parker.com PL Poland, Warsaw Tel: +48 (0)22 573 24 00 parker.poland@parker.com PT Portugal, Leca da Palmeira Tel: +351 22 999 7360 parker.portugal@parker.com RO Romania, Bucharest Tel: +40 21 252 1382 parker.romania@parker.com RU Russia, Moscow Tel: +7 495 645-2156 parker.russia@parker.com SE Sweden, Spnga Tel: +46 (0)8 59 79 50 00 parker.sweden@parker.com SK Slovakia, Bansk Bystrica Tel: +421 484 162 252 parker.slovakia@parker.com SL Slovenia, Novo Mesto Tel: +386 7 337 6650 parker.slovenia@parker.com TR Turkey, Istanbul Tel: +90 216 4997081 parker.turkey@parker.com UA Ukraine, Kiev Tel +380 44 494 2731 parker.ukraine@parker.com UK United Kingdom, Warwick Tel: +44 (0)1926 317 878 parker.uk@parker.com ZA South Africa, Kempton Park Tel: +27 (0)11 961 0700 parker.southafrica@parker.com
North America
CA Canada, Milton, Ontario Tel: +1 905 693 3000 US USA, Cleveland (industrial) Tel: +1 216 896 3000 US USA, Elk Grove Village (mobile) Tel: +1 847 258 6200
Asia Pacific
AU Australia, Castle Hill Tel: +61 (0)2-9634 7777 CN China, Shanghai Tel: +86 21 2899 5000 HK Hong Kong Tel: +852 2428 8008 IN India, Mumbai Tel: +91 22 6513 7081-85 JP Japan, Fujisawa Tel: +81 (0)4 6635 3050 KR South Korea, Seoul Tel: +82 2 559 0400 MY Malaysia, Shah Alam Tel: +60 3 7849 0800 NZ New Zealand, Mt Wellington Tel: +64 9 574 1744 SG Singapore Tel: +65 6887 6300 TH Thailand, Bangkok Tel: +662 717 8140 TW Taiwan, Taipei Tel: +886 2 2298 8987
South America
AR Argentina, Buenos Aires Tel: +54 3327 44 4129 BR Brazil, Sao Jose dos Campos Tel: +55 12 4009 3500
Ed. 2010-11-30
CL Chile, Santiago Tel: +56 2 623 1216 MX Mexico, Apodaca Tel: +52 81 8156 6000 VE Venezuela, Caracas Tel: +58 212 238 5422
EMEA Product Information Centre Free phone: 00 800 27 27 5374 (from AT, BE, CH, CZ, DE, DK, EE, ES, FI, FR, IE, IL, IS, IT, LU, MT, NL, NO, PL, PT, RU, SE, SK, UK, ZA) US Product Information Centre Toll-free number: 1-800-27 27 537
www.parker.com